Mounting ETS-Lindgren Antennas
Before mounting an antenna, see Safety Information. For complete safety, regulatory, and This guide describes the hardware required to mount your ETS-Lindgren antenna to a tripod, mast, or boom,
other product marking information, see the user manual for your ETS-Lindgren antenna.
and is intended to be used in conjunction with the antenna user manual. This guide does not replace the antenna user manual. Safety Information WARRANTY
These antennas and mount destinations are included: ONLY QUALIFIED PERSONNEL should install, operate, or service this equipment. CONTACT ETS-LINDGREN PRIOR TO SERVICING. Servicing (or modifying) the unit by yourself may void your warranty. If you attempt to service the unit by yourself, disconnect all electrical power before starting. There are voltages at many points in the instrument that could, if contacted, cause personal injury. Only trained service personnel should perform adjustments and/or service procedures upon this instrument. Capacitors inside this instrument may still be CHARGED even when instrument is disconnected from its power source.
Antenna Type BiConiLog™ Antennas – 3140B, 3149, 3142C, 3142D, 3142E, 3143B Biconical Antennas – 3109, 3104C, 3110B, 3110C Mini-Bicon Antennas – 3180, 3180B, 3181, 3182, 3183, 3184 Log Periodic Antennas – 3144, 3147, 3148, 3148B, 3186
Warranty Information
Double-Ridged Waveguide Horns – 3106B, 3115, 3116, 3116B, 3116C, 3117, 3119
For complete warranty information, see the user manual for your ETS-Lindgren antenna.
3164 Series Horns – Quad-Ridged Horns (–05, –06, –07, –08, –10, –11) – Dual-Polarized Horns (–03, –04) Pyramidal Horn Antennas – 3160 Series, 3161 Series Dipoles – 3121C, 3121D Loop Antennas and Rod Antennas – loop antennas, rod antennas Conical Log Spirals – 3101, 3102, 3103 High Gain Conical Horns – 3163 Series (–03, –04, –05, –06) Mount Destination Model 4-TR Tripod – ETS-Lindgren 4-TR tripod Model 7-TR Tripod Positioner – includes 109042, 108983, 118947, and 108507 booms: 109042 – straight; for general antenna mounting on a 7-TR 108983 – offset; for general antenna mounting on a 7-TR with pneumatic or manual polarization;
USA Headquarters 1301 Arrow Point Drive Cedar Park, TX 78613 Phone: +1.512.531.6400
[email protected]
118947 – for stinger-type antennas only
Please see www.ets-lindgren.com for a list of all ETS-Lindgren offices.
108507 – for the 3106 and 3106B only
can also be used to mount stinger-type antennas
© Copyright 2008–2013 by ETS-Lindgren Inc. All Rights Reserved. No part of this document may be copied by any means without written permission from ETS-Lindgren Inc.
Mast – 2070 Series, 2075, and 2175 Antenna Towers 2x2 Boom – typical 2-inch by 2-inch boom; non-ETS-Lindgren and previous generation EMCO positioning systems
The ETS-Lindgren logo and BiConiLog are trademarks of ETS-Lindgren Inc.
399807, Rev G
Revision/Date: A, Initial Release–June, 2008 B, Updates–February, 2009
C, Added mini-bicons, 3301C–November, 2009 D, Updated 3149 mounting, added 3163–March, 2010
E, Added 3116B, 3119, 3164-10–November, 2010 F, Added 3106B mounting info–July, 2013
G, Added 118947, 3116C, 3142E, 3143B, 3164-11, 3180B, 3186–November, 2013
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
BiConiLog™ Antennas 3140B
7-TR, Mast
4-TR 100989 Polarizing Antenna Adapter (2) OR 106470 Non-Polarizing Antenna Adapter (2)
Do not mount to a 4-TR.
