CLD-DS61 Rev 1A
Product family data sheet
Cree® XLamp® XM-L2 LEDs
Product Description
FEATURES
Table of Contents
The XLamp XM-L2 LED builds on
• Available in white, 80‑CRI white,
Flux Characteristics..................... 2
the unprecedented performance of the original XM-L, increasing lumen output up to 20% while providing
• ANSI‑compatible chromaticity bins
Characteristics........................... 3 Relative Spectral Power Distribution............................... 3
a single die LED point source for
• Binned at 85 °C
Relative Flux vs. Junction
precise optical control. The XM-L2
• Maximum drive current:
Temperature.............................. 4
LED shares the same mechanical and optical footprint as the original XM-L, providing a seamless upgrade path and shortened design cycle. XLamp XM-L2 LEDs are the ideal choice
for
where
high
lighting light
applications output
and
3000 mA • Low thermal resistance: 2.5 °C/W
Electrical Characteristics.............. 4 Thermal Design.......................... 5 Relative Flux vs. Current ............ 5
• Wide viewing angle: 125°
Relative Chromaticity vs. Current.. 6
• Unlimited floor life at
Relative Chromaticity vs.
≤ 30 ºC/85% RH • Reflow solderable - JEDEC J‑STD‑020C
Temperature.............................. 6 Typical Spatial Distribution........... 7 Reflow Soldering Characteristics... 8
maximum efficacy are required,
• Electrically neutral thermal path
Notes........................................ 9
such as LED light bulbs, outdoor
• UL-recognized component
Mechanical Dimensions..............10
lighting, portable lighting, indoor lighting and solar-powered lighting.
WWW.CREE.COM/XLAMP
85‑CRI white and 90‑CRI white
(E349212)
Tape and Reel...........................11 Packaging.................................12
Copyright © 2012-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.
Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp
xlamp xm-l2 leds
Flux Characteristics (TJ = 85 °C) The following table provides several base order codes for XLamp XM-L2 LEDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order-code nomenclature, please consult the XLamp XM-L Family Binning and Labeling document.
CCT Range Color Min.
Cool White
5000 K
Max.
8300 K
Neutral White
3700 K
5000 K
Warm White
2600 K
3700 K
80-CRI White
2600 K
4300 K
85-CRI White
90-CRI White
2600 K
2600 K
3200 K
3200 K
Base Order Codes Min. Luminous Flux (lm) @ 700 mA
Calculated Minimum Luminous Flux (lm) @ 85 °C**
Order Code
Group
Flux (lm) @ 85 °C
Flux (lm) @ 25 °C*
1000 mA
1500 mA
2000 mA
T5
260
296
357
502
631
XMLBWT-00-0000-0000T5051
T6
280
318
385
541
679
XMLBWT-00-0000-0000T6051
U2
300
341
412
580
728
XMLBWT-00-0000-0000U2051
T4
240
273
330
464
582
XMLBWT-00-0000-000LT40E4
T5
260
296
357
502
631
XMLBWT-00-0000-000LT50E4
T2
200
227
275
386
485
XMLBWT-00-0000-000LT20E7
T3
220
250
302
425
534
XMLBWT-00-0000-000LT30E7
T2
200
227
275
386
485
XMLBWT-00-0000-000HT20E7
T3
220
250
302
425
534
XMLBWT-00-0000-000HT30E7
S4
164
186
225
317
398
XMLBWT-00-0000-000PS40E7
S5
172
196
236
332
417
XMLBWT-00-0000-000PS50E7
S6
182
207
250
352
442
XMLBWT-00-0000-000PS60E7
S4
164
186
225
317
398
XMLBWT-00-0000-000US40E7
S5
172
196
236
332
417
XMLBWT-00-0000-000US50E7
S6
182
207
250
352
442
XMLBWT-00-0000-000US60E7
Notes: •
Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
•
Typical CRI for Cool White (5000 K – 8300 K CCT) is 65.
•
Typical CRI for Neutral White (3700 K – 5000 K CCT) is 75.
•
Typical CRI for Warm White (2600 K – 3700 K CCT) is 80.
•
Minimum CRI for 80-CRI White is 80.
•
Minimum CRI for 85-CRI White is 85.
•
Minimum CRI for 90-CRI White is 90.
*
Flux values @ 25 °C are calculated and are for reference only.
