Hydraulic Swing Clamp Mode l Mode l Mode l Mode l

LHA LHC LHS LHW

M o de l M o de l M o de l M o de l

L T/ L G TL A - 2 TL A - 1 TL B - 2

High Rigidity・Long Life・High Accuracy High Speed・High Rigidity・Swing Completion Position Repeatability ±0.5°(±0.75°only for LHS)

Action Description

Before Swing

The lever descends as it swings.

After swing completion,

Action completed

(Released State)

(For LHS, the lever swings parallel.)

it descends vertically.

(Clamped State)

Application Examples

Machining

Cleaning

285

For the applications which require clamp position repeatability

Press Fitting

Deburring

Swing Clamp Digest

New Products

High-Power Series Pneumatic Series

Compact Swing Clamp M o de l

Hydraulic Series

L HC

Valve / Coupler Hydraulic Unit

Compact swing clamps for small footprint fixtures

Manual Operation Accessories

designed with minimum required stroke.

Cautions / Others

Hole Clamp SFA

Many Varieties For General Purpose

SFC Swing Clamp L HA L HC L HS

33 mm

46.5 mm

L HW

Compact < Comparison Model >

< New Model >

LHA0400-C□ Lock Stroke：8mm

LHC0400-C□ Lock Stroke：6mm

Compact body with minimum required lock stroke for specific applications and limited spaces.

L T /L G TLA-2 T L B- 2 TLA-1 Link Clamp LK A LK C LK W LM/LJ T MA - 2 T MA - 1

Air Sensing Swing Clamp M o de l

Work Support

L HW

LD LC T NC

Clamp-unclamp confirmation with built-in air catch sensor

TC

for smaller footprint fixtures.

Air Sensing Lift Cylinder

Unclamp Confirmation Valve Clamp Confirmation Valve

LLW Compact Cylinder LL LLR LLU DP DR DS

79.5 mm For Action Confirmation

DT

46.5 mm

Block Cylinder

Same Size

33 mm ＜ Comparison Models ＞ LHA0400-C□M

LHA0400-C□ No Action Confirmation

DBA DBC

Compact

Control Valve

＜ New Model ＞ LHW0400-C□E

BZL BZT BZX/JZG Pallet Clamp VS VT

High-Power Swing Clamp M o de l

Expansion Locating Pin

Hydraulic Double Action

L HE

2 sizes smaller with equivalent clamping force. Mechanical lock and hydraulic pressure allow for strong clamping and holding force. Refer to P. 13 for further information.

VL VM VJ VK Pull Stud Clamp FP FQ Customized Spring Cylinder DW A /DW B

286

Swing Clamp

Low Pressure Model MAX. 7MPa Mode l

Classification

Action Confirmation Option

Double End Rod Option for Dog

Able to Install Dog

Air Sensing Manifold Option Air Sensing Piping Option

Able to Install Air Sensor

M ode l

LH C

→ P.319

M ode l

LH S

→ P.331

Double Action Compact

Double Action Parallel Swing Action

1. 5∼7M Pa

1. 5∼7M Pa

1. 5∼7M Pa

External Dimensions

→ P. 297

External Dimensions

→ P. 299

−

★

External Dimensions

→ P. 301

−

★

External Dimensions

→ P. 303

−

★

−

−

External Dimensions

−

Built-in Sensing Valve Model

→ P. 327

External Dimensions

→ P.3 3 9

Quick Change Lever Option

External Dimensions

→ P. 305

★

External Dimensions

→ P.3 4 1

Balance Lever Option

External Dimensions

→ P. 307

★

External Dimensions

→ P.3 4 3

External Dimensions

→ P. 309

−

External Dimensions

→ P. 313

★

Long Stroke Option

Long

Swing Angle Selectable Option Accessories

→ P.289

Double Action

Operating Pressure Range Standard Model

LH A

30° 45° 60°

LZH-T、LZH-F、LZH-B

Lever

LZY-MD

Speed Control Valve Plug

BZL、BZX、JZG

External Dimensions

LZH-T

→ P.3 4 5

LZH-T、LZH-F、LZH-B

→ P. 318

Manifold Block

★

→ P. 330

→ P.3 4 8 → P .1 0 2 5 → P.7 2 7

※ Please contact us for detail dimension at ★ part.

High Pressure Model MAX. 35MPa Model

Operating Pressure Range

7∼35M Pa

Standard Model

Option

Balance Lever Option

Swing Angle

Accessories

Selectable Option Lever Speed Control Valve Plug Ｇ-Thread Fitting 287

→ P.387

Double Action Top Flange

Classification

Long Stroke Option

TLA-2

Long

30° 45° 60°

Model

TLB-2

→ P.413

Double Action Bottom Flange 7∼35M Pa

Model

TLA-1

Single Action (Spring Release) Top Flange 7∼35M Pa

External Dimensions

→ P. 395

External Dimensions

→ P. 421

External Dimensions

→ P. 399

External Dimensions

→ P. 423

−

External Dimensions

→ P. 403

External Dimensions

→ P. 425

−

External Dimensions

→ P. 407

External Dimensions

→ P. 427

−

TLZ-L2、TLZ-LB → P. 412

TLZ-L2、TLZ-LB → P. 429

BZT、JZG Ｇ-Thread Fitting (Made by Ihara Science)

→ P.431

External Dimensions

→ P.4 3 9

TLZ-L2、TLZ-LB → P.4 4 3

→ P.7 2 7

→ P.1 0 3 9

Swing Clamp Digest

High-Power Series Pneumatic Series

Low Pressure Model

Hydraulic Series

MAX. 7MPa Model

Classification Operating Pressure Range

LH W

1. 5∼7M Pa

2. 5∼7M Pa

−

Action Confirmation Option

External Dimensions

−

SFC

Able to Install Air Sensor

−

−

−

−

External Dimensions

Swing Clamp L HA L HC L HS L HW

−

→ P. 359

L T /L G TLA-2

External Dimensions

→ P. 377

Balance Lever Option

★

External Dimensions

→ P. 379

T L B- 2 TLA-1 Link Clamp LK A

Long

−

30° 45° 60°

LK C

−

★

External Dimensions

LK W

→ P. 381

LM/LJ T MA - 2 T MA - 1

LZH-T → P. 366

−

Manifold Block Speed Control Valve Plug

Cautions / Others

SFA

★

Lever

Manual Operation Accessories

→ P. 375

Quick Change Lever Option

Long Stroke Option

Valve / Coupler Hydraulic Unit

Hole Clamp

−

Able to Install Dog

Built-in Sensing Valve Model

Swing Angle Selectable Option Accessories

LT/LG → P.367

Single Action (Spring Release)

Air Sensing Manifold Option Air Sensing Piping Option

Model

Double Action Built-in Sensing Valve

Standard Model Double End Rod Option for Dog

→ P.349

LZ-LE1、LZ-LE2 LZH-F、LZH-B → P. 384 LZ-MS

BZL、BZX、JZG

→ P. 1026

Work Support LD LC T NC TC

→ P. 727

Air Sensing Lift Cylinder LLW Compact Cylinder LL LLR LLU DP DR DS DT Block Cylinder DBA DBC Control Valve BZL BZT BZX/JZG Pallet Clamp VS VT

High-Power Swing Clamp M o de l

Expansion Locating Pin

Hydraulic Double Action

LH E

2 sizes smaller with equivalent clamping force. Mechanical lock and hydraulic pressure allow for strong clamping and holding force. Refer to P. 13 for further information.

VL VM VJ VK Pull Stud Clamp FP FQ Customized Spring Cylinder DW A /DW B

288

Double Action Compact Swing Clamp

m od e l

PAT.

Hydraulic Double Action Compact Swing Clamp Model

LHC

Low Pressure (1.5∼7MPa) High Speed・Compact

Index Hydraulic Swing Clamp Digest

P.285

Cross Section

P.320

Action Description

P.320

Model No. Indication

P.321

Specifications

P.322

Performance Curve Clamping Force Curve

P.323

Allowable Swing Time Graph

P.325

External Dimensions ・ Standard Model (LHC)

P.327

Lever Design Dimensions

P.329

Accessories ・Material Swing Lever for LHC

P.330

・Speed Control Valve・Plug (Common Items of Other Models)

P.727

・Manifold Block (Common Items of Other Models)

P.1025

Cautions ・ Notes for Hydraulic Swing Clamps

P.445

・ Cautions (Common)

P.1043

・Installation Notes ・Hydraulic Fluid List ・Notes on Hydraulic Cylinder Speed Control Circuit ・Notes on Handling ・Maintenance/Inspection ・Warranty

319

LHC

Swing Clamp Digest P.285

Index

Cross Section Model No. Indication Performance External Action Description Specifications Curve Dimensions

Lever Design Dimensions

Cross Section

Accessories

Cautions P.445

High-Power Series

Taper Sleeve

Pneumatic Series

Swing Lever

Dust Seal

Hydraulic Series Valve / Coupler Hydraulic Unit

Excellent Coolant Resistance

Manual Operation Accessories

BZL Speed Control Valve

Piston Rod

(Sold Separately)

Cautions / Others

Hole Clamp SFA SFC Swing Clamp LHA L HC LHS

Compact

LHW LT /LG T LA - 2 T LB- 2 T LA - 1 Link Clamp LK A LK C

Compact

LK W LM/LJ

The dimension below the flange is shortened to enable smaller footprint fixtures. The compact body enables the internal fitting to limit interference and makes

Compact, easy to fit, and no interference

fixture designing more engineer friendly.

T MA - 2 T MA - 1 Work Support LD

Able to Use Longer Levers

LC

The long guide ratio allows for longer clamping levers by supporting the rod.

High Speed

T NC TC

The guide is located between the flange and at the edge of the rod.

Excellent Coolant Resistance Our exclusive dust seal is designed to protect against high pressure coolant.

Air Sensing Lift Cylinder LLW

Ability to use longer levers

Compact Cylinder LL

It also has high durability against chlorine-based coolant by using a sealing

LLR

material with excellent chemical resistance.

LLU

High Speed and High Endurance with Rotation Mechanism

Cam Shaft （Piston Rod)

Lead Groove

Outer Race

The resistance created by the swing action is minimized by having the outer race rotates in accordance with the steel ball movement.

DP DR DS DT Block Cylinder DBA

High endurance is achieved by enlarging rod diameter which decreases

DBC

torque and by using bigger steel balls and making the lead groove.

Steel Ball

(Position repeatability for swing is within ±0.5° .)

Control Valve

Ball Guide Part

Able to Attach Speed Control Valve Directly

BZL BZT BZX/JZG

When fitting the gasket (-C option), it is able to attach the speed control valve Pallet Clamp

with air venting function. (Speed control valve is sold separately.)

VS VT

Action Description

Expansion Locating Pin VL VM VJ VK Pull Stud Clamp FP FQ

Before swing (Released State)

The lever descends as it swings.

After swing completion,

Action completed

it descends vertically.

(Clamped State)

Customized Spring Cylinder DW A /DW B

320

Double Action Compact Swing Clamp

m od e l

LHC

Model No. Indication

LH C 048 0 - C R 1

2

3

4

1 Body Size 036： φD=36mm 040： φD=40mm 048： φD=48mm 055： φD=55mm

φD

065： φD=65mm

※ Outer diameter (φD) of the cylinder.

2 Design No. 0 ： Revision Number

3 Piping Method C ： Gasket Option (With G Thread Plug)

With G Thread Plug Able to attach the speed control valve ※ Speed control valve (BZL) is sold separately. Please refer to P.727.

