HD-SDI Transmitter/ Receiver/ Repeater with Power & Data

HD-SDI TRANSMISSION SOLUTIONS OVER COAX SC-HTP0601D, SC-HLR01D, SC-HRP0601D

User's Guide

SC-HTP0601D, SC-HLR01D, SC-HRP0601D

Release Version 1.0

Precaution and Safety Guidelines Please read this user’s manual thoroughly prior to use the unit for its easy and convenient use. • Do not install the product in the following places: extremely low or high temperature conditions; places exposed to rain, snow, or high humidity; places containing or exposed to oil and gas; places exposed to vibration and shock; places under direct sunlight or exposed to outdoor weather conditions; places exposed to radio waves (RF) or near to power lines. It may cause low performance or malfunction of the unit. • Do not disassemble the product or insert foreign objects. • The unit is subject to electric shock hazard. Be careful not to get an electric shock while using the device. • Please use only electrical safety approved power supply unit with electromagnetic compatibility. • Do not use and/or connect any devices inappropriate to the unit. It may cause malfunction of the unit or fire. • Use this product under temperature conditions only between - 10°C and +50°C. • Should be careful not to have the lines changed when connecting them. • Prior to turn on the device, check the cable insulation condition of the data cable, connected with external devices. • Before installing the product, check its voltage rate and then turn on the power. • Make sure to turn off the product prior to installation. • Do not subject the product to physical shock or exert excessive force to operate the product. • Do not use the device when any smoke or smell is produced from the unit. It may be subject to fire or electric shock. If any smoke or smell is produced, please turn off the unit and remove the power cable immediately, and contact your distributor to check the device properly. • If the power does not turn ON, please check whether the power cable is connected correctly or not. • Please note the transmission distance may vary depending on the cable quality and its loop resistance. Please refer to the transmission distance reference table per type of coaxial cable. • If the device does not work properly, please contact your distributor.

- 1 -

Release Version 1.0

1. Introduction 1.1 Overview

Using our HD-SDI transmission solutions (SC-HCP0601D, SC-HLR01D), you can transmit HD-SDI signal, Power (Max. 6W) and RS-485 over one coaxial cable up to 200M (HD: 1.485G) and 130M (full HD: 2.97G). The SC-HCP0601D is composed of a SC-HTP0601D (Transmitter) and a SC-HRP0601D (Receiver).Also the transmission distance can be extended up to 200M by using a repeater (SCHLR01D). This device can supply power to the camera and transmit the RS-485 data over 1 coaxial cable. Using SC-HCP0601D, as it is not necessary to wire the power cable or Data cable when installing the HD-SDI camera, it is cost-saving and easy installation solution.

1.2 Features

• “HD-SDI + Power + Data” Transmission over one coaxial cable. • Transmitting SDI signals up to 200m (HD: 1.485G), 130m (Full HD:2.97G) over RG-6 (Transmission distance can be extended by using a repeater, SC-HLR01D) • Bi-directional RS-485 Communication (Half Duplex) • No need of power/RS-485 data wiring for the camera or repeater in the middle • Installation improvement: Cost saving 30 ~ 50% • Possible to supply power to Megapixel camera (power consumption: Max.6W) with SC-HTP0601D (DC48V to DC12V down converter) and SC-HRP0601D (PoC power combiner) • Auto diagnosis for the cable status and safe power supply • Surge protection function • Distance extension repeater: SC-HLR01D (Max. 200m in HD transmission)

1.3 HD Signals Standards 



SeeEyes HD-SDI transmission solutions are conformed with the SDI signals standards of the SMPTE(Society of Motion Picture and Television Engineers) The SDI (Serial Digital Interface) signals transmission system is the innovative transmission system with which it can transmit incompressible video signals over one single cable. As the SDI signals are digital signals, it is possible to transmit limitless distance without modification by equalizing and re-clocking at each certain distance. Also, since the signals are incompressible signals, there is no aging or delay of video signals caused by the compression. SMPTE292M-HD-SDI

1.485 Gbps

SMPTE372M-Dual link - HD-SDI

2.97 Gbps

SMPTE424M-Dual speed - HD-SDI

2.97 Gbps

- 2 -

Release Version 1.0

2. Components 2.1 Transmitter and Receiver

Model #

Camera Power Supply (Tx.)

