Inch Series Push-In Fittings Dimensions in Inches (mm)
Pneufit Male Connector A Tube O.D.
S
ØA 10-32 UNF
ØC
L
B NPT or UNF Thread
Part Number
C A/F 0.35 (9)
10-32 UNF
12 425 0110
1/16
12 425 0116
3/8"
1/8
12 425 0118
7/16"
1/4
12 425 0128
9/16"
10-32 UNF
12 425 0210
0.35 (9)
1/8
12 425 0218
7/16"
1/4
12 425 0228
9/16"
1/8
12 425 0318
7/16"
1/4
12 425 0328
9/16"
10-32 UNF
12 425 0410
0.43 (11.0)
1/8
12 425 0418
7/16"
1/4
12 425 0428
9/16"
3/8
12 425 0438
11/16"
1/8
12 425 0518
1/2"
1/4
12 425 0528
9/16"
3/8
12 425 0538
11/16"
1/8
12 425 0618
11/16"
1/4
12 425 0628
11/16"
3/8
12 425 0638
11/16"
1/2
12 425 0648
7/8"
1/4
12 425 0728
7/8"
3/8
12 425 0738
7/8"
1/2
12 425 0748
7/8"
B
1/8"
L G
ØA
S C
5/32"
B
All straight male connectors have an internal hex for the use of an Allen Wrench to allow the fitting to be mounted in any position. This also permits close porting not possible with a standard open end or socket wrench.
Inch Series Push-In Fittings Dimensions in Inches (mm)
Pneufit Male Connector - Conversion (MM O.D. Tube to NPTF [Male] Thread)
A Tube O.D.
L G
ØA
4
S C
B
All straight male connectors have an internal hex for the use of an Allen Wrench to allow the fitting to be mounted in any position. This also permits close porting not possible with a standard or open end socket wrench.
B NPT Thread
Part Number
10-32
12 425 0210
1/8
12 425 0218
1/4
12 425 0228
1/8
10 425 0518
1/4
10 425 0528
10-32
10 425 0610
1/8
10 425 0618
1/4
10 425 0628
3/8
10 425 0638
5
6
1/8
NOTE: For 4 mm tube use 5/32" fittings and for 8 mm tube use 5/16" fittings
Inch Series Push-In Fittings Dimensions in Inches (mm)
Pnuefit Male Connector - Conversion (Inch O.D. Tube to ISO R [Male] Thread)
A Tube O.D.
L G
ØA
B ISO R Thread
Part Number
1/8
12 125 0118
1/4
12 125 0128
1/8
10 125 0418
1/4
10 125 0428
1/8
12 125 0418
1/4
12 125 0428
3/8
12 125 0438
1/8
10 125 0818
1/4
10 125 0828
3/8
10 125 0838
1/8
12 125 0618
1/4
12 125 0628
3/8
12 125 0638
1/2
12 125 0648
1/4
12 125 0728
3/8
12 125 0738
1/2
12 125 0748
1/8"
S C
B
All straight male connectors have an internal hex for the use of an Allen Wrench to allow the fitting to be mounted in any position. This also permits close porting not possible with a standard or open end socket wrench.
5/32"
1/4"
5/16"
3/8"
1/2"
Pneufit Self Sealing (Checked) Connector (Inch tube to NPT) C A
Operation: Insertion of a tube into the push-in end ("A") of the fitting compresses a spring, and unseats the plunger and seal assembly. In this state (tube inserted), flow is allowed through the fitting. Removal of the tubing from the fitting allows the spring to extend, seating the plunger seal. When pressure is applied to the system, the plunger assembly seals off the push-in end of the fitting, allowing the system to remain pressurized. Note: Remember to depressurize the system before inserting or removing tubing from this or any other Pneufit. Littleton, CO USA
Phone 303-794-2611
www.norgren.com
FIT-1-17
Inch Series Push-In Fittings Dimensions in Inches (mm)
Straight stem adapters allow use of Standard Inch (12-Series) and Standard Metric (10-Series) Pneufit Push-in tube unions to create nearly any configuration of Swivel Adapter tube fitting. Various combinations of these products in conjunction with the conversion fitting straight stem adapters are shown at right, creating an entire spectrum of inch O.D. tube to ISO R and MM O.D. tube to NPTF (male) swivel male elbows, swivel male branch and run tees.
Pneufit Stem Adapter L
MM or IN. O.D. Tube
or
Inch O.D Tube
Swivel Male Elbows
B
+
=
or
Swivel Male Branch & Run Tees ISO R Thread
A Tube O.D.
G ØA
MM O.D Tube
B NPT Thread
or
NPT Thread
C A/F
Part Number
10-32 UNF
12 415 0210
5/16"
1/8
12 415 0218
7/16"
1/4
12 415 0228
9/16"
1/8
12 415 0418
7/16"
1/4
12 415 0428
9/16"
1/8
12 415 0518
7/16"
1/4
12 415 0528
9/16"
1/4
12 415 0628
9/16"
3/8
12 415 0638
11/16"
3/8
12 415 0738
11/16"
1/2
12 415 0748
7/8"
G
ØS 5/32"
C
B B
CAUTION: Straight Stem Adapters should not be used in conjunction with other union type fittings in applications where vibration is present, nor should they be used as “quick disconnects” as the mating nickel plated brass surfaces may wear over time causing eventual failure of the connection.
CAUTION: Straight Stem Adapters should not be used in conjunction with other union type fittings in applications where vibration is present, nor should they be used as “quick disconnects” as the mating nickel plated brass surfaces may wear over time causing eventual failure of the connection.
6
8
10
12
Pneufit Stem Adapter (Inch O.D. Stem to ISO R Thread) L
A Stem O.D.
G ØA
Part Number
1/8
10 115 0418
1/4
10 115 0428
1/8
12 115 0418
1/4
12 115 0428
1/8
10 115 0518
1/4
10 115 0528
1/4
12 115 0628
3/8
12 115 0638
3/8
12 115 0738
1/2
12 115 0748
5/32
ØS C
B ISO R Thread
B B
CAUTION: Straight Stem Adapters should not be used inconjunction with other union type fittings in applications where vibration is present, nor should they be used as “quick disconnects” as the mating nickel plated brass surfaces may wear over time causing eventual failure of the connection.
1/4
5/16
3/8
1/2
Pneufit C Stem Adapter (Inch O.D. Stem to ISO R Thread) A