“Do not loose time, choose Long Life!”
Comparative wear-out of the tips
Long Life
“Do not loose time, choose Long Life!” BEDNAR is dedicated to the importance of high quality of the wearable parts. The cost of wearable parts plays an important role throughout the entire life of the soil processing machine.
Soil test made in very abrasive soil conditions has proven up to 7 times higher lifetime of long life tips in comparison with standard tips. Give it a try – it’s worth it!
STANDARD TIPS
LONG LIFE TIPS
Higher level of resistency of tips and wings significantly lowers not only the cost of wear on parts but also the time required for exchange of working units (tips, wings…). New tips and wings Long Life significantly increase the lifetime of these parts and thus increase the effectivness of the machines use.
With new Long Life working tips and wings you will achieve quality, time and cost benefits: »» Significantly higher lifetime than traditional standard parts* »» Consistent working depth and equal quality of work
*4–7× higher lifetime based on type of the machine, working depth, width, type of soil, moisture, tractor power, ground speed and position of the tips and wings
»» Improved penetration, lower traction power requirement due to the permanently sharp cutting edges »» No need to adjust working width during the wear-out period »» Time and cost savings due to fewer worn parts »» Longer period of use during a season »» Lower costs per hectar. »» Optimal utilisation of tractor power »» Savings on storage space and transport costs
»» Wear in length and thickness of tips affect function of the tips
»» Minimal wear in length and reduced wear in thickness
»» Working depth of machine must to be readjusted according the wear of the tips
»» Consistently good penetration in soil profiles
»» Worse penetration in soil profiles in case of worn tips »» Insufficient quality of work
»» No readjustment of the working depth »» Constant high quality of work »» Much higher lifetime »» Much higher machine performance due possibility to use machine effectively
Comparison of tips / wings characteristics
Comparison of work quality
NEW STANDARD TIPS
WORN STANDARD TIPS
»» Flat working angle
»» Acute working angle
»» Permanently flat working angle
»» Soil profile is undercut
»» Soil is pushed (soil is not undercut as by new tips)
»» Soil is undercut
»» Soil is no longer kept in upper layers
»» Constant low traction resistance
»» Soil is kept to upper layers »» Low traction resistance for the tractor
»» Higher traction resistance »» Higher fuel consumption »» High level of strain on the machine (frames, bearing etc.) »» Reduction of working speed
STANDARD TIPS
LONG LIFE TIPS
»» Soil is kept in upper layers »» Reduction of fuel consumption »» Reduction of strain on the machine (frames, bearing etc.) »» Higher working performance
LONG LIFE TIPS
THE CHARACTERISTICS OF NEW AND WORN LONG LIFE TIPS
STAY CONSTANT! COMPARISON OF WINGS
»» Wear of tip lenght affects function
»» Minimal wear of tips length
»» Worse loosening of tips
»» Optimum loosening of tips
»» Worse mixing of tips
»» Optimum mixing of tips
»» Worse work in depth
»» Problem-free work in depth
»» Formation of uneven bottom
»» Flat bottom
»» Worse drainage
»» Optimum drainage
»» Worse penetration of weared tips
»» Constant quality of penetration »» Much higher machine performance due to machine working effectively
STANDARD WINGS
LONG LIFE WINGS
»» Wear in width affects the function of wings
»» Minimal wear in width of wings
»» Loss of functionality
»» Excellent undercutting of soil profiles
»» Worse undercutting of soil profiles »» Worse mixing »» Worse establishment of seedbed »» Worse weed control
»» Maintenance of functionality »» Excellent mixing »» Optimum seedbed estabilishment »» Effective weed management »» Much higher machine performance due machine working effectively
Versatile cultivators
Chisel ploughs
FENIX
TERRALAND New wear resistant Long Life tips and wings for versatile cultivators FENIX
New wear resistant Long Life tips for chisel ploughs TERRALAND
Screw holes for attaching the tips to a tine
Screw holes for attaching the tips to a tine
Wear resistant carbides on the tips
Reinforcement of bottom part of the tips
Wear resistant carbides on the tips
Reinforcement of bottom part of the tips
Wings with carbides
ORDER CODES:
ORDER CODES:
KM060334 – Tip Long Life 80 mm (1 pc) KM000854 – Screw (1 pc) KM000858 – Screw (1 pc) KM000855 – Nut (2 pcs)
KM060340 – Tip Long Life 40 mm (1 pc) KM000906 – Screw (1 pc) KM000854 – Screw (1 pc) KM000855 – Nut (2 pcs)
KM060316 – Wing Long Life L 185 mm (1 pc) KM060317 – Wing Long Life R 185 mm (1 pc) KM000890 – Screw (2 pcs) KM000296 – Nut (2 pcs)
T: +420 283 092 529 E:
[email protected] W: www.bednar-machinery.com
Product range
BEDNAR FMT s.r.o. Lohenická 607 190 17 Praha 9 - Vinoř Czech Republic
The technical data and illustrations are approximate. Reservations are made for any design changes.
TILLAGE Straw harrows STRIEGEL-PRO
Disc cultivators SWIFTERDISC
Disc cultivators ATLAS
TILLAGE Seedbed cultivators SWIFTER
Versatile cultivators FENIX
TILLAGE
INTER-ROW CULTIVATION
Trailed packers CUTTERPACK, PRESSPACK, GALAXY
Inter-row cultivator ROW-MASTER
SOWING AND FERTILISING Seed drills OMEGA
www.bednar-machinery.com
Fertliser hopper FERTI-BOX
Chisel ploughs TERRALAND
ROTARY CUTTERS Rotary cutters MULCHER
