pH
pH Meters pH Meters Handheld pH meters
Electrodes
Portable pH meters
Accessories
Laboratory pH meters
pH The pH is a measure of the acidity or alkalinity of a sample. A pH of 7 means that the sample is neutral and reacts neither like an acid nor like a base. Fresh tap water, for example, is approximately neutral. Samples with a pH of less then 7 are acidic, e.g. lemonade, lemon juice or hydrochloric acid. In practice pH values down to below -1 are known. An alkaline sample has a pH of more than 7, e.g. stale tap water, water containing detergents or soda lye. The pH scale reaches values of more than 15.
orange juice
sea water
Cola
ammonia
0.4% HCI
-1
0
1
2
milk
3
acidic
4
5
6
7
0.4% NaOH
8
neutral
9
10
11
12
13
14
15
basic/alkaline
The more the pH differs from 7, the more aggressive the sample. For each pH unit the acidic or basic effects increase by a factor of 10. pH can be measured by electrochemical pH measuring systems, indicator strips, indicators or colorimeters. Of these only electrochemical measurements provide accurate results. Measurements are made with an electrode. The electrode is an electrochemical sensor which consists of a measuring electrode and a reference electrode. The voltage at a membrane alters according to the pH of the sample solution. The electrodes normally used today are constructed so that the voltage at the membrane is 0 mV when the pH is 7. The more the pH differs from 7, the larger the voltage signal produced. The pH meter uses this signal to calculate the pH.
Literature 26
Further information on this subject can be requested from WTW:
pH handbook Application reports Offprints
Wissenschaftlich-Technische Werkstätten GmbH & Co. KG · Dr.-Karl-Slevogt-Straße 1 · 82362 Weilheim · Germany · Tel.: +49 (0) 881-1 83-0 · Fax: +49 (0) 881-62 53 9
Laboratory & Field pH
General Features
pH Meters
ORP
pH meters for every application
Classic Robust, impact-resistant, waterproof, transportable, pH depth measurements down to 100 m
32
Laboratory pH meters
inoLab® top quality in 3 stages - simple and reliable - compact and communicative - flexible and powerful
34
Electrodes
favorably priced, universal, reliable
38
pH meter accessories ❍ Calibration and maintenance supplies - for pH measurement - for maintenance and cleaning ❍ Temperature sensors ❍ Recommended accessories - stands and electrode holders - stirrers - measuring and storage vessels
Portable pH meters
For documentation
Software, printer and accessories
44 45
180 46
Colony Counter
ORP measurements
42 42
Oxygen (D.O.)
Portable pH meters
Handheld pH meters
Conductivity
28
MultiParameter
Quality in a set of three - Simple to operate model - Time-proven model with memory function - All-rounder with interface
BOD
Handheld pH meters
ISE
from page
Respiration Sample Preparation
Model
from page 48
Multi-parameter instruments
96
Software, Printers
Turbidity
Ion meters
Photometry
Other instruments with built-in pH measurement
Customer Service
Laboratory pH meters
Wissenschaftlich-Technische Werkstätten GmbH & Co. KG · Dr.-Karl-Slevogt-Straße 1 · 82362 Weilheim · Germany · Tel.: +49 (0) 881-1 83-0 · Fax: +49 (0) 881-62 53 9
27
pH General Information about handheld pH meters can be found on pages 14 - 17.
pH Meters Handheld pH Meters pH 315i, pH 330i and pH 340i
NEW
Features Handy Waterproof Low-power system allows continuous operation for up to 3000 h Easy to use GLP-conform
Pocket-sized precision WTW handheld pH meters are dustproof and waterproof, they can also be submersed. The large and clear multifunctional display allows the values to be read off safely and comfortably. The silicone keypad with tactile response ensures simple operation. Automatic switch-off combined with an energysaving system permits continuous operation for up to 3000 h.
