DEEP GROOVE BALL BEARINGS SINGLE-ROW DEEP GROOVE BALL BEARINGS Open Type, Shielded Type, Sealed Type
Bore Diameter 10 – 240mm ················· B8
Open Type
Bore Diameter 260 – 800mm ··············· B20
MAXIMUM TYPE BALL BEARINGS
Bore Diameter 25 – 11Omm ·············· B26
MAGNETO BEARINGS
Bore Diameter
4 – 20mm ················· B28
Extra Small and Miniature Ball Bearings are described on Pages B30 to B45.
DESIGN, TYPES, AND FEATURES SINGLE-ROW DEEP GROOVE BALL BEARINGS Single-Row Deep Groove Ball Bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings
Open Type
Shielded Type (ZZ Type)
B001-029E.indd 4-5
Shielded Type (ZZ Type)
Non-Contact Rubber Sealed Type (VV Type)
Torque
Low
Low
Higher than ZZ, VV types due to contact seal
Speed capability
Good
Good
Limited by contact seals
Grease sealing effectiveness
Good
Better than ZZ type
A little better than VV type
Dust resistance
Good
Better than ZZ type (usable in moderately dusty environment)
Best (usable even in very dusty environment)
Water resistance
Not suitable
Not suitable
Operating temperature (1)
–10 to +110°C
–10 to +110°C
With Snap Ring
Non-Contact Rubber Sealed Type (VV Type)
Contact Rubber Sealed Type (DDU Type)
B4
Type
Note
(1)
Contact Rubber Sealed Type (DDU Type)
Good (usable even if fluid is splashed on bearing) –10 to +100°C
The above temperature range applies to standard bearings. By using cold or heat resistant grease and changing the type of rubber, the operating temperature range can be extended. For such applications, please contact NSK.
B5
11/20/13 4:53:36 PM
For deep groove ball bearings, pressed cages are usually used. For big bearings, machined brass cages are used. (Refer to Table 2) Machined cages are also used for high speed applications. Table 2 Standard Cages for Deep Groove Ball Bearings Series 68 69 160
Pressed Steel Cages 6800 –
6838
6900 –
6936
16001 – 16026
Machined Brass Cages 6840 – 68/800 6938 – 69/800 16028 –
16064
60
6000 –
6040
6044 – 60/670
62
6200 –
6240
6244 –
6272
63
6300 –
6332
6334 –
6356
MAXIMUM TYPE BALL BEARINGS Maximum Type Ball Bearings contain a larger number of balls than normal deep groove ball bearings because of filling slots in the inner and outer rings. Because of their filling slots, they are not suitable for applications with high axial loads. BL2 and BL3 types of bearings have boundary dimensions equal to those of single-row deep groove ball bearings of Series 62 and 63 respectively. Besides the open type, ZZ type shielded bearings are also available. When using these bearings, it is important for the filling slot in the outer ring to be outside of the loaded zone as much as possible. Their cages are pressed steel.
MAGNETO BEARINGS The groove in the inner ring is a little shallower than that of deep groove ball bearings and one side of the outer ring is relieved. Consequently, the outer ring is separable, which makes it convenient for mounting. Pressed cages are standard, but for high speed applications, machined synthetic resin cages are used.
TOLERANCES AND RUNNING ACCURACY SINGLE-ROW DEEP GROOVE BALL BEARINGS ························································· Table 8.2 (Pages A60 to A63) MAXIMUM TYPE BALL BEARINGS ···················· Table 8.2 (Pages A60 to A63) MAGNETO BEARINGS ······································· Table 8.5 (Pages A70 and A71)
RECOMMENDED FITS SINGLE-ROW DEEP GROOVE BALL BEARINGS ························································· Table 9.2 (Page A84) Table 9.4 (Page A85) MAXIMUM TYPE BALL BEARINGS ···················· Table 9.2 (Page A84) Table 9.4 (Page A85) MAGNETO BEARINGS ······································· Table 9.2 (Page A84) Table 9.4 (Page A85)
INTERNAL CLEARANCES SINGLE-ROW DEEP GROOVE BALL BEARINGS ························································· Table 9.9 (Page A89) MAXIMUM TYPE BALL BEARINGS ···················· Table 9.9 (Page A89) MAGNETO BEARINGS ······································· Table 9.11 (Page A89)
LIMITING SPEEDS The limiting speeds listed in the bearing tables should be adjusted depending on the bearing load conditions. Also, higher speeds are attainable by making changes in the lubrication method, cage design, etc. Refer to Page A37 for detailed information.
PRECAUTIONS FOR USE OF DEEP GROOVE BALL BEARINGS For deep groove ball bearings, if the bearing load is too small during operation, slippage occurs between the balls and raceways, which may result in smearing. The higher the weight of balls and cage, the higher this tendency becomes, especially for large bearings. If very small bearing loads are expected, please contact NSK for selection of an appropriate bearing.
B6
B001-029E.indd 6-7
B7
11/20/13 4:53:36 PM
SINGLE-ROW DEEP GROOVE BALL BEARINGS Bore Diameter
Dynamic Equivalent Load P =X Fr +Y Fa
10 – 22 mm f
B
f 0 Fa
rN a
r
b
C 0r
r0
ra
r
ra
jD
jD 2
jd
jDa
0.172 0.345 0.689 1.03 1.38 2.07 3.45 5.17 6.89
ra jda jD X
jD 1
Open Type
Shielded Type ZZ
Basic Load Ratings
Boundary Dimensions (mm)
d
D
Non-Contact Sealed Type VV
(N)
B
r
Cr
Contact Sealed Type DD · DDU Factor
{kgf}
C 0r
Cr
C 0r
f0
12
15
17
20
22
Open Z · ZZ V · VV
DU DDU
Bearing Numbers
Oil Open Z
Open Shielded
Sealed
Snap Ring Groove Dimensions (1) With With Snap Snap Ring Ring Groove
(mm)
0.19 0.22 0.26 0.28 0.30 0.34 0.38 0.42 0.44
X 1 1 1 1 1 1 1 1 1
Y 0 0 0 0 0 0 0 0 0
Fa >e Fr X 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56
Y 2.30 1.99 1.71 1.55 1.45 1.31 1.15 1.04 1.00
Static Equivalent Load Fa >0.8, P0 =0.6Fr +0.5Fa Fr Fa ≤0.8, P0 =Fr Fr
CY
With Snap Ring NR
Limiting Speeds (min –1) Grease
min.
10
With Snap Ring Groove N
Fa ≤e Fr
e
Snap Ring (1) Dimensions (mm)
Mass
Abutment and Fillet Dimensions
(kg)
(mm)
a
b
D1
r0
rN
D2
f
max.
min.
max.
max.
min.
max.
max.
min.
d a(2)
D a(2)
ra
Dx
CY
max.
max.
max.
min.
max.
approx.
19 22 26
5 6 8
0.3 0.3 0.3
1 720 2 700 4 550
840 1 270 1 970
175 275 465
86 129 201
14.8 14.0 12.4
34 000 24 000 40 000 32 000 22 000 38 000 30 000 22 000 36 000
6800 6900 6000
ZZ ZZ ZZ
VV DD VV DD VV DDU
— — — N( 3) NR( 3) 1.05 N( 4) NR( 4) 1.35
— 0.80 0.87
— 20.80 24.50
— 0.20 0.20
— 0.2 0.3
— 24.8 28.7
— 0.70 0.84
12 12 12
12 12.5 13
17 20 24
0.3 0.3 0.3
— 25.5 29.4
— 1.5 1.9
0.005 0.009 0.018
30 35
9 11
0.6 0.6
5 100 8 100
2 390 3 450
520 825
244 350
13.2 11.2
24 000 18 000 30 000 22 000 17 000 26 000
6200 6300
ZZ ZZ
VV DDU VV DDU
N N
2.06 2.06
1.35 1.35
28.17 33.17
0.40 0.40
0.5 0.5
34.7 39.7
1.12 1.12
14 14
16 16.5
26 31
0.6 0.6
35.5 40.5
2.9 2.9
0.032 0.052
21 24 28
5 6 7
0.3 0.3 0.3
1 920 2 890 5 100
1 040 1 460 2 370
195 295 520
106 149 241
15.3 14.5 13.0
32 000 20 000 38 000 30 000 20 000 36 000 28 000 — 32 000
6801 6901 16001
ZZ ZZ —
VV DD VV DD — —
— — — N( 3) NR( 3) 1.05 — — —
— 0.80 —
— 22.80 —
— 0.20 —
— 0.2 —
— 26.8 —
— 0.70 —
14 14 14
14 14.5 —
19 22 26
0.3 0.3 0.3
— 27.5 —
— 1.5 —
0.006 0.010 0.019
28 32 37
8 10 12
0.3 0.6 1
5 100 6 800 9 700
2 370 3 050 4 200
520 695 990
241 310 425
13.0 12.3 11.1
28 000 18 000 32 000 22 000 17 000 28 000 20 000 16 000 24 000
6001 6201 6301
ZZ ZZ ZZ
VV DDU VV DDU VV DDU
N( 4) NR( 4) 1.35 N NR 2.06 N NR 2.06
0.87 1.35 1.35
26.50 30.15 34.77
0.20 0.40 0.40
0.3 0.5 0.5
30.7 36.7 41.3
0.84 1.12 1.12
14 16 17
15.5 17 18
26 28 32
0.3 0.6 1
31.4 37.5 42
1.9 2.9 2.9
0.022 0.037 0.060
24 28 32
5 7 8
0.3 0.3 0.3
2 070 4 350 5 600
1 260 2 260 2 830
212 440 570
128 230 289
15.8 14.3 13.9
28 000 17 000 34 000 26 000 17 000 30 000 24 000 — 28 000
6802 6902 16002
ZZ ZZ —
VV DD VV DD — —
— — — N( 3) NR( 3) 1.30 — — —
— 0.95 —
— 26.70 —
— 0.25 —
— 0.3 —
— 30.8 —
— 0.85 —
17 17 17
17 17 —
22 26 30
0.3 0.3 0.3
— 31.5 —
— 1.8 —
0.007 0.015 0.027
32 35 42
9 11 13
0.3 0.6 1
5 600 7 650 11 400
2 830 3 750 5 450
570 780 1 170
289 380 555
13.9 13.2 12.3
24 000 15 000 28 000 20 000 14 000 24 000 17 000 13 000 20 000
6002 6202 6302
ZZ ZZ ZZ
VV DDU VV DDU VV DDU
N N N
2.06 2.06 2.06
1.35 1.35 1.35
30.15 33.17 39.75
0.40 0.40 0.40
0.3 0.5 0.5
36.7 39.7 46.3
1.12 1.12 1.12
17 19 20
19 20.5 22.5
30 31 37
0.3 0.6 1
37.5 40.5 47
2.9 2.9 2.9
0.031 0.045 0.083
26 30 35
5 7 8
0.3 0.3 0.3
2 630 4 600 6 000
1 570 2 550 3 250
268 470 610
160 260 330
15.7 14.7 14.4
26 000 15 000 30 000 24 000 15 000 28 000 22 000 — 26 000
6803 6903 16003
ZZ ZZ —
VV DD VV DDU — —
— — — N( 3) NR( 3) 1.30 — — —
— 0.95 —
— 28.70 —
— 0.25 —
— 0.3 —
— 32.8 —
— 0.85 —
19 19 19
19 19.5 —
24 28 33
0.3 0.3 0.3
— 33.5 —
— 1.8 —
0.007 0.017 0.033
35 40 47
10 12 14
0.3 0.6 1
6 000 9 550 13 600
3 250 4 800 6 650
610 975 1 390
330 490 675
14.4 13.2 12.4
22 000 13 000 26 000 17 000 12 000 20 000 15 000 11 000 18 000
6003 6203 6303
ZZ ZZ ZZ
VV DDU VV DDU VV DDU
N N N
NR NR NR
2.06 2.06 2.46
1.35 1.35 1.35
33.17 38.10 44.60
0.40 0.40 0.40
0.3 0.5 0.5
39.7 44.6 52.7
1.12 1.12 1.12
19 21 22
21.5 23.5 25.5
33 36 42
0.3 0.6 1
40.5 45.5 53.5
2.9 2.9 3.3
0.041 0.067 0.113
32 37 42
7 9 8
0.3 0.3 0.3
4 000 6 400 7 900
2 470 3 700 4 450
410 650 810
252 375 455
15.5 14.7 14.5
22 000 13 000 26 000 19 000 12 000 22 000 18 000 — 20 000
6804 6904 16004
ZZ ZZ —
VV DD VV DDU — —
N N —
NR NR —
1.30 1.70 —
0.95 0.95 —
30.70 35.70 —
0.25 0.25 —
0.3 0.3 —
34.8 39.8 —
0.85 0.85 —
22 22 22
22 24 —
30 35 40
0.3 0.3 0.3
35.5 40.5 —
1.8 2.3 —
0.017 0.037 0.048
42 47 52
12 14 15
0.6 1 1.1
9 400 12 800 15 900
5 000 6 600 7 900
955 1 300 1 620
510 670 805
13.8 13.1 12.4
18 000 11 000 20 000 15 000 11 000 18 000 14 000 10 000 17 000
6004 6204 6304
ZZ ZZ ZZ
VV DDU VV DDU VV DDU
N N N
NR NR NR
2.06 2.46 2.46
1.35 1.35 1.35
39.75 44.60 49.73
0.40 0.40 0.40
0.5 0.5 0.5
46.3 52.7 57.9
1.12 1.12 1.12
24 25 26.5
25.5 26.5 28
38 42 45.5
0.6 1 1
47 53.5 58.5
2.9 3.3 3.3
0.068 0.107 0.145
44 50 56
12 14 16
0.6 1 1.1
9 400 12 900 18 400
5 050 6 800 9 250
960 1 320 1 870
515 695 940
14.0 13.5 12.4
17 000 11 000 20 000 14 000 9 500 16 000 13 000 9 500 16 000
60/22 62/22 63/22
ZZ ZZ ZZ
VV DDU VV DDU VV DDU
N N N
NR NR NR
2.06 2.46 2.46
1.35 1.35 1.35
41.75 47.60 53.60
0.40 0.40 0.40
0.5 0.5 0.5
48.3 55.7 61.7
1.12 1.12 1.12
26 27 28.5
26.5 29.5 30.5
40 45 49.5
0.6 1 1
49 56.5 62.5
2.9 3.3 3.3
0.074 0.119 0.179
Notes (1) For tolerances for the snap ring grooves and snap ring dimensions, refer to Pages A50 to A53. (2) When heavy axial loads are applied, increase da and decrease Da from the above values. (3) Ring types N and NR applicable only to open-type bearings. Please consult NSK about the snap ring groove dimensions of sealed or shielded bearings. B8 (4) Snap ring groove dimensions and snap ring dimensions are not conformed to ISO15.
B001-029E.indd 8-9
NR NR
NR NR NR
Remarks 1. Diameter Series 7 (extra thin section bearings) are also available, please contact NSK. 2. When using bearings with rotating outer rings, contact NSK if they are sealed, shielded, or have snap rings.
