ESD flooring and covering ?
Which ESD-flooring do you need? A basic need for the floor is the resistance to ground RA. This should constitute less than 1 x 109 Ohm when measuring starts from the upper surface point of the flooring up to potential equalisation or ground terminal according to DIN EN 61340-5-1 (EBP). No ESDS has to be done on the flooring that’s why a lower limit is not quoted anymore. ESDS is transported in ESD cases or by persons who fulfill ESD requirements. If only ESD flooring/ESD shoes are used as grounding system, the resistance to ground including person, shoes and flooring has to amount < 3,5 x 107 Ohm. If a higher resistance is used for shoes or flooring systems, the resistance to ground has to be less than 1x 109 Ohm and the maximum voltage at a person does not fall below a limit of 100 V under worst case conditions. Are you working at open (i.e. easily accessible, tangible) dangerous voltages? YES: than you need a specific flooring which guarantees a minimized leakage resistance according to DIN VDE 0100-410 for persons safety of > 5 x 104 Ohm. The minimum value depends on the applied voltage.
!
Only when using ESD shoes and flooring in combination they will work in an optimal
?
What is the "Walking Test” for?
manner – using only ESD shoes or only ESD flooring will show almost no effect…
The new standard DIN EN 61340-4-5 (standard test method for particular applications – a procedure to characterize the electrostatic safety effect of shoes and flooring in combination with a person) describes a highly representative but also a very complex test to evaluate the static voltage of a person who moves on the test flooring. But the calculated data do only apply for a croncrete person including the specific shoe characteristics of this person. A generalisation means to make restrictions!
!
Regulary test your ESD flooring! Particularly during wintertime the flooring should be checked about its discharge capacity. Often heavy variations of requirements and reality are detected in practice. This has various causes, which range from improper cleaners to false grounding and from improper materials ("antistatic flooring”) to lost conductivity when using coverings containing epoxy casting resin with fibres for discharging.
?
You obtain a well-preserved flooring which is not – or not anymore dissipative? No problem. A long lasting, conductive and highly resistant top coat can be put on your floor with CANESOL ES II; CANESOL PV or POWERFLOOR.
>
Throughout Europe the ESD-compatible laying of floors is possible by the CANESPA flooring team! Call us and together we`ll (almost) always find a solution.
Tel: +32 (0)3 230 19 75
www.esdproducts.eu
Fax: +32 (0)3 230 19 78 9
ESD Industrial flooring POWERFLOOR POWERFLOOR is a robust and long lasting industrial coating – also clean room approved – and fulfills the requirements according to DIN EN 61340-4-1 and to the new standard DIN EN 61340-4-5. Due to a ESD covering layer of 0.5 to 3 mm or even more the well-prised flooring remains long lasting and resists forces properly.
Clean room approved
Is your floor coating e.g. a carbon fibres coating system in a good condition but does not meet the required technical data? Not only suitable for new flooring but can also be used for reconstructing utilized floor coatings. Application without removal of the existing coating is possible. In realtime even during the weekend.
Specification
Requirement
Performance of POWERFLOOR
Electrostatic charging at persons "Walking Test" max. 100 Volt DIN EN 61340-4-5 and EOS/ESD-STM 97.2 System resistance "person-shoe-flooring” DIN EN 61340-4-5 and EOS/ESD-STM 97.2 Resistance to ground DIN EN 61340-4-1 and ANSI/ESD S 7.1
< 10 Volt *) 12% rel. humidity
7,5 x 105 …3,5 x 107 Ohm
1,6 … 3,8 x 106 Ohm *)
< 109 Ohm
1 x 105 … 9,6 x 105 Ohm at 10V test voltages *) depending on the types of shoes used for the test, in this case CANESPA ESD shoes
POWERFLOOR ESD system modules: - Epoxy resin priming coat - Epoxy resin conductive layer - Epoxy resin ESD final coating
Advantages of POWERFLOOR: Reconstruction of utilized floor coatings
Polishing and new covering layer
Economic, thick layers
Thin and thick coating (self-spreading) Electrical features do not depend on the thickness of the coating
Humidity
no influence, because of the consolidated punctual conductive synthetic, not aqueous and humidity resistant
Free from alkyl, nonylphenol, softening agent and is water-based Highly abrasionproof Suitable for clean rooms when hardend (CANESPA ESD shoes on industrial flooring POWERFLOOR)
Tel: +32 (0)3 230 19 75 10
www.esdproducts.eu
Fax: +32 (0)3 230 19 78
