! W E N
A Superior Tracking and Support System for Conveyor Curves
CHARACTERISTICS
The Dual Magnetic System Curves are used in conjunction with stainless steel or plastic chains. The chains are retained in the system by the magnetic field created by the magnets that are located within the curve material. The Dual Magnetic System chains and curves, compared to the older tab or bevel system, offer the user greater flexibility and improved efficiency as the design allows for easy removal of the chains from the curve - for cleaning and maintenance purposes. In this way, magnetic corner tracks contribute to TPM (Total Productive Maintenance) programs.
ADVANTAGES
Steel and Plastic chains can be used in the same curves which means simpler conveyor construction, reduced inventories and ultimately lower costs. Stainless Steel sideflexing magnetic retained chain has the same hinge width as the 815 series straight running chain and therefore uses the identical sprockets to the 815 series. Easier maintenance construction Magnetic retained chains do not incorporate the use of tab or bevel shoes, therefore, with a magnetic system, chains can be removed from the curve without dismantling the chain. As a result, maintenance and cleaning is easier which reduces downtime.
NEW MAGNETIC SYSTEM WITH METAL STRIP: “EXTRA” CURVES
System Plast has recently developed a new magnetic corner retention system for dry-running applications. The system, which is patent pending, sets new performance standards in magnet curve technology due to the inclusion of a unique metal strip mounted in the inside bearing face of the top section. This area is constantly under load due to the pressure/speed factor. Main advantages: • Extreme dissipation of heat significantly reduces wear. • Under test conditions, lowest noise decibel levels were recorded. • ”Extra” curves are strongly recommended with plastic chains only! 2
MATERIAL - The standard upper section of the Dual Magnetic System curve is produced from 1200 grade UHMW-PE (ultra high molecular weight polyethylene) with the molecular weight exceeding 7.3 million g/mol., which ensures optimum wear life.
The return track is available in standard regenerated 1000 grade UHMW-PE (ultra high molecular weight polyethylene) with the molecular weight exceeding 4 million g/mol. This ensures a cost saving advantage for the end-user, as the wear on the return track is normally less significant than the top section. Standard - The standard color of the upper section is waterblue, but it is also available in different colors subject to minimum order quantity. The return section is black regenerate material.
Nolu-S - This type of material is strongly rec-
ommended for steel and plastic chains with higher running speeds. The upper section is Nolu-S (light grey). The return section is black regenerate material.
Nolu-SR - This type of material is
recommended for abrasive applications. The upper section is Nolu-SR (dark gray). The return section is black regenerate material.
All Nolu-S - The material of
choice, strongly recommended for all types of chains (steel, plastic, and chain-belts). It significantly reduces coefficients of friction making it ideal for applications requiring reduced friction, noise reduction, and higher dry-running speeds. The upper and return sections are Nolu-S (light grey).
MAGNETIC PACKS
System Plast has developed special magnetic packs for the Dual Magnetic System curves. These unique magnet holders are located into slots machined in the upper section of the curve.
DESIGN AND FUNCTIONALITY
Dual Magnetic System curves have the magnets positioned on the outside of the center line radius of each track which results in a more effective counteracting through the curve. The positioning of the magnets in the Dual Magnetic System does not increase the chain load or friction, unlike other similar systems.
Magnet
3
Nolu-S Material
UHMV
Solid lubricant
The Best Solution for the Upper Section of the Magnetic Corner Track
Nolu-S is a blend of UHMW and other dry lubricants that maintain good wear characteristics while significantly reducing coefficients of friction. Its unique self-lubricating properties make it ideal for applications requiring reduced friction, noise reduction, and higher dry-running speeds.
Why use Nolu-S for the Upper Part of the Curve? • Nolu-S makes very high speeds possible, especially when running dry. • Nolu-S has an extremely low coefficient of friction. • Nolu-S reduces noise and squeaking. • Nolu-S reduces chain pull. • Nolu-S extends the life of the chain. • Nolu-S reduces energy consumption • Nolu-S is UHMW-PE 1000 with a solid lubricant, FDA approved.
00
0
PE
50
E
HD
-P W
M
UH
00
10
E
-P W
M
UH
SM
12
/N
M
n
GS
tro la
(AVERAGE)
0
E
00
50
E
UH
M
-P W
00
10
E
-P W
12
n tro la
M
UH
SM
/N
M GS
S
u-
l No
Ny
MAX SPEED
4
PE
MAX. RECOMMENDED SURFACE SPEED (DRY - ACETAL LF CHAIN)
00
50
E
HD
-P W
00
10
M
UH
Ny
COEFFICIENT OF FRICTION
P HD
0
S
u-
l No
E
-P W
M
UH
12
SM
/N
M
n
tro la
GS
S
u-
l No
Ny
RELATIVE WEARLIFE
0
E
P HD
00
50
E
UH
M
-P W
00
10
E
-P W
n tro la
M
UH
12
SM
/N
M GS
Ny
PV - LIMIT
S
u-
l No
Curve Configuration Call our Engineering Experts To order the products you have selected or to get expert advice in choosing the right ones for your application, call our Engineering Department at 866-765-8744. We will be pleased to quote on curves manufactured to your special requirements. This page can be used when a special design or extensive modifications are required. Company Name:_ __________________________________________________________________ Contact Name:________________________________ Position:____________________________ Address:__________________________________________________________________________ L MATERIA City:_________________________________ State:__________ Zip:_______________________ Phone:_ __________________________________
Fax:_ ________________________________
L/2
P
TH
TH
H
SEC.A-A
SEC.A-A
TL
ONE TRACK
MULTI TRACKS
A
R
25 mm .98 in. 10 mm .39 in.
