HAZARDOUS LOCATION LINEAR FLUORESCENT LIGHTING
Explosion Proof Fluorescent Light Luminaire
Haz-Linear 7 Linear Fluorescent XFM Series Explosion Proof Fluorescent Light Luminaire The XFM Series is a must for any explosive atmosphere location! This product has five different hub entries at each end, enabling the installer to wire the luminaire at more desirable angles. Center ballast placement provides a more balanced luminaire for ease of installation and weight distribution.
Listings • UL 844 listed and labeled for hazardous locations • Class I, Division 1, Groups C and D; Class I, Division 2, Groups A, B, C and D • Class II, Divisions 1 and 2, Groups E, F and G • Class III • UL 1598A listed and labeled – marine type lighting luminaire – outside type (salt water) • UL 1598A testing equivalent to NEMA 4X requirements for hose-down and corrosion resistance • UL listed 1598 • UL listed and labeled for use inside paint spray booths and rooms
The XFM Series is available in 2' (2 lamp fixture only) and 4' lengths for 2, 3 and 4 lamp combinations in T5, T5HO, T8, and T8HO. Lamps included. Applications • Paint spray booths • Marine outdoor • Chemical plants • Wastewater treatment areas
• Oil drilling rigs, refineries • Grain elevators • Coal & dust storage
Features • Factory sealed, cast natural aluminum (U.S. Foundry) that is lightweight. • Ballast mounted in the center for better balance and low profile. • (5) 1/2" NPT hubs located at 0°, 45° and 90° angles. XFM Series
• One piece painted aluminum reflector • .189" wall borosilicate glass tubes
2 LAMP QTY
T8 LAMP TYPE T5** T8*† T5HO*† T8HO
2 (lamp) 3 (lamp) 4 (lamp)
2: (length) 4: (length)
4 LENGTH (ft)
UN VOLTAGE
OPTIONS
UN: Universal 120-277 50/60 Hz† 34: 347 volt (T5HO & T8 only)
* 5000K lamp standard for T5HO and T8 lamps ** 4100K lamp standard for T8HO and T5 lamps 3 and 4 lamp luminaires not available in 2 ft. length 3 lamp luminaires not available in T5 or T8HO *** 4' two lamp ONLY – 120V or 277V operation environment † Normally stocked Consult factory for non-standard luminaires.
Operating Temperature Codes Based on 40° C Ambient Luminaire XFM
Class I, DIV 1 Groups C & D T6 = 85° C
Class I, DIV 2 Groups A, B, C, D T4 = 135° C
Class II, DIV 1 Groups E, F, G T4 = 135° C
Simultaneous Presence Class I & II T4 = 135° C
• Also meets requirements for National Fire Protection Association (NFPA) Standard 33 and National Electrical Code (NEC) Article 516 • UL C approved and labeled Class I, Division 1, Groups C and D • NEMA 3, 4X, 7CD, 9EFG • Simultaneous presence Class I and Class II • Class I, Zone 1, Group II A • Class I, Zone 1, Group II B
EB: Emergency battery backup*** WG: Stainless steel guard P: Polycarbonate shield SR: P remium specular reflector (93% reflective specular reflector insert) MK: Wall/ceiling mount kit factory installation for the 4 lamp fixture (the XFM-4401 can be field installed on 2 & 3 lamp fixtures)
Lamp Wattages 2 ft.
WATTS
4 ft.