B9
11/20/13 4:53:37 PM
SINGLE-ROW DEEP GROOVE BALL BEARINGS Bore Diameter
Dynamic Equivalent Load P =X Fr +Y Fa
25 – 45 mm f
B
f 0 Fa
rN a
r
b
C 0r
r0
ra
r
ra
jD
jD 2
jd
jDa
0.172 0.345 0.689 1.03 1.38 2.07 3.45 5.17 6.89
ra jda jD X
jD 1
Open Type
Shielded Type ZZ
Basic Load Ratings
Boundary Dimensions (mm)
d
D
Non-Contact Sealed Type VV
(N)
r
B
Cr
Contact Sealed Type DD · DDU Factor
{kgf}
C 0r
Cr
C 0r
f0
28 30
32 35
40
45
37 42 47 47 52 62 52 58 68 42 47 55 55 62 72 58 65 75 47 55 62 62 72 80 52 62 68 68 80 90 58 68 75 75 85 100
7 9 8 12 15 17 12 16 18 7 9 9 13 16 19 13 17 20 7 10 9 14 17 21 7 12 9 15 18 23 7 12 10 16 19 25
0.3 0.3 0.3 0.6 1 1.1 0.6 1 1.1 0.3 0.3 0.3 1 1 1.1 1 1 1.1 0.3 0.6 0.3 1 1.1 1.5 0.3 0.6 0.3 1 1.1 1.5 0.3 0.6 0.6 1 1.1 1.5
4 500 7 050 8 850 10 100 14 000 20 600 12 500 16 600 26 700 4 700 7 250 11 200 13 200 19 500 26 700 15 100 20 700 29 900 4 900 10 600 11 700 16 000 25 700 33 500 6 350 13 700 12 600 16 800 29 100 40 500 6 600 14 100 14 900 20 900 31 500 53 000
3 150 4 550 5 600 5 850 7 850 11 200 7 400 9 500 14 000 3 650 5 000 7 350 8 300 11 300 15 000 9 150 11 600 17 000 4 100 7 250 8 200 10 300 15 300 19 200 5 550 10 000 9 650 11 500 17 900 24 000 6 150 10 900 11 400 15 200 20 400 32 000
455 715 905 1 030 1 430 2 100 1 270 1 700 2 730 480 740 1 150 1 350 1 980 2 720 1 530 2 120 3 050 500 1 080 1 190 1 630 2 620 3 400 650 1 390 1 290 1 710 2 970 4 150 670 1 440 1 520 2 140 3 200 5 400
320 460 570 595 800 1 150 755 970 1 430 370 510 750 845 1 150 1 530 935 1 190 1 730 420 740 835 1 050 1 560 1 960 565 1 020 985 1 180 1 820 2 450 625 1 110 1 160 1 550 2 080 3 250
16.1 15.4 15.1 14.5 13.9 13.2 14.5 13.9 12.4 16.4 15.8 15.2 14.7 13.8 13.3 14.5 13.6 13.2 16.7 15.5 15.6 14.8 13.8 13.2 17.0 15.7 16.0 15.3 14.0 13.2 17.2 15.9 15.9 15.3 14.4 13.1
Open Z · ZZ V · VV
DU DDU
Bearing Numbers
Oil Open Z
18 000 10 000 22 000 16 000 10 000 19 000 15 000 — 18 000 15 000 9 500 18 000 13 000 9 000 15 000 11 000 8 000 13 000 14 000 8 500 16 000 12 000 8 000 14 000 10 000 7 500 13 000 15 000 9 000 18 000 14 000 8 500 17 000 13 000 — 15 000 13 000 8 000 15 000 11 000 7 500 13 000 9 500 6 700 12 000 12 000 7 500 14 000 10 000 7 100 12 000 9 000 6 300 11 000 14 000 7 500 16 000 12 000 7 500 15 000 11 000 — 13 000 11 000 6 700 13 000 9 500 6 300 11 000 8 500 6 000 10 000 12 000 6 700 14 000 11 000 6 300 13 000 10 000 — 12 000 10 000 6 000 12 000 8 500 5 600 10 000 7 500 5 300 9 000 11 000 6 000 13 000 9 500 5 600 12 000 9 000 — 11 000 9 000 5 300 11 000 7 500 5 300 9 000 6 700 4 800 8 000
Open Shielded
6805 6905 16005 6005 6205 6305 60/28 62/28 63/28 6806 6906 16006 6006 6206 6306 60/32 62/32 63/32 6807 6907 16007 6007 6207 6307 6808 6908 16008 6008 6208 6308 6809 6909 16009 6009 6209 6309
ZZ ZZ — ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ — ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ — ZZ ZZ ZZ ZZ ZZ — ZZ ZZ ZZ ZZ ZZ — ZZ ZZ ZZ
Sealed
VV VV — VV VV VV VV VV VV VV VV — VV VV VV VV VV VV VV VV — VV VV VV VV VV — VV VV VV VV VV — VV VV VV
Notes (1) For tolerances for the snap ring grooves and snap ring dimensions, refer to Pages A50 to A53. (2) When heavy axial loads are applied, increase da and decrease Da from the above values. (3) Ring types N and NR applicable only to open-type bearings. Please consult NSK about the snap ring groove dimensions of sealed or shielded bearings. B 10 (4) Not conformed to ISO15.
B001-029E.indd 10-11
DD DDU — DDU DDU DDU DDU DDU DDU DD DDU — DDU DDU DDU DDU DDU DDU DD DDU — DDU DDU DDU DD DDU — DDU DDU DDU DD DDU — DDU DDU DDU
Snap Ring Groove Dimensions (1) With With Snap Snap Ring Ring Groove N N( 3) — N N N N N N N N — N N N N N N N N — N N N N N — N N N N N — N N N
NR NR( 3) — NR NR NR NR NR NR NR NR — NR NR NR NR NR NR NR NR — NR NR NR NR NR — NR NR NR NR NR — NR NR NR
(mm)
Snap Ring (1) Dimensions
X 1 1 1 1 1 1 1 1 1
Y 0 0 0 0 0 0 0 0 0
X 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56
Y 2.30 1.99 1.71 1.55 1.45 1.31 1.15 1.04 1.00
(mm)
Mass
Abutment and Fillet Dimensions
(kg)
(mm)
a
b
D1
r0
rN
D2
f
max.
min.
max.
max.
min.
max.
max.
min.
max.
1.30 1.70 — 2.06 2.46 3.28 2.06 2.46 3.28 1.30 1.70 — 2.08 3.28 3.28 2.08 3.28 3.28 1.30 1.70 — 2.08 3.28 3.28 1.30 1.70 — 2.49 3.28 3.28 1.30 1.70 — 2.49 3.28 3.28
0.95 0.95 — 1.35 1.35 1.90 1.35 1.35 1.90 0.95 0.95 — 1.35 1.90 1.90 1.35 1.90 1.90 0.95 0.95 — 1.90 1.90 1.90 0.95 0.95 — 1.90 1.90 2.70 0.95 0.95 — 1.90 1.90 2.70
35.70 40.70 — 44.60 49.73 59.61 49.73 55.60 64.82 40.70 45.70 — 52.60 59.61 68.81 55.60 62.60 71.83 45.70 53.70 — 59.61 68.81 76.81 50.70 60.70 — 64.82 76.81 86.79 56.70 66.70 — 71.83 81.81 96.80
39.8 44.8 — 52.7 57.9 67.7 57.9 63.7 74.6 44.8 49.8 — 60.7 67.7 78.6 63.7 70.7 81.6 49.8 57.8 — 67.7 78.6 86.6 54.8 64.8 — 74.6 86.6 96.5 60.8 70.8 — 81.6 91.6 106.50
0.85 0.85 — 1.12 1.12 1.70 1.12 1.12 1.70 0.85 0.85 — 1.12 1.70 1.70 1.12 1.70 1.70 0.85 0.85 — 1.70 1.70 1.70 0.85 0.85 — 1.70 1.70 2.46 0.85 0.85 — 1.70 1.70 2.46
27 27 27 29 30 31.5 32 33 34.5 32 32 32 35 35 36.5 37 37 38.5 37 39 37 40 41.5 43 42 44 42 45 46.5 48 47 49 49 50 51.5 53
27 28.5 — 30 32 36 34 35.5 38 32 34 — 36.5 38.5 42.5 38.5 40 44.5 37 39 — 41.5 44.5 47 42 46 — 47.5 50.5 53 47.5 50 — 53.5 55.5 61.5
0.25 0.3 0.25 0.3 — — 0.40 0.5 0.40 0.5 0.60 0.5 0.40 0.5 0.40 0.5 0.60 0.5 0.25 0.3 0.25 0.3 — — 0.40 0.5 0.60 0.5 0.60 0.5 0.40 0.5 0.60 0.5 0.60 0.5 0.25 0.3 0.25 0.5 — — 0.60 0.5 0.60 0.5 0.60 0.5 0.25 0.3 0.25 0.5 — — 0.60 0.5 0.60 0.5 0.60 0.5 0.25 0.3 0.25 0.3( 4) — — 0.60 0.5 0.60 0.5 0.60 0.5
0.19 0.22 0.26 0.28 0.30 0.34 0.38 0.42 0.44
Fa >e Fr
Static Equivalent Load Fa >0.8, P0 =0.6Fr +0.5Fa Fr Fa ≤0.8, P0 =Fr Fr
CY
With Snap Ring NR
Limiting Speeds (min –1) Grease
min.
25
With Snap Ring Groove N
Fa ≤e Fr
e
d a(2)
D a(2)
ra
Dx
CY
max.
max.
min.
max.
0.3 0.3 0.3 0.6 1 1 0.6 1 1 0.3 0.3 0.3 1 1 1 1 1 1 0.3 0.6 0.3 1 1 1.5 0.3 0.6 0.3 1 1 1.5 0.3 0.6 0.6 1 1 1.5
40.5 45.5 — 53.5 58.5 68.5 58.5 64.5 76 45.5 50.5 — 61.5 68.5 80 64.5 71.5 83 50.5 58.5 — 68.5 80 88 55.5 65.5 — 76 88 98 61.5 72 — 83 93 108
35 40 45 43 47 55.5 48 53 61.5 40 45 53 50 57 65.5 53 60 68.5 45 51 60 57 65.5 72 50 58 66 63 73.5 82 56 64 71 70 78.5 92
approx.
1.8 2.3 — 2.9 3.3 4.6 2.9 3.3 4.6 1.8 2.3 — 2.9 4.6 4.6 2.9 4.6 4.6 1.8 2.3 — 3.4 4.6 4.6 1.8 2.3 — 3.8 4.6 5.4 1.8 2.3 — 3.8 4.6 5.4
0.021 0.042 0.059 0.079 0.129 0.235 0.096 0.175 0.287 0.024 0.052 0.087 0.116 0.199 0.345 0.122 0.225 0.389 0.027 0.075 0.107 0.151 0.284 0.464 0.031 0.112 0.13 0.19 0.366 0.636 0.038 0.126 0.167 0.241 0.42 0.829
Remarks 1. Diameter Series 7 (extra thin section bearings) are also available, please contact NSK. 2. When using bearings with rotating outer rings, contact NSK if they are sealed, shielded, or have snap rings.
B 11
11/20/13 4:53:38 PM
SINGLE-ROW DEEP GROOVE BALL BEARINGS Bore Diameter
Dynamic Equivalent Load P =X Fr +Y Fa
50 – 75 mm f
B
f 0 Fa
rN a
r
b
C 0r
r0
ra
r
ra
jD
jD 2
jd
jDa
0.172 0.345 0.689 1.03 1.38 2.07 3.45 5.17 6.89
ra jda jD X
jD 1
Open Type
Shielded Type ZZ
Basic Load Ratings
Boundary Dimensions (mm)
d
D
Non-Contact Sealed Type VV
(N)
r
B
Cr
Contact Sealed Type DD · DDU Factor
{kgf}
C 0r
Cr
C 0r
f0
65 72 80 80 90 110 72 80 90 90 100 120 78 85 95 95 110 130 85 90 100 100 120 140 90 100 110 110 125 150 95 105 115 115 130 160
55
60
65
70
75
7 12 10 16 20 27 9 13 11 18 21 29 10 13 11 18 22 31 10 13 11 18 23 33 10 16 13 20 24 35 10 16 13 20 25 37
0.3 0.6 0.6 1 1.1 2 0.3 1 0.6 1.1 1.5 2 0.3 1 0.6 1.1 1.5 2.1 0.6 1 0.6 1.1 1.5 2.1 0.6 1 0.6 1.1 1.5 2.1 0.6 1 0.6 1.1 1.5 2.1
6 400 14 500 15 400 21 800 35 000 62 000 8 800 16 000 19 400 28 300 43 500 71 500 11 500 19 400 20 000 29 500 52 500 82 000 11 900 17 400 20 500 30 500 57 500 92 500 12 100 23 700 26 800 38 000 62 000 104 000 12 500 24 400 27 600 39 500 66 000 113 000
6 200 11 700 12 400 16 600 23 200 38 500 8 500 13 300 16 300 21 200 29 300 44 500 10 900 16 300 17 500 23 200 36 000 52 000 12 100 16 100 18 700 25 200 40 000 60 000 12 700 21 200 23 600 31 000 44 000 68 000 13 900 22 600 25 300 33 500 49 500 77 000
655 1 480 1 570 2 220 3 600 6 300 900 1 630 1 980 2 880 4 450 7 300 1 170 1 980 2 040 3 000 5 350 8 350 1 220 1 770 2 090 3 100 5 850 9 450 1 230 2 420 2 730 3 900 6 350 10 600 1 280 2 480 2 820 4 050 6 750 11 600
635 1 200 1 260 1 700 2 370 3 900 865 1 350 1 660 2 170 2 980 4 550 1 120 1 660 1 780 2 370 3 700 5 300 1 230 1 640 1 910 2 570 4 100 6 100 1 300 2 160 2 410 3 150 4 500 6 950 1 410 2 300 2 580 3 400 5 050 7 850
17.2 16.1 16.1 15.6 14.4 13.2 17.0 16.2 16.2 15.3 14.3 13.1 16.9 16.2 16.3 15.6 14.3 13.1 17.0 16.6 16.5 15.8 14.4 13.2 17.2 16.3 16.3 15.6 14.5 13.2 17.3 16.5 16.4 15.8 14.7 13.2
Bearing Numbers
Oil
Open Z · ZZ V · VV
DU DDU
Open Z
9 500 9 000 8 500 8 500 7 100 6 000 8 500 8 000 7 500 7 500 6 300 5 600 8 000 7 500 7 100 7 100 5 600 5 300 7 500 7 100 6 700 6 700 5 300 4 800 6 700 6 300 6 000 6 000 5 000 4 500 6 300 6 000 5 600 5 600 4 800 4 300
5 300 5 300 — 4 800 4 800 4 300 4 800 4 500 — 4 500 4 300 4 000 4 500 4 300 — 4 000 3 800 3 600 4 000 4 000 — 4 000 3 600 3 400 3 800 3 600 — 3 600 3 400 3 200 3 600 3 400 — 3 400 3 200 2 800
11 000 11 000 10 000 10 000 8 500 7 500 10 000 9 500 9 000 9 000 7 500 6 700 9 500 9 000 8 500 8 500 7 100 6 300 8 500 8 500 8 000 8 000 6 300 6 000 8 000 7 500 7 100 7 100 6 300 5 300 7 500 7 100 6 700 6 700 5 600 5 000
Open Shielded
6810 6910 16010 6010 6210 6310 6811 6911 16011 6011 6211 6311 6812 6912 16012 6012 6212 6312 6813 6913 16013 6013 6213 6313 6814 6914 16014 6014 6214 6314 6815 6915 16015 6015 6215 6315
Notes (1) For tolerances for the snap ring grooves and snap ring dimensions, refer to Pages A50 to A53. (2) When heavy axial loads are applied, increase da and decrease Da from the above values.
B 12
B001-029E.indd 12-13
ZZ ZZ — ZZ ZZ ZZ ZZ ZZ — ZZ ZZ ZZ ZZ ZZ — ZZ ZZ ZZ ZZ ZZ — ZZ ZZ ZZ ZZ ZZ — ZZ ZZ ZZ ZZ ZZ — ZZ ZZ ZZ
Sealed
VV VV — VV VV VV VV VV — VV VV VV VV VV — VV VV VV VV VV — VV VV VV VV VV — VV VV VV VV VV — VV VV VV
DDU DDU — DDU DDU DDU DDU DDU — DDU DDU DDU DD DDU — DDU DDU DDU DD DDU — DDU DDU DDU DD DDU — DDU DDU DDU DDU DDU — DDU DDU DDU
Snap Ring Groove Dimensions (1) With With Snap Snap Ring Ring Groove N N — N N N N N — N N N N N — N N N N N — N N N N N — N N N N N — N N N
NR NR — NR NR NR NR NR — NR NR NR NR NR — NR NR NR NR NR — NR NR NR NR NR — NR NR NR NR NR — NR NR NR
(mm)
Snap Ring (1) Dimensions
Y 0 0 0 0 0 0 0 0 0
X 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56
Y 2.30 1.99 1.71 1.55 1.45 1.31 1.15 1.04 1.00
(mm)
Mass (kg)
(mm)
b
D1
r0
rN
D2
f
max.
min.
max.
max.
min.
max.
max.
min.