Complete in SET
28 Wissenschaftlich-Technische Werkstätten GmbH & Co. KG · Dr.-Karl-Slevogt-Straße 1 · 82362 Weilheim · Germany · Tel.: +49 (0) 881-1 83-0 · Fax: +49 (0) 881-62 53 9
Laboratory & Field General Features
Handheld pH Meters
pH 315i, pH 330i, pH 340i
ISE
ORP
pH
handy · waterproof · GLP-conform
WTW handheld pH meters are available in three versions:
Oxygen (D.O.)
pH 315i:
MultiParameter
Conductivity
Very robust and waterproof battery-operated pH/mV meter. Measuring errors are avoided by the silicone keypad with only 5 keys and a simplified calibration method with automatic buffer recognition and display for standard buffers. AutoRead also ensures stable and reproducible results.
pH 330i:
Respiration Sample Preparation
BOD
Very robust and waterproof battery-operated pH/mV meter with built-in datalogger, realtime clock, GLP-supporting functions, display for calibration switchable between pH and mV. MultiCal® automatic calibration with buffer recognition, automatic temperature compensation.
pH 340i:
IP 66 IP 67
3 Year Warranty
Wissenschaftlich-Technische Werkstätten GmbH & Co. KG · Dr.-Karl-Slevogt-Straße 1 · 82362 Weilheim · Germany · Tel.: +49 (0) 881-1 83-0 · Fax: +49 (0) 881-62 53 9
Customer Service
Software, Printers
Turbidity
pH 315i
Photometry
Colony Counter
Very robust and waterproof pH/mV meter for battery or mains supply operation with built-in datalogger, real-time clock, GLP-supporting functions, display for calibration switchable between pH and mV. MultiCal® automatic calibration with buffer recognition, automatic temperature compensation and additional RS 232 analog and digital output.
29
pH
Technical Data Model
pH 315i
pH 330i
Measuring range/ resolution
pH
-2.00 … +16.00 pH
pH
mV
-1999 … +1999 mV
Accuracy (± 1 digit)
Temp. -5.0 … +105.0 °C
-2.000 ... +19.999 pH -2.00 … +19.99 pH mV -999.9 ... +999.9 mV -1999 … +1999 mV Temp. -5.0 ... +105.0 °C
pH
pH
±0.01 pH
pH 340i
mV ±0.3 mV at +15 °C … +35 °C Temp. ±0.1 K
±0.005 pH at +15 … +35 °C mV ±0.3 mV at +15 °C … +35 °C Temp. ±0.1 K
pH
±0.003 pH at +15 … +35 °C mV ±0.2 mV Temp. ±0.1 K
Temperature compensation
Automatic for pH electrodes with built-in temperature sensor, TFK 325 / Pt 1000
Automatic for pH electrodes with built-in temperature sensor, TFK 325 / Pt 1000 manual by entering sample temperature
Display
LCD display 60 x 45 mm visible area, simultaneous display of measurement, temperature, special characters
Sensor evaluation
Depends on calibration results, shown on display
Calibration alarm
–
1 ... 999 days, adjustable
AutoRead
For reproducibility better than 0.05 pH
For reproducibility better than 0.02 pH
Calibration
Simplified 1, 2 or 3-point calibration with automatic buffer recognition AutoCal automatic 3-point calibration with DIN buffers
MultiCal® automatic calibration: AutoCal automatic 2 or 3-point calibration with DIN buffers AutoCal-TEC automatic 2 or 3-point calibration with WTW technical buffers ConCal® conventional 1-point calibration with any buffers
Calibration protocol
–
GLP-conform calibration protocol; last protocol stored in memory
Data storage
–
500 data sets (measurement, temperature, date/time, identity no.); time-controlled storage at intervals 5 s ... 60 min, non-volatile data storage (even when changing batteries)
Data output
Via display
Via display
Via display or interface, time-controlled at intervals 5 s ... 60 min
Interface
–
–
Self-configuring as analog output according to electrode potential, i.e. 50 - 60 mV/pH unit, or RS 232 bi-directional interface
Operating period
3000 hours with normal 4 x 1.5 V batteries (AA) with AutoSwitchOff after 1 h (except logger operation)
Protection type
IP 66 and IP 67 to IEC 529
Dimensions
172 x 80 x 37 mm (H x B x D)
Weight
Approx. 300 g
Certified to
CE, TÜV/GS, UL and/or cETLus, CUL
Warranty
3 years
3000 hours continuous operation with batteries, optional mains power supply, no rechargeable batteries
30 Wissenschaftlich-Technische Werkstätten GmbH & Co. KG · Dr.-Karl-Slevogt-Straße 1 · 82362 Weilheim · Germany · Tel.: +49 (0) 881-1 83-0 · Fax: +49 (0) 881-62 53 9
Laboratory & Field General Features
Handheld pH Meters
SET Equipment
pH
Each handheld pH meter is available in a complete application-oriented set
Basic equipment:
Robust and waterproof handheld pH meter, for battery operation
2A10-100
pH 330i
Robust and waterproof handheld pH meter with datalogger, for battery operation
2A20-100
pH 340i
Robust and waterproof handheld pH meter with datalogger and serial interface, for battery operation
2A30-100
pH 340i
Robust and waterproof handheld pH meter with datalogger and serial interface, for battery or mains operation
2A30-110
Ordering Information SETs Handheld pH meter, with electrode, professional case and accessories
2A10-101
pH 330i
Handheld pH meter, with electrode, professional case and accessories
2A20-101
pH 340i
Handheld pH meter, with electrode, professional case and accessories
2A30-101
pH 340i
Handheld pH meter with mains power supply, with electrode, professional case and accessories
2A30-111
Colony Counter
Order No.