Electrostatics Questions (management related)
How important is the question for you? very normal less none
yes
Actual status partly no
Are the ESD-measuring instruments (Tera-ohmmeter, field meter) available for the ESD co-ordinator? Is there a conductive flooring in ESD protected areas and is the grounding characteristic proved? Does anyone wear conductive shoes (ESD shoes) inside the ESD protected area? Are there conductive desktops of tables, shelves, racks and so on? Do you have conductive chairs? Are there conductive transport carts used and checked frequently? Are the ESDS and other protecting facilities as well as packaging clearly labeled? Does anybody wear ESD clothes (smocks, shirts etc.)? If packagings are opened while checked within stock receipt: Is there an ESD workstation seted up? Do you influence the selection of cleaning agents especially floor cleaning agents utilized of cleaners within the EPA? Notes on the testing questions: The questions are selected without any claim to be complete and without quality rating. Therefore the answering of these questions will only show a random sample of your ESD situation! Please answer the questions on a gut level, without long thinking and without extenuation – the result is just for you not for any other persons. The questioning form contains only "yes-questions”. If you can answer with yes – everything is allright. If there is no "yes” you have the option to check or to let check of reliable authorities if and what amount of importance this question does have on you and your associate partners. Value levels are set by yourself, e.g.: very = 5
normal = 3
less = 1
none = 0
and enable you to quantify your "NO"conclusions. Interesting is also to include further employees when answering questions and analysing results. This extends the observasion horizont and accidential occurrence is also excluded as well as the important is highlighted. Packaging badge example:
* main function - badge S (= shielding) D (= dissipative) L (= low charging) C (= conductive)
Device badge example:
shielding / shielding effect against electrostatic recharging electrostatic conductive – resistance to ground ≥ 1 x 105 Ω und < 1 x 1011 Ω marginal rechargeable (old term: antistatic) electrostatic conductive – resistance to ground ≥ 1 x 102 Ω und < 1 x 105 Ω
Tel: +32 (0)3 230 19 75
www.esdproducts.eu
Fax: +32 (0)3 230 19 78 7
ESD flooring New: ESD- flooring POWER-CONNECT POWER-CONNECT - a ESD flooring suitable for heavy load (suitable for forklifts tired with up to 5.0 t and elevating trucks up to1.5 t – depending on conditions). For easy floor laying and where you can step on right away. The flooring modules are
Makes loose laying on damaged, oily and ailing floors possible!
connected by a special invisible interlocking system shaped like a dove tail. Due to its unique assembly, electrial conductivity is guaranteed at a loosly laying for the first time.
Flipside is equipped with honycomb structure - this makes laying on floors with highly residual moisture possible, due to the achieved ventilation
Typical resistance to ground 105 to 106 Ohm DIN EN 61340-5-1 Simple and easy floor laying at going concern smell absorbing and without any dust Can be stepped and drived on immediately after laying, heavy load approved*) Non-slip and comfortable to stand and walk Reusable Invisible interlocking system – this way it can be heat–sealed, to meet highest hygenic requirements Easy mechanical cleaning for economic maintenance Load capacity:
fork lift (air tired) up to 5.0 t – (firm tired) up to 2.5 t / elevating truck up to 1.5 t Static: 50 kg/cm2 – dynamic: 90kg/cm2
Simple loose laying of the modules – even suitable for "problematic” grounding e.g. for reconstruction of: Highly frequented areas Areas which are highly skid approved Rooms with high residual moisture Temporary rebuilding Raised and hole floors Especially constructed galvanised ramp profiles or made of V2A adjust the height of the border to the covering thickness of 9.7 mm.
Tel: +32 (0)3 230 19 75 12
www.esdproducts.eu
Fax: +32 (0)3 230 19 78
ESD flooring New: ESD- flooring POWER-CONNECT Technical Data: Dimensions of modules:
610 x 610 mm
Thickness:
9,7 mm 2
Weight per m :
approx. 11,5 kg
Weight per module:
approx. 4,3 kg
Resistance to ground:
≤1 x 106 Ω , DIN EN 61340-5-1
Persons electric charging:
< 100 Volt, DIN EN 61340-4-5
Anti-slid:
R 9, DIN 51130
Fire resistance:
Bfl – S1, EN 13501-1
Sound absorbing improvement:
approx. 8 dB, EN 140-4/ISO 717-1
Recyclable:
yes
Resistance to chemicals:
highly resistant to acids, bases, oils, petrol, alcohol and terpentine substitute. Low resistance to other solvents as condiments (benzene), ester (ethyl acetate), ketones (acetone), chlorinated hydrocarbons. 5 modules (= 1,86 m2) per box
