Model CB-HAND Locking Handle Kit Corrosion Resistant Lightweight Components Push-Button Release

Applications: Designed for mobile applications where lock-in and lock-out provide a measure of safety. Compatible with slide models 7950, 7957, 9301, and other slides with cross sections measuring .75" [17.5mm] and above.

0.88 [22.5] 1.57 [40.0]

0.79 [20.0]

5.31 [135.0]

Lock-in Kit CBHAND-2

1.97 [50.0]

.75 [19.0]

5.31 [135.0]

.18 [4.5]

1.06 [27.0]

1.57 [40.0]

12.60 [320.0] 0.75 [19.0]

1.50 [38.0]

1.38 [35.0]

.078 [2.0]

Lock Block 14.37 [365.0] 1.57 [40.0]

1.18 [30.0] 4.62 [117.5]

0.30 [7.5]

1.38 [35.0]

0.65 [16.5]

1.06 [27.0]

13.48 [342.4]

0.67 [17.0]

0.98 [24.8]

1.38 [35.0]

0.65 [16.5]

0.67 [17.0]

14.37 [365.0] 1.57 [40.0]

1.18 [30.0]

1.40 [35.7]

4.62 [117.5]

0.67 [17.0]

0.67 [17.0]

Lock-out Kit CBHAN4-5

1.06 [27.0]

13.48 [342.4]

0.67 [17.0]

0.65 [16.5]



Rod Support Block

0.79 [20.0]

0.30 [7.5]

1.38 [35.0]

0.79 [20.0]

Locking Options

0.98 [24.8]

0.67 [17.0]

1.38 [35.0]

0.65 [16.5]

Front mounted unit – lock-in only (CBHAND-2) Rear mounted unit – lock-out (requires P/N CBHAN4-5) Note: The addition of the lock out conversion kit requires an additional threaded bar to connect push buttons (not included).

Rod Lengths Material Thickness Load Rating Hardware

19.7" [500mm] rods, applications up to 44" [1122mm] wide (CBHAN3-0100-2) 29.5" [750mm] rods, applications up to 64" [1622mm] wide (CBHAN3-0150-2) Maximum material thickness on drawer front = ½" [12 mm] Dependent on slides used M5 screws (not included)

NOTE: Lock-out not intended for use with over travel slides.

inch mm



Installation Instructions Note: Although SAE dimensions have been noted, in some cases, the metric dimensions provide greater accuracy.

Cutting the rods

31.93 [811.0] max

1. Select the length of rod based on the drawer width. To determine rod length (See figure 1):

0.69 [17.5]

Using Accuride Lock Block: Cavity/cabinet width (B) – 4.81 [122.3mm] ÷ 2 Without Accuride Lock Block: Lock to lock – 3.52 [89.3mm] ÷ 2 2. Using a 3mm or #32 drill bit, drill a hole 8mm [.315"] from the end of each rod section. It is recommended a drill press and center-finder for round stock is used for this operation. (See figure 2)

1.50 [38.0]

62.48 [1587.0] max

3. The rod ends opposite of the holes should be chamfered or rounded to ease movement in and out of the lock block segments of the assembly. C = (B-4.81 [122.3]) / 2

0.51 [13.0]

C500 = CBHAN-0150-2

0.14 [3.5]

0.79 [2.0]

0.59 [15.0]

Figure 1

Figure 2

Drawer Box Prep Handle and mechanism mounted below drawer box

C

Lock-in mounting 1. Drill fixing and push-button holes for the handle, mechanism, and bar support blocks (see figure 3a). The material thickness should not be greater than .5" [12mm] or the push button will not operate properly. Important: The height of handle assembly is 1.5" [38mm]. The horizontal center of the assembly must be located at least .75" [19mm] below the bottom of the drawer to provide clearance for the mechanism and rod.

B Dimensions 0.39 [10.0] 0.33 B [8.5] A

0.75 C [19.0] min D 6.30 [160.0]

D A

A

D

B

Figure 3a

Lock-in and Lock-out mounting 1. Drill fixing and push-button holes to mount handle, mechanism, and bar support blocks. See figure 3b for hole locations. The material thickness should not be greater than .5" [12mm].

For installations where the handle is positioned on the front of the drawer box, with the mechanism inside, see Figure 7b.

C

D Dimensions 0.39 [10.0] 0.33 B [8.5]

D

E

C

A

0.75 C [19.0] min D 0.98 [25.0] 6.30 E [160.0]

Figure 3b

E

A

B

E A

E A A

B



Installation Instructions Lock Block Installation - Lock-in/Lock-out 1. Drill fixing holes for the lock blocks. See Figure 4a (lock-in only) or Figure 4b (additional lock-out). The center of the lock block should line up with the centerline of the fixing holes for the handle and mechanism. The center of the rod = center of the lock block hole.

