List of ComAp abbreviations and terms

Application Sheet

Copyright © 2007 ComAp a. s. Prague, Czech Republic

ComAp a. s. Kundratka 2359/17, 180 00 Praha 8, Czech Republic Tel: +420 246 012 111, Fax: +420 246 316 647 E-mail: [email protected], www.comap.cz

Abbreviation/term # ADN AFR AFS AG AHI AI AIC AID AIL AIM AIP ALI AMF ANT AO AS AST ATS AVR BB BF BI Bld BO BOC BTB C/O CAN1 CAN2

Description Setting of setpoints (with this character in front of them) is shared between controllers via intercontroller CAN2 Archive Drive Nano Air Fuel Ratio - method of control of lean burn gas engines AFR algorithm for stoichiometric gas engines AirGate - connection technology to make access to the internet as simple as possible Alarmlist&History Indication - protection type (see InteliGen/InteliSys Reference Guide for details) Analog Input InteliCompact New Technology archive file Archive ID-DCU InteliLite and InteliLite New Technology archive file Archive ID-Mobile InteliPro archive file Alarmlist Indication - protection type (see InteliGen/InteliSys Reference Guide for details) Auto Mains Failure (controller starts automatically on mains failure) IG/IS-NT archive file (contain setpoints, values, history and configuration saved from the particular controller) Analog Output All Speed application in ID-DCU and ID-Mobile controllers Archive Set - file created by InteliMonitor, contain links to archives from all active gensets of the site which were saved at the same time Automatic Transfer Switch (switches load to supplied bus (by mains or generators)) Automatic Voltage Regulator Base Box - controller unit mounted inside of switchboard (without built-in display) BiFuel / DualFuel - engine operation using combination of both diesel and gas Binary Input Baseload - gen-set power control mode which keeps constant power supply to the load Binary Output Breaker Open & Cool-down - protection type (see InteliGen/InteliSys Reference Guide for details) Bus-Tie Breaker Close/Open CAN bus for ComAp extension modules (e.g. IGS-PTM) and engine ECU connection (also called peripheral CAN bus) CAN bus for communication between ComAp controllers and communication modules connection (e.g. I-LB+) (also called intercontroller CAN bus)

CB Cfg COX CT DDE Del Derating

DHCP

Circuit Breaker Controller configuration Application for Complex Systems where actions are taken by a PLC and controller only follows orders => needs an external driver (cox) Current Transformer Dynamic Data Exchange (DDE server - communication server for most ComAp controllers) Delay Controled reduction of gen-set(s) power based on relevant value, e.g. temperature Dynamic Host Configuration Protocol - network protocol used to configure devices that are connected to a network (known as hosts) so they can communicate on that network using the Internet Protocol (IP)

DISTBIN

DISTributed Binary INPuts - virtual module for receiving binary signals from other IG/IS-NT controllers on CAN bus (supported from v.3.0)

DISTBOUT

DISTributed Binary OUTputs - virtual module for sending binary signals to other IG/IS-NT controllers on CAN bus (supported from v.3.0)

DC DE DM DNC DNF

DriveConfig - PC software for configuration of ID controllers DriveEdit - PC software for ID-Nano configuration DriveMonitor - PC software for monitoring of ID controllers ID-Nano import package ID-Nano Firmware

DNS

Domain Name System - hierarchical distributed naming system for computers, services, or any resource connected to the Internet or a private network

DT-KIT E ECU EFC EFCPM EFI EP ESC ESF

Input/Output Simulator for InteliDrive Family Controllers Electric protection - protection type (see InteliGen/InteliSys Reference Guide for details) Engine Electronic Control Unit Eart Fault Current Eart Fault Current Protection Module Electronic Fuel Injection Electronic Potentiometer Coded Engine Specific File Engine Specific File - defines inputs and outputs for controller communication with ECU (part of ECU list)

Engine Specific List - list of electronic engines supported by particular controller (part of ECU list) FD Feedback FDR Feeder application for IM-NT controller Fls Fail sensor FMI Failure Mode Identifier Forward synchronisation Synchronisation of unloaded genset to mains (GCB closing process) ESL