To antenna mounting bracket, insert knob
OR
2x2 Boom
100989 Polarizing Antenna Adapter (2) OR 106470 Non-Polarizing Antenna Adapter (2)
100989 Polarizing Antenna Adapter OR 106470 Non-Polarizing Antenna Adapter
To antenna mounting bracket, insert knob
To antenna mounting bracket, insert knob 105861 Thread Insert
105861 Thread Insert (2) 104136 Boom Antenna Mount Knob (2)
Through boom on 7-TR, Mast
104169 Boom Antenna Mount Knob (2) Through boom on 7-TR, Mast
101913 Fixed Antenna Mount
Stinger Mounts 4-TR – Do not mount to a 4-TR
Notes 7-TR refers to 109042, 108983, and 118947 booms:
7-TR – Mounts directly to a 7-TR without additional hardware
109042 – straight; for general antenna mounting on a 7-TR
Mast – Additional hardware required to mount to a mast
108983 – offset; for general antenna mounting on a 7-TR with pneumatic or manual polarization; can also be used to mount stinger-type antennas
Standard Parts Antennas shown here ship with these standard parts: 105861 Thread Insert (3140B ships with two) 100989 Polarizing Antenna Adapter (3140B ships with two)
Insert boom through Antennas include mounting bracket (attached) and mounting knob(s)
118947 – for stinger-type antennas only Mast refers to 2070 Series, 2075, and 2175 Antenna Towers 2x2 Boom refers to a typical 2-inch by 2-inch boom; non-ETS-Lindgren and previous generation EMCO positioning systems
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
BiConiLog™ Antennas, continued 3149, 3142D/C/E, 3143B 3149
Stinger Mounts
4-TR 100989 Polarizing Antenna Adapter
OR
101950 Support Rod To antenna mounting bracket, insert knob
To antenna mounting bracket, insert knob
3142E
OR
To antenna mounting bracket, insert knob
105861 Thread Insert
105861 Thread Insert
101942B Support Base
To 4-TR
4-TR – Do not mount to a 4-TR
100989 Polarizing Antenna Adapter OR 106470 Non-Polarizing Antenna Adapter
109042 – straight; for general antenna mounting on a 7-TR
Mast – Additional hardware required to mount to a mast
108983 – offset; for general antenna mounting on a 7-TR with pneumatic or manual polarization; can also be used to mount stinger-type antennas
Antennas shown here ship with these standard parts:
To 4-TR
105861 Thread Insert (3140B ships with two) 100989 Polarizing Antenna Adapter (3140B ships with two) Antennas include mounting bracket (attached) and mounting knob(s)
To 4-TR
7-TR refers to 109042, 108983, and 118947 booms:
7-TR – Mounts directly to a 7-TR without additional hardware
Standard Parts
102308 Swivel Antenna Mount
Notes
118947 – for stinger-type antennas only Mast refers to 2070 Series, 2075, and 2175 Antenna Towers 2x2 Boom refers to a typical 2-inch by 2-inch boom; non-ETS-Lindgren and previous generation EMCO positioning systems
The 3149 can mount directly to a 4-TR. Use of a 102308 Swivel Antenna Mount simplifies polarization, and is optional.
3142D 7-TR, Mast 100989 Polarizing Antenna Adapter OR 106470 Non-Polarizing Antenna Adapter
OR
2x2 Boom 100989 Polarizing Antenna Adapter OR 106470 Non-Polarizing Antenna Adapter
100989 Polarizing Antenna Adapter OR 106470 Non-Polarizing Antenna Adapter
To antenna mounting bracket, insert knob
To antenna mounting bracket, insert knob
3142C To antenna mounting bracket, insert knob
3143B
104136 Boom Antenna Mount Knob
Through boom on 7-TR, Mast
105861 Thread Insert
105861 Thread Insert
104169 Boom Antenna Mount Knob
Through boom on 7-TR, Mast
101913 Fixed Antenna Mount
Insert boom through
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
Biconical Antennas 3109
4-TR
7-TR, Mast
102308 Swivel Antenna Mount
104169 Boom Antenna Mount Knob
To antenna mounting hole
Stinger Mounts
2x2 Boom
4-TR – Do not mount to a 4-TR
106102 Universal Antenna Mount
To antenna mounting hole
Through boom on 7-TR, Mast
104136 Boom Antenna Mount Knob
7-TR – Mounts directly to a 7-TR without additional hardware
109042 – straight; for general antenna mounting on a 7-TR
Mast – Additional hardware required to mount to a mast
108983 – offset; for general antenna mounting on a 7-TR with pneumatic or manual polarization; can also be used to mount stinger-type antennas
3110C, 3110B, and 3104C antennas ship with these standard parts: 100733 Support Rod 101942B Support Base 102108 Clamp Block
Can mount directly to a 4-TR. Use of a 102308 Swivel Antenna Mount simplifies polarization, and is optional.
