Caution This device is registered as an EMC for commercial purposes. Vendors and users should be aware of this EMC registration. If this device is sold or purchased by mistake, the device will need to be altered for domestic use.

FCC Compliance Statement Caution : Any changes or modifications in the construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.

Warning This is a class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take suitable correction measures

Warning 1. If the built-in Lithium battery is replaced by another type of battery, there is a risk of explosion. Therefore it is necessary to replace the battery with the same type of battery or an identical one. In addition, be sure to dispose of worn-out batteries properly because they may cause environmental pollution. 2. Do not throw the battery into a fire, or heat , disassemble, cut or discharge it because those treatments can cause the failure of device. 3. Do not recharge the remote controller’s battery.

Cautions 1. Do not put a large monitor or other heavy objects on the SVR-1630 when using it.

2. The SVR-1630 is designed for indoor use and therefore is not waterproof or dampproof. Therefore before use it is necessary to fully understand the operating environment requirements detailed in the user manual, and to use the device within the scope of the terms of service. For cleaning the device, wipe it gently using a clean and dry cloth.

3. The SVR-1630 can be damaged by electric shock. Be careful to use AC power of 110V ~ 220V.

4. The SVR-1630 can be damaged by physical shock because it contains an HDD. Therefore, do not throw or drop the device.

5. The SVR-1630 is made of metal. If it is thrown at anybody it may cause harm. Install the device in a safe place out of the reach of children.

6. If the SVR-1630 does not operate correctly, do not disassemble it without authorization. Contact your local agency for after sales service. The warranty will become invalid if it is disassembled without authorization.

7. The SVR-1630 can transfer images in real time via a network and can be used for monitoring, depending on the installation location. Therefore check the laws in the relevant area carefully, and then install the device in such a way as not to infringe any of its laws.

SVR-1630

Contents

Contents Executive Summary ................................................................................................................7 1.

Main Features of the SVR-1630......................................................................................7

2.

Component Check..........................................................................................................8

3.

Description of the Front/Rear View................................................................................10

Installation and Connection..................................................................................................12 4.

5.

6.

7.

8.

4

Basic Connection and Start-up......................................................................................12 4.1

Overall Layout .......................................................................................................12

4.2

Connecting a Camera............................................................................................13

4.3

Connecting a Monitor.............................................................................................14

4.3.1

Connecting a CCTV Monitor ...........................................................................14

4.3.2

Connecting a VGA Monitor..............................................................................14

4.4

Connecting Audio ..................................................................................................15

4.5

Supplying Power and Running ...............................................................................16

OSD Menu Configuration and Control ...........................................................................17 5.1

Menu Configuration ...............................................................................................17

5.2

Word Input.............................................................................................................18

Remote Controller Setup and Basic Control ..................................................................19 6.1

Setting ID of SVR-1630..........................................................................................19

6.2

Selecting SVR-1630 ..............................................................................................20

6.3

Operable Range of the Remote Controller .............................................................20

6.4

Loading batteries into the remote controller ..................................................20

SVR-1630 Installation Example.....................................................................................22 7.1

Basic Configuration................................................................................................22

7.2

Advanced Configuration.........................................................................................22

7.3

External Storage & Backup Configuration...............................................................23

7.4

Internet/Intranet Configuration................................................................................23

SVR-1630

Basic Setting .........................................................................................24

8.1

Viewing Images .....................................................................................................24

8.2

Setting Date and Time ...........................................................................................25

8.2.1

Time Zone ......................................................................................................25

8.2.2

Daylight Saving...............................................................................................25

8.2.3

Sync with NTP................................................................................................25

2004. 07. 2004 (v 1.0)

Samsung Techwin

Contents

8.2.4

Time Format ...................................................................................................26

8.2.5

Date Mode......................................................................................................26

8.2.6

Time ...............................................................................................................26

8.2.7

Apply Date/Time .............................................................................................26

8.3

9.

SVR-1630

Setting Recording Conditions.................................................................................26

8.3.1

Configuration Status .......................................................................................27

8.3.2

Channel Status ...............................................................................................27

8.3.3

Record Rate/Quality .......................................................................................28

8.3.4

Rate (fps)........................................................................................................28

8.3.5

Quality............................................................................................................28

8.3.6

Audio Record..................................................................................................28

8.3.7

Apply ..............................................................................................................28

Using Input/Output Terminals........................................................................................29 9.1

Connecting and Configuring the Sensor .................................................................30

9.1.1

Specification ...................................................................................................30

9.1.2

Connecting Sensor Input ................................................................................30

9.1.3

Setting Sensors ..............................................................................................31

9.2

Connecting and Setting Relay Output ....................................................................32

9.2.1

Specification ...................................................................................................32

9.2.2

Connecting to Relay Output Terminal ..............................................................32

9.2.3

Configuring Relay Out.....................................................................................33

9.3

Connecting and Configuring Serial Communication Ports.......................................34

9.3.1

Connecting Serial Communication Ports for Pan/Tilt/Zoom..............................34

9.3.2

Serial Communication Port Connection Layout................................................35

9.3.3

Serial Communication Port Figure...................................................................36

9.3.4

Configuring a Serial Port.................................................................................37

9.4

Connecting an External Device to a Serial Port ......................................................38

9.4.1

Connecting Text Input Devices (ATM / POS / Access Control) .........................38

9.4.2

Configuring Serial Setup (COM1)....................................................................39

9.4.3

Configuring Text..............................................................................................40

9.5

Connecting a USB Device......................................................................................41

9.6

Connecting Video In/Out ........................................................................................42

10.

HDD..........................................................................................................................43

10.1

Adding and Replacing HDDs on the HDD Rack......................................................43

10.1.1

Available HDDs ..............................................................................................43

10.1.2

Mounting an HDD ...........................................................................................43

Samsung Techwin

2004. 07. 2001 (v 1.0)

5

SVR-1630

10.2

Contents

Adding and Replacing External Storage Device......................................................46

10.2.1

IEEE1394 Port................................................................................................46

10.2.2

Connecting IEEE1394 Device.........................................................................46

10.3 11.

