HPS. (High Performance Sliding) Doors HPX Monumental Sliding Doors. Hanging Tough Against Rain, Hail and Hurricanes

HPS (High Performance Sliding) Doors HPX Monumental Sliding Doors ® Hanging Tough Against Rain, Hail and Hurricanes Atlantis Casino and Resort, Para...
Author: Job Summers
12 downloads 0 Views 844KB Size
HPS (High Performance Sliding) Doors HPX Monumental Sliding Doors ®

Hanging Tough Against Rain, Hail and Hurricanes

Atlantis Casino and Resort, Paradise Island, Nassau, Bahamas Architect: HKS Architects, Dallas, TX Glazing Contractor: Commonwealth Building Supply Ltd., Nassau, Bahamas

Kawneer’s HPS®/HPX Sliding Doors meet the most stringent design criteria and withstand the worst kind of weather. Monumental in design and providing the highest performance for wind load and water resistance, these sliding doors have also been hurricane impact and cycle tested by an independent laboratory to meet the requirements of the Florida Building Code and International Building Code.

Performance HPS® Sliding Doors are available in four different performance ranges for all types of applications, including high-rise. Meeting or exceeding all criteria established by the American Architectural Manufacturers Association (AAMA), they are certified for performance classes and grades of HC60, HC80, HC100 and HC120. For example, a performance designation of HC120 indicates that the product has been tested at a structural load of 180 psf. HPS® Sliding Doors

withstand water infiltration that exceeds the minimum test standard requirements – sufficient to endure heavy rains at high pressures. They also meet both AAMA’s Operating Force requirements and Forced Entry Resistance requirements in accordance with AAMA 1303.5. HPS® Sliding Doors have been small missile impact and cycle tested to withstand hurricanes. The small missile test involves simulating windborne roof gravel damage and is used for products installed more than 30 feet above ground. Three identical test units are positioned opposite an air cannon containing 2 gram steel ball bearings, which are fired at the test specimens at 130 feet per second (88 mph) for a total of 30 impacts per specimen. No penetration may occur. Both large and small missile tests are followed by a severe cyclic pressure test in which the impacted test units are subjected to a series of 4,500 inward and 4,500 outward pressure cycles (up to the design pressure) that simulate wind forces in a hurricane. Large missile hurricane impact These take place every one to tested HPX Slider three seconds for an extended period of time. No significant opening through which air can pass may occur. HPS® Sliding Doors have been cycle tested at design pressures of +90/-125 psf. HPX Sliding Doors meet even more extreme conditions with taller and heavier sections for monumental applications such as high-rise coastal buildings up to 40 stories that require superior wind load and water performance as well as the ability to retain structural integrity during the toughest kind of hurricane. HPX test results are some of the highest in the industry and have been cycle tested to +130/-180 psf design pressures and higher. HPX Sliding Doors withstand water infiltration at 32 psf – sufficient to endure the heaviest rains at extreme pressures. HPX Sliding Doors have been large missile impact tested to simulate large wind-borne debris that may occur during hurricanes. The test is used for products installed up to 30 feet above ground. Three identical test units are positioned opposite an air cannon containing a 9 lb. two-by-four timber which is fired at 50 feet per second (34 mph). Each unit must resist penetration by strikes at strategically different points: for example, at the center and six inches from one corner of the glazing and other areas on the door. No penetration may occur. This test is also followed by a cyclic pressure test. HPX Sliding Doors also meet both the Operating Force requirements of AAMA and the requirements for Forced Entry Resistance in accordance with ASTM F-588.

