TZ3200C ADSL Bridge/Router Ethernet Modem User’s Guide

TZ3200C ADSL Ethernet Modem User’s Manual

|Copyright | Copyrightⓒ Triz Communications Group All rights Reserved. No Part of this book shall be reproduced, stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without written permission from the publisher. The specifications and information regarding the products in this manual are subject to change without notice.

|Trademark Credit | Triz is registered trademark of Triz Communications Group. Windows is registered trademark of Microsoft Corp.

Triz Communications Group. 1F Oh-Bok Bldg, 279-23 Seongsu 2-ga 3-dong, Seongdong-gu, Seoul, Korea 133-832 Direct TEL:+82-2-2129-9200 Direct FAX:+82-2-2129-9292

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

2 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

Scope This guide describes the procedure to configure TZ3200C and the usages of the Web configuration pages.

Organization This guide is organized as follows:

Chapter 1 Introduction, introduces the TZ3200C ADSL Bridge/Router Ethernet modem, defines the scope of the document, and provides a brief overview of the functions of the Windows driver. Chapter 2 Installation and Setup, describes how to install TZ3200C ADSL Bridge/Router Ethernet modem. Chapter 3 Configuring the TZ3200C, provides the descriptions and usages for the TZ3200C ADSL Bridge/Router Ethernet modem‘s Web configuration pages. Appendix A Troubleshooting, describes some problems that you might have with the TZ3200C and how to isolate and possibly solve these problems. Appendix B Technical Specifications, lists the hardware and software specifications for the TZ3200C. Appendix C Factory Default Setting, lists the Factory default setting values of the TZ3200C.

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

3 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

Table of Contents Chapter 1

Introduction

……………………………….…… 5 ~ 8

1.1 Overview ……………………………………………………………... 1.2 System Requirement ..……………………………………………… 1.3 Important Safeguards ……………………………………………….

Chapter 2

Installations and Setup

.………………………

5 5 6

9 ~ 16

2.1 Unpacking the Box ……………………………………………….….. 9 2.2 Connectors & LED’s ……………….………………….…………….. 10 2.3 Installing the TZ3200C ……...…………………….………….. … 12

Chapter 3

Configuring the TZ3200C

.…………………

13 ~ 19

3.1 Before Configuration ………………………...……………………… 3.2 Logging on to the Web Console …………………………………... 3.3 Configuring the Router (PPPoA/PPPoE) Mode ………..………… 3.4 Configuring the Bridge (RFC 1483) Mode …………………………

Appendix A. Troubleshooting

14 15 16 18

.…………………………………… 20

Appendix B. Technical Specifications …………………………

21

Appendix C. Factory Default Setting

22

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

4 / 22

…………………….……

TZ3200C ADSL Ethernet Modem User’s Manual

Chapter 1 1.1

Introduction

Overview The TZ3200C ADSL Bridge/Router Ethernet Modem provides an “always-on” high speed Asymmetric Digital Subscriber Line (ADSL) connection to the telephone line. The TZ3200C solution hardware connects to the computer via the Ethernet interface. The TZ3200C supports T1.413-1998, G.dmt (G.992.1) and G.lite (G.992.2) ADSL and is designed to operate in LAN and WAN modes. In addition, the TZ3200C software includes the Web Server to support the feature of embedded graphics configuration for the TZ3200C products. Through the Ethernet connection, the end-user can identify the current configuration on the system.

1.2

System Requirements ☞ Windows 95 ☞ Windows 98 ☞ Windows 98SE ☞ Windows Millennium Edition ☞ Windows 2000 Home Edition & Professional ☞ Windows XP Home Edition & Professional ☞ Macintosh, Linux, UNIX

System Specification (Recommended). Internet speed depends on your system specification, so the following specifications are recommended. ⊙ OS : Windows 98/98SE or above ⊙ CPU :Pentium II 233MHz or higher ⊙ System Memory(RAM): 64MB or higher

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

5 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

1.3

Important Safeguards Read all the instructions carefully. Follow all warnings and instructions marked on the product. Environment y In-house stationary use, desktop or wall-mounted; the maximum ambient temperature may not exceed 45°C (113°F). y It must not be mounted in a location exposed to direct or excessive sunlight and/or heat radiation. y It must not be exposed to heat trap conditions and must not be subjected to water or condensation. y It must be installed in a Pollution Degree 2 environment. Qualified Personnel Warning Only trained and qualified personnel should be allowed to repair this equipment. Do not Dismantle the Product Dismantling this product can cause bodily injury and damage to the equipment because of electric shock, failure, misoperation and static electricity. Do not dismantle, repair or reassemble it without permission. Keeping the Installation Area Tidy The area of installation should be kept clean and tidy. Ensure also that no part of the device is placed where it could cause an accident. Cleaning Unplug this product from your computer before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Water and moisture Do not place this product near water, for example, near a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool. Remove Metallic Jewellery You must remove all your metallic jewellery including rings, necklace, and watch. Metallic objects are conductors of electricity when the power is on. It can cause serious burning and damage to the jewellery. Also, please avoid loose clothings and neckties because they can cause accidents and damage the device.