WATTS
T5 T5HO T8 T8HO
14 WATT 24 WATT 17 WATT N/A
T5 T5HO T8 T8HO
28 WATT 54 WATT 32 WATT 44 WATT
Explosion Proof Fluorescent Light Luminaire
Options
Stainless Steel Guards Description Stainless Steel Guard 2 lamp 2ft Stainless Steel Guard 2 lamp 4ft Stainless Steel Guard 3 lamp 4ft Stainless Steel Guard 4 lamp 4ft
Polycarbonate Shields (+/- 1/16" thickness) Catalog Number XFM-4466 XFM-4211 XFM-4557 (2) XFM-4211
Description Polycarbonate Shield 2 lamp 2ft Polycarbonate Shield 2 lamp 4ft Polycarbonate Shield 3 lamp 4ft Polycarbonate Shield 4 lamp 4ft
Catalog Number XFM-4464 XFM-4209 XFM-4497 (2) XFM-4209
Mounting Options Mounting Hanger Kits Description
Catalog Number
Wall & Ceiling Mounting Hanger Kit 2 or 3 lamp Wall & Ceiling Mounting Hanger Kit 4 lamp Drop Mounting Hanger Kit 2 or 3 lamp Drop Mounting Hanger Kit 4 lamp
XFM-4401 Option ‘MK’ - Factory Installed XFM-4405 XFM-4403
Wall/ceiling mount kit For 4 lamp P/N Option ‘MK’
Must be factory installed
Drop mount kit For 2 or 3 lamp P/N XFM-4405 P/N XFM-4403
Wall/ceiling mount kit For 2 or 3 lamp P/N XFM-4401
Emergency Battery Backup Ballast
Operation • Operates normally on 120V, 277V, 60 Hz or 220V 50 Hz • Luminaire switches to charging mode and resumes normal lighting once AC power is restored
UL 595, 844, 924, 1598
Features • When power fails the luminaire automatically switches to emergency mode. In emergency mode one lamp will provide safe egress lighting for at least 90 minutes.
• Only available as 4 ft. 2 lamp luminaire • Vented battery compartment • Explosion proof test switch and charging indicator light • Minimum starting temperature 0º C (32º F) • Maintenance free emergency ballast/battery pack/charger • 575 to 1200 lumen operation (depending on lamp type) • 3 year warranty
Explosion Proof Fluorescent Light Luminaire
Weights 2 Lamp 4 Ft. Fixture Fixture Weight: 40# Shipping Weight: 43#
2 Lamp 4 Ft. Fixture (EMERGENCY) Fixture Weight: 57# Shipping Weight: 60#
2L 2FT. Dimensions
45 HUB
7 1/4”
STD HUB
7 1/4”
9” 9”
90 HUB
48 7/8”
90 HUB
7 1/4”
3L 4FT. Dimensions
7 1/4” 7 1/4”
7 1/4”
13”
STD HUB
53 5/8”
53 5/8”
7 1/4”
45 HUB 45 HUB 45 HUB STD HUB STD HUB 45 HUB
13”
48 7/8”
7 1/4” 48 7/8” 13”
53 5/8”
4L 4FT. Dimensions
48 7/8”
18 3/4”
90 HUB
48 7/8” 53 5/8”
90 HUB
53 5/8” 48 7/8”
53 5/8” 48 7/8” 48 7/8”
53 5/8”
45 HUB
53 5/8”
45 HUB
7 1/4” 7 1/4”
STD HUB 45 HUB
7 1/4”
45 STDHUB 45HUB HUB
7 1/4”
7 1/4” 45 STDHUB HUB
STD HUB
45 HUB
48 7/8” 90 HUB
53 5/8”
13” 7 1/4”
45 HUB
48 7/8”
7 1/4” 7 1/4”
45 HUB
45 HUB
45 HUB 7 1/4”
STD
HUB 45 STD HUB HUB
18 3/4”
45STD HUB HUB 45HUB HUB 45
7 1/4”
STD HUB
45 HUB
45 HUB 90 HUB
18 3/4” 18 3/4”
45STD HUB HUB
7 1/4”
7 1/4”
53 5/8”
53 5/8”
53 5/8”
48 7/8”
45 HUB 45 HUB 7 1/4”
