90-20-0121_AK0, Technical manual, Microtower
Microtower
Technical manual
1
About this manual About the contents of this manual
The information in this document may be changed at any time without notice .
Table of Contents About this manual
2
About the contents of this manual
2
Table of Contents
2
Version and revision history.
4
Revision history for this document.
4
General description Functional Configuration alternatives.
5 5 9
Products.
9
60-00-5774 Microtower Bas1 USB2 RÖS
10
60-00-5775 Microtower SCSI RÖS
10
60-00-5859 Microtower Bas2 USB2 RÖS
11
60-00-5861 Microtower Bas3 USB1 RÖS
11
60-00-5999 Microtower Bas4 USB2 RÖS
12
Hard disc caddies
13
Hard disk cradle
13
DVD ± RW Double Layer 16X IDE
14
Floppy disc drive 3,5” USB
14
Hewlett Packard SureStore DAT8
14
Smart Card-reader Omnikey Cardman 3121 USB
15
PC-Card “cradle” for crypto card KK672
15
Fiber cables.
15
Technical data
16
2
Microtower
16
Fiber optics and data protocols
16
Power Supply.
16
Hard disc drive (60-00-5881)
16
DVD-burner
16
Floppy disc drive USB
17
Smart Card Reader
17
HP SureStore DAT8
17
PC-card USB cradle for KK672
17
Physical dimensions and weight
17
Environmental
17
Unpacking. Installation.
18 19
Installation of RÖS-material.
19
Power supply
19
Serial number.
19
Fiber interface Microtower, SCSI, USB1.1 or USB 2.0.
20
Tampering protection cover.
21
Configuration Configuring PC / computer.
22 22
BIOS.
22
Operating system – hardware drivers.
22
Säkerhet.
22
Start och användning.
23
Uppkoppling.
23
Spänningsanslutning.
23
Byte av media.
23
Teknisk support CE - märkning
24 24
Version and revision history. Revision history for this document. Revision AK0. 2006-09-29, AnNy, document created. Revision R0. 2006-09-29, AnNy, document released. Document properties. Last saved: 10/12/2006 5:31:00 PM Filename: 90-20-0121_AK0, Technical manual, Microtower Author. Created by Anders Nyström. Last saved by Anders Nyström.
4
General description Functional
Microtower
Microtower is a unit for peripheral devices communication via fiber optics with the computer. The Microtower is approved for use in compliance with the Swedish RÖS U1 regulations. Microtower can be configured with up to three 5.25” standard devices . Example of peripheral devices: DVD/CD RW Floppy Disc Drive Memory Card Reader Smartcard-Reader PC-card Hard Disc Drive One standard 5.25” standard slot can be shared by physical smaller devices. Fiber optics is used for communication between computer and Microtower, with either USB1.1, USB2.0 or SCSI as protocol. SCSI is mainly used for computers with operating systems not supporting USB. Emanation protection is achieved mainly by tight Faraday cages. The intention is that system and mechanics easily can be modified and updated for future needs of new devices and functions. The computer can be one of Fibersystems RÖS U1 approved types, or a computer connected via Fibersystems RÖS U1 approved DVI workstation, (USB1.1), or any other computer connected via Fibersystems USB to fiber links, for example 45-331. Microtower can also be connected to other computers/devices using Icron fiber protocol for USB1.1 or USB2.0. 5
Applications Microtower with USB1.1 protocol.
Microtower
2xFiber 2 x fiber
45-3xx
USB1.1
Workstation
PC Shielded Contol room
DVI workstation with Microtower
KVM-extender with Microtower
6
Microtower with USB2.0 protocol.
21”PC workstation with Microtower
Workstation PC Gen IX
2xFiber
Microtower
PC Gen IX RÖS U1 with Microtower
7
2xFiber Microtower
45-331
USB2.0 45-3xx
Workstation
PC Shielded Computer Room
DVI RÖS U1 with Microtower for USB2.0
The USB to fiber converter 45-331 can be connected to any computer with an USB2.0 port. This function/product can also be used in applications without RÖS-demands, in order to move peripheral devices at a distance from the computer. For example for daily backup-tape device easily accessible by reception desk or for the security responsible persons workplace while the computer /server is placed in a server room. Microtower with SCSI protocol.
21”PC workstation 60-00-5772 with Microtower 60-00-5775
8
Configuration alternatives. Depending on application, fiber protocol and types of peripheral devices, several different types of Microtowers are available.
Products.
Microtower-unit.
