Sikom GACII v1.1
El-nummer: 64 309 33
GSM Alarm Controller II
Instructions - Remote control of heat Possible to control up to 3 different outputs
- Alarm GSM Alarm Controller II contains 4 inputs, and can send SMS messages to 4 different numbers when an alarm situation occurs
- Temperature Temperature measurements between -29ºC and +49ºC. Sends a SMS message when limits are reached. Can control 1 output based on temperature
- Based on control by the GSM network Any SIM card can be used
- Can be controlled by any phone with # and * keys. - Choose your own personal code - Status messages SMS messages with complete status of the inputs, outputs, power and temperature.
www.sikom.no
-1-
Sikom GACII v1.1
El-nummer: 64 309 33
Table of contents Page 1
Installation 1.1 1.2 1.3 1.4 1.5
2
Information about GSM remote control How to remote control by phone
4 5
User menu 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12
4
3 3 4 4 4
Remote control and user functions 2.1 2.2
3
Preparation of SIM card Mounting SIM card Power up Signal strength Local control
Main menu Graphical overview Activate multi SMS transmission Switch control Programming access code Programming SMS numbers Temperature control Alarm functions Status messages Temperature surveillance Limits for temperature surveillance Other messages
6 7 8 8 8 9 10 11 12 13 13 14
Needs and useful information 4.1 4.2 4.3 4.4 4.5 4.6
www.sikom.no
GSM coverage Control of heat DTMF Battery and power loss Smoke detectors Technical information
-2-
15 15 15 15 16 16
Sikom GACII v1.1
1
El-nummer: 64 309 33
Installation The following must be done with GSM Alarm Controller II before use:
1.1
Preparation of SIM-card: GSM Alarm Controller II needs a SIM-card to work. A SIM-card is included from Sikom, but not activated. To activate this, the information on the included form must be completed and returned to Sikom. Fax nr. 74085970. Other SIM-cards from different GSM-providers can be used. GSM Alarm Controller II needs a SIM card with the PIN-code deactivated. This can be done with an ordinary GSM-Phone. Put the SIM-card in a regular phone, and follow the phones manual to deactivate the PIN-code. (This is not necessary for the SIM-card provided by Sikom)
1.2: Mounting SIM-card: Be sure the GSM Alarm Controller II is turned off. (Should always be turned off when something is done with the SIMcard). Remove the front cover on GSM Alarm Controller II as shown on figure 1. Install the SIM-card as shown. The golden contact points faced down.
www.sikom.no
-3-
Sikom GACII v1.1
El-nummer: 64 309 33
If something is wrong with the SIM card or insertion of this, the yellow LED will start flashing 3 times. Check the deactivation of the PIN code of your SIM card and the lock of the SIM card container, and try again.
1.3 Starting up When all the connections are made, and SIM card inserted, the GSM Alarm Controller II can be turned on. GSM Alarm Controller II will use about 1 minute for self test and registration on the GSM network.
1.4 Signal strength The light on the keyboard will show the signal strength on the GSM network. Press * (star) on keyboard. The light will blink in 3 ways: 1. Blinks green Good signal. 2. blinks Red/green equally Not so good signal. (-93->dB) 3. Blinks Red Bad or no signal. (-103-> dB) If point 2 or 3 occurs, the antenna should be moved for better coverage. 1.5
Local control/front panel All the outputs can be locally controlled by the switches on top of the GSM Alarm Controller II. Push and keep the button depressed for some seconds until the light changes. The output is turned on when the light is green. The alarm can be locally turned on and off by pressing your code on the keyboard. When the alarm is activated, you have about 10 seconds to enter your code on the keyboard before the alarm responds.
2
Remote control and user functions
2.1 Information about GSM remote control The GSM Alarm Controller II can be controlled by any phone which contains the hash and star keys. The control is done by the phones DTMF tones. These are the tones you can hear when you press any button on the phone during a call. On some phones, these tones need to be activated. Check your phone manual.
www.sikom.no
-4-
Sikom GACII v1.1
El-nummer: 64 309 33
When you call the GSM Alarm Controller II, you will get 4 tones: 1 Answer tone - Contains two Ok-tones 2 Approved - Contains 1 single tone 3 OK tone - Contains a low high double tone 4 Error tone - Contains three short beeps If there's more than 30 seconds between each key press, the GSM Alarm Controller will automatically hang up. The GSM Alarm Controller II is protected by a personal code. This code must always be entered at first when calling the unit. If the wrong code is entered, the GSM Alarm Controller II will hang up. To change this code, see point 3.5. The factory code is 1234. When you have dialled the GSM Alarm Controller and logged in with the correct personal code, the main menu is always active. If you press # the GSM Alarm Controller will automatically hang on when this menu is active. In the submenus, # has the following meaning: # will take you back from a submenu to the main menu if you accidentally press a wrong button. Then you can give another command from the main menu. After 30 seconds of inactivity, the GSM Alarm Controller automatically hangs up. 1 means ON and 0 means OFF. Hyphen (””) covering the number in the menus means the number should be pressed on your phones keypad.
