SIMATIC Product Information 02.2009

CPU 414-4H, 417-4H

Deutsch Diese Produktinformation enthält wichtige Informationen zu den nachfolgend aufgeführten Produkten. Sie ist als separater Bestandteil aufzufassen und in Zweifelsfällen in der Verbindlichkeit anderen Aussagen in Handbüchern und Katalogen übergeordnet.

CPU

Bestellnummer

Firmware-Stand

CPU 414-4H

6ES7 414-4HJ00-0AB0

V3.1.5

CPU 417-4H

6ES7 417-4HL01-0AB0

V3.1.5

Der Einsatz der aktuellen Version von STEP7 oder der Engineering-Tools ist nur dann erforderlich, wenn die aktuelle CPU gegenüber dem letzten Firmwarestand neue Funktionen besitzt und Sie diese auch einsetzen wollen. Analog gilt beim Ersatz einer alten CPU durch eine CPU mit aktueller Firmware: Solange Sie keine Eigenschaften nutzen wollen, die über den Leistungsumfang der ausgetauschten CPU hinausgehen, können Sie bei der Projektierung in HWKonfig die CPU mit alter MLFB und altem Firmware-Stand benutzen. Die Technischen Daten der CPUs 414-4H und 417-4H finden Sie im Handbuch Automatisierungssysteme S7-400H, Hochverfügbare Systeme A5E00068168 ab Ausgabe 08. Dies hat die Bestellnummer 6ES7988-8HA10-8AA0 Copyright E Siemens AG 2009 Änderungen vorbehalten Subject to alteration A5E00073168-12

1

CPU 414-4H / CPU 417-4H

English This Product Information contains additional information about the following products. It is a separate component and should be considered more up-to-date than the information in the manuals and catalogs if uncertainties arise. CPU

Order Number

Firmware version

CPU 414-4H

6ES7 414-4HJ00-0AB0

V3.1.5

CPU 417-4H

6ES7 417-4HL01-0AB0

V3.1.5

The use of the current STEP 7 version or of the engineering tools is only then required, if, in contrast to the previous firmware version, the current CPU has new functions and you want to use them. Accordingly, when replacing an old CPU with a CPU of current firmware the following applies: As long as you do not want to use any properties which exceed the performance range of the exchanged CPU, you can use the CPU with the old order number and old firmware version when configuring in HW Config. You can find the technical specifications of the CPUs 414-4H and 417-4H in the Automation Systems S7-400, Fault-tolerant Systems manual A5E00068197 as ofedition 08. This has the order number 6ES7988-8HA10-8BA0.

2

A5E00073168-12

CPU 414-4H / CPU 417-4H

Deutsch

1.

Aufbau und Inbetriebnahme

Notwendige Versionen bzw. Bestellnummern wichtiger Systemkomponenten Systemkomponente

Notwendige Version bzw. Bestellnummer

STEP 7

ab V5 V5.2 2

H-Optionspaket

ab V5.2

Externer Master am PROFIBUS DP CP443 5 Extended CP443-5

Bestell-Nr. 6GK7443-5DX02-0XE0 ab Hardware-Stand 2 und ab Firmware-Version 3.2 Bestell-Nr. 6GK7443-5DX03-0XE0 ab Hardware-Stand 1 und ab Firmware-Version 5.0 Bestell-Nr. 6GK7443-5DX04-0XE0 ab Hardware-Stand 1 und ab Firmware-Version 6.0

Redundante DPSlave-Anschaltungen IM 153-2 und IM 153-2FO

IM 153-2: 6ES7 153-2AA02-0XB0 ab Erzeugnisstand 7 IM 153-2: 6ES7 153-2BA00-0XB0 ab Erzeugnisstand 1 IM 153-2: 6ES7 153-2BA01-0XB0 ab Erzeugnisstand 1 und Firmwarestand 4.0 IM 153-2: 6ES7 153-2BA02-0XB0 ab Erzeugnisstand 1 und Firmwarestand 5.0.9 IM 153-2FO: 6ES7 153-2AB01-0XB0 ab Erzeugnisstand 6 IM 153-2FO: 6ES7 153-2AB02-0XB0 ab Erzeugnisstand 1