RETURN GUIDE SHOE
L = TL = R = P = H = TH =
A
RADIUS
TL
INSERTS
The magnetic corner tracks can be supplied with M8 or M10 threaded brass inserts (drawing required).
L MATERIA
Basic Dimensions
g. An
35 mm 1.38 in.
10 mm .39 in.
M8
INSERTS
H
L
Width Total Width Radius (first line) Pitch Height (upper part) Total Height
L MATERIA
SPECIAL DIMENSIONS
On request, tracks with special dimensions can be produced.
INSERTS INSERTS
75 mm 2.95 in.
TECHNICAL SUPPORT
For further information, contact our Technical Support Department
Explanation of Curve Reference (Example ordering information)
KMD Dual Magnetic System Curve
.
14
.
90
Model Angle Segment Radius R = 610mm/24 in. (90°) Pitch P = 85mm/3.35 in. Basic Width L = 100mm/3.94 in. Total Width TL = 270mm/10.63 in. Total Height TH = 90mm/3.54 in. Chain K = 82.5mm/3.25 in.
.
03 . Number of Tracks (3 Tracks)
A
Infeed Length A • Without infeed B • IL = 100mm/3.94 in. C • IL = 125mm/4.92 in. D • IL = 50mm/1.99 in.
5
Selection Tables 45 mm 1.77 in.
45 mm 1.77 in.
42.1 mm 1.66 in.
42.1 mm 1.66 in. 13.5 mm .53 in.
STEEL CHAIN
Steel Chain For Chain Series
Radius R
13.5 mm .53 in. PLASTIC CHAIN
Plastic Chain Pitch P
Basic Width L
Total Width TL
Top Track Height H
Version Series K
Reference Number
Page Number
K14
KMD.14_A
8
K27
KMD.23_A
9
K61
KMD.31_A
10
For chains with Lg 82.5 mm - K325” and Lg 83.8 mm - K330 Plate Width - Hinge L. 42.1 mm
879M - K325 880M - K325 881MO - K325
24 in 610 mm
3.35 in 85 mm
3.94 in 100 mm
PxN° of (tracks-1)+L
1.06 in 27 mm
For chains with Lg 114.3 - K450” Plate Width - Hinge L. 42.1 mm
879M - K450 880M - K450 881M - K450
24 in 610 mm
4.61 in 117 mm
5.08 in 129 mm
PxN° of (tracks-1)+L
1.06 in 27 mm
For chains with Lg 190.5 - K750” Plate Width - Hinge L. 42.1 mm
881M - K750
24 in 610 mm
7.72 in 196 mm
8.43 in 214 mm
PxN° of (tracks-1)+L
1.06 in 27 mm
45 mm 1.77 in. 42.1 mm 1.66 in.
8.7 mm .34 in. 13.5 mm .53 in.
For Chain Series
Radius R
Pitch P
Basic Width L
Total Width TL
Top Track Height H
Version Series K
Reference Number
Page Number
For chain belts with Lg 83.8 mm - K330” Plate Width - Hinge L. 42.1 mm - Plate Height 8.7 mm
2250M-K330FT 2250M-K330FG 2260M-K330FT
24 in 610 mm
3.35 in 85 mm
3.94 in 100 mm
PxN° of (tracks-1)+L
1.06 in 27 mm
KB14
KMD.15_A
11
For chain belts with Lg 114.3 mm - K450” Plate Width - Hinge L. 42.1 mm - Plate Height 8.7 mm
2250M-K450FT 6
24 in 610 mm
4.61 in 117 mm
5.08 in 129 mm
PxN° of (tracks-1)+L
1.06 in 27 mm
KB27
KMD.56_A
12
45 mm 1.77 in. 42.1 mm 1.66 in.
12.7 mm .50 in. 13.5 mm .53 in.
For Chain Series
Radius R
Pitch P
Basic Width L
Total Width TL
Top Track Height H
Version Series K
Reference Number
Page Number
For chain belts with Lg 83.8 mm - K330” Plate Width - Hinge L.42.1 mm - Plate Height 12.7 mm
2251M-K330FT
24 in 610 mm
3.35 in 85 mm
3.94 in 100 mm
PxN° of (tracks-1)+L
1.06 in 27 mm
KC14
KMD.16_A
13
For chain belts with Lg 83.8 mm - K330” Plate Width - Hinge L.42.1 mm - Plate Height 12.7 mm
2251M-K450FT
24 in 610 mm
4.61 in 117 mm
5.08 in 129 mm
PxN° of (tracks-1)+L
1.06 in 27 mm
KC27
KMD.66_A
14
60 mm 2.36 in. 57 mm 2.24 in. 17 mm .67 in.
For Chain Series
Radius R
Pitch P
Basic Width L
Total Width TL
Top Track Height H
Version Series K
Reference Number
Page Number
LBP86C
KMD.71_AC
15
LBP93C
KMD.78_AC
15
LBP94C
KMD.79_AC
15
LBP97C
KMD.82_AC
15
LBP98C
KMD.83_AC
15
For LBP chains with Lg 190.5 mm - K750” Plate Width - Hinge L. 57 mm
LBP882M-K750
33.85 in 860 mm
7.87 in 200 mm
8.43 in 214 mm
PxN° of (tracks-1)+L
1.26 in 32 mm
For LBP chains with Lg 254 mm - K1000” Plate Width - Hinge L. 57 mm
33.85 in 860 mm LBP882M-K1000
39.37 in 1000mm
10.63 in 270 mm
PxN° of (tracks-1)+L
1.26 in 32 mm
For LBP chains with Lg 304.8 mm - K1200” Plate Width - Hinge L. 57 mm
33.85 in 860 mm LBP882M-K1200
39.37 in 1000mm
12.60 in 320 mm
-
1.26 in 32 mm
7
L MATERIA
L MATERIA
Magnetic Corner Tracks for Chain Series: K325, K330
Tracks are available in four combinations of material. See page 3 for more information
The chains are retained in the system by a magnetic field created by magnets that are located within the track material. This design offers the user greater flexibility and improved efficiency by allowing easy removal of the chains from the curve for cleaning and maintenance purposes.
