IdeaCentre K3 Series. Hardware Replacement Guide. Version

IdeaCentre K3 Series Hardware Replacement Guide Version 1.1 2009.10 31041387 31041387_K3_HRG_FM_EN_V1.1.indd 1 2009.10.23 10:34:44 AM Hardware ...
Author: Barnard French
7 downloads 0 Views 3MB Size
IdeaCentre K3 Series Hardware Replacement Guide

Version 1.1

2009.10

31041387

31041387_K3_HRG_FM_EN_V1.1.indd 1

2009.10.23 10:34:44 AM

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 1

2009.10.23 10:29:53 AM

Contents Overview ..................................................................................... 1 Chapter 1 Locations ................................................................. 4 Locating components and connectors............................................4 Identifying parts on the system board ............................................7

Chapter 2 Replacing hardware . .............................................. 9 General information.........................................................................9 Removing the computer cover .......................................................9 Removing the front bezel..............................................................11 Replacing a memory module .......................................................12 Replacing the hard disk drive........................................................13 Replacing an optical drive.............................................................14 Replacing the system fan assembly..............................................15 Replacing the heat sink assembly ................................................18 Replacing a PCI or AGP adapter . ................................................20 Replacing the CPU.......................................................................26 Replacing the keyboard ...............................................................29 Replacing the mouse ...................................................................30 Replacing the External speaker . ..................................................31 Completing the installation ...........................................................31

Appendix.................................................................................... 33

31041387_K3_HRG_EN_V1.1.indd 2

2009.10.23 10:29:53 AM

Overview This guide is intended to be used by customers who are replacing Customer Replaceable Units (CRUs) as well as trained service personnel who are replacing Field Replaceable Units (FRUs). In this guide, CRUs and FRUs will often be referred to as parts. Note: Trained service personnel should refer to the Hardware Maintenance Manual (HMM) for parts ordering information. This guide does not include procedures for all parts. It is expected that cables, switches, and certain mechanical parts can be replaced by trained service personnel without the need for step-by-step procedures. Note: Use only parts provided by Lenovo®. The description of the TV-Tuner card in this manual applies only to those computer models that have the TV-Tuner card installed. It does not apply to those computer models that do not have the TV-Tuner card installed. This guide contains procedures for replacing the following parts: • Memory modules • Hard disk drive • Optical drive • Heatsink, Fan • CPU • VGA card • Keyboard, Mouse (wired) • External speaker

Safety information for replacing CRUs Do not open your computer or attempt any repair before reading the “Important safety information” in the Safety and Warranty Guide that was included with your computer. If you no longer have this copy of the Safety and Warranty Guide, you can obtain one online from the Support Web site at http://consumersupport.lenovo.com. Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 1



2009.10.23 10:29:53 AM

Additional information resources If you have Internet access, the most up-to-date information for your computer is available from the World Wide Web. You can find the following information: • CRU removal and installation information • Publications • Troubleshooting information • Parts information • Links to other useful sources of information To access this information, go to http://consumersupport.lenovo.com.

Tools required To disassemble the computer, you need the following tools: • Wrist grounding strap and conductive mat for preventing electrostatic discharge • Flat screwdriver • Phillips screwdriver • Hex screwdriver • Plastic flat screwdriver • Plastic tweezers Note: The screws for the different components vary in size. During the disassembly procedure, group the screws with their corresponding components to avoid a mismatch when replacing the components.

Handling static-sensitive devices Static electricity, although harmless to you, can seriously damage computer components. When you are replacing a part, do not open the static-protective package containing the new part until the defective part has been removed from the computer and you are ready to install the new part. When you handle parts and other computer components, take these precautions to avoid static-electricity damage:



Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 2

2009.10.23 10:29:54 AM

• Limit your movement. Movement can cause static-electricity to build up around you. • Always handle parts and other computer components carefully. Handle adapters, memory modules, system boards, and microprocessors by the edges. Never touch any exposed circuitry. • Prevent others from touching the parts and other computer components. • Before you replace a new part, touch the static-protective package containing the part to a metal expansion-slot cover or other unpainted metal surface on the computer for at least two seconds. This reduces static electricity in the package and your body. • When possible, remove the new part from the static-protective packaging, and install it directly in the computer without setting the part down. When this is not possible, place the static-protective package that the part came in on a smooth, level surface and place the part on it. • Do not place the part on the computer cover or other metal surface.