pH 315i
SenTix® electrodes – please select one pH combination electrode, gel electrolyte pH combination electrode, gel electrolyte and temperature sensor TFK 325/HC pH combination electrode with built-in temperature sensor, gel electrolyte SenTix® 81 pH combination electrode with built-in temperature sensor and measuring vessel for drinking water
SET ordering example pH 315i + SenTix® 41 electrode
1 1
1
2 T
2A10-101
2
Note: other electrodes in SET or instrument versions for 120 VAC/60 Hz are available on request.
Customer Service
Please refer to page 38 for electrodes and page 42 for further accessories.
Photometry
SenTix® 21 SenTix® 21 SenTix® 41 Drinking water kit
Turbidity
Handheld pH Meters SETs
BOD
Order No.
pH 315i
Software, Printers
Handheld pH Meters
Respiration Sample Preparation
Ordering Information Handheld pH Meters
MultiParameter
Conductivity
Oxygen (D.O.)
ISE
ORP
• Professional case with built-in measuring set-up and separate compartment for electrode and accessories • Instrument including batteries • Electrode as chosen • STH 320 stand • WTW technical buffers pH 4.01 - 7.00 • KCl solution (3 mol/l) • Beaker • Plug-in power supply (only pH 340i) • Operating instructions
Wissenschaftlich-Technische Werkstätten GmbH & Co. KG · Dr.-Karl-Slevogt-Straße 1 · 82362 Weilheim · Germany · Tel.: +49 (0) 881-1 83-0 · Fax: +49 (0) 881-62 53 9
31
pH General Information about portable pH meters can be found on pages 18 – 19.
pH Meters Portable pH Meters ProfiLine pH 197 and ProfiLine pH 197-S
Features
3 Year Warranty
IP 66 IP 67
Robust
WTW portable pH meters
Shockproof
The WTW pH meters of the ProfiLine pH 197 series are both hose-proof (IP 66) and submersible (IP 67. They convince because of their high degree off operator comfort and safe operator guidance via the large multifunctional display. They are equipped with a carrying/support handle and carrying strap as standard.
Waterproof Portable Reliable Standard pH measurement and pH measurement at depths down to 100 m
The portable pH meters are available in 2 versions:
ProfiLine pH 197: Indestructible pH/mV meter. With rechargeable battery and mains operation, measurement storage, GLP-supporting functions, MultiCal®‚ automatic calibration, automatic temperature compensation... Also suitable for pH depth measurements down to 100 m with TA 197 pH depth armature.
ProfiLine pH 197-S: As ProfiLine pH 197 but with additional analog recorder outputs corresponding to display for pH/mV and temperature values.
Accessories for pH measurement at depths down to 100 m pH depth armature TA 197 pH with built-in temperature sensor, up to 100 m cable with waterproof plug (IP 67), steel armoring (material no. 1.4571) with screw-off protective hood, pressure-resistant to max. 10 bar, fits into 2” boreholes, without combination electrode (see page 33).