** Calculated flux values at 1000 mA, 1500 mA and 2000 mA are for reference only.
® ® Copyright © 2010 2012-2013 Cree, All reserved. rights reserved. The information in this document is to subject to without change notice. withoutCree, notice. , logo the Cree logo and aretrademarks registered Cree, Inc. AllInc. rights The information in this document is subject change theCree Cree and XLamp areXLamp registered trademarks of Cree, Inc.of Cree, Inc.
2
xlamp xm-l2 leds
Characteristics Characteristics
Unit
Thermal resistance, junction to solder point
°C/W
Viewing angle (FWHM) Temperature coefficient of voltage
Minimum
Typical
Maximum
2.5
degrees
125
mV/°C
-1.6
ESD classification (HBM per Mil-Std-883D)
Class 2
DC forward current
mA
3000
Reverse voltage
V
-5
Forward voltage (@ 700 mA, 85 °C)
V
2.85
Forward voltage (@ 1500 mA, 85 °C)
V
3.05
Forward voltage (@ 3000 mA, 85 °C)
V
3.3
LED junction temperature
°C
3.5
150
Relative Spectral Power Relative Spectral Power Distribution
Relative Radiant Power (%)
100
80
60
5000K - 8300K CCT 3700K - 5000K CCT 2600K - 3700K CCT
40
20
0 380
430
480
530
580
630
680
730
780
Wavelength (nm)
® ® Copyright © 2010 2012-2013 Cree, All reserved. rights reserved. The information in this document is to subject to without change notice. withoutCree, notice. , logo the Cree logo and aretrademarks registered Cree, Inc. AllInc. rights The information in this document is subject change theCree Cree and XLamp areXLamp registered trademarks of Cree, Inc.of Cree, Inc.
3
xlamp xm-l2 leds
Relative Flux Output vs. Junction Temperature Relative Flux vs. Junction Temperature (IF = 700 mA)
Relative Luminous Flux (%)
120
100
80
60
40
20
0 25
50
75
100
125
150
Junction Temperature (ºC)
Electrical Characteristics (Tj = 85°C)
Electrical Characteristics (TJ = 85 °C) 3000 2800 2600
Forward Current (mA)
2400 2200 2000 1800 1600 1400 1200 1000 800
600 400 200 0 2.60
2.80
3.00
3.20
3.40
Forward Voltage (V)
® ® Copyright © 2010 2012-2013 Cree, All reserved. rights reserved. The information in this document is to subject to without change notice. withoutCree, notice. , logo the Cree logo and aretrademarks registered Cree, Inc. AllInc. rights The information in this document is subject change theCree Cree and XLamp areXLamp registered trademarks of Cree, Inc.of Cree, Inc.
4
xlamp xm-l2 leds
Thermal Design The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is
Thermal Design crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to
Cool White
ambient in order to optimize lamp life and optical characteristics. 3500
Maximum Current (mA)
3000 2500 2000 1500
Rj-a = 4°C/W
1000
Rj-a = 7°C/W Rj-a = 10°C/W
500
Rj-a = 15°C/W
0 0
25
50
75
100
125
150
Ambient Temperature (ºC)
Relative Intensity vs. Current (Tj = 85°C)
Relative Flux vs. Current (TJ = 85 °C)
Relative Luminous Flux (%)
350 300
250 200 150 100 50 0 0
200
400
600
800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000
Forward Current (mA)
® ® Copyright © 2010 2012-2013 Cree, All reserved. rights reserved. The information in this document is to subject to without change notice. withoutCree, notice. , logo the Cree logo and aretrademarks registered Cree, Inc. AllInc. rights The information in this document is subject change theCree Cree and XLamp areXLamp registered trademarks of Cree, Inc.of Cree, Inc.
5
xlamp xm-l2 leds
Relative Chromaticity Vs. Current, WW
Relative Chromaticity vs. Current (Warm White) 0.012
0.008
0.004
ΔCCx
0.000
ΔCCy
-0.004
-0.008
-0.012 0
500
1000
1500
2000
2500
3000
Current (mA) Relative Chromaticity Vs. Temperature WW
Relative Chromaticity vs. Temperature (Warm White) 0.012
0.008
0.004
ΔCCx 0.000
ΔCCy
-0.004
-0.008
-0.012 25
50
75
100
125
150
Tsp (°C)
® ® Copyright © 2010 2012-2013 Cree, All reserved. rights reserved. The information in this document is to subject to without change notice. withoutCree, notice. , logo the Cree logo and aretrademarks registered Cree, Inc. AllInc. rights The information in this document is subject change theCree Cree and XLamp areXLamp registered trademarks of Cree, Inc.of Cree, Inc.
