GENUINE PARTS

INSTALLATION INSTRUCTIONS 1. 2. 3.

DESCRIPTION: APPLICATION: PART NUMBER:

4.

KIT CONTENTS:

Item A B C D E F G

5.

QTY 1 1 1 1 1 1 1

Description Control module Encoder and harness assembly Foot well lights and harness assembly Cup holder lights and harness assembly Harness Vehicle interface Control Knob Kit contents list at end of installation instructions

Service Part Number 999F3 AW004 999F3 AW006 999F3 AW001 999F3 AW003 999F3 AW005 999F3 AW002

TOOLS REQUIRED ● ● ● ● ●

6.

Accent light Kit Versa (2010) 999F3 AW000 - Universal Accent Lighting Kit.

Trim stick 10mm, 11mm & 13mm sockets #2 Philips screwdriver Protective cloth Metric ruler

● ● ● ● ●

Ratchet and 6" extension 5/16", 3/16" and 9/32" drill bits, drill stop. T-20 Torx bit Scissors Electrical tape, masking tape.

PRE-INSTALLATION CAUTION/NOTES ● ● ● ●

Dealer installation recommended. Instructions may refer to Service Manual Installation may require special tools This part is to be installed at a surface temperature no warmer than 65-100ºF Remove and prepare templates located at the end of Installation Instructions

CAUTION ● This accessory must only be installed as specified in these instructions. ● Ensure at all times that parts are securely fitted and will not compromise the safe function of vehicle systems.

Page 1 of 17

999F3 4W010II - Rev. 07.01.2010

INSTALLATION INSTRUCTIONS - Accent Lighting Kit 7. GENERAL SYSTEM OVERVIEW

Fit-up 2 action points: Prepare exploded view drawing of vehicle interior with fixings detail (clip, screw, bolt etc).

8. CRITICAL STEPS: The following steps are critical and must be performed EXACTLY as specified to ensure proper installation ● ● ●

Location of the lights must be followed exactly as described in this instruction Posi-Tap ™ instructions must be specifically followed as described. Cables must be properly secured to prevent rattling and/or snagging on any moving parts or limbs e.g. cup holder harness running through centre console close to handbrake

Page 2 of 17

999F3 4W010II - Rev. 07.01.2010

INSTALLATION INSTRUCTIONS - Accent Lighting Kit 9. VEHICLE PREPARATION 1) a)

Vehicle Preparation Reecord customer radio presents

1

2

3

4

5

A B C b) c) d)

Apply parking brake Turn off the ignition Disconnect battery negative terminal

NOTE: USE CAUTION WHEN REMOVING/RE-INSTALLING TRIM COMPONENTS TO AVOID DAMAGE, SCRATCHES, BREAKING OF CLIPS AND/OR INTERIOR TRIM PANELS. MOVE ALL TRIM COMPONENTS TO A PROTECTED AREA. 2)

Remove the following interior parts as shown. Refer to the vehicle service manual.

a) Console mask b) Console mask cover Note: For M/T remove shift knob c) Console rear finisher d) LH and RH instrument lower covers

e) f) g) h) i)

Shifter finisher Console body ass'y Center console Fuse block lid Side mask LH

Page 3 of 17

j) k) l) m)

Instrument side finisher Instrument lower finisher Glove box assembly Rear cup holder. holder

999F3 4W010II - Rev. 07.01.2010

INSTALLATION INSTRUCTIONS - Accent Lighting Kit 10. LIGHT STICK PREPARATION

Before

LED side

1)

Prepare driver side light stick.

a)

Clean mounting area with alcohol wipe.

b)

Fix (1) 12.5 x 19 x 0.7mm adhesive pad with edge aligned to position 3 as

Loop Fig. 1

After

LED side

shown- on LED side. c)

Fix (1) 12.5 x 19 x 0.7mm adhesive pad with edge aligned to position 10 as shown - on LED side.