The following Microtower units are available: 60-00-5774 Microtower Bas1 USB2 RÖS 60-00-5775 Microtower SCSI RÖS 60-00-5859 Microtower Bas2 USB2 RÖS 60-00-5861 Microtower Bas3 USB1 RÖS, (Note! only USB1.1)
60-00-5999
Microtower Bas4 USB2 RÖS
9
60-00-5774 Microtower Bas1 USB2 RÖS
Microtower 60-00-5774 communicate with USB2.0 via fiber. Two peripheral devices are mounted: 1. DVD±RW/RAM Double Layer16X IDE 2. Sony floppy disc drive 3,5" USB. Third device slot is empty.
60-00-5775 Microtower SCSI RÖS
Microtower 60-00-5775 communicate with SCSI via fiber. Intended to be used with 21” PC, 60-00-5772. Three peripheral devices are mounted: 1. DVD±RW/RAM Double Layer16X IDE (Connected via an ATAPI to SCSIconverter). 2. Hewlett Packard DAT8 tape recorder. 3. Floppy disc drive SCSI 1.44MB.
10
60-00-5859 Microtower Bas2 USB2 RÖS
(Not yet RÖS-approved). Microtower 60-00-5859 communicate with USB 2.0 via fiber. Three peripheral devices are mounted: 1. DVD±RW/RAM Double Layer16X IDE (Connected via an ATAPI to USBconverter). 2. Sony floppy disc drive 3,5" USB. 3. Smartcard reader Omnikey CardMan 3121 USB.
60-00-5861 Microtower Bas3 USB1 RÖS
Microtower 60-00-5861 communicate with USB1.1 via fiber. This product is mainly intended to be used with Fibersystems RÖS U1 approved DVI workstation. It can also be used with other units using Icron USB1.1-fiber optic protocol, for example Fibersystem’s KVMX-links. Three peripheral devices are mounted: 1. DVD±RW/RAM Double Layer16X IDE. 2. Sony floppy disc drive 3,5" USB. 3. Smartcard reader Omnikey CardMan 3121 USB.
11
60-00-5999 Microtower Bas4 USB2 RÖS
Microtower 60-00-5999 communicate with USB2.0 via fiber. Three peripheral devices are mounted: 1. 2 x USB2.0 typ A. For example for USB-memory stick. 2. Hard disc cradle for removable Fibersystem 2,5” hard disc caddy system. 3. PC-card ”cradle” from Sectra for crypto card KK672. Hard disc caddies are ordered separately.
12
Hard disc caddies Microtower can be delivered with removable hard discs in form of a cradle and a caddy. Hard disc caddies are available as accessories. Available hard disc caddies: 60-00-5881 HDD 2,5" 80GB caddy complete 60-00-5972 HDD 2,5" 100GB caddy complete 60-00-5973 HDD 2,5" 120GB caddy complete
Hard disc caddy
Hard disk cradle
Hard disc cradle for Fibersystems 2,5” Hard disc caddies.
13
DVD ± RW Double Layer 16X IDE
Super Multi-burner from LG managing all DVD-formats, "plus", "minus", "RAM" and Dual Layer in both "plus" and "minus" enabling storage of data up to 8.5 GB on one side. The DVD-burner is able to write at 16x speed with PCAV-technology wich makes it possible to write a full DVD-R in 5 minutes. IDE-interface. For USB an IDE to USB converter is used. For SCSI an IDE to SCSI converter is used.
Floppy disc drive 3,5” USB
Floppy disc drive 3,5” with USB-interface.
Hewlett Packard SureStore DAT8
DAT tape recorder. SCSI-interface.
14
Smart Card-reader Omnikey Cardman 3121 USB
Reader for Smart Card. USB-interface.
PC-Card “cradle” for crypto card KK672
Without PC-card.
With PC-card - Smart Card reader
PC-card with USBinterface from Sectra for crypto card KK672.
Fiber cables. The Microtowers are equipped with fiber interfaces for connection of multimode fibers. All fiber optic connections are of type LC.
15
Technical data Microtower Standard 5,25” Device Slots
3
Fiber optics and data protocols Transmission Speed
(The peripheral devices are factory mounted and can only be changed at factory. After exchange the Microtower must be sent for investigation and sealing by certified organistion).
USB1.1 – Icron protocol, 16Mbit/s USB2.0 – Icron protocol, 600Mbit/s SCSI – Fibersystem protocol
Optical data Wavelength
USB2.0, SCSI - 850nm
Fiber Optic Connector Type
LC
Optical System Budget
USB2.0 – 10dB SCSI – 10dB (all with multimode fiber, (62.5/125 um)
Typical Distance
USB2.0 SCSI
– –
0-500m 0-2000m *
(*at large distances the overall transmission speed will decrease due to the protocols handshake process).
Power Supply. 230V AC, 50Hz, + 20%. Connector Power
IEC 320, 3 pin.