OR
102108 Clamp Block
Antenna shaft
Mast refers to 2070 Series, 2075, and 2175 Antenna Towers 2x2 Boom refers to a typical 2-inch by 2-inch boom; non-ETS-Lindgren and previous generation EMCO positioning systems
7-TR, Mast
4-TR 102108 Clamp Block
118947 – for stinger-type antennas only
Standard Parts
Through boom
3110C
7-TR refers to 109042, 108983, and 118947 booms:
Antenna balun
To 4-TR
3110C, 3110B, 3104C
Notes
OR
102108 Clamp Block
Antenna shaft
OR
102108 Clamp Block
Antenna shaft
2x2 Boom
106102 Universal Antenna Mount
Antenna shaft
OR
102108 Clamp Block
102108 Clamp Block
Antenna shaft
Antenna shaft
105861 Thread Insert
105861 Thread Insert
101913 Fixed Antenna Mount
101937 Swivel Antenna Mount
Antenna balun
102308 Swivel Antenna Mount
100733 Support Rod
3110B
To 4-TR
To 4-TR
105861 Thread Insert
104169 Boom Antenna Mount Knob
To 4-TR
104136 Boom Antenna Mount Knob
Through boom on 7-TR, Mast
101942B Support Base
3104C
105861 Thread Insert
Through boom on 7-TR, Mast
Insert boom through
Insert boom through
Can mount directly to a 4-TR. Use of a 102308 Swivel Antenna Mount simplifies polarization, and is optional.
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
Mini-Bicon Antennas 3109 3183, 3184 3181,
7-TR, Mast
4-TR
3181, 3184
113956 Antenna Mount Assembly
113956 Antenna Mount Assembly
Stinger
To 4-TR for horizontal mount (extension optional)
3183
113956 Antenna Mount Assembly
Stinger
For horizontal mount (extension optional)
Stinger
For vertical mount place 114669 spacer over extension
To 4-TR for vertical mount
About Mounts for 3181/3183/3184
2x2 Boom
For horizontal mount (extension optional)
3181, 3183, and 3184 ship with 113956 Antenna Mount Assembly, which includes the 114669 Spacer; no additional hardware required to mount to 4-TR
For vertical mount
Stinger Mounts
Notes
3181, 3183, 3184
7-TR refers to 109042, 108983, and 118947 booms: 109042 – straight; for general antenna mounting on a 7-TR
4-TR – See About Mounts for 3181/3183/3184
108983 – offset; for general antenna mounting on a 7-TR with pneumatic or manual polarization; can also be used to mount stinger-type antennas
7-TR, Mast, 2x2 Boom – Additional hardware required 3180, 3180B, 3182
118947 – for stinger-type antennas only
Standard Parts 104169 Boom Antenna Mount Knob Through boom
3180, 3182
101937 Swivel Antenna Mount
3180, 3180B, and 3182 ship with these standard parts: 100733 Support Rod 101942B Support Base
Insert boom through
102108 Clamp Block
Mast refers to 2070 Series, 2075, and 2175 Antenna Towers
4-TR / 7-TR – Mounts directly to a 4-TR or 7-TR without additional hardware
2x2 Boom refers to a typical 2-inch by 2-inch boom; non-ETS-Lindgren and previous generation EMCO positioning systems
Mast – Additional hardware required
3180 7-TR, Mast
4-TR 3180 with mini-cage elements
3180 with conical elements
102108 Clamp Block
OR
102108 Clamp Block
Stinger
102308 Swivel Antenna Mount
100733 Support Rod 3180B with conical elements
To 4-TR
101942B Support Base
3182 To 4-TR
102108 Clamp Block
Stinger
3180B
