Platinum™ IP3 PX-RES Release Notes Version 1.6.11 Download Filename: PX-RES_1_6_11.zip Release Date: 2016-05-09
The Platinum™ IP3 PX-RES Resource card is a control module with software and hardware components that control communications between the different processing modules (input, output, crosspoint) in all Platinum™ IP3 frames, and in Platinum series 9RU, 15RU, and 28RU frames.
1.6.11 RELEASE SUMMARY This release contains one fix.
Fixes and Improvements •
124784: Resolved an issue with system expansion routing failure caused by incomplete (PRC) Module notification messages sent by the PX-RES Module.
•
Support for Platinum SX Hybrid Multiviewer Modules
Known Issues •
121818: In some instances, video switching is delayed by 1 frame.
•
126320: In case of a PX-RES failover, there is an approximately 20 second signal outage for Platinum SX Hybrid PIPs.
UPGRADING FIRMWARE •
Refer the Platinum™ IP3 Controller 1.5.1 User Manual and Upgrade Instructions document for information on upgrading PX-RES firmware. The user manual is integrated with the Platinum™ IP3 Controller firmware, and can be accessed through the Help link in the Web UI. It can also be downloaded from the Imagine Communications website at http://www.imaginecommunications.com/
Release 1.6.3 New Features •
Support for the Platinum™ IP3 15 RU Frame
Fixes and Improvements •
105913: Resolved an issue with performing firmware activation when the PX-RES was in failsafe mode
•
92605: Resolved an issue with incorrect status reporting when upgrading single/dual PX-RES modules
•
106777: Resolved an issue where in case of PX-RES in a Platinum frame with a Platinum SX Pro Multiviewer module, routing of PIPs was always 8-ports, even if the Multiviewer Mode parameter was set to 16-ports.
•
116141: Resolved an issue with additional parameters in new IO module firmware not shown after an upgrade.
•
115724: Resolved an issue with a leading 'space' character in the License Key field in IP3 UI
•
119486: Resolved an issue with incorrect reporting of IO module firmware version.
•
120108: Resolved an issue with the Video Switch Point being out of specification for 1080i50 and 1080p50 signals with sync reference as PAL.
•
120015: Resolved an issue with the Video Switch Point of the top 512 ports being out of specification if Sync 2, 3 or 4 were selected.
•
120054: Resolved an issue with the router output generating a high level of noise when changing the source signal EQ from Bypass to On
•
121623: Resolved an issue with the Input module Sync Selection delaying the route switching up to 3 frames.
•
121653: Resolved an issue with PX-RES failing to detect an ATDM module when power cycling a specific zone associated with the module
•
121712: Resolved an issue where in a redundant crosspoint scenario, routes were lost after Crosspoint module 1 was removed and the PX-RES firmware then activated
Platinum™ IP3 PX-RES Release Notes Version 1.6.11 Download Filename: PX-RES_1_6_11.zip Release Date: 2016-05-09 •
123096: Resolved an issue with the PT-HS-IB+ ‘Signal Presence’ parameter showing all 0s after rebooting PX-RES even though signals were present
•
123236: Resolved an issue with the IP3 tieline controller showing incorrect route status after PX-RES failover
•
123564: Resolved an issue with PX-RES failing to route audio channels on PX-FS-OBG modules when the Sync Select parameter was set to Sync 2, 3 or 4
•
118174: Resolved an issue with changes to module parameters not getting synchronized over to the standby PX-RES if the slot above the IO module was empty.
•
123591: PX-FS-OBG parameters revert to default when the PX-RES is rebooted or failed over. Note: This error will occur when upgrading earlier firmware versions to release 1.6.3. The user must manually reconfigure the following modules after an upgrade: PX-HSR8CMX8C-OBG, PX-HSR8OMX8O-OBG, PX-HSRMX8C2D-OBG, and PX-HSRMX8O2D-OBG.
Release 1.5.0 New Features •
Support for PX-RES in Platinum™ 9 RU and 15 RU frames. Note: Ensure IP3 Controller version 1.3.3 is used.
Note: Refer to the Module compatibility matrix at the end of this document for details on supported and unsupported PT/PX modules when PX-RES is used a Platinum frame and an IP3 frame.
Fixes and Improvements •
109388 - Resolved an issue with PIPE parameters reverting to default values after an upgrade.
•
109858: Upgrading multiple IO modules simultaneously can occasionally fail.
Release 1.4.3 New Features •
Support for PT-HSRAEC-OM Platinum Output Monitoring Modules
•
Support for PX-HSRMX8C2D-OBG and PX-HSRMX8O2D-OBG Platinum IP3 Frame Sync and Mux Output Modules
Fixes and Improvements •
107741: Resolved an issue with the Active LED indicator on the PX-FRONT-FAN module not reactivating properly after a single zone power cycle.
Release 1.4.1 Fixes and Improvements •
105970: Resolved an issue with the PX-RES synchronization process failing during firmware activation
•
106009: Resolved an issue where a soft failover of the PX-RES module caused expansion signals to be replaced by local signals for around 10 seconds
Release 1.4.0 New Features •
Support for the PX-HSRAEC-OM output monitoring module.
•
Support for PX-HSR8CMX8C-OBG and PX-HSR8OMX8O-OBG frame sync and mux output modules.
•
PX-RES firmware activation progress now displayed.
Platinum™ IP3 PX-RES Release Notes Version 1.6.11 Download Filename: PX-RES_1_6_11.zip Release Date: 2016-05-09
Fixes and Improvements •
90953: The PX-RES module did not boot up correctly when only the top half of the router was powered. This has been fixed.