SCHTP0601D

○

Rx.

SCHLR01D

SCHRP0601D

○

Repeater

PSU (48V DC )

○

○

Design

Power cord, Adaptor

User’s Manual

OPTION

○

*Cautious • Possible to input control DATA only for SC-HLR01D, SC-HRP0601D • Possible to output control DATA only for SC-HTP0601D • Exclusive adaptor [DC48V / 1.04A] is optional • Power supply voltage should be between DC12V and DC 48V. • Should use DC 48V for supplying power to the camera • SC-HTP0601D cannot be powered from power supply and will be powered from SC-HLR01D or SC-HRP0601D over coaxial cable.

3. Product Parts & Peripheral Device Connection 3.1 Product Parts and Function

3.1.1 SC-HTP0601D(1CH transmitter) • The transmitter receives HD-SDI signals from the camera with HD-SDI IN port and transmits them over the coaxial cable to the receiver. (Recommended distance between the camera and SC-HTP0601D is Max.10m) • Using the SC-HRP0601D or SC-HLR01D, it receives DC48V from them and supplies power to the camera by down-converting to DC12V (The actual input power might be decreased by cable resistance or transmission distance.) • This device receives the Control DATA from HD-SDI OUT port and outputs the DATA through RS-485 output port. Also It is possible to control Camera OSD Menu. ②

③

①

④

- 3 -

Release Version 1.0

① ② ③

HD-SDI IN: Connect to the HD-SDI Camera with HD-SDI IN DC 12V, RS-485 OUT: Supply Power(DC 12V/0.5A(6W) for the camera and output RS-485 DATA Power / Video Indicator LED

LED Indicator Yellow ON Yellow OFF Green ON ④

Description Normal power supply Input power off Normal Operation (HD-SDI signal OUTPUT)

HD-SDI OUT: Connect the devices such as SC-HRP0601D(Rx.) , SC-HLR01D (Repeater) with HD-SDI OUT port over coaxial cable.

3.1.2 SC-HRP0601D(1CH receiver) • It receives HD-SDI signal over coaxial cable and transmits to HD Splitter or HD-DVR. (Recommended distance between SC-HRP0601D and HD Splitter/HDDVR is Max.20m) • Possible to supply power to the camera and the transmitter by using exclusive adaptor. • It receives Control DATA from RS-485 DATA input port and outputs through HD-SDI IN port. ④

③ ② ①

⑤

HD-SDI IN: Receives HD-SDI signals from the devices which outputs HD-SDI signal such as a transmitter (SC-HTP0601D), a repeater(SCHLR01D), HD-SDI camera. ② LED Indicator (Option) ①

-. HD-SDI Output Signal LED Indicator Description Green ON Normal operation for HD-SDI signal output - When the transmission distance is too long or the cables are not connected properly, there can find a loss of video even the LED indicator is on. -. Power check (Power LED) LED Indicator

Description • DIP_SW2 ON(VP): Normal operation for power Yellow ON • DIP_SW2 OFF(Without VP). • DIP_SW2 BLINK: Need to check the cable (cable shortYellow BLINK circuit/Disconnection) Please check the DIP_S/W configuration (“③” )for the power. - 4 -

Release Version 1.0

③

DIP SW

DIP SW: DC 48V Power supply Setup(With VP function / Without VP function) SW1 Not used Supplying 48V DC Power - When it is connected with SC-HTP0601D (Tx), SC-HLR01D (Repeater) properly, it supplies power to the units if they are connected correctly. ON - When the devices are connected correctly, the Yellow LED SW2 will turn on. But, if the devices are not connected correctly and/or there is any abnormal operation, the power LED will flicker. Not supplying DC 48V Power (Default mode) OFF - The Yellow LED is always on.

