I-STORM LAN ROUTER ADSL with 4 Fast Ethernet ports + 1 USB port

Quick Start Guide A02-RA2+/G2 (February 2004)V1.10

1

I-Storm LAN Router ADSL For more detailed instructions on configuring and using the IStorm Lan Router ADSL, please refer to the online manual. Before beginning the configuration of the Router you have to know the parameters of your subscription ADSL. There are five ways ─ PPPoE, PPPoA, RFC1483 routed, IPoA, RFC1483 Bridge─ for the device to have a public IP address and then to access Internet. You have to check with your ISP about which way is adopted. VPI/VCI: Consult the telephone company to get the Virtual Path Identifier (VPI) and Virtual Channel Identifier (VCI) numbers. The valid range for the VPI is 0 to 255 and for the VCI is 32 to 65535. The default value VPI is 0 and VCI is 32. For BT (VPI=0, VCI=38) and for KC ((VPI=1, VCI=50). NAT: The NAT feature allows multiple-user Internet access for the cost of a single IP account. If you need to have a public server or a public network, NAT has to be disabled. Encapsulation Method: Be sure to use the encapsulation method (LLC/SNAP or VC MUX) required by your ISP. Gather the information as illustrated in the following table and keep it for reference. PPPoE

VPI and VCI VC-based / LLC-based multiplexing Username and Password Service Name

PPPoA

VPI and VCI VC-based / LLC-based multiplexing Username and Password

2

I-Storm LAN Router ADSL RFC1483 Bridged

VPI/VCI

RFC1483 Routed

VPI/VCI

VC-based / LLC-based multiplexing VC-based / LLC-based multiplexing IP address Subnet mask Default Gateway (IP address) IP address (DNS)

IPoA

VPI/VCI IP address Subnet mask Default Gateway (IP address) IP address (DNS)

1.1 Package contents Make sure that you have the following items: • I-Storm Lan Router ADSL • Network cable (CAT 5) • Cable USB • Cable RJ-11 ADSL • Power Adapter AC-DC (12V, 1A) • CD-ROM (with manual, software and driver) • This Quick Start Guide

3

I-Storm LAN Router ADSL 1.2 Cabling Plug one end of the RJ11 cable into the ADSL port on the rear panel of the Router and insert the other end into splitter , then connect to Rj45 ports by an Ethernet cable your PCs or Switch. Finally connect the Adapter to power inlet and turn the power switch on. Now the I-Storm LAN Router ADSL will enter a selftest phase for about ten seconds. After this phase the SYS led will be flashed to indicate that router is in normal operation. Now you should see the ADSL led first blinking during alignment and then steady when connection is on.

1.3 The Front Panel LEDs

Port 6

POWER

7

SYS

8

USB

9-12

LAN

Information Lit green when power adapter is connected. System status indicators when blinking indicate system is alive. Steady

green

light

indicates

a

valid

ADSL

connection. Blinking green light indicates an active WAN session.

4

I-Storm LAN Router ADSL

13

ADSL

When lit, it indicates that the ADSL (Line) port is connected to the DSLAM and working properly.

1.4 The Rear Ports

Port 1

Line(RJ11)

Meaning Connect the supplied RJ-11 cable to this port when connecting to the ADSL/telephone network.

2 3 4

5

6

USB

Reset LAN (4 connettori RJ-45)

Connect the USB cable to this port when Upgrading Firmware or connecting to PC Press it (10 sec) to restore the factory default setting back Connect a straight or crossover Ethernet cable to this port when connecting to PCs or Switch in the network

POWER (jack)

Connect the supplied power adapter to this jack

POWER Switch

Premere per accendere/spegnere il Router

5

I-Storm LAN Router ADSL 1.5 Default Settings Before you configure this I-Storm Lan Router ADSL , you need to know the following default settings. Leaving these settings, configuring the PCs such as DHCP client (follow the instructions below) and configuring ISP connection (You have to check with your ISP about which way is adopted) you can configure the I-Storm Lan Router ADSL quickly. For a more detailed configuration refer to manual on Installation CD. Below the I-Storm Lan Router ADSL default settings: •

User Name:admin

•

Password:Atlantis

•

IP Address (192.168.1.254)

•

Subnet Mask (255.255.255.0)

•

ISP Protocol =PPPoA con VCMux

•

DHCP Server active with IP range from 192.168.1.100 to 192.168.1.199

1.6 IE Configuration Now open IE, go to Instruments menu, select the Connections tab and select one of the following options: •

Never use remote connection

•

Use remote connection if another network connection isn’t available

Look the following picture.

6

I-Storm LAN Router ADSL

7

I-Storm LAN Router ADSL

1.7 TCP/IP Configuration Configuring PC (Windows 95/98/ME) 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2. 3.

Select TCP / IP -> NE2000 Compatible, or the name of any Network Interface Card (NIC) in your PC. Click Properties.

