ECMA-352 3rd Edition / June 2013

Near Field Communication Interface and Protocol -2 (NFCIP-2)

Reference number ECMA-123:2009

© Ecma International 2009

COPYRIGHT PROTECTED DOCUMENT

© Ecma International 2013

Contents

Page

1 

Scope ...................................................................................................................................................... 1 

2 

Conformance ......................................................................................................................................... 1 

3 

Normative references ............................................................................................................................ 1 

4 

Terms and definitions ........................................................................................................................... 1 

5  5.1 

Conventions and notations .................................................................................................................. 2  Names ..................................................................................................................................................... 2 

6 

External RF field detection ................................................................................................................... 2 

7 

Mode selection and switching ............................................................................................................. 2 

8 

External RF field detection and initial RF generation ........................................................................ 4 

© Ecma International 2013

i

Introduction In 2002, Ecma International formed Task Group 19 of Technical Committee 32 to specify Near Field Communication (NFC) signal interfaces and protocols. The NFC devices are wireless closely coupled devices communicating at 13,56 MHz. Although ECMA-340, ISO/IEC 14443 and ISO/IEC 15693 standards all specify 13,56 MHz as their working frequency, they specify distinct communication modes. These are defined as NFC, PCD and VCD communication modes respectively. This NFCIP-2 Standard specifies the mechanism to detect and select one communication mode out of those three possible communication modes. Furthermore, NFCIP-2 requires that subsequent behaviour be as specified in the standard specifying the selected communication mode. The 2 nd edition adds support for the PICC mode from ISO/IEC 14443. In 2009, JTC 1/SC 6 and JTC 1/SC 17 studied together for improving interoperability between ISO/IEC 21481 and ISO/IEC 14443. This second edition of ISO/IEC 21481 is revised based on the study, and the PICC mode is added to the existing three modes. This 3rd edition is aligned with ISO/IEC 21481:2012.

This Ecma Standard has been adopted by the General Assembly of June 2013.

ii

© Ecma International 2013

"COPYRIGHT NOTICE © 2013 Ecma International This document may be copied, published and distributed to others, and certain derivative works of it may be prepared, copied, published, and distributed, in whole or in part, provided that the above copyright notice and this Copyright License and Disclaimer are included on all such copies and derivative works. The only derivative works that are permissible under this Copyright License and Disclaimer are: (i)

works which incorporate all or portion of this document for the purpose of providing commentary or explanation (such as an annotated version of the document),

(ii) works which incorporate all or portion of this document for the purpose of incorporating features that provide accessibility, (iii) translations of this document into languages other than English and into different formats and (iv) works by making use of this specification in standard conformant products by implementing (e.g. by copy and paste wholly or partly) the functionality therein. However, the content of this document itself may not be modified in any way, including by removing the copyright notice or references to Ecma International, except as required to translate it into languages other than English or into a different format. The official version of an Ecma International document is the English language version on the Ecma International website. In the event of discrepancies between a translated version and the official version, the official version shall govern. The limited permissions granted above are perpetual and will not be revoked by Ecma International or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and ECMA INTERNATIONAL DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY OWNERSHIP RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE."

© Ecma International 2013

iii

iv

© Ecma International 2013

Near Field Communication Interface and Protocol -2 (NFCIP-2)

1

Scope

ECMA-340, ISO/IEC 14443 and ISO/IEC 15693 specify the radio frequency signal interface, initialization, anticollision and protocols for wireless interconnection of closely coupled devices and access to contactless integrated circuit cards operating at 13,56 MHz. This Standard specifies the communication mode selection mechanism, designed not to disturb any ongoing communication at 13,56 MHz, for devices implementing ECMA-340, ISO/IEC 14443 or ISO/IEC 15693. This Standard requires implementations to enter the selected communication mode as specified in the respective Standard. The communication mode specifications, however, are outside the scope of this Standard.

2

Conformance

Conforming devices implement mode selection specified in Clause 7 and implement the NFC MODE, PCD MODE, VCD MODE, and PICC MODE.