Content of packaging:
surface of Power-Connect
POWER-CONNECT can be supplied in 5 standard colours:
Order No: Colour:
30.129.10 Montblanc grey
Order No: Colour:
30.129.20 Pacific blue
Order No: Colour:
30.129.30 Kiwi green
Other coulours on demand Order No: Colour:
Tel: +32 (0)3 230 19 75
30.129.40 Gobi grey
Order No: Colour:
www.esdproducts.eu
30.129.50 Oasis beige
Fax: +32 (0)3 230 19 78 13
Floor Coverings Floor Covering CANO CB Electrostatic conductive "el” Coloured plastic covering with marbling CANO CB is an electrostatic conductive plastic floor covering with a resistance to ground of RA < 106 Ohm according to DIN EN 61340-5-1. The covering meets the fire protection
CANO CB is supplied in 9 standard colours:
requirements of the class B1 according DIN 4102, part1. With smooth surface. CANO CB can be laied loosely -a conductive conglutination is not neccessary. Thickness :
~ 2,0 mm
Dimensions:
~ 2 x 23 m ~ 610 x 610 mm (also suitable for double bottom elements 600 x 600 mm) 14
Order No: 30.120.55 Colour No: 1205
Order No: 30.120.60 Colour No: 1135
Order No: 30.120.65 Colour No: 1125
Order No: 30.120.70 Colour No: 1155
Order No: 30.120.75 Colour No: 1145
Order No: 30.120.85 Colour No: 1175
Order No: 30.120.90 Colour No: 1185
Order No: 30.120.95 Colour No: 1195
Floor Covering CANPLAN EL II
= 5,21 m2 in a cardboard box
Order No: 30.120.80 Colour No: 1165
CANO CB is supplied in 6 standard colours:
Electrostatic conductive "al” with double function Coloured plastic covering with marbling CANO CB is an electrostatic conductive plastic floor covering with double function: 1. Resistance to ground of RA ≥ 106 - ≤ 108 Ohm according to DIN EN 61340-5-1 for an optimal protection of components and devices.
Order No: 30.124.20 Colour No: 794
Order No: 30.124.10 Colour No: 790
Order No: 30.124.30 Colour No: 793
Order No: 30.124.40 Colour No: 795
Order No: 30.124.50 Colour No: 791
Order No: 30.124.60 Colour No: 792
2. Minimum isolation for persons safety according to VDE 0100 part 610 (leakage resistance of > 5 x 104 Ohm). The covering meets the fire protection requirements of category B1 according to DIN 4102, part 1. With smooth surface. CANPLAN EL II can be laied loosely a conductive conglutination is not neccessary. Thickness:
~ 2,0 mm
Dimensions:
~ 2 x 25 m ~ 610 x 610 mm (also suitable for double bottom elements 600 x 600 mm ) 14
= 5,21 m2 in a cardboard box
Tel: +32 (0)3 230 19 75 14
www.esdproducts.eu
Fax: +32 (0)3 230 19 78
Floor Coverings Floor Coverings CANPLAN CB 150 Electrostatic conductive "al” with dual purpose or Electrostatic conductive "el”. CANPLAN CB 150 can be supplied in two versions: SD-version with dual purpose: 1.
resistance to ground of 106 ≤ RA ≤ 108 Ohm according to DIN EN 61340-5-1 to protect components and devices optimally.
2.
minimized electrical isolation for persons safety according to VDE 0100, part 610, 4 Ri > 5 x 104 Ohm
EC-version: resistance to ground of RA 5 x 104 < R < 106 Ohm according to DIN EN 61340-5-1 Electrically conductive flooring in an ESD-protected area
Thickness:
2 mm
Dimensions:
610 x 610 mm (also suitable for double bottom elements 600 x 600 mm)
The covering meets the fire protection requirements of category B1 according to DIN 4102, part 1.
CANPLAN CB 150 is supplied in 6 standard colours
Colour: Colour No:
medium grey 205
Colour: Colour No:
light grey 201
Colour: Colour No:
brownish beige 203
Order No:
Design
Order No:
Design
Order No:
Design
30.127.20 30.128.20
SD-version EC-version
30.127.30 30.128.30
SD-version EC-version
30.127.40 30.128.40
SD-version EC-version
Colour: Colour No:
yellow beige 229
Colour: Colour No:
blue 222
Order No:
Design
Order No:
Design
30.127.50 30.128.50
SD-version EC-version
30.127.60 30.128.60
SD-version EC-version
Tel: +32 (0)3 230 19 75
www.esdproducts.eu
Colour: Colour No: Order No: 30.127.10 30.128.10
dark grey 207 Design SD-version EC-version
Fax: +32 (0)3 230 19 78 15
ESD Flooring CANESPA CB 412 Electrostatic conductive "el". Bicoloured caoutchouc covering in dot design. The only light, electrostatic flooring made of caoutchouc has a smooth surface with a resistance to ground of RA < 106 Ohm according to EN 61340-5-1. Patented composite structure. Hardly inflammable B1 according to DIN 4102, part 1. This floor covering can be laid loosley – a conductive conglutination is not necessary. Thickness: Dimensions:
2,5 mm ~ 1,22 x 12 m ~ 610 x 610 mm (also suitable for double bottom elements 600 x 600 mm) 12
= 4,44 m2 in a cardboard box
profile fitting dimensions: C + U ESD flooring in an EPA zone.