6
xlamp xm-l2 leds
Typical Spatial Radiation Pattern Typical Spatial Distribution
Relative Luminous Intensity (%)
100
80
60
40
20
0 -90
-70
-50
-30
-10
10
30
50
70
90
Angle (º)
® ® Copyright © 2010 2012-2013 Cree, All reserved. rights reserved. The information in this document is to subject to without change notice. withoutCree, notice. , logo the Cree logo and aretrademarks registered Cree, Inc. AllInc. rights The information in this document is subject change theCree Cree and XLamp areXLamp registered trademarks of Cree, Inc.of Cree, Inc.
7
xlamp xm-l2 leds
Reflow Soldering Characteristics In testing, Cree has found XLamp XM-L2 LEDs to be compatible with JEDEC J‑STD‑020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment.
Profile Feature
Lead-Based Solder
Lead-Free Solder
3 °C/second max.
3 °C/second max.
Preheat: Temperature Min (Tsmin)
100 °C
150 °C
Preheat: Temperature Max (Tsmax)
150 °C
200 °C
60-120 seconds
60-180 seconds
183 °C
217 °C
60-150 seconds
60-150 seconds
215 °C
260 °C
10-30 seconds
20-40 seconds
6 °C/second max.
6 °C/second max.
6 minutes max.
8 minutes max.
Average Ramp-Up Rate (Tsmax to Tp)
Preheat: Time (tsmin to tsmax) Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) Peak/Classification Temperature (Tp) Time Within 5 °C of Actual Peak Temperature (tp) Ramp-Down Rate Time 25 °C to Peak Temperature
Note: All temperatures refer to the topside of the package, measured on the package body surface.
® ® Copyright © 2010 2012-2013 Cree, All reserved. rights reserved. The information in this document is to subject to without change notice. withoutCree, notice. , logo the Cree logo and aretrademarks registered Cree, Inc. AllInc. rights The information in this document is subject change theCree Cree and XLamp areXLamp registered trademarks of Cree, Inc.of Cree, Inc.
8
xlamp xm-l2 leds
Notes Lumen Maintenance Projections Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED lumen maintenance. For information on the specific LM‑80 data sets available for this LED, refer to the public LM-80 results document at www.cree.com/xlamp_app_notes/LM80_results. Please read the XLamp Long-Term Lumen Maintenance application note at www.cree.com/xlamp_app_notes/lumen_ maintenance for more details on Cree’s lumen maintenance testing and forecasting. Please read the XLamp Thermal Management application note at www.cree.com/xlamp_app_notes/thermal_management for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature.
Moisture Sensitivity In testing, Cree has found XLamp XM-L2 LEDs to have unlimited floor life in conditions ≤30 ºC/85% relative humidity (RH). Moisture testing included a 168‑hour soak at 85 ºC/85% RH followed by 3 reflow cycles, with visual and electrical inspections at each stage. Cree recommends keeping XLamp LEDs in their sealed moisture-barrier packaging until immediately prior to use. Cree also recommends returning any unused LEDs to the resealable moisture‑barrier bag and closing the bag immediately after use.
UL Recognized Component Level 4 enclosure consideration. The LED package or a portion thereof has been investigated as a fire and electrical enclosure per ANSI/UL 8750.
Vision Advisory Claim WARNING: Do not look at exposed lamp in operation. Eye injury can result. See the LED Eye Safety application note at www.cree.com/xlamp_app_notes/led_eye_safety.
® ® Copyright © 2010 2012-2013 Cree, All reserved. rights reserved. The information in this document is to subject to without change notice. withoutCree, notice. , logo the Cree logo and aretrademarks registered Cree, Inc. AllInc. rights The information in this document is subject change theCree Cree and XLamp areXLamp registered trademarks of Cree, Inc.of Cree, Inc.
9
4.78
xlamp xm-l2 leds C
R2.26
Mechanical Dimensions All measurements are ±.13 mm unless otherwise indicated. 4.7 3.9 .600
6
5
NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND 6 5 OF CREE, INC. THIS PLOT CONFIDENTIAL INFORMATION MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY NOTICE UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT 4.7 .400 CREE CONFIDENTIAL. THIS PLOT AND THE OF INFORMATION CREE INC. CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT OF CREE INC.
