FLEXTRAY® Ceiling Support Methods Flip Clip™
• Accommodates 1/4" and 3/8" rod sizes • Installs quickly with a screwdriver or pliers thus reducing installation time • Requires only one hex nut (not included) to hang and level the Flextray • Retainer tabs can be bent over to lock-in the threaded rod and wire basket • Finishes __: ZN, FB, SS6
Part
Description
Qty./Box
Number
WB46H__
Flip Clip
50
Wt./Box lbs.
kg
5.2
2.36
Snap retainer stops in place after cable is loaded.
• Trapeze Clip installs fast • For use with trays up to 4” (100mm) deep, 12” (300mm) wide, and spans up to 8’-0” (2.44m) • Tray can be released from support to allow side cable loading • Accepts 1/4” and 3/8” threaded rod sizes • Finishes __: GS, BLE, SPC
Part
Description
Qty./Box
Number
TRAPEZE SUPT2__
Trapeze Support Clip
50 trapeze clips 100 retainer stops
Wt./Box lbs.
kg
7.0
3.17
Snap retainer stops in place after cable is loaded.
2” Center Hanger • • • •
For use with 2” (50mm) tray widths only Accepts 1/4” threaded rod Hardware sold separately Finishes __: GS, BLE, SPC
Part
Description
Qty./Box
Number
2 IN CTR SUPT__
Assemble with ATTACHMENT CLP & FTHDWE 1/4 hardware.
See page 5 for finish information
21
Center Support Hanger for FT2x2
50
Wt./Box lbs.
kg
5.0
2.27
Ceiling Support Methods
Trapeze Support
FLEXTRAY® Ceiling Support Methods Hold Down Plate Part
Slot Size
Qty./Box
Wt./Box
Number
lbs.
kg
SUPT WASHER__
.28” x .70”
50
4.7
2.13
FTA6HD__
.40” x .70”
50
3.5
1.59
• Easy way to mount 4" (100mm) wide tray for raceway run. • Use 1/4" screws to attach SUPT WASHER to your specific wall/stud application (hardware sold separately). • FTA6HD can be used in pairs to create a center-hung support using 3/8" rod. • To protect cables use threaded rod protector (page 23). • To complete 3/8" center hanger assembly use: 2 - FTA6HD 2 - HN 3/8"-16 hex nuts • Finish: ZN, SS6
Ceiling Support Methods
Mounting Bracket Part
Description
Qty./Box
Number
FTB2UB__
Light Duty Wall/Rack Bracket
10
Wt./Box lbs.
kg
2.1
0.95
• Designed to support FT2X2X10 Flextray • Click tabs for Flextray attachment • Use 1/4” hardware and washer (not included) to mount bracket • Finishes __: SS6
1" typ. (25 mm)
.26" typ. (6.6 mm)
Center Hung Clip Part
Description
Qty./Box
Number
CTR HUNG CLP__
Light Duty Center Hanger
50
Wt./Box lbs.
kg
4.0
1.81
• Use for light duty cabling applications • For use with 11/2” (38mm) & 2” (51mm) deep tray with 4” (100mm) and 6” (150mm) widths • Built-in hold down tab • Accepts 1/4” threaded rod • Threaded rod and nuts sold separately • Finishes __: GS, BLE, SPC
Assemble with 1/4” threaded rod and finned nut See page 5 for finish information
22
FLEXTRAY® Ceiling Support Methods Threaded Rod Protector • Use to protect cables from 1/4” to 1/2” threaded rod • PVC UL94V-O material • Color: Gray
Part
Description
Qty./Box
Number
Wt./Box lbs.
SB301-1/2x8__
Rod Protector
1
kg
0.01 0.004
Center Hanger • Center hangers install with only one threaded rod and hardware • Tabs for easy hold down (not available in stainless steel) • For use with 4” (100mm) to 24” (600mm) wide tray • Tubing protects cable • 6” (150mm) and 18” (450mm) width hangers have slightly offset center tubing to allow the tube to fit properly between wire grid • Accepts 1/4”, 3/8” & 1/2” threaded rod • Finishes __: EG, BLE, HD, SPC
Part
Use With
Actual
Number
Tray Width
Width
4 CTR HGR__
4” (100mm)
47/16” (112mm)
6” (150mm)
517/32” (140mm)
8” (200mm)
819/32” (218mm)
12” (300mm)
121/2” (317mm)
16 CTR HGR__
16” (400mm)
163/8” (416mm)
18 CTR HGR__
18” (450mm)
6 CTR HGR__ 8 CTR HGR__ 12 CTR HGR__
20 CTR HGR__ 24 CTR HGR__
Wt./Box lbs.