1.30 1.70 — 2.49 3.28 3.28 1.70 2.10 — 2.87 3.28 4.06 1.70 2.10 — 2.87 3.28 4.06 1.70 2.10 — 2.87 4.06 4.90 1.70 2.50 — 2.87 4.06 4.90 1.70 2.50 — 2.87 4.06 4.90
0.95 0.95 — 1.90 2.70 2.70 0.95 1.30 — 2.70 2.70 3.10 1.30 1.30 — 2.70 2.70 3.10 1.30 1.30 — 2.70 3.10 3.10 1.30 1.30 — 2.70 3.10 3.10 1.30 1.30 — 2.70 3.10 3.10
63.7 70.7 — 076.81 086.79 106.81 70.7 77.9 — 086.79 96.8 115.21 76.2 82.9 — 091.82 106.81 125.22 82.9 87.9 — 96.8 115.21 135.23 87.9 97.9 — 106.81 120.22 145.24 92.9 102.60 — 111.81 125.22 155.22
067.8 074.8 — 086.6 096.5 116.6 074.8 084.4 — 096.5 106.5 129.7 082.7 089.4 — 101.6 116.6 139.7 089.4 094.4 — 106.5 129.7 149.7 094.4 104.4 — 116.6 134.7 159.7 099.4 110.7 — 121.6 139.7 169.7
0.85 0.85 — 1.70 2.46 2.46 0.85 1.12 — 2.46 2.46 2.82 1.12 1.12 — 2.46 2.46 2.82 1.12 1.12 — 2.46 2.82 2.82 1.12 1.12 — 2.46 2.82 2.82 1.12 1.12 — 2.46 2.82 2.82
52 54 54 55 56.5 59 57 60 59 61.5 63 64 62 65 64 66.5 68 71 69 70 69 71.5 73 76 74 75 74 76.5 78 81 79 80 79 81.5 83 86
0.3 0.5 — 0.5 0.5 0.5 0.3 0.5 — 0.5 0.5 0.5 0.3 0.5 — 0.5 0.5 0.5 0.5 0.5 — 0.5 0.5 0.5 0.5 0.5 — 0.5 0.5 0.5 0.5 0.5 — 0.5 0.5 0.5
X 1 1 1 1 1 1 1 1 1
Abutment and Fillet Dimensions
a
0.25 0.25 — 0.60 0.60 0.60 0.25 0.40 — 0.60 0.60 0.60 0.40 0.40 — 0.60 0.60 0.60 0.40 0.40 — 0.60 0.60 0.60 0.40 0.40 — 0.60 0.60 0.60 0.40 0.40 — 0.60 0.60 0.60
0.19 0.22 0.26 0.28 0.30 0.34 0.38 0.42 0.44
Fa >e Fr
Static Equivalent Load Fa >0.8, P0 =0.6Fr +0.5Fa Fr Fa ≤0.8, P0 =Fr Fr
CY
With Snap Ring NR
Limiting Speeds (min –1) Grease
min.
50
With Snap Ring Groove N
Fa ≤e Fr
e
d a(2)
D a(2)
ra
Dx
CY
max.
max.
max.
min.
max.
52.5 55 — 58.5 60 68 59 61.5 — 64 66.5 72.5 64 66 — 69 74.5 79 69 71.5 — 73 80 85.5 74.5 77.5 — 80.5 84 92 79.5 82 — 85.5 90 98.5
63 68 76 75 83.5 101 70 75 86 83.5 92 111 76 80 91 88.5 102 119 81 85 96 93.5 112 129 86 95 106 103.5 117 139 91 100 111 108.5 122 149
0.3 0.6 0.6 1 1 2 0.3 1 0.6 1 1.5 2 0.3 1 0.6 1 1.5 2 0.6 1 0.6 1 1.5 2 0.6 1 0.6 1 1.5 2 0.6 1 0.6 1 1.5 2
68.5 76 — 88 98 118 76 86 — 98 108 131.5 84 91 — 103 118 141.5 91 96 — 108 131.5 152 96 106 — 118 136.5 162 101 112 — 123 141.5 172
1.8 2.3 — 3.8 5.4 5.4 2.3 2.9 — 5.0 5.4 6.5 2.5 2.9 — 5.0 5.4 6.5 2.5 2.9 — 5.0 6.5 7.3 2.5 3.3 — 5.0 6.5 7.3 2.5 3.3 — 5.0 6.5 7.3
approx.
0.050 0.135 0.175 0.261 0.459 1.06 0.081 0.189 0.257 0.381 0.619 1.37 0.103 0.192 0.281 0.412 0.783 1.72 0.128 0.218 0.30 0.439 1.0 2.11 0.134 0.349 0.441 0.608 1.09 2.57 0.149 0.364 0.463 0.649 1.19 3.08
Remarks 1. Diameter Series 7 (extra thin section bearings) are also available, please contact NSK. 2. When using bearings with rotating outer rings, contact NSK if they are sealed, shielded, or have snap rings. 3. Please consult NSK about the snap ring groove dimensions of sealed and shielded bearings when the diameter of dimension series 18 and 19 is 50 mm or more.
B 13
11/20/13 4:53:40 PM
SINGLE-ROW DEEP GROOVE BALL BEARINGS Bore Diameter
Dynamic Equivalent Load P =X Fr +Y Fa
80 – 105 mm f
B
f 0 Fa
rN a
r
b
C 0r
r0
ra
r
ra
jD
jD 2
jd
jDa
0.172 0.345 0.689 1.03 1.38 2.07 3.45 5.17 6.89
ra jda jD X
jD 1
Open Type
Shielded Type ZZ
Basic Load Ratings
Boundary Dimensions (mm)
d
D
Non-Contact Sealed Type VV
(N)
r
B
Cr
Contact Sealed Type DD · DDU Factor
{kgf}
C 0r
Cr
C 0r
f0
100 110 125 125 140 170 110 120 130 130 150 180 115 125 140 140 160 190 120 130 145 145 170 200 125 140 150 150 180 215 130 145 160 160 190 225
85
90
95
100
105
10 16 14 22 26 39 13 18 14 22 28 41 13 18 16 24 30 43 13 18 16 24 32 45 13 20 16 24 34 47 13 20 18 26 36 49
0.6 1 0.6 1.1 2 2.1 1 1.1 0.6 1.1 2 3 1 1.1 1 1.5 2 3 1 1.1 1 1.5 2.1 3 1 1.1 1 1.5 2.1 3 1 1.1 1 2 2.1 3
12 700 25 000 32 000 47 500 72 500 123 000 18 700 32 000 33 000 49 500 84 000 133 000 19 000 33 000 41 500 58 000 96 000 143 000 19 300 33 500 43 000 60 500 109 000 153 000 19 600 43 000 42 500 60 000 122 000 173 000 19 800 42 500 52 000 72 500 133 000 184 000
14 500 24 000 29 600 40 000 53 000 86 500 20 000 29 600 31 500 43 000 62 000 97 000 21 000 31 500 39 500 50 000 71 500 107 000 22 000 33 500 42 000 54 000 82 000 119 000 23 000 42 000 42 000 54 000 93 000 141 000 23 900 42 000 50 500 66 000 105 000 154 000
1 290 2 540 3 250 4 850 7 400 12 500 1 910 3 250 3 350 5 050 8 550 13 500 1 940 3 350 4 250 5 950 9 800 14 500 1 970 3 450 4 350 6 150 11 100 15 600 2 000 4 350 4 300 6 150 12 500 17 700 2 020 4 300 5 300 7 400 13 600 18 700
1 470 2 450 3 000 4 050 5 400 8 850 2 040 3 000 3 200 4 400 6 300 9 850 2 140 3 200 4 000 5 050 7 300 11 000 2 240 3 400 4 250 5 500 8 350 12 100 2 340 4 250 4 300 5 550 9 500 14 400 2 440 4 300 5 150 6 700 10 700 15 700
17.4 16.6 16.4 15.6 14.6 13.3 17.1 16.4 16.5 15.8 14.5 13.3 17.2 16.5 16.3 15.6 14.5 13.3 17.2 16.6 16.4 15.8 14.4 13.3 17.3 16.4 16.5 15.9 14.4 13.2 17.4 16.5 16.3 15.8 14.4 13.2
Bearing Numbers
Oil
Open Z · ZZ V · VV
DU DDU
Open Z
6 000 5 600 5 300 5 300 4 500 4 000 5 600 5 300 5 000 5 000 4 300 3 800 5 300 5 000 4 800 4 800 4 000 3 600 5 000 4 800 4 500 4 500 3 800 3 000 4 800 4 500 4 300 4 300 3 600 2 800 4 800 4 300 4 000 4 000 3 400 2 600
3 400 3 200 — 3 200 3 000 2 800 3 200 3 000 — 3 000 2 800 2 600 3 000 2 800 — 2 800 2 600 2 400 2 800 2 800 — 2 600 2 600 2 400 2 800 2 600 — 2 600 2 400 2 200 2 600 — — 2 400 2 200 2 000
7 100 6 700 6 300 6 300 5 300 4 800 6 700 6 300 6 000 6 000 5 000 4 500 6 300 6 000 5 600 5 600 4 800 4 300 6 000 5 600 5 300 5 300 4 500 3 600 5 600 5 300 5 300 5 300 4 300 3 400 5 600 5 300 4 800 4 800 4 000 3 200
Open Shielded
6816 6916 16016 6016 6216 6316 6817 6917 16017 6017 6217 6317 6818 6918 16018 6018 6218 6318 6819 6919 16019 6019 6219 6319 6820 6920 16020 6020 6220 6320 6821 6921 16021 6021 6221 6321
Notes (1) For tolerances for the snap ring grooves and snap ring dimensions, refer to Pages A50 to A53. (2) When heavy axial loads are applied, increase da and decrease Da from the above values.
B 14
B001-029E.indd 14-15
ZZ ZZ — ZZ ZZ ZZ ZZ ZZ — ZZ ZZ ZZ ZZ ZZ — ZZ ZZ ZZ ZZ ZZ — ZZ ZZ ZZ ZZ ZZ — ZZ ZZ ZZ ZZ ZZ — ZZ ZZ ZZ
Sealed
VV VV — VV VV VV VV VV — VV VV VV VV VV — VV VV VV VV VV — VV VV VV VV VV — VV VV VV VV VV — VV VV —
DDU DDU — DDU DDU DDU DDU DDU — DDU DDU DDU DDU DDU — DDU DDU DDU DD DDU — DDU DDU DDU DD DDU — DDU DDU DDU DDU — — DDU DDU DDU
Snap Ring Groove Dimensions (1) With With Snap Snap Ring Ring Groove N N — N N N N N — N N N N N — N N N N N — N N N N N — N N — N N — N N —
NR NR — NR NR NR NR NR — NR NR NR NR NR — NR NR NR NR NR — NR NR NR NR NR — NR NR — NR NR — NR NR —
(mm)
Snap Ring (1) Dimensions
Y 0 0 0 0 0 0 0 0 0
X 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56
Y 2.30 1.99 1.71 1.55 1.45 1.31 1.15 1.04 1.00
(mm)
Mass (kg)
(mm)
b
D1
r0
rN
D2
f
max.
min.
max.
max.
min.
max.
max.
min.
1.70 2.50 — 2.87 4.90 5.69 2.10 3.30 — 2.87 4.90 5.69 2.10 3.30 — 3.71 4.90 5.69 2.10 3.30 — 3.71 5.69 5.69 2.10 3.30 — 3.71 5.69 — 2.10 3.30 — 3.71 5.69 —
1.3 1.3 — 3.1 3.1 3.5 1.3 1.3 — 3.1 3.1 3.5 1.3 1.3 — 3.1 3.1 3.5 1.3 1.3 — 3.1 3.5 3.5 1.3 1.9 — 3.1 3.5 — 1.3 1.9 — 3.1 3.5 —
97.9 107.60 — 120.22 135.23 163.65 107.60 117.60 — 125.22 145.24 173.66 112.60 122.60 — 135.23 155.22 183.64 117.60 127.60 — 140.23 163.65 193.65 122.60 137.60 — 145.24 173.66 — 127.60 142.60 — 155.22 183.64 —
104.4 115.7 — 134.7 149.7 182.9 115.7 125.7 — 139.7 159.7 192.9 120.7 130.7 — 149.7 169.7 202.9 125.7 135.7 — 154.7 182.9 212.9 130.7 145.7 — 159.7 192.9 — 135.7 150.7 — 169.7 202.9 —
1.12 1.12 — 2.82 2.82 3.10 1.12 1.12 — 2.82 2.82 3.10 1.12 1.12 — 2.82 2.82 3.10 1.12 1.12 — 2.82 3.10 3.10 1.12 1.70 — 2.82 3.10 — 1.12 1.70 — 2.82 3.10 —
84 85 84 86.5 89 91 90 91.5 89 91.5 94 98 95 96.5 95 98 99 103 100 101.5 100 103 106 108 105 106.5 105 108 111 113 110 111.5 110 114 116 118
0.5 0.5 — 0.5 0.5 0.5 0.5 0.5 — 0.5 0.5 0.5 0.5 0.5 — 0.5 0.5 0.5 0.5 0.5 — 0.5 0.5 0.5 0.5 0.5 — 0.5 0.5 — 0.5 0.5 — 0.5 0.5 —
X 1 1 1 1 1 1 1 1 1
Abutment and Fillet Dimensions
a
0.4 0.4 — 0.6 0.6 0.6 0.4 0.4 — 0.6 0.6 0.6 0.4 0.4 — 0.6 0.6 0.6 0.4 0.4 — 0.6 0.6 0.6 0.4 0.6 — 0.6 0.6 — 0.4 0.6 — 0.6 0.6 —
0.19 0.22 0.26 0.28 0.30 0.34 0.38 0.42 0.44
Fa >e Fr
Static Equivalent Load Fa >0.8, P0 =0.6Fr +0.5Fa Fr Fa ≤0.8, P0 =Fr Fr
CY
With Snap Ring NR
Limiting Speeds (min –1) Grease
min.
80
With Snap Ring Groove N
Fa ≤e Fr
e
d a(2)
D a(2)
ra
Dx
CY
max.
max.
max.
min.
max.
84.5 87.5 — 91 95.5 104.5 90.5 94.5 — 96 102 110.5 95.5 98.5 — 103 107.5 117 101.5 103.5 — 108.5 114 123.5 105.5 111 — 112.5 121.5 133 110.5 116 — 120 127.5 138
96 105 121 118.5 131 159 105 113.5 126 123.5 141 167 110 118.5 135 132 151 177 115 123.5 140 137 159 187 120 133.5 145 142 169 202 125 138.5 155 151 179 212
0.6 1 0.6 1 2 2 1 1 0.6 1 2 2.5 1 1 1 1.5 2 2.5 1 1 1 1.5 2 2.5 1 1 1 1.5 2 2.5 1 1 1 2 2 2.5
106 117 — 136.5 152 185 117 127 — 141.5 162 195 122 132 — 152 172 205 127 137 — 157 185 215 132 147 — 162 195 — 137 152 — 172 205 —
2.5 3.3 — 5.3 7.3 8.4 2.9 4.1 — 5.3 7.3 8.4 2.9 4.1 — 6.1 7.3 8.4 2.9 4.1 — 6.1 8.4 8.4 2.9 4.7 — 6.1 8.4 — 2.9 4.7 — 6.1 8.4 —
approx.
0.151 0.391 0.621 0.872 1.42 3.67 0.263 0.55 0.652 0.918 1.76 4.28 0.276 0.585 0.873 1.19 2.18 4.98 0.297 0.601 0.904 1.23 2.64 5.76 0.31 0.828 0.945 1.29 3.17 7.04 0.324 0.856 1.24 1.58 3.79 8.09
Remarks 1. Diameter Series 7 (extra thin section bearings) are also available, please contact NSK. 2. When using bearings with rotating outer rings, contact NSK if they are sealed, shielded, or have snap rings. 3. Please consult NSK about the snap ring groove dimensions of sealed and shielded bearings when the diameter of dimension series 18 and 19 is 50 mm or more.