Registering and Formatting an HDD.......................................................................47 Remote Monitoring and Control.................................................................................48

11.1

Connecting via Ethernet.........................................................................................48

11.2

Configuring an SVR-1630 Network ........................................................................49

12.

Using the SVR Manager............................................................................................50

12.1

PC System Requirements for running the SVR Manager........................................50

12.2

Installing the SVR Manager ...................................................................................50

12.3

Uninstalling the SVR Manager ...............................................................................52

12.4

Configstation .........................................................................................................52

12.5

Monitor ..................................................................................................................53

12.6

Playback................................................................................................................54

Appendix ...............................................................................................................................55 1.

HDD .............................................................................................................................56 1.1

Fundamental Notions & Terms ...............................................................................56

1.1.1

SVR-1630 Storing Structure (VFS2) ............................................................56

1.1.2

Backup ...........................................................................................................56

1.1.3

Disk Manager .................................................................................................57

1.2

Replacing HDDs ....................................................................................................58

1.2.1

Checking HDDs ..............................................................................................58

1.2.2

When the primary disk fails .............................................................................58

1.2.3

When an auxiliary disk fails.............................................................................58

1.3

Keeping Data.........................................................................................................59

1.3.1

Backup ...........................................................................................................59

1.3.2

Separating and Preserving HDDs ...................................................................60

1.3.3

Cautions .........................................................................................................60

2.

Changing Video Type....................................................................................................61

3.

Using CD-Rom .............................................................................................................62

4.

6

3.1

CD- ROM DISC Components.................................................................................62

3.2

Preparation............................................................................................................62

3.3

Reading the User Manual in CD-ROM ...................................................................62

Specification .................................................................................................................63

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

Executive Summary 1. Main Features of the SVR-1630 The SVR-1630 is a new concept DVR, saving the video inputs, audio, text data and alarm data of 16 channels in two built-in HDDs, with its main features described below.

□ 16-Channel Video Input Support □ 1 Channel Audio Recording and Playback □ Max. 240fps Recording □ Real-time monitoring (30fps per channel) □ Built-in software multiplexer for 16-Channel split monitoring (1 / 2x2/3x3 /4x4 Screen Mode Support) □ Up to 4TB Storage Capacity (Expansion using IEEE 1394 Port) □ Text data recording by interlocking with ATM/POS devices □ 16 Sensor Inputs and 4 Interlocked Relay Outputs □ Hardware Motion Detection (64 Section) □ Backup using IEEE1394 and Network □ PTZ control □ Easy-to-use Color Graphic OSD □ Dynamic IP support □ IR Remote Controller □ Remote Management Software provided (SVR Manager) □ Dual CCTV Monitor support (3 Normal, 1 Spot) □ VGA monitor support □ CD-RW backup support (option)

Samsung Techwin

2004. 07. 2001 (v 1.0)

7

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

2. Component Check Please check the package to make sure that you receive all the accessories, including the components shown below.

1. SVR-1630 (1EA)

2. AC Power Cord (1EA)

3. CD-ROM (Including SVR Manager) (1EA)

4. Remote Controller (1EA)

5. Guide (2EA)

6. HDD Fixing KIT (1SET)

7. 19” RACK FIXING KIT (1SET)

8. HDD EARTH CABLE (1EA)

8

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

9. HDD Removable Rack KIT(1SET)

Samsung Techwin

2004. 07. 2001 (v 1.0)

9

SVR-1630

오류! 스타일이 정의되어 있지 않습니다.

3. Description of the Front/Rear View SVR-1630 Front View

(1) Power Switch (2) HDD Removable Rack (3) Function Buttons (4) Channel Buttons (5) Status LED (6) Jog Shuttle for Search and Playback (7) Function Switch (8) Play and Search Button (9) Search/Preset Switch (10) Remote Controller Receiver (11) USB Connector (12) IEEE 1394 Connector (13) Bracket fixing hole for rack mount

10

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

SVR-1630 Rear View

(14) BNC connector for video output (15) BNC connector for video input (16) BNC connector for Monitor A output (17) BNC connector for Monitor A input (18) Ethernet connector (19) GND (20) Input/output terminal for RS232 & RS422/485 (21) IEEE 1394 connector (22) S-VHS connector for Monitor A output (23) Input/output terminals for sensor, relay and serial (24) RS232 connector (9Pin D-Sub) (25) Connector for VGA monitor (26) RCA connector for audio input/output (27) AC power input connector

Samsung Techwin

2004. 07. 2001 (v 1.0)

11

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

Installation and Connection 4. Basic Connection and Start-up 4.1 Overall Layout (1) The devices that can be connected to the SVR-1630 are described below. See each relevant section in the installation manual for the contents on the figure.

12

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

4.2 Connecting a Camera (1) Connect a camera to the SVR-1630 using the coaxial cable as shown in the figure below.

1. The input video type should be either NTSC or PAL. Do not use both types at the same time. 2. Automatic setting of 75Ω terminal resistance Two video terminals are internally connected. A terminal resistance of 75Ω exists when only one terminal is connected. Hi-z exists when both terminals are connected. See “9.6. Connecting Video In/Out ” on the page 42. 3. The Input Video Type (NTSC/PAL) is automatically recognized when the device runs. For the recognition sequence, camera number 1 is recognized first, and then the sequence is decided according to the camera signal type that is first detected, from cameras no. 1 to 16. When no cameras are connected, the internal jumper setting is applied. To change the internal jumper, see page 61, Appendix “2. Changing Video Type”

Samsung Techwin

2004. 07. 2001 (v 1.0)

13

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

4.3 Connecting a Monitor 4.3.1 Connecting a CCTV Monitor (1) Connect a monitor to the SVR-1630 using the coaxial cable as shown in the figure below.

4.3.2 Connecting a VGA Monitor (1) Monitor Outuput A can output to VGA. For better definition quality, connect Monitor A to the VGA Monitor as shown in the figure below.

