Windows POS Terminal

ST-M30

Windows XP / Windows 7 / WEPOS 1.1 / POSReady 2009 / POS Ready 7 Operating System Setup Guide

Second Edition :

15 Jun 2012

Revision Record No. JEA-02533

Windows XP / Windows 7 / WEPOS 1.1 / POSReady 2009 / POS Ready 7 Operating System Setup Guide Rev. No.

Date

Sections

1

16 Dec, 2011

---

2

15 Jun, 2012

2.1.2

Description First Release Add a installation print screen for WEPOS 1.1 Add notification to support for SP3 update

2.1.3

Add a installation print screen for POSReady 2009

Table of Contents 1. Overview .................................................................................................................. 2 2. Set up for Windows XP (or WEPOS 1.1, POSReady 2009) ................................... 3 2.1.

Operating System Installation ....................................................................................... 3 2.1.1. Windows XP installation ............................................................................................................................................... 3 2.1.2. WEPOS 1.1 installation ................................................................................................................................................. 6 2.1.3. POSReady 2009 Installation ..................................................................................................................................... 13 2.2. Intel Chipset Driver Installation .................................................................................... 20 2.3. Intel Graphic Accelerator Driver Installation................................................................. 25 2.4. Network Driver Installation .......................................................................................... 29 2.4.1. Intel Network Driver installation ............................................................................................................................. 29 2.4.2. Realtek Network Driver installation ....................................................................................................................... 31 2.5. Realtek Audio Driver Installation ................................................................................. 33 2.6. Setup for Display panel ............................................................................................... 36

3. Setup for Windows 7 Professional (or POS Ready 7) ........................................ 37 3.1. 3.2. 3.3. 3.4.

Operating System Installation ..................................................................................... 37 Intel Chipset Software Installation ............................................................................... 39 Intel Graphic Accelerator Driver Installation................................................................. 42 Network Driver Installation .......................................................................................... 46 3.4.1. Intel Network Driver installation ............................................................................................................................. 46 3.4.2. Realtek Network Driver installation ....................................................................................................................... 49 3.5. Realtek Audio Driver Installation (Windows 7 only) ..................................................... 51 3.6. Setup for Display ........................................................................................................ 53

4. Setup for RAID ....................................................................................................... 54 4.1.

Setup for RAID HDD ................................................................................................... 54

5. Optional Settings and Restriction........................................................................ 57 5.1.

Optional settings procedure ........................................................................................ 57 5.1.1. USB-HUB Power Management ............................................................................................................................... 57 5.1.2. Wake On LAN Settings ............................................................................................................................................... 59 5.1.3. Dual Display connection combinations list ......................................................................................................... 62 5.2. Limitation .................................................................................................................... 63 5.2.1. Limitation for Wake up by USB keyboard / mouse from S3 ....................................................................... 63 5.2.2. Extended display mode in POSReady 2009 ....................................................................................................... 64 5.2.3. Limitation of Windows Time Service ..................................................................................................................... 65

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

© Copyright Toshiba TEC Corporation All rights reserved. It is prohibited to use or duplicate a part or whole of this document without the permission of Toshiba TEC Corporation. This document is subject to change without prior notice. Trademark Notification *

Microsoft, Windows, Windows XP, WEPOS 1.1, POSReady 2009, Windows 7 and POS Ready 7 are registered trademarks of Microsoft Corporation in the United States and/or other countries. The official name of Windows is the “Microsoft Windows Operating System”.

*

All other product names mentioned in this document are trademarks or registered trademarks of their respective owners.

1

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

1.

JEA-02533

Overview This document describes the procedures and precautions for Windows operating system and the drivers installation on the ST-M30. The outline of procedures to install Windows operating system and the drivers on the ST-M30 are as follows: 1. Operating System Installation 2. Intel Chipset Software Installation 3. Intel Graphic Accelerator Driver Installation 4. Intel Network Driver Installation 5. Realtek Network Driver Installation 6. Realtek Audio Driver Installation 7. Setup for Display There is supplementary setup document for each display type.. ·

TFTST-B20: TFTST-B20 Setup Guide

2

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

2.