Tracks can be supplied with M8 or M10 threaded brass inserts (drawing required).
54 mm 2.13 in.
TL
31 mm 1.22 in.
8 mm .32 in.
23 mm .91 in.
28 mm 1.10 in.
54 mm 2.13 in.
27mm* 1.06in. 55 mm 2.17 in.
6 mm .24 in.
40 mm 1.58 in.
90 mm 3.54 in.
27mm* 1.06in. 6 mm .24 in.
63 mm* 2.48 in.
13.5 mm .53 in.
44 mm 1.73 in.
13.5 mm .53 in.
85 mm 3.35 in.
6 mm .24 in.
8 mm .32 in.
100 mm 3.94 in. 44 mm 1.73 in.
Pitch
50 mm 1.97 in.
48 mm 1.89 in.
INSERTS
INSERTS
Radius: 610 mm, 24 inches
Compatible with the following plastic chains: LF 880 M K325 / 11377M LF 879 M K325 / 11395M XPG 880 M K325 / 11500MG XPG 879 M K325 / 11397MG NG 880 M K325 / 11195M NG 879 M K325 / 11198M
54 mm 2.13 in.
28 mm 1.10 in.
18mm .71 in.
82 mm 3.23 in.
K14
Compatible with the following steel chains: SSL 881 MO K325 / 10208L SSEL 881 MO K325 / 10206L SSEL 881 MO K325 HB / 10213L SPSL 881 MO K325 / 10255L SPSL 881 MO K325 HB / 10265L
SEC. A-A
ONE TRACK
MULTI TRACKS *Tolerance on 27mm and 63mm is ±0.35mm or 0.015".
A in.
610 m 24 m
10 mm .39 in.
R1=
R1=
RETURN GUIDE SHOE
RADIUS
TL
teracting through the curve.
All Nolu-S
Add SR to part no. (KMD.14.90.01.ASR)
Add NS to part no. (KMD.14.90.01.ANS)
Part no. in table
Design Feature
The magnets are positioned on the outside of the center line radius of each track, which results in more effective coun-
Nolu-SR
Nolu-S
Standard
8
m
m 85 in. R1+ 3.35
R2=
°
10 mm .39 in.
25 mm .98 in.
35 mm 1.38 in.
90
M8
75 mm 2.95 in.
Number of Tracks
A
Add 2NS to part no. (KMD.14.90.01.A2NS)
Total Width TL 15°
30°
45°
60°
75°
90°
mm
inches
1
100
3.94
KMD.14.15.01.A
KMD.14.30.01.A
KMD.14.45.01.A
KMD.14.60.01.A
KMD.14.75.01.A
KMD.14.90.01.A
2
185
7.28
KMD.14.15.02.A
KMD.14.30.02.A
KMD.14.45.02.A
KMD.14.60.02.A
KMD.14.75.02.A
KMD.14.90.02.A
3
270
10.63
KMD.14.15.03.A
KMD.14.30.03.A
KMD.14.45.03.A
KMD.14.60.03.A
KMD.14.75.03.A
KMD.14.90.03.A
4
355
13.98
KMD.14.15.04.A
KMD.14.30.04.A
KMD.14.45.04.A
KMD.14.60.04.A
KMD.14.75.04.A
KMD.14.90.04.A
5
440
17.32
KMD.14.15.05.A
KMD.14.30.05.A
KMD.14.45.05.A
KMD.14.60.05.A
KMD.14.75.05.A
KMD.14.90.05.A
6
525
20.67
KMD.14.15.06.A
KMD.14.30.06.A
KMD.14.45.06.A
KMD.14.60.06.A
KMD.14.75.06.A
KMD.14.90.06.A
7
610
24.02
KMD.14.15.07.A
KMD.14.30.07.A
KMD.14.45.07.A
KMD.14.60.07.A
KMD.14.75.07.A
KMD.14.90.07.A
8
695
27.36
KMD.14.15.08.A
KMD.14.30.08.A
KMD.14.45.08.A
KMD.14.60.08.A
KMD.14.75.08.A
KMD.14.90.08.A
K27
L MATERIA
L MATERIA
Magnetic Corner Tracks for Chain Series: K450
Tracks are available in four combinations of material. See page 3 for more information
44 mm 1.73 in.
63mm* 27mm* 2.48in. 90mm 1.06in. 3.54in. 48 mm 1.89 in. 13.5 mm .53 in.
13.5 mm .53 in.
129 mm 5.08 in. 44 mm 1.73 in.
Pitch
117 mm 4.61 in.
6 mm .24 in.
6 mm .24 in. 23 mm .91 in.
54 mm 2.13 in.
63 mm 2.48 in.
TL
54 mm 2.13 in.
8 mm .32 in.
8 mm .32 in.
48 mm 1.89 in.
Tracks can be supplied with M8 or M10 threaded brass inserts (drawing required).
6 mm .24 in.
42.5 mm 1.67 in.
INSERTS
INSERTS
Radius: 610 mm, 24 inches
Compatible with the following plastic chains: LF 880 M K450 / 11380M LF 879 M K450 / 11396M XPG 880 M K450 / 11501MG XPG 879 M K450 / 11398MG NG 880 M K450 / 11197M NG 879 M K450 / 11421M
63mm* 27mm* 2.48in. 90mm 1.06in. 3.54in.
