RAPTOR RF concentrator / Media coupler Application instructions Woertz AG Hofackerstrasse 47 Postfach 948 CH-4132 Muttenz 1 Tel. +41 61 466 33 33 Fax +41 61 461 96 06 [email protected] www.woertz.ch

Application instructions "RAPTOR RF Concentrator / Media Coupler" (Art. 49596)

1. How does it operate?

The RF input concentrator / Media coupler of the Raptor series allows the RF push button to be connected to the KNX Bus via a unidirectional RF connection. The RF input concentrator can be programmed by means of the ETS3 software and provides 32 channels. Each channel can be individually configured. The main functions are: dimming, shutter / blind control, heating, priority, timer, value and scene. The antenna is located within the housing. The concentrator can therefore easily be mounted on the flat cable.

Version v00, 24/02/10

2 / 15

Application instructions "RAPTOR RF Concentrator / Media Coupler" (Art. 49596)

2. ETS Parameters The different functions are explained below on the base of the ETS3 Software. The database of the device can also run on ETS2 Software.

2.1. Menu General Here you can select the main operating mode of the device. Different or advanced parameters are available according to the chosen mode.

This parameter defines for the dimmer and shutter/blind function the detection time of a hold down pressure. Values: 400 ms. 500 ms, 600 ms, 700 ms, 800 ms, 900 ms, 1s. Default value: 500 ms

Version v00, 24/02/10

3 / 15

Application instructions "RAPTOR RF Concentrator / Media Coupler" (Art. 49596)

2.2. Menu Channels and communication objects From channel 1 to 32 the menu is identical. When loading the application under ETS3 following functions are available.

2.2.1 Functions: ON / OFF, Toggle and Timer These functions allow the lighting circuit or any other load to be switched ON or OFF.

2.2.11 Function: ON / OFF

The ON / OFF parameter defines the commands to be sent when pressing and releasing the pushbutton of the RF input or the pushbutton connected with the RF input.

ON /-, OFF/-, ON / OFF, OFF / ON, - / ON, - / OFF. Default value: ON / Command when pressing / Command when releasing (“ - “ = No action).

2.2.12 Function: Toggle

The Toggle parameter defines the commands to be sent when pressing and releasing the pushbutton of the RF input or the pushbutton connected with the RF input. Toggle / -, Time delayed remote switch / -, - / Toggle. Default value: Toggle / Command when pressing / Command when releasing (“ - “ = No action).

Version v00, 24/02/10

4 / 15

Application instructions "RAPTOR RF Concentrator / Media Coupler" (Art. 49596)

2.2.13 Function: Timer

For each channel, it is possible to select the Timer function.

2.2.2 Function: Dimming This function allows a light using one or two pushbuttons to be dimmed.

2.2.21 Function: Dimming using one pushbutton The Dimming parameter allows the using mode to be selected. Values: 1-button dimmer or 2-button dimmer. Default value : Variation 1 button

1-button dimmer

Version v00, 24/02/10

5 / 15

Application instructions "RAPTOR RF Concentrator / Media Coupler" (Art. 49596)

2.2.22 Function: Dimming using two buttons

The Dimming parameter allows the using mode to be selected. Values: 1-button dimmer or 2-button dimmer. Default value : Variation 1 button 2-button dimmer (Dim up, Dim down) This parameter defines the dimming direction associated with the pushbutton, Values: Dim up or Dim down. Default Value: Dim up

2.2.3 Function: Shutters / Blinds This function allows a shutter or a blind using one or two buttons to be controlled. 2.2.31 Function: Shutters / Blinds with one button

The Shutters / Blind parameter allows the using mode to be selected: Function: 1-button control or 2-button control. Default value: 1-button control 1-button control (Up, Down)

Version v00, 24/02/10

6 / 15

Application instructions "RAPTOR RF Concentrator / Media Coupler" (Art. 49596)

2.2.32 Function: Shutters / Blinds with two buttons and press for a long time

The Shutters / Blinds parameter allows the using mode to be selected: Function: 1-button control or 2-button control. Default value: 1-button control 2-button control (Up, Down) or press for a long time (Safety)

This parameter defines the movement associated with the button. Up/Down or Down. Default value : Up/Down.

2.2.4 Function: Heating This function allows a heating or air-conditioning set-point to be selected.

This parameter allows the set-point associated with the button to be selected. Comfort, Economy (Reduced), Frost protection, Auto or Absence (Stand-by). Default value: Comfort

Version v00, 24/02/10

7 / 15

Application instructions "RAPTOR RF Concentrator / Media Coupler" (Art. 49596)

2.2.5 Function: Priority This function allows priority start or priority stop controls to be sent.

This parameter allows a Priority type to be selected. It depends on the type of application. ON priority, OFF priority. Default value: ON priority.