32 Wissenschaftlich-Technische Werkstätten GmbH & Co. KG · Dr.-Karl-Slevogt-Straße 1 · 82362 Weilheim · Germany · Tel.: +49 (0) 881-1 83-0 · Fax: +49 (0) 881-62 53 9
ProfiLine pH 197
Measuring range/ resolution
pH mV Temperature
-2.00 ... +16.00 pH -1250 ... +1250 mV -5.0 ... +99.9 °C
ProfiLine pH 197-S
Accuracy (± 1 digit)
pH mV Temperature
±0.01 pH ±2 mV ±0.1 K
Temperature compensation
Automatic for pH electrodes with built-in temperature sensor TFK 325 / Pt 1000 manual by entering sample temperature
Display
LCD display 60 x 35 mm visible area, simultaneous display of measurement, temperature, special characters
AutoRead
For reproducibility better than 0.02 pH
Calibration
MultiCal® automatic calibration AutoCal automatic 2-point calibration with DIN buffers AutoCal-TEC automatic 2-point calibration with WTW technical buffers ConCal® conventional 1 or 2-point calibration with any buffers
Data storage
Ring memory for 50 pairs of measurements with data protection
Data output
Via display or interface
Interface
Unidirectional RS 232 interface
Operating time
Continuous operation from mains supply; 1500 hours with rechargeable batteries with AutoSwitchOff after 1 h
Protection type
IP 66 and IP 67 to IEC 529
Dimensions
230 x 185 x 90 mm (B x D x H)
Weight
Approx. 1.5 kg
Certified to
CE, TÜV/GS, UL, CUL
Warranty
3 years
Oxygen (D.O.)
ISE
ORP
pH
Model
General Features
Technical Data
Order No.
ProfiLine pH 197
Robust, waterproof, submersible pH/mV meter
100 350
ProfiLine pH 197-S
As ProfiLine pH 197, but additionally with 2 analog recorder outputs
100 315
Note: 120 VAC / 60 Hz versions on request
Standard pH combination electrode 103 635
Depth armatures for pH measurements with ProfiLine pH 197 and ProfiLine pH 197-S pH depth armatures with built-in temperature sensors, cable (length optional) with waterproof plug (IP 67) 1.4571 steel armoring and screw-off protective hood, pressure-resistant to max. 10 bar, fits into 2” boreholes, without combination electrode Cable length
Order No.
Cable length
Order No.
TA 197 pH-4
4m
108 260
TA 197 pH-25
25 m
108 265
TA 197 pH-6
6m
108 261
TA 197 pH-40
40 m
108 266
TA 197 pH-10
10 m
108 262
TA 197 pH-60
60 m
108 267
TA 197 pH-15
15 m
108 263
TA 197 pH-100
100 m
108 268
TA 197 pH-20
20 m
108 264
Combination electrodes suitable for depth armature TA 197 pH pH combination electrode for heavily polluted waters
109 115
SensoLyt® GDA
pH combination electrode for surface waters and slightly polluted waters
109 116
SensoLyt® PtA
ORP combination electrode
109 125
Please refer to page 38 for electrodes and page 42 for further accessories.
Customer Service
SensoLyt® SEA
Photometry
Colony Counter
For other electrodes and buffer solutions see Accessories
Turbidity
pH combination electrode with built-in temperature sensor and waterproof plug, immersion depth 120 mm
Software, Printers
Portable pH meters
Respiration Sample Preparation
BOD
MultiParameter
Conductivity
Unidirectional RS 232 interface 2 analog recorder outputs for measurement and temperature output corresponding to display
Ordering Information
SenTix® 41
Laboratory & Field
Portable pH Meters
Wissenschaftlich-Technische Werkstätten GmbH & Co. KG · Dr.-Karl-Slevogt-Straße 1 · 82362 Weilheim · Germany · Tel.: +49 (0) 881-1 83-0 · Fax: +49 (0) 881-62 53 9
33
pH General Information about laboratory pH meters can be found on pages 20 - 25.
pH Meters Laboratory pH Meters inoLab® pH Level 1 inoLab® pH Level 2 inoLab® pH Level 3
inoLab® Level 1
Think innovative inoLab® pH Level 1: simple and reliable
Features Performance-oriented instrument range
Routine laboratory pH/mV meter with large multifunctional display for pH and temperature, automatic temperature compensation, MultiCal® calibration system; for battery or mains operation.