4 Swing Direction when Clamping

R

R ： Clockwise L ： Counter-Clockwise

321

Swing Direction when Clamping

L Swing Direction when Clamping

Swing Clamp Digest P.285

Cross Section Model No. Indication Performance External Action Description Specifications Curve Dimensions

Index

Lever Design Dimensions

Accessories

Cautions P.445

High-Power Series

Specifications Model No. Cylinder Area for Locking

cm2

Clamping Force ※1

kN F =

(Calculation Formula)

LHC0360-C□

LHC0400-C□

LHC0480-C□

LHC0550-C□

LHC0650-C□

3.54

5.00

6.95

10.3

13.4

P 2.8233+0.0173×L

F=

P 1.9988+0.0103×L

F=

P 1.4386+0.0072×L

F=

P 0.9712+0.0039×L

F=

P 0.7485+0.0027×L

Cylinder Inner Diameter

mm

φ26

φ31

φ37

φ44

φ51

Rod Diameter

mm

φ15

φ18

φ22

φ25

φ30

4.1

6.3

9.4

14.9

21.4 32.7

Cylinder Capacity Lock

6.1

9.4

14.5

22.0

Full Stroke

mm

11.5

12.5

13.5

14.5

16

Swing Stroke (90°)

mm

5.5

6.5

7.5

8.5

10

Vertical Stroke

mm

6

6

6

6

6

cm3

Release

90°±3°

Swing Angle Accuracy Max. Operating Pressure MPa

1.5

MPa

10.5

Operating Temperature

℃

Notes

Cautions / Others

Hole Clamp

Swing Clamp LHA L HC LHS

General Hydraulic Oil Equivalent to ISO-VG-32 kg

Manual Operation Accessories

SFC

0∼70

Usable Fluid Mass ※3

Valve / Coupler Hydraulic Unit

7.0

Min. Operating Pressure ※2 MPa Withstanding Pressure

Hydraulic Series

SFA

±0.5°

Swing Completion Position Repeatability

Pneumatic Series

0.6

0.8

※1. F：Clamping Force (kN), P：Supply Hydraulic Pressure (MPa),

1.2

1.8

※3. Mass of single swing clamp including taper sleeve and nut.

LT /LG T LA - 2

L

T LB- 2

L：Distance between the piston center and the clamping point (mm). ※2. Minimum pressure to operate the clamp without load.

LHW

2.4

T LA - 1

F

1. Please refer to P.445 and P.446 for cautions and tightening torque when mounting the cylinder body and swing lever.

Link Clamp LK A LK C LK W LM/LJ T MA - 2 T MA - 1 Work Support LD LC T NC TC Air Sensing Lift Cylinder LLW Compact Cylinder LL LLR LLU DP DR DS DT Block Cylinder DBA DBC Control Valve BZL BZT BZX/JZG Pallet Clamp VS VT Expansion Locating Pin VL VM VJ VK Pull Stud Clamp FP FQ Customized Spring Cylinder DW A /DW B

322

Double Action Compact Swing Clamp

m od e l

LHC

Clamping Force Curve Applicable Model

L：Lever Length (mm)

L HC

0 -

C

R L

1 Body Size

F ：Clamping Force (kN) s

P：Hydraulic Pressure (MPa)

(Example) When using LHC0480, Supply Hydraulic Pressure 5.0MPa, Lever Length L=50mm, the clamping force is about 2.8kN. Notes 1. Tables and graphs shown are the relationships between the clamping force (kN) and supply hydraulic pressure (MPa). 2. Cylinder output (when L=0) cannot be calculated from the calculation formula of clamping force. 3. There may be no lever swing action with large inertia depending on supply hydraulic pressure or lever mounting position. 4. The clamping force is shown with lever in the locked position. 5. The clamping force varies depending on the lever length. Set the supply hydraulic pressure suitable to the lever length. 6. Using in the non-usable range may damage the clamp and lead to fluid leakage. 7. The tables and graphs are only for reference. The exact results should be calculated based on the clamping force calculation formula. ※1. F: Clamping Force (kN), P:Supply Hydraulic Pressure (MPa), L: Lever Length (mm)

L=60 3.7 3.5 3.2 2.9 2.7 2.4 2.1 1.9 1.6 1.3 1.1 0.8 7.0

Clamping Force (kN) Non-Usable Range(■) Max. Lever Length Lever Length L(mm) (L) L=80 L=100 L=120 L=140 L=160 L=200 (mm) 3.5 3.2 105 3.2 3.0 118 3.0 2.8 2.6 134 2.7 2.5 2.4 2.2 156 2.5 2.3 2.2 2.0 1.9 186 2.2 2.1 2.0 1.8 1.7 1.6 230 2.0 1.9 1.7 1.6 1.5 1.4 230 1.7 1.6 1.5 1.4 1.3 1.2 230 1.5 1.4 1.3 1.2 1.2 1.0 230 1.2 1.2 1.1 1.0 1.0 0.9 230 1.0 0.9 0.9 0.8 0.8 0.7 230 0.7 0.7 0.7 0.6 0.6 0.5 230 7.0 7.0 6.4 5.8 5.4 4.8

L=30(s=10) L=50(s=30) L=100(s=80)

1.5

L=140(s=120) 1 Non-Usable Range (■) 0.5

0

Clamping Force (kN)

0

1 2 3 4 5 6 Supply Hydraulic Pressure (MPa)

7

3.5

Cylinder Force

3

L=40(s=17.5) L=80(s=57.5)

2.5

L=100(s=77.5)

2

L=150(s=127.5)

1.5 1

Non-Usable Range (■)

0.5 0

0

1 2 3 4 5 6 Supply Hydraulic Pressure (MPa)

7

5

Clamping Force Calculation Formula ※1 (kN) F = P ／ ( 1.4386 + 0.0072×L)

Hydraulic Cylinder Force Pressure (kN) (MPa) L=50 7 4.9 3.9 6.5 4.5 3.6 6 4.2 3.3 5.5 3.8 3.1 5 3.5 2.8 4.5 3.1 2.5 4 2.8 2.2 3.5 2.4 1.9 3 2.1 1.7 2.5 1.7 1.4 2 1.4 1.1 1.5 1.0 0.8 Max. Operating Pressure (MPa) 7.0

323

L=50 2.8 2.6 2.4 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 7.0

Clamping Force (kN) Non-Usable Range(■) Max. Lever Length Lever Length L(mm) (L) L=60 L=70 L=80 L=100 L=120 L=150 (mm) 2.7 2.6 2.5 2.3 100 2.5 2.4 2.3 2.1 112 2.3 2.2 2.1 2.0 1.9 128 2.1 2.0 1.9 1.8 1.7 148 1.9 1.8 1.8 1.7 1.5 1.4 176 1.7 1.7 1.6 1.5 1.4 1.3 210 1.5 1.5 1.4 1.3 1.2 1.1 210 1.3 1.3 1.2 1.2 1.1 1.0 210 1.1 1.1 1.1 1.0 0.9 0.8 210 1.0 0.9 0.9 0.8 0.8 0.7 210 0.8 0.7 0.7 0.7 0.6 0.6 210 0.6 0.6 0.5 0.5 0.5 0.4 210 7.0 7.0 7.0 7.0 6.2 5.4

Cylinder Force

2

Clamping Force Calculation Formula ※1 (kN) F = P ／ ( 1.9988 + 0.0103×L)

Hydraulic Cylinder Force Pressure (kN) (MPa) L=40 7 3.5 2.9 6.5 3.3 2.7 6 3.0 2.5 5.5 2.8 2.3 5 2.5 2.1 4.5 2.3 1.9 4 2.0 1.7 3.5 1.8 1.5 3 1.5 1.2 2.5 1.3 1.0 2 1.0 0.8 1.5 0.8 0.6 Max. Operating Pressure (MPa) 7.0

LHC0480

L=40 2.0 1.8 1.7 1.6 1.4 1.3 1.1 1.0 0.9 0.7 0.6 0.4 7.0

Clamping Force (kN) Non-Usable Range(■) Max. Lever Length Lever Length L(mm) (L) L=50 L=60 L=80 L=100 L=120 L=140 (mm) 1.9 1.8 1.7 95 1.8 1.7 1.5 1.4 107 1.6 1.6 1.4 1.3 1.2 122 1.5 1.4 1.3 1.2 1.1 1.0 143 1.4 1.3 1.2 1.1 1.0 1.0 150 1.2 1.2 1.1 1.0 0.9 0.9 150 1.1 1.0 1.0 0.9 0.8 0.8 150 0.9 0.9 0.8 0.8 0.7 0.7 150 0.8 0.8 0.7 0.7 0.6 0.6 150 0.7 0.6 0.6 0.5 0.5 0.5 150 0.5 0.5 0.5 0.4 0.4 0.4 150 0.4 0.4 0.4 0.3 0.3 0.3 150 7.0 7.0 7.0 6.7 6.0 5.5

Clamping Force (kN)

Hydraulic Cylinder Force Pressure (kN) (MPa) L=30 7 2.5 2.1 6.5 2.3 1.9 6 2.1 1.8 5.5 2.0 1.6 5 1.8 1.5 4.5 1.6 1.3 4 1.4 1.2 3.5 1.2 1.0 3 1.1 0.9 2.5 0.9 0.7 2 0.7 0.6 1.5 0.5 0.4 Max. Operating Pressure (MPa) 7.0

LHC0400

2.5

Clamping Force Calculation Formula ※1 (kN) F = P ／ ( 2.8233 + 0.0173×L)

Cylinder Force

4 Clamping Force (kN)

LHC0360

L=50(s=24.5) L=100(s=74.5)

3

L=150(s=124.5) L=200(s=174.5)

2 Non-Usable Range (■) 1

0

0

1 2 3 4 5 6 Supply Hydraulic Pressure (MPa)

7

Swing Clamp Digest P.285

Index

Cross Section Model No. Indication Performance External Action Description Specifications Curve Dimensions

Lever Design Dimensions

Accessories

Cautions P.445

High-Power Series Pneumatic Series

Hydraulic Series Valve / Coupler Hydraulic Unit Manual Operation Accessories Cautions / Others

Hole Clamp SFA SFC Swing Clamp LHA L HC LHS LHW LT /LG T LA - 2 T LB- 2 T LA - 1

LHC0650

L=60 5.8 5.4 5.0 4.6 4.1 3.7 3.3 2.9 2.5 2.1 1.7 1.2 7.0

Clamping Force (kN) Non-Usable Range(■) Max. Lever Length Lever Length L(mm) (L) L=80 L=100 L=120 L=140 L=160 L=200 (mm) 5.4 5.1 110 5.1 4.8 4.5 123 4.7 4.4 4.2 139 4.3 4.0 3.8 3.6 159 3.9 3.7 3.5 3.3 3.1 187 3.5 3.3 3.1 3.0 2.8 2.6 227 3.1 2.9 2.8 2.6 2.5 2.3 245 2.7 2.6 2.4 2.3 2.2 2.0 245 2.3 2.2 2.1 2.0 1.9 1.7 245 1.9 1.8 1.7 1.6 1.6 1.4 245 1.6 1.5 1.4 1.3 1.3 1.1 245 1.2 1.1 1.0 1.0 0.9 0.9 245 7.0 7.0 6.6 5.9 5.4 4.8