90 HUB
7 1/4”
7 1/4” 9”
STD HUB
4L 4FT. Dimensions 13” 90 HUB
45 HUB
7 1/4”
STD HUB 45 HUB 45 HUB
STD HUB
90 HUB
45 HUB 45 HUB
45 HUB
48 7/8”
90 HUB
4L 4FT. Dimensions
53 5/8”
STD HUB
53 5/8”
4L 4FT. Dimensions
7 1/4”
7 1/4” STD HUB
7 1/4”
48 7/8” 53 5/8” 48 7/8”
7 1/4” 3L 4FT. Dimensions
45 HUB HUB 45
45 HUB
90 HUB
7 1/4”
STD HUB
45 45 HUB HUB
45 HUB 53 5/8”
9” 7 1/4”
45 HUB 45 HUB
48 7/8” 53 5/8”
3L 4FT. Dimensions
7 1/4”
48 7/8”
FT. Dimensions
FT. Dimensions 4FT. Dimensions
45 HUB
7 1/4” 7 1/4”
FT. Dimensions
53 5/8” 48 7/8”
29 5/8”
45 HUB
53 5/8” 48 7/8”
48 7/8”
4L 4FT. Dimensions
HUB 45 HUB
7 1/4”
FT. Dimensions 4FT. Dimensions
HUB 4545HUB STD HUB STD
STD HUB
53 5/8”
2L 4FT. Dimensions
STD HUB
90 HUB
18 3/4”
53 5/8”
STD HUB 45 HUB
7 1/4”
3L 4FT. Dimensions
7 1/4”
STD 2L 4FT. Dimensions9” 90 HUB HUB 3L 4FT. Dimensions 7 1/4” 45 HUB 45 HUB
/4”
FT. Dimensions
48 7/8”
29 5/8”
7 1/4”
7 1/4”
48 7/8”
FT. Dimensions
45 HUB
9”
7 1/4”
53 5/8”
90 HUB
45 HUB
90 45 HUB HUB
7 1/4”
48 7/8”
45 HUB 48 7/8”
24 7/8”
90 HUB 9”
7 1/4”
48 7/8”
29 5/8”
9”
7 1/4”
FT. Dimensions
FT. Dimensions 4FT. Dimensions
2L 4FT. Dimensions
7 1/4”
45 HUB
24 7/8” 29 5/8”
29 5/8” 2L 4FT. Dimensions
90 HUB
9”
7 1/4”
7 1/4”
HUB 45 HUB
STD HUB
24 7/8” 29 5/8”
7 1/4” STD HUB
7 1/4”
24 7/8”
24 7/8”
FT. Dimensions
9”
45 HUB
7 1/4”
7 1/4”
29 5/8”
HUB 7 1/4” 45 HUB 7 1/4” 45 45HUB HUB STD HUB STD
2FT. Dimensions
7 1/4” 7 1/4”
FT. Dimensions 2L 2FT. Dimensions
9” 7 1/4”
45 HUB 45 HUB
24 29 7/8” 5/8”
7 1/4”
45 HUB
45 HUB 24 7/8” (Nominal) Dimensions STD
2L 2FT.4 Dimensions 4 Lamp Ft. Fixture Fixture Weight: 80# 2L 2FT. Dimensions Shipping Weight: 84# 90 HUB 2L 4FT. Dimensions
7 1/4”
STD HUB
FT. Dimensions
7 1/4”
90 HUB
7 1/4”
45 HUB
9”
7 1/4”
STD HUB
3 Lamp 4 Ft. Fixture Fixture Weight: 45# Shipping Weight: 52#
FT. Dimensions
45 HUB 45 HUB
24 7/8”
90 HUB
7 1/4”
2L 2FT. Dimensions
9”
7 1/4”
2 Lamp 2 Ft. Fixture Fixture Weight: 30# Shipping Weight: 33#
Vapor/Dust Proof Lighting
Haz-Linear 6 Linear Fluorescent DFP Series Front Access Industrial Vapor/Dust Proof Fluorescent Light Luminaire The DFP Series is a very versatile luminaire that is UL listed for hazardous environments (Class I, Division 2, Groups A, B, C and D and Class II, Division 2, Groups F and G). It is an ideal luminaire for industrial applications, wet locations and task lighting. Optional adjustable mounting brackets allow for precise aiming in multiple angles suitable for most applications. The DFP Series is available in 2, 3, 4, 5 and 6 lamp options, all using a 3/16" tempered glass lens with acrylic and polycarbonate optional lenses. With multiple hub locations, the DFP Series can meet most of your wiring needs. Lamps not included.
