Eurocode 8: Design of structures for earthquake resistance

Eurocode 8: Design of structures for earthquake resistance Edmund Booth, Consulting Engineer Introduction The six Parts of EN  1998 form a comprehens...
Author: Leon Harrington
38 downloads 0 Views 439KB Size
Eurocode 8: Design of structures for earthquake resistance Edmund Booth, Consulting Engineer

Introduction The six Parts of EN  1998 form a comprehensive set of requirements that provide a unified approach to the seismic design of structures and their foundations. The stated purpose of EN  1998 is to ensure that in the event of earthquakes: • human lives are protected; • damage is limited; and • structures important for civil protection remain operational. EN 1998 covers not only building structures, but also bridges and other facilities such as chimneys, towers, tanks and pipelines (both buried and above ground). Dams, offshore structures, nuclear power stations and long span suspension bridges are however specifically excluded from its scope. Table 8.1 shows the different parts of EN 1998 and the years of publication of the UK national annexes, which are available for all Parts except Part 3. Part 1 (EN 1998-1) contains general material applicable to all types of structure covered by EN 1998, including the definition of seismic actions. Part 1 also contains the main rules specific to the design of building superstructures in concrete, steel, steel–concrete composite, timber and masonry. The use of base isolation bearings to provide seismic protection is also covered by Part 1. Part 5 covers geotechnical matters, including the design of foundations, and therefore, like Part 1, applies to all ground supported structures. Parts 2, 4 and 5 provide additional rules for specific structural types other than buildings. Part  3 of EN  1998 deals with the assessment and retrofit of existing buildings, which is an important issue for seismic regions of the world, where

171

This complimentary chapter is brought to you by Eurocodes PLUS our online tool that helps with the Eurocodes transition, for more details go to: http://shop.bsigroup.com/transition © BSI British Standards Institution

The essential guide to Eurocodes transition Table 8.1. The six Parts of EN 1998 – Design of structures for earthquake resistance Part of Eurocode 8

Year of issue of UK national annex

EN 1998-1: General rules, seismic actions and rules for buildings: Section 1: General Section 2: Performance requirements and acceptance criteria Section 3: Ground conditions and seismic action Section 4: Design of buildings Sections 5–9: Specific rules for buildings in concrete, steel, composite steel–concrete, timber and masonry Section 10: Base isolation EN 1998-2: Bridges

2009

EN 1998-3: Assessment and retrofitting of buildings

None proposed

EN 1998-4: Tanks, silos and pipelines

2008

EN 1998-5: Foundations, retaining structures and geotechnical aspects

2008

EN 1998-6: Towers, masts and chimneys

2008

there are many buildings for which construction predated modern seismic design codes or where the general quality of historic infrastructure is seismically inadequate. No UK national annex is proposed for Part 3 because it was considered insufficient use would be made of it for structures in the UK which lay within the scope of EN 1998. As can be seen from Table  8.1, EN  1998 provides a unified approach to the seismic design of a very wide range of structural types and construction materials. It covers the selection of design ground motions, seismic analysis, special seismic detailing requirements and geotechnical issues such as design of retaining walls and assessment of the liquefaction potential of soils. EN  1998 is of course fully integrated with the rest of the Eurocode suite, to which reference is needed for non-seismic aspects of design. The comprehensive scope of EN 1998, and its ability to form part of a uniform basis for all aspects of design, is an important feature of the code which will be of benefit to UK designers. The clear and rational basis for its

172

This complimentary chapter is brought to you by Eurocodes PLUS our online tool that helps with the Eurocodes transition, for more details go to: http://shop.bsigroup.com/transition © BSI British Standards Institution

Eurocode 8: Design of structures for earthquake resistance

provisions and the advanced nature of many of its procedures will also assist designers.