L=60 7.7 7.1 6.6 6.0 5.5 4.9 4.4 3.8 3.3 2.7 2.2 1.6 7.0

Clamping Force (kN) Non-Usable Range(■) Max. Lever Length Lever Length L(mm) (L) L=80 L=100 L=120 L=140 L=160 L=200 (mm) 7.2 6.9 115 6.7 6.4 6.0 128 6.2 5.9 5.6 5.3 144 5.7 5.4 5.1 4.9 4.6 166 5.2 4.9 4.7 4.4 4.2 194 4.7 4.4 4.2 4.0 3.8 3.5 235 4.1 3.9 3.7 3.5 3.4 3.1 260 3.6 3.4 3.3 3.1 3.0 2.7 260 3.1 2.9 2.8 2.7 2.5 2.3 260 2.6 2.4 2.3 2.2 2.1 1.9 260 2.1 2.0 1.9 1.8 1.7 1.5 260 1.6 1.5 1.4 1.3 1.3 1.2 260 7.0 7.0 6.7 6.1 5.6 4.9

L=50(s=20)

6 5 4

LK C LK W LM/LJ T MA - 2

L=150(s=120) L=200(s=170)

T MA - 1

3

Work Support LD LC

2

0

LK A

L=100(s=70)

Non-Usable Range (■)

T NC TC

1 0

1 2 3 4 5 6 Supply Hydraulic Pressure (MPa)

Air Sensing Lift Cylinder

7

10

Clamping Force Calculation Formula ※1 (kN) F = P ／ ( 0.7485 + 0.0027×L)

Hydraulic Cylinder Force Pressure (kN) (MPa) L=50 7 9.4 7.9 6.5 8.7 7.3 6 8.0 6.8 5.5 7.4 6.2 5 6.7 5.7 4.5 6.0 5.1 4 5.4 4.5 3.5 4.7 4.0 3 4.0 3.4 2.5 3.4 2.8 2 2.7 2.3 1.5 2.0 1.7 Max. Operating Pressure (MPa) 7.0

Cylinder Force

7 Clamping Force (kN)

Hydraulic Cylinder Force Pressure (kN) (MPa) L=50 7 7.2 6.0 6.5 6.7 5.6 6 6.2 5.1 5.5 5.7 4.7 5 5.2 4.3 4.5 4.6 3.9 4 4.1 3.4 3.5 3.6 3.0 3 3.1 2.6 2.5 2.6 2.1 2 2.1 1.7 1.5 1.6 1.3 Max. Operating Pressure (MPa) 7.0

Link Clamp

8

Clamping Force Calculation Formula ※1 (kN) F = P ／ ( 0.9712 + 0.0039×L)

LLW

Cylinder Force

9

Compact Cylinder LL LLR

8 Clamping Force (kN)

LHC0550

L=60(s=25)

LLU

L=100(s=65)

DP

6

L=150(s=115)

DR

5

L=200(s=165)

7

DS DT

4 Block Cylinder

3

DBA

2

Non-Usable Range (■)

1 0

DBC Control Valve

0

1

2

3

4

5

6

Supply Hydraulic Pressure (MPa)

7

BZL BZT BZX/JZG Pallet Clamp VS VT Expansion Locating Pin VL VM VJ VK Pull Stud Clamp FP FQ Customized Spring Cylinder DW A /DW B

324

Double Action Compact Swing Clamp

m od e l

LHC

Allowable Swing Time Graph

Adjustment of Swing Time

90°Swing

(Swing Stroke)

The graph shows allowable swing time against lever inertia moment. Please make sure that the operating time is more than the operation

(Lock Stroke)

Full Stroke

(Total Operation Time)

time shown in the graph. Excessive action speed can reduce stopping accuracy and damage internal parts.

Allowable Locking Time (sec)

90°Swing

0.004 0.003

Full Stroke 0.002 ※1

0.001 0

LHC0400

0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6

0.010 Lever Inertia Moment (kg・m 2 )

Lever Inertia Moment (kg・m 2 )

0.005

0

※2

0

Allowable Locking Time (sec)

90°Swing

0.006 Full Stroke 0.004 ※1

0.002 ※2

0

0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8

Allowable Releasing Time (sec)

LHC0550

Allowable Locking Time (sec)

90°Swing

0.020 0.015 ※1

Full Stroke

0.005 0

LHC0650

0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6

0.025

0.010

Allowable Releasing Time (sec)

※2

0

0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 Allowable Releasing Time (sec)

0.08 Lever Inertia Moment (kg・m 2 )

Lever Inertia Moment (kg・m 2 )

0 0.030

0

LHC0480

0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6

0.008

0

0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8

0

0 0.020 Lever Inertia Moment (kg・m 2 )

LHC0360

Allowable Locking Time (sec) 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 90°Swing

0.016 0.012

Full Stroke 0.008 ※1

0.004 0

※2

0

0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 Allowable Releasing Time (sec)

Allowable Locking Time (sec) 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 90°Swing

0.07 0.06 0.05 0.04

Full Stroke

0.03 0.02

※1

0.01 0

※2

0

0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 Allowable Releasing Time (sec)

Notes ※1. It shows the inertia moment with material lever (LZH□-T). ※2. For any lever inertia moment, minimum 90°swing time should be 0.2 sec for locking and 0.1 sec for releasing or more. 1. The graph shows the allowable action time in regard to the lever inertia moment when the piston rod operates at constant speed. 2. There may be no lever swing action with large inertia depending on supply hydraulic pressure, oil flow and lever mounting position. 3. For speed adjustment of clamp lever, please use meter-out flow control valve. In case of meter-in control, the clamp lever may be accelerated by its own weight during swinging motion (clamp mounted horizontally) or the piston rod may be moving too fast. Please refer to P.1044 for speed control of the hydraulic cylinder. 4. Excessive swing speed can reduce stopping accuracy and damage the internal parts. 5. Please contact us if operational conditions differ from those shown on the graphs.

325

Swing Clamp Digest P.285

Cross Section Model No. Indication Performance External Action Description Specifications Curve Dimensions

Index

Lever Design Dimensions

Accessories

Cautions P.445

High-Power Series

Model

LHC0480 0.020

Lever Inertia Moment (kg・m 2 )

(How to read the allowable swing time graph) When using LHC0480 Lever Inertia Moment：0.0068kg・m

2

①90°Swing Time when Locking ： About 0.44 sec or more ②90°Swing Time when Releasing： About 0.22 sec or more ③Total Lock Operation Time ④Total Release Operation Time

： About 0.8 sec or more ： About 0.4 sec or more

1．The total operation time on the graph represents the allowable

0

Pneumatic Series

Allowable Locking Time (sec) 0.2 0.4 0.6

①

0.8 1.0 1.2 1.4 1.6

③

Hydraulic Series

0.016

Valve / Coupler Hydraulic Unit

0.012

90°Swing Full Stroke (Reference)

0.008 0.0068

Manual Operation Accessories Cautions / Others

0.004 0

operation time when fully stroked.

② 0

0.1 0.2 0.3

④ 0.4 0.5 0.6 0.7 0.8

Allowable Releasing Time (sec)

Hole Clamp SFA SFC Swing Clamp LHA L HC LHS

How to calculate inertia moment (Estimated) ：Inertia Moment (kg・m 2 )

LHW LT /LG

L,L 1 ,L 2 ,K,b：Length (m)

T LA - 2

m,m 1 ,m 2 ,m 3：Mass (kg)

T LB- 2 T LA - 1

① For a rectangular plate (cuboid), the rotating shaft is vertically on one side of the plate.

L1 m2

L

② For a rectangular plate (cuboid), the rotating shaft is vertically on the gravity center of the plate.

③ Load is applied on the lever front end. L2

K L

LK W

b

m

m2

LM/LJ T MA - 2 T MA - 1

L1

L m1

LK A LK C

b

b

Link Clamp

m1

m3

Work Support LD LC T NC TC Air Sensing Lift Cylinder

=m1

4L 2 + b 2 4 L 12+ b 2 +m2 12 12

=m

L 2+ b 2 12

=m1

4 L 2+ b 2 4 L 12+ b 2 L 2 2 +b 2 +m2 + m 3K 2+ m 3 12 12 12

LLW Compact Cylinder LL LLR LLU DP DR DS DT Block Cylinder DBA DBC Control Valve BZL BZT BZX/JZG Pallet Clamp VS VT Expansion Locating Pin VL VM VJ VK Pull Stud Clamp FP FQ Customized Spring Cylinder DW A /DW B

326

Double Action Compact Swing Clamp

m od e l

External Dimensions

Machining Dimensions of Mounting Area

C：Gasket Option (With G Thread Plug)

Release Port φP

JA

B J

2Z

H

Ny

Release Port：G Thread ※3

Nx

Ny

※ The drawing shows the released state of LHC-CR.

(Speed Control Valve Port)

LHC

R Type

0

L

Lock Port φP Swing Direction when Clamping

AA

CA - 0.05

□K

C

φJB

Hexagon Socket Y

4-EA Screw ※4

□K

φ

Remove all burrs

L Type 4-φR Spot Facing φQ

2-G Thread Plug (Included)

+ 0.3 0

C0.6

+0.05

φCC   Slot for Lever Phasing※1 0 R Type (L Type：180°Reverse)

Lock Port：G Thread ※3 (Speed Control Valve Port) Nut (Included)

※5

X Screw

※4. EA tapping depth of the mounting bolt should be decided according to the mounting height referring to dimension 'S'.

Taper Sleeve (Included)

φBB

Fu

T

Notes

BA

CB

V Taper 1/10

W

AB

φAC

dimension 'F'.

F

E

M

S ※2

G

A

φU

-0.1

φD -0.2

Nx

Ny

Ny

Lock Port O-Ring (Included)

Release Port O-Ring (Included)

Notes ※1. The slot for lever phasing faces the oil port side when locked. ※2. Mounting bolts are not provided. Please prepare them based on dimension 'S'. ※3. Speed control valve is sold separately. Please refer to P.727 .

※5. The depth of the body mounting hole φD should be decided according to the mounting height referring to

15°

327

6.3S

φD

Swing Clamp Digest P.285

Cross Section Model No. Indication Performance External Action Description Specifications Curve Dimensions

Index

Lever Design Dimensions

Accessories

Cautions P.445

High-Power Series

Model No. Indication

Pneumatic Series

(Format Example：LHC0550-CR, LHC0750-CL)

R L

LHC 048 0 - C

1 Body Size

2 Design No. 3 Piping Method

4 Swing Direction when Clamping 1

2

3

4

Hydraulic Series Valve / Coupler Hydraulic Unit Manual Operation Accessories Cautions / Others

Hole Clamp SFA SFC Swing Clamp

External Dimensions and Machining Dimensions for Mounting

L HC LHS

Model No.