1. The SVR-1630 monitor outputs are divided into A (Normal) and B (Spot). If only one monitor is connected, connect Monitor A. 2. For Monitor Output A, the same video output is transferred to two BNC connectors and an S-VHS connector.

14

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

4.4 Connecting Audio (1) Connect an audio signal to the SVR-1630 using the RCA cable as shown in the figure below.

Samsung Techwin

2004. 07. 2001 (v 1.0)

15

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

4.5 Supplying Power and Running (1) Connect the power cable as shown in the figure below.

1. Connect the power cable, press the power switch, and the device starts booting. 2.Press and release the power switch while SVR-1630 is ON, the following windows are displayed according to the system setting after 4 seconds. When there is Admin password in “System Setup” The dialogue box asking to enter the admin password is appeared. Enter the password, and the power is off. When there is no Admin password in “System Setup” The dialogue box asking “Yes” or “No” is appeared. Select “Yes”, and the power is off. 3. For turning the power on again, press the power switch.

16

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

5. OSD Menu Configuration and Control 5.1 Menu Configuration Press the [MENU] button on the keypad on the front panel, and the system changes to the SVR-1630 Setup mode. The OSD Menu is displayed as shown in the figure below. The Jog/Shuttle on the menu is controlled as described in the figure below.

① Main Menu

② Sub-menu

③ Setup Dialogue Box

Samsung Techwin

2004. 07. 2001 (v 1.0)

17

SVR-1630

오류! 스타일이 정의되어 있지 않습니다.

(1) Main Menu : The selected tab is shown in blue and the related sub-menus will be shown below the tab. To move to the previous/next Main Menu Tab, use the [◀/▶] arrow buttons. To move to the relevant submenu, press the [ENTER] or [▼] buttons.

(2) Sub-menu : The selected sub-menu is shown in blue and the related setting page will be shown to the right of the sub-menu. Use the [▲/▼] arrow buttons to move within the sub-menu list. To move to the setting page, press the [ENTER] button. To go to the Main Menu, press the [ESC] button.

(3) Setting Page : The selected item is shown with a circle to the left of its name. The field to set values is shown in gray. To move within each page, use the [◀/▶] or [▲/▼] arrow buttons. Press the [ENTER] button to change the value of a setting. The setting values of items are divided into text (including letters and numbers) and numbers. When the setting value is a word, a dialogue box to edit the word will open. When the setting value is a number, it should be set by using the [◀/▶] or [▲/▼] arrow buttons. After the value is set, press the [ESC] button. To go to the Main Menu, press the [ESC] button.

5.2 Word Input Select a value using the [▲/▼] buttons. Press the [ENTER] button to confirm the selected value.

18

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

6. Remote Controller Setup and Basic Control 6.1 Setting ID of SVR-1630 When controlling several SVR-1630s with one remote controller, multiple DVRs can be set by one remote controller. Set the remote controller ID as described below.

(1) Press the [MENU] button. (2) Select “System” by using the [▶] button and press the [ENTER] or [▼] button. (3) Select “Etc.” using the [▼] button and press the [ENTER] button. (4) Select “Remote Control ID,” and press the [ENTER] button. (5) Select a value using the [◀/▶] buttons and press the [ESC] button. (6) Press the [ESC] button to return to Monitor mode.

Samsung Techwin

2004. 07. 2001 (v 1.0)

19

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

6.2 Selecting SVR-1630 Multiple DVRs with different IDs can be controlled by one remote controller. To select a specific SVR-1630, press the ID button of the remote controller. When the DVR ID matches the remote controller ID, the LED on the front of the SVR-1630 lights up and a buzzer sounds for two seconds.

Up to 16 Remote Controller IDs are supported, which consist of two digits from 1 to 4. ID

Key Sets

ID

Key Sets

ID

Key Sets

ID

Key Sets

ID1-1

1,1

ID2-1

2,1

ID3-1

3,1

ID4-1

4,1

ID1-2

1,2

ID2-2

2,2

ID3-2

3,2

ID4-2

4,2

ID1-3

1,3

ID2-3

2,3

ID3-3

3,3

ID4-3

4,3

ID1-4

1,4

ID2-4

2,4

ID3-4

3,4

ID4-4

4,4

6.3 Operable Range of the Remote Controller

6.4 Loading batteries into the remote controller The remote controller uses only AAA-type batteries. The batteries are loaded into the remote controller as

described below. 1. Remove the battery cover. 2. Check battery polarity and insert batteries.

20

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

3. Replace the battery cover.

Samsung Techwin

2004. 07. 2001 (v 1.0)

21

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

7. SVR-1630 Installation Example 7.1 Basic Configuration

7.2 Advanced Configuration

22

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

7.3 External Storage & Backup Configuration

7.4 Internet/Intranet Configuration

Samsung Techwin

2004. 07. 2001 (v 1.0)

23

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

8. SVR-1630 Basic Setting 8.1 Viewing Images After initial start-up, images are displayed in a split screen corresponding to the number of channels connected to the monitor.

If the user password is set, a prompt for entering the password will appear. The keypad on the front panel won’t work. (A user password is not set in the factory)

24

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

8.2 Setting Date and Time

(1) Press the [MENU] button, and select the “Quick Setup” tab on the OSD Menu. (2) Select “Date/Time” using the [ENTER] or [▼] button and press [ENTER].

8.2.1 Time Zone (1) Select “Time Zone” using the [◀/▶] or [▲/▼] arrow buttons and press the [ENTER] button. (2) Select a value using the [◀/▶] buttons and press the [ESC] button when finished.

8.2.2 Daylight Saving (1) “Daylight Saving Time” is only activated when the time zone is selected. (2) Select “Daylight Saving” using the [◀/▶] or [▲/▼] arrow buttons and press the [ENTER] button.

(3) Select “Yes/No” using the [◀/▶] buttons and press the [ESC] button.

8.2.3 Sync with NTP In order to synchronize time with the NTP (Network Time Protocol) server, select “On”. (1) Select “Sync with NTP” using the [◀/▶] or the [▲/▼] buttons and press the [ENTER] button. (2) Select “On/Off” using the [◀/▶] buttons and press the [ESC] button.