kg
1
1.6
0.72
1
1.7
0.77
1
1.9
0.86
1
2.7
1.22
1
3.2
1.45
17” (432mm)
1
3.3
1.49
20” (500mm)
209/32” (515mm)
1
3.6
1.63
24” (600mm)
243/16” (640mm)
1
4.3
1.95
Position hanger below tray. Tabs can be bent over for hold down.
See page 5 for finish information
23
Qty./Box
Ceiling Support Methods
8”
FLEXTRAY® Ceiling Support Methods Heavy Duty Center Hung Support Kit Part
Channel
Number
Length
WB5518CH__
18”
Qty./Box
1
• Designed for 1/2" ATR. Channel length of 18" supports 12", 18", 20", and 24" Flextray Systems. • Protection sleeve for ATR to prevent damage to cables. 1 • /2" ATR attachment hardware provided. • Flextray mounting attachment hardware provided. • Heavy Duty Center Hung Support assembly includes: (1) - SB3011/2x8 Threaded Rod Protector (2) - B202 Square Washers (2) - HN 1/2"-13 Hex Nuts (2) - N224WO, 1/4"-20 Channel Nuts (no spring) (2) - SRHMS 1/4"-20 x 1” Machine Screws (2) - SUPT WASHER Hold Down Plates (1) - B54SH Channel, 18" long • Finishes __: ZN, SPC
Wt./Box lbs.
kg
2.2
1.00
Ceiling Support Methods
Kit supplied with attachment hardware.
Trapeze Support Kits Part
Use With
Overall
Qty./Box
Number
Tray Width
Width
WB5506__
6” (150mm)
10” (254mm)
WB5508__
8” (200mm)
WB5512 __
Wt./Box lbs.
kg
1
1.6
0.73
12” (305mm)
1
1.7
0.77
12” (300mm)
16” (406mm)
1
2.0
0.91
WB5518 __
18” (450mm)
22” (559mm)
1
2.5
1.13
WB5524__
†
28” (711mm)
1
2.9
1.32
• Trapeze Support Kit includes all components required for single trapeze support in one package. • Designed for use with 1/4" ATR. • Also available for 3/8" ATR, add -3/8 suffix to part number. • Order threaded rod separately. • Finish: Channel - GLV Other components - ZN, SPC
† For 20” (500 mm) and 24” (600 mm) wide Flextray
Trapeze Kit for 1/4" ATR includes: (4) - B450-1/4" U-Washers (4) - HN 1/4"-20 Hex Nuts (1) - SUPT WASHER (1) - FN224 1/4"-20 EZ Twirl Nut (1) - SRHMS 1/4"-20 x 1" Machine Screw (1) - B54SH Channel
Trapeze Kit for 3/8" ATR add -3/8" suffix, includes: (4) - B450-3/8" U-Washers (4) - HN 3/8"-16 Hex Nuts (1) - SUPT WASHER (1) - FN224 1/4"-20 EZ Twirl Nut (1) - SRHMS 1/4"-20 x 1" Machine Screw Kits supplied with (1) - B54SH Channel attachment hardware. See page 5 for finish information
24
Overall Width
FLEXTRAY® Ceiling Support Methods Profile Supports Part
Use With
Actual
Number
Tray Width
Width
12 PROFILE SUPT__
up to 8” (200mm)
12.49” (317mm)
16 PROFILE SUPT__
12” (300mm)
24 PROFILE SUPT__ 28 PROFILE SUPT__
Qty./Box
Wt./Box lbs.
kg
1
0.80
0.36
16.39” (416mm)
1
1.07
0.48
16” (400mm) to 20” (500mm)
24.19” (614mm)
1
1.60
0.72
24” (600mm) to 26” (650mm)
28.05” (712mm)
1
1.87
0.85
Use profile for full tray bottom support Accepts 1/4”, 3/8” & 1/2” threaded rod - (rod and nuts not included) For use with 4” (100mm) to 24” (600mm) wide trays Items included: one (1) Profile Support two (2) SUPT WASHER two (2) FTHDWE 1/4 • Finishes __: GS, EG, BLE, HD, SPC Ceiling Support Methods
• • • •
Position hanger below tray. Install and tighten hardware.