LHC0360-C□

LHC0400-C□

LHC0480-C□

LHC0550-C□

Full Stroke

11.5

12.5

13.5

14.5

16

Swing Stroke (90° )

5.5

6.5

7.5

8.5

10

Vertical Stroke

6

6

6

6

6

T LB- 2

A

90.5

99.5

108.5

122

133.5

T LA - 1

LHW LT /LG T LA - 2

B

49

54

61

69

81

C

40

45

51

60

70

D

36

40

48

55

65

E

53

58

61

69.5

75.5

LK W

F

28

33

33

39.5

44.5

LM/LJ

Fu

62.5

66.5

75.5

82.5

89

G

25

25

28

30

31

H

29

31.5

35.5

39

46

J

20

22.5

25.5

30

35

LD

K

31.4

34

40

47

55

LC

L

66

73

83

88

106

M

11

11

13

12

13

Link Clamp LK A LK C

T MA - 2 T MA - 1 Work Support

T NC TC Air Sensing Lift Cylinder

Nx

23.5

26

30

33.5

39.5

Ny

8

9

11

12

15

P

3

3

3

3

5

Q

7.5

9

9

11

11

R

4.5

5.5

5.5

6.8

6.8

S

16

15

17.5

17

17

T

13.5

14.5

15.5

16.5

18

DP

U

15

18

22

25

30

DR

V

13

15

18

21

24

W

11

12

14

15

16

X (Nominal×Pitch)

M14×1.5

M16×1.5

M20×1.5

M22×1.5

M27×1.5

Y

5

6

8

8

10

DBA

Z (Chamfer)

C2

C3

C3

C3

C4

DBC

AA

22

24

30

32

41

AB

7

8

9

10

11

AC

24.5

26.5

33

35.5

45

BA

14

16

19

22

25

BB

17

20

25

28

34

CA

6

7

9

10

12.5

CB

6.5

6.5

7.5

9.5

11.5

CC

4

4

5

6

6

EA (Nominal×Pitch)

M4×0.7

M5×0.8

M5×0.8

M6×1

M6×1

JA

3.5

3.5

3.5

3.5

4.5

JB

14

14

14

14

19

VM

G1/8

G1/8

G1/8

G1/8

G1/4

VK

Lock Port : G Thread Release Port : G Thread Cylinder Capacity ※6

Note

cm

3

LLW Compact Cylinder LL LLR LLU

DS DT Block Cylinder

Control Valve BZL BZT BZX/JZG Pallet Clamp VS VT Expansion Locating Pin VL VJ

1BP5

1BP5

1BP5

1BP5

1BP7

Pull Stud Clamp

Lock

4.1

6.3

9.4

14.9

21.4

FP

Release

6.1

9.4

14.5

22.0

32.7

FQ

0.6

0.8

1.2

1.8

2.4

Customized Spring Cylinder

O-Ring

Mass

LHA

（mm） LHC0650-C□

kg

※6. Mass of single swing clamp including taper sleeve and nut.

DW A /DW B

328

Double Action Compact Swing Clamp  Lever Design Dimensions/Accessories

m od e l

LHC

Taper Lock Lever Design Dimension ※ Reference for designing taper lock swing lever. Corresponding Model No.

LHC

0 -

C

R L

1 Body Size

（mm） Corresponding Model No. ※1 LHC0360 LHC0400 LHC0480 LHC0550 LHC0650 φH Ｈ8 Pin Hole for Lever Phasing

G±0.05

+ 0.2 0

A

D

R0.4

17

19

23

26

29

B

14

16

19

22

25

C

3

3

4

4

4

D

10.5

10.5

12.5

14.5

16.5

E

+ 0.027 17  0

+ 0.033 20  0

+ 0.033 25  0

+ 0.033 28  0

+ 0.039 34  0

F

15

17

21

23.5

29

G

8

9

11.5

13

15.5

H

C

C0.6

B±0.1

φF

A

+ 0.018 4  0

+ 0.018 4  0

+ 0.018 5  0

+ 0.018 6  0

+ 0.018 6  0

Phasing Pin (Reference) φ4(h8)×10 φ4(h8)×10 φ5(h8)×12 φ6(h8)×14 φ6(h8)×16 Notes 1. Swing lever should be designed with its length according to performance graph

φE Ｈ8

shown on P.323 and P.324 . 2. If the swing lever is not in accordance with the dimensions shown above, performance may be degraded and damage can occur. 3. The pin hole for lever phasing (φH) should be added if necessary.

329

Swing Clamp Digest P.285

Cross Section Model No. Indication Performance External Action Description Specifications Curve Dimensions

Index

Lever Design Dimensions

Accessories

Cautions P.445

High-Power Series

Accessories：Material Swing Lever for Taper Lock Option Model No. Indication

LZH 048 0 - T Size (Refer to the table)

Design No. (Revision Number)

（mm） Model No.

Pneumatic Series

Hydraulic Series

Corresponding Model No. LＨC0360 LＨC0400 LＨC0480 LＨC0550 LＨC0650 A

120

145

160

170

175

Valve / Coupler Hydraulic Unit

26

32

40

45

50

17

19

23

26

29

Manual Operation Accessories

D

13

16

20

23

25

Cautions / Others

E

14

16

19

22

25

F

17

20

25

28

34

φG+0.2 0

G

15

17

21

23.5

29

C0.6

H

13

16

20

22.5

25

H

B

B C

D

A

R0.4 E

C

LZH0360 LZH0400 LZH0480 LZH0550 LZH0650 -T -T -T -T -T

SFA SFC Swing Clamp

Notes 1. Material : S50CH 2. If necessary, the front end should be additionally machined.

φF

Hole Clamp

3. When determining the phase, refer to the taper lock lever design dimensions for each model to do the additional machining.

LHA L HC LHS LHW LT /LG T LA - 2 T LB- 2 T LA - 1 Link Clamp LK A LK C LK W LM/LJ T MA - 2 T MA - 1 Work Support LD LC T NC TC Air Sensing Lift Cylinder LLW Compact Cylinder LL LLR LLU DP DR DS DT Block Cylinder DBA DBC Control Valve BZL BZT BZX/JZG Pallet Clamp VS VT Expansion Locating Pin VL VM VJ VK Pull Stud Clamp FP FQ Customized Spring Cylinder DW A /DW B

330

Hydraulic Swing Clamp

Cautions

m od e l

LH A/LH S/LT/LG/TLA-2 /TLB-2 /TL A-1

Cautions ● Notes for Design

● Installation Notes

1）Check Specifications

1）Check the Usable Fluid

● Please use each product according to the specifications.

● Please use the appropriate fluid by referring to the Hydraulic Fluid List (P.1043).

2）Notes for Circuit Design ● Please read "Notes on Hydraulic Cylinder Speed Control Circuit" on P. 1044 to assist with proper hydraulic circuit designing. ● Ensure there is no possibility of supplying hydraulic pressure to the lock and release ports simultaneously.

2）Mounting the clamp ● When mounting the clamp, use hexagon socket bolts as multiple bolt holes for mounting (with tensile strength of 12.9) and tighten them with the torque shown in the chart below. Tightening with greater torque than recommended can depress

3）Swing lever should be designed so that the inertia moment is small.

the seating surface or break the bolt.

● Large moment of inertia will degrade the lever s stopping accuracy and cause undue wear to the clamp.

Model No. LHA0360

Additionally, the clamp may not function, depending on supplied

LHS0360 / LHW0360

hydraulic pressure and lever mounting position.

LHA0400 / LHC0400

● Please set the allowable operating time after the inertia moment is

LHS0400 / LHW0400

calculated.

LHA

Please make sure that let the clamps work within allowable operating

LHC

time referring to the allowable operating time graph.

LHS LHW

be protected. ● If spatter gets onto the sliding surface it could lead to malfunction and fluid leakage.

LT/LG

● Make sure the clamp surface and mounting surface of the clamp are parallel.

TLA-2 TLB-2 TLA-1

6）Notes for LHA-M/N, LHW ● When using air sensing swing clamp (LHA-M/N, LHW), make sure to check the Notes for Design・Installation・Use (Pages shown below). ・Swing clamp with air sensing option LHA-M/N: Refer to P.315. ・Swing clamp with air sensing valve LHW: Refer to P.353.

445

LHS0480 / LHW0480 LHA0550 / LHC0550 LHS0550 / LHW0550 LHA0650 / LHC0650

Tightening Torque (N･m)

M4×0.7

4.0

M5×0.8

8.0

M5×0.8

8.0

M6×1

14

M6×1

14

LHA0750 / LHS0750

M8×1.25

33

LHA0900 / LHS0900

M10×1.5

65

LHA1050 / LHS1050

M12×1.75

114

LT0360

M4×0.7

3.2

LT0400

M5×0.8

6.3

LT0480

M5×0.8

6.3

LT0550

M6×1

10

LT0650

M6×1

10

LT0750

M8×1.25

25

LG0900

M10×1.5

58.8

LHS0650 / LHW0650

4）When using on a welding fixture, the exposed area of piston rod should

5）When clamping on a sloped surface of the workpiece

LHA0480 / LHC0480

Thread Size

LG1050

M12×1.75

98

TL□040□-□

M5×0.8

6.9

TL□060□-□

M6×1

11.8

TL□080□-□

M6×1

11.8

TL□100□-□

M8×1.25

25

TL□160□-□

M8×1.25

25

TL□200□-□

M10×1.5

58.8

TL□250□-□

M10×1.5

58.8

TL□400□-□

M12×1.75

98

Swing Clamp Digest P.285

Cautions

High-Power Series Pneumatic Series

③If clamp can't be removed from

3）Mounting and removing the swing lever. piston rod can cause the rod to loosen.

secure the lever while tightening

Clean carefully before assembly.

the nut.

LHA0360 LHA0400 / LHC0400 LHS0400 / LHW0400 LHA LHC LHS LHW

LHA0480 / LHC0480

Tightening Torque (N･m)

M14×1.5

21 ∼ 25

M16×1.5

33 ∼ 40

M22×1.5

84 ∼ 100

M27×1.5

120 ∼ 145

LHA0750 / LHS0750

M30×1.5

175 ∼ 210

LHA0900 / LHS0900

M39×1.5

280 ∼ 335

LHA1050 / LHS1050

M48×1.5

333 ∼ 400

LT0360

M10×1

15 ∼ 18

LT0400

M12×1.5

24 ∼ 29

LT0480

M16×1.5

37 ∼ 45

LT0550

M18×1.5

59 ∼ 71

LT0650

M22×1.5

93 ∼ 112

LT0750

M28×1.5

147 ∼ 177

LG0900

M36×1.5

232 ∼ 282

LG1050

M45×1.5

300 ∼ 360

LHA0550 / LHC0550 LHS0550 / LHW0550 LHA0650 / LHC0650

SFA

During removal ① While the clamp is in the fixture or vise, use a hex wrench to bring the arm to the middle of the swing stroke and then loosen the nut.

Thread Size

Tightening Torque (N･m)

L HS L HW

turns then remove the lever with puller.

L T /L G TLA-2

Do not put any rotating torque on the

T L B- 2

piston rod.

TLA-1 Link Clamp LK A

4）Swinging Speed Adjustment ● Adjust the speed following "Allowable Swing Time Graph". If the clamp operates too fast the parts will wear out leading to ● Please make sure to release air from the circuit before adjusting

LHA0360-F / LHS0360-F

Ｍ6×1

14

speed. It will be difficult to adjust the speed accurately with air mixed

M8×1

33

in the circuit.

LHA0480-F / LHS0480-F

M10×1.25

65

LHA-F

LHA0550-F / LHS0550-F

M12×1.5

100 ∼ 114

LHS-F

LHA0650-F / LHS0650-F

M14×1.5

160 ∼ 180

LHA0750-F / LHS0750-F

M16×1.5

250 ∼ 280

LHA0900-F / LHS0900-F

M20×2

500 ∼ 540

LHA1050-F / LHS1050-F

M24×2

760 ∼ 810

TL□040□-□

Ｍ6×1

13

TL□060□-□

M8×1

32

TL□080□-□

M8×1

32

TL□100□-□

M10×1.25

63

TL□160□-□

M12×1.5

100

TL□200□-□

M14×1.5

160

6）Notes on dual rod option (-D) for dog application.

TL□250□-□

M16×1.5

250

TL□400□-□

M20×2

500

● When attaching dog, set up the piston so that it will not turn around.

TLB-2 TLA-1

Swing Clamp L HC

② Loosen the taper sleeve nut two or three

LHA0400-F / LHS0400-F

TLA-2

SFC

L HA

premature damage and ultimately complete equipment failure.

LHA/LHS-F Quick Change Lever, TLA-2/TLB-2/TLA-1 Standard Model No.

Cautions / Others

tightening the nut.