※ Warning: When you do not want to supply power (48VDC) to the camera using the SC-HRP0601D, please make sure to turn the DIP Switch OFF. Please turn the DIP Switch On after checking SC-HTP0601D(Down converter)/extra SC-HLR01D is connected properly. Otherwise, it may cause the camera damaged due to an overcurrent. (The Dip S/W of the product is set as an “OFF” mode as default value.) ④ DC IN & RS-485 PORT • DC INPUT: DC12V~48V Power input port[Input DC48V for power supply function.] • RS-485 DATA input port. ⑤ HD-SDI OUT: Outputs only HD-SDI signal over Coaxial cable. • Connect with the devices such as HD-SDI DVR or HD-SDI Splitter.

3-1-3. SC-HLR01D: Repeater (1 in 1 out) • Using this unit, you can extend the transmission distance of HD-SDI signals of HD cameras with HD-SDI output up to 200M. • Using SC-HTP0601D, (Extra)SC-HLR01D, SC-HRP0601D, you can supply power to the camera over the single coaxial cable. • Receiving RS-485 Control DATA and outputting through HD-SDI IN port.

③

④

② ①

⑤

- 5 -

Release Version 1.0

① HD-SDI IN • Connect with HD-SDI IN port in SC-HTP0601D with coaxial cable. • Power supply Output port when supplying power from the receiver. • It supplies power to the camera when the camera is connected with the SCHTP0601D. ② LED Indicator for Power & SDI input LED Indicator ON YELLOW BLINK GREEN

ON

Description • DIP_SW2 ON(VP): Normal operation for power • DIP_SW2 OFF(Without VP). • DIP_SW2 BLINK: Need to check the cable (cable shortcircuit/Disconnection) Normal Operation for HD-SDI signal input

③ DIP SW: DC 48V Power supply Setup(With VP function / Without VP function) SW1 (option)

DIP SW

ON OFF

ON SW2

OFF

Reclocker Bypass mode on. (Option). Reclocker Bypass mode off. (Option). Supplying 48V DC Power - When it is connected with SC-HTP0601D(Tx), SCHRP0601D(Rx), SC-HLR01D(Repeater) properly, it supplies power to the units if they are connected correctly. - When the devices are connected correctly, the Yellow LED will turn on. But, if the devices are not connected correctly and/or there is any abnormal operation, the power LED will flicker. Not supplying DC 48V Power (Default mode) • The Yellow LED is always on.

※ Reclocker Bypass Mode: as an optional feature, non-standard HD-SDI signal will be output , please do not use this mode in normal situation. ※ Warning: When you do not want to supply power (48VDC) to the camera using the SC-HLR01D, please make sure to turn the DIP Switch OFF. Please turn the DIP Switch On after checking SC-HTP0601D(Down converter)/extra SC-HLR01D is connected properly. Otherwise, it may cause the camera damaged due to an overcurrent. (The Dip S/W of the product is set as an “OFF” mode as default value.) ④ DC IN & RS-485 PORT • DC INPUT: DC12V~48V Power input port[Input DC48V for power supply function.] • RS-485 DATA input port. • Do not supply power through DC IN port if a repeater sends power over HDSDI OUT BNC. It may damage the devices. ⑤ HD-SDI OUT • Connect with HD-SDI IN port in SC-HRP0601D with coaxial cable. • Power supply input port when supplying power from the receiver. • Connect with the devices such as HD-SDI DVR or HD-SDI Splitter. - 6 -

Release Version 1.0

4. Connection Diagram 4.1 Example #1:

4-1-1. SC-HTP0601D (Tx) + SC-HRP0601D (Rx) • Connect HD Splitter (SC-HD04Q) with SC-HTP0601D. HD-SDI signals from SCHD04Q are transmitted to SC-HRP0601D through HTP0601D over coaxial cable (RG-6, Max.200m) and the signals are sent to HD-SDI Monitor(DVR). • The receiver (SC-HRP0601D) receives 48VDC and supplies power to SCHTP0601D (Transmitter). • Possible to control the HD Splitter using Control DATA received from the receiver through the transmitter. • Recommended Transmission distance between SC-HTP0601D (Transmitter) and a Splitter is Max. 10m. • Recommended Transmission distance between SC-HRP0601D (Receiver) and a Monitor/DVR is Max. 20m. (Transmission distance varies depending on the DVR/Monitor Spec or models)