The chains are retained in the system by a magnetic field created by magnets that are located within the track material. This design offers the user greater flexibility and improved efficiency by allowing easy removal of the chains from the curve for cleaning and maintenance purposes.
64.5 mm 2.54 in.
Compatible with the following steel chains: SSE 881 M K450 / 10201
MULTI TRACKS
42.5 mm 1.67 in.
54 mm 2.13 in.
32.5 mm 1.28 in.
SEC. A-A
ONE TRACK
*Tolerance on 27mm and 63mm is ±0.35mm or 0.015".
A in.
610 m 24 m
10 mm .39 in.
10 mm .39 in.
75 mm 2.95 in.
RETURN GUIDE SHOE
RADIUS
Nolu-S
Standard
Design Feature
The magnets are positioned on the outside of the center line radius of each track, which results in more effective coun-
TL
teracting through the curve.
Nolu-SR
Add NS to part no. (KMD.14.90.01.ANS)
Part no. in table Number of Tracks
m
m . 117 R1+ 4.61 in
R2=
°
M8
90
25 mm .98 in.
35 mm 1.38 in.
R1=
A
All Nolu-S
Add SR to part no. (KMD.14.90.01.ASR)
Add 2NS to part no. (KMD.14.90.01.A2NS)
Total Width TL 15°
30°
45°
60°
75°
90°
mm
inches
1
129
5.08
KMD.23.15.01.A
KMD.23.30.01.A
KMD.23.45.01.A
KMD.23.60.01.A
KMD.23.75.01.A
KMD.23.90.01.A
2
246
9.69
KMD.23.15.02.A
KMD.23.30.02.A
KMD.23.45.02.A
KMD.23.60.02.A
KMD.23.75.02.A
KMD.23.90.02.A
3
363
14.29
KMD.23.15.03.A
KMD.23.30.03.A
KMD.23.45.03.A
KMD.23.60.03.A
KMD.23.75.03.A
KMD.23.90.03.A
4
480
18.90
KMD.23.15.04.A
KMD.23.30.04.A
KMD.23.45.04.A
KMD.23.60.04.A
KMD.23.75.04.A
KMD.23.90.04.A
5
597
23.50
KMD.23.15.05.A
KMD.23.30.05.A
KMD.23.45.05.A
KMD.23.60.05.A
KMD.23.75.05.A
KMD.23.90.05.A
6
714
28.11
KMD.23.15.06.A
KMD.23.30.06.A
KMD.23.45.06.A
KMD.23.60.06.A
KMD.23.75.06.A
KMD.23.90.06.A
7
831
32.72
KMD.23.15.07.A
KMD.23.30.07.A
KMD.23.45.07.A
KMD.23.60.07.A
KMD.23.75.07.A
KMD.23.90.07.A
8
948
37.32
KMD.23.15.08.A
KMD.23.30.08.A
KMD.23.45.08.A
KMD.23.60.08.A
KMD.23.75.08.A
KMD.23.90.08.A
9
K61
L MATERIA
L MATERIA
Magnetic Corner Tracks for Chain Series: K750
Tracks are available in four combinations of material. See page 3 for more information
The chains are retained in the system by a magnetic field created by magnets that are located within the track material. This design offers the user greater flexibility and improved efficiency by allowing easy removal of the chains from the curve for cleaning and maintenance purposes.
INSERTS
Radius: 610 mm, 24 inches
27mm* 63 mm* 2.48 in. 90 mm 1.06in. 3.54 in.
13.5 mm .53 in.
44 mm 1.73 in.
6 mm .24 in.
48 mm 1.89 in.
Compatible with the following plastic chains: LF 880 M K750 / 11393M XPG 880 M K750 / 11394MG NG 880 M K750 / 11420M
INSERTS
Tracks can be supplied with M8 or M10 threaded brass inserts (drawing required).
214 mm 8.43 in.
25 mm .98 in.
8 mm .32 in.
Compatible with the following steel chains: SSE 881 M K750 / 10203
60 mm 2.36 in.
104 mm 4.09 in.
ONE TRACK
25 mm SEC. A-A .98 in.
*Tolerance on 27mm and 63mm is ±0.35mm or 0.015". Pitch
196 mm 7.72 in.
44 mm 1.73 in.
6 mm .24 in.
63 mm* 27mm* 2.48 in. 90 mm 1.06in. 3.54 in.
48 mm 1.89 in.
13.5 mm .53 in.
107 mm 4.21 in.
6 mm .24 in. 23 mm .91 in.
25 mm .98 in.
8 mm .32 in.
60 mm 2.36 in.
104 mm 4.09 in.
TL
32 mm 1.26 in.
60 mm 2.36 in.
MULTI TRACKS
104 mm 4.09 in.
A in.
610 m 24 m
10 mm .39 in.
R1= 10 mm .39 in.
25 mm .98 in.
35 mm 1.38 in.
° 90
M8
RETURN GUIDE SHOE
TL
Nolu-SR
Nolu-S
Standard
10
Design Feature
The magnets are positioned on the outside of the center line radius of each track, which results in more effective counteracting through the curve.
All Nolu-S
Add SR to part no. (KMD.14.90.01.ASR)
Add NS to part no. (KMD.14.90.01.ANS)
Part no. in table
1
m
m . 196 R1+ 7.72 in
R2=
RADIUS
75 mm 2.95 in.