Samsung Techwin

2004. 07. 2001 (v 1.0)

25

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

8.2.4 Time Format (1) Select “Time Format” using the [◀/▶] or [▲/▼] buttons and press [ENTER]. (2) Two Time Formats are available; ‘MM/DD/YYYY’ ,‘YYYY/MM/DD’ ‘DD/MM/YYYY’. Select a value using the [▲/▼] buttons, and press the [ESC] button when finished. (Default value is ‘MM/DD/YYYY’.)

8.2.5 Date Mode (1) Select “Date Mode” using the [◀/▶] or [▲/▼] buttons and press [ENTER]. (2) Select ‘MM’/‘DD’/‘YYYY’ using the [◀/▶]buttons, and select the value using the [▲/▼] buttons. (3) Press the [ESC] button when finished.

8.2.6 Time (1) Select “Time” using the [◀/▶] or [▲/▼] buttons and press [ENTER]. (2) Select ‘HH’/‘MM’ using the [◀/▶] buttons, and select the value using the [▲/▼] buttons. (3) Press the [ESC] button when finished.

8.2.7 Apply Date/Time Most setting values are applied automatically when exiting from the related menu page. But “Date”& “Time” settings are not applied automatically because they may critically affect the file system of the recorded HDD. To apply Date/Time settings, confirm the settings with the [Apply Date/Time] button.

(1) Select “Apply Date/time” using the [◀/▶] or [▲/▼] buttons and press [ENTER]. A warning message will appear.

Select “Yes” using the [◀/▶] or [▲/▼] buttons and press [ENTER]. To cancel, press the [ESC] button.

8.3 Setting Recording Conditions Recording conditions under the “Quick Setup” menu tab apply the same values to all 1~16analog channels. All settings are applied for 24 hours/day regardless of the values set for “Time Schedule” or “Alarm Rec.”

26

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

(1) Press the [MENU] button, and select “Quick Setup.” (2) Move to a sub-menu by pressing [ENTER] or the [▼] button. (3) Select “Recording” using the [▲/▼] buttons and press the [ENTER] button.

8.3.1 Configuration Status Displays the recording configuration status. Indicates where the final setting is done. When setting up through the “Quick Setup” menu, “Macro Setup” will be shown. When setting up through “Schedule Rec.” or “Event Rec.,” “Custom Setup” will be shown.

“Macro Setup” is only shown when the schedule recording conditions for all 16 channels are the same.

8.3.2 Channel Status (1) Select “Channel Status” using the [▲/▼] buttons and press the [ENTER] button. (2) Select a value using the [◀/▶] buttons. Press the [ESC] button when finished.

Samsung Techwin

2004. 07. 2001 (v 1.0)

27

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

8.3.3 Record Rate/Quality (1) Select “Recording Speed/Quality” using the [▲/▼] buttons and press the [ENTER] button. (2) Select a value using the [◀/▶] buttons. Press the [ESC] button when finished.

Record Rate/Quality means Low : Rate=1fps and Quality=Q5 Std. : Rate=5fps and Quality=Q5 High : Rate=15fps and Quality=Q5 Customer : Rate and Quality = Manually defined by User.

8.3.4 Rate (fps) When “Recording Speed/Quality” is set as “Customer,” values can be set manually.

(1) Select “Speed” using the [▲/▼] buttons and press the [ENTER] button. (2) Select a value using the [◀/▶] buttons. Press the [ESC] button when finished.

8.3.5 Quality When “Recording Speed/Quality” is set as “Customer,” values can be set manually.

(1) Select “Quality” using the [▲/▼] buttons and press the [ENTER] button. (2) Select a value using the [◀/▶] buttons. Press the [ESC] button when finished.

8.3.6 Audio Record (1) Select “Audio Record” using the [▲/▼] buttons and press the [ENTER] button. (2) Select a value using the [◀/▶] buttons. Press the [ESC] button when finished.

8.3.7 Apply (1) Select “Apply” using the [▲/▼] buttons and press the [ENTER] button. (2) Setting values are applied and the previous menu will be displayed.

28

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

9. Using Input/Output Terminals Wiring Terminating Wires The wires for the TERMINAL BLOCK are terminated as described below. When solid and stranded wires are used, be careful because the thickness of usable wires varies. Stranded Wire: Strip the outer covering to the defined length (8~10mm) and solder it. Suitable wires are AWG 22 ~ 26. Solid Wire: Strip the outer covering to the defined

length

(8~10mm).

Suitable

wires are AWG 20 ~ 26.

Inserting/removing wires For inserting into or removing wires from the TERMINAL BLOCK, push the lever as shown in the figure.

Samsung Techwin

2004. 07. 2001 (v 1.0)

29

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

9.1 Connecting and Configuring the Sensor 9.1.1 Specification The sensor input of the SVR-1630 has the specifications and normal operating conditions as described below.

Specification

No. of Input Circuits

16 Photocoupler Inputs

Input Type

N.C, N.O supported

Sensor

Dry Contact Sensor

Connection

Connect the stripped wires to the Terminal Block.

Valid Electrical Performance

Input

Pulse Minimum 500ms

Duration Output Currents

Typical DC 12mA

9.1.2 Connecting Sensor Input For connection of sensor inputs S1 ~ S16, see the figure below. The figure below is an example of dry contact sensor connection. For connecting or removing wires, see “Preparing and Connecting Wires” on page 29. For connecting sensors (Open Collector output, etc.) other than dry contact sensors, it is necessary to contact the Samsung Techwin CS team.

30

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

9.1.3 Setting Sensors

(1) Press the [MENU] button, and the OSD Configuration menu appears. Select “Event Source”. (2) Go to the Sub-menu using the [ENTER] or [▼] buttons. Select “Sensor” and press the [Enter] button

9.1.3.1

All Ch

Used for setting 16 sensors at the same time. Set the Off, or Normal Open (N.O.) / Normal Close (N.C.) type. (1) Select ‘All Ch’ and set the type. (2) Press the “Apply” button to confirm the setting. 9.1.3.2

Configuration

Used for individually setting 16 sensors. Select and set each sensor. (1) Select “Configuration” and press the [Enter] button. (2) Select the sensor (S1~S16) to set and set the type. (3) After setting, press the [ESC] key to return to the ODS menu. 1. Sensor setting is for deciding whether to use sensors, and the sensor type. Storing according to sensor inputs and relay should be set separately. 2. See “Event Rec.” of the “SVR-1630 User Manual” for storing and “Event Act” for relay output.