B 15
11/20/13 4:53:41 PM
SINGLE-ROW DEEP GROOVE BALL BEARINGS Bore Diameter
Dynamic Equivalent Load P =X Fr +Y Fa
110 – 160 mm f
B
f 0 Fa
rN a
r
b
C 0r
r0
ra
r
ra
jD
jD 2
jd
jDa
0.172 0.345 0.689 1.03 1.38 2.07 3.45 5.17 6.89
ra jda jD X
jD 1
Open Type
Shielded Type ZZ · ZZS
Basic Load Ratings
Boundary Dimensions (mm)
d
D
Non-Contact Sealed Type VV
(N)
r
B
Cr
Contact Sealed Type DD · DDU Factor
{kgf}
C 0r
Cr
C 0r
f0
140 150 170 170 200 240 150 165 180 180 215 260 165 180 200 200 230 280 175 190 210 210 250 300 190 210 225 225 270 320 200 220 240 240 290 340
120
130
140
150
160
16 20 19 28 38 50 16 22 19 28 40 55 18 24 22 33 40 58 18 24 22 33 42 62 20 28 24 35 45 65 20 28 25 38 48 68
1 1.1 1 2 2.1 3 1 1.1 1 2 2.1 3 1.1 1.5 1.1 2 3 4 1.1 1.5 1.1 2 3 4 1.1 2 1.1 2.1 3 4 1.1 2 1.5 2.1 3 4
28 100 43 500 57 500 85 000 144 000 205 000 28 900 53 000 56 500 88 000 155 000 207 000 37 000 65 000 75 500 106 000 167 000 229 000 38 500 66 500 77 500 110 000 166 000 253 000 47 500 85 000 84 000 126 000 176 000 274 000 48 500 87 000 99 000 137 000 185 000 278 000
32 500 44 500 56 500 73 000 117 000 179 000 35 500 54 000 57 500 80 000 131 000 185 000 44 000 67 500 77 500 101 000 146 000 214 000 48 000 72 000 82 500 109 000 150 000 246 000 58 500 90 500 91 000 126 000 168 000 284 000 61 000 96 000 108 000 135 000 186 000 287 000
2 860 4 450 5 850 8 650 14 700 20 900 2 950 5 400 5 800 9 000 15 800 21 100 3 750 6 650 7 700 10 800 17 000 23 400 3 900 6 800 7 900 11 200 17 000 25 800 4 850 8 650 8 550 12 800 18 000 28 000 4 950 8 850 10 100 13 900 18 900 28 300
3 350 4 550 5 800 7 450 11 900 18 300 3 650 5 500 5 850 8 150 13 400 18 800 4 450 6 850 7 900 10 300 14 900 21 800 4 850 7 300 8 400 11 100 15 300 25 100 5 950 9 200 9 250 12 800 17 100 28 900 6 250 9 800 11 000 13 800 19 000 29 200
17.1 16.6 16.3 15.5 14.3 13.2 17.3 16.5 16.5 15.7 14.4 13.5 17.1 16.5 16.4 15.8 14.5 13.6 17.3 16.6 16.5 16.0 14.9 13.6 17.1 16.5 16.6 15.9 15.1 13.9 17.2 16.6 16.5 15.9 15.4 13.9
Bearing Numbers
Oil
Open Z · ZZ V · VV
DU DDU
Open Z
4 300 4 300 3 800 3 800 2 800 2 400 4 000 3 800 3 600 3 600 2 600 2 200 3 600 3 400 3 000 3 000 2 400 2 200 3 400 3 200 2 800 2 800 2 200 2 000 3 200 2 600 2 600 2 600 2 000 1 800 2 600 2 600 2 400 2 400 1 900 1 700
2 400 2 400 — 2 200 2 200 — 2 200 — — 2 200 2 000 1 800 2 000 — — 1 900 — — 1 900 — — 1 800 1 700 — 1 800 1 700 — 1 700 — — 1 700 1 600 — 1 600 — —
5 300 5 000 4 500 4 500 3 400 3 000 4 800 4 500 4 300 4 300 3 200 2 800 4 300 4 000 3 600 3 600 3 000 2 600 4 000 3 800 3 400 3 400 2 800 2 400 3 800 3 200 3 000 3 000 2 600 2 200 3 200 3 000 2 800 2 800 2 400 2 000
Open Shielded
6822 6922 16022 6022 6222 6322 6824 6924 16024 6024 6224 6324 6826 6926 16026 6026 6226 6326 6828 6928 16028 6028 6228 6328 6830 6930 16030 6030 6230 6330 6832 6932 16032 6032 6232 6332
Notes (1) For tolerances for the snap ring grooves and snap ring dimensions, refer to Pages A50 to A53. (2) When heavy axial loads are applied, increase da and decrease Da from the above values.
B 16
B001-029E.indd 16-17
ZZ ZZ — ZZ ZZ ZZ ZZ ZZ — ZZ ZZ ZZS ZZS ZZ — ZZ ZZ ZZS ZZ ZZS — ZZ ZZS ZZS ZZ ZZS — ZZ ZZS ZZS ZZS ZZS — ZZ ZZS ZZS
Sealed
VV VV — VV VV — VV — — VV VV — VV — — — — — VV VV — — — — VV — — VV — — VV — — — — —
DDU DDU — DDU DDU — DD — — DDU DDU DDU DD — — DDU — — DDU — — DDU DDU — DDU DDU — DDU — — DDU DDU — DDU — —
Snap Ring Groove Dimensions (1) With With Snap Snap Ring Ring Groove N N — N N — N N — N — — N N — N — — N N — — — — N — — — — — N — — — — —
NR NR — NR NR — NR NR — NR — — NR NR — NR — — NR NR — — — — NR — — — — — NR — — — — —
(mm)
Snap Ring (1) Dimensions (mm)
a
b
D1
r0
rN
D2
f
max.
min.
max.
max.
min.
max.
max.
2.50 3.30 — 3.71 5.69 — 2.50 3.70 — 3.71 — — 3.30 3.70 — 5.69 — — 3.30 3.70 — — — — 3.30 — — — — — 3.30 — — — — —
1.9 1.9 — 3.5 3.5 — 1.9 1.9 — 3.5 — — 1.9 1.9 — 3.5 — — 1.9 1.9 — — — — 1.9 — — — — — 1.9 — — — — —
137.60 147.60 — 163.65 193.65 — 147.60 161.80 — 173.66 — — 161.80 176.80 — 193.65 — — 171.80 186.80 — — — — 186.80 — — — — — 196.80 — — — — —
0.6 0.6 — 0.6 0.6 — 0.6 0.6 — 0.6 — — 0.6 0.6 — 0.6 — — 0.6 0.6 — — — — 0.6 — — — — — 0.6 — — — — —
0.5 0.5 — 0.5 0.5 — 0.5 0.5 — 0.5 — — 0.5 0.5 — 0.5 — — 0.5 0.5 — — — — 0.5 — — — — — 0.5 — — — — —
145.7 155.7 — 182.9 212.9 — 155.7 171.5 — 192.9 — — 171.5 186.5 — 212.9 — — 181.5 196.5 — — — — 196.5 — — — — — 206.5 — — — — —
0.19 0.22 0.26 0.28 0.30 0.34 0.38 0.42 0.44
X 1 1 1 1 1 1 1 1 1
Y 0 0 0 0 0 0 0 0 0
Fa >e Fr X 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56
Y 2.30 1.99 1.71 1.55 1.45 1.31 1.15 1.04 1.00
Static Equivalent Load Fa >0.8, P0 =0.6Fr +0.5Fa Fr Fa ≤0.8, P0 =Fr Fr
CY
With Snap Ring NR
Limiting Speeds (min –1) Grease
min.
110
With Snap Ring Groove N
Fa ≤e Fr
e
1.7 1.7 — 3.1 3.1 — 1.7 1.7 — 3.1 — — 1.7 1.7 — 3.1 — — 1.7 1.7 — — — — 1.7 — — — — — 1.7 — — — — —
Mass
Abutment and Fillet Dimensions
(kg)
(mm)
d a(2) min.
115 116.5 115 119 121 123 125 126.5 125 129 131 133 136.5 138 136.5 139 143 146 146.5 148 146.5 149 153 156 156.5 159 156.5 161 163 166 166.5 169 168 171 173 176
D a(2)
ra
Dx
CY
max.
max.
max.
min.
max.
117 121 — 124.5 134 147 127 132 — 134.5 146 161 138 144 — 148.5 157 175 148.5 153.5 — 158.5 171.5 187 160 166 — 170 186 203 170.5 176 — 181.5 202 215.5
135 143.5 165 161 189 227 145 158.5 175 171 204 247 158.5 172 193.5 191 217 264 168.5 182 203.5 201 237 284 183.5 201 218.5 214 257 304 193.5 211 232 229 277 324
1 1 1 2 2 2.5 1 1 1 2 2 2.5 1 1.5 1 2 2.5 3 1 1.5 1 2 2.5 3 1 2 1 2 2.5 3 1 2 1.5 2 2.5 3
147 157 — 185 215 — 157 173 — 195 — — 173 188 — 215 — — 183 198 — — — — 198 — — — — — 208 — — — — —
3.9 4.7 — 6.4 8.4 — 3.9 5.1 — 6.4 — — 4.7 5.1 — 8.4 — — 4.7 5.1 — — — — 4.7 — — — — — 4.7 — — — — —
approx.
0.497 0.893 1.51 1.94 4.45 9.51 0.537 1.21 1.6 2.08 5.29 12.5 0.758 1.57 2.4 3.26 5.96 15.2 0.832 1.67 2.84 3.48 7.68 18.5 1.15 3.01 3.62 4.24 10 22.7 1.23 2.71 4.2 5.15 12.8 26.2
Remarks 1. When using bearings with rotating outer rings, contact NSK if they are sealed, shielded, or have snap rings. 2. Please consult NSK about the snap ring groove dimensions of sealed and shielded bearings when the diameter of dimension series 18 and 19 is 50 mm or more.
B 17
11/20/13 4:53:43 PM
SINGLE-ROW DEEP GROOVE BALL BEARINGS Bore Diameter
Dynamic Equivalent Load P =X Fr +Y Fa
170 – 240 mm B r
jD
jDa
jd
Shielded Type ZZS
Open Type
Basic Load Ratings
(mm)
d
D
(N)
r
B
Cr
Factor {kgf}
C 0r
Cr
C 0r
f0
215 230 260 260 310 360 225 250 280 280 320 380 240 260 290 290 340 400 250 280 310 310 360 420 270 300 340 340 400 460 300 320 360 360 440 500
180
190
200
220
240
22 28 28 42 52 72 22 33 31 46 52 75 24 33 31 46 55 78 24 38 34 51 58 80 24 38 37 56 65 88 28 38 37 56 72 95
1.1 2 1.5 2.1 4 4 1.1 2 2 2.1 4 4 1.5 2 2 2.1 4 5 1.5 2.1 2 2.1 4 5 1.5 2.1 2.1 3 4 5 2 2.1 2.1 3 4 5
60 000 86 000 114 000 161 000 212 000 325 000 60 500 119 000 145 000 180 000 227 000 355 000 73 000 113 000 149 000 188 000 255 000 355 000 74 000 143 000 161 000 207 000 269 000 380 000 76 500 146 000 180 000 235 000 310 000 410 000 98 500 154 000 196 000 244 000 340 000 470 000
75 000 97 000 126 000 161 000 224 000 355 000 78 500 128 000 157 000 185 000 241 000 405 000 93 500 127 000 168 000 201 000 282 000 415 000 98 000 158 000 180 000 226 000 310 000 445 000 107 000 169 000 217 000 271 000 375 000 520 000 137 000 190 000 243 000 296 000 430 000 625 000
6 100 8 750 11 700 16 400 21 700 33 500 6 200 12 100 14 700 18 400 23 200 36 000 7 450 11 500 15 200 19 200 26 000 36 000 7 550 14 600 16 400 21 100 27 400 38 500 7 800 14 900 18 400 24 000 31 500 42 000 10 000 15 700 19 900 24 900 34 500 48 000
7 650 9 850 12 900 16 400 22 800 36 000 8 000 13 100 16 000 18 800 24 600 41 500 9 550 13 000 17 100 20 500 28 700 42 500 10 000 16 100 18 300 23 000 31 500 45 500 10 900 17 300 22 100 27 600 38 500 53 000 14 000 19 400 24 700 30 000 44 000 63 500
17.1 16.7 16.5 15.8 15.3 13.6 17.2 16.4 16.3 15.6 15.1 13.9 17.1 16.6 16.4 15.8 15.0 14.1 17.2 16.4 16.4 15.6 15.2 13.8 17.4 16.6 16.5 15.6 15.1 14.3 17.3 16.8 16.5 15.9 15.2 14.2
jda
Fa ≤e Fr
e 0.19 0.22 0.26 0.28 0.30 0.34 0.38 0.42 0.44
X 1 1 1 1 1 1 1 1 1
Y 0 0 0 0 0 0 0 0 0
Fa >e Fr X 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56
Y 2.30 1.99 1.71 1.55 1.45 1.31 1.15 1.04 1.00
Static Equivalent Load Fa >0.8, P0 =0.6Fr +0.5Fa Fr Fa ≤0.8, P0 =Fr Fr
Non-Contact Sealed Type VV Limiting Speeds (min –1) Grease
min.
170
C 0r 0.172 0.345 0.689 1.03 1.38 2.07 3.45 5.17 6.89
ra
r
Boundary Dimensions
f 0Fa
ra
Abutment and Fillet Dimensions (mm)
Bearing Numbers
Oil
Open Z · ZZ V · VV
DU DDU
Open Z
2 600 2 400 2 200 2 200 1 800 1 600 2 400 2 200 2 000 2 000 1 700 1 500 2 200 2 200 2 000 2 000 1 600 1 400 2 200 2 000 1 900 1 900 1 500 1 300 1 900 1 800 1 600 1 700 1 300 1 200 1 700 1 700 1 500 1 500 1 200 1 100
1 600 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
3 000 2 800 2 600 2 600 2 200 2 000 2 800 2 600 2 400 2 400 2 000 1 800 2 600 2 600 2 400 2 400 2 000 1 700 2 600 2 400 2 200 2 200 1 800 1 600 2 400 2 200 2 000 2 000 1 600 1 500 2 000 2 000 1 900 1 900 1 500 1 300
Open Shielded
6834 6934 16034 6034 6234 6334 6836 6936 16036 6036 6236 6336 6838 6938 16038 6038 6238 6338 6840 6940 16040 6040 6240 6340 6844 6944 16044 6044 6244 6344 6848 6948 16048 6048 6248 6348
ZZS ZZS — ZZS ZZS — — ZZS — ZZS ZZS — — — — ZZS ZZS — — ZZS — ZZS ZZS — ZZS ZZS — ZZS — — — ZZS — — — —
Sealed
VV — — VV — — VV — — VV — — VV — — — — — — — — — — — — — — — — — — — — — — —
DDU — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
d a(1)
Mass (kg)
D a(1)
ra
min.
max.
max.
max.
approx.
176.5 179 178 181 186 186 186.5 189 189 191 196 196 198 199 199 201 206 210 208 211 209 211 216 220 228 231 231 233 236 240 249 251 251 253 256 260
182.0 186.0 — 194.5 215.0 — 192.0 198.5 — 208.0 223.0 — 202.5 — — 218.0 236.0 — — 222.0 — 231.5 252.0 — 233.5 242.0 — 254.5 — — — 262.0 — — — —
208.5 221 252 249 294 344 218.5 241 271 269 304 364 232 251 281 279 324 380 242 269 301 299 344 400 262 289 329 327 384 440 291 309 349 347 424 480
1 2 1.5 2 3 3 1 2 2 2 3 3 1.5 2 2 2 3 4 1.5 2 2 2 3 4 1.5 2 2 2.5 3 4 2 2 2 2.5 3 4
1.86 3.34 5.71 6.89 15.8 36.6 1.98 4.16 7.5 8.88 15.9 43.1 2.53 5.18 7.78 9.39 22.3 49.7 2.67 7.28 10 12 26.7 55.3 2.9 7.88 13.1 18.6 37.4 73.9 4.48 8.49 13.9 19.9 50.5 94.4
Note (1) When heavy axial loads are applied, increase da and decrease Da from the above values. Remarks When using bearings with rotating outer rings, contact NSK if they are sealed or shielded.
B 18
B001-029E.indd 18-19
B 19
11/20/13 4:53:44 PM
SINGLE-ROW DEEP GROOVE BALL BEARINGS Bore Diameter
Dynamic Equivalent Load P =X Fr +Y Fa
260 – 360 mm
f 0Fa
B
C 0r
ra
r r
ra
jD
jd
jDa
jd a
Basic Load Ratings
(mm)
d
D
Factor
(N)
B
r
Cr
Limiting Speeds
{kgf}
C 0r
Cr
(min –1)
C 0r
f0
Grease
Oil
Bearing Numbers Open
min.
Abutment and Fillet Dimensions (mm)
Da(1)
ra
min.
max.
max.
approx.