JEA-02533

Set up for Windows XP (or WEPOS 1.1, POSReady 2009)

2.1. Operating System Installation 2.1.1. Windows XP installation To Install Windows XP operating system into ST-M30, AHCI driver is required to support AHCI and RAID functionality. Without this driver, it might cause blue screen (BSOD) during operating system installation. The following are the steps to install AHCI driver: 1. Create a floppy disk contains the following files in the root directory: iaAhci.inf, iaAhci.cat, iaStor.inf, iaStor.cat, iaStor.sys, and TxtSetup.oem. User can find the above files in the “ST-M30WinVxxx\32bit\5_RAID\1_DOSFloppy” folder in the Driver kit. *xxx means version number of driver kit. 2. If IDE or RAID functionality is required by POS Terminal, user needs to configure BIOS menu item as below: Path: [Advanced] –> [SATA Configuration] Setting: SATA Mode IDE Mode or RAID Mode Aptio Setup Utility - Copyright (C) 2011 Am erican Megatrends, Inc. M ain Advanced Chipset Boot Security Save & Exit

SATA Configuration SATA M ode

[AHCI Mode]

SATA 0

Not Present

SATA 1

Not Present

SATA 2

Not Present

SATA 3

Not Present → ←: Select Scr een ↑ ↓: Select It em Enter: Select +/- : Change Opt. F 1 : General Help F 5: Previous Values F 10 : Save ESC: Exit

V ersion 2.11.1210. Copyright (C) 2011 American M egatrends , Inc.

For the produces to setup the RAID function, please refer to “4.2 Setup for RAID HDD” section. However, BIOS does not have to be set any option if the POS Terminal uses AHCI mode.

3

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3. Once the operating system installation start, press F6 to install a third party SCSI or RAID driver. If the terminal uses IDE mode, follow the instructions of the Windows installer to complete the installation.

4. Wait until the following dialog prompt, select 'S' to specify Additional Device.

4

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

5. Next is to configure which driver option to be installed. AHCI : “Intel(R) Desktop/Workstation/Server Express Chipset SATA AHCI Controller” RAID : “Intel(R) Desktop/Workstation/Server Express Chipset SATA RAID Controller” Subsequently, follow the instructions of the Windows installer to complete the installation. AHCI mode

RAID mode

5

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

2.1.2. WEPOS 1.1 installation To Install Windows XP operating system into ST-M30, AHCI driver is required to support AHCI and RAID functionality. Without this driver, it might cause blue screen (BSOD) during operating system installation. The following are the steps to install AHCI driver: 1. Create a floppy disk contains the following files in the root directory: iaAhci.inf, iaAhci.cat, iaStor.inf, iaStor.cat, iaStor.sys, and TxtSetup.oem. User can find the above files in the “ST-M30WinVxxx\32bit\5_RAID\1_DOSFloppy” folder in the Driver kit. *xxx means version number of driver kit. 2. If IDE or RAID functionality is required by POS Terminal, user needs to configure BIOS menu item as below: Path: [Advanced] –> [SATA Configuration] Setting: SATA Mode IDE Mode or RAID Mode Aptio Setup Utility - Copyright (C) 2011 Am erican Megatrends, Inc. M ain Advanced Chipset Boot Security Save & Exit

SATA Configuration SATA M ode

[AHCI Mode]

SATA 0

Not Present

SATA 1

Not Present

SATA 2

Not Present

SATA 3

Not Present → ←: Select Scr een ↑ ↓: Select It em Enter: Select +/- : Change Opt. F 1 : General Help F 5: Previous Values F 10 : Save ESC: Exit

V ersion 2.11.1210. Copyright (C) 2011 American M egatrends , Inc.

For the produces to setup the RAID function, please refer to “4.2 Setup for RAID HDD” section. However, BIOS does not have to be set any option if the POS Terminal uses AHCI mode.

6

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3. Once the operating system installation start, press F6 to install a third party SCSI or RAID driver. If the terminal uses IDE mode, follow the instructions of the Windows installer.

4. Wait until the following dialog prompt, select 'S' to specify Additional Device.

7

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

5. Next is to configure which driver option to be installed. AHCI : “Intel(R) Desktop/Workstation/Server Express Chipset SATA AHCI Controller” RAID : “Intel(R) Desktop/Workstation/Server Express Chipset SATA RAID Controller” Subsequently, follow the instructions of the Windows installer. AHCI mode

RAID mode

8

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

6. If AHCI or RAID functionality is required by POS Terminal, please select the “Install Mass Storage Device Drivers from Floppy Disk.” check box when the “Install Mass Storage Device Drivers” window appears.

9

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

7. Then, it is required to select “Additional Driver Support” check box under “Optional Software Component Setting” wizard. If “Additional Driver Support” component is not selected on “Optional Software Component Setting” wizard, the “Unknown device” will be shown under processor in device manager after installation. Please refer to below instruction to install “Additional Driver Support” component in ” Optional Software Component Setting” wizard. Please select “Additional Driver Support” check box under “Optional Software Component Setting” wizard.

Please select other options if necessary, and click on the “Next” button. (It is recommended to select all components for more OS functionalities.) Subsequently, follow the instructions of the Windows installer to complete the installation. Note: Unselected components can no longer be added after the WEPOS installation is complete.