Hole Clamp

54 ∼ 65

LHS0650 / LHW0650

LT/LG

Thread Size

M20×1.5

LHS0480 / LHW0480

Manual Operation Accessories

middle of the swing stroke before

LHA/LHC/LHS/LHW/LT/LG Standard：Taper Lock Lever

LHS0360 / LHW0360

Valve / Coupler Hydraulic Unit

It is best to bring the lever to the

● Lever arm mounting bolt torques are shown below.

Model No.

Hydraulic Series

fixture for final tightening,

● Oil or debris on the mating surfaces of the lever, taper sleeve or

LK C LK W LM/LJ T MA - 2 T MA - 1 Work Support LD

● Turn the speed control valve gradually from the low-speed side (small flow) to the high-speed side (large flow) to adjust the speed.

LC T NC TC Air Sensing Lift Cylinder LLW

5）Checking looseness and retightening ● At the beginning of the machine installation, the bolt and nut may be tightened lightly. Check the looseness and re-tighten as required.

Compact Cylinder LL LLR

Please secure the dog or cam and prevent any rotation or torque on

DP DR DS DT

the piston rod. ● If the piston rod is subjected to excessive torque or shock, the

LLU

Torque values for the mounting screw are shown in the table below.

rod or the internal mechanism may be damaged. Observe the

Block Cylinder DBA

following points to prevent such shock.

DBC Control Valve

During mounting

BZL

① When the clamp is positioned with

BZT

fixture, determine the lever position,

BZX/JZG

and temporarily tighten the nut for

Pallet Clamp

fixing the lever.

VS

②Remove the clamp from a fixture,

Model No.

Thread Size

Tightening Torque (N･m)

LHA0360-□□D

M4×0.7

3.2

fix the lever by machine vise etc.,

LHA0400-□□D

M6×1

10

and tighten the nut.

LHA0480-□□D

M8×1.25

25

LHA0550-□□D

M8×1.25

25

LHA0650-□□D

M8×1.25

25

LHA0750-□□D

M10×1.5

50

LHA0900-□□D

M10×1.5

50

LHA1050-□□D

M10×1.5

50

VT Expansion Locating Pin VL VM VJ VK Pull Stud Clamp FP FQ

※ Please refer to P.1043 for common cautions.

・Installation Notes

・Hydraulic Fluid List ・Notes on Hydraulic Cylinder Speed Control Circuit

・Notes on Handling ・Maintenance/Inspection ・Warranty

Customized Spring Cylinder DW A /DW B

446

Cautions Cautions ● Installation Notes (For Hydraulic Series)

● Hydraulic Fluid List

1）Check the Usable Fluid

ISO Viscosity Grade ISO-VG-32

Maker

● Please use the appropriate fluid by referring to the Hydraulic Fluid List.

Showa Shell Sekiyu 2）Procedure before Piping ● The pipeline, piping connector and fixture circuits should be cleaned by thorough flushing. ● The dust and cutting chips in the circuit may lead to fluid leakage and malfunction. ● There is no filter provided with Kosmek s product except for a part of valves which prevents foreign materials and contaminants from getting into the circuit. 3）Applying Sealing Tape ● Wrap with tape 1 to 2 times following the screw direction. ● Pieces of the sealing tape can lead to oil leakage and malfunction. ● In order to prevent a foreign substance from going into the product during the piping work, it should be carefully cleaned before working.

4）Air Bleeding of the Hydraulic Circuit ● If the hydraulic circuit has excessive air, the action time may become very long. If air enters the circuit after connecting the hydraulic port or under the condition of no air in the oil tank, please perform the following steps. ① Reduce hydraulic pressure to less than 2MPa. ② Loosen the cap nut of pipe fitting closest to the clamp by one full turn. ③ Wiggle the pipeline to loosen the outlet of pipe fitting. Hydraulic fluid mixed with air comes out.

④ Tighten the cap nut after bleeding. ⑤ It is more effective to bleed air at the highest point inside the circuit or at the end of the circuit. (Set an air bleeding valve at the highest point inside the circuit.)

5）Checking Looseness and Retightening ● At the beginning of the machine installation, the bolt and nut may be tightened lightly. Check the looseness and re-tighten as required.

1043

Idemitsu Kosan JX Nippon Oil & Energy

Anti-Wear Hydraulic Oil Multi-Purpose Hydraulic Oil Tellus S2 M 32

Morlina S2 B 32

Daphne Hydraulic Fluid 32 Daphne Super Multi Oil 32 Super Hyrando 32

Super Mulpus DX 32

Cosmo Hydro AW32

Cosmo New Mighty Super 32

ExxonMobil

Mobil DTE 24

Mobil DTE 24 Light

Matsumura Oil

Hydol AW-32

Cosmo Oil

Castrol Note

Hyspin AWS 32 As it may be difficult to purchase the products as shown in the table from overseas, please contact the respective manufacturer.

Installation Notes (For Hydraulic Series)

Hydraulic Fluid List

Notes on Hydraulic Cylinder Speed Control Circuit

Notes on Handling

Maintenance/Inspection

Warranty

High-Power Series Pneumatic Series

● Notes on Hydraulic Cylinder Speed Control Unit

！

Please pay attention to the cautions below. Design the hydraulic circuit for controlling the action speed of hydraulic cylinder. Improper circuit design may lead to malfunctions and damages. Please review the circuit design in advance.

● Flow Control Circuit for Single Acting Cylinder For spring return single acting cylinders, restricting flow during release can extremely slow down or disrupt release action.

In the case of meter-out circuit, the hydraulic circuit should be designed with the following points. ① Single acting components should not be used in the same

The preferred method is to control the flow during the lock action

flow control circuit as the double acting components.

using a valve that has free-flow in the release direction.

The release action of the single acting cylinders may become

It is also preferred to provide a flow control valve at each actuator.

erratic or very slow.

Hydraulic Series Valve / Coupler Hydraulic Unit Manual Operation Accessories Cautions / Others

Cautions Installation Notes (For Hydraulic Series) Hydraulic Fluid List Notes on Hydraulic Cylinder Speed Control Circuit Notes on Handling Maintenance/ Inspection

Accelerated clamping speed by excessive hydraulic flow to

Warranty

the cylinder may sustain damage. In this case add flow control to regulate flow. (Please add flow control to release flow if the lever weight is put on at the time of release action when using

Refer to the following circuit when both the single acting

swing clamps.)

cylinder and double acting cylinder are used together. Flow Control at the Release Side

○ Separate the control circuit.

Company Profile Company Profile Our Products History

Index Search by Alphabetical Order

Sales Offices

Ｗ

● Flow Control Circuit for Double Acting Cylinder Flow control circuit for double acting cylinder should have meter-out circuits for both the lock and release sides. Meter-in control can

○ Reduce the influence of double acting cylinder control unit.

have adverse effect by presence of air in the system.

However, due to the back pressure in tank line, single action

However, in the case of controlling LKE, TMA, TLA, both lock side

cylinder is activated after double action cylinder works.

and release side should be meter-in circuit. Refer to P.47 for speed adjustment of LKE. For TMA and TLA, if meter-out circuit is used, abnormal high pressure is created, which causes oil leakage and damage.    【Meter-out Circuit】(Except LKE/TMA/TLA)

  

② In the case of meter-out circuit, the inner circuit pressure may increase during the cylinder action because of the fluid supply. The increase of the inner circuit pressure can be prevented by reducing the supplied fluid beforehand via the flow control valve. Especially when using sequence valve or pressure switches for clamping detection. If the back pressure is more than the set pressure then the system will not work as it is designed to.

【Meter-in Circuit】(LKE/TMA/TLA must be controlled with meter-in.)

Sequence Valve

Flow Control Valve (Any location is OK)

1044

Cautions Cautions ● Notes on Handling

● Maintenance and Inspection

1）It should be handled by qualified personnel.

1）Removal of the Machine and Shut-off of Pressure Source

● The hydraulic machine and air compressor should be handled

● Before the machine is removed, make sure that the

and maintained by qualified personnel. 2）Do not handle or remove the machine unless the safety protocols are ensured. ① The machine and equipment can only be inspected or prepared when it is confirmed that the preventive devices are in place.

above-mentioned safety measures are in place. Shut off the air of hydraulic source and make sure no pressure exists in the hydraulic and air circuit. ● Make sure there is no abnormality in the bolts and respective parts before restarting.

② Before the machine is removed, make sure that the above-mentioned safety measures are in place. Shut off the air of hydraulic source

2）Regularly clean the area around the piston rod and plunger.

and make sure no pressure exists in the hydraulic and air circuit.

● If it is used when the surface is contaminated with dirt, it may

③ After stopping the machine, do not remove until the temperature

lead to packing seal damage, malfunctioning , fluid leakage

cools down.

and air leaks.

④ Make sure there is no abnormality in the bolts and respective parts before restarting the machine or equipment. 3）Do not touch clamps (cylinder) while clamps (cylinder) is working. Otherwise, your hands may be injured due to clinching.

3） Please clean out the reference surface regularly (taper reference surface and seating surface) of locating machine .(VS/VT/VL/VM/ VJ/VK/WVS/WM/WK/VX/VXF) 4）Do not disassemble or modify. ● If the equipment is taken apart or modified, the warranty will be voided even within the warranty period.

● Location products, except VX/VXF model, can remove contaminants with cleaning functions. When installing pallets makes sure there is no thick sludge like substances on pallets. ● Continuous use with dirt on components will lead to locating functions not work properly, leaking and malfunction.

4） If disconnecting by couplers on a regular basis, air bleeding should be carried out daily to avoid air mixed in the circuit. 5）Regularly tighten nuts, bolts, pins, cylinders and pipe line to ensure proper use. 6）Make sure the hydraulic fluid has not deteriorated. 7）Make sure there is smooth action and no abnormal noise. ● Especially when it is restarted after left unused for a long period, make sure it can be operated correctly. 8）The products should be stored in the cool and dark place without direct sunshine or moisture. 9）Please contact us for overhaul and repair.

1045

Installation Notes (For Hydraulic Series)

Hydraulic Fluid List

Notes on Hydraulic Cylinder Speed Control Circuit

Notes on Handling

Maintenance/Inspection

Warranty

High-Power Series

● Warranty

Pneumatic Series

1）Warranty Period

Hydraulic Series

● The product warranty period is 18 months from shipment from our factory or 12 months from initial use, whichever is earlier. 2）Warranty Scope ● If the product is damaged or malfunctions during the warranty period due to faulty design, materials or workmanship, we will

Valve / Coupler Hydraulic Unit Manual Operation Accessories Cautions / Others

replace or repair the defective part at our expense. Defects or failures caused by the following are not covered. ① If the stipulated maintenance and inspection are not carried out. ② If the product is used while it is not suitable for use based on the operator s judgment, resulting in defect. ③ If it is used or handled in inappropriate way by the operator. （Including damage caused by the misconduct of the third party.） ④ If the defect is caused by reasons other than our responsibility. ⑤ If repair or modifications are carried out by anyone other than Kosmek, or without our approval and confirmation, it will void warranty. ⑥ Other caused by natural disasters or calamities not attributable to our company. ⑦ Parts or replacement expenses due to parts consumption and

Cautions Installation Notes (For Hydraulic Series) Hydraulic Fluid List Notes on Hydraulic Cylinder Speed Control Circuit Notes on Handling Maintenance/ Inspection Warranty

Company Profile Company Profile Our Products History

deterioration. (Such as rubber, plastic, seal material and some electric components.) Damages excluding from direct result of a product defect shall be excluded from the warranty.

Index Search by Alphabetical Order

Sales Offices

1046

C o n t r o l Val v e Mode l Mode l Mode l Mode l

B ZL B ZT B ZX JZG

Directly mounted to clamps, flow control valve・Air bleeding・plug

Directly mounted to clamps Flow control valve, air bleeding valve, G-thread plug for G-thread (-C option) directly mounted.