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 3



2009.10.23 10:29:54 AM

Locations

Chapter

This chapter provides illustrations to help locate the various connectors, controls and components of the computer. To remove the computer cover, refer to “Removing the computer cover”.

Locating components and connectors The following illustrations will help you to locate the various components and connectors in your computer.

Internal components The following illustration shows the components inside your computer.

8

1 2 3 4

5

6

7



Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 4

2009.10.23 10:29:55 AM

Power supply

PCI Express adapter card

System fan

Memory modules

Microprocessor fan and heat sink

Hard disk drive

PCI Express adapter connector

Optical drive

Front view The following illustrations show the location of connectors on the front of the computer. 1 2 3 7

4 5 6 8

9

Power button Power Dial indicator ON/OFF File backup button USB connector Microphone connector Headphone connector Memory card reader (selected models only)

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 5



2009.10.23 10:29:56 AM

Optical drive (Some models are equipped with only one optical drive.) Power Dial switch

Rear view The following illustration shows the location of connectors on the rear of the computer.

1 2

3

4

5 6 7 9 10

8 11 12 13 14

Voltage selection switch (selected models only) Power connector PS/2 keyboard connector PS/2 mouse connector Serial connector (selected models only) On-board VGA connector (selected models only) USB connectors (6) Ethernet connector Microphone connector Audio line-out connector Audio line-in connector



Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 6

2009.10.23 10:29:58 AM

PCI Express x16 graphics adapter connector (Some models are equipped with this connector. For more information about the graphics adapter, see the description below). WiFi antenna connector (This connector only equipped on the model with WiFi card. For more information about this connector, see WM600-B-LO Wireless 802. 11b/g Wireless PCI-E Adapter Card User Manual.) TV-Tuner(selected models only)

Identifying parts on the system board The system board (sometimes called the planar or motherboard) is the main circuit board in your computer. It provides basic computer functions and supports a variety of devices that are factory-installed or that you can install later. The following illustration shows the locations of parts on the system board.

12V power connector Microprocessor and heat sink Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 7



2009.10.23 10:29:59 AM

Microprocessor fan connector Memory connectors(2) Memory connectors(2) Thermal sensor header connector Power connector E-SATA connector SATA IDE connectors(3) Front panel connector Front USB connectors(3) Serial (com2) connector Power fan connector Front audio connector PCI adapter connector PCI Express x1 adapter connectors(2) PCI Express x16 graphics adapter connector System fan connector



Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 8

2009.10.23 10:30:00 AM

Chapter

Replacing hardware

Attention:

Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://consumersupport.lenovo.com. Note: Use only parts provided by Lenovo.

General information Pre-disassembly instructions Before proceeding with the disassembly procedure, make sure that you do the following: 1. Turn off the power to the system and all peripherals. 2. Unplug all power and signal cables from the computer. 3. Place the system on a flat, stable surface.

Removing the computer cover Attention:

Turn off the computer and wait 3 to 5 minutes to let the computer cool before removing the computer cover.

To remove the computer cover: 1. Remove any media (diskettes, CDs, or memory cards) from the drives, shut down your operating system, turn off all attached devices, and the computer. 2. Unplug all power cords from electrical outlets.

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 9



2009.10.23 10:30:00 AM

3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to “Locating connectors on the rear of the computer”. 4. Remove the two screws that secure the computer cover at the rear of the chassis. 5. Slide the computer cover to the rear of the chassis to remove. Note: For this procedure, it helps to lay the computer on its side.

10

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 10

2009.10.23 10:30:10 AM

Removing the front bezel To remove the front bezel: 1. Remove the computer cover. Refer to “Removing the computer cover”. Note: For this procedure, it helps to lay the computer on its side. 2. Remove the front bezel by releasing the three plastic tabs inside the chassis and push the bezel outward as shown.

3. To reinstall the bezel, align the plastic tabs on the bottom of the bezel with the corresponding holes in the chassis, and then snap it into position at the bottom and top of the chassis. 4. Refer to the “Completing the installation”.

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 11

11

2009.10.23 10:30:22 AM

Replacing a memory module

Attention: Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://consumersupport.lenovo.com.

To replace a memory module: 1. Remove the computer cover. Refer to “Removing the computer cover”. Note: For this procedure, it helps to lay the computer on its side. 2. Locate the memory module connectors. Refer to “Locating components”. 3. Remove the memory module being replaced by opening the retaining clips as shown.