2.2 How to remote control by phone 1. Dial GSM Alarm Controller. Wait for answer! 2. Press personal code. Wait for acknowledgement! 3. You are now in the main menu, and can choose between menus 1-9.
www.sikom.no
-5-
Sikom GACII v1.1
3
El-nummer: 64 309 33
User menu When the number to the GSM Alarm Controller II is dialed and the personal code entered, the unit can be controlled by the main menu and the sub menus as explained.
3.1 Main menu Main menu: - Menu 1: - Menu 2: - Menu 3: - Menu 4: - Menu 5: - Menu 6: - Menu 7: - Menu 8: - Menu 9:
Multi sending SMS Output control Change personal code Programming SMS numbers Temperature control Alarm Status message Temperature surveillance Limits for temperature surveillance
Each of these main menus has sub menus as shown on the pictures later. Several commands can be executed during the same call. The GSM Alarm Controller II will automatically return to the main menu after execution of a command. In the explanation to the menus, the numbers which are to be pressed on your phone encapsulated in hyphen like this ”2”. The navigation through the menus is done the following way: Chose the menu to enter. Choose sub menu, and then function. Example: Turn on output 2; press ”2” then ”2” followed by ”1” Shown graphically in the figure.
www.sikom.no
-6-
Sikom GACII v1.1
El-nummer: 64 309 33
3.2 Graphical overview This figure shows the menu structure of the GSM Alarm Controller II. The boxes to the right shows the menus in the main menu. The center contains the sub menu, and the left boxes shows your choices.
www.sikom.no
-7-
Sikom GACII v1.1
El-nummer: 64 309 33
3.3 Menu 1 Activate multi SMS transmission GSM Alarm Controller II can send alarm messages to 4 different numbers/receivers. Also called multi sending. These 4 numbers are stored in different positions by menu 4. To activate the different numbers, menu 1 must be used. The status messages are only sent to number 1. Number 1 can not be deactivated. - Press ”1” - Press the position number of the SMS number you want to activate/deactivate. ”2”, ”3” or ”4” - ”1” to activate, ”0” to deactivate You are now returning to the main menu. Example: ”131” activate position number 3, ”130” deactivate.
3.4 Menu 2 Output control The relays can be controlled manually on the top-card of the GSM Alarm Controller II, or by phone as explained below. 1. Press “2” (after calling GSM Alarm Controller and logging on) You are now in submenu 2, relay-control. 2. Press relay number - followed by “1” for ON or “0” for OFF Command: “11” “21” “31”
Function: Command: turn relay 1 on turn relay 2 on turn relay 3 on
Function: “10” “20” “30”
turn relay 1 off turn relay 2 off turn relay 3 off
You will now get the OK tone which indicates function executed. To turn on/off more relays, you can now go back into menu 2, and use another combination of the above commands.
3.5 Menu 3 Change personal code Change the personal code by calling the GSM Alarm Controller II. It is the same code which activates or deactivates the alarm functions. 1. Press “3” . 2. Press new (self chosen) access code (4 digits) 3. Wait for approved 4. Press new access code once more (4 digits) 5. Wait for OK tone You are now in the main menu!
www.sikom.no
-8-
Sikom GACII v1.1
El-nummer: 64 309 33
Reset the personal code: GSM Alarm Controller is delivered with code 1234. If you wish to reset back to this code, do the following: Hold button 3 on the GSM Alarm Controller II Press and release Reset Keep holding button 3 for at least 5 seconds. If the reset is successful, 3 blinks will be shown in the reset indicator.
Reset of the personal code can only be done as shown.