G Thread Plug

Adjusting Screw

Lock Nut Speed Control Valve

Sp e e d C o n t ro l V a l ve

727

Model

B ZL

Model

B ZT

A i r B le e d V alv e M ode l

BZ X

G T h r e a d P lu g M ode l

JZG

Control Valve Digest

Operating Pressure Range Speed Control Valve （For Low Pressure）

Mod e l

BZ L

→ P.729

High-Power Series

Action Description

Pneumatic Series

Hydraulic Series

A d ju s t t h e f low b y w r e n c h . It can adjust the clamping action speed individually.

Valve / Coupler Hydraulic Unit Manual Operation Accessories

7 M Pa or less

C la mps

Cautions / Others

F low C ontrol

Hole Clamp SFA SFC Swing Clamp LHA LHC

Speed Control Valve （For High Pressure）

LHS LHW

A i r b le e d i n g i n t h e c i r c u i t i s p os s i b le b y loos e n i n g f low c on t r ol v a lv e .

LT /LG T LA - 2 T LB- 2 T LA - 1

Mod e l

BZT

→ P.733

35M Pa or less

Link Clamp LK A LK C LK W LM/LJ T MA - 2 T MA - 1 Work Support LD

Air Bl e e d Val v e Air bleeding in the circuit is possible by wrench.

LC T NC TC Air Sensing Lift Cylinder LLW Compact Cylinder

Mod e l

BZ X

→ P.735

LL

25M Pa or less

LLR LLU DP DR DS DT Block Cylinder DBA DBC Control Valve

G Th re ad Pl ug A i r b le e d i n g i n t h e c i r c u i t i s p os s i b le b y loos e n i n g G t h r e a d p lu g .

BZ L BZ T BZ X /JZ G Pallet Clamp VS VT

Mod e l

JZG

→ P.737

35M Pa or less

Expansion Locating Pin VL VM VJ VK Pull Stud Clamp FP FQ Customized Spring Cylinder DW A /DW B

728

Control Valve  Speed Control Valve（For Low Pressure）

model

BZL

Model No. Indication（Speed Control Valve for Low Pressure）

B ZL 0 10 0 - B 1

2

3

1 G Thread Size 10 ： Thread Part G1/8A Thread 20 ： Thread Part G1/4A Thread

Thread Part

30 ： Thread Part G3/8A Thread

2 Design No. 0 ： Revision Number

3 Control Method

A

A ： Meter-in

B

Circuit Symbol：Meter-in

B ： Meter-out

Circuit Symbol：Meter-out

P1 port Hydraulic Pressure Supply Side

P2 Port Clamp Side

P1 port Hydraulic Pressure Supply Side

P2 Port Clamp Side

Specifications BZL0100-A

Model No. Max. Operating Pressure

MPa

Withstanding Pressure

MPa

BZL0200-A

BZL0100-B

G1/8A

Cracking Pressure

MPa

Max. Passage Area

mm2

BZL0300-B

10.5 Meter-in

G Thread Size

BZL0200-B

7

Control Method

G1/4A

Meter-out G3/8A

G1/8A

0.04 2.6

5.0

G1/4A

Operating Temperature

11.6

2.6

5.0

10.2

25

35

0 ∼ 70

℃

Tightening Torque for Main Body N･m

10

25

35

10

1. Minimum passage area when fully opened is the same as the maximum passage area in the table above. 2. It must be mounted with recommended torque. Because of the structure of the metal seal, if mounting torque is insufficient, the flow control valve may not be able to adjust the flow rate. 3. Don t use used BZL to other clamps. Flow control will not be made because the bottom depth difference of G thread makes metal seal insufficient.

729

G3/8A

0.12 General Hydraulic Oil Equivalent to ISO-VG-32

Usable Fluid

Notes

BZL0300-A

Control Valve Digest

Model No. Indication

Specifications

Applicable Products

Flow Rate Graph

External Dimensions

High-Power Series

Applicable Products Model No.

BZL0100-A

DBA (Single Action) DBC (Single Action) LC (Single Action) Work Support

LHA (Double Action) LHC (Double Action) LHE (Double Action) LHS (Double Action) LHW (Double Action)

Block Cylinder

Block Cylinder

Swing Clamp

Swing Clamp

High-Power Swing Clamp

Swing Clamp

Swing Clamp

(DBA0250-C□)

(DBC0250-C□)

LC0402-C□□-□ （LHA0360-C□□-□）（LHC0360-C□□-□）

（LHS0360-C□□-□）（LHW0400-C□□-□）

(DBA0320-C□)

(DBC0320-C□)

LC0482-C□□-□ （LHA0400-C□□-□）（LHC0400-C□□-□）

（LHS0400-C□□-□）（LHW0480-C□□-□）

LC0552-C□□-□ （LHA0480-C□□-□）（LHC0480-C□□-□）

（LHS0480-C□□-□）（LHW0550-C□□-□）

LC0652-C□□-□ （LHA0550-C□□-□）（LHC0550-C□□-□）

（LHS0550-C□□-□）

DBA0250-C□

DBC0250-C□

LHA0360-C□□-□

LHC0360-C□□-□

LHE0300-C□

LHS0360-C□□-□

LHW0400-C□□-□

DBA0320-C□

DBC0320-C□

LHA0400-C□□-□

LHC0400-C□□-□

LHE0360-C□

LHS0400-C□□-□

LHW0480-C□□-□

LHA0480-C□□-□

LHC0480-C□□-□

LHE0400-C□

LHS0480-C□□-□

LHW0550-C□□-□

LHA0550-C□□-□

LHC0550-C□□-□

LHE0480-C□

LHS0550-C□□-□

BZL0100-B

Pneumatic Series

Hydraulic Series Valve / Coupler Hydraulic Unit Manual Operation Accessories Cautions / Others

LHE0550-C□ BZL0200-A BZL0200-B

(DBA0400-C□)

(DBC0400-C□)

LC0752-C□□-□ （LHA0650-C□□-□）（LHC0650-C□□-□）

（LHS0650-C□□-□） (LHW0650-C□□-□)

(DBA0500-C□)

(DBC0500-C□)

LC0902-C□□-□ （LHA0750-C□□-□）

（LHS0750-C□□-□）

DBA0400-C□

DBC0400-C□

DBA0500-C□

DBC0500-C□

LHA0650-C□□-□

BZL0300-A BZL0300-B

LHC0650-C□□-□

LHS0650-C□□-□

LHW0650-C□□-□

Hole Clamp SFA SFC

LHA0750-C□□-□

LHS0750-C□□-□

（LHA0900-C□□-□）

（LHS0900-C□□-□）

LHA

（LHA1050-C□□-□）

（LHS1050-C□□-□）

LHC

LHA0900-C□□-□

LHS0900-C□□-□

LHA1050-C□□-□

LHS1050-C□□-□

Swing Clamp

LHS LHW LT /LG T LA - 2

Model No.

BZL0100-A

LT/LG (Single Action) LKA (Double Action) LKC (Double Action) LKE (Double Action) LKW (Double Action) LM/LJ (Single Action) Swing Clamp

Link Clamp

Link Clamp

High-Power Link Clamp

Link Clamp

Link Clamp

LL (Double Action)

LLR (Double Action)

T LB- 2

Linear Cylinder Linear Cylinder

T LA - 1

LT0360-C□ （LKA0360-C□□-□）（LKC0400-C□-□）

LKE0300-C□ （LKW0400-C□□-□） LM0360-C □

（ LL0360-C□□-□ ）（LLR0360-C□□-□-□）

LT0400-C□ （LKA0400-C□□-□）（LKC0480-C□-□）

LKE0360-C□ （LKW0480-C□□-□） LM0400-C□

（ LL0400-C□□-□ ）（LLR0400-C□□-□-□）

LT0480-C□ （LKA0480-C□□-□）（LKC0550-C□-□）

LKE0400-C□ （LKW0550-C□□-□） LM0480-C□

（ LL0480-C□□-□ ）（LLR0480-C□□-□-□）

LT0550-C□ （LKA0550-C□□-□）

LKE0480-C□

（ LL0550-C□□-□ ）（LLR0550-C□□-□-□）

LM0550-C□

LKA0360-C□□-□

LKC0400-C□-□

LKW0400-C□□-□

LL0360-C□□-□

LLR0360-C□□-□-□

LKA0400-C□□-□

LKC0480-C□-□

LKW0480-C□□-□

LL0400-C□□-□

LLR0400-C□□-□-□

LKA0480-C□□-□

LKC0550-C□-□

LKW0550-C□□-□

LL0480-C□□-□

LLR0480-C□□-□-□

LL0550-C□□-□

LLR0550-C□□-□-□

LKA0550-C□□-□ BZL0200-A

LT0650-C□ （LKA0650-C□□-□） (LKC0650-C□-□)

BZL0200-B BZL0300-A

（LKW0650-C□□-□） LM0650-C□

（ LL0650-C□□-□ ）（LLR0650-C□□-□-□）

LM0750-C□

（ LL0750-C□□-□ ）（LLR0750-C□□-□-□）

LT0750-C□ （LKA0750-C□□-□） LKA0650-C□□-□

LKC0650-C□-□

LKW0650-C□□-□

LKA0750-C□□-□

LL0650-C□□-□

LLR0650-C□□-□-□

LL0750-C□□-□

LLR0750-C□□-□-□

LG0900-C□ （LKA0900-C□□-□）

LJ0902-C□

（ LL0900-C□□-□ ）（LLR0900-C□□-□-□）

LG1050-C□ （LKA1050-C□□-□）

LJ1052-C□

（ LL1050-C□□-□ ）（LLR1050-C□□-□-□）

BZL0300-B

LK A LK C LK W LM/LJ

LKE0550-C□

BZL0100-B

Link Clamp

LKA0900-C□□-□

LL0900-C□□-□

LLR0900-C□□-□-□

LKA1050-C□□-□

LL1050-C□□-□

LLR1050-C□□-□-□

T MA - 2 T MA - 1 Work Support LD LC T NC TC Air Sensing Lift Cylinder LLW Compact Cylinder LL LLR LLU

Model No.

LLW (Double Action)

DP

Lift Cylinder

DR

（LLW0360-C□□-□） BZL0100-A （LLW0400-C□□-□） （LLW0480-C□□-□） BZL0100-B

DT Block Cylinder

LLW0360-C□□-□

DBA

LLW0400-C□□-□

DBC

LLW0480-C□□-□ Note

DS

1. Flow control circuit for double acting cylinder both should have meter-out circuits for the locking side and release side except model LKE/TLA/TMA. Meter-in controls can be adversely affected by any air in the system.

