www.crh.com.au SOLUTIONS FOR TRADE
Lighting Products
www.crh.com.au SOLUTIONS FOR TRADE
CONTENTS Lighting Products Page 3 - 6 Page 7 - 8 Page 9 - 10 Page 11 - 12 Page 13 - 15 Page 16 Page 17
Cool Room & Freezer Room Lights LED Tubes Recessed Canopy Light Fluorescent Tube Covers & Leads Fluorescent Lights Heat Lamps & Accessories UV Pest Control
LIGHTING PRODUCTS
SOLUTIONS FOR TRADE
Cool Room & Freezer Room Lights
www.crh.com.au
Bulkhead Waterproof Light Fitting
CODE
SF-200L
DESCRIPTION
IP65 Rated Bulkhead Light Fitting. Cast Aluminium Body, 280mm x 188mm x 100mm High. Supplied with 40w low energy lamp fitted.
3
LIGHTING PRODUCTS
SOLUTIONS FOR TRADE
Cool Room & Freezer Room Lights
www.crh.com.au
4
IP65 Twin LED Light Fitting
CODE
FH9236T8
DESCRIPTION
The CRH Eco-Series rated IP65 light fitting contains twin T8 1200mm 2835LED tubes containing 120 pcs, 5500-6500K, 1750 Lumens with inbuilt driver. 50,000 Hour Life. LED units start up instantly & emit very little heat, unlike traditional fluorescent tubes. This makes them ideal for use in cool rooms & freezers as they create less work for your refrigeration plant. The Working Temperature Range is -25º C to +50º C. • Long life • Energy efficient • Less maintainance • Save $$$
LIGHTING PRODUCTS
SOLUTIONS FOR TRADE
Cool Room & Freezer Room Lights
www.crh.com.au
IP65 Single LED Light Fitting
CODE
DESCRIPTION
FH9218T8
CRH ECO-Series IP65 rated waterproof single LED light fitting. 600mm Tube. 9W T8 with 60 2835 LED, 760 Lumens, AC90-260V. The Working Temperature Range is -25º C to +50º C.
FH9136T8
CRH ECO-Series IP65 rated waterproof LED light fitting. 1200mm Tube. 18W T8, 1520 Lumens. The Working Temperature Range is -25º C to +50º C.
5
(eg. garbage rooms) through the use of ozone by using the correct fused quartz sleeve. The Effect of the UVP GF600IM Germicidal Unit:When UVP Ultra Violet Germicidal Units are correctly 2 installed in a Cool Room, (one unit per 5 m ) they will dramatically reduce spoilage on the meat surface due to microbiological growth. Independent Research has shown that the shelf life of chilled meat can be successfully extended by the use of ultra violet light even at relative humidity’s of over 90%. Therefore bacteria and mould spoilage can be retarded while minimizing weight losses of stored product. This is particularly important for cool rooms where small cuts are stored for ready use. The extension of mutton storage life was clearly demonstrated by CSIRO's Food Science Laboratory, Cannon Hill, Qld, research. Investigation into the effects of Ultra Violet light on four carcasses at 2.8 degrees Celsius and 90% Relative Humidity showed that meat subject to ultra violet light had not even commenced to spoil even after 22 days storage. However meat not subject to ultra violet light had reached the end of its life after approximately 10 days.
LIGHTING PRODUCTS GF600IM Cool Room
SOLUTIONS FOR TRADE
Cool Room & Freezer Room Units Lights UVP ULTRA VIOLET’S GERMICIDAL UNITS INCREASE PROFITS BY: -
·
KILLING BACTERIA, VIRUS, YEASTS, AND MOULD SPORES THEREBY GREATLY REDUCING MICROBIOLOGICAL FOOD SPOILAGE
ULTRA VIOLET COOL ROOM GERMICIDAL· LIGHT
INCREASING FOOD STORAGE LIFE
· · · ·
HELPING TO PREVENT COOL ROOM ODOURS REDUCING FOODSTUFFS WEIGHT LOSS BY ALLOWING COOL ROOM OPERATION AT A HIGHER RELATIVE HUMIDITY REDUCING RUNNING COSTS BY ALLOWING COOL ROOM OPERATION AT A HIGHER TEMPERATURE GREATLY REDUCING THE NEED TO TRIM MEAT PROVIDING MAINTENANCE FREE OPERATION, THE LAMP IS GUARANTEED FOR ITS EFFECTIVE UV LIFE OF ONE YEAR
MEAT STORAGE & ULTRA VIOLET DISINFECTION The Reasons for Meat Spoilage: From the moment an animal is slaughtered, microscopic organisms start to contaminate the carcass and multiply at a rapid rate. It is these bacteria, yeasts and mould’s that cause odours and spoilage during storage. The surface of the carcass provides an extremely favourably food supply for these organisms which continue to develop and reproduce. (Under ideal conditions, once every 20 minutes) APPLICATIONS The UVP Germicidal units are used extensively in all areas where; meat, dairy products, fruit, vegetables, etc are stored or processed. These areas include all cool rooms, salad rooms, cheese storage, bottling lines and locations susceptible to airborne contamination.