Samsung Techwin

2004. 07. 2001 (v 1.0)

31

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

9.2 Connecting and Setting Relay Output 9.2.1 Specification The alarm output of the SVR-1630 has the specifications and normal operating conditions as described below.

Spec.

No. of Output Circuits

Automatic output of 4 Relays

Output Method

Dry Contact

Connection

Connect the stripped wires to the Terminal Block.

DC

24V DC, 1.25A, 30W 125V DC, 0.24A, 30W

Rated Values

AC

125V AC, 0.5A, 62.5VA 250V AC, 0.25A, 62.5VA

9.2.2 Connecting to Relay Output Terminal For connection of R1 ~ R4 outputs, see the figure below. The figure below is an example for connecting the warning lamp. For connecting or removing wires, see “Wiring” on page 28.

32

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

9.2.3 Configuring Relay Out

Each relay can be synchronized with a sensor input or with motion detection, and its operation condition can be set differently according to the schedule. Relays can also be controlled locally by pressing the [RELAY] button followed by the relay number. Relays can also be controlled remotely through the “SVR Manager software.”

See the “SVR-1630 User Manual” for setting details.

Samsung Techwin

2004. 07. 2001 (v 1.0)

33

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

9.3 Connecting and Configuring Serial Communication Ports 9.3.1 Connecting Serial Communication Ports for Pan/Tilt/Zoom PTZ devices can only be connected and controlled provided that the SVR-1630 supports a through COM port. Check the models available in the SVR-1630OSD Menu. The figure below is an example for connecting an RS485 (COM2) communication terminal to a PTZ camera. Connect other serial communication ports to other devices by referring to the connection layout in the figure below. For connecting or removing wires, see

“Preparing and Connecting Wires” on page 29.

34

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

9.3.2 Serial Communication Port Connection Layout 9.3.2.1

COM1 Connection Layout

9.3.2.2

COM2 Connection Layout

9.3.2.3

COM3 Connection Layout

Samsung Techwin

2004. 07. 2001 (v 1.0)

35

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

9.3.2.4

COM4 Connection Layout

9.3.3 Serial Communication Port Figure 9.3.3.1

COM1 Figure

9.3.3.2

COM3/COM/4 Figure

36

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

9.3.4

SVR-1630

Configuring a Serial Port

Configure the COM port for PTZ and available models in the SVR-1630 “System / Serial Setup” .

After completing the serial setup, configure the base address or port for each channel under the “Camera” menu tab. When connecting PTZ devices to several cameras, be sure of the base address setting.

Samsung Techwin

2004. 07. 2001 (v 1.0)

37

SVR-1630

오류! 스타일이 정의되어 있지 않습니다.

9.4 Connecting an External Device to a Serial Port 9.4.1 Connecting Text Input Devices (ATM / POS / Access Control) In addition to images, the SVR-1630 can record text data received from a POS/ATM through the RS232 serial port (COM1).

Connect RS232 (COM1) by referring to the “9.3.3.1. COM1 Figure” on page 36. Set the text data in the “Event Source” menu and Serial data in the SVR-1630 “System” menu.

38

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

9.4.2 Configuring Serial Setup (COM1)

(1) Select “System” from the OSD Menu and go to the Sub-menu. (2) Select COM1 RS232 in “Serial Setup” and set the Device to “Text”. (3) Set the Baud Rate/Parity/Stop bit/Data bits to the same values as the input device.

Samsung Techwin

2004. 07. 2001 (v 1.0)

39

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

9.4.3 Configuring Text

(1) Select “Event Source” from the OSD Menu and go to the sub-menu. (2) Select “Text” and set the text related data.

Some external devices may not be recognized, depending on their characteristics. Before installing any external device, consult your local vendor.

40

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

9.5 Connecting a USB Device A USB port generally uses a USB memtory for a simple video copy. For connecting a USB device, its rated values shall not exceed the specification defined below.

USB Spec. Available Devices Output Voltage/Current

Ver 1.1 (Max 12M bps) USB Memory DC 5V / Max. 200mA

The disk should be formatted to the FAT32 type.

If properly connected, the disk is recognized automatically as in the following picture. To copy images, the process is as follows: Set copy range (up to 1 minute) Æ Select Disk Æ Copy (press “Start”).

Copy Images Time

5 sec

Select Disk

1 Disk(s)

Type

Model

Size (KB)

[F] Ext

Sony Flash Memory

6640

Start

Samsung Techwin

2004. 07. 2001 (v 1.0)

41

SVR-1630

오류! 스타일이 정의되어 있지 않습니다.

1. Note that USB Memory products that require a Windows program to operate may not be recognized by the SVR-1630.

2. See the “SVR-1630 User’s Manual” for details about Copy functions.

9.6 Connecting Video In/Out For the SVR-1630, the loop through Video In and Out automatically detects the connection status and sets the terminal resistance. For example, if only Video In is connected, the terminal resistance is internally set to 75Ω. If both Video In and Out are connected, the terminal resistance is changed to Hi-z. Therefore, for connecting both Video In and Out, the terminal resistance receiving the signal should be set to 75Ω.

42

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

10. HDD 10.1 Adding and Replacing HDDs on the HDD Rack 10.1.1 Available HDDs It is recommended to use the following HDD models with the SVR-1630. If a non-recommended HDD is used, Samsung Techwin’s warranty will not cover any failures.

Maker : MAXTOR Series

Model No.

Capacity

6Y120L(P)0

120GB

6Y250P0

250GB

DiamondMax Plus 9 (7200rpm)

The buffer for DiamondMax Plus 9’s model “L” is 2MB; for model “P” the buffer is 8MB.