Use of EN 1998 for design of structures in the United Kingdom Requirements for seismic design in the UK Seismic design has not previously been required for the great majority of UK structures and the introduction of EN 1998 does not change this. All the UK National Forewords to EN 1998 state: ‘There are generally no requirements in the UK to consider seismic loading, and the whole of the UK may be considered an area of very low seismicity in which the provisions of EN  1998 need not apply. However, certain types of structure, by reason of their function, location or form, may warrant an explicit consideration of seismic actions. Further guidance on the circumstances where an explicit seismic design should be considered is provided in PD 6698:2009.’ The UK national annexes to EN 1998 advise that an assessment of the need for seismic loading should only be carried out for consequence category CC3 structures. These are defined in EN 1990 Table B.1 as structures where failure would lead to high consequences for human life, or considerable environmental, social or economic impact. However, for many category CC3 structures, the recommended assessment is likely to conclude that an explicit seismic design is not required. The need for seismic design will depend upon the consequences of seismically induced failure, the level of seismicity at the site in relation to the UK average and the presence or absence of structural features known to be unfavourable for seismic resistance. Semi-quantitative guidance on these choices is provided in PD 6698:2009 (see next section), but it is recognized that much will depend on judgement. PD 6698:2009 advises that structures in consequence categories CC1 and CC2 are ‘unlikely to warrant seismic design, provided they are adequately designed for non-seismic design conditions’. These are structures where the consequences of loss are low or medium, and their seismic resistance can be considered as adequately covered by the robustness provisions of the non-seismic parts of the Eurocodes.

173

This complimentary chapter is brought to you by Eurocodes PLUS our online tool that helps with the Eurocodes transition, for more details go to: http://shop.bsigroup.com/transition © BSI British Standards Institution

The essential guide to Eurocodes transition

Published Document PD 6698:2009 – Recommendations for the design of structures for earthquake resistance to BS EN 1998 PD 6698:2009 is a background paper that gives non-contradictory, complementary information on the use of EN  1998 for the seismic design of UK structures. Although published by BSI, it does not have the status of a British Standard. PD 6698 contains a seismic hazard zoning map of the UK which the UK national annexes to EN  1998 permit as one option for obtaining ground motions for use in seismic design. An alternative option given by the UK national annex is to undertake a site specific hazard analysis; the UK national annex to Part 4 requires such analysis for the design of petrochemical facilities associated with large risks to the population or the environment. PD 6698 also provides advice on the circumstances in which seismic design may be warranted for buildings, bridges, tanks, pipelines, chimneys and towers in consequence category CC3.

Seismic design of nuclear facilities, dams and offshore structures Nuclear power plants are a prime example of ‘high consequence of failure’ structures, and have been designed seismically in the UK since the 1980s; major dams have also been subject to seismic assessment for many years as have offshore structures. However, these types of structures are specifically excluded from the scope of EN  1998 because there are particular aspects of their regulatory and detailed design performance that are not covered. Notwithstanding this, many features of EN 1998 are still relevant, and it is likely that EN 1998 will influence the practice of UK designers undertaking nuclear dam and offshore design work in the future.

Seismic design of bridges and petrochemical facilities Certain petrochemical facilities, such as liquid natural gas (LNG) tanks and high pressure gas pipelines, and important bridges are examples of other types of UK structures where seismic design has sometimes been carried out in the past, and EN 1998 covers seismic aspects of their design. EN 1998-2 covers the seismic design of bridges. PD 6698:2009 gives advice on the circumstances where seismic design needs to be considered for important

174

This complimentary chapter is brought to you by Eurocodes PLUS our online tool that helps with the Eurocodes transition, for more details go to: http://shop.bsigroup.com/transition © BSI British Standards Institution

Eurocode 8: Design of structures for earthquake resistance

UK bridges, and identifies the sections of EN 1998-2 which are applicable in the UK. Many of the provisions of EN 1998-2 do not apply to bridge design in low seismicity regions such as the UK; the main requirement is to carry out a seismic analysis and to check that the forces and deflections that this predicts are within the strength and deformation capacity of the bridge. The special seismic detailing provisions in EN 1998-2 are not generally required, as they would be in an area of high seismicity. EN  1998-4 covers the seismic design of tanks and pipelines. Tanks are the only type of structures where seismic design was previously covered by British Standards. There are two current relevant British Standards. BS EN 1473:2007 covers onshore LNG installations; it refers to EN  1998-4 for the seismic design of tanks. BS  EN  14015:2004 covers certain types of flat bottomed tanks for storage of liquids at ambient temperature and above; this currently contains a seismic design procedure based on US practice of some time ago, but it is understood that a revision will be published shortly which replace this advice with a requirement to use EN 1998-4. PD 6698:2009 currently advises that EN 1998-4 should be used in place of the seismic provisions of BS EN 14015:2004.