DP/PA Koppler bzw. Y-Link IM 157

6ES7 157-0AA81-0XA0 ab Erzeugnisstand 1 und Firmwarestand 3.1 6ES7 157-0AA82-0XA0 ab Erzeugnisstand 1 und Firmwarestand 4.0 6ES7 157-0BA82-0XA0 ab Erzeugnisstand 1 und Firmwarestand 5.0.9

Kommunikationsbaugruppe CP443-1 (Industrial Ethernet, Ethernet TCP / ISO-Transport)

6GK7443-1EX10-0XE0 ab Hardwarestand 1 und Firmwarestand 2.1 (Empfohlen: Den derzeit aktuellen Firmwarestand verwenden) 6GK7443-1EX11-0XE0 ab Hardwarestand 1 und Firmwarestand 2.1 (Empfohlen: Den derzeit aktuellen Firmwarestand verwenden)

Kommunikationsbau6GK7443-5FX01-0XE0 ab Hardwarestand 2 und Firmwarestand gruppe CP443-5 Basic 3.2 (PROFIBUS; S7-Kommunikation) A5E00073168-12

3

CPU 414-4H / CPU 417-4H

Achtung: Bei den einzelnen Baugruppen können weitere Einschränkungen bestehen. Beachten Sie die Hinweise in den entsprechenden Produktionformationen und FAQs bzw. im SIMATIC NET Aktuell.

2.

Projektierung

Überwachungszeit von F-Baugruppen Falls Sie F-Baugruppen einsetzen, müssen Sie die Überwachungszeit jeder F-Baugruppe grö– ßer wählen als die Umschaltdauer des aktiven Kanals im H-System Eine Formel für die Obergrenze dieser Umschaltdauer finden Sie im Handbuch Automatisierungssysteme S7-400F und S7–400FH, Kapitel 7.4 “Überwachungszeiten”. Falls Sie diese Vorschrift nicht beachten, kann es bei der Umschaltung des aktiven Kanals zum Ausfall von F-Baugruppen kommen.

Projektierung von Baugruppen, die im Peripherie-Adressraum adressiert werden

Projektieren Sie eine Baugruppe, die im Peripherie-Adressraum adressiert wird, immer so, daß sie entweder komplett innerhalb oder komplett außerhalb des Prozessabbildes liegt. Andernfalls ist die Konsistenz nicht mehr gewährleistet und es können verfälschte Daten entstehen.

3.

Programmierung

Peripheriezugriffsfehler innerhalb DP Treten Zugriffsfehler auf vorhandene Baugruppen ohne direkt ersichtlichen Grund (fehlerfreie Station) auf, so kann die Ursache eine zu kurz eingestellte Parametrierüberwachungszeit sein (siehe auch Angaben zur Parametrierüberwachungszeit in Kap. 2 Projektierung).

Peripheriezugriff über Wort- und Doppelwortbefehle Sind bei einem Peripheriezugriff über Wort- und Doppelwortbefehle zwar das erste Byte bzw. die ersten ein bis drei Bytes vorhanden, der Rest des adressierten Bereichs jedoch nicht, so wird in den Akku “0” geladen. Beispiel: In der S7-400H ist die Peripherie mit der Adresse 8 und 9 vorhanden; die Adressen 10 und 11 sind nicht benutzt. Der Zugriff L ED 8 führt dazu, daß in den Akku der Wert W#16#00000000 geladen wird.

Einsatz der SFC49 “LGC_GADR” Sie betreiben ein Automatisierungssystem S7-400H im redundanten Betrieb. Falls Sie beim Aufruf der SFC49 im Parameter LADDR die logische Adresse einer Baugruppe eines geschalteten DP-Slaves angeben, wird im high byte des Parameters RACK die DP-Mastersystem-ID des aktiven Kanals geliefert. Falls kein aktiver Kanal existiert, wird die DP-Mastersystem-ID des zugehörigen DP-Mastersystems der Master-CPU ausgegeben.