CODE
GF600IM
www.crh.com.au
Bacteria population per cm2
6
Effect of Germicidal Ultra Violet Light on Storage Life of Meat
1000 MILLION 100 MILLION
END OF STORAGE LIFE
10 MILLION 1 MILLION 100,000 10,000 1000 100 0
4
8
11 Storage days
15
18
22
CRH AUSTRALIA 1-3 Nelson Street Moorabbin Victoria Australia 3189
Tel: 61 03 9532 1599 Fax: 61 03 9532 2696 Email:
[email protected]
DESCRIPTION
The mechanism of disinfection by Germicidal Ultra Violet (UV) light differs considerably from the mechanisms of chemical disinfectants such as alcohol, chlorine and ozone. Chemical disinfectants inactivate micro-organisms by destroying or damaging cellular structures, interfering with metabolism, and hindering biosynthesis and growth. Germicidal Ultra Violet (UV) light inactivates organisms by absorption of the 254 nm wavelength of light, which causes a photochemical reaction that alters Electrical Safety - Report No. 3096 SPECIFICATIONS: molecular components essential to cell function. As UV light penetratesDIMENSIONS: the cell wall of the micro-organism, the energy reacts with nucleic and other vital cell Model acids No.: GF600IM Length: 81 cm This GF600IM unit fully complies with Primary Voltage: 240 V, 50 Hz Width: 12 cm AS/NZS 3100:2002 including Amendments Primary Current: 22 mA 11 cm components, resulting in injury or death of the exposed cells therefore Height: making it impossible for them to replicate.1,A2, micro-organism thatPrimary cannot replicate, cannot infect a Wattage: 20.7 W &3 Shipping Weight: 5.5 kg Mounting: Ceiling or Wall General requirements for Electrical Equipment host.
LIGHTING PRODUCTS
LED Tubes
SOLUTIONS FOR TRADE
www.crh.com.au
7
LED Tubes
Each LED Tube has a Working Temperature Range from -25º C to +50º C. CODE
DESCRIPTION
NOTE
CF002
600mm LED Tube, 9W, 760lm, 90-264V AC 5500-6500K
Follow our simple instructions and turn your existing T8 fluorescents into an energy efficient long life alternative.
CF004
900mm LED Tube, 13W, 1250lm, 90-264V AC 5500-6500K
Follow our simple instructions and turn your existing T8 fluorescents into an energy efficient long life alternative.
CF006
1200mm LED Tube, 16W, 1520lm, 90-264V AC 5500-6500K
Follow our simple instructions and turn your existing T8 fluorescents into an energy efficient long life alternative.
CF007
1500mm LED Tube, 20W, 1900lm, 90-264V AC 5500-6500K
Follow our simple instructions and turn your existing T8 fluorescents into an energy efficient long life alternative.
LIGHTING PRODUCTS
LED Tubes
SOLUTIONS FOR TRADE
8
www.crh.com.au
How To Convert A T8 Light Fitting To An Energy Efficent LED Light Fitting Important Notice
Changes to electrical wiring should only be performed by a qualified Electrician. Installation Steps
• • • • •
Turn of the electricity supply before installation. A1 shows standard wiring for Fluorescent Fittings. Remove Ballast & Starter. Replace Starter wuth 250v HRC type Fuse. Wire as shown in B1 Insert LED tube
After
Before Remove the Magnetic Ballast,and then rewire it
Magnetic Ballast PIN 3
PIN 1
A1
PIN 2
LED TUBE PIN 4
LED TUBE
PIN 1
B2 B1
PIN 2
-
+ -
STARTER
L AC INPUT
N
Starter Replacement (HRC Fused)
Remove the traditional starter and then re-wire rewire itit including a HRC Fuse.