3

3

10

3

10 10

Before

Fig. 1 (cont'd)

LED side

2)

Prepare passenger side light stick.

a)

Clean mounting area with alcohol wipe.

b)

Fix (1) 12.5 x 19 x 0.7mm adhesive pad with edge aligned to position 1 as

Fig. 2

LED side

After

shown - on LED side. c) Fix (1) 12.5 x 19 x 0.7mm adhesive pad with edge aligned to position 11.5 as shown - on LED side.

11.5

0.5

1

Fig. 2 (cont'd)

Page 4 of 17

999F3 4W010II - Rev. 07.01.2010

INSTALLATION INSTRUCTIONS - Accent Lighting Kit 11. INSTALLATION PROCEDURE: 1)

Remove (4) Philips screws attaching Cupholder.

CAUTION ● Use only a 9/32" drill to avoid damage to Cupholder. Holes larger than 9/32" will not retain LEDs. ● Use a drill stop to avoid damage to the Cupholder.

Page 5 of 17

2)

Prepare Cupholder for LEDs.

a) b) c))

Tape LED template (A) to cupholder. Mark and drill (2) 9/32" holes. Snap LED Lenses and p in Cupholder p lens retainers.

3)

Prepare Cupholder for Encoder.

a) b)

Tape Encoder template (B) to cupholder. Mark and drill (1) 5/16" hole.

999F3 4W010II - Rev. 07.01.2010

INSTALLATION INSTRUCTIONS - Accent Lighting Kit 11. INSTALLATION PROCEDURE: Fig. 4

4) Install Cupholder LEDs and Encoder. a) Clean mouting area with alcohol wipe. b) Peel double-sided tape liner and place each Cupholder light assembly as shown. c) Secure cable with foam tape as shown.

Fig. 4 (cont'd)

Fig. 5 50mm

5) Prepare Instrument Lower Finisher. a) Align long bracket to finisher rib and bracket hold to finisher edge as shown. Mark the hole. b) Align medium bracket to finisher rib and flater finisher surface before break. Mark the hole. c) Drill (2) 3/16" holes at marked locations.

15mm

5mm

d) Install Encoder, 11mm Lock Nut and Knob. e) Route LED wires next to Encoder wires and install 4" cable tie. f) Reinstall Cupholder and (4) Phillips screws to center console.

*

5mm

Fig. 6

(OBD Connector)

6)

Install the brackets.

a) b)

Clean mounting area with alcohol wipe. Peel off double-sided tape liner from long and medium brackets. Install brackets to lower finisher with holes aligned. Install (2) Philips screws and U-nuts from kit.

d) e)

Page 6 of 17

999F3 4W010II - Rev. 07.01.2010

INSTALLATION INSTRUCTIONS - Accent Lighting Kit 11. INSTALLATION PROCEDURE: 7)

Install driver side light assembly.

a) b) c)

Clean mounting area with alcohol wipe. Peel tabs away from adhesive tape. Press assembly onto bracket with tape centered. Install (4) 4" cable ties around wire, light assembly and brackets. Trim excess cable tie.

d)

8)

Reinstall Instrument lower finisher.

a) b)

Reinstall OBD connector to finisher. Add 4" cable tie to secure wire loop on light stick to OBD harness as shown. Reinstall Instrument lower finisher.

c)

9)

Page 7 of 17

Route Passenger side light assembly behind IP brace as shown.

999F3 4W010II - Rev. 07.01.2010

INSTALLATION INSTRUCTIONS - Accent Lighting Kit 11. INSTALLATION PROCEDURE:

10) Install Passenger side brackets. (with glove box removed) a) b)

Remove (2) Phillips IP screws. Install the (2) short brackets.

11) Mount passenger side light assembly. a) b) c)

d)

Clean bracket surface with alcohol wipe. Peel tabs away from adhesive tape. Press light assembly onto brackets with bracket edges aligned to tape edges. Install (2) 4" cable ties through bracket holes, around wire, light assembly and brackets.

NOTE: ENSURE LEDs ARE NOT OBSCURED BY CABLES TIES, WIRING, BRACKETS etc.

Page 8 of 17

999F3 4W010II - Rev. 07.01.2010

INSTALLATION INSTRUCTIONS - Accent Lighting Kit 12.