Number of Tracks
A
Add 2NS to part no. (KMD.14.90.01.A2NS)
Total Width TL mm
inches
214
8.43
15°
KMD.31.15.01.A
30°
KMD.31.30.01.A
45°
KMD.31.45.01.A
60°
KMD.31.60.01.A
75°
KMD.31.75.01.A
90°
KMD.31.90.01.A
2
410
16.14
KMD.31.15.02.A
KMD.31.30.02.A
KMD.31.45.02.A
KMD.31.60.02.A
KMD.31.75.02.A
KMD.31.90.02.A
3
606
23.86
KMD.31.15.03.A
KMD.31.30.03.A
KMD.31.45.03.A
KMD.31.60.03.A
KMD.31.75.03.A
KMD.31.90.03.A
KB14
L MATERIA
Magnetic Corner Tracks for Chain Series: K330
Tracks are available in four combinations of material. See page 3 for more information
The chains are retained in the system by a magnetic field created by magnets that are located within the track material. This design offers the user greater flexibility and improved efficiency by allowing easy removal of the chains from the curve for cleaning and maintenance purposes.
Tracks can be supplied with M8 or M10 threaded brass inserts (drawing required).
54 mm 2.13 in.
54 mm 2.13 in.
28mm 1.10in.
18mm .71in.
82 mm 3.23 in.
27mm* 1.06in. 55 mm 2.17 in.
45 mm 1.77 in.
11 mm .43 in.
6 mm .24 in.
6 mm .24 in.
31 mm 1.22 in. TL
90 mm 3.54 in.
27mm* 1.06in. 24 mm .95 in.
63 mm* 2.48 in.
11 mm .43 in.
54 mm 2.13 in.
13.5 mm .53 in.
85 mm 3.35 in.
11 mm .43 in.
28 mm 1.10 in.
100 mm 3.94 in. 44 mm 1.73 in.
Pitch
50 mm 1.97 in. 44 mm 1.73 in.
13.5 mm .53 in.
INSERTS
INSERTS
Radius: 610 mm, 24 inches
53 mm 2.09 in.
Compatible with the following side flexing chain belts: LFG 2250 M K330 FT / 11320 XPG 2250 M K330 FT / 11320XPG LFG 2260 M K330 FT / 11329 XPG 2260 M K330 FT / 11329XPG
L MATERIA
SEC. A-A
ONE TRACK
MULTI TRACKS *Tolerance on 27mm and 63mm is ±0.35mm or 0.015".
A
25 mm .98 in. 10 mm .39 in.
m 85m . R1+ .35 in 3
R2=
Design Feature
The magnets are positioned on the outside of the center line radius of each track, which results in more effective coun-
RADIUS
TL
teracting through the curve.
Nolu-S
Standard
Nolu-SR
Add NS to part no. (KMD.14.90.01.ANS)
Part no. in table Number of Tracks
A
°
M8
75 mm 2.95 in.
RETURN GUIDE SHOE
90
35 mm 1.38 in.
R1=
in.
610 m 24 m
10 mm .39 in.
All Nolu-S
Add SR to part no. (KMD.14.90.01.ASR)
Add 2NS to part no. (KMD.14.90.01.A2NS)
Total Width TL 15°
30°
45°
60°
75°
90°
mm
inches
1
100
3.94
KMD.15.15.01.A
KMD.15.30.01.A
KMD.15.45.01.A
KMD.15.60.01.A
KMD.15.75.01.A
KMD.15.90.01.A
2
185
7.28
KMD.15.15.02.A
KMD.15.30.02.A
KMD.15.45.02.A
KMD.15.60.02.A
KMD.15.75.02.A
KMD.15.90.02.A
3
270
10.63
KMD.15.15.03.A
KMD.15.30.03.A
KMD.15.45.03.A
KMD.15.60.03.A
KMD.15.75.03.A
KMD.15.90.03.A
4
355
13.98
KMD.15.15.04.A
KMD.15.30.04.A
KMD.15.45.04.A
KMD.15.60.04.A
KMD.15.75.04.A
KMD.15.90.04.A
5
440
17.32
KMD.15.15.05.A
KMD.15.30.05.A
KMD.15.45.05.A
KMD.15.60.05.A
KMD.15.75.05.A
KMD.15.90.05.A
6
525
20.67
KMD.15.15.06.A
KMD.15.30.06.A
KMD.15.45.06.A
KMD.15.60.06.A
KMD.15.75.06.A
KMD.15.90.06.A
7
610
24.02
KMD.15.15.07.A
KMD.15.30.07.A
KMD.15.45.07.A
KMD.15.60.07.A
KMD.15.75.07.A
KMD.15.90.07.A
8
695
27.36
KMD.15.15.08.A
KMD.15.30.08.A
KMD.15.45.08.A
KMD.15.60.08.A
KMD.15.75.08.A
KMD.15.90.08.A
11
KB27
Magnetic Corner Tracks for Chain Series: K450
63 mm 2.48 in.
90mm 3.54in. 63mm* 2.48in.
53 mm 2.09 in.
63mm* 2.48in.
54 mm 2.13 in.
11 mm .43 in.
TL
54 mm 2.13 in.
42.5 mm 1.67 in.
6 mm .24 in.
54 mm 2.13 in.
27mm* 1.06in.
13.5 mm .53 in.
27mm* 1.06in.
44 mm 1.73 in.
11 mm .43 in. 24 mm .95 in.
6 mm .24 in.
129 mm 5.08 in. 44 mm 1.73 in.
Pitch
117 mm 4.61 in.
90mm 3.54in.
13.5 mm .53 in.
Tracks can be supplied with M8 or M10 threaded brass inserts (drawing required).
11 mm .43 in.
42.5 mm 1.67 in.
INSERTS
INSERTS
Radius: 610 mm, 24 inches
64.5 mm 2.54 in.