Kawneer Company, Inc. Technology Park / Atlanta 555 Guthridge Court Norcross, GA 30092 © Kawneer Company, Inc. 2007

kawneer.com 770 . 449 . 5555

LITHO IN U.S.A

Form No. 07-2008

Realm Condominiums, Atlanta, GA Architect: The Preston Partnership, LLC, Atlanta, GA Glazing Contractor: Glass Systems, Inc., Lithonia, GA

Aesthetics Monumental in appearance, HPS® and HPX Sliding Doors have larger, wider and deeper sections than regular sliders, and are available in four standard configurations: OX, XO, OXO and OXXO. Other configurations are possible with the addition of a fixed mullion for HPS®. Sightlines for both doors vary depending upon the configuration of panels. HPS® Sliding Doors have the appearance of a storefront type system with a 3" high sill track to meet higher water performance standards. Overall system depth is 5-9/16 inches. Infill options for HPS® Sliding Doors range from 1/4" to 1", and include 9/16" impact resistant laminated glass. Factory glazing is available for the sliding panels. Three performance ranges of interlocks meet various structural designs. HPX Sliding Doors offer similar configurations and options. The larger interlocks and stiles are designed to meet higher structural loads. Overall system depth is 6 inches. The standard infill is 5/8" impact resistant, glassclad polycarbonate. Other infills for nonimpact applications range from 3/8" to 7/8 inch. HPX Sliding Doors also offer the ability to pre-glaze panels, and factory glazing is available for both fixed and sliding panels. Stainless steel track inserts and adjustable stainless steel tandem roller assemblies with ball bearings ensure smooth operation in both doors. The Adams-Rite 1847 all stainless steel deadlock is available in both doors and provides dependable security and durability.

HPX Sliding Doors

AUGUST, 2016

FEATURES

Features • Superior structural and water resistance • Hurricane Cycle tested to +130/-215 psf design pressures. • Water resistance exceeds 32 psf. • Meets South Florida Building Code and SBCCI SSTD 12 for Large and Small Missile Impact Resistance • Forced Entry Resistance tested per ASTM F842 • Available as OX, XO, OXO and OXXO configurations • Accommodates 1/4", 3/8", 9/16", 5/8" and 7/8" infills • Heavy duty stainless steel casters • Stainless steel track insert for sliding panels • Optional factory glazing, both fixed and sliding panels • Stainless steel MS Hookbolt Lock • Optional architectural finishes including anodized and applied coatings • Interior insect screens

© Kawneer Company, Inc., 2010

Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement.

Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor.

EC 97911-112

kawneer.com

ADMB060EN

1

Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor.

HPX Sliding Doors

BLANK PAGE

ADMB060EN

kawneer.com

© Kawneer Company, Inc., 2010

Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement.

2 AUGUST, 2016 EC 97911-112

HPX Sliding Doors

AUGUST, 2016

INDEX

ELEVATIONS ...................................................................4 STANDARD DETAILS.....................................................5 thru 7 INSECT SCREENS / INFILL OPTIONS...........................7, 8 HARDWARE OPTIONS...................................................9

LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR. Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses ( ) are millimeters unless otherwise noted.

© Kawneer Company, Inc., 2010

Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement.

Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor.

EC 97911-112

The following metric (SI ) units are found in these details: m – meter cm – centimeter mm – millimeter s – second Pa – pascal MPa – megapascal Kawneer reserves the right to change configurations without prior notice when deemed necessary for product improvement.

kawneer.com

ADMB060EN

3

5

UNIT HEIGHT

UNIT HEIGHT

4

UNIT WIDTH 1

5

4

6

5

4

1

SLIDE

O X

6 7

8 5

OPP.

2 4

6

9

2

2

ADMB060EN

SLIDE FIXED

X O

7 6 5

OPP. OPP. OPP.

2 2

5 4

OX UNIT XO UNIT

UNIT WIDTH UNIT WIDTH

3 1 3 3 1 3

FIXED SLIDE FIXED FIXED SLIDE FIXED

O X O O X O

8 6 5

OPP. OPP. OPP.

4 2

OXO UNIT

3 1 1 3

FIXED

SLIDE

SLIDE

FIXED

O

X

X

O

6

5

OPP.

OPP. 4

OXO UNIT

UNIT WIDTH

4

OXXO UNIT

kawneer.com

© Kawneer Company, Inc., 2010

ELEVATIONS

Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor.

HPX Sliding Doors

Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement.