10

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

Steps for Update Service Pack after OS installation: It has to update service pack 3 for WEPOS. It might be occurred unexpected error if the service pack was not installed before any driver installation. Note: Please install .NET Framework 3.0 before update the Service Pack 3. 1. First, please download the service pack 3 using following URL: http://www.microsoft.com/download/en/details.aspx?id=3740 2. Next, run the installer, and following window appears. Please click on the “Next” button to start installation.

3. Next, the License Agreement window appears. Select the “I Agree” radio button and click on the “Next” button to continue installation.

11

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

4. The “Select Options” window appears. Please click on the “Next” button to start installation.

5. The installer will prompt for system reboot when the installation is complete. Please click on the “Finish” button to reboot POS Terminal.

12

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

2.1.3. POSReady 2009 Installation To Install Windows XP operating system into ST-M30, AHCI driver is required to support AHCI and RAID functionality. Without this driver, it might cause blue screen (BSOD) during operating system installation. The following are the steps to install AHCI driver: 1. Create a floppy disk contains the following files in the root directory: iaAhci.inf, iaAhci.cat, iaStor.inf, iaStor.cat, iaStor.sys, and TxtSetup.oem. User can find the above files in the “ST-M30WinVxxx\32bit\5_RAID\1_DOSFloppy” folder in the Driver kit. *xxx means version number of driver kit. 2. If IDE or RAID functionality is required by POS Terminal, user needs to configure BIOS menu item as below: Path: [Advanced] –> [SATA Configuration] Setting: SATA Mode IDE Mode or RAID Mode Aptio Setup Utility - Copyright (C) 2011 Am erican Megatrends, Inc. M ain Advanced Chipset Boot Security Save & Exit

SATA Configuration SATA M ode

[AHCI Mode]

SATA 0

Not Present

SATA 1

Not Present

SATA 2

Not Present

SATA 3

Not Present → ←: Select Scr een ↑ ↓: Select It em Enter: Select +/- : Change Opt. F 1 : General Help F 5: Previous Values F 10 : Save ESC: Exit

V ersion 2.11.1210. Copyright (C) 2011 American M egatrends , Inc.

For the produces to setup the RAID function, please refer to “4.2 Setup for RAID HDD” section. However, BIOS does not have to be set any option if the POS Terminal uses AHCI mode.

13

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3. Once the operating system installation start, press F6 to install a third party SCSI or RAID driver. If the terminal uses IDE mode, follow the instructions of the Windows installer.

4. Wait until the following dialog prompt, select 'S' to specify Additional Device.

14

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

5. Next is to configure which driver option to be installed. AHCI : “Intel(R) Desktop/Workstation/Server Express Chipset SATA AHCI Controller” RAID : “Intel(R) Desktop/Workstation/Server Express Chipset SATA RAID Controller” Subsequently, follow the instructions of the Windows installer. AHCI mode

RAID mode

15

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

6. If AHCI or RAID functionality is required by POS Terminal, please select the “Install Mass Storage Device Drivers from Floppy Disk.” check box when the “Install Mass Storage Device Drivers” window appears.

16

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

7. Next, it is necessary to select “Custom” option under “Installation Type” wizard in order to select ”Additional Drivers” check box under “Optional Components” wizard. Please take note that during driver installation (Chipset, Audio, OPOS driver, etc), the screen prompts which requests for ‘*.sys’ file or “*.dll” file will be displayed if: · “Typical” or “Minimum” option is selected under “Installation Type” wizard · “Additional Drivers” component is not select under “Optional Components” wizard. Please refer below for “Additional Drivers” component installation under ”Optional Components” wizard. Select “Custom” in “Installation Type” wizard and click on the “Next” button.

8. Select “Additional Drivers” in “Optional Components” wizard.

Select other options if necessary, and click on the “Next” button. (It is recommended to select all components for more OS functionalities.) Subsequently, follow the instructions of the Windows installer to complete the installation. 17

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

Steps for “Additional Drivers” Component after OS installation: When “Additional Drivers” component is not selected during POSReady2009 installation, user needs to manually install the component as follow. 1. Open “Add or Remove Programs” from “Control Panel”. Then, click on the “Add/Remove Windows Components” button.

2. Select “Additional Drivers” from “Components:” check box. Click on the “Next” button.

18

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3. During installation for the component, you need “Windows Embedded POSReady 2009 Installation CD”. Insert “POSReady installation CD”, and click on the “OK” button.