Compatible with the following side flexing chain belts: LFG 2250 M K450 FT / 11327 XPG 2250 M K450 FT / 11327XPG
Tracks are available in four combinations of material. See page 3 for more information
The chains are retained in the system by a magnetic field created by magnets that are located within the track material. This design offers the user greater flexibility and improved efficiency by allowing easy removal of the chains from the curve for cleaning and maintenance purposes.
53 mm 2.09 in.
L MATERIA
L MATERIA
ONE TRACK
MULTI TRACKS
32.5 mm 1.28 in.
SEC. A-A
*Tolerance on 27mm and 63mm is ±0.35mm or 0.015".
A
25 mm .98 in.
RETURN
M8 GUIDE SHOE
75 mm 2.95 in.
A
m 17m 1+1 .61 in. 4
R R2=
°
10 mm .39 in.
90
35 mm 1.38 in.
R1=
in.
610 m 24 m
10 mm .39 in.
Design Feature
TL
RADIUS
The magnets are positioned on the outside of the center line radius of each track, which results in more effective counteracting through the curve.
Nolu-S
Standard
Part no. in table Number of Tracks
12
Nolu-SR
Add NS to part no. (KMD.14.90.01.ANS)
All Nolu-S
Add SR to part no. (KMD.14.90.01.ASR)
Add 2NS to part no. (KMD.14.90.01.A2NS)
Total Width TL 15°
30°
45°
60°
75°
90°
mm
inches
1
129
5.08
KMD.56.15.01.A
KMD.56.30.01.A
KMD.56.45.01.A
KMD.56.60.01.A
KMD.56.75.01.A
KMD.56.90.01.A
2
246
9.69
KMD.56.15.02.A
KMD.56.30.02.A
KMD.56.45.02.A
KMD.56.60.02.A
KMD.56.75.02.A
KMD.56.90.02.A
3
363
14.29
KMD.56.15.03.A
KMD.56.30.03.A
KMD.56.45.03.A
KMD.56.60.03.A
KMD.56.75.03.A
KMD.56.90.03.A
4
480
18.90
KMD.56.15.04.A
KMD.56.30.04.A
KMD.56.45.04.A
KMD.56.60.04.A
KMD.56.75.04.A
KMD.56.90.04.A
KC14
Magnetic Corner Tracks for Chain Series: K330
INSERTS
INSERTS
Radius: 610 mm, 24 inches
Tracks can be supplied with M8 or M10 threaded brass inserts (drawing required).
54 mm 2.13 in.
28 mm 1.10 in.
31 mm 1.22 in. TL
54 mm 2.13 in.
54 mm 2.13 in.
28mm 1.10in.
18mm .71in.
82 mm 3.23 in.
55 mm* 2.17 in.
13.5 mm .53 in. 5 mm .20 in.
25 mm .98 in.
15 mm .59 in.
40 mm 1.58 in.
15 mm .59 in.
90 mm 3.54 in.
27mm* 1.06in.
15 mm .59 in.
63 mm* 2.48 in.
13.5 mm .53 in.
44 mm 1.73 in.
85 mm 3.35 in.
27mm* 1.06in.
100 mm 3.94 in. 44 mm 1.73 in.
Pitch
50 mm 1.97 in.
5 mm .20 in.
Compatible with the following side flexing chain belts: LFG 2251 M K330 FT / 11322 XPG 2251 M K330 FT / 11322XPG
Tracks are available in four combinations of material. See page 3 for more information
The chains are retained in the system by a magnetic field created by magnets that are located within the track material. This design offers the user greater flexibility and improved efficiency by allowing easy removal of the chains from the curve for cleaning and maintenance purposes.
55 mm 2.17 in.
L MATERIA
L MATERIA
SEC. A-A
ONE TRACK
MULTI TRACKS *Tolerance on 27mm and 63mm is ±0.35mm or 0.015".
A
RETURN M8 GUIDE SHOE
m 85m . R1+ .35 in 3
Design Feature
R2=
RADIUS
75 mm 2.95 in.
TL
The magnets are positioned on the outside of the center line radius of each track, which results in more effective counteracting through the curve.
Nolu-S
Standard
Nolu-SR
Add NS to part no. (KMD.14.90.01.ANS)
Part no. in table Number of Tracks
A
°
10 mm .39 in.
90
25 mm .98 in.
35 mm 1.38 in.
R1=
in.
610 m 24 m
10 mm .39 in.
All Nolu-S
Add SR to part no. (KMD.14.90.01.ASR)
Add 2NS to part no. (KMD.14.90.01.A2NS)
Total Width TL 15°
30°
45°
60°
75°
90°
mm
inches
1
100
3.94
KMD.16.15.01.A
KMD.16.30.01.A
KMD.16.45.01.A
KMD.16.60.01.A
KMD.16.75.01.A
KMD.16.90.01.A
2
185
7.28
KMD.16.15.02.A
KMD.16.30.02.A
KMD.16.45.02.A
KMD.16.60.02.A
KMD.16.75.02.A
KMD.16.90.02.A
3
270
10.63
KMD.16.15.03.A
KMD.16.30.03.A
KMD.16.45.03.A
KMD.16.60.03.A
KMD.16.75.03.A
KMD.16.90.03.A
4
355
13.98
KMD.16.15.04.A
KMD.16.30.04.A
KMD.16.45.04.A
KMD.16.60.04.A
KMD.16.75.04.A
KMD.16.90.04.A
5
440
17.32
KMD.16.15.05.A
KMD.16.30.05.A
KMD.16.45.05.A
KMD.16.60.05.A
KMD.16.75.05.A
KMD.16.90.05.A
6
525
20.67
KMD.16.15.06.A
KMD.16.30.06.A
KMD.16.45.06.A
KMD.16.60.06.A
KMD.16.75.06.A
KMD.16.90.06.A
7
610
24.02
KMD.16.15.07.A
KMD.16.30.07.A
KMD.16.45.07.A
KMD.16.60.07.A
KMD.16.75.07.A
KMD.16.90.07.A
8
695
27.36
KMD.16.15.08.A
KMD.16.30.08.A
KMD.16.45.08.A
KMD.16.60.08.A
KMD.16.75.08.A
KMD.16.90.08.A
13
KC27
Magnetic Corner Tracks for Chain Series: K450
63 mm 2.48 in.