Seismic design of buildings Generally speaking, the only UK buildings which have previously been seismically designed were those with a safety related function, for example in the nuclear industry. The introduction of EN 1998, together with the UK national annexes and PD 6698:2009, opens the possibility that a limited range of other types of buildings may warrant seismic design, although as noted above, the UK national annexes state ‘that the whole of the UK may be considered an area of very low seismicity in which the provisions of EN  1998 need not apply’ and so seismic design is not mandatory. An example of a consequence category CC3 building which might warrant seismic design is a hospital in a part of the UK shown by the seismic zoning map of PD 6698:2009 to have higher than average seismicity, and which is either sited on soft soils (which tend to amplify earthquake motions) or has some structural feature unfavourable to seismic resistance such as a weak or ‘soft’ ground storey. If seismic design were carried out, it would be similar to that described in the section for bridges as follows. That is, the main requirement would be to carry out a seismic analysis and to check that the forces this predicts are

175

This complimentary chapter is brought to you by Eurocodes PLUS our online tool that helps with the Eurocodes transition, for more details go to: http://shop.bsigroup.com/transition © BSI British Standards Institution

The essential guide to Eurocodes transition

within the strength capacity of the building structure. The special seismic detailing provisions of EN 1998-1 would not generally be required.

Use of EN 1998 in areas of moderate to high seismicity worldwide Introduction The previous section applies to the special and rather unusual situations where EN 1998 is used for the seismic design of structures in the UK. It is expected that much more use will be made of EN 1998 by UK designers for seismic design of structures outside of the UK than within in it, for parts of the world where earthquakes provide a much more immediate threat. Within those countries adopting the Eurocodes, designs would of course need to make use of the relevant national annexes, rather than the UK national annex; these provide the seismic zoning maps needed for establishing design seismic loading and also the values of the Nationally Determined Parameters (NDPs). Advice on the application of EN 1998 to countries where a national annex does not exist is provided by the Institution of Structural Engineers/ AFPS Manual on EN 1998 [1]. Many UK engineers in the past have used US seismic codes for seismic designs internationally. EN  1998 has a number of features which are rather different from US practice. Broadly, the provisions of EN 1998 can be characterized as less empirical and more related to fundamental physics than the US counterparts, and in some places it may seem closer to an academic textbook than to the type of code provisions that UK engineers are used to. The common approach to a wide variety of structural types is an advantage over US provisions, as is the much greater provision of advice on geotechnical matters, given in EN 1998-5. The more rapid revision cycle in the US means that certain parts of current US codes can be regarded as more up to date; the EN  1998 Manual [1] gives advice on some circumstances where the provisions of EN 1998 may need upgrading. Generally, EN 1998 requires considerably greater lateral strength than do US codes for equivalent buildings. Subsequent paragraphs give a brief outline of some of the principal features of EN 1998.

176

This complimentary chapter is brought to you by Eurocodes PLUS our online tool that helps with the Eurocodes transition, for more details go to: http://shop.bsigroup.com/transition © BSI British Standards Institution

Eurocode 8: Design of structures for earthquake resistance

Analysis methods In common with most current seismic codes, ductility modified response spectrum analysis is the main type of analysis envisaged for buildings by EN 1998. The ‘behaviour factor’ q in EN 1998 is broadly equivalent to the ‘response modification factor’ R of the US International Building Code (IBC). The behaviour factor allows for the reduction in lateral strength requirement in structures that are designed to yield in a ductile manner during a major earthquake; the greater the degree of ductility that is available in the structure, the larger the q factor. Static pushover analysis, using displacement-based methods of analysis, is a more recent and precise way of allowing for post-elastic response. It is also presented in EN 1998, but not fully developed for new buildings in Part  1. However, complete methods are provided for bridges in Part  2 and for retrofitting buildings in Part  3. Time history and (briefly) power spectrum methods of analysis are also referred to.