4-1-2. SC-HTP0601D + SC-HLR01D [SC-HLR01D is used as a Receiver] • Possible to transmit HD-SDI signal from HD Splitter(SC-HD04Q) up to 200m by using SC-HTP0601D. • Supplying power (DC48V) to SC-HTP0601D by using SC-HLR01D (Repeater) • Possible to control the HD Splitter using Control DATA received from SCHLR01D (Repeater) through the transmitter. • Recommended Transmission distance between SC-HTP0601D (Transmitter) and a Splitter is Max. 10m. • Recommended Transmission distance between SC-HLR01D (Repeater) and a Monitor/DVR is Max. 200m. (Transmission distance varies depending on the DVR/Monitor Spec or models)

- 7 -

Release Version 1.0

4-1-3. SC-HTP0601D + SC-HLR01D (× 4) + SC-HRP0601D • Transmitting “HD-SDI video signal + Power + Control Data” over single coaxial cable up to 1km by using Max. 4 of SC-HLR01D (Repeater). • Recommended Transmission distance between SC-HTP0601D (Transmitter) and a Splitter is Max. 10m. • Recommended Transmission distance between SC-HRP0601D (Receiver) and a Monitor/DVR is Max. 20m. (Transmission distance varies depending on the DVR/Monitor Spec or models)

4-1-4. SC-HTP0601D + SC-HLR01D (× 4) [SC-HLR01D is used as a Receiver] • Transmitting “HD-SDI video signal + Power + Control Data” over single coaxial cable up to 1km by using Max. 4 of SC-HLR01D (Repeater). • Recommended Transmission distance between SC-HTP0601D (Transmitter) and a Splitter is Max. 10m. • Recommended Transmission distance between SC-HLR01D (Repeater) and a Monitor/DVR is Max. 200m. (Transmission distance varies depending on the DVR/Monitor Spec or models)

- 8 -

Release Version 1.0

4.2 Example #2:

4-2-1. SC-HTP0601D + SC-HRP0601D • Connect HD-SDI camera with SC-HTP0601D. HD-SDI signals from HD-SDI camera are transmitted to SC-HRP0601D through HTP0601D over coaxial cable (RG-6, Max.200m) and the signals are sent to HD-SDI Monitor (DVR). • The receiver (SC-HRP0601D) receives 48VDC and supplies power to SCHTP0601D (Transmitter). SC-HTP0601D converts DC48V to DC12V and supplies power to the camera. (Down-Converting) • Camera power consumption: DC12V, under 6W • Possible to control Camera OSD Menu using Control DATA received from the receiver through the transmitter. • The transmission distance varies depending on the Loop resistance value of coaxial cable when using power supply function. • Recommended Transmission distance between SC-HTP0601D (Transmitter) and the camera is Max. 10m. • Recommended Transmission distance between SC-HRP0601D (Receiver) and a Monitor/DVR is Max. 20m. (Transmission distance varies depending on the DVR/Monitor Spec or models)

- 9 -

Release Version 1.0

4-2-1. SC-HTP0601D + SC-HLR01D [SC-HLR01D is used as a Receiver] • Connect HD-SDI camera with SC-HTP0601D. HD-SDI signals from HD-SDI camera are transmitted to SC-HLR01D over coaxial cable (RG-6) and the signals are sent to HD-SDI Monitor (DVR). • The SC-HLR01D receives 48VDC and supplies power to SC-HTP0601D (Transmitter). SC-HTP0601D converts DC48V to DC12V and supplies power to the camera. (Down-Converting) • Camera power consumption: DC12V, under 6W • Possible to control Camera OSD Menu using Control DATA received from the receiver through the transmitter. • The transmission distance varies depending on the Loop resistance value of coaxial cable when using power supply function. • Recommended Transmission distance between SC-HTP0601D (Transmitter) and the camera is Max. 10m. • Recommended Transmission distance between SC-HLR01D (Repeater) and a Monitor/DVR is Max. 200m. (Transmission distance varies depending on the DVR/Monitor Spec or models)