54 mm 2.13 in.
90 mm 3.54 in. 63 mm* 2.48 in.
15 mm .59 in.
42.5 mm 1.67 in.
5 mm .20 in.
54 mm 2.13 in.
55 mm 2.17 in.
63 mm* 2.48 in.
25 mm .98 in.
TL
27mm* 1.06in.
13.5 mm .53 in.
27mm* 1.06in.
44 mm 1.73 in.
15 mm .59 in.
5 mm .20 in.
129 mm 5.08 in. 44 mm 1.73 in.
Pitch
117 mm 4.61 in.
90 mm 3.54 in.
13.5 mm .53 in.
Tracks can be supplied with M8 or M10 threaded brass inserts (drawing required).
15 mm .59 in.
42.5 mm 1.67 in.
INSERTS
INSERTS
Radius: 610 mm, 24 inches
64.5 mm 2.54 in.
Compatible with the following side flexing chain belts: LFG 2251 M K450 FT / 11328 XPG 2251 M K450 FT / 11328XPG
Tracks are available in four combinations of material. See page 3 for more information
The chains are retained in the system by a magnetic field created by magnets that are located within the track material. This design offers the user greater flexibility and improved efficiency by allowing easy removal of the chains from the curve for cleaning and maintenance purposes.
55 mm 2.17 in.
L MATERIA
L MATERIA
54 mm 2.13 in.
SEC. A-A
ONE TRACK
MULTI TRACKS
32.5mm 1.28 in.
*Tolerance on 27mm and 63mm is ±0.35mm or 0.015".
A in.
610 m 24 m
10 mm .39 in.
25 mm .98 in. 10 mm .39 in.
M8
RETURN GUIDE SHOE
75 mm 2.95 in.
° 90
35 mm 1.38 in.
R1=
A m 85m . R1+ .35 in 3
R2=
RADIUS
Design Feature
TL
The magnets are positioned on the outside of the center line radius of each track, which results in more effective counteracting through the curve.
Nolu-S
Standard
Number of Tracks
14
Nolu-SR
Add NS to part no. (KMD.14.90.01.ANS)
Part no. in table
All Nolu-S
Add SR to part no. (KMD.14.90.01.ASR)
Add 2NS to part no. (KMD.14.90.01.A2NS)
Total Width TL 15°
30°
45°
60°
75°
90°
mm
inches
1
129
5.08
KMD.66.15.01.A
KMD.66.30.01.A
KMD.66.45.01.A
KMD.66.60.01.A
KMD.66.75.01.A
KMD.66.90.01.A
2
246
9.69
KMD.66.15.02.A
KMD.66.30.02.A
KMD.66.45.02.A
KMD.66.60.02.A
KMD.66.75.02.A
KMD.66.90.02.A
3
363
14.29
KMD.66.15.03.A
KMD.66.30.03.A
KMD.66.45.03.A
KMD.66.60.03.A
KMD.66.75.03.A
KMD.66.90.03.A
4
480
18.90
KMD.66.15.04.A
KMD.66.30.04.A
KMD.66.45.04.A
KMD.66.60.04.A
KMD.66.75.04.A
KMD.66.90.04.A
K750, K1000, K1200
Magnetic Corner Tracks for Chain Series: K750, K1000, K1200
Tracks are available in four combinations of material. See page 3 for more information
The chains are retained in the system by a magnetic field created by magnets that are located within the track material. This design offers the user greater flexibility and improved efficiency by allowing easy removal of the chains from the curve for cleaning and maintenance purposes.
Tracks can be supplied with M8 or M10 threaded brass inserts (drawing required).
32mm 1.26in. 95 mm 3.74 in.
17 mm .67 in.
2.14 mm 8.43 in. 60 mm 2.36 in.
63 mm 2.48 in.
22 mm .87 in.
8 mm .32 in.
78 mm 3.07 in.
101 mm 3.98 in.
ONE TRACK
SEC. A-A
35 mm 1.38 in. Pitch
107 mm 4.21 in.
95 mm 3.74 in.
32mm 1.26in.
17 mm .67 in.
60 mm 2.36 in.
200 mm 7.87 in.
8 mm .32 in.
63 mm 2.48 in.
22 mm .87 in.
78 mm 3.07 in.
100 mm 3.94 in.
58 mm 2.28 in.
42 mm 1.65 in.
101 mm 3.98 in.
35 mm 1.38 in.
TL
MULTI TRACKS
A
10 mm .39 in.
RETURN GUIDE SHOE
°
75 mm 2.95 in.
M8
A
90
10 mm .39 in.
25 mm .98 in.
35 mm 1.38 in.
.
R1= 860 33.8 mm 6 in
48 mm 1.89 in.
INSERTS
INSERTS
Radius: 860 mm, 34 inches
48 mm 1.89 in.
Compatible with the following side flexing chain belts: LBP 882 M K750 / 11073 LBP 882 M K1000 / 11074 LBP 882 M K1200 / 11075
L MATERIA
L MATERIA
200mm R2=R1+ .87 in. 7
RADIUS
TL
Design Feature
The magnets are positioned on the outside of the center line radius of each track, which results in more effective counteracting through the curve.