10.1.2 Mounting an HDD (1) Check if the HDD is currently set as “Master”. (2) Turn off the SVR-1630’s power.

Samsung Techwin

2004. 07. 2001 (v 1.0)

43

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

(3) Unlock the rack by turning the key anti-clockwise.

(4) Pull the handle of the HDD RACK to completely remove the rack from the SVR-1630 main unit.

(5) Remove the cover by pulling the hook on the cover as shown in the figure below.

44

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

(6) Connect the connector inside the rack to the HDD. Fix the HDD using the screws included in the package’s accessories and close the cover. (Fix the HDD with care, avoiding giving it any knocks.)

(7) Drop the handle and push the rack until it reaches the back of the SVR-1630’s main unit.

(8) Lock the rack using a key.

Samsung Techwin

2004. 07. 2001 (v 1.0)

45

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

10.2 Adding and Replacing External Storage Device 10.2.1 IEEE1394 Port The SVR-1630 used IEEE1394 for the external storage device interface. It has two IEEE1394 ports, one each on the front and rear panel. With them the SVR-1630 can expand storage capacity up to 4TB.

Some IEEE1394 bays may not be recognized by the SVR-1630. Before purchasing, consult your local vendor to confirm compatibility.

10.2.2 Connecting IEEE1394 Device When using a FireWire supported external HDD, hard drive bays can be connected to a port in the front panel or a port in the rear panel. The SVR-1630 does not supply power to the hard drive bay; therefore only bays that use external power can be used.

When an external HDD is connected while the SVR-1630 is running, the SVR-1630 should correctly detect the external HDD. If it doesn’t, it is recommended to try connection as follows. 1. Power off the SVR-1630 and external HDD. 2. Connect the external HDD to the IEEE1394 port. 3. Power on the external device. 4. Power on the SVR-1630

46

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

10.3 Registering and Formatting an HDD The “Disk Manager” will automatically run on start-up after installing a HDD. If the “Disk Manager” doesn’t run automatically on start-up, make sure the HDD is properly installed.

(1) Press the [ENTER] button at “Select Disk”. (2) Select the newly-added HDD (indicated as “[F]”) using the [▲/▼] buttons and press the [ESC] button (3) Select “Action” using the [▲/▼] buttons and press the [ESC] button. (4) Select “Add” using the [◀/▶] buttons and press the [ESC] button. (5) Select “Apply” using the [▲/▼] buttons and press the [ESC] button. The HDD status is changed to “[*]”. And the new HDD is successfully registered. (6) Select “Action” using the [▲/▼] buttons and press the [ESC] button. (7) Select “Format” using the [◀/▶] buttons and press the [ESC] button. (8) Select “Apply” using the [▲/▼] buttons and press the [ESC] button. The HDD status is changed to “[R]” after formatting. (9) Shut down the “Disk Manager” by pressing the [ESC] button.

Samsung Techwin

2004. 07. 2001 (v 1.0)

47

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

11. Remote Monitoring and Control The SVR-1630 can be accessed using a remote PC via the Internet/Intranet. As with the local site, the SVR1630 can be controlled and monitored from remote sites via the Internet/Intranet.

11.1 Connecting via Ethernet

(1) Turn off the SVR-1630’s power switch. (2) Connect the SVR-1630 to the hub with an Ethernet cable. (3) Turn on the SVR-1630’s power switch.

1. Supply power to the SVR-1630 only after connecting the Ethernet cable, to avoid electrical damage to the

SVR-1630. 2. Firmly connect the Ethernet cable by fully pushing it into the hub. 3. Check the LED on the SVR-1630’s rear panel after supplying power.

48

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

11.2 Configuring an SVR-1630 Network The following description is on based on Ethernet connection. For more detailed information on the Network Settings Page and when xDSL is used, please refer to the “SVR-1630 User Manual”

(1) Press the [MENU] button. (2) Select “System” using the [◀/▶] buttons and press [ENTER]. (3) Select “Network” using the [▲/▼] buttons and press [ENTER]. (4) Select “IP Addr” using the [▲/▼] buttons and press [ENTER]. (5) Press the [ESC] button after entering the IP address in the dialogue box. (6) Select “Net Mask” using the [▲/▼] buttons and press [ENTER]. (7) Press the [ESC] button after entering the Net Mask in the dialogue box. (8) Select “Gateway” using the [▲/▼] buttons and press [ENTER]. (9) Press the [ESC] button after entering the Gateway in the dialogue box. (10) Select “DNS” using the [▲/▼] buttons and press [ENTER]. (11) Press the [ESC] button after entering the DNS in the dialogue box. (12) Press the [ESC] button until the Monitor Mode appears.

Samsung Techwin

2004. 07. 2001 (v 1.0)

49

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

12. Using the SVR Manager 12.1 PC System Requirements for running the SVR Manager Minimum Requirements

Recommended Requirements

CPU

P-Ⅲ 600MHz or above

P-Ⅲ 1GHz or above

RAM

128 MB or above

256 MB or above

VGA

16 MB or above

32 MB or above

OS

Windows 2000/XP

Windows 2000/XP

Resolution

1024 X 768 pixels or above

1024 X 768 pixels or above

Network

100 Base TX Fast Ethernet

100 Base TX Fast Ethernet

12.2 Installing the SVR Manager (1) Insert the Setup CD-ROM into the CD-ROM drive of the administrator’s PC (2) Double click the SVR Manager setup file. The Install Shield Wizard will be automatically installed. (3) Click the “I Agree” button to accept the license agreement

50

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

(1) Press the “Next” button.

(2) Browse and choose a directory if the default directory is not preferred. Click the “Install” button, after selecting a directory to install into.

(3) Click the “Close” button after the SVR Manager program is installed successfully.

Samsung Techwin

2004. 07. 2001 (v 1.0)

51

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

12.3 Uninstalling the SVR Manager (1) Click the Windows “Start” Button. (2) Select and Click the ‘Uninstall’ icon to run the Uninstall Shield.

(3) Uninstall the program according to the instructions in the window.