Simplified operator convenience
AutoRead automatic drift control for stable and reproducible measurements
Mains-independent Suitable as bench and wall-mounted models
inoLab® Level 2
Country-specific units ISO-conform documentation Application-oriented displays
See innovative inoLab® pH Level 2: compact and communicative Precision pH/mV meter with large multifunctional display for pH and temperature, automatic temperature compensation, MultiCal® calibration system, built-in measurement storage with GLP-conform documentation and digital interface. Option: with built-in printer (paper width 112 mm) and thermal paper accepted for use in official documents.
34
MultiCal® automatic calibration
IP 43
Feed and on/off keys keys for controlling the built-in printer
3 Year Warranty
Wissenschaftlich-Technische Werkstätten GmbH & Co. KG · Dr.-Karl-Slevogt-Straße 1 · 82362 Weilheim · Germany · Tel.: +49 (0) 881-1 83-0 · Fax: +49 (0) 881-62 53 9
General Features
Touch innovative
pH
inoLab® pH Level 3 with Terminal Level 3: flexible and powerful High-performance pH/mV/ion meter with graphics display and digital recorder function for pH, temperature and ion-selective measurement, automatic temperature compensation, high resolution (0.001 pH), MultiCal® calibration system, built-in measurement storage with GLP-conform documentation and digital interface. PC keyboard interface for connecting an external keyboard or a barcode reader. Includes software for direct control by PC. Option: with built-in printer (paper width 112 mm) and thermal paper accepted for use in official documents.
AutoRead automatic drift control for stable and reproducible measurements RUN/ENTER triggers the measuring process
IP 43
3 Year Warranty
Built-in digital plotter Connection for bar-code reader or PC keyboard Selectable instrument language Extended GLP functions Free-of-charge downloads for inoLab® pilot or terminal
Wissenschaftlich-Technische Werkstätten GmbH & Co. KG · Dr.-Karl-Slevogt-Straße 1 · 82362 Weilheim · Germany · Tel.: +49 (0) 881-1 83-0 · Fax: +49 (0) 881-62 53 9
Respiration Sample Preparation Colony Counter
Graphic evaluation possible
Photometry
Freely selectable buffer sets
Turbidity
5-point calibration by linear regression
Software, Printers
Features
Customer Service
Terminal Level3
BOD
MultiParameter
Conductivity
Oxygen (D.O.)
ISE
menu-guided graphics display
ORP
inoLab® Level 3
Laboratory & Field
Laboratory pH Meters
35
pH Technical Data Model
pH Level 1
Range/ Resolution
pH mV Temp.
Accuracy (±1 digit)
pH mV Temp.
pH Level 2
pH Level 3
±0.005 pH from -2 ...105 °C ±0.01 pH ±0.3 mV ±1 mV ±0.1 K
±0.003 pH from -2 ...105 °C ±0.01 pH ±0.2 mV
-2.000 ... +19.999 pH -2.00 ... +19.99 pH -999.9 ... +999.9 mV -1999 ... +1999 mV -5.0 ... +105.0 °C ±0.005 pH from -2 ...105 °C ±0.01 pH ±0.3 mV ±1 mV ±0.1 K
Temperature compensation pH
0... +99 °C automatically with TFK 150, TFK 325 or Pt-1000, or -20... +130 °C if sample temperature entered manually
AutoRead
For reproducibility better than 0.02 pH
Real-time clock
–
Calibration
MultiCal® automatic calibration AutoCal: automatic 2-/3-point calibration with DIN buffers
±0.1 K
yes
AutoCal-TEC: automatic 2-/3-point calibration with WTW technical buffers ConCal®: conventional 1-/2-point calibration with any buffers
MultiCal® automatic calibration AutoCal: automatic 2-/3-/5-point calibration with DIN buffers AutoCal-TEC: automatic 2-3-point calibration with WTW technical buffers ConCal®: conventional 1-/2-point calibration with any buffers ISECal: 2 and 3 point calibration with standard solutions
Calibration protocol
–
GLP-conform protocol of calibration; last calibration stored in memory
Calibration timer
–
adjustable, 1... 999 days
Sensor evaluation
Depends on the calibration results, shown in display
Limit values
–