PosiTap installation. Fig. 12

12) Tap vehicle wire.

b)

a) b) c)

a)

Remove cap (slot side) from tap body. Slide cap around vehicle wire. Tighten the tap TIGHT with finger pressure.

NOTE: Do not re-use the tap for subsequent reinstallation. Figures are not to scale. Fig. 13

13) Inspect the tap to ensure correct installation.

NOTE: Avoid putting pressure on the vehicle wire and tap for the remainder of the installation.

i. Straight and evenly spaced all the way around ii. Tight and minimize gap (wire jacket should be crushed) Fig. 14 e) Insert wire to here c)

a) d) f) Tighten

Fig. 15

14) Tap accessory wire. a) b) c))

Remove tap (non-pierce) side from tap. Remove the protective stub from the wire. Insert I t wire i through th h the th non-pierce i side id opening. i

d) e)

Spread the individual strands into fan shape. Insert wire into the tap body and ensure that it is all the way in.

f)

Tighten the tap TIGHT with finger pressure.

15) Confirm the tapped accessory wire. a) b)

Inspect the tap to ensure correct installation. Test the signal to ensure that it is working properly.

i. Straight and evenly spaced all around ii. Tight and no gap and test the signal

Page 9 of 17

999F3 4W010II - Rev. 07.01.2010

INSTALLATION INSTRUCTIONS - Accent Lighting Kit 11. INSTALLATION PROCEDURE: Fig. 16

Vehicle Harness

...

b)

a)

16) Secure the tap. a)

Secure the tapped wire on the non-pierce side to the body of the tap with electrical tape (≥ 2 revolutions).

b)

Secure the body to harness where vehicle wire is being tapped with electrical tape (≥ 2 revolutions).

Accessory

CAUTION ● Color(s) given in illustration(s) are for reference only. Use location(s) where color deviates. ● If a vehicle wire is being used by another accessory and a posi-Tap is present, tap the accessory wire NOT the vehicle wire. NOTE: BCM is located behind glove box. Fig. 17 Fig 17.

17) Connect Accent Lighting ground. a)

Remove bolt from left BCM bracket.

b)

Install Accent Lighting ground eyelet under screw and reinstall.

18) Tap Accessory Green wire to Light Green wire, Cavity 57 of Black BCM connector M20. See steps 14-18 for wire tap installation instruictions. Fig 18.

Page 10 of 17

999F3 4W010II - Rev. 07.01.2010

INSTALLATION INSTRUCTIONS - Accent Lighting Kit 11. INSTALLATION PROCEDURE: 19) Tap Accessory Brown wire to the Brown wire, Cavity 63 of BCM connector M20. See steps 14-18 for wire tap installation instructions.

20)

Tap Accessory Blue wire to the Dark Blue wire, Cavity 11 of BCM connector M18. See steps 14-18 for wire tap installation instructions.

Page 11 of 17

999F3 4W010II - Rev. 07.01.2010

INSTALLATION INSTRUCTIONS - Accent Lighting Kit 11. INSTALLATION PROCEDURE:

21)

Route Power cable.

a)

Route Power cable and excess wire along existing IP harness as shown.

b) c)

Install (2) 4" cable ties as shown. Route Power cable behind center IP brace following light stick wire routing.

22)

Prepare Module

a) b) c)

Connect Power Cable to Module. Connect footwell light wiring to Module. Peel tape liner from foam pad and stick pad to Module.

23)

Partially install center console and connector encoder and cup holder light sticks.

CAUTION ● Only use your fingers to release Module connector. ● Prying on release tab with any tool may damage the tab.

24)

Mount Module.

a) b) c)

Peel tape liner from foam pad on Module. Adhere module to Driver Side IP brace. Use (2) 11" cable ties to secure Module to IP brace.

d)

Use 4" cable tie to secure power and footwell light wiring to IP brace.

Page 12 of 17

999F3 4W010II - Rev. 07.01.2010

INSTALLATION INSTRUCTIONS - Accent Lighting Kit 11. INSTALLATION PROCEDURE: 25)

Connect console accessory wiring.

a)

Place console in vehicle so console accessory wiring can reach Module.

b)

Route console accessory wires over IP brace.

c)

Connect console accessory wiring to module.

d)

Use 11" cable tie to secure remaining wiring under console.

