Pump and Control Systems

STANCOR Oil-Minder ® Model SE-100 Simplex & Duplex Pump and Control Systems Features             NEMA 4x weathertight corrosion resis...
Author: Curtis Warren
60 downloads 0 Views 2MB Size
STANCOR Oil-Minder

®

Model SE-100 Simplex & Duplex

Pump and Control Systems

Features            

NEMA 4x weathertight corrosion resistant polycarbonate enclosures Stainless steel sensor probe with patented electronic technology that repels contamination Single direct plug-in power source for operation of entire system Solid state components Alarms, lights, silence switch, and remote monitoring circuit for oil, high liquid, and high amperage conditions Solid state “push to test” switch conveniently performs all pump and control diagnostic tests Complete factory assembly and testing insures quality of entire pump and control system Patented - Pat. #4,715,785, #4,752,188, #6,203,281 and others pending Oil-Minder® System can be combined with a variety of different pumps and valves Choice of: 115v, 208 or 220v (1 phase) OR 208v, 230v, 460v (3 phase) LED indicator lights for oil spill, power, high liquid level, overload, and pump run Factory tested as a fully functioning system

“There Is Only One Oil-Minder® System and Stancor Makes It” Quality You Can Believe In

Description of Stancor Duplex Oil-Minder® Systems The Stancor Duplex Oil-Minder® System operates as follows:

The Duplex Oil-Minder® Control alternates each pump upon start-up, assuring equal run time and wear. In the event of heavy inflow, both pumps will operate together until the water level recedes and both pumps are deactivated. The high level/lag pump float will activate an alarm if the water condition continues after a pre-set time point is reached (set for 6 seconds, adjustable between 6 seconds and 10 minutes). An alarm and separate diagnostic LED lights are provided for oil alert, high water, and high amperage (pump overload) conditions. Remote monitoring relays are also provided for alert conditions. A silence and reset switch clears the alarm mode once a fault is addressed. In addition, there are LED lights to “power” the system and to indicate “pump 1” and “pump 2” activation. As with all Stancor OilMinder® Systems, oil is contained in the sump while water is pumped on a fully automatic basis, assuring protection of the environment, personnel, and valuable equipment–even during an alarm condition.

Features included in standard package

Solid state NEMA 4x control panel Separate LED indicator lights on NEMA 4x control for A) oil alert, B) high water, C) high motor amps, D) power to system, and E) pump activation

O/M SMPLX O/M DPLX

x

x

x

x

Self cleaning, hermetically sealed stainless steel oil detection probe (patented technology)

x

x

Float switches for pump activation and high water alert

x

x

Separate oil and water monitoring relays for alert conditions at remote locations

x

x

High decibel, water tight horn and silence switch for alert conditions

x

x

Direct plug-in activation of entire pump and control system from the main control panel (6’ cord and molded plug included, single phase systems)

x

x

Factory hard wiring of pump, oil probe, and floats into NEMA 4x junction box, when spec’d

x

x

Factory hard wiring of pump, oil probe, and floats directly into main NEMA 4x control panel when spec’d

x

Automatic alternator for lead/lag operation “Push to Test” button on panel for all pump and control diagnostic functions

2

x

x x

x

SE-100 HH Pump Data: Discharge Impeller type Strainer openings Pump weight

2” NPT Semi open 1/2” 43 lbs

Motor Data; Motor rating Voltage single phase Amps single phase Voltage three phase Amps three phase Motor RPM Insulation class

1 HP 115/230 15/6 230/460 3/1.5 3450 F

17.3”

Construction Materials: Motor housing Impeller Diffuser Fasteners Strainer Mechanical seals Cable Elastomers

Cast iron Cast iron Cast iron Stainless steel PVC Carbon/ceramic PVC jacket Buna®

7.125” 9.75”

Not recommended for use under 30’ TDH

H(FT)

Pump EFF.%

100

100

90

90

80

80

H

70

70

60

60

50

50

EFF

40

40

30

30

20

20

BHP

10

10 0

0 (BHP)

0

10

20

30

40

Capacity (GPM) 4

50

60

70

80

Stancor SE-100 STD 50

40

30 Head (ft) 20

10

Amp Draw 120 V

0 0

20

40

60

80

100

120

140

Quantity (GPM)

Additional Pump Selections ASME A 17.1 Section 2.2.2.5 (2007) requires that, for each building elevator, the elevator sump pump shall be capable of pumping at least 3,000 gallons per hour. Therefore, after considering vertical lift and pipe friction losses, a larger pump selection may be necessary for certain projects. No matter what the pump capacity requirement may be, Stancor has an Oil-Minder® System that will do the job. Please refer to the chart below for additional commonly specified pump selections. Stancor manufactures pumps up to 75 HP, details of which can be found at www.stancorpumps.com.

Specifications Pump & System Model SE-40O/M SE-50O/M SE-100O/M SE-200 O/M SV-300 O/M SV-500 O/M SV-750 O/M

HP

4/10 1/2 1 2 3 5 7.5

Output Voltage

115 115/220/460 115/220/460 220/230/460 230/460 230/460 230/460

Discharge Amps In.

5 8/4/2 14/7/3.5 21/10/5.5 9/5.2 15/8.6 22.5/12.8

2” 2” 2” 2” (3”) 3” (4”) 3” (4”) 3” (4”)

Rated Max. Head (ft) 22 37 50 62 70 80 90

Max. Capacity 64GPM 74GPM 100 GPM 172 GPM 210 GPM 280 GPM 330 GPM

Cable Length (ft) 16 16 33 33 33 33 33

1. Guiderail systems are available for all Stancor pumps 2. Elbow with female threaded connection provided, standard 3. 208V available as special order 3

DIMENSION DRAWING Standard Freestanding Type

Optional Guiderail Type CAN LI CONTINUOUSLY RUNNING WATER LEVEL L W.L • LOWEST RUNNING WATER LEVEL

D

A-A VIEW 2-010

70

[ANCHOR BOLT)

H3

AA DIMENSION TABLE G/R PUMP OUTPUT TYPE TYPE HP A N/A Freestanding 0.5 223 N/A Freestanding 1 223 N/A Freestanding 2 390 N/A Freestanding 3 390 N/A Freestanding 5 525 N/A Freestanding 7.5 525 G/R 200 Guiderail 1 475 G/R 200 Guiderail 2 550 G/R 200 Guiderail 3 550 G/R 750 Guiderail 5 690 0/R 750

Guiderail

Tungsten edge Cutter Impeller

STANCOR

7.5

Al 70 70 103 103 125 125 80 103 103 125

A2 115 115 235 235 295 295 300 350 350 460

DIMENSION (mm) 0 D1 D2 H Fll 132 63 69 395 338 132 63 69 425 368 210 105 105 530 400 210 105 105 550 420 250 117 133 635 520 250 117 133 675 560 165 77 78 490 390 210 105 105 600 470 210 105 105 620 490 250 117 133 730 585

W 180 180 180 250

W1 100 100 100 250

690 125 460 250 117 133 770 625 265 360 230 250

250

High Efficiency Effluent Impeller

H2 125 125 150 150 200 200 190 216 216 265

H3 156 156 155 155 275 275 267 360 360 360

L 150 150 150 230

Vortex Non-Clog Impeller

Stancor, Inc. • 515 Fan Hill Road • Monroe, CT 06468 203-268-7513 • Fax 203-268-7958 • stancorpumps.com

Guiderail Installation