4

A5E00073168-12

CPU 414-4H / CPU 417-4H

Aufruf der SFC51 “RDSYSST” mit SZL_ID=W#16#0232 und INDEX=W#16#0004 Entgegen den Angaben im Referenzhandbuch S7-300/400 Systemsoftware für S7-300/400 System- und Standardfunktionen werden bei einem H-System nicht nur im Betriebszustand RUN-REDUNDANT, sondern auch im Betriebszustand Solobetrieb sowie im Einzelbetrieb zwei Datensätze zurückgeliefert. Davon ist nur derjenige gültig, der im Byte 0 des Wortes “Index” einen von Null verschiedenen Wert hat.

Aufruf der SFC51 “RDSYSST” mit SZL_ID=W#16#xy91 Bei den CPUs 414-4H und 417-4H sind die Datensätze zu folgenden SZL-Teillisten mittels SFC51 “RDSYSST” nicht auslesbar: SZL_ID=W#16#0091, W#16#0191, W#16#0291, W#16#0391, W#16#0991, W#16#0E91

Einsatz der SFC 23 “DEL_DB”

Die Bedeutung des Werts W#16#80B4 des Parameters RET_VAL bei der SFC 23 ”DEL_DB” wurde geändert. Bisher: Der DB konnte nicht gelöscht werden, da er ein Baustein aus der F–Bibliothek ist. Jetzt: Der DB konnte nicht gelöscht werden. Mögliche Ursachen: Er ist ein Baustein aus der F–Bibliothek. Er ist ein Instanz–DB eines Bausteins der S7–Kommunikation. (nur bei S7-400)

Einsatz der SFC 31 und 33 – 36 “Alarm und Notify” und der SFB 8, 9 und 12 und 13 “USEND/URCV und BSEND/BRCV”

Bei den Alarm– und Notify–Bausteinen (SFB 31 und 33 – 36) und bei den Sende–/Empfangsbausteinen USEND/URCV (SFB 8, 9) und BSEND/BRCV (SFB 12, 13) können Sie jeweils eine EV_ID bzw. R_ID vergeben. Achten Sie unbedingt darauf, daß jede EV_ID bzw. R_ID in Ihrem Anwenderprogramm nur einmal verwendet wird. Werten Sie unbedingt die Parameter Error und Status aus. Error = 1 und Status = 18 signalisieren Ihnen, daß ein Fehler vorliegt und eine EV–ID bzw. R_ID doppelt vergeben wurde. Doppelt vergebene EV_ID bzw. R_ID verhindern eine korrekte Bearbeitung Ihres Programms.

Einsatz der SFC 90 ”H_CTRL”

Ergänzend zu den Angaben in der Online–Hilfe und im zugehörigen elektronischen Handbuch gilt: Falls Sie mit der SFC 90 ”H_CTRL” das Ankoppeln oder Aufdaten in der Master–CPU oder eine oder mehrere Testkomponenten des zyklischen Selbsttests gesperrt haben, dann gilt diese Sperre so lange, bis Sie diese mit der SFC 90 ”H_CTRL” wieder aufheben oder das H– System in den Systemzustand Stop geht.

A5E00073168-12

5

CPU 414-4H / CPU 417-4H

4.

Allgemeine Hinweise

Einsatz in fehlersicheren Systemen Die folgenden Zentralbaugruppen dürfen Sie in den fehlersicheren Systemen S7-400F und S7-400FH einsetzen:

S

CPU 414-4H mit der Bestellnummer 6ES7 414-4HJ00-0AB0, Erzeugnisstand 01, ab Firmware-Stand V3.1.0

S

CPU 417-4H mit der Bestellnummer 6ES7 417-4HL01-0AB0, Erzeugnisstand 01, ab Firmware-Stand V3.1.0

Hochverfügbare S7-Verbindungen Bei laufenden Kommunikationsaufträgen über hochverfügbare S7-Verbindungen führen Unterbrechungen einer Teilverbindung zu Laufzeitverlängerungen.