Profile Length • 10’ section to allow field cutting to length • For use with 4” (100mm) to 32” (800mm) wide trays • Can support multiple runs at same time • Accepts 1/4” threaded rod • Use FTHDWE 1/4 and TOP WASHER for hold down (sold separately) • Finishes __: GS, BLE, HD, SPC
Part
Description
Qty./Box
Number
10 LFT PROFILE__
10’ nominal length 117” (2971mm) actual length Profile Tray Support
See page 5 for finish information
25
1
Wt./Box lbs.
kg
7.8
3.54
FLEXTRAY® Ceiling Support Methods KwikWire™ Clamps & Wire Rope • KwikWire system replaces jack chain or ATR to support lighting, ductwork, and Flextray. • Can be quickly installed around beams - No drilling required. • Ideal for sloped ceilings - can hang objects at up to 60° angles. • Simple height adjustments are made by releasing locking tab, no tools required. • Spools of wire can be cut to length in field, reducing waste and up front planning. Part
Clamp Description
Number
For Use With Rope Diameter
BKC100
1/16”
Qty./Box
& 3/32”
BKC150
3/32”
BKC200
1/8”
100
& 3/16”
50
Ceiling Support Methods
Part
Rope Diameter - Working Load
- 96 lbs.
500 ft.
(1)
3/32”
- 184 lbs.
500 ft.
BKW125 (1)
1/8”
- 340 lbs.
500 ft.
BKW188 (2)
3/16”
- 840 lbs.
250 ft.
BKW094
BKCC
BKC100
1/16”
0-75
BKC100
3/32”
25-150
BKC150
3/32”
25-150
BKC150
1/8”
25-250
BKC200
1/8”
25-250
BKC200
3/16”
50-640
Wire Rope Cutter
Wire Rope Construction
1
(1) 7 x 7
(2) 7 x 19
New
KwikWire™ Cable Assemblies
• New KwikWire “Y” Cable Assemblies will simplify the installation of light fixtures and cable tray. • “Y” Cables enable a single suspension point to provide two securement points. • “Y” legs are 18” in length. • “Y” Cable Assembly Kits include two (2) 10’-0” long cable assemblies and two (2) KwikWire clamps. • Add-on cable assemblies can be field installed on KwikWire systems.
Part
Wire Rope Dia.
Lbs. Safety Factor 5
* Working loads shown are for hanging vertically. For suspending at 15°, 30°, 45° or 60° angles from vertical, use the following percentage of the working loads from the chart:
Qty./Spool
1/16”
BKW063 (1)
Clamp Part No.
100
& 1/8”
Number
KwikWire™ Clamp Working Loads*
Description
Qty./Box
BKYC-094
Carabineer
20
BKYC-094-120K
Carabineer
10
BKYC-094
BKYC-094-120K
Number
See page 5 for finish information
26
15° = 96% 30° = 86% 45° = 70% 60° = 50%
FLEXTRAY® Ceiling Support Methods KwikWire™ Starter Kit • Starter Kit includes everything you need to get the job done. • Kits are packaged in a 5-gallon bucket for easy transportation. The lid includes a built-in cable counter to simplify measuring and cutting the wire rope to length. • Starter Kit includes KwikWire clamps, a spool of wire rope, and a cable cutter.
Kit Includes - Working Load
Qty./Box
BKS10063
BKC100 (100 pcs.), Cable Cutter 1/16ӯ Wire Rope (500 ft.)
1
BKS10094
BKC100 (100 pcs.), Cable Cutter 3/32ӯ Wire Rope (500 ft.)
1
BKS15094
BKC150 (100 pcs.), Cable Cutter 3/32ӯ Wire Rope (500 ft.)
1
BKS15125
BKC150 (100 pcs.), Cable Cutter 1/8ӯ Wire Rope (500 ft.)
1
BKS20125
BKC200 (50 pcs.), Cable Cutter 1/8ӯ Wire Rope (500 ft.)