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

6 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

Ventilation Warning When you install the product, choose a well ventilated place in order to prevent product failure or misoperation due to overheating and dust causing data loss, product failure and human injury. Electromagnetic Wave Warning Electromagnetic wave has an adverse effect on the product/cable and causes abnormal operation by disorganizing the signal system. Therefore do not install or operate this product in a place where electromagnetic wave is present. Lightning Warning Lightning may bring about serious failures like product breakdown. In order to prevent damage from lightning, ensure that the place of installation and the connected cables are not susceptible to lightning. Installation of a surge suppressor system will minimize any danger of a lightning strike.  

Lightning Activity Warning Do not work on, connect or disconnect this product and cables during periods of lightning activity or when lightning is forecast.  

Ground Connected Cable Warning For all cables connected to the product, use ground connected cable to prevent or minimize problems from surge. Also do not touch any uninsulated part of cables disconnected from the product. Recommended Installation Range Warning In order to prevent falling off in performance caused by signal reduction, do not exceed the recommended installation range. Overheating Warning Unless you secure enough space around the device when installing it, heat coming out from other peripheral equipment affects the product and overheating can cause product failure or misoperation. Therefore always secure enough space around the place of installation to ensure that this does not happen. In order to prevent overheating of this unit, do not operate this product in an area where the temperature is 45℃(113℉) or above. Working Space Warning For easy maintenance and repair in case of problems , ensure that there is enough working space around the product. This helps to prevent overheating.

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

7 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

Modem / Telephone use y Avoid using a modem/telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. y Do not use the telephone to report a gas leak in the vicinity of the leak. y If telephone service is required on the same line and for optimum ADSL performance, distributed filters must be installed. Depending on your ADSL configuration and type of filters, installation must be carried out by qualified service personnel. y Consult your Telephone Company or ADSL Service Provider for instructions.

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

8 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

Chapter 2 2.1

Installation and Setup

Unpacking the Box Check the shipping carton carefully to ensure that the contents include the items you ordered.

ADSL Modem (1)

ADSL (Phone) Cable (RJ11 to RJ11) (1)

Direct UTP (LAN) Cable (RJ45 to RJ45) (1)

User’s Manual CD-ROM (1)

AC Power Adaptor (1)

External In-line Filter(1) (Option)

Note) The following hardware is not provided but is necessary to install and configure the TZ3200C. Before installing the TZ3200C, prepare the following hardware: y External Micro-filter or splitter (provided separately by your service provider)

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

9 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

2.2

Connectors & LED’s

TZ3200C (Front view) LED Operations LED

Colour

POWER LAN LINK

Green

Status - Solid - Off - Flashing - Solid - Flashing - Solid

DATA

- Flashing

PPP

- Flashing - Solid

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

Meaning - DC Power is being supplied to the TZ3200C. - Power Off - Data is transmitted or received to the LAN side - Ethernet interface is active.(100M/10M) - Trying to connect the ADSL line - ADSL line has synchronized with your service provider - Data is transmitted to the ADSL line - Trying to connect the PPP Mode - Solid green when using PPPoE or PPPoA, if the user has authenticated to the ISP’s server.

10 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

①

②

③

④

⑤

⑥

TZ3200C (Rear view)

Port Descriptions (Back Panel numbering from left side) Location

Label

Port

Function

①

ADSL

ADSL Line Port

Connects telephone Line cable to ADSL line.

②

PHONE

Telephone Port

Connects the telephone cable to your telephone.

③

CONSOLE

Console Port

(Not for User) Connects serial Console Cable

④

LAN

Ethernet port

Connects Ethernet cable from the LAN port in your PC.

⑤

DC6V 800mA

DC IN port

⑥

POWER

Power switch

Connects Adaptor TZ3200C Ethernet Power On/Off

When you connect the telephone cable in your telephone, Micro filter must be attached.

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

11 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

2.3

Installing the TZ3200C The TZ3200C is connected to any available Ethernet LAN port on the computer. There are no option switches for the user to set. Once the modem is connected to the Ethernet LAN port, connect the DSL line to the “ADSL” Port on the modem. < ADSL Modem Installation Diagram >

1. Connect the ADSL (Phone) cable provided to the wall and then connect the other end of the cable to the ADSL port of the TZ3200C. 2. Connect the LAN cable provided to the LAN port of the TZ3200C and then connect the other end of the cable to the Ethernet LAN port on your PC. 3. Connect one end of the AC power adapter to the DC6V800mA port of the TZ3200C and then plug the AC power adapter into a wall power socket.