4.84 14 21.1
148 000 255 000 310 000
10 300 20 800 24 100
15 100 26 000 31 500
17.4 16.5 16.4
1 600 1 500 1 400
1 900 1 800 1 700
6852 6952 16052
269 271 273
311 349 387
2 2 2.5
4 5 6
291 000 400 000 505 000
375 000 540 000 710 000
29 700 41 000 51 500
38 500 55 000 72 500
15.8 15.1 14.6
1 400 1 100 1 000
1 700 1 300 1 200
6052 6252 6352
276 280 286
384 460 514
3 4 5
2 2.1 3
133 000 209 000 243 000
191 000 272 000 330 000
13 600 21 300 24 700
19 500 27 700 33 500
17.3 16.6 16.5
1 500 1 400 1 300
1 700 1 700 1 600
6856 6956 16056
289 291 293
341 369 407
2 2 2.5
4 5 6
300 000 400 000 570 000
410 000 550 000 840 000
31 000 41 000 58 000
41 500 56 000 86 000
16.0 15.2 14.5
1 300 1 000 900
1 600 1 300 1 100
6056 6256 6356
296 300 306
404 480 554
3 4 5
38 56 50
2.1 3 4
166 000 269 000 285 000
233 000 370 000 405 000
17 000 27 400 29 000
23 800 38 000 41 000
17.1 16.4 16.4
1 300 1 300 1 200
1 600 1 500 1 400
6860 6960 16060
311 313 316
369 407 444
2 2.5 3
10.3 23.9 31.5
460 540
74 85
4 5
355 000 465 000
500 000 670 000
36 500 47 500
51 000 68 500
15.8 15.1
1 200 950
1 400 1 200
6060 6260
316 320
444 520
3 4
44.2 87.8
400 440 480
38 56 50
2.1 3 4
168 000 266 000 293 000
244 000 375 000 430 000
17 200 27 100 29 800
24 900 38 000 44 000
17.2 16.5 16.5
1 300 1 200 1 100
1 500 1 400 1 300
6864 6964 16064
331 333 336
389 427 464
2 2.5 3
10.8 25.3 33.2
480 580
74 92
4 5
390 000 530 000
570 000 805 000
40 000 54 500
58 000 82 500
15.7 15.0
1 100 850
1 300 1 100
6064 6264
336 340
464 560
3 4
46.5 111
340
420 460 520 620
38 56 82 92
2.1 3 5 6
175 000 273 000 440 000 530 000
265 000 400 000 660 000 820 000
17 800 27 800 45 000 54 000
27 100 40 500 67 500 83 500
17.3 16.6 15.6 15.3
1 200 1 100 1 000 800
1 400 1 300 1 200 1 000
6868 6968 6068 6268
351 353 360 366
409 447 500 594
2 2.5 4 5
11.5 26.6 62.3 129
360
440 480 540 650
38 56 82 95
2.1 3 5 6
192 000 280 000 460 000 555 000
290 000 425 000 720 000 905 000
19 600 28 500 47 000 57 000
29 600 43 000 73 500 92 000
17.3 16.7 15.7 15.4
1 100 1 100 950 750
1 300 1 300 1 200 950
6872 6972 6072 6272
371 373 380 386
429 467 520 624
2 2.5 4 5
11.8 27.9 65.3 145
280
300
320
Note
28 46 44
400 480 540
65 80 102
350 380 420
33 46 44
420 500 580
65 80 108
380 420 460
Y 0 0 0 0 0 0 0 0 0
X 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56
Y 2.30 1.99 1.71 1.55 1.45 1.31 1.15 1.04 1.00
(kg)
da(1)
101 000 204 000 237 000
320 360 400
X 1 1 1 1 1 1 1 1 1
Mass
2 2.1 3
260
0.19 0.22 0.26 0.28 0.30 0.34 0.38 0.42 0.44
Fa >e Fr
Static Equivalent Load Fa >0.8, P0 =0.6Fr +0.5Fa Fr Fa ≤0.8, P0 =Fr Fr
Open Type
Boundary Dimensions
0.172 0.345 0.689 1.03 1.38 2.07 3.45 5.17 6.89
Fa ≤e Fr
e
29.4 67 118 7.2 15.1 22.7 31.2 70.4 144
(1) When heavy axial loads are applied, increase da and decrease Da from the above values.
B 20
B001-029E.indd 20-21
B 21
11/20/13 4:53:45 PM
SINGLE-ROW DEEP GROOVE BALL BEARINGS Bore Diameter
Dynamic Equivalent Load P =X Fr +Y Fa
380 – 600 mm
f 0Fa
B
C 0r
ra
r r
ra
jD
jd
jDa
jd a
Basic Load Ratings
(mm)
d
D
(N)
B
r
Cr
Factor
Limiting Speeds
{kgf}
C 0r
Cr
(min –1)
C 0r
f0
Grease
Oil
Bearing Numbers Open
min.
Abutment and Fillet Dimensions (mm)
X 1 1 1 1 1 1 1 1 1
Y 0 0 0 0 0 0 0 0 0
X 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56
Y 2.30 1.99 1.71 1.55 1.45 1.31 1.15 1.04 1.00
Mass (kg)
da(1)
Da(1)
ra
min.
max.
max.
approx.
380
480 520 560
46 65 82
2.1 4 5
238 000 325 000 455 000
375 000 510 000 725 000
24 200 33 000 46 500
38 000 52 000 74 000
17.1 16.6 15.9
1 000 950 900
1 200 1 200 1 100
6876 6976 6076
391 396 400
469 504 540
2 3 4
19.5 40 68
400
500 540 600
46 65 90
2.1 4 5
241 000 335 000 510 000
390 000 540 000 825 000
24 600 34 000 52 000
40 000 55 000 84 000
17.2 16.7 15.7
950 900 850
1 200 1 100 1 000
6880 6980 6080
411 416 420
489 524 580
2 3 4
20.5 42 88.4
420
520 560 620
46 65 90
2.1 4 5
245 000 340 000 530 000
410 000 570 000 895 000
25 000 35 000 54 000
41 500 58 500 91 000
17.3 16.8 15.8
900 900 800
1 100 1 100 1 000
6884 6984 6084
431 436 440
509 544 600
2 3 4
21.4 43.6 92.2
440
540 600 650
46 74 94
2.1 4 6
248 000 395 000 550 000
425 000 680 000 965 000
25 300 40 500 56 000
43 500 69 000 98 500
17.4 16.6 16.0
900 800 750
1 100 1 000 900
6888 6988 6088
451 456 466
529 584 624
2 3 5
22.3 60.2 106
460
580 620 680
56 74 100
3 4 6
310 000 405 000 605 000
550 000 720 000 1 080 000
31 500 41 500 62 000
56 000 73 500 110 000
17.1 16.7 15.8
800 800 710
1 000 950 850
6892 6992 6092
473 476 486
567 604 654
2.5 3 5
34.3 62.6 123
480
600 650 700
56 78 100
3 5 6
315 000 450 000 605 000
575 000 815 000 1 090 000
32 000 45 500 61 500
58 500 83 000 111 000
17.2 16.6 15.9
800 750 710
950 900 850
6896 6996 6096
493 500 506
587 630 674
2.5 4 5
35.4 73.5 127
500
620 670 720
56 78 100
3 5 6
320 000 460 000 630 000
600 000 865 000 1 170 000
33 000 47 000 64 000
61 000 88 000 120 000
17.3 16.7 16.0
750 710 670
900 850 800
68/500 69/500 60/500
513 520 526
607 650 694
2.5 4 5
37.2 82 131
530
650 710 780
56 82 112
3 5 6
325 000 455 000 680 000
625 000 870 000 1 300 000
33 000 46 500 69 500
63 500 88 500 133 000
17.4 16.8 16.0
710 670 600
850 800 750
68/530 69/530 60/530
543 550 556
637 690 754
2.5 4 5
39.8 89.8 184
560
680 750 820
56 85 115
3 5 6
330 000 525 000 735 000
650 000 1 040 000 1 500 000
33 500 53 500 75 000
66 500 106 000 153 000
17.4 16.7 16.2
670 600 560
800 750 670
68/560 69/560 60/560
573 580 586
667 730 793.5
2.5 4 5
41.5 105 203
600
730 800 870
60 90 118
3 5 6
355 000 550 000 790 000
735 000 1 160 000 1 640 000
36 000 56 500 80 500
75 000 118 000 168 000
17.5 16.9 16.1
600 560 530
710 670 630
68/600 69/600 60/600
613 620 626
717 780 844
2.5 4 5
50.9 120 236
Note
0.19 0.22 0.26 0.28 0.30 0.34 0.38 0.42 0.44
Fa >e Fr
Static Equivalent Load Fa >0.8, P0 =0.6Fr +0.5Fa Fr Fa ≤0.8, P0 =Fr Fr
Open Type
Boundary Dimensions
0.172 0.345 0.689 1.03 1.38 2.07 3.45 5.17 6.89
Fa ≤e Fr
e
(1) When heavy axial loads are applied, increase da and decrease Da from the above values.
B 22
B001-029E.indd 22-23
B 23
11/20/13 4:53:46 PM
SINGLE-ROW DEEP GROOVE BALL BEARINGS Bore Diameter
Dynamic Equivalent Load P =X Fr +Y Fa
630 – 800 mm
f 0Fa
B
C 0r
ra
r r
ra
jD
jd
jDa
jd a
Basic Load Ratings
(mm)
d
D
(N)
B
r
Cr
Factor
Limiting Speeds
{kgf}
C 0r
Cr
(min –1)
C 0r
f0
Grease
Oil
Bearing Numbers Open
min.
Abutment and Fillet Dimensions (mm)
X 1 1 1 1 1 1 1 1 1
Y 0 0 0 0 0 0 0 0 0
X 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56
Y 2.30 1.99 1.71 1.55 1.45 1.31 1.15 1.04 1.00
Mass (kg)
da(1)
Da(1)
ra
min.
max.
max.
approx.
630
780 850 920
69 100 128
4 6 7.5
420 000 625 000 750 000
890 000 1 350 000 1 620 000
43 000 64 000 76 500
90 500 138 000 165 000
17.3 16.7 16.4
560 530 480
670 630 600
68/630 69/630 60/630
646 656 662
764 824 888
3 5 6
71.3 163 285
670
820 900 980
69 103 136
4 6 7.5
435 000 675 000 765 000
965 000 1 460 000 1 730 000
44 500 68 500 78 000
98 000 149 000 177 000
17.4 16.7 16.6
500 480 450
630 560 530
68/670 69/670 60/670
686 696 702
804 874 948
3 5 6
75.4 181 351
710
870 950
74 106
4 6
480 000 715 000
1 100 000 1 640 000
49 000 72 500
113 000 167 000
17.4 16.8
480 450
560 530
68/710 69/710
726 736
854 924
3 5
92.6 208
750
920 1 000
78 112
5 6
525 000 785 000
1 260 000 1 840 000
53 500 80 000
128 000 188 000
17.4 16.7
430 400
530 500
68/750 69/750
770 776
900 974
4 5
110 245
800
980 1 060
82 115
5 6
530 000 825 000
1 310 000 2 050 000
54 000 84 500
133 000 209 000
17.5 16.8
400 380
480 450
68/800 69/800
820 826
960 1 034
4 5
132 275
Note
0.19 0.22 0.26 0.28 0.30 0.34 0.38 0.42 0.44
Fa >e Fr
Static Equivalent Load Fa >0.8, P0 =0.6Fr +0.5Fa Fr Fa ≤0.8, P0 =Fr Fr
Open Type
Boundary Dimensions
0.172 0.345 0.689 1.03 1.38 2.07 3.45 5.17 6.89
Fa ≤e Fr
e
(1) When heavy axial loads are applied, increase da and decrease Da from the above values.
B 24
B001-029E.indd 24-25
B 25
11/20/13 4:53:47 PM
MAXIMUM TYPE BALL BEARINGS Bore Diameter
25 – 110 mm B r r
jD
jd
Shielded Type (One Shield) Z
Boundary Dimensions
Limiting Speeds
(N)
B
r
Cr
{kgf}
C 0r
Cr
C 0r
min.
25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110
52 62 62 72 72 80 80 90 85 100 90 110 100 120 110 130 120 140 125 150 130 160 140 170 150 180 160 190 170 200 180 190 200
15 17 16 19 17 21 18 23 19 25 20 27 21 29 22 31 23 33 24 35 25 37 26 39 28 41 30 43 32 45 34 36 38
1 1.1 1 1.1 1.1 1.5 1.1 1.5 1.1 1.5 1.1 2 1.5 2 1.5 2.1 1.5 2.1 1.5 2.1 1.5 2.1 2 2.1 2 3 2 3 2.1 3 2.1 2.1 2.1
ra
ra
14 400 21 500 21 000 27 900 27 800 37 000 35 500 46 500 37 000 55 500 39 000 65 000 48 000 75 000 58 000 85 500 63 500 103 000 69 000 115 000 72 000 126 000 84 000 136 000 93 000 147 000 107 000 158 000 121 000 169 000 136 000 148 000 160 000
10 500 15 500 16 300 20 700 22 100 29 100 28 800 36 000 32 000 44 000 35 000 52 500 44 000 61 500 54 000 71 500 60 000 89 500 66 000 102 000 72 000 116 000 85 000 130 000 93 000 145 000 107 000 161 000 123 000 178 000 140 000 157 000 176 000
jD a
jd a
jd b
Shielded Type (Two Shields) ZZ
Basic Load Ratings
(mm)
D
ra
jD a
Open Type
d
ra
1 470 2 200 2 150 2 840 2 830 3 800 3 600 4 750 3 800 5 650 3 950 6 600 4 900 7 650 5 950 8 700 6 450 10 500 7 050 11 800 7 350 12 800 8 600 13 900 9 500 15 000 10 900 16 100 12 300 17 300 13 800 15 000 16 300
1 070 1 580 1 660 2 110 2 250 2 970 2 940 3 650 3 250 4 500 3 550 5 350 4 500 6 250 5 550 7 300 6 150 9 150 6 750 10 400 7 300 11 800 8 650 13 300 9 450 14 800 10 900 16 400 12 500 18 100 14 200 16 000 17 900
(min –1) Grease Open Z · ZZ
12 000 11 000 10 000 9 000 9 000 8 000 8 000 7 500 7 500 6 300 6 700 6 000 6 300 5 600 5 600 5 000 5 300 4 800 5 000 4 300 4 500 4 000 4 300 3 800 4 000 3 600 3 800 3 400 3 600 2 800 3 400 3 200 2 800
Bearing Numbers
Mass
Abutment and Fillet Dimensions
(kg)
(mm) Oil Open Z
15 000 13 000 12 000 11 000 11 000 9 500 9 500 9 000 9 000 8 000 8 500 7 100 7 500 6 700 6 700 6 000 6 300 5 600 6 000 5 300 5 600 5 000 5 300 4 500 5 000 4 300 4 500 4 000 4 300 3 600 4 000 3 800 3 400
Open
BL 205 BL 305 BL 206 BL 306 BL 207 BL 307 BL 208 BL 308 BL 209 BL 309 BL 210 BL 310 BL 211 BL 311 BL 212 BL 312 BL 213 BL 313 BL 214 BL 314 BL 215 BL 315 BL 216 BL 316 BL 217 BL 317 BL 218 BL 318 BL 219 BL 319 BL 220 BL 221 BL 222
With One Shielded
With Two Shields
BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL
BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL BL
205 305 206 306 207 307 208 308 209 309 210 310 211 311 212 312 213 313 214 314 215 315 216 316 217 317 218 318 219 319 220 221 —
Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z
205 305 206 306 207 307 208 308 209 309 210 310 211 311 212 312 213 313 214 314 215 315 216 316 217 317 218 318 219 319 220 221 —
ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ
da
db
Da
ra
min.
max.
max.
max.
approx.
30 31.5 35 36.5 41.5 43 46.5 48 51.5 53 56.5 59 63 64 68 71 73 76 78 81 83 86 89 91 94 98 99 103 106 108 111 116 121
32 36 38.5 42 44.5 44.5 50 52.5 55.5 61.5 60 68 66.5 72.5 74.5 79 80 85.5 84 92 90 98.5 95.5 104.5 102 110.5 107.5 117 114 124 121.5 127.5 —
47 55.5 57 65.5 65.5 72 73.5 82 78.5 92 83.5 101 92 111 102 119 112 129 117 139 122 149 131 159 141 167 151 177 159 187 169 179 189
1 1 1 1 1 1.5 1 1.5 1 1.5 1 2 1.5 2 1.5 2 1.5 2 1.5 2 1.5 2 2 2 2 2.5 2 2.5 2 2.5 2 2 2
0.133 0.246 0.215 0.364 0.307 0.486 0.394 0.685 0.449 0.883 0.504 1.16 0.667 1.49 0.856 1.88 1.09 2.36 1.19 2.87 1.29 3.43 1.61 4.08 1.97 4.77 2.43 5.45 2.95 6.4 3.54 4.23 4.84
Remarks When using Maximum Type Ball Bearings, please contact NSK.
B 26
B001-029E.indd 26-27
B 27
11/20/13 4:53:47 PM
MAGNETO BEARINGS Bore Diameter
4 – 20 mm T C r
r1
Nominal Outside Diameter D (mm)
r B jD
jd
Over — 10 18 30
Boundary Dimensions
D
(N)
r
r1
min.
min.