4. It is recommended to reboot the system after installation.

19

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

2.2. Intel Chipset Driver Installation Run “infinst_autol.exe” in the “ST-M30WinV1xxx\32bit\1_Chipset” folder in the Driver kit. *xxx means version number of driver kit. NOTE) If the terminal is installed with WEPOS 1.1, it has to be updated to service pack 3. Please refer to “Steps for Update Service Pack after OS installation” section. 1. Setup files will be extracted. Then, click on the “Next” button when the following window appears.

2. The “License Agreement” window appears. Confirm the contents. Click on the “Yes” button to agree.

20

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

21

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3. The “Readme File Information” window appears. Click on the “Next” button to start the installation.

4. The “Next” button will be enabled when installation is complete. Please click on the “Next” button to proceed.

22

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

5. Next, the installer will prompt for system reboot. Select “Yes, I want to restart this computer now” option, and then click on the “Finish” button to reboot POS Terminal.

23

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

Note: Chipset driver Installation for POSReady 2009 For POSReady 2009, the installation process will request for several “*.sys” file or “*.dll” file. When the following window appears, please configure the path to the location of “*.sys” file or “*.dll” file respectively. · ·

“*.sys” file is requested -> Set the path to ”c:\windows\system32\drivers” “*.dll” file is requested -> Set the path to ”c:\windows\system32”

A) The following window is to request “*.sys” file.

B) The following window is to request “*.dll” file.

Note: If ”Additional Drivers” of “Optional Components” has been installed during POSReady 2009 OS installation, these screens will not prompt.

24

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

2.3. Intel Graphic Accelerator Driver Installation NOTE: Microsoft .Net 3.0 Framework and above are required for graphic driver installation. Run the “winxp.exe” in the “ST-M30WinV1xxx\32bit\2_Graphic\1_WinXP” folder in the Driver kit. *xxx means version number of driver kit. 1. Please click on the “Next” button to continue.

2. The “Warning” window will appear when the correct .NET Framework has not been installed. Please take note that if user chooses to continue graphic driver installation without .Net 3.0 Framework pre-installed into OS, the application might not work correctly. It is recommended user to confirm .Net 3.0 Framework is installed before proceeding.

25

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3. The following window appears when extraction is complete. Click on the “Next” button.

4. The “License Agreement” window appears. Confirm the contents. Click on the “Yes” button to agree.

26

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

5. The “Readme File Information” window appears. Click on the “Next” button to start the installation.

6. The “Next” button will be enabled when installation is complete. Please click on the “Next” button to proceed.

27

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

7. Next, the installer will prompt for system reboot. Select “Yes, I want to restart this computer now” option, and then click on the “Finish” button to reboot POS Terminal.

8. After rebooting the POS Terminal, user can use Device Manager to confirm the graphic driver has been installed. Make sure that “Intel(R) HD Graphics Family” is registered under the “Display adapters” category.

28

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

2.4. Network Driver Installation 2.4.1. Intel Network Driver installation Unzip the “PROWin32.zip” file in the “ST-M30WinV1xxx\32bit\3_LAN\1_Intel\1_WinXP” folder in the Driver kit. *xxx means version number of driver kit. 1. The confirmation window appears when the “SeupBD.exe” starts running. Click on the “OK” button to start installation. The file is in the “PROCWin32\APPS\SETUP\SETUPBD\Win32” folder.

2. Next, following window will appears when the installation is complete. Click on the “Close” button to close window.

29

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3. User can use Device Manager to confirm the network driver has been installed. Make sure that “Intel(R) 82579LM Gigabit Network Connection” is registered under the “Network adapters” category.

30

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

2.4.2. Realtek Network Driver installation Run the “setup.exe” application located in “ST-M30WinV1xxx\32bit\3_LAN\2_Realtek\1_WinXP” folder of the Driver kit. *xxx means version number of driver kit. 1. The setup window appears when the “setup.exe” starts running. Please click on the “Next” button.

2. Please click on the “Install” button to start the installation.

31

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3. Next, following window will appears when the installation is complete. Click on the “Finish” button to close window.

4. User can use Device Manager to confirm the network driver has been installed. Make sure that “Realtek PCIe GBE Family Controller” is registered under the “Network adapters” category.

32

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

2.5. Realtek Audio Driver Installation Run the “WDM.exe” in the “ST-M30WinV1xxx\32bit\4_Audio\1_WinXP” folder in the Driver kit. *xxx means version number of driver kit. 1. Please click on the “Next” button to start the installation.

2. Next, the installer will prompt for system reboot when the installation is complete. Select “Yes, I want to restart my computer now” option, and then click on the “Finish” button to reboot POS Terminal.

33

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3. User can use Device Manager to confirm the audio driver has been installed. Make sure that “Realtek High Definition Audio” is registered under the “Sound, video and game controllers” category.