Control Valve BZ L BZT BZX/JZG Pallet Clamp VS VT Expansion Locating Pin VL VM VJ VK Pull Stud Clamp FP FQ Customized Spring Cylinder DW A /DW B

730

Control Valve  Speed Control Valve（For Low Pressure）

model

BZL

Flow Rate Graph < Hydraulic Fluids ISO-VG32（25∼35℃）> BZL0100-A：Meter-in

BZL0200-A：Meter-in

Controlled Flow Direction

Controlled Flow Direction

Pressure Loss 5MPa

6

0

1

2

3

0

4

0

←Closed Number of Turns of Adjusting Screw Opened→

1

3

4

5

0

1

Controlled Flow Direction

2

4

5

0

1

2

3

0

1

30 20

2

3

3

4

Pressure Loss (MPa)

1

5

6

3

4

Free Flowing Direction 　

Fully Opened

25 20 15

0

1

2

3

4

Pressure Loss (MPa)

5

Fully Closed

10

Fully Closed

5 0

2

←Closed Number of Turns of Adjusting Screw Opened→

Flow Rate (L/min)

Flow Rate (L/min)

2 2

0

30

Fully Opened

10

Fully Closed

1

0

4

15

0

5

35

20

6 4

Pressure Loss 1MPa

10

Free Flowing Direction

Fully Opened

6

Pressure Loss 3MPa

15

25

8

5

Pressure Loss 5MPa

25

←Closed Number of Turns of Adjusting Screw Opened→

Free Flowing Direction 10

4

Controlled Flow Direction

Pressure Loss 1MPa

5 0

4

3

BZL0300-B：Meter-out

Pressure Loss 3MPa

10

Pressure Loss 1MPa

2

2

1

Pressure Loss (MPa)

Pressure Loss 5MPa

15

Pressure Loss 3MPa

4

0

35

20

Pressure Loss 5MPa

6

0

6

Flow Rate (L/min)

8

5

Controlled Flow Direction

Flow Rate (L/min)

Flow Rate (L/min)

3

Fully Closed

10

25

←Closed Number of Turns of Adjusting Screw Opened→

Flow Rate (L/min)

15

Fully Closed

BZL0200-B：Meter-out

10

4

Fully Opened

Pressure Loss (MPa)

BZL0100-B：Meter-out

3

20

5 0

6

2

30

Flow Rate (L/min)

Flow Rate (L/min)

Flow Rate (L/min)

2 2

1

←Closed Number of Turns of Adjusting Screw Opened→

25

10

Fully Closed

1

0

　 Free Flowing Direction

15

0

0

4

Fully Opened

Pressure Loss (MPa)

731

3

35

20

6

0

2

5

　 Free Flowing Direction

Fully Opened

4

Pressure Loss 1MPa

10

25

8

Pressure Loss 3MPa

15

←Closed Number of Turns of Adjusting Screw Opened→

Free Flowing Direction 10

0

20

Pressure Loss 1MPa

5

Pressure Loss 5MPa

25

Pressure Loss 3MPa

10

Pressure Loss 1MPa

2

30

Pressure Loss 5MPa

15

Pressure Loss 3MPa

4

35

20

Flow Rate (L/min)

Flow Rate (L/min)

8

0

Controlled Flow Direction

25

Flow Rate (L/min)

10

0

BZL0300-A：Meter-in

6

5 0

0

1

2

3

4

Pressure Loss (MPa)

5

6

Control Valve Digest

Model No. Indication

Applicable Products

Specifications

External Dimensions

Flow Rate Graph

High-Power Series

External Dimensions

Pneumatic Series

Hydraulic Series

(Clamp/Cylinder)

Adjusting Screw M Screw

Exclusive Packing (Included)

Manual Operation Accessories

BZL0□00 -□

φB

Hex. Socket L

Valve / Coupler Hydraulic Unit

G Thread

Cautions / Others

P2 Port Clamp Side

Hole Clamp

CLOSE

J

OPEN

Hexagon K

SFA

E

max.H

SFC

D max.C

Hexagon A

F P1 Port Hydraulic Pressure Supply Side

Machining Dimensions of Mounting Area

Z

0

（mm）

P2 Port Clamp Side

φW

45°

0.4

φV

Q

P1 Port Hydraulic Pressure Supply Side

2. Since the

LHS

BZL0100-□

BZL0200-□

BZL0300-□

A

14

18

22

LT /LG

B

15.5

20

24

T LA - 2

C

15

16

19

D

12

13

16

LHW

T LB- 2 T LA - 1

E

8.5

9.5

11

F

(11.6)

(15.1)

(17.6)

LK A

G

G1/8

G1/4

G3/8

LK C

H

3

3

3

J

3.5

3.5

5

K

10

10

13

L

3

3

4

M

M6×0.75

M6×0.75

M8×0.75

N

11.5

15

17.5

P

8.5

11※1

13

Q

9

11.5

13

R (Flat Surface Area)

16

20.5

24.5 17

S

10

13.5

T

8.7

11.5

15

U

G1/8

G1/4

G3/8

V

2∼3

3∼4

4∼5

W

2.5 ∼ 5

3.5 ∼ 7

4.5 ∼ 9

Link Clamp

LK W LM/LJ T MA - 2 T MA - 1 Work Support LD LC T NC TC Air Sensing Lift Cylinder LLW Compact Cylinder LL LLR LLU

Notes 1. Since the

LHC

Model No.

min.P

0.2 φT

min.φR

LHA

N - 0.10

U Thread ⊥ 0.1 Z (Prepared HoleφT Flat Bottom)

max.φS

Attention

Swing Clamp

DP

area is sealing part, be careful not to damage it. area is the metal sealing part of BZL, be careful not to damage it. (Especially when deburring)

3. No cutting chips or burr should be at the tolerance part of machining hole. 4. As shown in the drawing, P1 port is used as the hydraulic supply and P2 port as the clamp side. 5. If mounting plugs or fittings with G thread specification available in the market, the dimension '※1' should be 12.5.

DR DS DT Block Cylinder DBA DBC

Notes 1. Please read "Notes on Hydraulic Cylinder Speed Control Circuit" to assist with proper hydraulic circuit design. If there is something wrong with the circuit design, it leads to the applications malfunction and damage. (Refer to P.1044) 2. It is dangerous to air bleed during operation under high pressure. It must be done under lower pressure. (For reference: the minimum operating range of the product within the circuit.)

Control Valve BZ L BZT BZX/JZG Pallet Clamp VS VT Expansion Locating Pin VL VM VJ VK Pull Stud Clamp FP FQ Customized Spring Cylinder DW A /DW B

732

Control Valve  Air Bleed Valve

model

BZX

Model No. Indication（Air Bleed Valve）

B ZX0 1 0 1

2

1 G Thread Size 1

： Thread Part G1/8A Thread

2

： Thread Part G1/4A Thread

3

： Thread Part G3/8A Thread

Thread Part

2 Design No. 0 ： Revision Number

Specifications

Circuit Symbol BZX010

Model No. Max. Operating Pressure

MPa

Withstanding Pressure

MPa

37.5 G1/4A

G3/8A

General Hydraulic Oil Equivalent to ISO-VG-32

Usable Fluid Operating Temperature

0 ∼ 70

℃

Tightening Torque for Main Body N･m Notes

BZX030

25 G1/8A

G Thread Size

BZX020

10

35

25

1. Do not over loosen the plug during air venting. （Do not loosen for more than 2 turns from the fully closed position.） 2. It is dangerous to have air venting operation under high pressure. It must be done under lower pressure. （For reference: the minimum operation pressure range of the product within the circuit） 3. Refer to the processing dimensions for BZL mounting area.

Applicable Products Model No.

DBA (Single Action) DBC (Single Action) LC (Single Action)

LHA (Double Action) LHC (Double Action) LHE (Double Action) LHS (Double Action) LHW (Double Action)

Block Cylinder

Block Cylinder

Work Support

Swing Clamp

Swing Clamp

High-Power Swing Clamp

Swing Clamp

Swing Clamp

DBA0250-C□

DBC0250-C□

LC0402-C□□-□

LHA0360-C□□-□

LHC0360-C□□-□

LHE0300-C□

LHS0360-C□□-□

LHW0400-C□□-□

DBA0320-C□

DBC0320-C□

LC0482-C□□-□

LHA0400-C□□-□

LHC0400-C□□-□

LHE0360-C□

LHS0400-C□□-□

LHW0480-C□□-□

LC0552-C□□-□

LHA0480-C□□-□

LHC0480-C□□-□

LHE0400-C□

LHS0480-C□□-□

LHW0550-C□□-□

LC0652-C□□-□

LHA0550-C□□-□

LHC0550-C□□-□

LHE0480-C□

LHS0550-C□□-□

LHC0650-C□□-□

BZX010

LHE0550-C□ BZX020

DBA0400-C□

DBC0400-C□

LC0752-C□□-□

LHA0650-C□□-□

DBA0500-C□

DBC0500-C□

LC0902-C□□-□

LHA0750-C□□-□

LHS0750-C□□-□

LHA0900-C□□-□

LHS0900-C□□-□

LHA1050-C□□-□

LHS1050-C□□-□

BZX030

Model No.

BZX010

LHS0650-C□□-□

LT/LG (Single Action) LKA (Double Action) LKC (Double Action) LKE (Double Action) LKW (Double Action) LM/LJ (Single Action) LL (Double Action) Swing Clamp

Link Clamp

Link Clamp

High-Power Link Clamp

Link Clamp

Link Clamp

LHW0650-C□□-□

LLR (Double Action)

Linear Cylinder Linear Cylinder

LT0360-C□

LKA0360-C□□-□

LKC0400-C□-□

LKE0300-C□

LKW0400-C□□-□

LM0360-C □

LL0360-C□□-□

LLR0360-C□□-□-□

LT0400-C□

LKA0400-C□□-□

LKC0480-C□-□

LKE0360-C□

LKW0480-C□□-□

LM0400-C□

LL0400-C□□-□

LLR0400-C□□-□-□

LT0480-C□

LKA0480-C□□-□

LKC0550-C□-□

LKE0400-C□

LKW0550-C□□-□

LM0480-C□

LL0480-C□□-□

LLR0480-C□□-□-□

LT0550-C□

LKA0550-C□□-□

LM0550-C□

LL0550-C□□-□

LLR0550-C□□-□-□ LLR0650-C□□-□-□

LKE0480-C□ LKE0550-C□

BZX020 BZX030

Model No.

LT0650-C□

LKA0650-C□□-□

LM0650-C□

LL0650-C□□-□

LT0750-C□

LKA0750-C□□-□

LM0750-C□

LL0750-C□□-□

LLR0750-C□□-□-□

LG0900-C□

LKA0900-C□□-□

LJ0902-C□

LL0900-C□□-□

LLR0900-C□□-□-□

LG1050-C□

LKA1050-C□□-□

LJ1052-C□

LL1050-C□□-□

LLR1050-C□□-□-□

LLW (Double Action) Lift Cylinder LLW0360-C□□-□

BZX010

LLW0400-C□□-□ LLW0480-C□□-□

735

LKC0650-C□-□

LKW0650-C□□-□

Control Valve Digest P.727

Model No. Indication

Specifications

Applicable Products

External Dimensions

High-Power Series

External Dimensions Exclusive Packing (Included) Body Lock Nut M6（3 types）

Pneumatic Series

(Clamp / Cylinder)

Plug M6x1

Hydraulic Series

G Thread

（mm） BZX010

BZX020

A

14

18

22

B

15.5

20

24

C

19.8

20.6

20.6

D

9.3

10.1

10.1

φB

Model No.