B,C,T
Incl. 10 18 30 50
Cr
{kgf}
C 0r
Units : μm Single Plane Mean Outside Diameter & D mp E Series High + 8 + 8 + 9 +11
Cr
ra Dynamic Equivalent Load
jDa
EN Series
Low 0 0 0 0
High 0 0 0 0
Limiting Speeds
Basic Load Ratings
(mm)
d
ra
Outside Diameter Tolerance (Class N)
Grease
Oil
P =X Fr +Y Fa
Low – 8 – 8 – 9 –11
Bearing Numbers
Abutment and Fillet Dimensions (mm)
(min –1)
C 0r
jda
E Series
EN Series
Y
X
Y
1
0
0.5
2.5
e 0.2
(kg)
Da
ra
min.
max.
max.
approx.
14.8 14.8 19
0.15 0.15 0.3
0.005 0.004 0.011
4 5 6
16 16 21
5 5 7
0.15 0.15 0.3
0.1 0.1 0.15
1 650 1 650 2 490
288 288 445
168 168 254
29 29 46
34 000 34 000 30 000
40 000 40 000 36 000
E 4 E 5 E 6
EN 4 EN 5 EN 6
7 8 9
22 24 28
7 7 8
0.3 0.3 0.3
0.15 0.15 0.15
2 490 3 450 4 550
445 650 880
254 350 465
46 66 90
30 000 28 000 24 000
36 000 34 000 30 000
E 7 E 8 E 9
EN 7 EN 8 EN 9
9 10 11
20 22 26
0.3 0.3 0.3
0.013 0.014 0.022
10 11 12
28 32 32
8 7 7
0.3 0.3 0.3
0.15 0.15 0.15
4 550 4 400 4 400
880 845 845
465 450 450
90 86 86
24 000 22 000 22 000
30 000 26 000 26 000
E 10 E 11 E 12
EN 10 EN 11 EN 12
12 13 14
26 30 30
0.3 0.3 0.3
0.021 0.029 0.028
13 14
30 35
7 8
0.3 0.3
0.15 0.15
4 400 5 800
845 1 150
450 590
86 117
22 000 19 000
26 000 22 000
E 13 —
EN 13 EN 14
15 16
28 33
0.3 0.3
0.021 0.035
15
35 40 38
8 10 10
0.3 0.6 0.6
0.15 0.3 0.2
5 800 7 400 6 900
1 150 1 500 1 380
590 750 705
117 153 141
19 000 17 000 17 000
22 000 20 000 22 000
E 15 BO 15 —
EN 15 — EN 16
17 19 20
33 36 34
0.3 0.6 0.6
0.034 0.055 0.049
17
40 44 44
10 11 11
0.6 0.6 0.6
0.3 0.3 0.3
7 400 7 350 7 350
1 500 1 500 1 500
750 750 750
153 153 153
17 000 16 000 16 000
20 000 19 000 19 000
L 17 — BO 17
— EN 17 —
21 21 21
36 40 40
0.6 0.6 0.6
0.051 0.080 0.080
18 19
40 40
9 9
0.6 0.6
0.2 0.2
5 050 5 050
1 030 1 030
515 515
105 105
17 000 17 000
20 000 20 000
— E 19
EN 18 EN 19
22 23
36 36
0.6 0.6
0.051 0.049
20
47 47
12 14
1 1
0.6 0.6
11 000 11 000
2 380 2 380
1 120 1 120
243 243
14 000 14 000
17 000 17 000
E 20 L 20
EN 20 —
25 25
42 42
1 1
0.089 0.101
16
Fa/ Fr>e
X
Mass
da 5.2 6.2 8
Fa/ Fr≤e
Remarks 1. The outside diameters of Magneto Bearings Series E always have plus tolerances. 2. When using Magneto Bearings other than E, please contact NSK.
B 28
B001-029E.indd 28-29
B 29
11/20/13 4:53:48 PM
EXTRA SMALL BALL BEARINGS AND MINIATURE BALL BEARINGS EXTRA SMALL BALL BEARINGS · MINIATURE BALL BEARINGS Metric Design
Bore Diameter 1 – 9mm····················································· B34
With Flange Inch Design
Bore Diameter 1 – 9mm····················································· B38 Bore Diameter 1.016 – 9.525mm ······································· B42
With Flange
Bore Diameter 1.191 – 9.525mm ······································· B44
DESIGN AND TYPES The size ranges of extra small and miniature ball bearings are shown in Table 1. The design, types, and type symbols are shown in Table 2. Those types among them that are listed in the bearing tables are indicated by the in Table 2. shading Table 1 Size Ranges of Bearings Design Metric
Extra Small Ball Bearings Outside diameter D ≥ 9 Bore diameter
Inch
Miniature Ball Bearings Outside diameter D < 9
d < 10
Outside diameter D ≥ 9.525 Bore diameter
Units : mm
Outside diameter D < 9.525
d < 10
Please refer to NSK Miniature Ball Bearings (CAT. No. E126) for details.
ZZ
B 30
B030-045E.indd 30-31
ZZS
DD
VV
B 31
11/20/13 4:54:14 PM
Table 2 Design, Types, and Type Symbols
TOLERANCES AND RUNNING ACCURACY METRIC DESIGN BEARINGS ·································Table 8.2(Pages A60 to A63)
Type Symbols Special
Design · Types Metric
Inch Metric
Table 3 Flange Tolerances for Metric Flanged Bearings
Inch Shielded · sealed
嘷 嘷
6
The flange tolerances for metric design bearings are listed in Table 3.
Remarks
R
MR
—
bearings are available.
Nominal Flange
Deviation of Flange Outside Diameter
Outside Diameter
& D 1S
D1(mm) over
—
—
SMT
—
Thin section
Units : μm
(1) Tolerances of Flange Outside Diameter
1
2
incl.
high
low
high
low
10
+220
—36
0
—36
10
18
+270
—43
0
—43
18
30
+330
—52
0
—52
Single-Row Deep Groove Ball Bearings
Remarks 2is applied when the flange outside diameter is used for positioning. Shielded · sealed F6
嘷 嘷
FR
MF
—
available.
With flange
—
—
—
RW
Extended inner ring
—
Shielded bearings
over
incl.
are available.
2.5(1)
6
6
18
18
30
Deviation of Flange Width
Variation of Flange Width& C 1 S VC 1 S
& C 1S
Flange Backface Runout with Raceway S ea1
Normal and Classes 6,5,4,2 Normal and class 6 Class 5 Class 4 Class 2 Class 5 Class 4 Class 2 Class 5 Class 4 Class 2 high
low
Use the &BS tolerance for d of the same bearing of the same class
max. Use the & V BS tolerance for d of the same bearing of the same class
max.
max.
5
2.5
1.5
8
4
1.5
11
7
5
2.5
1.5
8
4
1.5
11
7
3 3
5
2.5
1.5
8
4
1.5
11
7
3
—
—
FRW
Shielded bearings are available.
INCH DESIGN BEARINGS ····································Table 8.2 (Pages A60 to A63)
—
—
—
SR00X00
Shielded bearings
Pivot Ball Bearings Thrust Ball Bearings
The flange tolerances for inch design flanged bearings are listed in Table 8.8(2) (Pages A76 and A77).
are available.
For synchro motors
INSTRUMENT BALL BEARINGS ··························Table 8.8 (Pages A76 to A77)
RECOMMENDED FITS —
—
BCF
—
Please refer to NSK Miniature Ball Bearings (CAT.No.E126).
INTERNAL CLEARANCES ·································Table 9.10 (Page A89) —
—
F
—
Remarks Single-row angular contact ball bearings are available besides those shown above.
B030-045E.indd 32-33
Nominal Bearing Outside Diameter D (mm)
Variation of Bearing Outside Surface Generatrix Inclination with Flange Backface S D1
Notes (1) 2.5 mm is included
With flange and extended inner ring
B 32
Units : μm
(2) Flange Width Tolerances and Running Accuracies Related to Flange
bearings are
LIMITING SPEEDS The limiting speeds listed in the bearing tables should be adjusted depending on the bearing toad conditions. Also, higher speeds are attainable by making changes in the lubrication method, cage design, etc. Refer to Page A37 for detailed information. B 33
11/20/13 4:54:15 PM
EXTRA SMALL BALL BEARINGS · MINIATURE BALL BEARINGS Metric Design Bore Diameter
1 – 4 mm B
B1 r
r1 r1
r jD
jd
jD
jd
Boundary Dimensions
1
1.2 1.5
2
2.5
3
4
3 3 4 4 4 5 6 5 5 6 6 7 7 6 7 8 8 6 7 8 8 9 9 10 13 7 7 8 9 10 11 12 13 16
B 1.0 1.5 1.6 1.8 1.2 2.0 2.5 1.5 2.0 2.3 2.5 2.5 2.8 1.8 2.5 2.5 2.8 2.0 2.0 2.5 3.0 2.5 3.0 4.0 5.0 2.0 — 2.0 2.5 3.0 4.0 4.0 5.0 5.0
B1 — — — 2.5 2.0 2.6 3.0 2.3 2.5 3.0 2.5 3.0 3.5 2.6 3.5 — 4.0 2.5 3.0 — 4.0 4.0 5.0 4.0 5.0 — 2.5 3.0 4.0 4.0 4.0 4.0 5.0 5.0
(N)
r (1)
r 1(1)
min.
min.
0.05 0.05 0.10 0.10 0.05 0.15 0.15 0.08 0.10 0.15 0.15 0.15 0.15 0.08 0.15 0.20 0.15 0.10 0.10 0.15 0.15 0.20 0.15 0.15 0.20 0.10 — 0.15 (0.15) 0.20 0.15 0.20 0.20 0.30
— — — 0.10 0.05 0.15 0.15 0.08 0.10 0.15 0.15 0.15 0.15 0.08 0.15 — 0.15 0.10 0.10 — 0.15 0.15 0.15 0.15 0.20 — 0.10 0.10 (0.15) 0.15 0.15 0.20 0.20 0.30
ra
rb jD b
jd a
jD a
Limiting Speeds
Basic Load Ratings
(mm)
D
rb
jd b
Shielded Type ZZ · ZZ1
Open Type
d
ra
Cr 80 80 138 138 112 237 330 169 187 330 330 385 385 208 385 560 550 208 390 560 560 570 570 630 1 300 310 255 395 640 710 960 960 1 300 1 730
C 0r 23 23 35 35 33 69 98 50 58 98 98 127 127 74 127 179 175 74 130 179 179 187 187 218 485 115 107 139 225 270 345 345 485 670
Cr 8 8 14 14 11 24 34 17 19 34 34 39 39 21 39 57 56 21 40 57 57 58 58 64 133 32 26 40 65 73 98 98 133 177
C 0r 2.5 2.5 3.5 3.5 3.5 7 10 5 6 10 10 13 13 7.5 13 18 18 7.5 13 18 18 19 19 22 49 12 11 14 23 28 35 35 49 68
Bearing Numbers
Mass
Abutment and Fillet Dimensions
(g)
(mm)
(min –1)
{kgf} Grease
Oil
Open Z · ZZ
Open Z
130 000 130 000 100 000 110 000 100 000 85 000 75 000 85 000 85 000 75 000 75 000 63 000 63 000 71 000 63 000 60 000 60 000 71 000 63 000 60 000 60 000 56 000 56 000 50 000 40 000 60 000 60 000 56 000 53 000 50 000 48 000 48 000 40 000 36 000
150 000 150 000 120 000 130 000 120 000 100 000 90 000 100 000 100 000 90 000 90 000 75 000 75 000 80 000 75 000 67 000 71 000 80 000 75 000 67 000 67 000 67 000 67 000 60 000 48 000 67 000 71 000 67 000 63 000 60 000 56 000 56 000 48 000 43 000
Open
681 MR 31 691 MR 41 X 681 X 691 X 601 X 682 MR 52 B 692 MR 62 MR 72 602 682 X 692 X MR 82 X 602 X MR 63 683 A MR 83 693 MR 93 603 623 633 MR 74 — MR 84 684 A MR 104 B 694 604 624 634
Shielded
MR
MR MR MR
MR
MR
MR MR MR
— — — 41 681 691 601 682 52 692 62 72 602 682 692 — 602 63 683 — 693 93 603 623 633 — 74 84 684 104 694 604 624 634
XZZ XZZ XZZ XZZ ZZ BZZ ZZ ZZ ZZ ZZ XZZ XZZ XZZ ZZ AZZ ZZ ZZ ZZ ZZ ZZ ZZ ZZ AZZ BZZ ZZ ZZ ZZ ZZ1
Sealed
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
da
db
Da
Db
ra
rb
min.
max.
max.
min.
max.
max.
approx. Open Shielded
1.4 1.4 1.8 2.0 1.9 2.7 2.7 2.6 2.8 3.2 3.2 3.2 3.2 3.1 3.7 4.1 3.7 3.8 3.8 4.2 4.2 4.6 4.2 4.2 4.6 4.8 — 5.2 4.8 5.6 5.2 5.6 5.6 6.0
— — — 1.9 2.1 2.5 3.0 2.7 2.7 3.0 3.0 3.8 3.8 3.7 3.8 — 4.1 3.7 4.0 — 4.3 4.3 4.3 4.3 6.0 — 4.8 5.0 5.2 5.9 5.6 5.6 6.0 7.5
02.6 02.6 03.2 03.2 03.6 03.8 04.8 04.4 04.2 04.8 04.8 05.8 05.8 05.4 05.8 06.4 06.8 05.2 06.2 06.8 06.8 07.4 07.8 08.8 11.4 06.2 — 06.8 08.2 08.4 09.8 10.4 11.4 14.0
— — — 03.5 03.6 04.3 05.4 04.2 04.4 05.4 05.2 06.2 06.2 05.4 06.2 — 07.0 05.4 06.4 — 07.3 07.9 07.9 08.0 11.3 — 06.3 07.4 08.1 08.8 09.9 09.9 11.3 13.8
0.05 0.05 0.10 0.10 0.05 0.15 0.15 0.08 0.10 0.15 0.15 0.15 0.15 0.08 0.15 0.20 0.15 0.10 0.10 0.15 0.15 0.20 0.15 0.15 0.20 0.10 — 0.15 0.10 0.20 0.15 0.20 0.20 0.30
— — — 0.10 0.05 0.15 0.15 0.08 0.10 0.15 0.15 0.15 0.15 0.08 0.15 — 0.15 0.10 0.10 — 0.15 0.15 0.15 0.15 0.20 — 0.10 0.10 0.10 0.15 0.15 0.20 0.20 0.30
0.03 0.04 0.09 0.10 0.07 0.17 0.33 0.12 0.16 0.28 0.30 0.45 0.51 0.23 0.41 0.56 0.63 0.20 0.32 0.54 0.61 0.73 0.87 1.65 3.38 0.22 — 0.36 0.63 1.04 1.7 2.25 3.03 5.24
— — — 0.14 0.11 0.20 0.38 0.17 0.23 0.38 0.29 0.49 0.58 0.29 0.55 — 0.83 0.27 0.45 — 0.83 1.18 1.45 1.66 3.33 — 0.29 0.56 1.01 1.42 1.75 2.29 3.04 5.21
Note (1) The values in parentheses are not based on ISO 15. Remarks When using bearings with a rotating outer ring, please contact NSK if they are shielded.
B 34
B030-045E.indd 34-35
B 35
11/20/13 4:54:16 PM
EXTRA SMALL BALL BEARINGS · MINIATURE BALL BEARINGS Metric Design Bore Diameter
5 – 9 mm B1
B
B1
r r1 jd
jd
5
6
7
8
9
8 8 9 10 11 11 13 14 16 19 10 12 13 15 17 19 22 11 13 14 17 19 22 26 12 14 16 19 22 24 28 17 20 24 26 30
2.0 — 2.5 3.0 — 3.0 4.0 5.0 5.0 6.0 2.5 3.0 3.5 5.0 6.0 6.0 7.0 2.5 3.0 3.5 5.0 6.0 7.0 9.0 2.5 3.5 4.0 6.0 7.0 8.0 9.0 4.0 6.0 7.0 8.0 10.00
jD
B1
Non-Contact Sealed Type VV
— 2.5 3.0 4.0 4.0 5.0 4.0 5.0 5.0 6.0 3.0 4.0 5.0 5.0 6.0 6.0 7.0 3.0 4.0 5.0 5.0 6.0 7.0 9.0 3.5 4.0 5.0 6.0 7.0 8.0 9.0 5.0 6.0 7.0 8.0 10.00
(N)
r (1)
r1(1)
min.
min.