Einsatz der SFBs 52 bis 54 bei Verwendung einer externen DP-Anschaltung

Falls Sie die SFBs 52 “RDREC”, 53 “WRREC” oder 54 “RALRM” einsetzen und dabei über eine externe DP-Anschaltung auf DP-Slaves zugreifen wollen, müssen Sie folgendes beachten: Die genannten SFBs haben nur dann die in der Online-Hilfe und im elektronischen Handbuch beschriebene Funktionalität, wenn Sie als externe DP-Anschaltung einen CP443-5 ext. mit der Bestellnummer 6GK7 443-5DX03-0XE0 ab Firmwarestand V4.0.0 einsetzen.

Forcen von Variablen

Das Forcen von Variablen, die im Peripherie- oder Prozeßabbildbereich eines DP-Normslaves liegen und zu einem Konsistenzbereich gehören, ist nicht erlaubt. Das Anwenderprogramm kann diese Variablen nämlich trotz Forceauftrag überschreiben.

Besonderheiten bei der SFC 13 ”DPNRM_DG”

Tritt während der Bearbeitung der SFC 13 ein Fehler auf, so kann es vorkommen, daß das Busy-Bit nicht auf “0” gesetzt wird.Prüfen Sie daher nach jeder Bearbeitung der SFC 13 den Parameter RET_VAL ab.

Ändern der Zuordnung eines Teilprozeßabbildes

Sie können in einem H-System im laufenden Betrieb die Zuordnung einer Baugruppe zu einem Teilprozeßabbild ändern, indem Sie die Baugruppe bei einer Anlagenänderung im laufenden Betrieb zunächst entfernen und danach in einem zweiten Schritt mit der neuen Zuordnung wieder in die Projektierung aufnehmen.

Laden einer Projektierung

Wenn beim Laden einer Projektierung mit STEP 7 folgende Fehlermeldung auftritt, laden Sie die Projektierung erneut: ”(D2AB) Eine Änderung der dynamischen Mengengerüste ist aktiv. Das Anwenderprogramm wird neu ausgewertet.” ”SDB1xxx kann nicht geladen werden” ”Systemdaten können nicht auf die Baugruppe ... geladen werden”

6

A5E00073168-12

CPU 414-4H / CPU 417-4H

Baugruppenträgernummer ändern

Wenn Sie die Baugruppenträgernummer an den Sync-Modulen ändern (siehe Handbuch Automatisierungssystem S7-400H), leuchten danach die beiden LEDs IFM 1 und IFM 2 weiter. Diese erlöschen nach nochmaligem manuellem Urlöschen bzw. Netz aus/Netz ein.

Erzeugen bausteinbezogener Meldungen

Entgegen den Angaben in der Online–Hilfe und im zugehörigen elektronischen Handbuch gilt für den Arbeitsspeicherbedarf der SFBs zur Erzeugung bausteinbezogener Meldungen: Die SFBs zur Erzeugung bausteinbezogener Meldungen benötigen zu ihrer reibungslosen Funktion einen i.a. begleitwertabhängigen Kommunikationsdatenpuffer im Arbeitsspeicher der CPU (Codebereich). Die Größe des belegten Speichers entnehmen Sie der folgenden Tabelle. Bausteintyp

Benötigter Speicherbedarf im Arbeitsspeicher der CPU in Byte

NOTIFY, NOTIFY_8P, ALARM, ALARM_8P

200 + 2 * Länge der beim Erstaufruf an SD_1,...SD_10 angegebenen Begleitwerte

ALARM_8

100

AR_SEND

54

A5E00073168-12

7

CPU 414-4H / CPU 417-4H

5.