12.4 Configstation

Click the icon on the desktop to run the “SVR Manager Configstation” program.

52

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

12.5 Monitor

Click the related icon and run the “SVR Manager Monitor” program.

Samsung Techwin

2004. 07. 2001 (v 1.0)

53

SVR-1630

오류! 스타일이 정의되어 있지 않습니다.

12.6 Playback

Click the related icon and run the “SVR Manager Playback” program.

54

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

Appendix

Samsung Techwin

2004. 07. 2001 (v 1.0)

55

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

1. HDD 1.1 Fundamental Notions & Terms 1.1.1 SVR-1630 Storing Structure (VFS2) Samsung Techwin has developed a unique storage system suitable for SVR and has applied it to the SVR1630. The basic features are described below.

(1) It is theoretically possible to connect 3 physical HDDs internally (Internal, ATA Interface) and 24 HDDs externally (External: 2 IEEE1394 ports). The total number of HDDs that can be connected internally and externally is 24. (2) All of the connected HDDs are recognized as one virtual disk, and the SVR-1630 supports up to 4TB. (3) The HDD that is firstly connected becomes the primary disk and other HDDs are classified to auxiliary disks.

ATA (or EIDE) supports two channel interfaces (Primary/Secondary). Each channel can be connected to two devices (Master/Slave, HDD/CD-ROM). The Primary Interface connects a total of two HDDs and the Secondary Interface connects the HDD Rack and CD-RW. In order to prevent confusion with the VFS2’s Primary Disk, we will not use the terms Primary/Secondary.

(4) Each disk is composed of a Log Partition and a Schedule Partition.

Log Partition

To store recorded data information

Schedule Partition

To store images recorded according to the storing schedule

1.1.2 Backup (1) Backup is possible only through an IEEE1394 port, and the HDD for backup should be formatted to the FAT32 type. (The type is indicated as [F] in the Disk Manager.)

56

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

1.1.3 Disk Manager (1) When an HDD is added or deleted physically, the Disk Manager runs automatically after rebooting. If it doesn’t, you can run “MenuÆDiskÆDisk Manager” from the console.

(2) HDD Type [R]

Available for recording depending on successful formatting of the HDD

[V]

Connected and formatted as a DVR file system. If using the ‘Add used’ command, it will be changed to [R]. There is no need to reformat.

[F]

Connected, but not available, file system. After using ‘Add’, you need to format to make it like [R]. Otherwise indicates the FAT 32 file system connected for backup.

[C]

Built-in or external CD-Recorder

[X]

The HDD cable is not connected or has some problem. In this case, the HDD should be removed using the ‘Confirm Removed’ menu.

IntA

Internal Primary HDD

IntB

Internal Auxiliary HDD

R-HDD

HDD in the built-in hard disk rack

Ext

External HDD listing order can be changed according to the recognition sequence.

Samsung Techwin

2004. 07. 2001 (v 1.0)

57

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

(3) HDD Managing Command Add

Adds an HDD for recording. The HDD added is automatically formatted.

Add Used

Adds an HDD that has been used and formatted. There is no need to reformat. Only possible when the HDD is added as a Primary Disk.

Remove

Removes the current HDD. HDDs can be reused without data loss by using the ‘Add Used’ command.

Confirm Removed

Used when a removed HDD is still listed. ALL DATA WILL BE LOST!

1.2 Replacing HDDs 1.2.1 Checking HDDs The DVR file system (VFS2) automatically detects bad sectors, and bad sectors detected are not used. The cases below are for when an HDD fails or has some connection problems. (1) When replaying is stopped, or the DVR is rebooted in a specific sector during playback, or when it is not possible to search images by event. (2) When recording is stopped and the “Disk Manager” shows the HDD type as [X]

1.2.2 When the primary disk fails When the primary HDD fails, none of the data in the connected HDDs can be used. So the failed HDD should be replaced and all the connected HDDs should be removed, added and formatted again.

1.2.3 When an auxiliary disk fails The failed auxiliary disk should be replaced and reinstalled in “Disk Manager”. (“Add” -> “Format”).

58

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

1.3 Keeping Data To keep stored data for certain periods or semi-permanently, you should separate and keep HDDs with data on them.

1.3.1 Backup (1) Connect a backup HDD to an IEEE1394 port. (2) Go to playback mode by pressing the [Playback] button. (3) Press the [COPY] button.

(4) Run the “Backup Manager” by selecting the “Backup Data” menu.

(5) Set the backup range and press the “Start” button after selecting the backup HDD.

1. Backup HDDs should be formatted to the FAT32 type. 2. Backup data can be played on a PC with dedicated players such as SVR Manager or MiniPlayer. 3. Backup data is made as one “*.re3” file. If the file size is over 2GB, it may not be recognized normally because of the PC file system structure. 4. In the course of backup, the “Auto Delete” function doesn’t work. If the HDD is full, recording may be stopped instantly. 5. For more detailed information on the SVR Manager’s backup, please refer to the “SVR Manager User Guide”.

Samsung Techwin

2004. 07. 2001 (v 1.0)

59

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

1.3.2 Separating and Preserving HDDs HDDs with data on them can be kept separately only when the HDD is installed and used in the DVR (including the primary disk and RAID). It is recommended to use an external HDD rather than an internal HDD. In other words only connect one external HDD, and then keep it when it is full of data.

Data on preserved HDDs can only be played when the HDD is connected to the DVR.

1.3.3 Cautions For HDD handling or guarantees, apply to the after sales service of the HDD manufacturer. Any data losses caused by user error shall not be subject to the warranty.

60

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

2. Changing Video Type The SVR-1630 changes video type by automatically detecting the video signals. If there are no video signals, the SVR-1630 refers to the internal jumper status and indicates the type.

Jumper Setting

Video Type

1-2

NTSC Video

2-3

PAL Video

For changing the video type, contact your local vendor. If any problems occur due to unauthorized changes, the warranty is invalidated.

Samsung Techwin

2004. 07. 2001 (v 1.0)

61

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

3.