4. Position the new memory module over the memory connector. Make sure the notch on the memory aligns correctly with the connector key on the system board. Push the memory module straight down into the connector until the retaining clips close.

5. Refer to the “Completing the installation”.

12

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 12

2009.10.23 10:30:23 AM

Replacing the hard disk drive

Attention: Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://consumersupport.lenovo.com.

To replace the hard disk drive: 1. Remove the computer cover. Refer to “Removing the computer cover”. Note: For this procedure, it helps to lay the computer on its side. 2. Disconnect the data and power cables from the hard disk drive. 3. Use the plastic handle to slide the hard disk drive out of the drive bay.

4. Slide the new hard disk drive into the drive bay. 5. Pivot in the drive bay in place. 6. Connect the power and signal cables to the hard disk drive. Refer to “Identifying parts on the system board”. Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 13

13

2009.10.23 10:30:33 AM

7. Refer to the “Completing the installation”.

Replacing an optical drive

Attention: Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://consumersupport.lenovo.com

To replace an optical drive 1. Remove the computer cover. Refer to “Removing the computer cover”. 2. Remove the front bezel. Refer to “Removing the front bezel”. 3. Disconnect the data and power cables from the rear of the optical drive. 4. Press the release button and push the optical drive straight out of the front of the chassis.

14

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 14

2009.10.23 10:30:42 AM

5. Slide the new optical drive into the bay from the front until it snaps into position. 6. Connect the data and power cables to the drive. 7. Install the front bezel. Refer to the steps 3 of the “Removing the front bezel”. 8. Install the computer cover. Refer to “Completing the installation”.

Replacing the system fan assembly

Attention: Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://consumersupport.lenovo.com

To replace the system fan assembly: 1. Remove the computer cover. Refer to “Removing the computer cover”. 2. Locate the system fan assembly. Refer to “Identifying parts on the system board”. 3. Disconnect the system fan assembly cable from the system board. Refer to “Identifying parts on the system board”.

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 15

15

2009.10.23 10:30:43 AM

4. Pull the system fan assembly out of chassis.

16

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 16

2009.10.23 10:30:44 AM

5. Install the new system fan assembly by aligning the rubber mounts of the system fan assembly with the holes on the chassis and push the rubber mounts through the holes.

6. Pull on the tips of the rubber mounts until the fan assembly is in place. 7. Connect the system fan assembly cable to the system fan connector on the system board. 8. Refer to the “Completing the installation”.

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 17

17

2009.10.23 10:30:53 AM

Replacing the heat sink assembly Attention:

Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at: http://consumersupport.lenovo.com

To replace the heat sink assembly: 1. Remove the computer cover. Refer to “Removing the computer cover”. 2. Lay the computer on its side. 3. Locate the heat sink. Refer to “Identifying parts on the system board”. 4. Disconnect the heat sink and the fan assembly cable from the system board. 5. Remove the four screws system board.

securing the heat sink and fan assembly to the

6. Lift the failing heat sink and fan assembly off the system board. 7. Use the thermal grease syringe to place five drops of grease on the top of the microprocessor. Each drop of grease should be 0.03ml (3 tick marks on the grease syringe).

18

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 18

2009.10.23 10:31:03 AM

8. Install the heat sink and fan assembly on the heat sink retention bracket. 9. Reconnect the disconnected cables to the system board. 10. Refer to the “Completing the installation”.

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 19

19

2009.10.23 10:31:03 AM

Replacing a PCI or AGP adapter Attention:

Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at: http://consumersupport.lenovo.com

To replace an adapter: 1. Remove the computer cover. Refer to “Removing the computer cover”. to open the adapter 2. At the rear of the computer, press the release button latch and remove the adapter by pulling it straight out of the adapter connector.

20

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 20

2009.10.23 10:31:05 AM

3. Install the new adapter into the same adapter connector.

4. Ensure the adapter is fully seated into the adapter connector. 5. At the rear of the computer, pivot the adapter latch to the closed position to secure the adapter. 6. Refer to the “Completing the installation”.

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 21

21

2009.10.23 10:31:07 AM



Note 1: Replacement of some models equipped with graphic adapter bracket is different.

Please remove the plastic bracket first as the following: 1. Remove the two screws that secure the plastic bracket at the bottom of the chassis. 2. Lift the plastic bracket out of the chassis. 3. Then remove the adapter as above.

After the Graphic Adapter is installed , install the bracket as the following: 1. Install the plastic bracket into the chassis so that the screw holes in the plastic bracket align with those in the chassis. Let the slot on the plastic bracket clip the adapter.