34

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

Note: Audio driver Installation for POSReady 2009 For POSReady 2009, the installation process will request for several “*.sys” file or “*.dll” file. When the following window appears, please configure the path to the location of “*.sys” file or “*.dll” file respectively. · ·

“*.sys” file is requested -> Set the path to ”c:\windows\system32\drivers” “*.dll” file is requested -> Set the path to ”c:\windows\system32”

A) The following window is to request “*.sys” file.

B) The following window is to request “*.dll” file.

Note: If ”Additional Drivers” of “Optional Components” has been installed during POSReady 2009 OS installation, these screens will not prompt.

35

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

2.6. Setup for Display panel Each display type has its own supplementary setup document. For TFTST-A20 and TFTST-B20, please refer to “TFTST-A20, TFTST-B20 Setup Guide” which contains: · ·

Installation for ELO (Tyco) Touch panel driver Installation for the driver of other optional equipment

The display setup guide describes the procedures and pre-cautions in setting up each display drivers.

36

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

3.

JEA-02533

Setup for Windows 7 Professional (or POS Ready 7)

3.1. Operating System Installation The following are the steps to install AHCI driver: 1. Save following files to same folder in a storage device (Ex: thumb drive, CD-ROM or Floppy disk etc…). iaAhci.inf, iaAhci.cat, iaStor.inf, iaStor.cat, iaStor.sys, and TxtSetup.oem. User can find the above files in the “ST-M30WinVxxx\32bit\5_RAID\1_DOSFloppy” folder in the Driver kit for 32bit OS. User can find the files in the “ST-M30WinV1xxx\64bit\5_RAID\1_DOSFloppy” folder in the Driver kit for 64bit OS. *xxx means version number of driver kit. 2. If IDE or RAID functionality is required by POS Terminal, user needs to configure BIOS menu item as below: Path: [Advanced] –> [SATA Configuration] Setting: SATA Mode IDE Mode or RAID Mode Aptio Setup Utility - Copyright (C) 2011 Am erican Megatrends, Inc. M ain Advanced Chipset Boot Security Save & Exit

SATA Configuration SATA M ode

[AHCI Mode]

SATA 0

Not Present

SATA 1

Not Present

SATA 2

Not Present

SATA 3

Not Present → ←: Select Scr een ↑ ↓: Select It em Enter: Select +/- : Change Opt. F 1 : General Help F 5: Previous Values F 10 : Save ESC: Exit

V ersion 2.11.1210. Copyright (C) 2011 American M egatrends , Inc.

For the produces to setup the RAID function, please refer to “4.2 Setup for RAID HDD” section. However, BIOS does not have to be set any option if the POS Terminal uses AHCI mode.

37

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3. Next, please select “Load Driver” option under “HDD Selection” wizard in order to install the AHCI driver or RAID driver. If the terminal uses IDE mode, follow the Windows installer to complete the installation.

4. The “Load Driver” window appears. Push the “Browse” button to specify the directory for SATA driver or RAID driver. Then, the Windows installer will select correct driver for SATA configuration.

AHCI : “Intel(R) Desktop/Workstation/Server Express Chipset SATA AHCI Controller” RAID : “Intel(R) Desktop/Workstation/Server Express Chipset SATA RAID Controller” Subsequently, follow the instructions of the Windows installer to complete the installation.

38

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3.2. Intel Chipset Software Installation Run “infinst_autol.exe” in the “ST-M30WinV1xxx\32bit\1_Chipset” folder in the Driver kit for 32bit OS. Or, run “infinst_autol.exe” in the “ST-M30WinV1xxx\64bit\1_Chipset” folder in the Driver kit for 64bit OS. *xxx means version number of driver kit. And, please run it with “Run as Administrator”. 1. Setup files will be extracted. Then, click on the “Next” button when the following window appears.

2. The “License Agreement” window appears. Confirm the contents. Click on the “Yes” button to agree.

39

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3. The “Readme File Information” window appears. Click on the “Next” button to start the installation.

4. The “Next” button will be enabled when installation is complete. Please click on the “Next” button to proceed.

40

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

5. Next, the installer will prompt for system reboot. Select “Yes, I want to restart this computer now” option, and then click on the “Finish” button to reboot POS Terminal.

41

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3.3. Intel Graphic Accelerator Driver Installation Run the “Win7Vista.exe” in the “ST-M30WinV1xxx\32bit\2_Graphic\2_Win7” folder in the Driver kit for 32bit OS. Or, run the “Win7Vista_64.exe” in the “ST-M30V1xxx\64bit\2_Graphic\” folder in the Driver kit for 64 bit OS. *xxx means version number of driver kit. 1. Please click on the “Next” button to continue.