Listings • UL 844 listed U.S. and Canada • UL 1598 listed U.S. and Canada for marine locations • Class I, Division 2, Groups A, B, C, D • Class II, Division 2, Groups F, G
Applications
Features
• Chemical plants • Paper mills • Tunnels • Water treatment
T8 LAMP TYPE
DFP Series
• Front access luminaire for hazardous locations • Hinged front door frame • Hinged ballast tray • 3/16" tempered glass lens
• Seacoast areas • Prep, inspection, sanding • Machining areas • Coal & dust storage
T5 T8 T5HO T8HO
4 LAMP QTY 2 (lamp, 4') 3 (lamp, 4') 4 (lamp, 4') 5 (lamp, 4') 6 (lamp, 4')
PFT: 1/2" NPT hubs at top and side**
** 1/2” NPT standard *** UN2 T5HO only † For horizontal or ceiling mounted luminaire only
T-Ratings Model DFP-T5 DFP-T5HO DFP-T8HO DFP-T8*
• Zinc latches • Spring loaded lamp holders – standard • Sturdy 18 Ga. steel white powder coated housing
PFT HUB
UN VOLTAGE
UN: 120-277 50/60 Hz UN2: 347-480 50/60 Hz*** 34: 347 volt
• Class I, Zone 2, Groups II A & B • Class III • IP65, wet location • 40° C ambient rating • 55° C ambient rating for T8 (32 watt luminaires only)
OPTIONS
†
KH: Adjustable angle mount brackets CX: Cable mount (with 5' cable) PW: 3 wire whip SR: Specular reflector WG: Wire guard F: Fusing A: Acrylic lens P: Polycarbonate lens EM: E mergency battery backup ballast (consult factory)
Lamp Wattages Rated Ambient Deg. C 40° 40° 40° 55°
Supply Wiring Temperature 75° 75° 75° 75°
Class I, Div. 2 Operating Temperature Code T3C (160° C) T3C (160° C) T4A (120° C) T5 (100° C)
Class II, Div. 2 Operating Temperature Code T4A (120° C) T4A (120° C) T4A (120° C) T4A (120° C)
* Note: DFP-T8 with EM option (emergency battery backup) reduces rated ambient to 40°C
4 ft.
WATTS
T5 T5HO T8 T8HO
28 WATT 54 WATT 32 WATT 44 WATT
Vapor/Dust Proof Lighting
Dimensions (Nominal) 1/2 NPT BOTH ENDS
1/2 NPT HUBS
BRACKETS FOR OPTIONAL MOUNTING KITS
HINGED REFLECTOR
INTEGRATED ACCESS DOOR HINGE
Chain Hang Kit Part Number: DFP-CHAIN "A" ROTARY DRAW LATCHES
51 1/2"
HINGED DOOR FRAME
Cable Hang Kit Part Number: DFP-CABLE (zinc coated)
53 1/8" QTY 2 cables with toggle ends
and QTY 2 self locking gripples "A": chains 52 1/4” between
5 5/16”
2 LAMP: 12 3/16" 3 & 4 LAMP: 16 3/16" 5 & 6 LAMP: 20 11/16"
Mounting Guide
Cable Hang Kit Part Number: DFP-CABLE (zinc coated)
QTY 2 cables with toggle ends and Hang QTY 2Kitself locking gripples Cable Part Number: DFP-CABLE 52 1/4” between chains (zinc coated) QTY 2 cables with toggle ends and QTY 2 self locking gripples
52 1/4” between chains
Pendant Style Mounting (standard) NOTE: Conduit provided by others Fixture suspended with 1/2” electrical conduit using top hubs on fixture at both ends.
45” between conduit
Adjustable Surface Mounting Bracket Kit Part Number: DFP-SURFACE (galvanized) DFP-SURFACESS (stainless steel) Bracket attachment point for optional mounting methods
Adjustable Surface Mounting Bracket Kit Part Number: DFP-SURFACE (galvanized)
conduit
nduit
Please ask your Thomas & Betts sales representative for a complete catalog of quality Thomas & Betts electrical DFP-SURFACESS (stainlessForsteel) products or visit us at www.tnb.com. For customer service, call 1-800-816-7809. technical questions, call 1-888-862-3289.Bracket attachment point for optional mounting methods
Adjustable Surface Mounting Bracket Kit
© 2013 Thomas & Part Betts Corporation. rights reserved. Printed in the U.S.A. Number: All DFP-SURFACE (galvanized) 08/13/2.5M GM7236
DFP-SURFACESS (stainless steel) Bracket attachment point for optional mounting methods
Chain Hang Kit Part Number: DFP-CHAIN
Thomas & Betts Corporation Electrical Division 8155 T&B Boulevard Memphis, TN 38125 901-252-5000 www.tnb.com
45” between conduit