2.2.6 Function: Scene This function allows a scene to be created.

Function Scene This parameter defines the scene number. Scene 1 to scene 32. Default value: Scene 1 This parameter authorizes or forbids the learning of the scene. Authorized or Inhibited (Forbidden). Default value: Authorized

Version v00, 24/02/10

8 / 15

Application instructions "RAPTOR RF Concentrator / Media Coupler" (Art. 49596)

2.2.6 Function: Value This function allows different values to be sent.

The Value parameter defines the kind of value to be sent. Value type: Value in %, Temperature, Luminosity level, Brightness value, Value. Possible values: - Value in %: 0% to 100% by steps of 1%. Default value : 0% - Temperature: 0°C to 40°C by steps of 0.5°C. Default value : 20°C - Luminosity level: 0 lux to 1000 lux by steps of 50 lux. Default value : 300 lux - Brightness value: 0% to 100% by steps of 1%. Default value : 0% - Value: 0 to 65535 by steps of 1. Default value : 0.

Version v00, 24/02/10

9 / 15

Application instructions "RAPTOR RF Concentrator / Media Coupler" (Art. 49596)

3. RF configuration

The unidirectional RF inputs of the Raptor RF concentrator / Media coupler can be configured by means of a plug-in integrated in the ETS3 Software. It is first necessary to add the Raptor RF concentrator / Media coupler in your project. Click with the right mouse button on the concentrator to be configured. Then click on « RF configuration » (see picture below).

Version v00, 24/02/10

10 / 15

Application instructions "RAPTOR RF Concentrator / Media Coupler" (Art. 49596)

3.1 RF Configuration screen:

- The Fold window contains all inputs (32 Inputs). - The Available RF Inputs window contains all unidirectional RF inputs learned by the RF concentrator / Media Coupler. - The Linked RF Inputs of current fold window contains, if applicable, all unidirectional inputs linked with the selected channel. - The > button allows to erase one or more unidirectional inputs associated with a channel in case of a wrong association. - The Label button allows a unidirectional RF input (serial number, group address and designation) to be edited. - The Insert button allows a unidirectional RF input to be manually inserted. - The Remove button allows one or more unidirectional inputs to be erased from the interface. - The Learn RF button allows one or more unidirectional RF inputs to be stored. - The Cancel button allows to return to the ETS menu. - The Download button allows the configuration contained in the RF concentrator / Media coupler to be read. - The Upload button allows the configuration (channels, RF inputs association) to be downloaded into the RF concentrator / Media coupler (the configuration contained in the RF concentrator / Media coupler will be overwritten when downloading). - The Unload RF links button allows the download configuration to be erased. - The OK button allows the whole configuration to be confirmed and to be stored in the ETS project (pressing the OK button will not download the configuration into the ETS)

Version v00, 24/02/10

11 / 15

Application instructions "RAPTOR RF Concentrator / Media Coupler" (Art. 49596)

3.2 Learning one or more unidirectional RF inputs:

- Click on the Learn RF button - The following screen will be displayed:

- Press on the RF pushbuttons you want to connect to one or more RF inputs of the RF input concentrator / media coupler (for example: 000946400207 0/0/014) - All unidirectional RF inputs will then be displayed in the Available RF inputs window.

Version v00, 24/02/10

12 / 15

Application instructions "RAPTOR RF Concentrator / Media Coupler" (Art. 49596)

3.3: Adding manually a unidirectional RF input in the interface - Click on the Insert button. - The following screen will be displayed:

- In the field « Serial number » insert the number of the unidirectional RF input. Format: hexadecimal 12 digits. - In the field « Group address » insert the group address of the unidirectional RF input. Format: xx/yy/zzz (from 0/0/1 to 7/7/255). - If required, fill in a description of the input in the Designation line. Format: text, 20 characters maximum recommended because of the legibility of the elements in the window.

Example of manual insertion of a unidirectional RF input:

-

Version v00, 24/02/10

13 / 15

Application instructions "RAPTOR RF Concentrator / Media Coupler" (Art. 49596)

4. Example of applications

Version v00, 24/02/10

14 / 15

Application instructions "RAPTOR RF Concentrator / Media Coupler" (Art. 49596)

5. Specifications Standard

EMC

Article number

49596

Degree of protection Power supply

IP30 30V DC via KNX Bus

Transmission frequency

868.3MHz

Operating temperature

from 0°C to +45°C

Installation temperature

higher than +10°C

Weight Suitable cable

Version v00, 24/02/10

0.25 kg ecobus combi 49945

15 / 15