4-2-3. SC-HTP0601D + SC-HLR01D (× 4) + SC-HRP0601D • Connect HD-SDI camera with SC-HTP0601D. HD-SDI signals from HD-SDI camera are transmitted to SC-HRP0601D through SC-HLR01D over coaxial cable (RG-6) and the signals are sent to HD-SDI Monitor (DVR). • The receiver (SC-HRP0601D) receives 48VDC and supplies power to SCHLR01D (Repeater) and SC-HTP0601D (Transmitter). SC-HTP0601D converts DC48V to DC12V and supplies power to the camera. (Down-Converting) • Possible to connect Max.4 of repeater (SC-HLR01D) when using the camera which consumes 6W DC12V. • Possible to control Camera OSD Menu using Control DATA received from the receiver through the transmitter. • The transmission distance varies depending on the Loop resistance value of coaxial cable when using power supply function. • Recommended Transmission distance between SC-HTP0601D (Transmitter) and the camera is Max. 10m. • Recommended Transmission distance between SC-HRP0601D (Receiver) and a Monitor/DVR is Max. 20m. (Transmission distance varies depending on the DVR/Monitor Spec or models) - 10 -

Release Version 1.0

4-2-3. SC-HTP0601D + SC-HLR01D (× 4) [SC-HLR01D is used as a Receiver] • Connect HD-SDI camera with SC-HTP0601D. HD-SDI signals from HD-SDI camera are transmitted to SC-HLR01D over coaxial cable (RG-6) and the signals are sent to HD-SDI Monitor (DVR). • The SC-HLR01D receives 48VDC and supplies power to SC-HTP0601D (Transmitter). SC-HTP0601D converts DC48V to DC12V and supplies power to the camera. (Down-Converting) • Possible to connect Max.4 of repeater (SC-HLR01D) when using the camera which consumes 6W DC12V. • Possible to control Camera OSD Menu using Control DATA received from the receiver through the transmitter. • The transmission distance varies depending on the Loop resistance value of coaxial cable when using power supply function. • Recommended Transmission distance between SC-HTP0601D (Transmitter) and the camera is Max. 10m. • Recommended Transmission distance between SC-HLR01D (Repeater) and a Monitor/DVR is Max. 200m. (Transmission distance varies depending on the DVR/Monitor Spec or models)

- 11 -

Release Version 1.0

5. Transmission Distance 5.1 Transmission Distance between two HD-SDI transmission solutions per coaxial cable type

Cable L-5CFB(Canare) 5C-HFBT(Kumkang) L-3C-2V(Canare) Belden 1694A 18AWG

Transmission Distance (m)

1.485Gb/s(HD)

2.97Gb/s(FULL HD)

200 200 90 200

120 120 50 120

 Please note the distance may reduce in the actual field due to any possible video loss. Therefore, we recommend you to connect the cable under 70% of the maximum distance stated above.  We recommend you to use BNC connectors with low connection resistance when connecting the coaxial cables.  Please be careful not to make deformation of the cable when wiring the cable.  Please avoid pulling the cable by force when wiring the cable.  Please avoid bending the coaxial cable too tightly when wiring the cable. It may make deformation of the cable.

6. SPECIFICATION 6-1. SC-HTP0601D (1CH Transmitter) Model # Video In/Out Input Power Power Consumption Max. Transmission distance Output Power SDI In/Out Connect Power Output Port Data Output

* SMPTE292M, SMPTE424M

SC-HTP0601D HD-SDI COAX DC 24V~48V (VP DC 48V IN DC 48V 25mA IN: Belden 1694A 10m(Full HD), RG-6 10m(HD) OUT: Belden 1694A 120m(Full HD), RG-6 200m(HD) DC 12V / 0.5A (6W) BNC-F (75Ω) 2Pin(Out of 4P) T. Block 2Pin(Out of 4P) T. Block

DATA comm.method

RS-485 / Half Duplex

BAUDRATE

2400 / 4800 / 9600 / 19200 / 38400 bps

SDI (Green) Power (Yellow) Temperature /Humidity Case body / Weight Dimension (mm)