An outline of some basic principles in EN 1998 for building design Design for different levels of ductility A well-established principle in earthquake engineering is the trade-off between strength and ductility; if collapse prevention and life safety preservation is the only concern, then for a given intensity of earthquake loading, a lower strength building can be designed, providing that the detailing ensures proportionately more ductility. EN 1998 allows the seismic designer to make such a trade-off by specifying two main classes of ductility provision, namely Ductility Class High (DCH) and Ductility Class Medium (DCM). The lateral strength requirement in DCM structures is 25% to 50% greater than in DCH structures. There are quite stringent seismic design and detailing requirements for both DCH and DCM structures, but they are more complex for DCH than DCM, particularly for concrete structures. Note that in US practice, ‘special’ ductility provisions are required for buildings in areas of high seismicity; generally, these ‘special’ provisions probably lie somewhere between those of DCH and DCM. A third, low-ductility class exists, Ductility Class Low (DCL), but this is not permitted for use in areas of moderate or high seismicity. DCL structures must be designed for essentially elastic response, using a q factor not

177

This complimentary chapter is brought to you by Eurocodes PLUS our online tool that helps with the Eurocodes transition, for more details go to: http://shop.bsigroup.com/transition © BSI British Standards Institution

The essential guide to Eurocodes transition

exceeding 1.5 (or 2 for some steel structures). However, after providing sufficient lateral strength to resist the seismic forces implied by q £ 1.5 (or q £ 2 in steel structures), almost no further specific seismic design and detailing measures are required, and design may proceed using the appropriate non-seismic Eurocodes. The reason for prohibiting DCL structures in areas of moderate or high seismicity is that they may fail in a brittle manner if loaded beyond their design strength. Since both the level of seismicity and seismic response are subject to great uncertainties, a high level of ductility is a good insurance policy; ductile structures, while they will be damaged by greater than expected earthquake motions, are much less likely to collapse and kill or injure their occupants than brittle structures. Capacity design measures (see section below) are an essential part of ensuring that this reserve of ductility is present.

Primary and secondary elements Primary elements are those which contribute to the seismic resistance of the structure. Some structural elements can however be designated as ‘secondary’ elements, which are taken as resisting gravity loads only. Their contribution to seismic resistance must be neglected. These elements must be shown to be capable of maintaining their ability to support the gravity loads under the maximum deflections occurring during the design earthquake. This may be done by showing that the actions (moments, shears, axial forces) that develop in them under the enforced compatible seismic deformations for the whole structure (determined by analysis) do not exceed their design strength, as calculated using Eurocode  2 or Eurocode  3. Otherwise no further seismic design or detailing requirements are required. Essentially, secondary elements are a type of low ductility element, which (unlike DCL elements) are not restricted to areas of low seismicity. Figure 8.1 shows two framing arrangements. In the grid frame, all the columns are primary elements, but in the perimeter frame, the internal columns are secondary elements. Thus, the perimeter frame is considered as the primary seismic resisting element, and is designed for high ductility while the internal members are considered secondary. This gives considerable architectural freedom for the layout of the internal spaces; the column spacing can be much greater than would be efficient in a moment resisting frame, while close spaced columns on the perimeter represents much less obstruction.

178

This complimentary chapter is brought to you by Eurocodes PLUS our online tool that helps with the Eurocodes transition, for more details go to: http://shop.bsigroup.com/transition © BSI British Standards Institution

Eurocode 8: Design of structures for earthquake resistance Internal beams and columns not taken as contributing to lateral resistance

(a)

(b)

Figure 8.1. Sectional plan on grid and perimeter frames. (a) Grid frame. (b) Perimeter frame

Ductile link

Brittle link

Figure 8.2. Concept of capacity design

Capacity design DCH and DCM structures must be checked by capacity design procedures to ensure that ductile yielding occurs before brittle failure. The principle is to ensure that the ductile regions yield first, thereby protecting the brittle regions from reaching their capacity. This is done by ensuring that brittle elements are designed to withstand a load which exceeds that induced by the yielding strength of the ductile links. The ductile links then act as a structural fuse, ensuring that the brittle links do not reach their capacity. This concept, developed by Professors Park & Paulay in Christchurch New Zealand in the 1970s, is illustrated schematically by the ‘ductile chain’ in Figure 8.2.