3180B with cage elements
OR
102108 Clamp Block
2x2 Boom OR
102108 Clamp Block
102108 Clamp Block
Stinger
Stinger
Stinger
105861 Thread Insert
105861 Thread Insert
105861 Thread Insert
105861 Thread Insert
104169 Boom Antenna Mount Knob
101913 Fixed Antenna Mount
101937 Swivel Antenna Mount
To 4-TR
Through boom on 7-TR, Mast
Insert boom through
Stinger
Insert boom through
Can mount directly to a 4-TR. Use of a 102308 Swivel Antenna Mount simplifies polarization, and is optional.
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
Log Periodic Antennas 3148B
Stinger Mounts
4-TR 100989 Polarizing Antenna Adapter
OR
101950 Support Rod To antenna mounting bracket, insert knob
To antenna mounting bracket, insert knob
To antenna mounting bracket, insert knob
105861 Thread Insert
105861 Thread Insert
101942B Support Base
To 4-TR
4-TR – Do not mount to a 4-TR
100989 Polarizing Antenna Adapter OR 106470 Non-Polarizing Antenna Adapter
OR
To 4-TR
Mast – Additional hardware required to mount to a mast
108983 – offset; for general antenna mounting on a 7-TR with pneumatic or manual polarization; can also be used to mount stinger-type antennas
105861 Thread Insert 100989 Polarizing Antenna Adapter Antennas include mounting bracket (attached) and mounting knob(s)
To 4-TR
118947 – for stinger-type antennas only Mast refers to 2070 Series, 2075, and 2175 Antenna Towers 2x2 Boom refers to a typical 2-inch by 2-inch boom; non-ETS-Lindgren and previous generation EMCO positioning systems
Can mount directly to a 4-TR. Use of a 102308 Swivel Antenna Mount simplifies polarization, and is optional.
3148 7-TR, Mast 100989 Polarizing Antenna Adapter OR 106470 Non-Polarizing Antenna Adapter
3147
109042 – straight; for general antenna mounting on a 7-TR
Antennas shown here ship with these standard parts:
3148, 3147, 3144
7-TR refers to 109042, 108983, and 118947 booms:
7-TR – Mounts directly to a 7-TR without additional hardware
Standard Parts
102308 Swivel Antenna Mount
Notes
To antenna mounting bracket, insert knob
104136 Boom Antenna Mount Knob
Through boom on 7-TR, Mast
OR
2x2 Boom
100989 Polarizing Antenna Adapter OR 106470 Non-Polarizing Antenna Adapter
100989 Polarizing Antenna Adapter OR 106470 Non-Polarizing Antenna Adapter
To antenna mounting bracket, insert knob
To antenna mounting bracket, insert knob
OR
100989 Polarizing Antenna Adapter OR 106470 Non-Polarizing Antenna Adapter
To antenna mounting bracket, insert knob
Mounting the Model 3186
105861 Thread Insert 101913 Fixed Antenna Mount
104169 Boom Antenna Mount Knob Insert boom through
101937 Swivel Antenna Mount
For complete information on mounting the Model 3186, see the Model 3186 Dual Stacked Log Periodic Dipole Array (LPDA) User Manual.
Insert boom through
Through boom on 7-TR, Mast
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
Double-Ridged Waveguide Horns 3106B
4-TR
3115
All Double-Ridged Waveguide Horns (except the 3106 Series and 3119) mount directly to a 4-TR. Mounting hardware is included; no additional hardware required.