Data memory
–
Data output
Display only
Display or interface
Display, interface or PC
Analog interface
–
Corresponds to electrode potential, i.e. 50... 62 mV/pH unit
Analog output corresponding to display in combination with terminal Level 3
Digital interface
–
Bidirectional RS 232
Bidirectional RS 232
Operating period/ Energy supply
3000 h with commercially available 4 x 1.5 V batteries or mains power supply
manual limit input with acoustic alarm 200 records (measurement, temperature) 2000 records (measurement, temperature)
Protection type
IEC 529 / IP 43 without built-in printer
Dimensions
230 x 210 x 70 mm (B x D x H)
250 x 300 x 70 mm (B x D x H)
Weight
1.3 kg
1.6 kg
Certified to
CE, TÜV/GS, UL, CUL
Warranty
3 years on the instrument
With terminal: universal plug-in power supply 230 VAC or 120 VAC Without terminal: via PC keyboard interface
36 Wissenschaftlich-Technische Werkstätten GmbH & Co. KG · Dr.-Karl-Slevogt-Straße 1 · 82362 Weilheim · Germany · Tel.: +49 (0) 881-1 83-0 · Fax: +49 (0) 881-62 53 9
Laboratory & Field General Features
Laboratory pH Meters
pH
Ordering Information for inoLab® pH meters inoLab® laboratory pH meters Compact precision pH meter with serial interface
1A20-110
inoLab® pH Level 2
Compact precision pH meter, additionally equipped with built- in printer for GLP-conform documentation
1A21-110
inoLab® pH Level 3
Flexible and powerful – the intelligent pH measuring place consisting of multifunction box and universal terminal, with PC software/connection cable
1A30-110
inoLab® pH Level 3
The intelligent pH measuring place, additionally equipped with built-in printer
1A31-110
inoLab® pH Level 3
The integrated pH measuring place, with PC software/connection cable, without printer/terminal
1A32-100
ISE
1A10-110
inoLab® pH Level 2
Ordering Information for inoLab® pH meters SETs – “ready to go” inoLab® pH SETs
1A10-111
inoLab® pH Level 2
Including electrode, passive multifunction box and accessories
1A20-111
inoLab® pH Level 2
Including built-in printer, electrode, passive multifunction box and accessories
1A21-111
inoLab® pH Level 3
Including terminal, electrode and accessories
1A30-111
inoLab® pH Level 3
With built-in printer, including terminal, electrode and accessories
1A31-111
inoLab® pH Level 3
Without printer/terminal, with PC software/connection cable, electrode and accessories
1A32-101
BOD
Including electrode, passive multifunction box and accessories
MultiParameter
Order No.
inoLab® pH Level 1
Conductivity
Oxygen (D.O.)
Simple and reliable pH meter for routine work
ORP
Order No.
inoLab® pH Level 1
21 41 61 81 HW
1
pH combination electrode, gel electrolyte pH combination electrode with built-in temperature sensor, gel electrolyte pH combination electrode, liquid electrolyte pH combination electrode with built-in temperature sensor, liquid electrolyte Precision electrode with ground diaphragm
SET ordering example inoLab® pH Level 1 + SenTix® 61 electrodes
2 3 4 H
1A10-111
3
Note: other electrodes in SET, instrument versions for 120 VAC/60 Hz or BNC versions are available on request
Customer Service
Software, Printers
Turbidity
Photometry
Please refer to page 38 for electrodes and page 42 for further accessories.
Colony Counter
SenTix® SenTix® SenTix® SenTix® SenTix®
Respiration Sample Preparation
SenTix® electrodes – please select one
Wissenschaftlich-Technische Werkstätten GmbH & Co. KG · Dr.-Karl-Slevogt-Straße 1 · 82362 Weilheim · Germany · Tel.: +49 (0) 881-1 83-0 · Fax: +49 (0) 881-62 53 9
37
pH ®
SenTix The clever idea for filling SenTix® electrodes Anyone who has to frequently work with pH electrodes knows about the awkward properties of KCl solution: • it climbs up beaker walls, • it penetrates even the finest pores and cracks and • it crystallizes out leaving an unpleasantlooking residue.