Using CD-Rom

3.1 CD- ROM DISC Components Installation Guide

: SVR-1630 Installation Guide

User Guide

: SVR-1630 User Guide

SVR Manager

: SVR Manager User Guide (SVR Remote Management Program)

Acrobat Reader

: Version 5.1

3.2 Preparation To read the User Manual in the CD-ROM Disc, Adobe Acrobat 5.0 should be installed in the client PC.

If Adobe Acrobat Reader is not installed in the client PC, use the CDROM’s Acrobat Reader program.

3.3 Reading the User Manual in CD-ROM Follow the steps below to read the User Manual in CD-ROM.

(1) Insert the CD-ROM supplied into the PC’s CD-ROM drive (2) Open the user guide PDF file.

62

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

4.

SVR-1630

Specification

General CPU

32bit RISC Processor (266MFPS)

Flash Memory

8MB

Main Memory

128MB

Boot Memory

64KB

OS

Embedded LINUX

Video Input Channel

16 Analog Channel

Compatible

Auxiliary

Storage Internal 3.5” IDE HDD 2EA (default 1EA)

Devices

Internal 3.5” IDE HDD RACK 1EA or CD-RW 1EA External 2EA for IEEE-1394 SBP2 compatible (Supports Max. 4Tbytes )

File System

Data-loss protection against power failure

Monitoring Monitor A

30fps (NTSC), 25fps (PAL) per channel 1,4,9,16,13 Channel, Fixed & User Defined Sequence

VGA

640x480@60, 800x600@60, 1024x768@60 (Monitor A Output)

Monitor B

30fps (NTSC), 25fps (PAL) 1 Channel, Fixed & User Defined Sequence Menu setting not available, except for playback and channel information

Recording and Playback Compression Method

WISE (Differential Wavelet)

Recording Speed

Up to 30ips per channel, total 240ips (NTSC) Up to 25ips per channel, total 200ips (PAL)

Resolution

720x243 (NTSC) 720x288 (PAL)

Image Quality

5 steps. Adjustable by channel. Combining frame rate and quality. Low/Normal/High/Custom setting

Playback Speed

Max. 60fps in Monitor A or Monitor B

Playback Method

1/2x2/3x3/4x4 Split Screen on Monitor A,1 Channel on Monitor B 1x, 2x, 4x, 8x, 16x , 32x (Forward & Reverse Play)

Image Search

Time : Year/Month/Date/Time/Minute Event : Search in Event Log Step-Forward, Step-Reverse

Samsung Techwin

2004. 07. 2001 (v 1.0)

63

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

Network Dedicated Program

SVR Manager

Protocol

TCP/IP, ARP, ICMP, DHCP, PPPoE

Connector

10/100Mbps Ethernet (RJ-45)

SW Upgrade

Firmware upgrade via Network

Simultaneous Users

1 Admin 10 Users :

Monitoring (Max. 5 Users) Playback (Max. 5 Users)

Security

Password (User or Administrator Authenticantion)

Environment Operating Temperature

5~40℃

Storage Temperature

-10~50℃

Operating Humidity

30~80%, free of condensation

Storage Humidity

93% below, free of condensation

Data Backup/Expansion/Copy Data Backup

Internal HDD Rack or external IEEE-1394 SBP2 compatible HDD (FAT32 formatted) Internal CD-R or External IEEE-1394 CD-R, 700MB CD-R

Data Copy

USB(1.1), 1 Channel Data + Miniplayer

Analogue VCR

VHS Video output for VCR

Backup Reminder

Daily / Weekly / Monthly

PTZ Control Available Serial Ports

RS232 (2), RS422/485 (2)

Control Method (Local)

Front panel button & IR remote controller (controls IP video channel as well)

Control Method (Remote)

On-screen PTZ control on PC

Preset Mode

16 points preset per channel

Group Mode

1 group per channel

64

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

SVR-1630

Input/Output Video

Input Level : 0.5 ~ 2.0 Vp-p 2 BNC , S-VHS and VGA output for Monitor A 1 BNC output for Monitor B 16 Loop through video

Audio

1 Input : Line-in, 1 Vpp 1 Output : Line-out, 1Vpp Level : -7~8 (16 Step) Record level AMP : 20dB amplifier for low level audio Monitoring : Local and remote

Relay Output

4 Relay outputs (Max DC 30W, AC 62.5VA)

Relay Output Schedule

Daily : Day / Night Weekly : Weekdays / Weekends Conditions : MD, Sensor inputs

Sensor Input

16 Sensor inputs (Supports Dry contact)

Serial Port

Terminal : 1 RS-485 /422 (PTZ control, Max. 384Kbps) RJ-45 : 1 RS-485 /422 (Keyboard interface) 1 RS-232C (PTZ or DVR chain ) 9Pin D-SUB : 1 RS-232C (Text input , Max. 230Kbps H/W Flow control)

Additional Functions Digital Zoom

2x (Live & PlayBack Mode)

Alarm Notice

MD, Vloss, Sensor, Text

Alarm Data Preservation

Event triggered Video Data Preservation

Alarm Log

Log search Log monitoring via OSD & Network

Pre/Post Alarm Recording

Pre : 1~10 seconds Post : 1~60 seconds

Schedule Recording

Daily : Day / Night Weekly : Weekdays / Weekends Conditions : Schedule / Event

Text Data Storage

POS/ATM

transaction

information

archived

along

with

corresponding video data

Samsung Techwin

2004. 07. 2001 (v 1.0)

65

SVR-1630

오류! 스타일이 정의되어 있지 않습니다.

Others Power Supply

AC 100V - 240V, (50/60Hz), Max. 2A

Power Consumption

Typical 75W (with 1 internal HDD)

External Dimensions Size (WⅹDⅹH)

420.0 x 440.10 x 92.5

Weight

8.3 Kg (with one HDD, one HDD Removable Rack)

66

2004. 07. 2004 (v 1.0)

Samsung Techwin

오류! 스타일이 정의되어 있지 않습니다.

Samsung Techwin

2004. 07. 2001 (v 1.0)

SVR-1630

67