OR
To antenna mounting hole
To antenna mounting hole
Do not mount the 3106 Series or 3119 to a 4-TR.
Stinger Mounts
2x2 Boom 2x2 Boom
7-TR, Mast
104169 Boom Antenna Mount Knob
101913 Fixed Antenna Mount
7-TR – Mounts directly to a 7-TR without additional hardware
101937 Swivel Antenna Mount
Mast – Additional hardware required to mount to a mast
108983 – offset; for general antenna mounting on a 7-TR with pneumatic or manual polarization; can also be used to mount stinger-type antennas 118947 – for stinger-type antennas only
Mast refers to 2070 Series, 2075, and 2175 Antenna Towers 2x2 Boom refers to a typical 2-inch by 2-inch boom; non-ETS-Lindgren and previous generation EMCO positioning systems
2
3116B
Remove wingnut, nuts, and screws from mount adapter; will re-use screws in step 4.
3116
Mount 3106B to 108507 Boom Note: Install the 108507 boom onto the 7-TR before performing these steps. For clarity, the 7-TR is not shown in the following illustrations.
1
3116C
Remove 104136 knobs and lift mount adapter from boom; will re-use in step 5.
3117
109042 – straight; for general antenna mounting on a 7-TR
(for 3106 Series only) 108507 – centerline rotation boom; when changing polarization, maintains centerline rotation
See Mount 3106B to 108507 Boom for the steps to mount a 3106 Series antenna to a 7-TR.
3116, 3116B, 3116C
7-TR refers to these booms:
Insert boom through
Insert boom through
Through boom on 7-TR, Mast
4-TR – Do not mount to a 4-TR
To antenna mounting hole
Notes
4 Re-insert/tighten screws through vertical part of mount adapter into two holes on antenna. Re-insert/tighten screw through horizontal part of mount adapter into mount block on antenna.
3119 3 Remove screws from side of 3106B with antenna connector.
5 Re-insert/tighten 104136 knobs to attach antenna and mount adapter to boom.
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
3164 Series Horns Open Boundary Quad-Ridged Horns 3164-05, -06, -07, -08, -10, -11
3164-06
3164-11
OR
Bracket Mount
To antenna mounting hole
Only the 3164-05 (108071 bracket) and 3164-11 (119430 bracket) can be mounted to a 4-TR.
3164-05
3164-07
7-TR, Mast
4-TR
Do not mount 3164-06, -07, -08, or -10 antennas to a 4-TR.
Bracket Mount
3164-10
Through boom on 7-TR, Mast
3164-08
To antenna mounting hole
105861 Thread Insert
105861 Thread Insert
104169 Boom Antenna Mount Knob
101913 Fixed Antenna Mount
Insert boom through
Through boom on 7-TR, Mast
For the type of bracket mount, see Standard Parts.
4-TR 106974 Mount
7-TR, Mast
2x2 Boom
106974 Mount
106974 Mount
To antenna mounting hole
To antenna mounting hole
7-TR refers to 109042, 108983, and 118947 booms: 109042 – straight; for general antenna mounting on a 7-TR
Mast – Additional hardware required to mount to a mast
108983 – offset; for general antenna mounting on a 7-TR with pneumatic or manual polarization; can also be used to mount stinger-type antennas 118947 – for stinger-type antennas only
108071 Mount – ships with 3164-05
Mast refers to 2070 Series, 2075, and 2175 Antenna Towers
106974 Mount – ships with 3164-06, 3164-07, 3164-08, and 3164-10
2x2 Boom refers to a typical 2-inch by 2-inch boom; non-ETS-Lindgren and previous generation EMCO positioning systems
119430 Mount – ships with 3164-11 105861 Thread Insert – ships with 3164-08 and 3164-10
About 3164 Mounts 3164-05 – ships with stinger for stinger-compatible mounts
To antenna mounting hole
105861 Thread Insert
Notes
7-TR – Mounts directly to a 7-TR without additional hardware
Standard Parts
For the type of bracket mount, see Standard Parts.