Geänderte Fehlerreaktion

Hardware-Fehler mit einseitigem OB 121-Aufruf, Quersummenfehler Bei Hardware-Fehlern mit einseitigem OB 121-Aufruf und bei Quersummenfehlern verhält sich eine CPU 41x-4H beim ersten Auftreten so, wie im Handbuch “Automatisierungssystem S7-400, Hochverfügbare Systeme” in Kapitel 5 beschrieben. Die Reaktion der CPU auf das zweite Auftreten eines solchen Fehlers wurde geändert und ist in nachfolgender Tabelle für die verschiedenen Betriebsarten einer CPU 41x-4H dargestellt. Fehler

CPU im Solobetrieb

CPU im Einzelbetrieb

CPU im Redundanzbetrieb

HW-Fehler mit einseitigem OB 121-Aufruf

OB 121 wird ausgeführt OB 121 wird ausgeführt Die fehlerhafte CPU geht in den Betriebszustand FEHLERSUCHE. Das H-System geht in den Solobetrieb.

Quersummenfehler

Treten zwei Fehler innerhalb zweier aufeinanderfolgender Testzyklen auf, geht die CPU in den Zustand DEFEKT. (Die Länge des Testzyklus projektieren Sie in HW-Config)

Treten zwei Fehler innerhalb zweier aufeinanderfolgender Testzyklen auf, geht die CPU in den Zustand DEFEKT. (Die Länge des Testzyklus projektieren Sie in HW-Config)

Tritt ein zweiter Fehler noch innerhalb des Fehlersuchbetriebes auf, der vom ersten Fehler ausgelöst wurde, geht die CPU in den Zustand DEFEKT

Hinweis: Tritt ein zweiter Quersummenfehler im Solobetrieb bzw. Einzelbetrieb nach Ablauf der doppelten Testzykluszeit auf, reagiert die CPU wie beim ersten Auftreten des Fehlers. Tritt ein zweiter Fehler (Hardware-Fehler mit einseitigem OB 121-Aufruf, Quersummenfehler) im Redundanzbetrieb nach Ablauf des Fehlersuchbetriebs auf, reagiert die CPU wie beim ersten Auftreten des Fehlers.

8

A5E00073168-12

CPU 414-4H / CPU 417-4H

English

1.

Configuration and Commissioning

Necessary Versions or Order Numbers of Important System Components System Component

Necessary Versions or Order Number

STEP 7

as of V5 V5.2 2

H-optional package

as of V5.2

External master on PROFIBUS DP CP443 5 extended CP443-5

Order No. 6GK7443-5DX02-0XE0 as of hardware version 2 and as of firmware version 3.2 Order No. 6GK7443-5DX03-0XE0 as of hardware version 1 and as of firmware version 5.0 Order No. 6GK7443-5DX04-0XE0 as of hardware version 1 and as of firmware version 6.0

Redundant DP slave IM 153-2: 6ES7 153-2AA02-0XB0 as of version 7 interface module IM IM 153-2: 6ES7 153-2BA00-0XB0 as of version 1 153-2 and IM 153-2FO IM 153-2: 6ES7 153-2BA01-0XB0 as of version 1 and firmware version 4.0 IM 153-2: 6ES7 153-2BA02-0XB0 as of version 1 and firmware version 5.0.9 IM 153-2FO: 6ES7 153-2AB01-0XB0 as of version 6 IM 153-2FO: 6ES7 153-2AB02-0XB0 as of version 1 DP/PA Coupler or YLink IM 157

A5E00073168-12

6ES7 157-0AA81-0XA0 as of version 1 and firmware version 3.1 6ES7 157-0AA82-0XA0 as of version 1 and firmware version 4.0 6ES7 157-0BA82-0XA0 as of version 1 and firmware version 5.0.9

9

CPU 414-4H / CPU 417-4H

System Component

Necessary Versions or Order Number

Communication module CP443-1 (Industrial Ethernet, Ethernet TCP / ISO-Transport)

6GK7443-1EX10-0XE0 as of hardware version 1 and firmware version 2.1 (Recommended: Use the actual version)

Communication module CP443-5 Basic (PROFIBUS; S7 communication)

6GK7443-5FX01-0XE0 as of hardware version 2 and firmware version 3.2

6GK7443-1EX11-0XE0 as of hardware version 1 and firmware version 2.1 (Recommended: Use the actual version)

Caution: There may be further restrictions with the individual modules. Note the information in the individual product information and FAQs as well as in the SIMATIC NET news.