FIXED

UNIT HEIGHT

3

UNIT HEIGHT

UNIT HEIGHT

4 AUGUST, 2016 EC 97911-112

ELEVATIONS ARE NUMBER KEYED TO DETAILS UNIT WIDTH 3

© Kawneer Company, Inc., 2010

4-7/32" (107.15)

Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement.

UNIT HEIGHT

4-11/32" (110.33)

Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor.

AUGUST, 2016

kawneer.com

HPX Sliding Doors

EC 97911-112 STANDARD DETAILS

SCALE 3" = 1'-0' NOTE: 9/16" INFILL SHOWN. FOR ADDITIONAL GLAZING OPTIONS SEE PAGE 8.

6-3/32" (154.78)

OPERABLE HEAD FIXED HEAD

1 3

6-3/4" (171.45)

OPERABLE SILL FIXED SILL

2 4

ADMB060EN

5

1-1/4" (31.75) 4-3/16" (106.4)

2-15/16" (74.6)

UNIT WIDTH

FIXED JAMB INTERLOCK STILE LOCK JAMB

5 6 7

2-15/16" (74.6) 2-11/16" (68.3)

LOCK STILE MULLION

1/8"(3.2)

8

2-31/32" (75.4)

ADMB060EN

3-17/32" (89.7)

MEETING STILES

9

kawneer.com

© Kawneer Company, Inc., 2010

STANDARD DETAILS

Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor.

HPX Sliding Doors

Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement.

6 AUGUST, 2016 EC 97911-112

SCALE 3" = 1'-0"

© Kawneer Company, Inc., 2010

Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement.

kawneer.com

2"

2"

1"

1"

Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor.

AUGUST, 2016

HPX Sliding Doors

EC 97911-112 STANDARD DETAILS

SCALE 3" = 1'-0" OPTIONAL MEMBERS

HEAD RECEPTOR EXTERIOR GLAZED HEAD RECEPTOR INTERIOR GLAZED

NOTE: Head receptors cannot be used with insect screens.

ADMB060EN

7

SCALE 3" = 1'-0"

HEAD

SILL

NOTE: Standard screen includes plated steel hardware. Optional screen available with stainless steel hardware.

SCREEN WITH APPLIED CLOSURE FOR SCREEN LATCH

INTERLOCK

1/4" LOCK JAMB

INFILL OPTIONS

3/8"

9/16"

ADMB060EN

7/8"

5/8"

NOTE: 5/8" INFILL SHOWN GLAZED WITH SILICONE FOR LARGE MISSLE IMPACT RESISTANCE.

kawneer.com

© Kawneer Company, Inc., 2010

INSECT SCREENS / INFILL OPTIONS

Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor.

HPX Sliding Doors

Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement.

INSECT SCREEN

8 AUGUST, 2016 EC 97911-112

INTERIOR SCREENS

INSECT SCREEN

HPX Sliding Doors

AUGUST, 2016 EC 97911-112

HARDWARE OPTIONS

Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor.

HARDWARE DESCRIPTION

OX, XO, OOX, XOO and OXO

(Interior) Extruded Pull with Thumbturn (Exterior) Blank Extruded Pull

OX, XO, OOX, XOO and OXO

(Interior) Extruded Pull with Thumbturn (Lock Panel) (Exterior) Blank Flush Pull

OX, XO, OOX, XOO and OXO

(Interior) Extruded Pull with Thumbturn (Lock Panel) (Exterior) Extruded Full Length Pull

OXXO

(Interior) Hurricane Thumbturn

All Configurations

© Kawneer Company, Inc., 2010

Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement.

MS ADAMS RITE 1847 LOCK

(Interior) Extruded Pull with Thumbturn (Exterior) Extruded Pull with Applied Cylinder

kawneer.com

9

ADMB060EN

WIND LOAD CHARTS

FOR WINDLOAD OR DEADLOAD INFORMATION, PLEASE CONTACT YOUR KAWNEER APPLICATION ENGINEERING DEPARTMENT.

ADMB060EN

Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor.

HPX Sliding Doors

kawneer.com

© Kawneer Company, Inc., 2010

Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement.

10 AUGUST, 2016 EC 97911-112

Suggest Documents