22

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 22

2009.10.23 10:31:11 AM

2. Install the two screws to secure the plastic bracket. Note: Use only the screws provided by Lenovo.

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 23

23

2009.10.23 10:31:14 AM



Note 2: Replacement of some models equipped with graphic adapter bracket is different.

Please remove the bracket first as the following: 1. Remove the screw that secures the bracket at the side of the chassis. 2. Press the pin on one end of the metal bracket and pull the metal bracket straight out of the chassis.

After the Graphic Adapter is installed, install the bracket as the following: 1. Install the metal bracket into the chassis so that the screw hole in the metal bracket aligns with the hole in the chassis. Let the slot on the metal bracket clip the adapter.

24

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 24

2009.10.23 10:31:24 AM

2. Screw back the screws on the metal bracket. Note: Use only the screw provided by Lenovo.

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 25

25

2009.10.23 10:31:43 AM

Replacing the CPU Attention:

Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://consumersupport.lenovo.com

To replace an CPU 1. Remove the computer cover. Refer to “Removing the computer cover”. 2. Remove the front bezel. Refer to “Removing the front bezel”. 3. Remove the system board. Refer to “Replacing the heat sink assembly”. 4. Remove the heat sink and fan assembly. Refer to “Replacing the heat sink assembly”. 5. To remove the microprocessor and open the retainer .



26

from the system board, lift the small handle

Important: Do not touch the gold contacts on the bottom of the microprocessor. When handling the microprocessor, touch only the sides.

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 26

2009.10.23 10:31:54 AM

6. Lift the microprocessor straight up and out of the socket.

Notes: a. Note the orientation of the notches on the microprocessor. This is important when reinstalling the microprocessor on the new system board.

b. Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be kept as clean as possible. 7. Make sure that the microprocessor retainer is fully open. 8. Holding the microprocessor with your fingers, remove the protective cover that protects the gold contacts on the new microprocessor .

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 27

27

2009.10.23 10:31:55 AM

9. Holding the microprocessor with your fingers, position the microprocessor so that the notches on the microprocessor are aligned with the tabs in the microprocessor socket.

Important: To avoid damaging the microprocessor contacts, do not tilt the microprocessor when installing it into the socket.

10. Lower the microprocessor straight down into the system board socket of the system board.

11. To secure the microprocessor in the socket, close the microprocessor retainer and lock it into position with the small handle. 12. Use the thermal grease syringe to place five drops of grease on the top of the microprocessor. Each drop of grease should be 0.03ml (3 tick marks on the grease syringe).

13. Install the heat sink and fan assembly on the system board. 14. Connect the heat sink and fan assembly cable to the system board. Refer to the “Identifying parts on the system board”. 15. Install the system board into the chassis and allign the screw holes with those in the chassis.Insert and tighten the screws that secure the system board. Refer to the “Replacing the system board”. 16. Reconnect the disconnected cables to the system board. 17. Refer to the “Completing the installation”.

28

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 28

2009.10.23 10:31:55 AM

Replacing the keyboard To replace the keyboard: 1. Remove any media (diskettes, CDs, or memory cards) from the drives, shut down your operating system, and turn off all attached devices and the computer. 2. Unplug all power cords from electrical outlets. 3. Locate the connector for the keyboard. Refer to “Locating connectors on the rear of the computer” and “Locating connectors on the front of the computer”. Note: Your keyboard might be connected to the standard keyboard connector at the rear of the computer or to a USB connector at either the front or rear of the computer.

4. Disconnect the failing keyboard cable from the computer and connect the new keyboard cable to the same connector. 5. Refer to the “Completing the installation”.

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 29

29

2009.10.23 10:31:55 AM

Replacing the mouse To replace the mouse: 1. Remove any media (diskettes, CDs, or memory cards) from the drives, shut down your operating system, and turn off all attached devices and the computer. 2. Unplug all power cords from electrical outlets. 3. Locate the connector for the mouse. Refer to “Locating connectors on the front of the computer” and “Locating connectors on the rear of the computer”. Note: Your mouse might be connected to the standard mouse connector at the rear of the computer or to a USB connector at either the front or rear of the computer.

4. Disconnect the failing mouse cable from the computer. 5. Connect the new mouse cable to the connector. 6. Refer to the “Completing the installation.”