2. The following window appears when extraction is complete. Please click on the “Next” button.

42

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3. The “License Agreement” window appears. Confirm the contents. If agree, click on the “Yes” button.

4. The “Readme File Information” window appears. Click on the “Next” button.

43

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

5. The “Next” button will be enabled when installation is complete. Please click on the “Next” button to proceed.

6. Next, the installer will prompt for system reboot. Select “Yes, I want to restart this computer now” option, and then click on the “Finish” button to reboot POS Terminal.

44

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

7. After rebooting the POS Terminal, user can use Device Manager to confirm the graphic driver has been installed. Make sure that “Intel(R) HD Graphics Family” is registered under the “Display adapters” category.

45

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3.4. Network Driver Installation 3.4.1. Intel Network Driver installation Run “PROWin32.exe” in the “ST-M30WinV1xxx\32bit\3_LAN\1_Intel\2_Win7” folder in the Driver kit for 32bit OS. Or, run the “PROWin64.exe” in the “ST-M30WinV1xxx\64bit\3_LAN\1_Intel” folder in the Driver kit for 64 bit OS. *xxx means version number of driver kit. 1. Please click on the “Next” button to continue.

2. The ”License Agreement” window appears. Confirm the contents. Select the “I accept the terms in the license agreement” option and click on the “Next” button to agree.

46

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3. The “Setup Options” window appears. Click on the “Next” button with default condition when it’s not need to install some option to terminal.

4. Next, click on the “Install” button to start the installation.

47

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

5. The following window appears when the installation is complete. Click on the “Finish” button to complete the installation. Note: Reboot the computer manually.

6. User can use Device Manager to confirm the network driver has been installed. Make sure that “Intel(R) 82579LM Gigabit Network Connection” is registered under the “Network adapters” category.

48

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3.4.2. Realtek Network Driver installation Run the “setup.exe” application located in “ST-M30WinV1xxx\32bit\3_LAN\2_Realtek” folder of the Driver kit for 32bit OS. Or, run the “setup.exe” application located in “ST-M30WinV1xxx\64bit\3_LAN\2_Realtek” folder of the Driver kit for 64bit OS. *xxx means version number of driver kit. 1. The setup window appears when the “setup.exe” starts running. Please click on the “Next” button. The file is in the unzipped folder.

2. Please click on the “Install” button to start the installation.

49

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3. Next, following window will appears when the installation is complete. Click on the “Finish” button to close window.

4. User can use Device Manager to confirm the network driver has been installed. Make sure that “Realtek PCIe GBE Family Controller” is registered under the “Network adapters” category.

50

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3.5. Realtek Audio Driver Installation (Windows 7 only) By default, POSReady 7 has been installed with Realtek Audio Driver. No additional installation is required in this case. Run the “Vista_Win7.exe” in the “ST-M30WinV1xxx\32bit\4_Audio\2_Win7” folder in the Driver kit for 32bit OS. Or, run the “64bit_Vista_Win7.exe” in the “ST-M30WinV1xxx\32bit\4_Audio” folder in the Driver kit for 64bit OS. *xxx means version number of driver kit. 1. Please click on the “Next” button to start the installation.

51

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

2. Next, the installer will prompt for system reboot when the installation is complete. Select “Yes, I want to restart my computer now” option, and then click on the “Finish” button to reboot POS Terminal.

3. User can use Device Manager to confirm the audio driver has been installed. Make sure that “Realtek High Definition Audio” is registered under the “Sound, video and game controllers” category.

52

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3.6. Setup for Display Each display type has its own supplementary setup document. For TFTST-A20 and TFTST-B20, please refer to “TFTST-A20, TFTST-B20 Setup Guide” which contains: · ·

Installation for ELO (Tyco) Touch panel driver Installation for the driver of other optional equipment

The display setup guide describes the procedures and pre-cautions in setting up each display drivers.

53

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

4.

JEA-02533

Setup for RAID

4.1. Setup for RAID HDD If the POS Terminal uses RAID mode, please refer to the following procedure. 1. Boot up the terminal and press “Ctrl” key and “I” key to execute the Configuration Utility before BIOS window is appeared. Intel(R) Rapid Strag e Technology - Option ROM - 10.1.0.1008 Copyrig ht(C) 2003-10 Intel Corporation. All Rights Reserved. RAID V olum es : None defined. Physical Devices: Port Device Model Serial # 0 W DC WD400JD-22L S W D-WM AM9UF 56127 1 W DC WD400JD-23L R W D-WM AMA A698578 Press to enter Configuration Ut ility...