3

Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ECMA-340, Near Field Communication — Interface and Protocol (NFCIP-1) ISO/IEC 14443-2:2010, Identification cards — Contactless integrated circuit cards — Proximity cards — Part 2: Radio frequency power and signal interface ISO/IEC 14443-3:2011, Identification cards — Contactless integrated circuits cards — Proximity cards — Part 3: Initialization and anticollision ISO/IEC 14443-4:2008, Identification cards — Contactless integrated circuit cards — Proximity cards — Part 4: Transmission protocol ISO/IEC 15693-2:2006, Identification cards — Contactless integrated circuit cards — Vicinity cards — Part 2: Air interface and initialization ISO/IEC 15693-3:2009, Identification cards — Contactless integrated circuit cards — Vicinity cards —Part 3: Anticollision and transmission protocol

4

Terms and definitions

For the purposes of this document, the following terms and definitions apply. 4.1 HTHRESHOLD minimum value of an external RF field

© Ecma International 2013

1

NOTE

Adapted from ECMA-340, 4.6.

4.2 NFCIP-2 device ISO/IEC 21841 entity 4.3 NFC MODE mode in which an NFCIP-2 device operates as specified in ECMA-340 4.4 fc frequency of operating field (carrier frequency) as specified in ISO/IEC 14443-2 4.5 PICC MODE mode in which an NFCIP-2 device operates as a Type A or Type B Proximity Integrated Circuit Card or Object as specified in ISO/IEC 14443-2, ISO/IEC 14443-3 and ISO/IEC 14443-4 4.6 PCD MODE mode in which an NFCIP-2 device operates as a Proximity Coupling Device as specified in ISO/IEC 14443-2, ISO/IEC 14443-3 and ISO/IEC 14443-4 4.7 VCD MODE mode in which an NFCIP-2 device operates as a Vicinity Coupling Device as specified in ISO/IEC 15693-2 and ISO/IEC 15693-3

5 5.1

Conventions and notations Names

The names of basic elements, e.g. specific fields, are written with a capital initial letter.

6

External RF field detection

During external RF field detection, NFCIP-2 devices shall, for a period of TIDT + n × TRFW (see 11.1.1 of ECMA340), detect external RF fields at fc with a value higher than HTHRESHOLD and shall not switch on their own RF field.

7

Mode selection and switching

Mode switching specifies the procedure for NFCIP-2 devices to enter the NFC PICC MODE or VCD MODE selected prior to the following sequence.

MODE,

or the PCD

MODE

or

NFCIP-2 devices shall execute the following sequence: 1. The NFCIP-2 device shall have its RF field switched off. 2. If the PICC MODE has been selected, the NFCIP-2 device shall enter the PICC MODE. 3. If the NFCIP-2 device detects an external RF field, as specified in Clause 6, it shall enter the NFC MODE as a Target.

2

© Ecma International 2013

4. If the NFCIP-2 device does not detect an external RF field and the NFC enter the NFC MODE as an Initiator.

MODE

has been selected, it shall

5. If the NFCIP-2 device does not detect an external RF field and the PCD MODE or the VCD MODE has been selected, it shall perform external RF field detection and Initial RF generation as specified in Clause 8. Figure 1 illustrates the above procedure. Start

NFCIP-2 device shall have its RF field switched off

PICC MODE Selected ?

External RF field detected

no

External RF field detected ? yes

External RF field detected

yes no

NFC MODE, PCD MODE or VCD MODE selected?

VCD MODE

PCD MODE NFC External RF field detected or Timeout?

MODE

RF waiting time expired

PICC MODE

PCD MODE

NFC MODE

External RF field detected or Timeout? RF waiting time expired

VCD MODE

END

Figure 1 — Mode selection

© Ecma International 2013

3

8

External RF field detection and initial RF generation

When the NFCIP-2 device detects an external RF field, as specified in Clause 6, during the time TIDT + n × TRFW it shall recommence the procedure specified in Clause 7. If the NFCIP-2 device does not detect an external RF field during the time TIDT + n × TRFW, it shall switch on its RF field, and enter the selected communication mode while observing TIRFG. See 11.1.1 of ECMA-340 for TIDT, TRFW and n. TIRFG is the initial guard-time between switching on RF field and starting modulation to send command or data. 5.1 of ISO/IEC 14443-3:2011 and 7.3 of ISO/IEC 15693-2:2006 specify TIRFG for PCD MODE and VCD MODE, respectively. Figure 2 illustrates the external RF field detection and initial RF generation.

Data or Command

RF On TRFW

Start

TIDT

n * TRFW

TIRFG

Figure 2 — RF detection and initial RF generation for PCD MODE and VCD MODE

4

© Ecma International 2013

© Ecma International 2013