1
BKS20188
BKC200 (50 pcs.), Cable Cutter 3/16ӯ Wire Rope (250 ft.)
1
KwikPak™ Wire Rope & Clamps KwikPak™ makes handling KwikWire™ a breeze! • Refill your starter kit with a B-Line KwikPak™. • KwikPaks include KwikWire clamps and a spool of wire rope. • KwikPaks are shipped in a specially designed dispenser box to ease field cutting of wire. Part
Kit Includes
Number
- Working Load
BKP10063
BKC100 (100 pcs.), Cable Cutter 1/16ӯ Wire Rope (500 ft.)
1
BKP10094
BKC100 (100 pcs.), Cable Cutter 3/32ӯ Wire Rope (500 ft.)
1
BKP15094
BKC150 (100 pcs.), Cable Cutter 3/32ӯ Wire Rope (500 ft.)
1
BKP15125
BKC150 (100 pcs.), Cable Cutter 1/8ӯ Wire Rope (500 ft.)
1
BKP20125
BKC200 (50 pcs.), Cable Cutter 1/8ӯ Wire Rope (500 ft.)
1
BKP20188
BKC200 (50 pcs.), Cable Cutter 3/16ӯ Wire Rope (250 ft.)
1
See page 5 for finish information
27
Qty./Box
Ceiling Support Methods
Part Number
New
FLEXTRAY® Wall Support Methods
Wall Support Methods
Wall Mounting Supports ............................
29
L Brackets
..................................
29
Z Brackets
..................................
30
Shelf Brackets
.........................
30
Mounting Bracket
.......................
30
Attachment Clips
........................
31
Support Washers
........................
31
.............................
31
Hold Down Plate
Wall Supports
....................
32
............................
32
.................................
33
Wall Termination Kit Wall Mount Kit C Brackets
28
FLEXTRAY® Wall Support Methods Shelf Brackets • Heavy-duty support bracket • For use with 6” (150mm) to 24” (600mm) wide trays • Built-in tab for hold down • Accepts 1/4” through 11/2” conduit sizes for additional support options • Optional hardware sold separately • Finishes __: GLV, HDG, SS6
Part
Use With
Number
Tray Width
FTB6CS__
6” (150mm)
FTB8CS__
Qty./Box
Wt./Box lbs.
kg
1
0.5
0.22
8” (200mm)
1
0.6
0.27
FTB12CS__
12” (300mm)
1
1.2
0.54
FTB16CS __
16” (400mm)
1
1.7
0.77
FTB18CS __
18” (450mm)
1
1.9
0.86
FTB20CS __
20” (500mm)
1
2.6
1.18
FTB24CS __
24” (600mm)
1
3.2
1.45
FTB24CS shown
• Installs tray to wall cleanly • Built-in tab for hold down (not available in stainless steel) • For use with 4” (100mm) to 24” (600mm) wide trays • Use with pedestal clamp in raised floor applications • Hardware sold separately • Finishes __: EG, HD, BLE, SPC
Part
Use With
Number
Tray Width
4 L BRKT__
4” (150mm)
8 L BRKT__
Qty./Box
Wt./Box lbs.
kg
1
0.6
0.27
6” (150mm) & 8” (200mm)
1
0.8
0.36
12 L BRKT__
12” (300mm)
1
1.3
0.59
16 L BRKT__
16” (400mm)
1
1.4
0.63
20 L BRKT__
20” (500mm)
1
2.0
0.91
24 L BRKT__
24” (600mm)
1
2.3
1.04
Tab can be bent over for hold down.
12 L BRKT
See page 5 for finish information
29
Wall Support Methods
L Brackets
FLEXTRAY® Wall Support Methods Z Brackets Part
Description
Qty./Box
Number
Z BRKT__
Z Bracket
1
• • • • • •
Wt./Box lbs.
kg
0.6
0.27
Used for horizontal and/or vertical mounting For use with 4” (100mm) to 32” (800mm) wide trays Can be used to offset trays from floor Can be used to terminate tray run at wall Multiple brackets can be used for wider tray widths Finishes __: GS, BLE, SPC
Use with two (2) each TOP WASHER & FTHDWE 1/4 (sold separately)
Hold Down Plate Part
Slot Size
Qty./Box
Number
Wt./Box lbs.