Size Type/Status(Vol ID ) 37.2GB Non-RAID Disk 37.2GB Non-RAID Disk

2. Please select “1. Create RAID Volume” menu to create RAID HDD. Intel(R) Rapid Storage Technology - Option ROM - 10.1.0.1008 Copyright(C) 2003-10 Intel Corporation. All Right Res erved. [ MAIN MENU ] 1. Create RAID Volum e

3, Reset D isks to N on-RAID

2. Delete RA ID Volume

4. Recovery Volum e Options 5. Ex it

[ DISK/V OL UME INFOR MATION ] RA ID Volumes: N one defined. Physical Devices: Port Device M odel

Serial #

0

WDC W D400JD -22LS

WD-W MAM 9UF56127

37.2GB N on-RAID D isk

1

WDC W D400JD -23LR

WD-W MAM AA698578

37.2GB N on-RAID D isk

[↑ ↓]-Select

Size Type/Status(Vol ID)

[ESC]-Exit

[ENTER ]-Select M enu

54

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3. Select RAID level and change the HDD name if needed. To create the volume, select “Create Volume” and press “Enter”. Then, press “Y” key to agree when confirmation window appears. Ex) RAID0 mode Intel(R) Rapid Storage Technology - Option ROM - 10.1.0.1008 Copyrig ht(C) 2003-10 Intel Corporat ion. All R ight R eserved. [ CREATE VOLUME M ENU ] Nam e : RA ID Level : Disks : Strip Siz e :

Volume0 RAID0(Stripe) Select Disks 128KB

Capacity :

74.5

Sync :

N/A

GB

Create Volume [ HELP ] Enter a unique volume nam e that has special characters and is 16 charcters or less .

[↑↓ ]-Select

[ESC]-Exit

[ENTER ]-Select M enu

Ex) RAID1 mode Intel(R) Rapid Storage Technology - Option ROM - 10.1.0.1008 Copyrig ht(C) 2003-10 Intel Corporat ion. All R ight R eserved. [ CREATE VOLUME M ENU ] Nam e : RA ID Level : Disks : Strip Siz e :

Volume0 RAID1(M irror) Select Disks N/A

Capacity :

37.3

Sync :

N/A

GB

Create Volume

[ HELP ]

Enter a unique volume nam e that has special characters and is 16 charcters or less .

[↑↓ ]-Select

[ESC]-Exit

[ENTER ]-Select M enu

55

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

4. The utility will return to main window when RAID creation complete. Hence, please press “Esc” key to exit window. Ex) RAID0 mode Intel(R) Rapid Storage Technology - Option ROM - 10.1.0.1008 Copyright(C) 2003-10 Intel Corporation. All Right Res erved. [ MAIN MENU ] 1. Create RAID Volum e

3, Reset D isks to N on-RAID

2. Delete RA ID Volume

4. Recovery Volum e Options 5. Ex it

[ DISK/V OL UME INFOR MATION ] RA ID Volumes: ID

Nam e

Level

Strip

0

Volume0

RAID0(Stripe)

128KB

Size Status

Bootable

74.5GB N ormal

Yes

Port Device M odel

Serial #

0

WDC W D400JD -22LS

WD-W MAM 9UF56127

37.2GB M ember D isk(0)

1

WDC W D400JD -23LR

WD-W MAM AA698578

37.2GB M ember D isk(0)

[↑ ↓]-Select

Size Type/Status(Vol ID)

[ESC]-Exit

[ENTER ]-Select M enu

Ex) RAID1 mode Intel(R) Rapid Storage Technology - Option ROM - 10.1.0.1008 Copyright(C) 2003-10 Intel Corporation. All Right Res erved. [ MAIN MENU ] 1. Create RAID Volum e

3, Reset D isks to N on-RAID

2. Delete RA ID Volume

4. Recovery Volum e Options 5. Ex it

[ DISK/V OL UME INFOR MATION ] RA ID Volumes: ID

Nam e

Level

Strip

Size Status

0

Volume0

RAID1(M irror)

N /A

37.3GB N ormal

Bootable

Port Device M odel

Serial #

0

WDC W D400JD -22LS

WD-W MAM 9UF56127

37.2GB M ember D isk(0)

1

WDC W D400JD -23LR

WD-W MAM AA698578

37.2GB M ember D isk(0)

[↑ ↓]-Select

Yes

Size Type/Status(Vol ID)

[ESC]-Exit

[ENTER ]-Select M enu

56

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

5.

JEA-02533

Optional Settings and Restriction

5.1. Optional settings procedure 5.1.1. USB-HUB Power Management To configure the USB-HUB power management: 1. From Device Manager, select the property of the “USB Root Hub” under the “Universal Serial Bus controllers”.

