Konfigurasi OSPF pada Cisco Packet Tracer Pertama kita buat dulu sebuah jaringan , seperti gambar dibawah.....

Selanjutnya.. berikan IP Address pada setiap PC.. 1. PC 1 dengan nama "PC0"..

2. PC 2 dengan nama "PC 2"..

PC 3 dengan nama "PC 3"..

Tahap selanjutnya berikan IP Address pada setiap router . Contoh sebagai berikut :

Pemberian IP Address di Router 1 --- System Configuration Dialog --Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#int fa0/0 Router(config-if)#ip add 172.18.8.1 255.255.0.0 Router(config-if)#no shut Router(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up Router(config-if)#exit Router(config)#int se2/0 Router(config-if)#ip add 192.168.8.1 255.255.255.0 Router(config-if)#band 125 Router(config-if)#cl ra 125000 Router(config-if)#no shut %LINK-5-CHANGED: Interface Serial2/0, changed state to down Router(config-if)#exit

Konfigurasi EIGRP pada Router 1, Router(config)#router ospf 4 Router(config)#router-id 2.2.2.2 Router(config-router)#net 172.18.8.0 0.0.255.255 area 0 Router(config-router)#net 192.168.8.0 0.0.0.255 area 0 Router(config-router)#log-adjacency Router(config-router)#end Router# %SYS-5-CONFIG_I: Configured from console by console wr Building configuration... [OK] Router#

Pemberian IP Address di Router 2 --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#int fa0/0 Router(config-if)#ip add 172.19.9.1 255.255.0.0 Router(config-if)#no shut Router(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up Router(config-if)#exit Router(config)#int se2/0 Router(config-if)#ip add 192.168.8.2 255.255.255.0 Router(config-if)#band 125 Router(config-if)#no shut %LINK-5-CHANGED: Interface Serial2/0, changed state to down Router(config-if)#exit Router(config-if)#exit Router(config)#int se3/0 Router(config-if)#ip add 18.8.8.1 255.0.0.0 Router(config-if)#band 125 Router(config-if)#cl ra 125000 Router(config-if)#no shut %LINK-5-CHANGED: Interface Serial3/0, changed state to down Router(config-if)#exit

Konfigurasi OSPF pada Router 2, Router(config)#router ospf 4 Router(config-router)#net 172.19.9.1 0.0.255.255 area 0 Router(config-router)#net 192.168.8.0 0.0.0.255 area 0 Router(config-router)#net 18.8.8.0 0.255.255.255 area 1 Router(config-router)#log-adjacency Router(config-router)#end Router# %SYS-5-CONFIG_I: Configured from console by console wr Building configuration... [OK] Router#

Pemberian IP Address di Router 3 --- System Configuration Dialog --Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#int fa0/0 Router(config-if)#ip add 172.16.10.1 255.255.0.0 Router(config-if)#no shut Router(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up Router(config-if)#exit Router(config)#int se2/0 Router(config-if)#ip add 18.8.8.2 255.0.0.0 Router(config-if)#band 125 Router(config-if)#no shut %LINK-5-CHANGED: Interface Serial2/0, changed state to down Router(config-if)#exit

Konfigurasi OSPF pada Router 3, Router(config)#router ospf 4 Router(config)#router-id 4.4.4.4 Router(config-router)#net 172.16.10.0 0.0.255.255 area 1 Router(config-router)#net 18.8.8.0 0.255.255.255 area 1 Router(config-router)#log-adjacency Router(config-router)#end Router# %SYS-5-CONFIG_I: Configured from console by console wr Building configuration... [OK] Router#

Konfigurasi EIGRP pada Cisco Packet Tracer Pertama kita buat sebuah jaringan sederhana...

Pemberian IP Address pada masing-masing PC yang terhubung.. - Pemberian IP pada PC '1'...

- Pemberian IP pada PC '2'...

- Pemberian IP pada PC '3'...

- ROUTER ke-1 'Router A' --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#int fa0/0 Router(config-if)#ip add 192.168.1.1 255.255.255.0 Router(config-if)#no shut Router(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up Router(config-if)#exit Router(config)#int se2/0 Router(config-if)#ip add 10.10.4.1 255.0.0.0 Router(config-if)#band 64 Router(config-if)#cl ra 64000 Router(config-if)#no shut %LINK-5-CHANGED: Interface Serial2/0, changed state to down Router(config-if)#exit Konfigurasi RIP pada 'Router A'..

Router(config)#router eigrp 2 Router(config-router)#net 192.168.1.1 Router(config-router)#net 10.10.4.1 Router(config-router)#exit Router# %SYS-5-CONFIG_I: Configured from console by console wr Building configuration... [OK] Router#

- ROUTER ke-2 'Router B'

--- System Configuration Dialog --Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#int fa0/0 Router(config-if)#ip add 192.168.2.1 255.255.255.0 Router(config-if)#no shut Router(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up Router(config-if)#exit Router(config)#int se2/0 Router(config-if)#ip add 10.10.4.2 255.0.0.0 Router(config-if)#band 64 Router(config-if)#no shut %LINK-5-CHANGED: Interface Serial2/0, changed state to down Router(config-if)#exit Router(config-if)#exit Router(config)#int se3/0 Router(config-if)#ip add 172.16.2.1 255.255.0.0 Router(config-if)#band 64 Router(config-if)#cl ra 64000 Router(config-if)#no shut %LINK-5-CHANGED: Interface Serial3/0, changed state to down Router(config-if)#exit Konfigurasi RIP pada 'Router B' ..

Router(config)#router eigrp 2 Router(config-router)#net 192.168.2.1 Router(config-router)#net 10.10.4.2

Router(config-router)#net 172.16.2.1 Router(config-router)#exit Router# %SYS-5-CONFIG_I: Configured from console by console wr Building configuration... [OK] Router#

- ROUTER ke-2 'Router C' --- System Configuration Dialog --Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#int fa0/0 Router(config-if)#ip add 192.168.4.1 255.255.255.0 Router(config-if)#no shut Router(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up Router(config-if)#exit Router(config)#int se2/0 Router(config-if)#ip add 172.16.2.2 255.255.0.0 Router(config-if)#band 64 Router(config-if)#no shut %LINK-5-CHANGED: Interface Serial2/0, changed state to down Router(config-if)#exit

Konfigurasi RIP pada 'Router C' ..

Router(config)#router eigrp 2 Router(config-router)#net 192.168.4.1 Router(config-router)#net 172.16.2.2 Router(config-router)#exit Router# %SYS-5-CONFIG_I: Configured from console by console wr Building configuration... [OK] Router#

Setelah dikonfigurasi, coba di ping dari PC Atas, Tengah dan Bawah