Dual-Polarized Horns 3164-03, -04
4-TR – Do not mount to a 4-TR
Bracket Mount
To antenna mounting hole
104136 Boom Antenna Mount Knob
See About 3164 Mounts.
Stinger Mounts
2x2 Boom
3164-05, -11 – ships with mounting hardware, no additional hardware required to mount to 4-TR, 7-TR, mast, or 2x2 boom 105861 Thread Insert
104136 Boom Antenna Mount Knob
101913 Fixed Antenna Mount
To 4-TR Through boom on 7-TR, Mast Insert boom through
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
Pyramidal Horn Antennas 3160 Series, 3161 Series
4-TR
Pyramidal horn antennas mount directly to a 4-TR; no additional hardware required. Do not mount 3160-01, 3160-02, and 3161-01 antennas to a 4-TR.
OR
To antenna mounting hole
To antenna mounting hole
104169 Boom Antenna Mount Knob
Through boom on 7-TR, Mast
About 3160 Mounts
2x2 Boom 2x2 Boom
7-TR, Mast
101913 Fixed Antenna Mount
Insert boom through
3160-09 and 3160-10 – ship with a supplemental mount that may be used with the 4-TR, 7-TR, mast, and 2x2 boom
To antenna mounting hole
101937 Swivel Antenna Mount
Insert boom through
Notes 4-TR: Do not mount large pyramidal horn antennas to a 4-TR. 7-TR refers to 109042, 108983, and 118947 booms: 109042 – straight; for general antenna mounting on a 7-TR 108983 – offset; for general antenna mounting on a 7-TR with pneumatic or manual polarization; can also be used to mount stinger-type antennas 118947 – for stinger-type antennas only Mast refers to 2070 Series, 2075, and 2175 Antenna Towers
See About 3160 Mounts.
See About 3160 Mounts.
See About 3160 Mounts.
2x2 Boom refers to a typical 2-inch by 2-inch boom; non-ETS-Lindgren and previous generation EMCO positioning systems
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
Dipoles 3121D
Stinger Mounts
4-TR 102108 Clamp Block
102108 Clamp Block
OR Antenna shaft
OR Antenna shaft
Antenna shaft
102308 Swivel Antenna Mount
100733 Support Rod Stinger
4-TR – Do not mount to a 4-TR
102108 Clamp Block
105861 Thread Insert
7-TR refers to 109042, 108983, and 118947 booms:
7-TR – Mounts directly to a 7-TR without additional hardware
109042 – straight; for general antenna mounting on a 7-TR
Mast – Additional hardware required to mount to a mast
108983 – offset; for general antenna mounting on a 7-TR with pneumatic or manual polarization; can also be used to mount stinger-type antennas
Standard Parts
118947 – for stinger-type antennas only
To 4-TR
To 4-TR
3121C
Notes
Antennas shown here ship with these antenna adapters: 100733 Support Rod
101942B Support Base
101942B Support Base 102108 Clamp Block
Mast refers to 2070 Series, 2075, and 2175 Antenna Towers 2x2 Boom refers to a typical 2-inch by 2-inch boom; non-ETS-Lindgren and previous generation EMCO positioning systems
Can mount directly to a 4-TR. Use of a 102308 Swivel Antenna Mount simplifies polarization, and is optional.
To 4-TR
7-TR, Mast OR
102108 Clamp Block
2x2 Boom
106102 Universal Antenna Mount
Antenna shaft
OR
102108 Clamp Block
102108 Clamp Block
Antenna shaft
Antenna shaft
105861 Thread Insert
105861 Thread Insert
101913 Fixed Antenna Mount
101937 Swivel Antenna Mount
Antenna balun
105861 Thread Insert
104169 Boom Antenna Mount Knob
104136 Boom Antenna Mount Knob
Through boom on 7-TR, Mast Through boom on 7-TR, Mast
Insert boom through
Insert boom through
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
Loop Antennas and Rod Antennas Loop Antennas
4-TR
Loop antennas and rod antennas mount directly to a 4-TR; no additional hardware required.