4
4
2 REV
3
2
DESCRIPTION
1
B
ADDED DOME RA
REVISONS
D
REV
DESCRIPTION
BY
DATE
A
INITIAL RELEASE
DC
11/14/12
3.78
3.78
3.02
3.02
5.000 5.00
.400
3
B
Anode
.50
.73 .50
0.73
APP'D
2.78
2.78
.400 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .25 .XXX ± .125 X° ± .5 °
RECOMMENDED STENCIL PATTERN SHADED AREA IS OPEN 5.000 THIRD ANGLE PROJECTION
5.00
FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 °
Anode
D. CRONIN CHECK
4600 Silicon Drive Durham, N.C 27703
11/14/12 DATE
--
Phone (919) 313-5300
--
Fax (919) 313-5558
--
--
MATERIAL
--
TITLE
OUTLINE DRAWING, 5050 XMLB SIZE
--
SCALE
2610-00032 SHEET
16.000
2
4.78
4.78
REV.
DRAWING NO.
C
FINAL PROTECTIVE FINISH
3
A
DATE
APPROVED
SURFACE FINISH: 1.6
4
DATE
DRAWN BY
A OF
1 /1
1
C
R2.190 R2.26
Top View
Bottom View
Side View 4.7 3.9
4.8 3.8 4.8
4.7 3.9
.500
3.8 .500
.600
.600
B
4.8
.500 .500
4.7
.500
.400
2.782 2.782 A .400
.400
4.7
.400
4.8
.500
.400
.400 .400
.400 Recommended PCB Solder RECOMMENDED PCB SOLDER PAD
RECOMMENDED STENCIL PATTERN SHADED AREA IS OPEN
Pad
Recommended Stencil Pattern UNLESS OTHERWISE SPECIFIED RECOMMENDED STENCIL PATTERN D. CRONIN (Shaded Area Is Open) DIMENSIONS ARE IN DRAWN BY
SHADED AREA IS OPEN
RECOMMENDED PCB SOLDER PAD
THIRD ANGLE PROJECTION
6
5
4
MILLIMETERS AND AFTER FINISH. THIRD ANGLECHECK PROJECTION -TOLERANCE UNLESS SPECIFIED: .XX ± .25 APPROVED .XXX ± .125 -X° ± .5 ° FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 ° SURFACE FINISH: 1.6
6
5
4
3
MATERIAL
3
--
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: DATE .XX ± .25 .XXX ± .125 11/14/12 X° ± .5 ° DATE FOR SHEET METAL PARTS ONLY -.X ± 1.5 .XX ± .75 TITLE -.XXX ± .25 X° ± .5 °
D. CRONIN
08/1/11 DATE
-APPROVED
-MATERIAL
-DATE
4600 Silicon Drive -- 27703 Durham, N.C
O
Phone (919) 313-530 Fax (919) 313-5558
--
DATE
OUTLINE DRAWING, 5050 XM FINAL PROTECTIVE FINISH
--
SURFACE FINISH: 1.6 SIZE
FINAL PROTECTIVE FINISH
--
DATE
DRAWN BY
CHECK
SCALE
C
DRAWING NO.
2 2610-00032 SHEET
16.000
2
1
® ® Copyright © 2010 2012-2013 Cree, All reserved. rights reserved. The information in this document is to subject to without change notice. withoutCree, notice. , logo the Cree logo and aretrademarks registered Cree, Inc. AllInc. rights The information in this document is subject change theCree Cree and XLamp areXLamp registered trademarks of Cree, Inc.of Cree, Inc.
10
OF
6
5
4
3
2.00[.079]
4.00[.157]
1
2 REVISIONS
NOTICE EE CONFIDENTIAL. THIS PLOT AND THE INFORMATION NTAINED WITHIN ARE THE PROPRIETARY AND NFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT Y NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY AUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT CREE INC.
DESCRIPTION
REV
BY
DATE
APP'D
POCKET SIZE +.10 +.0039 .0591 -.00 -.0000 [ ]
Do1.50
P2
1.75[.069] E1
Po
Ao -
5.40mm [.213"]
Bo -
5.40mm [.213"]
Ko -
3.35mm [.132"]
xlamp xm-l2 leds D
Tape and Reel 3.0°
5.40[.213] Bo
3 12.00[.472] All Cree carrier tapes conform to EIA-481D, Automated Component Handling Systems Standard. 6 5 4 3
5.50[.217]F
6
5
4
NOMINAL
OF CREE INC.
