FE599 Lever Lock Installation Instructions Alternate Faceplate
Important Information Lock Programming Code
OR
six (6) digits
User Code A
four (4) digits
User Code B
four (4) digits
Web Support: part2.schlage.com Customer Service: (877) 288-7707
Lever Cover
Baseplate
Cover screws (2)
Keypad
Latch
Pin wrench
Key Latch/strike screws (4)
AA Batteries (4) Strike
1
Locate Programming Code and Preset User Codes The programming code and the preset user codes are printed on the yellow stickers located on the back of the keypad and on the installation sheet that came in the box. Write these codes in the space provided on the first page.
2 Preset Codes
Códigos preajustados
Programming Code Código de programación Code de programmation Prog Code XXXXXX (FCC ID: P2GXXXXX) User Code A XXXX XXXXX User Code B XXXX SN XXXXXXXXX
User Codes Códigos de usuario Codes utilisateur
2
Installation Instructions Instrucciones de instalación Notice d'installation Préréglage des codes
Serial Number Número de serie Numéro de série Lock Model Modelo de la cerradura Modèle de serrure
!
OR
O
4 2³⁄₈” (60 mm)
Top Parte superior Haut
2³⁄₄” (70 mm) OR O OU
Top Parte superior Haut OR O OU
Prog Code XXXXXX (FCC ID: P2GXXXXX) User Code A XXXX XXXXX User Code B XXXX SN XXXXXXXXX
OU
Without these user codes, you can get locked out. Si no cuenta con estos códigos de usuario, es posible que no pueda abrir. Vous ne pouvez entrer sans déverrouiller à l'aide des codes d'utilisateur.
Alternate Faceplate Chapa frontal alterna Plateau à trous alternatif 2 ³⁄₄
3
(2)
Choose Faceplate to Match Door Escoja la placa delantera para emparejar la puerta Choisir la têtière pour égaler la porte
OR O OU
4
Instalación de la cerradura
1
Install Lock
2¹⁄₈” (53 mm) Hole Agujero Trou
Caution
Precaución
!
Installer le verrou 2³⁄₈” (60 mm) OR O OU 2³⁄₄” (70 mm)
Check Dimensions Revise las dimensiones Vérifier les dimensions
5¹⁄₂” (140 mm) Minimum Mínimo Minimum
2
6
Mise en garde
Prog Code XXXXXX (FCC ID: P2GXXXXX) User Code A XXXX XXXXX User Code B XXXX SN XXXXXXXXX
5
180°
3
Match arrows Las flechas deben quedar alineadas Aligner les flèches
7
4
Check Door Dimensions If your door does not match the dimensions shown, go to www.part2.schlage.com for instructions on how to prepare your door.
2C\,” (60 mm) OR 2C\v” (60 mm)
2Z\,” (53 mm) Hole
3
4
Install Strike Into Frame
If Necessary, Change Latch Faceplate Check edge of door to determine the type of faceplate required.
OR
5
Install Latch Latch must be flipped so that bevel faces toward door jamb.
Door Jamb
Door Jamb
OR
-80
4
¹⁄₄"
Re v. 0
¹⁄₈" (3– –¹⁄₄" 6m m) 15
0 ¹⁄ ₈"
8/0
7
Remove Sticker from back of Lock
P5
6
7
8
Install the Keypad Feed the cable under latch assembly as shown below. Then slide the tailpiece through the hole as shown below.
Adjust Hands-free Post The hands-free post is the threaded stud on back of lock. It’s purpose (in step 10) is to attach the lock and baseplate together so that the lock will hold itself on the door. Hands free post may need to be adjusted with a screwdriver to the dimensions shown below.
Hands-free post
Z\,”- Z\v” (3 mm - 6 mm) Hold keypad against door
Adjust with screwdriver so screw extends beyond door edge.
9
10
Feed Cable through Baseplate Feed the cable through the hole as shown below. DO NOT connect the cable at this point.
Slide Baseplate onto Door over Hands-free post Hands-free post should lock plate against door surface. If hands-free post does not lock plate onto door, see step 8 for adjustment.
Hands-free post
11
12
Connect the Cable Snap the connectors together.
Install Batteries and Battery Cover
13
Install Cover and Lever See step 14 on the next page to verify that the lever is handed correctly to match your door. If the lever does not snap into place easily, you may have to tap the lever with a hammer using a piece of wood to cushion it. Be careful not to damage the finish of the lever.
!
Tuck wires into open space on baseplate. Be careful not to pinch any wires between cover and baseplate.
14
Check Handing of Lever
Correct Go to step 15
Incorrect See steps below to change lever handing
To Change Lever Handing
b
a
d
c
15
Test Locking and Unlocking from the Interior
!
Test with door open to avoid possibly being locked out!
To Unlock, Press Button
To Lock, Press Button
Green light
Red light
(indicates unlocked)
16
(indicates locked)
Test Outside Entry (When Door is Locked) When you press your User Code (four numbers) on the keypad, the door will unlock for 5 seconds, allowing entry.
!
Test with door open to avoid possibly being locked out!
Programming Code XXXXXX User Code A xxxx S/N x-xxxxxxxx User Code B xxxx Model BE369
Press
(four numbers)
Green flash = unlock
on keypad
17
Verify that latch retracts when lever is turned
This portion of the setup is complete.
Follow the directions on document Document 2 is located at part2.schlage.com.
to continue setup.
FCC Notice This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this equipment not expressly approved by Schlage could void the user’s authority to operate the equipment. FCC ID: P2GFE599
IC: 7954A-FE599
PATENT NOTICE Schlage® products and those of its subsidiary companies and licensees may be covered by both issued and pending U.S. and foreign patents, copyrights and trademarks. Manufactured items are covered by one or more of the following patents: 5070715 5152558 5308131 5395144 5593193 5598726 5640863 5683127 5715717