•
101530: Resolved an issue with false signal loss alarms generated for the PX-HSR16C-OBG module when a valid signal was presented at the output.
•
95648: Adjusted the switch point to be within the switching line.
•
87376: Resolved an issue with incorrect ambient temperature reading.
•
79658: Resolved an issue with Disabled alarms momentarily reported as active after module upgrade reboots.
•
82085: Resolved an issue with ‘Active’ parameters occasionally displaying incorrect values after an upgrade.
•
82512: Resolved an issue with Module XML files not being synchronized over to the standby PX-RES after an upgrade.
•
71353: Resolved an issue with IO Expansion routes that took nearly 15s for remote signals to route through to local outputs.
•
103746: Resolved an issue with occasional loss of routes after PX-RES firmware activation.
•
82971: Resolved an issue where establishing a PRC connection to the PX-RES while in the failsafe mode caused the PX-RES to crash.
Release 1.3.8 New Features •
Rebranded. No other changes.
Release 1.3.6 Fixes and Improvements •
100774: Frame IDs were incorrectly read at startup. This has been fixed.
Release 1.3.2 Fixes and Improvements •
100777: Previously, the PT-HSRMX-OBG output module was always detected in failsafe mode. This has been fixed.
Release 1.3 New Features •
Support for Platinum SX Pro Multiviewer Modules (PX-SXP).
Release 1.2 Fixes and Improvements •
79648: With HView Designer, rebooting the Multiviewer sometimes cleared out the UMD labels on the Monitor. This has been fixed.
•
80981: With HView Designer, power cycle occasionally caused the Monitor UMD to display static text, and required a reboot. This has been fixed.
•
81056: With HView SX Pro, LRC labels were not updated with imported layouts, and required a reboot. This has been fixed.
Platinum™ IP3 PX-RES Release Notes Version 1.6.11 Download Filename: PX-RES_1_6_11.zip Release Date: 2016-05-09
Release 1.1 Fixes and Improvements •
72523: When a destination was in a locked or protected state, and a route could not be switched, PX-RES did not send back a XY status message. This has been fixed.
•
73196: Setting the Sync Mode parameter to Standard or Advanced did not take effect. This has been fixed.
•
73384: Failover of the Video Crosspoint (XPT) Module occasionally caused the firmware to crash. This has been fixed.
•
71983: Frame alarms were disabled by default.
(PT) / (PX) MODULE COMPATABILITY MATRIX Module
PX-RES in Platinum
PX-RES in IP3
Module
(PX) Input Modules
(PT) Input Modules
PX-HSR9C-IBG
PT-ADCT-IB
PX-HSR9C1D-IBG
PM-ADCT-IB
PX-HSR9O-IBG
PT-AEBT-IB
PX-HSR9O1D-IBG
PM-AEBT-IB
PX-HSR8C-IBG
PT-AECT-IB
PM-HSR8C-IBG
PM-AECT-IB
PX-HSR2C2D-IBG
PT-DEC-IB
PX-HSR1C1D-IBG
PM-DEC-IB PT-FSDMX-IBG/ PT-FSDMXO-IBG PT-FSDX8C1D-IBG PT-FSDX8O1D-IBG PT-HS-IB+ PT-HSO-PIN-IB+ (PT-HSO-IB+) PT-HSR1D-IBG/ PT-HSR2D-IBG PT-HSR8C1D-IBG PT-HSR8O1D-IBG PT-MADI4C-IBG/ PT-MADI4O-IBG
(PX) Output Modules
(PT) Output Modules
PX-HSR16C-OBG
PT-AEBT-OB
PX-HSR8C2D-OBG
PM-AEBT-OB
PX-HSR8O2D-OBG
PT-AECT-OB
PX-HSR16O-OBG
PM-AECT-OB
PX-HSRSXP2D-OBG
PT-DACT-OB
PX-HSRMX8C2D-OBG
PM-DACT-OB
PX-HSRMX8O2D-OBG
PT-ENC-OB
PX-HSR8CMX8C-OBG
PM-ENC-OB
PX-HSR8OMX8O-OBG
PT-HSR-OB+ PM-HSR-OB+ PT-HSR-OBG+
PX-RES in Platinum
PX-RES in IP3
Platinum™ IP3 PX-RES Release Notes Version 1.6.11 Download Filename: PX-RES_1_6_11.zip Release Date: 2016-05-09 PM-HSR-OBG+/ PT-HSRO-OBG+ PT-HSRMX8C-OBG PT-HSRMX8O-OBG PT-MADI4C-OBG/PT-MADI4O-OBG PT-SR-OBG+/ PM-SR-OBG+ (PX) Frame Modules
(PT) Frame Modules
PX-576x1024-3G
PM-64x64-3G9
PX-ALARM-ATDM
PM-128x128-3G9
PX-ALARM-DATA
PT-128x256-3G15
PX-ATDM64-X28
PT-ALARM
PX-FRONT-FAN
PM-ATDM16-X9
PX-HSRAEC-OM
PT-ATDM16-X15
PX-RES
PT-HSRAEC-OM PT-SYNC
Multiviewer Modules PX-SXP-16x3 PX-SXP-32x6 PX-SXP-64x6 PX-SXP-16x3-O PX-SXP-32x6-O PX-SXP-64x6-O PX-SXP-16x3-OD PX-SXP-32x6-OD PX-SXP-64x6-OD