D
D
2.00[.079] 2.00[.079] P2 1.50[.059] 4.00[.157] D1 4.00[.157] Po
8.00[.315] P
REV
12.30 [.484] MAX W
10.25 [.404] E2
REV
+.10 +.0039 Do1.50 .0591 +.0039 -.00 +.10 .0591 -.0000 [] Do1.50 -.00 -.0000 [ ]
P2
6
5
C
NOTICE NTIAL. THIS PLOT AND THE INFORMATION THIN ARE THE PROPRIETARY AND INFORMATION OF CREE, INC. THIS PLOT OPIED, REPRODUCED OR DISCLOSED TO ANY D PERSON WITHOUTTHE WRITTEN CONSENT
5.40[.213]
4
3.0°
A B
BY
1 DATE
APP'D DATE APP'D
D
Ao
B
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .01 .XXX ± .005 X° ± .5 ° FOR SHEET METAL PARTS ONLY .X ± .06 .XX ± .03 .XXX ± .010 X° ± .5 °
1
C
BY
DATE
DDS
11/8/10
DC
2/26/12
5
4
8 6
BS
A
Loaded Pockets (1000 Lamps)
1.50[.059] Phone (919) 313-5300 Fax (919) 313-5558 D1 1.50[.059] D1
8.00[.315] DATE 8.00[.315] P TITLE P
APPROVED
SIZE
A
FINAL PROTECTIVE FINISH
User Feed Direction
REV.
DRAWING NO.
2402-00011 7.0°
SCALE
DRAWING SCALE 2
SHEET
7.0°
1
A OF
4 1.75 3.35[.132] 3.35[.132] 3 Ko Ko
START
12
.36[.014] D T .36[.014] T
A
XM 5050 CARRIER TAPE
MATERIAL
5.40[.213] 5.40[.213] Ao
ANODE SIDE
4600 Silicon Drive Durham, N.C 27703
4/23/10 DATE
CATHODE SIDE 4
5
Trailer 160mm (min) of empty pockets sealed with tape (15 pockets min.)
D. CRONIN CHECK
3
A
B
3.35 2
1
2400-00009
CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275 CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275 INDEX
QTY
ITEM
1
1
2400-00009-CORE
DRAWN BY
COMMENTS
DATE
UNLESS OTHERWISE SPECIFIED DATE 4/23/10 2 D. CRONIN 2DRAWN BY2400-00009-REEL UNLESS ARE OTHERWISE SPECIFIED DIMENSIONS IN INCHES D. CRONIN 4/23/10 DATE DIMENSIONS ARE IN INCHESCHECK AND AFTER FINISH. CHECK DATE AND AFTERSPECIFIED: FINISH. TOLERANCE UNLESS TOLERANCE .XX ± UNLESS .01 SPECIFIED: APPROVED DATE TITLE .XX ± .01 .XXX ± .005 APPROVED DATE TITLE X° ±.XXX .5± ° .005 THIRD ANGLE PROJECTION MATERIAL X° PARTS ± .5 ° FOR SHEET METAL ONLY Leader THIRD ANGLE PROJECTION MATERIAL FOR.XSHEET ± METAL .06 PARTS ONLY DRAWING NO. 400mm (min.) of SIZE .XX .X ± ±.03 .06 DRAWING NO. SIZE FINAL PROTECTIVE FINISH ± .03 empty pockets with .XXX .XX ± .010 FINAL PROTECTIVE FINISH X° ±.XXX .5± ° .010 at least 100mm SCALE X° ± .5 ° SURFACE FINISH: 63 SCALE sealed by tape DRAWING SCALE SURFACE FINISH: 63 DRAWING SCALE
Ao
C 4600 Silicon Drive Durham, N.C 27703 4600 Silicon Drive Durham, N.C 27703 Phone (919) 313-5300 Phone (919) 313-5300 Fax (919) 313-5558 Fax (919) 313-5558
XMXM 5050 CARRIER TAPE 5050 CARRIER TAPE 2402-00011 A 2402-00011 A
6
(405 empty pockets min.)
4
5
3
4
2
3
A
REV.
A
6
SHEET
OF
SHEET
1
2
1OF / 1
1
D
REV.