FPC FV GC GC GCB GeCon GL HST CHP IA-NT I-AOUT8 IB

Fire Pump Controller Force Value - function which enables to change setpoint value by activating/deactivating binary input Graphical Characters - controller option for additional support of one "graphical" language GenConfig - PC tool for configuration of IG/IS-NT controllers Generator Circuit Breaker GEnerator CONtroller - software modification of IG/IS-NT controller for control of generator part of gen-set only Gen-set Loaded History record - protection type (see InteliGen/InteliSys Reference Guide for details) Combined Heat & Power - cogeneration application, usually with gas engine InteliATS New Technology automatic transfer switch controller Extension module with 8 AO for IG/IS-NT and ID controllers Internet Bridge

IBF-2

Bi-Fuel/dual-fuel control system package which enables 4 stroke diesel engines, generating sets or pumps to operate on Bi-fuel/dual-fuel (for max. 6 cylinders engines)

IBF-20

Bi-Fuel/dual-fuel control system package which enables 4 stroke diesel engines, generating sets or pumps to operate on Bi-fuel/dual-fuel (for max. 20 cylinders engines)

IBF-CU-R IB-Lite IB-NT I-CB IC-NT IC-NT CT-BIO7 I-CR ID IDC ID-BF ID-CCU ID-COM ID-DCU ID-DFM ID-EM ID-FLX-Lite ID-FLX-FPC

Bi-Fuel Railway firmware for ID-Mobile Communication plug-in module with Ethernet 10/100 Mbit interface in RJ45 connector for IL-NT, IA-NT, IC-NT and ID-Lite controllers Communication Module with Cellular/Ethernet Connection for IC-NT, IG/IS-NT and ID controllers Communication Bridge - interfaces IS, IG/IS-NT, ID controllers and nonstandard engine ECU InteliCompact New Technology gen-set controller Hybrid plug-in extension module with 1 current input and 7 binary inputs/outputs CAN Repeater module - Intercontroller CAN bus extension module InteliDrive controller Import package for DriveConfig InteliDrive controller for Bi-Fuel applications InteliDrive Compressor Control Unit Communication module for multiple engine installations, remote displays and redundancy communication for ID controllers InteliDrive engine control unit DualFuelModule for ID-BF controller InteliDrive Lite Electric Motor controller InteliDrive Lite engine controler InteliDrive Lite Fire Pump Controler

ID-FLX-DC ID-FLX-IPC ID-Lite ID-Mobile ID-Mobile Logger

InteliDrive Lite Direct Current controler InteliDrive Lite Irigation Pump Controller Former version ID-Lite engine controller Engine controller with IP67 protection Engine data logger

IDMT

Inverse Definite Minimum Time - protection which trips the sooner the higher value is measured (e.g. current, load), the dependence is hyperbolic

ID-Nano ID-Nano-CC ID-RPU ID-SCM

Small engine controller Small Compressor Controller Redundant Protection Unit for ID-DCU-Marine controller Speed Control Module for InteliDrive controllers

ID-SCM1

Speed Control Module for InteliDrive controllers (cost effective version)

IG-AVRi IG-AVRi TRANS/LV IGC

IG Automatic Voltage Regulator interface Low voltage transformer for IG Automatic Voltage Regulator interface IG/IS-NT firmware upgrade package InteliGen for Electronic Engines (HW optimized for connection to an engine equipped with ECU)

IG-EE IG-EEC IG-IB IG-IOM IGL-RA15 IG-MTU IG-NT IG-NT-BB IG-NTC IG-NTC-BB IGS-NT-LSM+PMS IGS-PTM ICHG I-LB+ I-LBA IL-NT IL-NT GPRS IL-NT RS232