30

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 30

2009.10.23 10:31:56 AM

Replacing the External speaker 1. Remove any media (diskettes, CDs, or memory cards) from the drives, shut down the computer, and turn off all attached devices. 2. Unplug all power cords from electrical outlets. 3. Locate the Speaker. Refer to “Locating connectors on the rear of the computer” and “Locating connectors on the front of the computer”. Your speaker might be connected to the Audio connector to an Audio connector at either the front or rear of the computer. Locate the connector for the speaker.

4. Disconnect the failing speaker cable from the computer and connect the new speaker cable to the same connector.

Completing the installation After replacing the parts, you need to close the computer cover and reconnect cables, including telephone lines and power cords. Also, depending on the part that was replaced, you might need to confirm the updated information in the Setup Utility program. Refer to “Starting the Setup Utility” in the User Guide or in the Hardware Maintenance Manual.

To complete the part installation: 1. Ensure that all components have been reassembled correctly and that no tools or loose screws are left inside your computer. Refer to “Locating components” for the location of the various components. 2. Make sure that the cables are routed correctly before replacing the computer cover.

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 31

31

2009.10.23 10:31:56 AM

3. Position the computer cover on the chassis so that the rail guides on the bottom of the computer cover engage the rails. Then, push the computer cover closed until it snaps into position.

4. Reconnect the external cables and power cords into the computer. Refer to “Locating connectors on the front of the computer” and “Locating connectors on the rear of the computer”. 5. To update your configuration settings, refer to “Starting the Setup Utility” in the User Guide or in the Hardware Maintenance Manual. Note: In most areas of the world, Lenovo requires the return of the defective CRU. Information about this will come with the CRU or will come a few days after the CRU arrives.

32

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 32

2009.10.23 10:32:06 AM

Appendix. Statement Thanks for using Lenovo products. Carefully read all of the documents shipped with your computer before you install and use the product for the first time. Lenovo will not assume responsibility for damage that results from failure to operate the product according to instructions and requirements described in the manuals included with your computer. Lenovo will not assume responsibility for any loss caused except that caused by the installation or operations carried out by Lenovo professional service staff. Lenovo has made every attempt to ensure that the manuals included with your computer, are correct and accurate, but makes no guarantee that the publications are error free. To provide better service, Lenovo reserves the right to improve and/or modify the products and software programs described in the manuals included with your computer and the content of the manual at any time without additional notice. All of the manuals included with your computer are provided to help you use Lenovo products appropriately, but do not provide any description of the software/ hardware configuration for the product. For the configuration of the product, refer to related contract (if any), product packing list for the product or retailer. The content of the manuals included with your computer is protected by copyright laws and rules. None of the manuals included with your computer may be reproduced or transcribed by any means, or transmitted through wired or wireless network in any form, or translated into any language without prior written permission of Lenovo. All Lenovo publications included with your system are protected by Copyright © 2007, 2009 Lenovo. The software and hardware configuration included with your computer depends on the actual configuration of the computer and may differ from other similar models. Customers are welcome to contact us for any inconsistency between the product and the manuals included with your computer. For the latest information or any questions or comments, please visit consumer support website at: http://consumersupport.lenovo.com

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 33

33

2009.10.23 10:32:17 AM

Lenovo is a registered trademark of Lenovo. Microsoft, Windows, and Windows Vista are trademarks of the Microsoft group of companies. Intel Inside is the registered trademark of Intel. AMD, the AMD Arrow logo, ATI, the ATI logo, AMD Athlon, AMD LIVE, AMD Opteron, AMD Phenom, AMD Sempron, Avivo, Catalyst, Cool 'n' Quiet, CrossFireX, Overdrive, Powerplay, Radeon, The Ultimate Visual Experience, and combinations thereof are trademarks of Advanced Micro Devices, Inc. in the United States and/ or other jurisdictions. The table above includes the logo and registered trademarks of Lenovo and its partners. Other registered trademarks mentioned in all the manuals included with your computer belong to the specific company respectively. The manual included with your computer is protected by copyright laws and rules. None of the manuals included with your computer may be reproduced or transcribed by any means, or transmitted through wired or wireless network in any form, or translated into any language without prior written permission of Lenovo. Names or marks of certain companies mentioned in the manuals included with your computer or this document are only used to state trademark rights, and they will not necessarily indicate that related software or hardware is included. The concrete configuration of the product depends on the description of the specific model.

34

Hardware Replacement Guide

31041387_K3_HRG_EN_V1.1.indd 34

2009.10.23 10:32:18 AM