8

I-Storm LAN Router ADSL 4.

5. 6.

Select the IP Address tab. In this page, click the Obtain an IP address automatically radio button.

Then select the DNS Configuration tab. Select the Disable DNS radio button and click “OK” to finish the configuration.

9

I-Storm LAN Router ADSL

10

I-Storm LAN Router ADSL Configuring PC (Windows NT4.0) 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2.

Select TCP/IP Protocol and click Properties.

3.

Select the Obtain an IP address from a DHCP server radio button and click OK.

11

I-Storm LAN Router ADSL

12

I-Storm LAN Router ADSL Configuring PC (Windows 2000) 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2.

Double-click LAN Area Connection.

3.

In the LAN Area Connection Status window, click Properties.

13

I-Storm LAN Router ADSL

4.

Select Internet Protocol (TCP/IP) and click Properties.

14

I-Storm LAN Router ADSL

5.

Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons.

15

I-Storm LAN Router ADSL

6.

Click OK to finish the configuration.

16

I-Storm LAN Router ADSL Configuring (PC in WindowsXP) 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections. 2.

Double-click Local Area Connection.

3.

In the LAN Area Connection Status window, click Properties.

17

I-Storm LAN Router ADSL

4.

Select Internet Protocol (TCP/IP) and click Properties.

18

I-Storm LAN Router ADSL

5.

Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons.

19

I-Storm LAN Router ADSL

6.

Click OK to finish the configuration

1.6 Browser configuration Open the web browser, enter the local port IP address of this IStorm Lan Router ADSL, which default at 192.168.1.254, and click “Go” to get the login page.

The default username is admin, password Atlantis and click “OK” to continue.

20

I-Storm LAN Router ADSL

At the configuration homepage, the left navigation pane where bookmarks are provided links you directly to the desired setup page, including: •

STATUS (ADSL, LAN, PPP, Learned MAC Table, Routing Table, System Log, Security Log), • Quick Start • CONFIGURATION (WAN, LAN, System, Firewall, Virtual Server, Advanced) • Save Config to Flash. Click on the desired item to expand the page with all settings in the main navigation pane. Following next steps you can make operating I-Storm Lan Router ADSL in short time using DHCP mode on lan PCs. Refer to manual on Installation CD if you need personalized configuration. Selecting Quick Start, on the right of the screen will appear the frame where you can configure your ISP settings.

21

I-Storm LAN Router ADSL PPPoE(RFC 2516)/ PPPoA (RFC 2364) PPPoE (PPP over Ethernet) is known as a dial-up DSL or cable service. Like PPPoA it is designed to integrate the broadband services into the current widely deployed, easy-to-use, and low-cost dial-up-access networking infrastructure. Therefore, users can get greater access speed without changing the operation concept, sharing the same ISP account and paying for one access account. No PPPoE client software is required for local computer if you select this configuration. Look the following settings: Per PVC Setting • Virtual Circuit= Enabled Connection • Encapsulation= Select PPPoE LLC (or sometimes PPPoE VC-Mux) with PPPoE. With PPPoA select PPPoA VC-Mux (or PPPoA LLC) • Bridge=disabled • VPI=8 (ISP) • VCI=35 (ISP) Static IP Settings • Static IP Address=0.0.0.0 • Subnet Mask=0.0.0.0 • Gateway=0.0.0.0 Account Setup • Username provided by ISP: Enter the username provided by your ISP. Maximum input is 63 alphanumeric characters (case sensitive). • Password provided by ISP: Enter the password provided by your ISP. Maximum input is 63 alphanumeric characters (case sensitive).

22

I-Storm LAN Router ADSL Click on Submit, Save Config and finally on Submit.

RFC1483/RFC1577 How to configure WAN interface with statical IP provided by ISP. Look the following settings: Per PVC Setting • Virtual Circuit= Enabled Connection • Encapsulatio= 1483 Routed IP LLC or 1483 Routed IP VC-Mux. Chose Classical IP over ATM with RFC1577. • Bridge=disabled • VPI=8 (ISP) • VCI=35 (ISP) Static IP Settings • Static IP Address= Insert the statical IP provided by ISP. • Subnet Mask= Insert the Subnet Mask provided by ISP. • Gateway= Insert the Default Gateway of I-Storm Lan Router ADSL provided by ISP. Account Setup • Username: • Password: Click on Submit, Save Config and finally on Submit. The ADSL Router will reboot automatically. After reboot all pc of the network will be able to surf the Internet. DHCP server will be provide for each PC an IP address, Subnet Mask,

23

I-Storm LAN Router ADSL Default Gateway and DNS server. By these settings all packets sent to the LAN will be forwarded on the right client the other will be forwarded by the Default Gateway (Atlantis I-Storm LAN Router ADSL) to the Internet.

24