InteliGen EE controller with extended communication possibilities + switchable sensing ranges of AC voltages and currents IG-Internet Bridge - for internet/ethernet communication Extension module with 8 BI/BO, 4 AI and 1 AO for IL-NT, IC-NT and InteliPro controllers Indication panel with LEDs signalizing state of 15 BO Mains Transformer Unit InteliGen New Technology gen-set controller InteliGen New Technology BaseBox gen-set controller InteliGen New Technology controller with extended communication possibilities + switchable sensing ranges of AC voltages and currents InteliGen New Technology BaseBox controller with extended communication possibilities + switchable sensing ranges of AC voltages and currents Dongle for IG-XX and IS-NT to enable Load Sharing and VAr sharing control loops and PMS Extension module with 8 BI/BO, 4 AI and 1 AO InteliCharger - automatic battery charger Local Bridge – communication module for direct and modem monitoring and control of multiple gen-sets Low Battery Adaptor InteliLite New Technology gen-set controller Communication plug-in module with GSM/GPRS modem for IL-NT, IC-NT and ID-Lite controllers Communication plug-in module with RS232 port for IL-NT, IA-NT, IC-NT and ID-Lite controllers

IL-NT RS232-485

Communication plug-in module with RS232 and RS485 ports for IL-NT, IANT, IC-NT and ID-Lite controllers

IL-NT S-USB

Service communication plug-in module with USB slave port for IL-NT, IANT, IC-NT and ID-Lite controllers

IL-NT-AIO

Extension plug-in module with 4 analog inputs and 1 analog output for ID-FLX-Lite family controllers

IL-NT-AOUT8

Extension plug-in module with 8 PWM open collector type outputs for ILNT, IA-NT, IC-NT and ID-Lite controllers

IL-NT-BIO8

Extension plug-in module with 8 binary inputs/outputs for IL-NT, IA-NT, IC-NT and ID-Lite controllers

IL-NT-IO1

Extension plug-in module with 4 analog outputs and 4 binary inputs for ID-FLX-Lite family controllers

IM-NT

InteliMains New Technology - Mains supervision controller; the same controller with a different SW configuration can work as a bus-tie synchronizer

IM-NT-BB IM-NTC-BB IN-NT IP I-RB I-RB IS-AIN8 IS-AIN8TC IS-BIN8/16 IS-NT IS-NT-BB IS-NTC-BB IV17T IV5 IV5 CAN IV5 CAN BL IV5 RD IV8 KWP2000 LAI LBI LDE LDS

InteliMains New Technology BaseBox - Mains supervision controller InteliMains New Technology BaseBox - Mains supervision controller with extended communication options InteliNano New Technology gen-set controller Internet Protocol Relay Board Relay Board Extension module with 8 AI Extension module with 8 AI for thermocouple measurements Extension module with 8 BO and 16 BI. InteliSys New technology gen-set controller InteliSys New Technology Basic Box (without display) - classic line InteliSys New Technology Basic Box (without display) - new line InteliVision 17Touch - 17" color display for IG/IS-NT and ID controllers InteliVision 5 - 5,7" color display for IG/IS-NT controllers InteliVision 5 - 5,7" color display for ID controllers InteliVision 5 - 5,7" color display for ID controllers with backlit buttons InteliVision 5 Remote Display - 5,7" color display for IG/IS-NT controllers for remote connection up to 1km InteliVision 8 - 8" color display for IG/IS-NT and ID controllers Key Word Protocol of Scania S6 unit (for engine diagnostics) Logical Analog Inputs (card in GenConfig which is used to assign source signal to controller Logical Analog Input functions, e.g. Oil press) Logical Binary Inputs (card in GenConfig which is used to assign source signal to controller Logical Binary Input functions, e.g. Sys Start/Stop) Line Diagram Editor - SCADA editor in InteliMonitor Load Demand Swap - automatic start and stop of different sized gen-sets within a group based on actual load and belonging to predefined power bands

LdShed LChr

Load shedding - disconnecting of unessential load after Mains fail to enable start of needed number of gen-set Load Character - IG/IS-NT history column name

LoP

Low Power - protection type, causes reduction of the required gen-set load to the Min Power PtM during parallel-to-mains operation or local baseload operation