On : Receiving On : Working / Flickering : Check -10℃ ~ +50℃ / 0 ~ 80％ Aluminum / 100g 76(W) X 42(H) X 25(D)mm

LED

- 12 -

Release Version 1.0

6-2. SC-HRP0601D (1CH receiver) Model # Video In/Out Input Power Power Consumption

Power Input

SC-HRP0601D HD-SDI DC 12V~48V, With VP function(DC 48V 1.04A) DC 48V 8mA IN: Belden 1694A 120m(Full HD), RG-6 200m(HD) OUT: Belden 1694A 20m(Full HD), RG-6 20m(HD) 270Mbps ~ 3Gbps BNC-F (75Ω) 1 2 DC OUTPUT OFF OFF ON Through 2Pin(Out of 4P) T. Block

Data Output

2Pin(Out of 4P) T. Block

Max. Transmission distance Bandwidth SDI In/Out Connect Port

* SMPTE292M, SMPTE424M

DIP SW

DATA comm.method

RS-485 / Half Duplex

BAUDRATE

2400 / 4800 / 9600 / 19200 / 38400 bps

SDI (Green) Power (Yellow) Temperature /Humidity Case body / Weight Dimension (mm)

On : Receiving On : Working / Flickering : Check -10℃ ~ +50℃ / 0 ~ 80％ Aluminum / 100g 76(W) X 42(H) X 24(D)mm

LED

6-3. SC-HLR01D (1CH repeater) Model # Video In/Out Input Power Power Consumption Max. Transmission distance Bandwidth HD-SDI In/Out Connect Port

* SMPTE292M, SMPTE424M

SC-HRP0601D

Power Input

HD-SDI DC 12V~48V, With VP function(DC 48V 1.04A) DC 48V 18mA Belden 1694A 120m(Full HD), RG-6 200m(HD) 270Mbps ~ 3Gbps BNC-F (75Ω) 1 Reclocker 2 DC OUTPUT OFF OFF OFF Bypass ON Through 2Pin(Out of 4P) T. Block

Data Input

2Pin(Out of 4P) T. Block

DIP SW

DATA comm.method

RS-485 / Half Duplex

BAUDRATE

2400 / 4800 / 9600 / 19200 / 38400 bps

SDI (Green) Power (Yellow) Temperature /Humidity Case body / Weight Dimension (mm)

On : Receiving On : Working / Flickering : Check -10℃ ~ +50℃ / 0 ~ 80％ Aluminum / 100g 76(W) X 42(H) X 24(D)mm

LED

- 13 -

Release Version 1.0

7. Warranty Certificate This product has passed thorough quality control and test, and if this gets broken during normal use, we provide 12 months warranty service. Model No. Serial No. Distributor Date you purchased Place you purchased Warranty Period Name Purchaser Address

One (1) year from the date of purchase

• Please • Please

check this warranty indication first. contact your distributor after checking out any defect in the products. • The standard for repairing, replacement or reimbursement follows Customer. • Warranty content any defect under normal use within the warranty service period we give you free repair service according to the warranty certificate. • We charge you with the fee of parts and service despite of free warranty service period. Any breakage made without care such as: - Breakage or trouble made by natural disaster. - Breakage or trouble made by breaking the product guide or manual. - Breakage or trouble made by wrong power voltage or frequency. - When you want to reassemble for full system or replace parts within warranty service period. - When unauthorized person modified or made damage on the product trying to repair it. • Please note that we don’t support the breakage after warranty service period is expired. If the customer wants to get it repaired, we charge them with the fee. • The specification is subject to change without prior notice for quality improvement.

- 14 -

Release Version 1.0

SeeEyes Co.,Ltd is the New Corporate Name of Samsung CCTV Service Co.,Ltd

SeeEyes Co.,Ltd

#502~506, Sunil Technopia, 440, Sangdaewon-Dong, Jungwon-Gu, Sungnam-Si, Gyeonggi-Do, Korea TEL : +82-(0)31-777-3508 FAX : +82-(0)31-777-3512 EMAIL : [email protected] http://www.sscctv.com/eng

- 15 -