179

This complimentary chapter is brought to you by Eurocodes PLUS our online tool that helps with the Eurocodes transition, for more details go to: http://shop.bsigroup.com/transition © BSI British Standards Institution

The essential guide to Eurocodes transition Table 8.2. Recommended definitions of seismic zones in EN 1998 Zone

Peak ground acceleration (PGA) for 475 year return period

Seismic design requirements

Rock

Soil

High to moderate

> 8 %g

> 10 %g

Full seismic detailing to DCH or DCM

Low

8 %g ≥ PGA > 4 %g

10 %g ≥ PGA > 5 %g

DCL; q £ 1.5 (q £ 2 for steel) no seismic detailing

Very low

£ 4 %g

£ 5 %g

No seismic design required

Ensuring that columns are stronger than beams in moment frames, and that concrete frame members are stronger in shear than in flexure are two important examples of capacity design. The principle is simple, though the rules in EN 1998, particularly for concrete structures, can be quite complex. The capacity design principle is applied more widely than is the case for US seismic codes; for example, foundations must generally be checked to capacity design principles to ensure they can develop the yielding strength of the superstructures they support, which is not required by US codes.

Design for different levels of seismicity Three bands of seismicity are recognized by EN 1998, as follows. • high to moderate; • low; • very low. In high to moderate seismic zones, building structures should be designed with ‘high’ (DCH) or ‘medium’ (DCM) ductility; this involves full seismic detailing and capacity design procedures. In low seismicity zones, structures may be designed as ‘low’ ductility and special seismic detailing and capacity design requirements are waived. Seismic design is waived altogether in very low seismicity zones. The recommended definitions for the three zones given in EN 1998 are given in Table 8.2, although they can be modified for a particular country by its national standards authority. As noted previously, the UK national annexes to EN 1998 define the whole of the UK as being a zone of very low seismicity. 180

This complimentary chapter is brought to you by Eurocodes PLUS our online tool that helps with the Eurocodes transition, for more details go to: http://shop.bsigroup.com/transition © BSI British Standards Institution

Eurocode 8: Design of structures for earthquake resistance

Guidance material on EN 1998 The Designers’ Guide to EN 1998-1 and EN 1998-5 [2] gives background information and guidance on many aspects of EN 1998. It is one of a series of designers’ guides to the Eurocode suite. A manual on EN 1998 [1] has been prepared by the Institution of Structural Engineers and the Association Française du Genie Parasismique (AFPS – which is the French counterpart of the UK earthquake society SECED). It is intended as a stand-alone source for the requirements of EN 1998 for the majority of straightforward steel and concrete buildings, and in addition provides extensive guidance and design aids beyond those provided in EN 1998 itself. The manual gives the values of NDP recommended by EN 1998, as well as those given in the UK and French national annexes. Seismic zoning maps of the UK and France are provided. A textbook edited by Elghazouli [3] based on recent courses presented by SECED at Imperial College gives further information on structural and geotechnical aspects of EN  1998, and includes worked examples for the foundation and structural design of an example building, constructed in both concrete and steel. An article in the Structural Engineer [4] provides a briefing on EN 1998. A textbook by Booth and Key [5] makes extensive reference to the provisions of EN 1998.

References [1] Manual for the seismic design of steel and concrete buildings to EN 1998, Institution of Structural Engineers, London: 2009 [2] Fardis M., Carvalho E., Elnashai A., Faccioli E., Pinto P. and Plumier A. Designers’ guide to EN  1998-1 and 1998-5. EN  1998: Design Provisions for Earthquake Resistant Structures, Thomas Telford, London, 2005 [3] Elghazouli A. (editor) Seismic design of buildings to EN 1998, Spon Press, London, 2009 [4] Standing Committee on Implementation of Eurocodes. Eurocode 8 explained, The Structural Engineer, Vol. 87, No. 12, 16 June 2009, p15 [5] Booth E. and Key D. Earthquake design practice for buildings, Thomas Telford, London, 2006

181

This complimentary chapter is brought to you by Eurocodes PLUS our online tool that helps with the Eurocodes transition, for more details go to: http://shop.bsigroup.com/transition © BSI British Standards Institution

Suggest Documents