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

12 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

Chapter 3

Configuring the TZ3200C

After you have properly installed the TZ3200C, if you need to change a modem setting for Router Mode or you want to review the current state of the modem, you can change the TZ3200C

settings with an ordinary web browser such as

Microsoft Internet Explorer. When the TZ3200C operates in router mode, you must change the modem setting: refer to the Router mode configuration table. The following table shows the typical configuration for using the TZ3200C in router mode. < Table 3.1 Mode Configurations > ADSL Service

Router Mode

Bridge Mode Configuration

WAN

Static IP

Dynamic IP

VPI/VCI

Enter the value provided by ISP

Enter the value provided by ISP

Enter the value provided by ISP

Static IP Address

N/A

N/A (Automatically Assigned by ISP)

Enter the value provided by ISP

Subnet Mask

N/A

N/A (Automatically Assigned by ISP)

Enter the value provided by ISP

Default Gateway

N/A

N/A (Automatically Assigned by ISP)

Enter the value provided by ISP

PPPoA VC-Mux / PPPoE LLC

1483 Bridged IP LLC

Enter the value provided by ISP N/A (Automatically Assigned by ISP) N/A (Automatically Assigned by ISP) N/A (Automatically Assigned by ISP) 1483 Bridged IP LLC

Encapsulation 1483 Bridged IP LLC

LAN

PPPoA / PPPoE

PPP User Name

N/A

Enter the name provided by ISP

N/A

N/A

PPP Password

N/A

Enter the password provided by ISP

N/A

N/A

DHCP Client

Disable

Disable

Disable

Enabled 192.168.1.1 (Default) 255.255.255.0 (Default)

IP Address

N/A

192.168.1.1 (Default)

Subnet Mask

N/A

255.255.255.0 (Default)

192.168.1.1 (Default) 255.255.255.0 (Default)

DHCP Server

Enable

Enabled

Enabled

Enabled

N/A

N/A (Automatically Assigned by ISP)

Enter the value provided by ISP

N/A (Automatically Assigned by ISP)

DNS

Note) When it is N/A, it means it does not apply to the encapsulation.

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

13 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

3.1

Before Configuration Before you configure the TZ3200C modem, you will need the following information: Connection Mode The connection mode your Internet Service Provider (ISP) is supporting. yBridge (RFC 1483) mode yRouter (PPPoA/ PPPoE) mode The default connection mode is PPPoA LLC. VPI/VCI The number of PVC your service provider is giving you together with their virtual path identifiers (VPIs) and virtual channel identifiers (VCIs). The default number of PVC is as follows: yVPI : 0 yVCI : 35 User ID and Password Point-to-Point Protocol (PPP) client name that is assigned as your login name and PPP password to access your ISP account. Check the Connection Status Before you configure the TZ3200C modem, check the connection status of your computer. Check the Power LED Check the Power LED is on.

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

14 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

3.2

Logging on to the Web Console Log on to the web console to configure the TZ3200C as follows: 1. Launch the web browser (ex. Internet explorer) installed in your PC. 2. Enter ‘http://192.168.1.1’ for the web console page in the browser locator field and press [Enter].

3. The following window appears for user authentication. Enter the user name “admin” and the password “telekomst” and click OK.

4. When the user authentication is successful, the web console home page appears.

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

15 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

3.3

Configuring the Router (PPPoA/PPPoE) Mode If your ISP supports the router (PPPoA/PPPoE) connection mode, configure the TZ3200C as follows: Note) This section describes only the parameters which have to be changed for the router mode. There is no need to change the parameter values that are not described in this section. To alter other parameter values, consult your service provider. 1. Click the Configuration Î WAN on the menu frame of the web console. 2. Click the Submit.

3. The page appears. Enter the following information and click Submit.

Select the “Bridged Enabled” Select the ADSL router service type of your ISP

Enter user login ID and password

Enter VPI and VCI value

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

16 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

Parameter

VPI

Description

Enter the VPI value specified by your ISP. The default VPI is ‘0’.

VCI

Enter the VCI value specified by your ISP. The default VCI is ‘35’. Select ADSL router service type supported by your ISP. ENCAPSULATION y PPPoA LLC : When your ISP provides the PPPoA service. y PPPoE LLC : When your ISP provides the PPPoE service. Username Enter the user login ID associated with ADSL connection. PPP Password Enter the user’s password.

3. To select whether you want to enable or disable DHCP, click the Configuration Î LAN on the menu frame of the web console. 4. The page appears. Left click in the DHCP Server combo box to Enabled and click Submit.