26)

Verify that the system is functional.

27)

Re-assemble vehicle in reverse order.

CAUTION ● Use caution when removing/re-installing trim components to avoid damage, scratches, breaking of clips and/or interior trim panels.

Page 13 of 17

999F3 4W010II - Rev. 07.01.2010

INSTALLATION INSTRUCTIONS - Accent Lighting Kit 12) CHECKLIST Prior to completion, verify the following: 1)

Connect the battery negative terminal.

2)

Turn the vehicle ignition switch to the "ACC" position, push lighting control knob, and confirm the Accent Lighting illuminates.

3)

Turn the lighting control knob and confirm that the color changes through 20 variations.

4)

Press and hold control knob for 3 seconds and confirm that the Accent Lighting enters "Demo Mode" and cycles through colors. Press knob again to exit demo mode.

5)

Leaving the accessory ON, turn the interior Room Lamp to "DOOR" and ignition switch OFF. Open the door and confirm the Accent Lighting Illuminates.

6)

Leaving the accessory ON, and the ignition switch OFF, close and lock the door using CDL or Key Fob (if equipped). Confirm that the Accent Lighting turns off.

7)

Reset the radio presets to the recorded settings.

8)

Place the Accent Lighting Quick Reference card in the glove box.

9)

Check the trim for a proper flush fit after re-installing the interior components.

10) Clean the interior of the vehicle. 11) Inspect the vehicle interior and exterior for damage.

Page 14 of 17

999F3 7W010II - Rev. 07.01.2010

INSTALLATION INSTRUCTIONS - Accent Lighting Kit Mechanization of this Accent lighting kit

Pink

L i g h t

HMI

Red

S t i c k

Orange

Dark Blue

L i g h t

Blue Controller

Brown Green

Sky Blue

Black

Brown Open

Light Green Red

Page 15 of 17

999F3 4W010II - Rev. 07.01.2010

10mm 1 inch

Page 16 of 17

999F3 4W010II - Rev. 07.10.2010

INSTALLATION INSTRUCTIONS - Accent Lighting Kit Kit Contents:

Nissan Universal Accent Lighting Kit - 999F3 AW000 Parts Contained in Bag Labelled 'Installation Installation Kit'. Kit . 1 Cable tie 15" - Black

Qty

Part Number

4

2 Cable tie 11" - Black

2

3 Cable tie 4" - Black

13

4 Grey foam rectangle 80mm x 30mm x 5mm - Adhesive one side

6

5 Small bracket 28mm long

2

6 Medium M di b bracket k t 54 54mm llong

1

7 Large bracket 80mm long

1

8 Posi-tap connector - Red / Grey

3

999M1 VT000

9 Control knob (Black + white printing)

1

999F3 AW002

10 Alcohol preparation wipe

4

11 U' Nut

2

12 Module adhesive fixing 53mm x 74mm

1

13 Lens Retaining g Ring g 9mm OD - Black

2

14 Clear plastic lens - 7.5mm diameter

2

Pozi-drive 15 Pozi drive self-tap self tap screw 1/2" 1/2 long - Black

2

16 Encoder lock nut

1

17 Quick reference guide

1

18 Double-sided adhesive fixing 12mm x 20mm (All on one backing paper)

4

19 Double-sided adhesive fixing 12mm x 102mm (All on one backing paper)

4

20 Parts list / Replacement template 21 Vehicle interface harness

1

999V2 AW000

1

999F3 AW005

22 Encoder and harness assembly

1

999F3 AW006

23 Cup-holder lights and harness assembly

1

999F3 AW003

24 Foot-well F t ll lights li ht and dh harness assembly bl 25 Control module (within polythene zip bag)

1

999F3 AW001

1

999F3 AW004

999F3 AW007

Parts Not In 'Installation Kit' bag.

17 of 17

999F3 6X000II - Rev. 07.01.10