CANESPA CB 412 NFPA As special item also available in a version which meets the requirements of the NFPA (minimum quantity on demand).
CANESPA CB 412 is supplied in 5 standard colours
Order No: 30.100.10
Colour light grey
Colour No: 253
Floor mat type BM 412 Thickness:
2,5 mm
Dimensions:
1.200 x 2.000 mm
With 2 patent fasteners and 1 grounding cord Order No: 30.100.30
Colour platin grey
Colour No: 0257
Order No: 30.100.40
Colour water blue
Colour No: 1382
Order No: 30.100.96
Colour dust grey
Colour No: 1065
Tablemat type TM 412 Thickness:
2,5 mm
Dimensions:
600 x 1.000 mm
With 2 patent fasteners and 1 grounding cord Order No: 30.100.60
Order No: 30.100.80
Colour dust grey
Colour jade
Tel: +32 (0)3 230 19 75 16
Colour No: 1065
Colour No: 1380
Order No: 30.110.60
5 years guarantee for constant conductivity
www.esdproducts.eu
Colour dust grey
Colour No: 1065
5 years guarantee for the constancy of the indicated electric values according to our guarantee conditions (please request the conditions)
Fax: +32 (0)3 230 19 78
ESD floor grid ESD CANSTEP-Mat Static dissipative Anti-Fatigue material, for use in EPA's with hard floors, anti-skid and shock absorbent, improves worker comfort and productivity
Cross section through our ESD CANSTEP-mat with knobs Material:
nitrile cautchouc, conductive
Resistance to ground:
≤ 106 Ohm
Cross section through our ESD CANSTEP-mat with smooth surface
Oil- and coolant-repellent Structure:
dome cell or smooth
Bottom side:
knob profile
Thickness:
14 mm
Standard Dimension:
600 x 900 mm Flattened borders at all 4 sides
Special Dimensions:
in (almost) any dimension available on demand
Order No: 31.730.00 31.731.00 Other dimensions on demand
Bottom side: knob profile
Design: knob profile smooth profile
Dimension: 600 x 900 x 14 mm 600 x 900 x 14 mm
ESD Floor grids, Anti-Fatigue Anti-skid Material:
polyethylene, conductive
Resistance to ground:
≤ 106 Ohm
Dimension:
400 x 800 x 25 mm – extendable due to special interlocking system
The knop profile at the bottom side are constructed in such a way that cables on the floor can be fixed safety. Anti-skid and sound absorbing
Interlocking system
Order No: 32.500.00 32.500.10 32.500.20 Tel: +32 (0)3 230 19 75
Description: floor grid border grid edge grid www.esdproducts.eu
Dimension: 400 x 800 x 25 mm 400 x 120 x 25 mm 120 x 120 x 25 mm Fax: +32 (0)3 230 19 78 17
ESD ground marking tape and accessories ESD ground marking tape D-STRIPE, extremely tearproof Can be used instead of colouring Easy and fast to handle, can be driven on immediately Easy to clean and removable residuelessly Resistant to acids and bases, but not to solvents Easy to clean with water and soap Order No: 38.423.50 38.423.55 38.423.56 38.423.57 38.423.58 38.423.60 38.423.70
Colour yellow blue red white green yellow yellow
Width 50 mm 50 mm 50 mm 50 mm 50 mm 75 mm 100 mm
Length: 30,5 m Thickness: 1,4 mm
ESD ground marking tape Suitable for any ESD area
Cupreous adhesive tape Self-adhesive
ESD adhesive foil CANWAYS
Material: Width: Length: Order No:
Length: Width:: Thickness: Order No:
Length: Width:
25 m 1000 mm
Order No:
31.800.00
PVC 50 mm 33 m 38.425.09
Snap fastener
16,5 m 9,0 mm 0,1 mm 32.750.75
Snap fastener circlip pliers
Suitable to fix floor covering on used floors
CANTRON Antistatic ESD floor cleaner
Order No: 26.850.30 26.850.35 26.850.40 26.850.45 26.850.10 26.850.15
1)
2)
3)
4)
5)
6)
Size 3 mm 3 mm 4 mm 4 mm 10 mm 10 mm
Fig. 1) 2) 3) 4) 5) 6)
Type female male female male female male
Note: Female e.g. is the the snap fastener on the cable, male is the connection at the wrist band.
Tel: +32 (0)3 230 19 75 18
Content 10 Liter
CANTRON is an antistatic floor cleaner suitable for all ESD areas. Order No:
26.850.50
www.esdproducts.eu
Order No:
32.760.00
Fax: +32 (0)3 230 19 78