Topping up the electrolyte solution of combination electrodes and reference electrodes seldom happens without some drops escaping and forming harmless but nasty-looking crystalline stains in a very short time. This is why this should always be carried out on a working surface. This can even happen with the new range of SenTix® electrodes, but far less often when it is carried out correctly. But how?
Take the enclosed plastic dropping bottle and: • remove the red cap • cut off tip – if still sealed – as near the end as possible so that the tip can be inserted in the refilling hole of the SenTix® electrode to seal it off • in order to prevent overpressure in the electrode squeeze the dropping bottle gently and then insert the tip into the refilling hole so that the dropped bottle is seated firmly in the refilling hole. • by releasing and squeezing the bottle several times in succession (pumping) the topping-up process can be carried out perfectly without any mess
®
SenTix electrodes
SenTix® – the new electrode system from WTW offers more comfort, quality and precision ● The low-impedance membrane glass ensures that stable measurements are rapidly achieved even at low sample temperatures ● The reference electrolyte with its low silver ion content together with the temperature-insensitive platinum diaphragm prevent interference by precipitated silver. ● SenTix® electrodes are robust and shockproof. A special membrane glass and the plastic shaft ensure mechanical stability. ● SenTix® with liquid electrolyte – the optimized outflow speed rinses the platinum diaphragm free and prevents contamination by precipitates or dirt even during changes in temperature; with new membrane glass for even quicker response. ● SenTix® H and HW ground diaphragm electrodes allow the electrolyte outflow speed at the diaphragm to be altered. ● The clever sliding closure prevents the electrolyte from escaping during storage. ● Waterproof DIN or BNC plugs, either plug head system or with fixed cables, can be selected.
High-quality pH electrodes with liquid electrolyte for demanding work: SenTix® 60, SenTix® 61, SenTix® 62 SenTix® 81, SenTix® 82
pH electrodes with gel electrolyte for routine measurements on-site or in the laboratory: SenTix® 20, SenTix® 21, SenTix® 21-3, SenTix® 22, SenTix® 41, SenTix® 41-3, SenTix® 42 Surface pH electrode SenTix® Sur Penetration pH electrode SenTix® Sp
pH micro electrode SenTix® Mic
38
Precision pH electrode SenTix® H and SenTix® HW Wissenschaftlich-Technische Werkstätten GmbH & Co. KG · Dr.-Karl-Slevogt-Straße 1 · 82362 Weilheim · Germany · Tel.: +49 (0) 881-1 83-0 · Fax: +49 (0) 881-62 53 9
Order No.
Connection Electrode cable Electrode plug
103 631 as SenTix® 20, but with: Fixed cable Length 1 m DIN plug
103 640 as SenTix® 60, but with: Fixed cable Length 1 m DIN plug
SenTix® 21-3
SenTix® 41-3
103 632 as SenTix® 20, but with: Fixed cable Length 3 m DIN plug
103 636 as SenTix® 41, but with: Fixed cable Length 3 m DIN plug banana plug
SenTix® 22
SenTix® 42
SenTix® 62
SenTix® 82
103 633 as SenTix® 20, but with: Fixed cable Length 1 m BNC plug
103 637 as SenTix® 41, but with: Fixed cable Length 1 m BNC plug
103 641 as SenTix® 60, but with: Fixed cable Length 1 m BNC plug
103 643 as SenTix® 81, but with: Fixed cable Length 1 m BNC plug
Technical Data Order No. Measuring range pH Operating range °C Reference electrolyt Internal buffer Membrane shape Membrane resistance Diaphragm Shaft material Shaft length Shaft diameter Connection Electrode cable Electrode plug Temperature sensor
Laboratory & Field General Features Oxygen (D.O.)
SenTix® 61
MultiParameter
SenTix® 21
DIN plug and banana plug built-in NTC (30 KΩ)
Conductivity
DIN plug and banana plug built-in NTC (30 KΩ)
pH
103 642 0 ...14 pH 0 ...100 °C KCl 3 mol/l, Ag+-free pH = 7.0 ±0.25 conical