L
N
PIN 3 PIN 4
LIGHTING PRODUCTS
SOLUTIONS FOR TRADE
Recessed Canopy Light
www.crh.com.au
9
Recessed Canopy Lights
CODE
DESCRIPTION
404111320
Recessed canopy light. Length: 900mm (3ft) Watts: 60W Lamps included: 2 x 30W. Cut Out Required: 960 x 236mm
404111420
Recessed canopy light. Length: 1200mm (4ft) Watts: 72W Lamps included: 2 x 36W. Cut Out Required: 1260 x 236mm
FEATURES
8.76mm Laminated Glass consisting of 3 layers: Layer 1: 4mm Clear Toughened Glass Layer 2: 0.76mm White Translucent PVB Layer 3: 4mm Clear Toughened Glass Extruded stainless steel face plate. 3mm reinforced glass diffuser. Designed for canopy hood installation. All units furnished with mounting brackets. Waterproof, heatproof and greaseproof construction.
LIGHTING PRODUCTS
Recessed Canopy Light
SOLUTIONS FOR TRADE
www.crh.com.au
10
LED Recessed Canopy Light
CODE
DESCRIPTION
MATERIAL
K1815000010
Kason 22W LED Canopy Light Fitting.
Stainless Steel with Tempered Glass
260mm x 260mm, 110-277VAC, 50/60Hz, 3000K
No Ultraviolet Emission means that it does not attract insects; 1150 total Lumens; 80% of all available light is projected onto the work surface. Where other ambient light is present fittings should be located at 1200mm centres. 3 Year Limited Warranty.
LIGHTING PRODUCTS
SOLUTIONS FOR TRADE
Fluorescent Tube Covers & Leads
www.crh.com.au
Fluorescent Tube Cover
CODE
DESCRIPTION
MATERIAL
M1640
Fluorescent tube cover. Length: 600mm
PVC
M1643
Fluorescent tube cover. Length: 900mm
PVC
M1642
Flourescent tube cover. Length: 1200mm
PVC
M1641
Flourescent tube cover. Length: 1500mm
PVC
11
LIGHTING PRODUCTS
SOLUTIONS FOR TRADE
Fluorescent Tube Covers & Leads
Fluorescent Tube Lead
CODE
M1640A
DESCRIPTION
Fluorescent tube lead. Length: 3000mm
www.crh.com.au
Fluorescent Tube End Cap
CODE
M1644
DESCRIPTION
Fluorescent tube cover end cap Plastic.
12
LIGHTING PRODUCTS
Fluorescent Lights
SOLUTIONS FOR TRADE
www.crh.com.au
A Series Linear Light Fittings
CODE
A470-15 A625-18 A930-30 A1230-36 A1530-58 A1800-58 A2100-3030 A2400-3036 A2700-3636 A3000-5836 A3600-5858
DESCRIPTION
A Series Fluorescent Light 1 x 15W – 470mm A Series Fluorescent Light 1 x 18W – 625mm A Series Fluorescent Light 1 x 30W – 930mm A Series Fluorescent Light 1 x 36W – 1230mm A Series Fluorescent Light 1 x 58W – 1530mm A Series Fluorescent Light 1 x 58W – 1800mm A Series Fluorescent Light 2 x 30W – 2100mm A Series Fluorescent Light 1 x 30W & 1 x 36W – 2400mm A Series Fluorescent Light 2 x 36W – 2700mm A Series Fluorescent Light 1 x 58W & 1 x 36W – 3000mm A Series Fluorescent Light 2 x 58W – 3600mm
Description: ‘A’ Series fluorescent light Fitting. Flexible polycarbonate diffuser Finish Options: • Anodised Matt Silver (Standard) • Anodised Bright Dip Silver Custom lengths available on request.