2.

Configuration

Monitoring Time of F Modules If you are using F modules, you have to select the monitoring time for each F module higher than the switch-over time of the active channel in the H system (You can find a formula for the upper limit of this switch-over time in the Programmable Controllers S7 F/FH Systems manual, Section 7.4 “Monitoring Times”.). If you do not observe these regulations, the F modules may fail when switching over the active channel.

Configuring Modules which are Addressed in the I/O Address Area

Always configure a module which is addressed in the I/O address area in such a way that it either lies completely within or completely outside of the process image. Otherwise the consistency is no longer guaranteed and falsified data may be output.

3.

Programming

I/O Access Errors Within DP If errors occur accessing existing modules without an obvious cause (error-free station), it might be because the parameter assignment monitoring time has been set too short (see also the information on the parameter assignment monitoring time in Section 2, Configuration).

I/O Access Using Word and Double Word Commands If, in the case of I/O access via word and double-word commands, the first byte or the first one to three bytes are present, but the rest of the addressed range is not, “0” is loaded in the accumulator.

10

A5E00073168-12

CPU 414-4H / CPU 417-4H

Example: The I/O is present In the S7-400H with the addresses 8 and 9; the addresses 10 and 11 are not used. The access LED 8 results in the value W#16#00000000 being loaded into the accumulator.

Using the SFC49 “LGC_GADR” You are operating an S7-400 programmable controller in redundant mode. If you enter a logic module address of a switched DP slave in the LADDR parameter when calling the SFC49, the DP master system ID of the active channel is output in the high byte of the RACK parameter. If no active channel exists, the DP master system ID of the associated DP master system of the master CPU is output.

Calling the SFC51 “RDSYSST” with SZL_ID=W#16#0232 and INDEX=W#16#0004 In contrast to the information in the Systemsoftware for S7-300 and S7-400, System and Standard Functions reference manual, an H system outputs two data records, not only in RUN-REDUNDANT operating mode, but also in solo mode and in separate operation. However, only the data record which has a value  0 in the byte 0 of the word “index” is valid.

Calling the SFC51 “RDSYSST” Using SZL_ID=W#16#xy91 For the CPUs 414-4H and 417-4H the data records for the following SSL partial lists cannot be read using SFC51 “RDSYSST”: SZL_ID=W#16#0091, W#16#0191, W#16#0291, W#16#0391, W#16#0991, W#16#0E91

Using SFC23 “DEL_DB”

The meaning of value the W#16#80B4 for the parameter RET_VAL has been changed for SFC 23 ”DEL_DB”. Previously: The DB could not be deleted because it was a block from the F library. Now: The DB could not be deleted. Possible causes: It is a block from the F library. It is an instance DB of S7 communication block. (only in S7-400)

Using SFC 31 and 33 – 36 “Alarm and Notify” and SFB 8, 9 and 12 and 13 “USEND/URCV and BSEND/BRCV”

You can assign EV_ID and R_ID respectively for the interrupt and notify blocks (SFB 31 and 33 – 36) and for the send /receive blocks USEND/URCV (SFB 8, 9) and BSEND/ BRCV (SFB 12, 13) Make sure each EV_ID or R_ID is used only once in your user program. It is absolutely necessary that you evaluate the Error and Status parameters. Error = 1 and Status = 18 notifies you that an error has occurred and that an EV–ID or a R_ID has been assigned twice. Double assignments of EV_ID or R_ID will prevent your program from being edited correctly.

A5E00073168-12

11

CPU 414-4H / CPU 417-4H

Using SFC 90 ”H_CTRL”

The following as applies as a supplement to the information the Online Help and the related electronic manuals: if you have disable link–up or update in the master CPU or one or more test components of the cyclical self–test SFC 90 “H_CTRL with, the disabling will remain until you reenable it with SFC 90 ”H_CTRL” or until the H–System goes to STOP.

4.