Magnetic corner tracks for these chains are available. Please see the complete System Plast Conveyor Chains catalog for details or contact our Engineering Department. 15
Side Flexing Magnetic Chains RD = 3.15
SC
Steel Chain
1.66
.12
Plastic Chain
.26
.39
.53 1.06
1.50
RD = 2.0
1.50
.28
1.06 .53
Ø.25
L
R.
R.
TRAVEL
TRAVEL
Material: "Standard" 430 grade ferritic stainless steel.
Chain Reference
Part Version Yield Surface Finish Flatness Polished L R Weight Number Series (K) Point (lbs.) (micro in.) (max) Hinges (width) Min. SC (lbs./ft.)
SSL 881 MO K325 10208L
K14
1215
24
.004
yes
3-1/4 20 177 1.68
Material: Special 400 series "Extra Plus" high performance stainless steel.
SSEL 881 MO K325 SSE 881 M K450 SSE 881 M K750 SPSL 881 MO K325
10206L 10201 10203 10255L
K14 K27 K61 K14
1912 1912 1912 1912
12 12 12 8
.004 .008 .012 .004
yes no no yes
3-1/4 4-1/2 7-1/2 3-1/4
20 20 20 20
1.77 1.77 1.77 177
1.68 2.08 3.29 1.68
Material: Special 400 series "Extra Plus" high performance stainless steel. Pins are made from vacuum hardened stainless steel.
SSEL 881 MO K325 HB 10213L SPSL 881 MO K325 HB 10265L
K14 K14
1912 1912
12 8
.004 .004
yes yes
3-1/4 20 1.77 1.68 3-1/4 20 1.77 1.68
Material: "LF Brown" Low friction acetal. Part Version Chain Reference Number Series (K)
LF 880 M K325 LF 880 M K450 LF 879 M K325 LF 879 M K450
SC 1.66 .53 1.06
K14 K27 K14 K27
L (width)
B (thickness)
R Min.
SC
Weight (lbs./ft.)
1283 1283 1283 1283
3-1/4 4-1/2 3-1/4 4-1/2
.16 .16 .19 .19
20 20 20 20
1.77 1.77 1.77 1.77
.71 .77 .77 .84
11500MG 11501MG 11397MG 11398MG
K14 K27 K14 K27
3-1/4 4-1/2 3-1/4 4-1/2
.16 .16 .19 .19
20 20 20 20
1.77 1.77 1.77 1.77
.71 .77 .77 .84
3-1/4 4-1/2 3-1/4 4-1/2
.16 .16 .19 .19
20 20 20 20
1.77 1.77 1.77 1.77
.71 .77 .77 .84
1239 1239 1239 1239
Material: "NG Green" Our proprietary lowest friction PBT.
11195M 11197M 11198M 11421M
K14 K27 K14 K27
1170 1170 1170 1170
SC 1.66
Chain Belts
RD = 5.51 .34
11377M 11380M 11395M 11396M
Breaking Load (lbs.)
Material: "XPG Dark Grey" Very low friction acetal.
XPG 880 M K325 XPG 880 M K450 XPG 879 M K325 XPG 879 M K450 NG 880 M K325 NG 880 M K450 NG 879 M K325 NG 879 M K450
Chain Belts
RD = 5.51 .50
.48 .84 1.0
.53 1.06
1.0
LFG 2250 M K330 FT 11320 LFG 2250 M K450 FT 11327 LFG 2260 M K330 FT 11329
KB14 KB27 KB14
L
R min.
SC Straight
SC Curved
3.3 4.5 3.3
20 20 20
1.77 1.77 1.77
1.73 1.73 1.73
3.3 4.5 3.3
Max Weight Load (lbs.) (lbs./ft.)
450 450 450
1.18 1.31 1.17
20 20 20
1.77 1.77 1.77
1.73 1.73 1.73
450 450 450
1.18 1.31 1.17
Chain Reference
Part Version Number Series (K)
LFG 2251 M K330 FT LFG 2251 M K450 FT
11322 11328
KC14 KC27
L (width)
R min.
SC Straight
SC Curved
3.3 4.5
20 20
1.81 1.81
1.77 1.77
450 450
1.28 1.28
Max Weight Load (lbs.) (lbs./ft.)
20 20
1.81 1.81
1.77 1.77
450 450
1.28 1.28
Material: "XPG Dark Brown" Very low friction acetal.
XPG 2251 M K330 FT 11322XPG KC14 XPG 2251 M K450 FT 11328XPG KC27
3.3 4.5
Customer Service Toll free
Ø.32
Material: "LFG Dark Grey" Low friction acetal.
L (width)
Material: “XPG Dark Grey” Very low friction acetal.
XPG 2250 M K330 FT 11320XPG KB14 XPG 2250 M K450 FT 11327XPG KB27 XPG 2260 M K330 FT 11329XPG KB14
1.0
R.
R.
Part Version Number Series (K)
1.0
.64
Ø.31
L
1.0
Material: "LFG Dark Grey" Low friction acetal. Chain Reference
1.50
.30
L
1.50
SC 1.66
B
phone:(866) 765-8744 fax:(866) 447-6587 S o l u s i i
4 4 S o l u s
30152 Aventura Rancho Santa Margarita, California 92688 phone: (949) 589-3900 fax: (949) 858-0300 Indianapolis, Indiana • Sanford, North Carolina • Tlajomulco de Zuñiga, Jalisco, Mexico
[email protected] www.solusii.com
© 2008 Solus Industrial Innovations, LLC 10/08