A

C

The center of the rod is .30" [7.5mm] from the front edge of the mechanism. The lock block will sit slightly closer to the front of the cabinet.

Dimensions A

A

B

Note: The lock blocks must be located a minimum of .24" [6mm] below the outer member of the slide if it is positioned flush at the bottom of the drawer. See Figure 1a for engagement and clearance dimensions if you are not using the Accuride lock blocks.

B

0.24 [6.0] min

1.10 B [28.0] C

0.75 C [19.0]

Figure 4a

2. Install lock blocks. Fasteners are chosen based on cabinet/ case material. (Figure 5a)

B

A

C

B

B

Dimensions

C

A

A

0.24 [6.0] min

1.10 B [28.0] 0.75 C [19.0]

Figure 4b

C

Figure 5a 3. For lock-out installations, measure and drill holes in the base of the drawer for the rod guide bracket (Figure 5b).

A

A

B

Dimensions 0.39 A [10.0]

Figure 5b

C



Installation Instructions Mechanism Assembly 1. Insert the rods into the handle mechanism (Figure 6a). Figure 6a 2. Install pins by tapping into place. Ensure that pins are flush or underflush (Figure 6b).

3. Thread bar support blocks on to the rods (Figure 6c).

Figure 6b

Figure 6c

Handle and Mechanism Installation Lock-in only 1. Using M5 fasteners, install the mechanism, push button, and double handle to front of drawer as shown in Figure 7a.

Figure 7a 2. The lock mechanism may also be installed inside the drawer. Care must be taken with the measurements to ensure the mechanism (with rods attached) can be installed into the space and operate without interference (Figure 7b).

A Dimensions A

0.39 [10.0]

B

6.30 [160.0]

0.75 C [19.0] min D 0.30 [7.5]

Figure 7b 3. The locking rod must be measured carefully from the inside of the drawer side so that it extends a maximum of 1.22" [31mm] (Figure 7c).

Figure 7c

A

B D B

C



Installation Instructions Handle and Mechanism Installation Lock-out kit 1. The lock-out feature requires a customer-supplied 10mm rod threaded to M10 for a minimum of .98" [25mm] at each end to connect push buttons (Figure 8a). 2. To determine rod length, measure from the outside of the drawer front to the front edge of the rear push button. Length of rod = D + 1.97" [50mm]. 0.98 [25.0 mm]

D

0.98 [25.0 mm]

Length of rod = D + 1.97" [50mm]

M10

Figure 8a 3. Fit handle to front of drawer. Insert front push button and screw in the 10mm rod. Push rod guide-block on to the rod. Insert rear button through hole in rear of drawer and screw into the 10mm rod. Attach mechanism to rear of drawer. Fix lock rod support blocks and 10mm rod guide bracket (Figure 8b).

Figure 8b



Packaging & Availability CBHAND –  2 includes the handle components and lock mechanism for lock-in only. To add the lock-out function, a separate conversion kit is required.

Lock-out Kit — CBHAN4-5 Lock Block

Center Rod Seat

Rod Support Block

Stainless Steel Rods CBHAN3-0XXX-2

Lock Block

Lock Mechanism

Center Rod Guide Block

Lock Pin

Lock Block

Rod Support Block

Lock Pin

Push Button Composite Handle

Lock Block

Lock-in Kit — CBHAND-2

Part Number

Description

Components

CBHAND-2

Handle Kit w/ lock-in

1 - handle, mechanism, and push button 2 - bar support blocks, lock blocks, and pins

CBHAN3-0100-2

Stainless Steel Rods

2 - 19.7" [500mm] rods

CBHAN3-0150-2

Stainless Steel Rods

2 - 29.5" [750mm] rods

CBHAN4-5

Lock-out Conversion Kit

2 - push buttons and lock blocks 1 - guide bracket

Order example

Specifications

Lock-in + Lock-out conversion kit:

Rods: Stainless Steel

Qty CBHAND-2 1 ea.

Handle and Mechanism: Metal / Polymer

CBHAN3-0150-2 1 ea.

Note: Specifications, materials, prices, terms and delivery are subject to change without notice.

CBHAN4-5 1 ea.

RoHS compliant

ACCURIDE INTERNATIONAL INC.

For the most current technical information, visit www.accuride.com

12311 Shoemaker Avenue Santa Fe Springs, CA 90670 TEL (562) 903-0200 FAX (562) 903-0208 www.accuride.com Manufacturing, Engineering, and Sales United States • Germany • Japan • Mexico • United Kingdom • China 3700-9544 (1243)-MK974-N-0412