Select the Enabled

5. To apply changed configurations, click the Configuration Î Save Settings / Reboot on the menu frame of the web console. 6. The following page appears. Click Save & Reboot. After saving changed configurations, the modem will be restarted to apply it.

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

17 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

3.4

Configuring the Bridge (RFC 1483) Mode If your ISP supports the bridge (RFC 1483) connection mode, configure the TZ3200C as follows: 1. Click the Configuration Î WAN on the menu frame of the web console. 2. Click the Submit. 3. The page appears. Enter the following information and click Submit.

Select the “Bridged Enabled” Select the “1483 Bridged IP LLC”

Empty

Enter VPI and VCI value

Parameter

VPI

Description

Enter the VPI value specified by your ISP. The default VPI is ‘0’.

VCI

Enter the VCI value specified by your ISP. The default VCI is ‘35’. Select ADSL Bridge Mode BRIDGED y Enabled Select ADSL bridge service type supported by your ISP. ENCAPSULATION y 1483 Bridge IP LLC Username Empty PPP Password Empty

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

18 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

3. To select whether you want to enable or disable DHCP, click the Configuration Î LAN on the menu frame of the web console. 4. The page appears. Left click in the DHCP Server combo box to Enabled and click Submit.

Select the Enabled

5. To apply changed configurations click the Configuration Î Save Settings / Reboot on the menu frame of the web console. 6. The following page appears. Click Save & Reboot. After saving changed configurations, the modem will be restarted to apply it.

Note) When using Bridge Mode, you should install PPPoE client software (WinPoET, EnterNet300…Etc.). Please consult your service provider.

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

19 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

Appendix A. Troubleshooting If you cannot connect to the ADSL network, please check the status of the LEDs on the front panel, and then check the following: 1. Check the POWER LED If the POWER LED is not on, check to make certain that the AC power adapter is plugged securely into your computer. 2. Check the LINK LED If the LINK LED blinks continuously and never stays constantly on, ensure that the ADSL cable is firmly connected to the “ADSL port” on the TZ3200C . If the LINK LED still blinks, contact your ADSL service provider. If the LINK LED is not on, reconnect the TZ3200C to your computer using the USB Cable. If the LINK LED still blinks, contact your ADSL service provider. 3. Check your PC’s IP address If all LEDs operate normally and cables are firmly connected to the ports, ensure that your PC’s IP address is properly assigned. Your PC’s IP address setting must be dynamic IP (Obtain an IP automatically). Check the Network Neighbourhood (for Windows 9x) or My Network Places properties Æ Local Area connection’s properties. < Windows 2000 >

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

20 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

Appendix B. Technical Specifications Description

ADSL Compliance

Protocol Supported

Loop Length

Specification y Compliant with ADSL standards - Full-rate ANSI T1.413 Issue 2 - ITU-T G.992.1 (G.dmt) / ITU-T G.992.2 (G.lite) y DMT modulation and demodulation y Full-rate adaptive modem - Downstream: up to 8Mbps. Max - Upstream: up 1Mbps.max y Interoperable with all major DSLAM equipment - Annex A (ADSL over POTS) and Annex B (ADSL over POTS) y WAN mode support: - PPP over ATM (RFC 2364) - PPP over Ethernet (RFC 2516) y LAN mode support: - Bridged/ Routed Ethernet over ATM(RFC 1483) - Classical IP over ATM (RFC 1577) y ATM ALL5 (Adaptation layer type 5) y ATM SAR (Hardware SAR) y OAM F4/F5 y DHCP Server and Client y NAPT (Network address and port translation) - Dynamic NAT (Network address translation) Up to 18,000 feet (about 5.4km)

Security

y User authentication for PPP y PAP (password authentication protocol) y CHAP (challenge authentication protocol)

Interface

y Ethernet Interface: 10/100Base-T / RJ-45 y Modem Interface: ADSL Line / RJ-11 Phone Line / RJ-11

Operating System Support

Independent

Management & Configuration

TFTP / HTTP Web based

Environmental Requirements

y Operating Temperature: 0℃ ~ +45℃ y Operating Humidity: 10% ~ 90%

Power Requirement Dimension Weight LED Indicators

Input AC 230V/50Hz, Output DC 6V 800mA (U.K) 28mm(W) X 125mm(H) X 113mm(D) Max 178g POWER, LAN, (ADSL) LINK, (ADSL) DATA, PPP

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

21 / 22

TZ3200C ADSL Ethernet Modem User’s Manual

Appendix C.

Factory Default Setting Values ITEM

Values

VPI/VCI

0 / 35

Protocol

PPPoA LLC

Web console IP Address

192.168.1.1

Web Console ID Web Console Password

Doc. No. TZ3200C_MN_Ver1.0 Rev 0

admin telekomst

22 / 22