13
LIGHTING PRODUCTS
Fluorescent Lights
SOLUTIONS FOR TRADE
www.crh.com.au
B Series Linear Light Fittings
CODE
B600-10 B750-15 B900-18 B1200-30 B1500-36 B1850-58 B2100-1830 B2400-3030 B2700-3036 B3000-3636 B3300-3658 B3600-5858
DESCRIPTION
B Series Fluorescent Light 1 x 10W – 600mm B Series Fluorescent Light 1 x 15W – 750mm B Series Fluorescent Light 1 x 18W – 900mm B Series Fluorescent Light 1 x 30W – 1200mm B Series Fluorescent Light 1 x 36W – 1500mm B Series Fluorescent Light 1 x 58W – 1850mm B Series Fluorescent Light 1 x 18W & 1 x 30W – 2100mm B Series Fluorescent Light 2 x 30W – 2400mm B Series Fluorescent Light 1 x 30W & 1 x 36W – 2700mm B Series Fluorescent Light 2 x 36W – 3000mm B Series Fluorescent Light 1 x 36W & 1 x 58W – 3300mm B Series Fluorescent Light 2 x 58W – 3600mm
Description: CODE DESCRIPTION 'B' Series fluorescent light Fitting. Flexible polycarbonate diffuser Finish Option: • Anodised Matt Silver (Standard) • Anodised Bright Dip Silver Custom lengths available on request.
14
LIGHTING PRODUCTS
SOLUTIONS FOR TRADE
Fluorescent Lights
www.crh.com.au
15
T8 Strip Lights
CODE
DESCRIPTION
SFE-10CS T8 Single Lamp Fluorescent with cord set. 10 Watts • Dimensions - Length 412mm x Width 36mm x Height 74mm • Cable Length - 1800mm
Features •Electronic ballast •Complies with minimum energy performance standards •Individually switched Technical Data •Uses standard T8 Triphos Lamp •5000k •230-240 Volt
SFE-15
T8 Single Lamp Fluorescent Series. 15 Watts • Dimensions - Length 520mm x Width 36mm x Height 66mm
SFE-15
T8 Single Lamp Fluorescent Series. 18 Watts • Dimensions - Length 670mm x Width 36mm x Height 66mm
SFE-30
T8 Single Lamp Fluorescent Series. 30 Watts • Dimensions - Length 975mm x Width 36mm x Height 66mm
SFE-36
T8 Single Lamp Fluorescent Series. 36 Watts • Dimensions - Length 1280mm x Width 36mm x Height 66mm
Important: These are NOT a waterproof fitting. Moisture or cold temperatures may affect the electronics. Electronic Control Gear - must NOT be installed on a circuit with inductive loads.
LIGHTING PRODUCTS
Heat Lamps & Accessories
SOLUTIONS FOR TRADE
AH Series Heat Lamps
Accessories C
A
B D
CODE
DESCRIPTION
A
‘AH’ Series heat lamp.
Choice of anodised finishes: Matt Silver, Matt Gold or Bright Dip Silver.
AH600-1500J
AH Series Heat Lamp 1 x 500W QH Lamp – 600mm
AH1200-2500J
AH Series Heat Lamp 2 x 500W QH Lamp – 1200mm
AH1500-3500J
AH Series Heat Lamp 3 x 500W QH Lamp – 1500mm
AH1800-4500J
AH Series Heat Lamp 4 x 500W QH Lamp – 1800mm
AH2100-4500J
AH Series Heat Lamp 5 x 500W QH Lamp – 2100mm
Custom lengths available on request.
B
EMCA10
EMCA20
R7s lamp holders 10A 250V M14 nut mount
C
QIR240300J
240V 300W QH Lamp R7s quick fit contacts jacketed
D
QIR240200J
200W Jacketed Heat Lamp 220mm long
QIR240300J118
300w Jacketed Heat Lamp 118mm long
R7S Lamp Holder, 10A 240V Flange mount
www.crh.com.au
16
LIGHTING PRODUCTS
UV Pest Control
SOLUTIONS FOR TRADE
I-Trap Ultra Violet Insect Trapper
CODE
www.crh.com.au
17
Packet of 10 Replacement Glueboards
DESCRIPTION
MATERIAL
IT60W
I-Trap Bug Trapper automatically and Silently Attracts, Kills & Collects flying insects in high risk and critical food preparation areas. • Continuous and economical operation • Low maintenance and costs • Suitable for all areas including food production to hospitality • Glueboards in trappers offer easy monitoring and identification of insects • IT60 trappers are approved for HACCP and QA applications • Tool-less servicing • All models feature shatterproof lamps
White Enamelled Steel
GB4325
GB4325 Black Glueboards are designed to suit the IT60W Ultraviolet Bug Trapper should be replaced every 4-6 weeks to ensure maximum effectiveness.
Black Adhesive Paper
www.crh.com.au SOLUTIONS FOR TRADE
1 Nelson Street, Moorabbin VIC 3189 AUSTRALIA Tel: 1300 274 287 Fax: 1300 274 329