OR
To antenna mounting hole
To antenna mounting hole
104169 Boom Antenna Mount Knob
Through boom on 7-TR, Mast
About 3301C
2x2 Boom 2x2 Boom
7-TR, Mast
101913 Fixed Antenna Mount
Insert boom through
4-TR Light Tripod – To comply with the MIL-STD-461F standard, a smaller tripod (4-TR,1ML) is available (optional).
To antenna mounting hole
101937 Swivel Antenna Mount
Insert boom through
MIL-STD-461F Kit – To comply with the standard, a cable and grounding kit (113359) is included with the 3301C.
Notes 7-TR refers to 109042, 108983, and 118947 booms: 109042 – straight; for general antenna mounting on a 7-TR 108983 – offset; for general antenna mounting on a 7-TR with pneumatic or manual polarization; can also be used to mount stinger-type antennas 118947 – for stinger-type antennas only Mast refers to 2070 Series, 2075, and 2175 Antenna Towers 2x2 Boom refers to a typical 2-inch by 2-inch boom; non-ETS-Lindgren and previous generation EMCO positioning systems
Rod Antennas 3301C
See About 3301C.
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
Conical Log Spirals 3101
4-TR
7-TR, Mast
Notes
2x2 Boom
7-TR refers to 109042, 108983, and 118947 booms: 109042 – straight; for general antenna mounting on a 7-TR
Conical log spirals mount directly to a 4-TR; no additional hardware required.
Conical log spirals mount directly to a 7-TR. Mounting hardware is included; no additional hardware required.
Conical log spirals not intended for 2x2 boom.
108983 – offset; for general antenna mounting on a 7-TR with pneumatic or manual polarization; can also be used to mount stinger-type antennas
Standard Parts 101942B Support Base – ships with 3101, 3102, and 3103
3102
101941 Support Rod with 3101
– ships
101943B Support Rod with 3102 101944 Support Rod with 3103
– ships
– ships
118947 – for stinger-type antennas only Mast refers to 2070 Series, 2075, and 2175 Antenna Towers 2x2 Boom refers to a typical 2-inch by 2-inch boom; non-ETS-Lindgren and previous generation EMCO positioning systems
3103
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
High Gain Conical Horns 3163 Series -03, -04, -05, -06
4-TR
OR
To antenna mounting hole
To antenna mounting hole
About 3163 Series
2x2 Boom 2x2 Boom
7-TR, Mast
To antenna mounting hole
Each Model 3163 Series includes a built-in 1/4–20 thread mount.
3163-03
3163-04
3163-05
3163-06
Model 3163 Series horn antennas mount directly to a 4-TR; no additional hardware required.
104169 Boom Antenna Mount Knob
Through boom on 7-TR, Mast
101913 Fixed Antenna Mount
Insert boom through
101937 Swivel Antenna Mount
Insert boom through
The backplate on each Model 3163 Series provides threaded holes for mounting directly into the feed section of a tapered chamber. Additionally, you can use the threaded holes to create your own custom mounting solution. See the 3163 manual for a diagram of each backplate.
Notes 7-TR refers to 109042, 108983, and 118947 booms: 109042 – straight; for general antenna mounting on a 7-TR 108983 – offset; for general antenna mounting on a 7-TR with pneumatic or manual polarization; can also be used to mount stinger-type antennas 118947 – for stinger-type antennas only Mast refers to 2070 Series, 2075, and 2175 Antenna Towers 2x2 Boom refers to a typical 2-inch by 2-inch boom; non-ETS-Lindgren and previous generation EMCO positioning systems
www.ets-lindgren.com