kg
SUPT WASHER__
.28” x .70”
50
4.7
2.13
FTA6HD__
.40” x .70”
50
3.5
1.59
Wall Support Methods
• Easy way to mount 4" (100mm) wide tray for raceway run. • Use 1/4" screws to attach SUPT WASHER to your specific wall/stud application (hardware sold separately). • FTA6HD can be used in pairs to create a center-hung support using 3/8" rod. • To protect cables use threaded rod protector (page 23). • To complete 3/8" center hanger assembly use: 2 - FTA6HD 2 - HN 3/8"-16 hex nuts • Finish: ZN, SS6
See page 5 for finish information
30
FLEXTRAY® Wall Support Methods Attachment Clips • Wall attachment for 2” (50mm) wide tray only (FT2X2X10) • Low-profile appearance • Built-in tab to hold down tray • Can also be used with 2” (50mm) Center Support (see page 17) • Hardware sold separately • Finishes __: GS, BLE, SPC
Part
Description
Qty./Box
Number
ATTACHMENT CLP__
Attachment Clip Support for FT2x2x20
50
Wt./Box lbs.
kg
3.4
1.54
Mounting Bracket • Designed to support FT2X2X10 Flextray • Click tabs for Flextray attachment • Use 1/4” hardware and washer (not included) to mount bracket • Finishes __: SS6
Part
Description
Qty./Box
Number
FTB2UB__
Light Duty Wall/Rack Bracket
10
Wt./Box lbs.
kg
2.1
0.95
Wall Support Methods
1" typ. (25 mm)
.26" typ. (6.6 mm)
Wall Supports • Use to attach 2” (50mm) or 4” (100mm) trays to walls, struts or cabinets • Use for raceway mounting • Mount to metal framing for vertical support • Tabs are built in for tray hold down • Mount to side rail for electrical box connection • Finishes __: GS, BLE, SPC
Part
Description
Qty./Box
Number
WALL SUPT__
See page 5 for finish information
31
Wall Support Bracket
1
Wt./Box lbs.
kg
0.6
0.27
FLEXTRAY® Wall Support Methods Wall Termination Kit Part
Length
Qty./Box
Number
WBWTK__
9”
1
Wt./Box lbs.
kg
1.3
0.59
• Kit includes all hardware necessary to support Flextray when terminated at a wall • Mount slotted angle to wall with up to 3/8" hardware (not included) • Finishes __: ZN, FB Wall Termination Kit includes: 1 1 1 1
-
SA276-9 Slotted Angle FTA6HD - Hold Down 3/8"-16 x 1" Slotted Head Screw 3/8"-16 Hex Nut
Wall Mount Kit Part
Length
Qty./Box
Number
Wt./Box lbs.
kg
Wall Support Methods
WB48WMK__
8”
1
0.76
0.35
WB1224WMK__
12”
1
1.22
0.55
• Kit includes all components necessary to mount Flextray to a wall horizontally or vertically • Mount strut to wall with up to 1/2" hardware (not included) • Finish: Channel - GLV Hardware - ZN Wall Mount Kit includes: WB48WMK WB1224WMK 1 1 1 2 1 2 1 2
B54SH Strut SUPT WASHER Hold Downs 1/4"-20 x 1" Slotted Head Screw N224WO Channel Nut
WB1224WMK shown
Horizontally Mounted Vertically Mounted See page 5 for finish information
32
FLEXTRAY® Wall Support Methods C Brackets • Tab can be used for hold down (stainless steel will not have these tabs) • For use with 4” (100mm) to 12” (300mm) wide trays • C Bracket attaches to hard ceiling types • All brackets are 77/8” (200mm) tall • Cables can be side loaded • L Brackets (page 29) and C Brackets can be combined for layered tray runs • Finishes __: EG, BLE, HD, SPC
Part
Description
Qty./Box
Number
Wt./Box lbs.
kg
4 C BRKT__
4” (100mm) C Bracket
1
1.2
0.54
8 C BRKT__
8” (200mm) C Bracket
1
1.4
0.63
12 C BRKT__ 12” (300mm) C Bracket
1
1.9
0.86
Assemble with SUPT WASHER & FTHDWE 1/4.
See page 5 for finish information
33
Wall Support Methods
Hold down tab.