3.6 Menu 4 Programming SMS numbers In order for the GSM Alarm Controller to send a SMS message, the number to the recipient must be programmed. 4 different numbers can be programmed. The status message can only be sent to number 1. Remember to activate multi sending by using menu 1 if desired. - Press ”4”. - Press the position of the number, ”1”,”2”,”3” or ”4”. - Press the wanted phone/fax number - End with star ”*”, wait for OK-tone. You are now in the main menu! If more numbers are to be stored, repeat the above procedure. Example: Store number on position 3: ”4 3 92239906 *” You can verify the numbers entered by requesting status message number 3. (”7 - 3”). The numbers entered will be listed here. If the GSM Alarm Controller II should send messages to a phone/fax abroad, you need to press star “*” followed by country code and phone number. The star will represent the + sign. (Example: Sweden: “4 3 *4692151515*”)
www.sikom.no
-9-
Sikom GACII v1.1
El-nummer: 64 309 33
3.7 Menu 5 Temperature control When temperature control is activated, relay/output 3 will turn itself on when the temperature reaches 4 degrees and below. It will turn itself of when the temperature reaches 6 and above. This will ensure constant temperature between about 4 and 6 degrees Celsius given output 3 controls a heat element which is capable of heating the entire room. If you turn on output 3 by using menu 2, it will override the temperature control. -
Press ”5”. Press ”1” for ON or ”0” for OFF, wait for OK tone.
You are now in the main menu! Example: ”51” Turn ON, ”50” Turn off. If a higher temperature than 4-6 degrees is wanted, the relay can be turned on by using menu 2. The temperature control is still active, and will resume operation when relay 3 is turned off by menu 2 or local, until it is turned off by “50”
www.sikom.no
- 10 -
Sikom GACII v1.1
El-nummer: 64 309 33
3.8 Menu 6 Alarm Activation and deactivation of the alarm. If the unit is to send SMS messages the alarm sensing must be turned on. The zones can be turned individually on and off, but the master must be turned on to get messages. - Press ”6”. - Press ”9” to activate master sensing or ”0” to deactivate. You are now in the main menu! Example: "69" activate, ”60” deactivate.
If the alarm is triggered, there will be a 10 sec delay where you can enter the personal code on the keyboard to deactivate. If the alarm is triggered, no SMS messages will be generated for the corresponding input the first hour. After 1 hour or turning the alarm off and on again manually, will reset the input, and new messages can be transmitted. Turning on and off alarm zones. You can turn on and off the 4 different inputs or zones as required. If one zone is turned off, no messages will be generated for that input. This means you can have smoke detectors active while burglary is turned off. Remember to turn on the alarm sensing by using menu 69. The zones are activated and deactivated in the following way: - Press ”6”. - Press zone ”1”, ”2”, ”3” or ”4”. - Press ”1” to activate, ”0” to deactivate, wait for OK-tone. You are now in the main menu! Example: "621" activate zone 2, ”620” deactivate.
www.sikom.no
- 11 -
Sikom GACII v1.1
El-nummer: 64 309 33
3.9 Menu 7 Status message Sends a status message to the number stored in position 1 GSM Alarm Controller II can send 3 different status messages: Message 1 shows temperature, status of temperature surveillance, relays/outputs, limits and temperature control. Message 2 shows the alarm status, alarm zones and Multi-SMS. Message 3 shows the status of the power and the 4 different numbers stored in position 1-4. Ask for status message: - Press ”7” followed by message number ”1”, ”2” or ”3”. - Several beeps will be heard indicating status message being transmitted. - Wait for OK-tone. You are now in the main menu! Explanation to message 1: Temp: +18 o Shows the temperature where the sensor is mounted. TempCont: Off o Shows if the temperature control is on or off. Relay 1:On 2:Off 3:On o Shows if the outputs are on or off. Limits: Off Hi: +25 Lo: +05 o Shows if temperature surveillance is on or off. Shows the low and high limits. Explanation to message 2: Alarm: Off o Shows if the master alarm is turned on or off. Zone 1:On 2: Off 3:On 4:Off o Shows if the 4 zones are on or off. Remember that master alarm must be activated for the zones to work. Number: 2:On 3:Off 4:On o Shows if the alarm messages should be transmitted to the numbers in position 2 to 4. Explanation to message 3: Power ok! o Power to the unit is ok.
www.sikom.no
- 12 -
Sikom GACII v1.1
El-nummer: 64 309 33
Power lost! o Power to the unit is not ok. Num1:95012582 Num2:95458721 Num3:41854762 Num4:22846852 Shows the 4 different numbers stored in position 1 to 4.
o
3.10 Menu 8 Temperature surveillance Turns temperature surveillance on or off. If the limits are reached, this function will send a status message indicating the temperature. See pt. 3.11. -
Press ”8”. Press ”1” to activate or ”0” to deactivate Wait for OK-tone.
You are now in the main menu! Example: ”81” Turns on, ”80” Turns off.