57

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

2. Under the "Power Management" tab, un-check the "Allow the computer to turn off this device to save power" check box to disable the power management, click the “OK” button to save the change. Please take note that this option is turned on by default. And, repeat the steps for all the “USB Root Hub”.

58

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

5.1.2. Wake On LAN Settings The LAN controller of ST-M30 supports Wake On LAN feature. By default, it is disabled. In order to enable the Wake On LAN function, perform the following settings. 1. Right click the Local Area Connection icon and select ‘Properties’. Click “Configure...” button under ‘Properties’ window.

59

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

2. For Intel Network Connection, under the “Power Management” tab, select the “Wake on Magic Packet from power off state” check box under “Wake on LAN” section and click the “OK” button to save the changes. Note: Currently, only “Wake on Magic Packet from power off state” is supported on ST-M30.

60

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3. For Realtek Network Connection, under the “Power Management” tab, select the “Allow this device to wake the computer” check box and the “Only allow a magic packet to wake the computer” check box. Next, click the “OK” button to save the changes. Note: Currently, only “Wake on Magic Packet from power off state” is supported on ST-M30.

61

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

5.1.3. Dual Display connection combinations list ST-M30 supports the following types of display: - TFTST-B20 (VGA - ELO (Tyco) Touch Panel) - Display via DVI interface. There are some restrictions in using dual display functionality, please refer to the tables below for supported settings. [Dual display support table without touch panel functionality] TFTST-B20 DVI monitor (VGA) TFTST-B20 Support (VGA) DVI monitor Support Support: can configure dual display setting with Intel graphic driver is installed. [Dual display support table with touch panel functionality] TFTST-B20 DVI monitor (VGA) TFTST-B20 Support (VGA) with limitation DVI monitor Support with limitation Support with limitation: touch panel functionality will work with limitation if dual display is configured. (e.g. VGA screen might not be able to wake on touch from hibernation in dual display setting)

62

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

5.2. Limitation 5.2.1. Limitation for Wake up by USB keyboard / mouse from S3 By default, OS can go to S3 (standby) mode and can wake up by using USB keyboard and mouse. However, there is some restriction for wake-up by USB keyboard and mouse from S3 in Windows Xp, WEPOS, and POSReady2009. In order to enable wake-up by USB keyboard and mouse from S3, additional registry key setting is required. For more details, please refer to the following Microsoft web page. http://support.microsoft.com/kb/841858/en Registry key setting: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\usb "USBBIOSx"=DWORD:00000000 Aside from registry setting, the following setting also required to enable wake-up by USB keyboard and mouse from S1/S3. ·

USB Keyboard setting: o Go to Control Panel->System->Device Maneger->Keyboard -> HID Keyboard Device->Power Management o Select “Allow this device to bring the computer out of standby” option.

·

USB mouse setting: o Control Panel->System->Device Maneger->Keyboard -> HID compliant mouse->Power Management o Select “Allow this device to bring the computer out of standby” option.

63

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

5.2.2. Extended display mode in POSReady 2009 For POSReady2009 with Intel Graphic Driver is installed, BSOD (blue screen error) will happen if user want to change from "Extended Desktop" mode to other mode for example "Single Display", "Twin" or "Dual Display Clone" mode, This is due to the restriction of POSReady2009, please refer to the following web page for more details. (Microsoft HP: http://support.microsoft.com/kb/959252) To prevent this problem, user needs to download and install the patch from above Microsoft link.  Download the patch file ” WindowsXP-KB959252-v2-x86-ENU.exe” for Windows XP, x86 edition, and install to the machine. After installing the patch, the Extended display mode can be displayed and changed to other mode correctly.

64

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

5.2.3. Limitation of Windows Time Service In normal Windows system, Windows Time Service adjusts system time automatically via network with NTP protocol. Normally, this service functions correctly in the environment that has Internet access. In an environment without Internet access, Windows Time Service will not be able to set the time correctly. Hence, it is recommended to stop and disable this service when using ST-M30 in the environment without Internet access. This service can be stopped by the following steps: 1. Open “Date and Time” from “Control Panel”. Under the “Internet Time” tab, click on the “Change settings…” button.

2. Uncheck the “Synchronize with an Internet time server” check box.

65

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

3. Next, open “Administrative Tools” from “Control Panel”.

4. Then, open the “Services” from Administrative tools.

66

Windows Setup Guide for ST-M30 Toshiba TEC Corporation

JEA-02533

5. Open the property of the "Windows Time" from displayed services.

6. Select the “General” tab and change the “Startup type” value to “Disabled”.

67