LS / LdSharing

Load Sharing - analog load sharing line to interconnect gen-sets on site (for island parallel or mains parallel operation of multiple gen-sets); IG/IS/IM-NT controllers use digital Load Sharing via the CAN2 bus

LSM LT MCB MC-NT MGCB MINT MP MRS MultIslOp MultParOp MVS NCB NPU OC OfL Peak shaving PF PGN PLC

PMS

PSC PT PWM Reverse synchronisation

Load Sharing Module Option for Low Temperature modification (display equipped with heating foil) Mains Circuit Breaker Mains Compact New Technology controller Master Generator Circuit Breaker (sometimes used with multiple gen-sets in island parallel or mains parallel operation) Multiple application with INTernal control loops - for multiple gen-sets in island parallel or mains parallel operation; Load Sharing and VAr Sharing controlled internally; PMS available Mains Protection Manual and Remote Start Multiple Island Operation (MCB is opened, GCB’s are closed) Multiple Parallel Operation (MCB is closed, GCB’s are closed) Mains Vector Shift - IG/IS-NT history column name Neutral Circuit Breaker Mains protection relay (voltage, frequency, vector shift protections) Occurrence Count (number of fault occurrances transmitted in diagnostic frame from ECU) Off load - protection type (see application manual for details) Supply of part of the load by gen-sets while import from the Mains is higher than preadjusted limit, prevents excess of Mains import limit during periods with high consumption Power Factor Parameter Group Number (refer to SAE J1939-71) Programmable Logic Controller - PLC functions available in IG/IS-NT and ID controllers Power Management System - ensures optimization of running gen-sets on sites with multiple gen-sets; based on kW/kVA spinning reserve or on relative (%) load; no-master system ensures high reliability Power Station Controller - SW branch for IG/IS-NT controllers dedicated to control and monitoring of power stations Potential Transformer Pulse-Width Modulation Synchronisation of loaded genset to mains (MCB closing process)

ROCOF RTC SCADA SD SG SHAIN SHAOUT SHBIN SHBOUT SLD SMTP SNMP Soft load Soft unload

Rate of Change of Frequency - Mains protection Real Time Clock Supervisory Control and Data Acquisition systém Shutdown - protection type (see InteliGen/InteliSys Reference Guide for details) Speed Governor Shared (virtual) Analog INput module Shared (virtual) Analog OUTput module SHared (virtual) Binary INput module SHared (virtual) Binary OUTput module Single Line Diagram - SCADA drawing created in InteliMonitor Simple Mail Transfer Protocol - an Internet standard for electronic mail (e-mail) transmission across Internet Protocol (IP) networks Simple Network Management Protocol - an "Internet-standard protocol for managing devices on IP networks" Generator soft loading according to Load ramp loop setting Generator soft unloading according to Load ramp loop setting

SPI

Single Parallel Island application - for single gen-sets in parallel with mains or in island operation; suitable for CHP applications; no MCB control

SPM SPN

Single Prime Mover application - for single gen-sets without mains Suspect Parameter Number (refer to SAE J1939-71)

SPtM

Single Parallel to Mains application - for single gen-sets in parallel with mains or in island operation, with AMF support; both MCB and GCB controlled

SRO SS SSB STP VBOUT VPIO VRO VS VT WRN WSUP ZST

Speed Regulation Output Single Speed application in ID-DCU and ID-Mobile controllers Single Stand-By application - for single gen-sets with mains and break transfer to mains Slow stop - protection type Virtual Binary Outputs (ID-DCU, ID-Mobile) Virtual periphery I/O module – internal “SW wires” linking binary outputs to inputs Voltage Regulation Output VAr Sharing - ensures VAr sharing between gen-sets on site via the CAN2 bus (for island parallel or mains parallel operation of multiple gen-sets) Voltage Transformer Warning WebSupervisor - cloud based system for monitoring and controlling of ComAp controllers through web Zipped Archive Set - file created by InteliMonitor, can be used for sending of complete archive sets to the ComAp technical support