PORTABLE DISHWASHER
vens, Compactors,
Room Air Conditioners,
Dehumldlflers,
Automatic
Washers, Clothes Dryers, Freezers, Refrigerator-Freezers,
Ice Makers,Dish\
INSTALLATION PROCEDURE Before You Begin.. a
I. (‘aster Installation and Removal of’ Materials From Interior Gstf;:s are supplied the c!lsllwasher tub.
rn tile
loose
parts
bag inside
Lay tile dishwasher on its back using 2 corner posts to prevent paint scratching. The corner posts should be [)laced as shown in Figure 1
2. Faucet Adapter Kit Installation Remove screen holder or aerator if one is present. (See Figure 3.)
Remove Insert Figure
tile bottom casters 2.
into
pad mo:lntlng
holes
as shown
Stand the dishwasher upright and then remove I,acking rndterials, Customer Literature Package, faucet ;jcl;ll)ter kit from the dishwasher.
in
the and
After ,llst,tllation has been coml)leted, discard the ~Jxkrnq rliaterlals. Piace tile Customer Literature P,jckage and this InstallatYon Ir!struction on the top of the dishwasher so th;lt they are readily available to the customer.
from
faucet
spout
Electrical
ground
is required
on this appliance.
If ‘yo111. f;iiicet spout has vxxternal threads, screw the Adapter tst:;ll the adapter onto the tbushing as shown ~II F I qu r&i ii
RUBBER WASHER AND THREADED BUSHING (FOR FAUCETS WITH INTERNAL THREADS)
Keconmended
Grounding
Method
DO NOT, UNDER ANY CIRCUMSTANCES,REMOVE THE POWER SUPPLY CORD GROUND PRONG.
For other type faucets, type adapter kits.
see your
dealer
for special
NOTE: If dishwasher is attached to a faucet equipped with a spray hose attachment, walc’r pressure is applied to the spray hose. To prevent possible failure, the spray hose should be permanently disconnected or rep placed with a good quality reinforced hose.
For your personal safety, this appliance must be grounded. This appliance is equipped with a power supply cord having a 3-prong grounding plug. To minimize possible shock hazard it must be plugged into a mating 3-prong grounding type wall receptacle, grounded in accordance with the National Electrical Code and tocat codes and ordinances. If a mating wall receptacle is not available, it is the personal responsibility and obligation of the customer to have a properly grounding 3-prong watt receptacle installed by a qualified electrician. See Figure 6.
m
~-~~%:ING TYPE WALL RECEPTACLE
3-PRONG GROUNDING
3. Electrical Requirements A 120
Volt,
60 Hz, AC only, 15 Amp (20 Amp fused electrical supply is required. (TII-ne rielay fuse is recommended.) It is recom nlentle[l tt:,rt a separate circuit serving only this apl)l~;~nce !~e provIdeO. DO NOT LISC an extension coral Se[> Figure 5. 171ilxir1ldl~~~
POWER CORD
SUPPLY
~_--~- -__ PUSH COLLAR AND SLIP FAUCET CONNECTOR ONTO THE FAUCET ADAPTER
-1. Fmcet Conntdion NOTE: Mininlurn ‘~.lax~rnurrl water r:: :dircjl?ierits are 15 PSI to 120 PSI.
pressure
-4
BUTTON 0 T.lrn
water
off.
c. Use tiie ring til 111111hoses out of cornpariment 011 /lack of dishwasher.
storage
Operational Test
(;. AtLach
the ties? connector to the faucet by pulling down on the locking collar and lift tny up on the connector until it snaps into place on the faucet adapter. Release the locking collar. See Figure 7.
e. Turn the hot position
water on slowly
to the full open
l
Spin spray
0
Start
0
Check for leaks - particularly around door, pump mounting gasket, and at hose connections.
0
Check round
water level -- water heater element. .
just cover
the
0
Check visible
for complete drain - no water should above grate when drain is complete.
be
arm to check
movement.
Dishwasher.
should
If Dishwasher Won’t Run, or Stops During Cycle.. . Before Calling for Service, Check These Points:
After
the dishes
are washed:
a, Turn hot water OFF. during the dry cycle.) b. Press the red button release water pressure. c. Grasp
hose
connector
d. Move the locking on the connector. c. Empty nector
any
collar
rem,jlning
f. Push hoses into storage
(This
may
be done
on the connector See Figure 8. and down water
lift
to
1.
Is door
2.
Has cycle
tightly
closed
3.
Is water turned
on?
4.
Is electric
plugged
been correctly cord
and
latched
In?
5.
Has house fuse blown?
6.
Has electrical
7.
If motor has stopped because it will automatically reset itself
power
securely?
set to start dishwasher?
been interrupted? of overload, within a few
minutes.
up slightly.
and pull down from
the
con-
NOTE: To convert a front loading portable dishwasher Into a built-in model, contact your Whirlpool appliance dealer. Conversion Kit No. 569056 is available through hirr to facilitate the installation.
cotnpartment.
4
Instructions for Changing Color in Front Panel Pack For Models SO Equipped
Remove Side Trim NOTE: change
Either side trrn color in the Front
may be removed Panel Pack.
to
STEEP 1. Remove the tb’:o screlvs that fasten side trlrn to the door frarrle. See Figure 9. STEEP 2. Open the door