Industrial Technology

2016 HIGHER SCHOOL CERTIFICATE EXAMINATION Industrial Technology Timber Products and Furniture Technologies Total marks – 40 Section I General Inst...
35 downloads 2 Views 145KB Size
2016

HIGHER SCHOOL CERTIFICATE EXAMINATION

Industrial Technology Timber Products and Furniture Technologies

Total marks – 40 Section I General Instructions • Reading time – 5 minutes • Working time – 1 12 hours • Write using black pen • Draw diagrams using pencil • Board-approved calculators may be used • Write your Centre Number and Student Number at the top of page 5

Pages 2–4

10 marks • Attempt Questions 1–10 • Allow about 20 minutes for this section Section II

Pages 5–7

15 marks • Attempt Questions 11–15 • Allow about 35 minutes for this section Section III

Page 9

15 marks • Attempt Question 16 • Allow about 35 minutes for this section

2410

Section I 10 marks Attempt Questions 1–10 Allow about 20 minutes for this section Use the multiple-choice answer sheet for Questions 1–10. 1

What type of screw is shown?

(A) Coach (B)

Raised head

(C)

Round head

(D) Countersunk head

2

What term is used for the edge treatment shown?

(A) Bevel (B)

Chamfer

(C)

Rebate

(D) Splay

3

How are burls formed? (A) Abnormal growth (B)

Damage during felling

(C)

Poor conversion process

(D) Deformation of the pith

–2–

4

What method of timber conversion is shown?

(A) Live sawing (B)

Back sawing

(C)

Quarter sawing

(D) Through sawing

5

Which tool would be the most appropriate to produce a smooth surface on an internal curve? (A) Rasp (B)

Chisel

(C)

Scraper

(D) Smoothing plane

6

Why should furniture be dry assembled before final assembly? (A) To remove excess glue (B)

To remove excess moisture

(C)

To check if the joints fit properly

(D) To remove stresses from all directions

–3–

7

Which of the following applies to formaldehyde adhesive? (A) Adheres on contact (B)

Dries to a clear finish

(C)

Can be softened by heat once set

(D) Setting action is caused by chemical change

8

9

Which of the following images shows a tongue and groove joint? (A)

(B)

(C)

(D)

What term is used to describe the application of pieces of veneer to a surface to form decorative patterns, designs or pictures? (A) Decoupage (B)

Marquetry

(C)

Parquetry

(D) Pyrography

10

A project requires ten boards, each 250 mm wide, 100 mm thick and 5.3 metres long. How much would the project cost if timber is $100 per cubic metre? (A) $13.25 (B)

$132.50

(C)

$660.25

(D) $6600.25

–4– © 2016 Board of Studies, Teaching and Educational Standards NSW

2016 HIGHER SCHOOL CERTIFICATE EXAMINATION

Industrial Technology Centre Number

Timber Products and Furniture Technologies

Student Number

Section II 15 marks Attempt Questions 11–15 Allow about 35 minutes for this section

Answer the questions in the spaces provided. These spaces provide guidance for the expected length of response. Show all relevant working in questions involving calculations. Question 11 (1 mark)

What is the purpose of the symbol shown on the timber? ....................................................................................................................................................... .......................................................................................................................................................

2411

–5–

Question 12 (3 marks) Describe a process that can be used for making a widening joint using a portable power tool. ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... .......................................................................................................................................................

Question 13 (3 marks) Compare the use of oil-based and water-based finishes on timber. ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... .......................................................................................................................................................

–6–

Question 14 (3 marks) Describe the process needed to restore the edge of the chisel shown.

....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... .......................................................................................................................................................

Question 15 (5 marks) Explain the advantages of using manufactured boards rather than solid timber in constructing a top for a dining table. ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... ....................................................................................................................................................... .......................................................................................................................................................

–7–

BLANK PAGE

–8– © 2016 Board of Studies, Teaching and Educational Standards NSW

2016 HIGHER SCHOOL CERTIFICATE EXAMINATION

Industrial Technology Timber Products and Furniture Technologies Section III 15 marks Attempt Question 16 Allow about 35 minutes for this section Answer part (a) of the question in a writing booklet. Answer part (b) of the question in a SEPARATE writing booklet. Extra writing booklets are available. Question 16 (15 marks) Answer part (a) of the question in a writing booklet. (a)

Using an example, outline the purpose of risk assessment within the timber products and furniture industry.

5

Answer part (b) of the question in a SEPARATE writing booklet. (b)

Explain how particular historical developments have influenced the timber products and furniture industry.

End of paper

2412

–9–

10

BLANK PAGE

– 10 – © 2016 Board of Studies, Teaching and Educational Standards NSW