0.10 — — 0.10 0.15 0.15 0.15 0.15 — 0.15 0.15 0.15 0.20 0.20 0.20 0.20 0.30 0.30 0.30 0.30 0.15 0.10 0.20 0.15 0.15 0.15 0.20 0.20 0.30 0.30 0.30 0.30 0.30 0.30 0.15 0.10 0.20 0.15 0.15 0.15 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.15 0.10 0.20 0.15 0.20 0.20 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.20 0.20 0.30 0.30 0.30 0.30 (0.6)0 (0.6)0 0.60 0.60
jD
jd
Cr 310 278 430 430 715 715 1 080 1 330 1 730 2 340 495 715 1 080 1 730 2 260 2 340 3 300 455 540 1 170 1 610 2 340 3 300 4 550 545 820 1 610 2 240 3 300 3 350 4 550 1 330 1 720 3 350 4 550 5 100
{kgf}
C 0r 120 131 168 168 276 281 430 505 670 885 218 292 440 670 835 885 1 370 201 276 510 710 885 1 370 1 970 274 385 710 910 1 370 1 430 1 970 665 840 1 430 1 970 2 390
Cr 31 28 44 44 73 73 110 135 177 238 51 73 110 177 231 238 335 47 55 120 164 238 335 465 56 83 164 228 335 340 465 136 175 340 465 520
jd
C 0r 12 13 17 17 28 29 44 52 68 90 22 30 45 68 85 90 140 21 28 52 73 90 140 201 28 39 73 93 140 146 201 68 86 146 201 244
ra
rb
ra
rb jD b
jd a
jD a
jd b
Contact Sealed Type DD Limiting Speeds (min –1)
Basic Load Ratings
(mm)
B
r1
Shielded Type ZZ · ZZ1
Boundary Dimensions
D
r1
r1
jD
Open Type
d
r1
r1
r jD
B1
Grease Open Z · ZZ V · VV
53 000 53 000 50 000 50 000 48 000 45 000 43 000 40 000 36 000 32 000 45 000 43 000 40 000 40 000 38 000 32 000 30 000 43 000 40 000 40 000 36 000 36 000 30 000 28 000 40 000 38 000 36 000 36 000 34 000 28 000 28 000 36 000 34 000 32 000 28 000 24 000
Bearing Numbers
D · DD
— — — — — — 40 000 38 000 32 000 30 000 — 40 000 38 000 36 000 34 000 30 000 28 000 — — 34 000 28 000 32 000 28 000 22 000 — 32 000 28 000 28 000 28 000 24 000 22 000 24 000 24 000 24 000 22 000 —
Open Z
63 000 63 000 60 000 60 000 56 000 53 000 50 000 50 000 43 000 40 000 53 000 50 000 50 000 45 000 45 000 40 000 36 000 50 000 48 000 45 000 43 000 43 000 36 000 34 000 48 000 45 000 43 000 43 000 40 000 34 000 34 000 43 000 40 000 38 000 34 000 30 000
Mass
Abutment and Fillet Dimensions
Oil
(g)
(mm) Open
MR 85 — MR 95 MR 105 — 685 695 605 625 635 MR 106 MR 126 686 A 696 606 626 636 MR 117 MR 137 687 697 607 627 637 MR 128 MR 148 688 A 698 608 628 638 689 699 609 629 639
Shielded
MR MR MR MR
MR MR
MR MR
MR MR
— 85 95 105 115 685 695 605 625 635 106 126 686 696 606 626 636 117 137 687 697 607 627 637 128 148 688 698 608 628 638 689 699 609 629 639
ZZ ZZ1 ZZ ZZ ZZ ZZ ZZ ZZ1 ZZ1 ZZ1 ZZ AZZ ZZ1 ZZ ZZ1 ZZ ZZ ZZ ZZ1 ZZ1 ZZ1 ZZ ZZ1 ZZ1 ZZ AZZ1 ZZ ZZ ZZ ZZ1 ZZ1 ZZ1 ZZ ZZ ZZ
Sealed
— — — — VV — VV — VV VV — — VV VV VV VV VV — — VV VV VV VV VV — VV VV VV VV VV VV VV VV VV VV VV
— — — — — — DD DD DD DD — DD DD DD DD DD DD — — DD DD DD DD DD — DD DD DD DD DD DD DD DD DD DD —
da
db
Da
Db
ra
rb
min.
max.
max.
min.
max.
max.
approx. Open Shielded
05.8 — 06.2 06.2 — 06.2 06.6 06.6 07.0 07.0 07.2 07.6 07.2 07.6 08.0 08.0 08.0 08.2 08.6 08.2 09.0 09.0 09.0 09.0 09.2 09.6 09.6 10.0 10.0 10.0 10.0 10.6 11.0 11.0 11.0 13.0
— 05.8 06.0 06.0 06.3 06.2 06.6 06.9 07.5 08.5 07.0 07.2 07.4 07.9 08.2 08.5 10.5 08.0 09.0 08.5 10.2 09.1 10.5 12.8 09.0 09.2 10.2 10.0 10.5 12.0 12.8 11.5 12.0 12.0 12.8 16.1
07.2 — 07.8 08.8 — 09.8 11.4 12.4 14.0 17.0 08.8 10.4 11.8 13.4 15.0 17.0 20.0 09.8 11.4 12.8 15.0 17.0 20.0 24.0 10.8 12.4 14.4 17.0 20.0 22.0 26.0 15.4 18.0 22.8 24.0 26.0
— 07.4 08.2 08.4 09.8 09.9 11.2 12.2 13.8 16.5 09.3 10.9 11.7 13.3 14.8 16.5 19.0 10.5 11.6 12.7 14.8 16.5 19.0 22.8 11.3 12.8 14.2 16.5 19.0 20.5 22.8 15.2 17.2 20.5 22.8 25.6
0.10 — 0.15 0.15 — 0.15 0.20 0.20 0.30 0.30 0.15 0.20 0.15 0.20 0.30 0.30 0.30 0.15 0.20 0.15 0.30 0.30 0.30 0.30 0.15 0.20 0.20 0.30 0.30 0.30 0.30 0.20 0.30 0.30 0.30 0.60
— 0.10 0.15 0.15 0.15 0.15 0.20 0.20 0.30 0.30 0.10 0.15 0.15 0.20 0.30 0.30 0.30 0.10 0.15 0.15 0.30 0.30 0.30 0.30 0.10 0.15 0.20 0.30 0.30 0.30 0.30 0.20 0.30 0.30 0.30 0.60
00.26 — 00.50 00.95 — 01.20 02.45 03.54 04.95 08.56 00.56 01.27 01.91 03.88 05.97 08.15 14.00 00.62 01.58 02.13 05.26 07.67 12.70 24.00 00.71 01.86 03.12 07.23 12.10 17.20 28.30 03.53 08.45 14.50 19.50 36.50
— 00.34 00.58 01.29 01.49 01.96 02.50 03.48 04.86 08.34 00.68 01.74 02.69 03.72 06.08 07.94 14.00 00.72 02.02 02.97 05.12 07.51 12.90 25.00 00.97 02.16 04.02 07.18 12.20 17.40 28.60 04.43 08.33 14.70 19.30 36.00
Note (1) The values in parentheses are not based on ISO 15. Remarks 1. When using bearings with a rotating outer ring, please contact NSK if they are sealed or shielded. 2. Bearings with snap rings are also available, please contact NSK.
B 36
B030-045E.indd 36-37
B 37
11/20/13 4:54:17 PM
EXTRA SMALL BALL BEARINGS · MINIATURE BALL BEARINGS Metric Design With Flange Bore Diameter 1 – 4 mm B
B1
C1
r
r1
r
r1
Boundary Dimensions (mm)
D
D1
D2
1.0 1.6
B1 — —
rb jda
jdb
C1 0.3 0.5
C2 — —
r (1) r1(1)
Basic Load Ratings
Limiting Speeds
(N)
(min –1) Grease
Cr
{kgf}
C 0r
Cr
C 0r
Open Z · ZZ
Bearing Numbers
Abutment and Fillet Dimensions
Mass (g)
(mm) Oil
Open
Open Z
min.
min.
0.05 0.10
— —
80 140
23 36
8 14
2.5 3.5
130 000 100 000
150 000 120 000
F 681 F 691
Shielded
— —
db
ra
rb
min.
max.
max.
max.
approx. Open Shielded
1.4 1.8
— —
0.05 0.10
— —
0.04 0.14
03.8 05.0
1.2
4
04.8
—
1.8
—
0.4
—
0.10
—
138
35
14
3.5
110 000
130 000
MF 41 X
—
—
2.0
—
0.10
—
0.12
—
1.5
4 5 6
05.0 06.5 07.5
05.0 06.5 07.5
1.2 2.0 2.5
2.0 2.6 3.0
0.4 0.6 0.6
0.6 0.8 0.8
0.05 0.15 0.15
0.05 0.15 0.15
112 237 330
33 69 98
11 24 34
3.5 7 10
100 000 85 000 75 000
120 000 100 000 90 000
F 681 X F 691 X F 601 X
F 681 XZZ F 691 XZZ F 601 XZZ
— — —
— — —
1.9 2.7 2.7
2.1 2.5 3.0
0.05 0.15 0.15
0.05 0.15 0.15
0.09 0.23 0.42
0.14 0.28 0.52
2
5 5 6
06.1 06.2 07.5
06.1 06.2 07.5
1.5 2.0 2.3
2.3 2.5 3.0
0.5 0.6 0.6
0.6 0.6 0.8
0.08 0.10 0.15
0.08 0.10 0.15
169 187 330
50 58 98
17 19 34
5 6 10
85 000 85 000 75 000
100 000 100 000 90 000
F 682 MF 52 B F 692
F 682 ZZ MF 52 BZZ F 692 ZZ
— — —
— — —
2.6 2.8 3.2
2.7 2.7 3.0
0.08 0.10 0.15
0.08 0.10 0.15
0.16 0.21 0.35
0.22 0.27 0.48
6 7 7
07.2 08.2 08.5
— 08.2 08.5
2.5 2.5 2.8
— 3.0 3.5
0.6 0.6 0.7
— 0.6 0.9
0.15 0.15 0.15
— 0.15 0.15
330 385 385
98 127 127
34 39 39
10 13 13
75 000 63 000 63 000
90 000 75 000 75 000
MF 62 MF 72 F 602
— MF 72 ZZ F 602 ZZ
— — —
— — —
3.2 3.2 3.2
— 3.8 3.1
0.15 0.15 0.15
— 0.15 0.15
0.36 0.52 0.60
— 0.56 0.71
2.5
6 7 8 8
07.1 08.5 09.2 09.5
07.1 08.5 — 09.5
1.8 2.5 2.5 2.8
2.6 3.5 — 4.0
0.5 0.7 0.6 0.7
0.8 0.9 — 0.9
0.08 0.15 0.20 0.15
0.08 0.15 — 0.15
208 385 560 550
74 127 179 175
21 39 57 56
7.5 13 18 18
71 000 63 000 60 000 60 000
80 000 75 000 67 000 71 000
F F MF F
682 X 692 X 82 X 602 X
F 682 XZZ F 692 XZZ — F 602 XZZ
— — — —
— — — —
3.1 3.7 4.1 3.7
3.7 3.8 — 3.5
0.08 0.15 0.20 0.15
0.08 0.15 — 0.15
0.25 0.51 0.62 0.74
0.36 0.68 — 0.98
3
6 7 8
07.2 08.1 09.2
07.2 08.1 —
2.0 2.0 2.5
2.5 3.0 —
0.6 0.5 0.6
0.6 0.8 —
0.10 0.10 0.15
0.10 0.10 —
208 390 560
74 130 179
21 40 57
7.5 13 18
71 000 63 000 60 000
80 000 75 000 67 000
MF 63 F 683 A MF 83
MF 63 ZZ F 683 AZZ —
— — —
— — —
3.8 3.8 4.2
3.7 4.0 —
0.10 0.10 0.15
0.10 0.10 —
0.27 0.37 0.56
0.33 0.53 —
8 9 9 10 13
09.5 10.2 10.5 11.5 15.0
09.5 10.6 10.5 11.5 15.0
3.0 2.5 3.0 4.0 5.0
4.0 4.0 5.0 4.0 5.0
0.7 0.6 0.7 1.0 1.0
0.9 0.8 1.0 1.0 1.0
0.15 0.20 0.15 0.15 0.20
0.15 0.15 0.15 0.15 0.20
560 570 570 630 1 300
179 187 187 218 485
57 58 58 64 133
18 19 19 22 49
60 000 56 000 56 000 50 000 36 000
67 000 67 000 67 000 60 000 43 000
F MF F F F
F MF F F F
ZZ ZZ ZZ ZZ ZZ
— — — — —
— — — — —
4.2 4.6 4.2 4.2 4.6
4.3 4.3 4.3 4.3 6.0
0.15 0.20 0.15 0.15 0.20
0.15 0.15 0.15 0.15 0.20
0.70 0.81 1.00 1.85 3.73
0.97 1.34 1.63 1.86 3.59
7 7 8 9
08.2 — 09.2 10.3
— 08.2 09.2 10.3
2.0 — 2.0 2.5
— 2.5 3.0 4.0
0.6 — 0.6 0.6
— 0.10 — 0.6 — 0.10 0.6 0.15 0.10 1.0 (0.15) (0.15)
310 255 395 640
115 107 139 225
32 26 40 65
12 11 14 23
60 000 60 000 56 000 53 000
67 000 71 000 67 000 63 000
MF 74 — MF 84 F 684
— MF 74 ZZ MF 84 ZZ F 684 ZZ
— — — —
— — — —
4.8 — 5.2 4.8
— 4.8 5.0 5.2
0.10 — 0.15 0.10
— 0.10 0.10 0.10
0.29 — 0.44 0.70
— 0.35 0.63 1.14
10 11 12
11.2 12.5 13.5
11.6 12.5 13.5
3.0 4.0 4.0
4.0 4.0 4.0
0.6 1.0 1.0
0.8 1.0 1.0
0.20 0.15 0.20
0.15 0.15 0.20
710 960 960
270 345 345
73 98 98
28 35 35
50 000 48 000 48 000
60 000 56 000 56 000
MF 104 B F 694 F 604
MF 104 BZZ F 694 ZZ F 604 ZZ
— — —
— — —
5.6 5.2 5.6
5.9 5.6 5.6
0.20 0.15 0.20
0.15 0.15 0.20
1.13 1.91 2.53
1.59 1.96 2.53
13 16
15.0 18.0
15.0 18.0
5.0 5.0
5.0 5.0
1.0 1.0
1.0 1.0
0.20 0.30
0.20 0.30
1 300 1 730
485 670
133 177
49 68
40 000 36 000
48 000 43 000
F 624 F 634
F 624 ZZ F 634 ZZ1
— —
— —
5.6 6.0
6.0 7.5
0.20 0.30
0.20 0.30
3.38 5.73
3.53 5.62
—
693 93 603 623 633
— —
da
3 4
693 93 603 623 633
— —
Sealed
1
4
— —
B
jd jD 2
Shielded Type ZZ · ZZ1
Open Type
d
ra
jD
jd jD 1
jD
C2
— —
Note (1) The values in parentheses are not based on ISO 15. Remarks When using bearings with a rotating outer ring, please contact NSK if they are shielded.
B 38
B030-045E.indd 38-39
B 39
11/20/13 4:54:19 PM
EXTRA SMALL BALL BEARINGS · MINIATURE BALL BEARINGS Metric Design With Flange Bore Diameter 5 – 9 mm B
B1
C1
B1
C2
r
r1
r1
r1
r
r1
r1
r1
Boundary Dimensions
5
6
7
8
9
D1
D2
B
(N)
B1
C1
C2
r
r1
min.
min.