General Information

Use in Fail-Safe Systems You can use the following CPU modules in the S7-400F and S7-400FH fail-safe systems:

S

CPU 414-4H with the order number 6ES7 414-4HJ00-0AB0, version 01, as of firmware version V3.1.0

S

CPU 417-4H with the order number 6ES7 417-4HL01-0AB0, version 01, as of firmware version V3.1.0

Fault-Tolerant S7 Connections Interruptions of a partial connection result in a prolonging of the runtime for ongoing communication jobs via fault-tolerant S7 connections.

Using the SFBs 52 to 54 with an External DP Interface Module

If you are using the SFBs 52 “RDREC”, 53 “WRREC” or 54 “RALRM” with the intention to access DP slaves via an external DP interface module, observe the following: Only when you are using a CP443-5 ext. with the order number 6GK7 443-5DX03-0XE0 as of firmware version V4.0.0 as an external DP interface module, the specified SFBs have the functionality described in the online help and in the electronic manual.

Forcing Variables It is not permitted to force variables which lie in the I/O or process image range of a DP standard slave and belong to a consistency range, as the user program can overwrite these variables in spite of a force job.

Special features with SFC 13 ”DPNRM_DG”

If an error occurs while editing SFC 13, the Busy bit may not be set to “0”. Therefore, check the parameter RET_VAL each time you finish editing SFC 13.

Changing the Assignment to a Process Image Sections

During an operation you can change the assignment of a module to a process image section in H system by first removing the module when modifications are made to the plant during operation and then making new assignments in the configuration in a second step.

Downloading a Configuration

If the following error message is output while downloading a configuration with STEP 7, reload the configuration:

12

A5E00073168-12

CPU 414-4H / CPU 417-4H

”(D2AB) A modification of the dynamic frameworks is active. The user program will be reevaluated.” ”SDB1xxx cannot be downloaded” ”System data cannot be downloaded to the module ... ”

Modifying Rack Numbers

When you change the rack number on a sync module (see S7-400H Automation System manual), the two LEDs IFM 1 and IFM 2 will remain lit. They will go off after a manual memory reset or POWER OFF/POWER ON.

Creating Block–related Messages

Contrary to the information in the Online Help and in the related electronic manual, the following applies for SFBs memory requirement for creating block-related messages: For a smooth function, the SFBs for creating block-related messages require a communications data buffer dependent on an associated value in the CPU’s memory (code area). Refer to the table below for the size of the used memory. Block Type

Memory Requirement in the CPU’s Memory in Bytes

NOTIFY, NOTIFY_8P, ALARM, ALARM_8P

200 + 2 * Size of the specified associated value during the first call to SD_1,...SD_10

ALARM_8

100

AR_SEND

54

5.

Modified Error Response

Hardware fault with one-way OB 121 call, Checksum error In the event of hardware faults with a one-way OB 121 call and of checksum errors, a CPU 41x-4HOB behaves as described in chapter 5 of the manual “Automation System S7-400, Fault–tolerant system” when called for the first time. The CPU response to the second occurence of such error has been changed. This changed is described for the different CPU modes of a CPU 41x-4H in the table below.

A5E00073168-12

13

CPU 414-4H / CPU 417-4H

Errors

CPU in single mode

CPU in single operation

CPU in redundant mode

Hardware fault with a one-way OB 121 call

OB 121 is being executed

OB 121 being executed The faulty CPU goes to TROUBLESHOOTING mode. The H system goes to single mode.

Checksum error

If two faults occur in two successive test cycles, the CPU goes to DEFECTIVE mode. (You can configure the length of the test cycle in HW Config)

If two faults occur in two successive test cycles, the CPU goes to DEFECTIVE mode. (You can configure the length of the test cycle in HW Config)

If a second fault, triggered by the first fault, occurs in the troubleshooting mode, the CPU goes to DEFECTIVE state.

Note: If a second checksum error occurs in the single mode or single operation after the double test cycle period, the CPU will respond as it did during the first error occurence. If a second fault (hardware fault with a one–way OB 121 call, checksum error) occurs in the redundant mode after the troubleshooting procedure, the CPU will respond as it did during the first fault occurence.

14

A5E00073168-12