A
1 /1
12.4 +.2 .0 MEASURED AT HUB
C
C
330 +.25 -.75
16.4 +0.2 .0 MEASURED AT HUB
THIRD ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .25 .XXX ± .125 X° ± .5 ° FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 ° SURFACE FINISH:
5
4
1.6
3
1.9±.4
DATE
DRAWN BY
D. CRONIN CHECK
21 ±.4
4600 Silicon Drive Durham, N.C 27703
06/08/10 DATE
--
Phone (919) 313-5300
--
Fax (919) 313-5558
A
DATE
APPROVED
--
--
MATERIAL
TITLE
13.1 ±.2
--
SIZE
FINAL PROTECTIVE FINISH
--
SCALE
XM LOADING SPEC REV.
DRAWING NO.
C
2402-00012 SHEET
3.000
2
B OF
B
1 /1
1
12.4 +1.0 -.5 MEASURED AT EDGE 60°
60°
REVISONS REV
DESCRIPTION
BY
DATE
APP'D
® ® Copyright © 2010 2012-2013 Cree, All reserved. rights reserved. The information in this document is to subject to without change notice. withoutCree, notice. , logo the Cree logo and aretrademarks registered Cree, Inc. AllInc. rights The information in this document is subject change theCree Cree and XLamp areXLamp registered trademarks of Cree, Inc.of Cree, Inc. UNLESS OTHERWISE SPECIFIED DRAWN BY
A
THIRD ANGLE PROJECTION
B
1 /1
B
B
C
APP'D
DATE
DRAWN BY
63
NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTANED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC.
6
D
CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275
SURFACE FINISH:
D
2
BY
5.40[.213] 5.40[.213] Bo Bo
3.0°
12.00[.472] 12.00[.472] NOMINAL NOMINAL REVISONS
[.484] 10.25 12.30DESCRIPTION 12.30 [.484] MAX Loaded pocket count was 750 [.404]10.25 MAX [.404] WANODE E2 MADE CATHODE AND W NOTE LARGER E2
REV
3.35[.132] Ko
B
END
5.50[.217]F 5.50[.217]F
3
C
THIRD ANGLE PROJECTION
6
REVISIONS REVISIONS DESCRIPTION DESCRIPTION
BoBo - - 5.40mm [.213"] 5.40mm [.213"] KoKo - - 3.35mm [.132"] 3.35mm [.132"]
1.75[.069] E1 1.75[.069] E1
.36[.014] T
Po
1
2
POCKET SIZE POCKET SIZE in mm. All dimensions AoAo - - 5.40mm [.213"] 5.40mm [.213"]
B
7.0°
2
C
NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION NOTICE CONTAINED WITHIN ARE THETHIS PROPRIETARY ANDINFORMATION CREE CONFIDENTIAL. PLOT AND THE CONFIDENTIAL INFORMATION CREE, INC. THIS PLOT CONTAINED WITHIN AREOF THE PROPRIETARY AND MAY NOT BE COPIED, INFORMATION REPRODUCEDOF ORCREE, DISCLOSED TO PLOT ANY CONFIDENTIAL INC. THIS UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY OF CREE INC. UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
DIMENSIONS ARE IN INCHES AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .01 .XXX ± .005 X° ± .5 °
FOR SHEET METAL PARTS ONLY
D. CRONIN
CHECK
DATE
4600 Silicon Drive Durham, N.C 27703
09/29/09
DATE
-APPROVED
-MATERIAL
11
Phone (919) 313-5300
--
Fax (919) 313-5558
DATE
--
TITLE
REEL, 13" X 12MM, 3 PIECE SNAP
A
A
xlamp xm-l2 leds
Humidity Indicator Card (inside bag)
Packaging
Dessicant (inside bag)
Unpackaged Reel
Label with Cree Bin Code, Qty, Reel ID Packaged Reel
Label with Cree Bin Code, Qty, Lot #
Vacuum-Sealed Moisture Barrier Bag Label with Cree Order Code, Qty, Reel ID, PO #
Label with Cree Bin Code, Qty, Reel ID
Label with Custo Code, Qty, Reel I
Boxed Reel
Label with Cree Order Code, Qty, Reel ID, PO #
Patent Label
Label with Cree Bin Code, Qty, Reel ID
Patent Label
® ® Copyright © 2010 2012-2013 Cree, All reserved. rights reserved. The information in this document is to subject to without change notice. withoutCree, notice. , logo the Cree logo and aretrademarks registered Cree, Inc. AllInc. rights The information in this document is subject change theCree Cree and XLamp areXLamp registered trademarks of Cree, Inc.of Cree, Inc.
12