3.11 Menu 9 Limits An upper and lower limit can be programmed. If activated by menu 8, these limits will, when reached, be reported by a SMS message. Note: Once the limits are reached, only one message will be transmitted, and the surveillance will be turned off. You have to manually turn these on again by using menu 8. This must be done again when the temperature is within the limits, or the message will be generated again. Temperature below 0 degrees must be preceded by a star (*). Positive temperature must be preceded by zero (0) Example: -20ºC and +20ºC will be entered as: ”*20” and ”020”. Remember always two digits for temperature: -2ºC will be entered as *02 and +2ºC will be entered as 002. The lowest temperature is -29ºC and the highest is +49ºC. -
-
www.sikom.no
If you enter -30ºC as the lowest and for example -5ºC as the highest, only -5ºC will be reported, as the GAC II will newer reach -30ºC. If +3ºC and 50ºC is entered, only the lowest will be reported.
- 13 -
Sikom GACII v1.1
-
El-nummer: 64 309 33
If a limit between -29ºC and +49ºC is entered for both high and low, the first limit broken will be reported.
How to program the limits: - Press ”9”. - Press the lower limit 3 digits and wait for approved tone. - Press the upper limit 3 digits and wait for OK tone. You are now in the main menu! Remember to activate the surveillance by using menu 8.
3.12 Other messages: Alarm 1 active! o Shows which input is activated. The master alarm and corresponding zone must be on. Power lost! o The power has been away for about 10 minutes. The output relays will not work if power to the unit is lost. Power ok! o The power is back. Output relays will be in the same position as they were before. All functions of the GSM Alarm Controller II will survive a power loss.
www.sikom.no
- 14 -
Sikom GACII v1.1
4
El-nummer: 64 309 33
Needs and useful information
4.1 GSM coverage To make sure the GSM Alarm Controller works satisfying, the coverage of the GSM network is essential. The SMS-message will not be transmitted if you have bad coverage. The GSM Alarm Controller will try to resend the message in case of errors until the message is sent. The moment the message is sent to the network, it's the net operator’s responsibility to make sure it reaches its destination. The SMS message will not reach the destination if there's an error with the network or other cases the net operator is responsible for. If the GSM network is heavily loaded, several minutes, worst case hours can pass before the message reach destination. Date and time is however noted on the SMSmessage. If your SIM card is based on a pay before you use service, always make sure the card is active and not out of money. This will make sure that the GSM Alarm Controller is able to generate SMS-messages When calling the GSM Alarm Controller, make sure that DTMFtones (Dual Tone Multi Frequency) is activated from the calling phone. The use of GSM Alarm Controller is based on these tones. This especially applies to ISDN phones, and other generic centrals. See your phone manual to check this. Older devices will work as long as they have * and # .
4.2 Control of heat If the GSM Alarm Controller II is used to control heaters, make sure the heater has enough capacity to warm the actual room.
4.3 DTMF When calling the GSM Alarm Controller, make sure that DTMFtones (Dual Tone Multi Frequency) is activated from the calling phone. The use of GSM Alarm Controller is based on these tones. This especially applies to ISDN phones, and other generic centrals. See your phone manual to check this. Older devices will work as long as they have * and # .
4.4 Battery The GSM Alarm Controller II has a 12 volt battery rated 700mAh. This battery is constantly being charged, and will when power is lost supply the unit with enough power to last between 10-15 hours depending on GSM coverage and connections made to the unit.
www.sikom.no
- 15 -
Sikom GACII v1.1
El-nummer: 64 309 33
If the power is lost, the relays will be turned off to save power. The lights indicating on or off on the top of GAC II will still show the current status of the relays. The unit will send a message after 10 minutes of power loss. The GSM Alarm Controller II will turn itself off if the internal battery is drained, but as soon as the power gets back, the functions are restored to the state before power loss. The battery is supposed to have a lifetime of about 2-3 years, and should be replaced by qualified personal if the capacity is to be sustained.
4.5 Smoke detectors The smoke detectors have internal sirens which will work independently of the GSM Alarm Controller II.
5 Technical specifications Model: Operating Voltage: Battery: Current consumption:
GSM Alarm Controller 230V 50Hz AC or 12-15 V DC 12V 700 mAh NiCd Memory less 40mA-Standby without detectors or relays activated. Each relay uses about 30mA
Standby time power loss: Max standby time best case:15 hours Max standby time worst case:6 hours
(Max)
Operating Temperature: Storage Temperature:
-20ºC to 50ºC -40ºC to 70ºC
Dimensions GSM: Weight:
158 X 90 X 58 mm 690 g
For alarm-connections: Alarm operating voltage: 12-15 V DC Alarm current consumption: Connection max 60 mA on the 4 inputs S1-S4 Termination: 10 Kohm from S input through detector to GND (earth)
www.sikom.no
- 16 -