Cr
rb jda
Limiting Speeds (min –1)
{kgf}
C 0r
ra
jdb
Contact Sealed Type DD
Basic Load Ratings
(mm)
C2
jd jD2
jD
Non-Contact Sealed Type VV
Shielded Type ZZ · ZZ1
Open Type
D
jd jD2
jd jD2 jD
jd jD1 jD
jD
d
B1
C2
C r C 0r
Grease Open Z · ZZ V · VV
Abutment and Fillet Dimensions (mm)
Bearing Numbers
Oil
D · DD
Open Z
Open
8 8 9 10
09.2 — 10.2 11.2
— 09.2 10.2 11.6
2.0 — 2.5 3.0
— 2.5 3.0 4.0
0.6 — 0.6 0.6
— 0.6 0.6 0.8
0.10 — 0.15 0.15
— 0.10 0.15 0.15
310 278 430 430
120 131 168 168
31 28 44 44
12 13 17 17
53 000 53 000 50 000 50 000
— — — —
63 000 63 000 60 000 60 000
MF 85 — MF 95 MF 105
11 13 14
12.5 15.0 16.0
12.5 15.0 16.0
3.0 4.0 5.0
5.0 4.0 5.0
0.8 1.0 1.0
1.0 1.0 1.0
0.15 0.20 0.20
0.15 0.20 0.20
715 1 080 1 330
281 430 505
73 110 135
29 44 52
45 000 43 000 40 000
— 40 000 38 000
53 000 50 000 50 000
16 19
18.0 22.0
18.0 22.0
5.0 6.0
5.0 6.0
1.0 1.5
1.0 1.5
0.30 0.30
0.30 0.30
1 730 2 340
670 885
177 238
68 90
36 000 32 000
32 000 30 000
10 12 13
11.2 13.2 15.0
11.2 13.6 15.0
2.5 3.0 3.5
3.0 4.0 5.0
0.6 0.6 1.0
0.6 0.8 1.1
0.15 0.20 0.15
0.10 0.15 0.15
495 715 1 080
218 292 440
51 73 110
22 30 45
45 000 43 000 40 000
15 17 19 22
17.0 19.0 22.0 25.0
17.0 19.0 22.0 25.0
5.0 6.0 6.0 7.0
5.0 6.0 6.0 7.0
1.2 1.2 1.5 1.5
1.2 1.2 1.5 1.5
0.20 0.30 0.30 0.30
0.20 0.30 0.30 0.30
1 730 670 2 260 835 2 340 885 3 300 1 370
177 68 231 85 238 90 335 140
11 13 14
12.2 14.2 16.0
12.2 14.6 16.0
2.5 3.0 3.5
3.0 4.0 5.0
0.6 0.6 1.0
0.6 0.8 1.1
0.15 0.20 0.15
0.10 0.15 0.15
455 540 1 170
47 55 120
17 19 22
19.0 22.0 25.0
19.0 22.0 25.0
5.0 6.0 7.0
5.0 6.0 7.0
1.2 1.5 1.5
1.2 1.5 1.5
0.30 0.30 0.30
0.30 0.30 0.30
12 14 16
13.2 15.6 18.0
13.6 15.6 18.0
2.5 3.5 4.0
3.5 4.0 5.0
0.6 0.8 1.0
0.8 0.8 1.1
0.15 0.20 0.20
19 22
22.0 25.0
22.0 25.0
6.0 7.0
6.0 7.0
1.5 1.5
1.5 1.5
17 20
19.0 23.0
19.0 23.0
4.0 6.0
5.0 6.0
1.0 1.5
1.1 1.5
Shielded
Sealed
Mass (g)
da
db
ra
rb
min.
max.
max.
max.
approx. Open Shielded
— MF 85 ZZ MF 95 ZZ1 MF 105 ZZ
— — — —
— — — —
05.8 — 06.2 06.2
— 05.8 06.0 06.0
0.10 — 0.15 0.15
— 0.10 0.15 0.15
00.33 — 00.59 01.05
— 00.41 00.66 01.46
F 685 F 695 F 605
F 685 ZZ F 695 ZZ F 605 ZZ
— VV —
— DD DD
06.2 06.6 06.6
06.2 06.6 06.9
0.15 0.20 0.20
0.15 0.20 0.20
01.37 02.79 03.90
02.18 02.84 03.85
43 000 40 000
F 625 F 635
F 625 ZZ1 F 635 ZZ1
VV VV
DD DD
07.0 07.0
07.5 08.5
0.30 0.30
0.30 0.30
05.37 09.49
05.27 09.49
— 40 000 38 000
53 000 50 000 50 000
MF 106 MF 126 F 686 A
MF 106 ZZ1 MF 126 ZZ F 686 AZZ
— — VV
— DD DD
07.2 07.6 07.2
07.0 07.2 07.4
0.15 0.20 0.15
0.10 0.15 0.15
00.65 01.38 02.25
00.77 01.94 03.04
40 000 38 000 32 000 30 000
36 000 34 000 30 000 28 000
45 000 45 000 40 000 36 000
ZZ1 ZZ ZZ1 ZZ
VV VV VV VV
DD DD DD DD
07.6 08.0 08.0 08.0
07.9 08.2 08.5 10.5
0.20 0.30 0.30 0.30
0.20 0.30 0.30 0.30
04.34 06.58 09.09 14.60
04.26 06.61 09.09 14.70
21 28 52
43 000 40 000 40 000
— — 34 000
50 000 48 000 45 000
MF 117 MF 137 F 687
MF 117 ZZ MF 137 ZZ F 687 ZZ1
— — VV
— — DD
08.2 08.6 08.2
08.0 09.0 08.5
0.15 0.20 0.15
0.10 0.15 0.15
00.72 01.70 02.48
00.82 02.23 03.37
1 610 715 2 340 885 3 300 1 370
164 73 238 90 335 140
36 000 36 000 30 000
28 000 32 000 28 000
43 000 43 000 36 000
F 697 F 607 F 627
F 697 ZZ1 F 607 ZZ1 F 627 ZZ
VV VV VV
DD DD DD
09.0 09.0 09.0
10.2 09.1 10.5
0.30 0.30 0.30
0.30 0.30 0.30
05.65 08.66 14.20
05.65 08.66 14.20
0.10 0.15 0.20
545 820 1 610
56 83 164
28 39 73
40 000 38 000 36 000
— 32 000 30 000
48 000 45 000 43 000
MF 128 MF 148 F 688 A
MF 128 ZZ1 MF 148 ZZ F 688 AZZ
— VV VV
— DD DD
09.2 09.6 09.6
09.0 09.2 10.2
0.15 0.20 0.20
0.10 0.15 0.20
00.82 02.09 03.54
01.15 02.39 04.47
0.30 0.30
0.30 0.30
2 240 910 3 300 1 370
228 93 335 140
36 000 34 000
28 000 28 000
43 000 40 000
F 698 F 608
F 698 ZZ F 608 ZZ
VV VV
DD DD
10.0 10.0
10.0 10.5
0.30 0.30
0.30 0.30
08.35 13.40
08.30 13.50
0.20 0.30
0.20 0.30
1 330 1 720
136 175
36 000 34 000
24 000 24 000
43 000 40 000
F 689 F 699
F 689 ZZ1 F 699 ZZ1
VV VV
DD DD
10.6 11.0
11.5 12.0
0.20 0.30
0.20 0.30
03.97 09.51
04.91 09.51
201 276 510
274 385 710
665 840
68 86
F F F F
696 606 626 636
F F F F
696 606 626 636
Remarks When using bearings with a rotating outer ring, please contact NSK if they are shielded.
B 40
B030-045E.indd 40-41
B 41
11/20/13 4:54:20 PM
EXTRA SMALL BALL BEARINGS · MINIATURE BALL BEARINGS Inch Design Bore Diameter
1.016 – 9.525 mm B
B1 r
r r
r
jD
jd
jD
jd
Boundary Dimensions
B
ra
ra jD b
jd a
jDa
Limiting Speeds
Basic Load Ratings
(mm)
D
ra
jd b
Shielded Type ZZ · ZZS
Open Type
d
ra
(N)
B1
r
Cr
C 0r
Cr
Bearing
Numbers
C 0r
min.
Mass
Abutment and Fillet Dimensions
(g)
(mm)
(min –1)
{kgf} Grease
Oil
Open Z · ZZ
Open Z
Open
Shielded
db
Da
Db
ra
min.
max.
max.
min.
max.
approx. Open Shielded
1.016
3.175
1.191
—
0.1
80
23
8
2.5
130 000
150 000
R 09
01.9
—
02.3
—
0.1
0.04
—
1.191
3.967
1.588
2.380
0.1
138
35
14
3.5
110 000
130 000
R0
R 0 ZZ
02.0
01.9
03.1
03.5
0.1
0.09
00.11
1.397
4.762
1.984
2.779
0.1
231
66
24
6.5
90 000
110 000
R1
R 1 ZZ
02.2
02.3
03.9
04.1
0.1
0.15
00.19
1.984
6.350
2.380
3.571
0.1
310
108
32
11
67 000
80 000
R 1-4
R 1-4 ZZ
02.8
03.9
05.5
05.9
0.1
0.35
00.50
2.380
4.762 4.762 7.938
1.588 — 2.779
— 2.380 3.571
0.1 0.1 0.15
188 143 550
60 52 175
19 15 56
6 5.5 18
80 000 80 000 60 000
95 000 95 000 71 000
R 133 — R 1-5
— R 133 ZZS R 1-5 ZZ
03.2 — 03.6
— 03.0 04.1
03.9 — 06.7
— 04.2 07.0
0.1 0.1 0.15
0.10 — 0.60
— 00.13 00.72
3.175
6.350 7.938 9.525
2.380 2.779 2.779
2.779 3.571 3.571
0.1 0.1 0.15
283 560 640
95 179 225
29 57 65
9.5 18 23
67 000 60 000 53 000
80 000 67 000 63 000
R 144 R 2-5 R 2-6
R 144 ZZ R 2-5 ZZ R 2-6 ZZS
04.0 04.0 04.4
03.9 04.3 04.6
05.5 07.1 08.3
05.9 07.3 08.2
0.1 0.1 0.15
0.25 0.55 0.96
00.27 00.72 01.13
9.525 12.700
3.967 4.366
3.967 4.366
0.3 0.3
630 640
218 225
64 65
22 23
56 000 53 000
67 000 63 000
R2 R 2A
R 2 ZZ R 2A ZZ
05.2 05.2
04.8 04.6
07.5 10.7
08.0 08.2
0.3 0.3
1.36 3.30
01.39 03.23
3.967
7.938
2.779
3.175
0.1
360
149
37
15
53 000
63 000
R 155
R 155 ZZS
04.8
05.5
07.1
07.3
0.1
0.51
00.56
4.762
7.938 9.525 12.700
2.779 3.175 3.967
3.175 3.175 4.978
0.1 0.1 0.3
360 710 1 300
149 270 485
37 73 133
15 28 49
53 000 50 000 43 000
63 000 60 000 53 000
R 156 R 166 R3
R 156 ZZS R 166 ZZ R 3 ZZ
05.6 05.6 06.8
05.5 05.9 06.5
07.1 08.7 10.7
07.3 08.8 11.2
0.1 0.1 0.3
0.39 0.81 2.21
00.42 00.85 02.79
6.350
9.525 12.700
3.175 3.175
3.175 4.762
0.1 0.15
420 1 080
204 440
43 110
21 45
48 000 40 000
56 000 50 000
R 168B R 188
R 168 BZZ R 188 ZZ
07.2 07.6
07.0 07.4
08.7 11.5
08.9 11.6
0.1 0.15
0.58 1.53
00.62 02.21
15.875 19.050
4.978 5.558
4.978 7.142
0.3 0.4
1 610 660 2 620 1 060
164 68 267 108
38 000 36 000
45 000 43 000
R 4B R 4AA
R 4B ZZ R 4AA ZZ
08.4 09.4
08.4 09.0
13.8 16.0
13.8 16.6
0.3 0.4
4.50 7.48
04.43 09.17
7.938
12.700
3.967
3.967
0.15
28
40 000
48 000
R 1810
R 1810 ZZ
09.2
09.0
11.5
11.6
0.15
1.56
01.48
9.525
22.225
5.558
7.142
0.4
340 144
32 000
38 000
R6
R 6 ZZ
12.6
11.9
19.2
20.0
0.4
9.02
11.00
540
276
3 350 1 410
55
—
da
Remarks 1. When using bearings with a rotating outer ring, please contact NSK if they are shielded. 2. Bearings with double shields (ZZ, ZZS) are also available with single shields (Z, ZS).
B 42
B030-045E.indd 42-43
B 43
11/20/13 4:54:22 PM
EXTRA SMALL BALL BEARINGS · MINIATURE BALL BEARINGS Inch Design With Flange Bore Diameter 1.191 – 9.525 mm B
B1
C1
r
r
r
r jd jD 1
Boundary Dimensions
D1
B
(N)
B1
Limiting Speeds
Basic Load Ratings
(mm)
D
C1
C2
r
Cr
C 0r
Cr
C 0r
3.175
3.967 4.762
6.350
7.938 9.525
3.967 4.762 6.350 4.762 4.762 7.938 6.350 7.938 9.525 9.525 7.938 7.938 9.525 12.700 9.525 12.700 15.875 12.700 22.225
5.156 5.944 7.518 5.944 5.944 9.119 7.518 9.119 10.719 11.176 9.119 9.119 10.719 14.351 10.719 13.894 17.526 13.894 24.613
1.588 1.984 2.380 1.588 — 2.779 2.380 2.779 2.779 3.967 2.779 2.779 3.175 4.978 3.175 3.175 4.978 3.967 7.142
2.380 2.779 3.571 — 2.380 3.571 2.779 3.571 3.571 3.967 3.175 3.175 3.175 4.978 3.175 4.762 4.978 3.967 7.142
0.330 0.580 0.580 0.460 — 0.580 0.580 0.580 0.580 0.760 0.580 0.580 0.580 1.070 0.580 0.580 1.070 0.790 1.570
0.790 0.790 0.790 — 0.790 0.790 0.790 0.790 0.790 0.760 0.910 0.910 0.790 1.070 0.910 1.140 1.070 0.790 1.570
0.1 0.1 0.1 0.1 0.1 0.15 0.1 0.1 0.15 0.3 0.1 0.1 0.1 0.3 0.1 0.15 0.3 0.15 0.4
138 35 231 66 310 108 188 60 143 52 550 175 283 95 560 179 640 225 630 218 360 149 360 149 710 270 1 300 485 420 204 1 080 440 1 610 660 540 276 3 350 1 410
14 3.5 24 6.5 32 11 19 6 15 5.5 56 18 29 9.5 57 18 65 23 64 22 37 15 37 15 73 28 133 49 43 21 110 45 164 68 55 28 340 144
Bearing Numbers
(min –1)
{kgf}
min.
1.191 1.397 1.984 2.380
jd b
jd a
Shielded Type ZZ · ZZS
Open Type
d
ra
ra
jD
jd jD 1
jD
C2
Grease
Oil
Open Z · ZZ
Open Z
110 90 67 80 80 60 67 60 53 56 53 53 50 43 48 40 38 40 32
000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000
130 110 80 95 95 71 80 67 63 67 63 63 60 53 56 50 45 48 38
000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000
Open
FR 0 FR 1 FR 1-4 FR 133 — FR 1-5 FR 144 FR 2-5 FR 2-6 FR 2 FR 155 FR 156 FR 166 FR 3 FR 168B FR 188 FR 4B FR 1810 FR 6
Shielded
FR 0 ZZ FR 1 ZZ FR 1-4 ZZ — FR 133 ZZS FR 1-5 ZZ FR 144 ZZ FR 2-5 ZZ FR 2-6 ZZS FR 2 ZZ FR 155 ZZS FR 156 ZZS FR 166 ZZ FR 3 ZZ FR 168 BZZ FR 188 ZZ FR 4B ZZ FR 1810 ZZ FR 6 ZZ
Abutment and Fillet Dimensions (mm)
Mass (g)
da
db
ra
min.
max.
max.
approx. Open Shielded
02.0 02.2 02.8 03.2 — 03.6 04.0 04.0 04.4 05.2 04.8 05.6 05.6 06.8 07.2 07.6 08.4 09.2 12.6
01.9 02.3 03.9 — 03.0 04.1 03.9 04.3 04.6 04.8 05.5 05.5 05.9 06.5 07.0 07.4 08.4 09.0 11.9
0.1 0.1 0.1 0.1 0.1 0.15 0.1 0.1 0.15 0.3 0.1 0.1 0.1 0.3 0.1 0.15 0.3 0.15 0.4
00.11 00.20 00.41 00.13 — 00.68 00.31 00.62 01.04 01.51 00.59 00.47 00.90 02.97 00.66 01.64 04.78 01.71 10.10
00.16 00.25 00.58 — 00.19 00.82 00.35 00.81 01.25 01.55 00.67 00.53 00.98 03.09 00.75 02.49 04.78 01.63 12.10
Remarks 1. When using bearings with a rotating outer ring, please contact NSK if they are shielded. 2. Bearings with double shields (ZZ, ZZS) are also available with single shields (Z, ZS).
B 44
B030-045E.indd 44-45
B 45
11/20/13 4:54:23 PM