3.6 Hexagon Socket 3 Hexagon 10 Hexagon A

3.8

E D

10.5 C

BZX030

E

5.5

6.3

6.3

G

G1/8

G1/4

G3/8

Valve / Coupler Hydraulic Unit Manual Operation Accessories Cautions / Others

Hole Clamp SFA SFC Swing Clamp LHA LHC LHS LHW LT /LG T LA - 2 T LB- 2 T LA - 1 Link Clamp LK A LK C LK W LM/LJ T MA - 2 T MA - 1 Work Support LD LC T NC TC Air Sensing Lift Cylinder LLW Compact Cylinder LL LLR LLU DP DR DS DT Block Cylinder DBA DBC Control Valve BZL BZT BZ X /JZ G Pallet Clamp VS VT Expansion Locating Pin VL VM VJ VK Pull Stud Clamp FP FQ Customized Spring Cylinder DW A /DW B

736

Control Valve  G Thread Plug

m od e l

JZG

Model No. Indication (G Thread Plug with Air Bleeding Function)

JZG0 1 0 1

2

1 G Thread Size 1

： Thread Part G1/8A Thread

2

： Thread Part G1/4A Thread

3

： Thread Part G3/8A Thread

Thread Part

2 Design No. 0 ： Revision Number

Specifications JZG010

Model No. Max. Operating Pressure

MPa

Withstanding Pressure

MPa

42 G1/4A

G3/8A

General Hydraulic Oil Equivalent to ISO-VG-32

Usable Fluid Operating Temperature

0 ∼ 70

℃

Tightening Torque for Main Body N･m Notes

JZG030

35 G1/8A

G Thread Size

JZG020

10

35

25

1. It is dangerous to have air venting operation under high pressure. It must be done under lower pressure. （For reference: the minimum operation pressure range of the product within the circuit） 2. Refer to the processing dimensions for BZL mounting area.

Applicable Products Model No.

DBA (Single Action) DBC (Single Action) LC (Single Action)

LHA (Double Action) LHC (Double Action) LHE (Double Action) LHS (Double Action) LHW (Double Action)

Block Cylinder

Block Cylinder

Work Support

Swing Clamp

Swing Clamp

High-Power Swing Clamp

Swing Clamp

Swing Clamp

DBA0250-C□

DBC0250-C□

LC0402-C□□-□

LHA0360-C□□-□

LHC0360-C□□-□

LHE0300-C□

LHS0360-C□□-□

LHW0400-C□□-□

DBA0320-C□

DBC0320-C□

LC0482-C□□-□

LHA0400-C□□-□

LHC0400-C□□-□

LHE0360-C□

LHS0400-C□□-□

LHW0480-C□□-□

LC0552-C□□-□

LHA0480-C□□-□

LHC0480-C□□-□

LHE0400-C□

LHS0480-C□□-□

LHW0550-C□□-□

LC0652-C□□-□

LHA0550-C□□-□

LHC0550-C□□-□

LHE0480-C□

LHS0550-C□□-□

LHC0650-C□□-□

JZG010

LHE0550-C□ JZG020

DBA0400-C□

DBC0400-C□

LC0752-C□□-□

LHA0650-C□□-□

DBA0500-C□

DBC0500-C□

LC0902-C□□-□

LHA0750-C□□-□

LHS0750-C□□-□

LHA0900-C□□-□

LHS0900-C□□-□

LHA1050-C□□-□

LHS1050-C□□-□

JZG030

Model No.

JZG010

LHS0650-C□□-□

LT/LG (Single Action) LKA (Double Action) LKC (Double Action) LKE (Double Action) LKW (Double Action) LM/LJ (Single Action) LL (Double Action) Swing Clamp

Link Clamp

Link Clamp

High-Power Link Clamp

Link Clamp

Link Clamp

LHW0650-C□□-□

LLR (Double Action)

Linear Cylinder Linear Cylinder

LT0360-C□

LKA0360-C□□-□

LKC0400-C□-□

LKE0300-C□

LKW0400-C□□-□

LM0360-C □

LL0360-C□□-□

LLR0360-C□□-□-□

LT0400-C□

LKA0400-C□□-□

LKC0480-C□-□

LKE0360-C□

LKW0480-C□□-□

LM0400-C□

LL0400-C□□-□

LLR0400-C□□-□-□

LT0480-C□

LKA0480-C□□-□

LKC0550-C□-□

LKE0400-C□

LKW0550-C□□-□

LM0480-C□

LL0480-C□□-□

LLR0480-C□□-□-□

LT0550-C□

LKA0550-C□□-□

LM0550-C□

LL0550-C□□-□

LLR0550-C□□-□-□ LLR0650-C□□-□-□

LKE0480-C□ LKE0550-C□

JZG020 JZG030

Model No.

JZG010

JZG020

737

LT0650-C□

LKA0650-C□□-□

LM0650-C□

LL0650-C□□-□

LT0750-C□

LKA0750-C□□-□

LKC0650-C□-□

LKW0650-C□□-□

LM0750-C□

LL0750-C□□-□

LLR0750-C□□-□-□

LG0900-C□

LKA0900-C□□-□

LJ0902-C□

LL0900-C□□-□

LLR0900-C□□-□-□

LG1050-C□

LKA1050-C□□-□

LJ1052-C□

LL1050-C□□-□

LLR1050-C□□-□-□

LLW (Double Action) TLA-2 (Double Action) TLB-2 (Double Action) TLA-1 (Single Action) TMA-2 (Double Action) TMA-1 (Single Action) Lift Cylinder

Swing Clamp

Swing Clamp

Swing Clamp

Link Clamp

Link Clamp

LLW0360-C□□-□

TLA0401-2C□-□

TLB0401-2C□-□

TLA0402-1C□

TMA0250-2C□

TMA0250-1C□

LLW0400-C□□-□

TLA0601-2C□-□

TLB0601-2C□-□

TLA0602-1C□

TMA0400-2C□

TMA0400-1C□

LLW0480-C□□-□

TLA0801-2C□-□

TLB0801-2C□-□

TLA0802-1C□

TMA0600-2C□

TMA0600-1C□

TLA1001-2C□-□

TLB1001-2C□-□

TLA1002-1C□

TMA1000-2C□

TMA1000-1C□

TLA1601-2C□-□

TLB1601-2C□-□

TLA1602-1C□

TLA2001-2C□-□

TLB2001-2C□-□

TLA2002-1C□

TMA1600-2C□

TMA1600-1C□

TLA2501-2C□-□

TLB2501-2C□-□

TLA2502-1C□

TMA2500-2C□

TMA2500-1C□

TLA4001-2C□-□

TLB4001-2C□-□

TLA4002-1C□

TMA3200-2C□

TMA3200-1C□

Control Valve Digest P.727

Model No. Indication

Specifications

Applicable Products

External Dimensions

High-Power Series

External Dimensions

Pneumatic Series

Hydraulic Series

Exclusive Packing (Included)

（mm）

φA

G Thread

Model No.

Hexagon Socket D

JZG010

JZG020

JZG030

A

14

18

22

B

3.5

4.5

4.5

C

8

9

10

D

5

6

8

G

G1/8A

G1/4A

G3/8A

Valve / Coupler Hydraulic Unit Manual Operation Accessories Cautions / Others

Hole Clamp

B

C

SFA SFC Swing Clamp LHA LHC LHS LHW LT /LG T LA - 2 T LB- 2 T LA - 1 Link Clamp LK A LK C LK W LM/LJ T MA - 2 T MA - 1 Work Support LD LC T NC TC Air Sensing Lift Cylinder LLW Compact Cylinder LL LLR LLU DP DR DS DT Block Cylinder DBA DBC Control Valve BZL BZT BZ X /JZ G Pallet Clamp VS VT Expansion Locating Pin VL VM VJ VK Pull Stud Clamp FP FQ Customized Spring Cylinder DW A /DW B

738

Manifold Block Mode l Mode l Mode l Mode l Mode l Mode l Mode l Mode l

WH Z- M D L ZY -M D L Z-MS L Z-MP T MZ-1 M B T MZ-2 M B DZ-M G□ DZ-M S □

Manifold Block The mounting height of clamp is adjustable with the manifold block.

Clamp

Workpiece

Manifold Block

Manifold Block

Fixture Base

1023

Manifold Block Applicable Model/Application Examples

Manifold Block Model No. Indication/External Dimensions

High-Power Series

Applicable Model

Pneumatic Series

Manifold Block Model No.

Corresponding Item Model No. Hydraulic Series

Mod e l

Mod e l

Mod e l

W H Z -MD LZ Y-MD LZ - MS

Mode l

WCA

M ode l

WH A

Mode l

WCE

M ode l

WH E

Mode l

LKA

M ode l

LKE

M ode l

LH C

M ode l

LH S

Mode l

LKC

M ode l

LH A

M ode l

LH E

M ode l

LL

Mode l

LM

M ode l

LT

Mode l

LJ

M ode l

LG

Valve / Coupler Hydraulic Unit Manual Operation Accessories Cautions / Others

Screw Locator VXF Manual Expansion Locating Pin VX

Mod e l

LZ - M P

Mode l

LC

M ode l

TC

Manifold Block WHZ - MD L Z Y - MD

Mod e l

TM Z -1MB

Mode l

L Z - MS

TMA-1

L Z - MP T MZ - 1 MB T MZ - 2 MB

Mod e l

TM Z -2MB

Mode l

DZ - M

TMA-2

Manifold Block / Nut DZ- R

Mod e l

D Z -MG□/MS□

Mode l

DZ- C

DP

DZ- P DZ- B LZ- S LZ- SQ

Application Examples

T NZ- S T NZ- SQ

Work Support (LC) Application Example

Pressure Switch

Manifold Block (LZ□-MP×three pieces)

JB

This drawing shows ▼surface is machined by customer one out of three pieces

Pressure Gauge

Manifold Block (LZ□-MP× one piece)

JG A /JG B

Manifold JX

LC Standard Mounting

Coupler Switch PS

G-Thread Fitting

Fixture Base

Push Cylinder (DP) Application Example

DP-A□

DZ-MG□

Fixture Base

1024

WH Z -MD /LZ Y-MD /LZ -MS/LZ -M P

model

Manifold Block for WCA/WCE/WHA/WHE

C

A ±0.1

4-φR

K

6.3S

Manifold Block

Design No. (Revision Number)

Ny

C0.6

C0.6

H

Nx

B

K

Size (Refer to following table)

J

WHZ 048 0 - M D

φD + 0.3 0

Model No. Indication

2-O-ring

Z Surface

Ny

(Included) （mm）

Model No.

WHZ0600-MD

Corresponding Item Model Number

WCE0601

WCA0321

WCE1001

WCA0401

WCE1601

WCA0501

WCE2501

WCA0631

WCE4001

WHE0600

WHA0320

WHE1000

WHA0400

WHE1600

WHA0500

WHE2500

WHA0630

WHE4000

WHZ0400-MD

WHZ0500-MD

WHZ0630-MD

A

23

25

27

31

35

B

54

60

67

77

88.5

C

45

50

58

68

81

D

40

46

54

64

77

H

31.5

35

38

43

48

J

22.5

25

29

34

40.5 65

K

34

39

45

53

Nx

26

28

31

36

41

Ny

9

10

13

15

20

R

5.5

5.5

5.5

6.5

6.5

O-ring

1BP5

1BP7

1BP7

1BP7

1BP7

0.1

0.1

0.1

0.2

0.2

Mass Notes

WHZ0320-MD

kg

1. Material：A2017BE-T4 2. Mounting bolts are not provided. Prepare mounting bolts according to the mounting height using the A dimensions as a reference. 3. If thickness other than A is required, perform additional machining on surface Z. Please refer to the drawing.

Manifold Block for LKA/LKC/LKE/LHA/ LHC/LHE/LHS/LL

B

C ±0.1 6.3S

4-φK

J

Model No. Indication

φD + 0.3 0

Design No. (Revision Number)

A

J

C0.6

C0.6

G E

Size (Refer to following table)

F

LZY 048 0 - M D

2-O-ring

L Surface

H

(Included) （mm）

LZY0360-MD

Model No.

LZY0400-MD

LZY0480-MD

LZY0550-MD

LZY0650-MD

LZY0750-MD

LZY0900-MD

LZY1050-MD

LKA0360 / LKE0360 LKA0400 / LKC0400 LKA0480 / LKC0480 LKA0550 / LKC0550 LKA0650 / LKC0650

LKA0750

LKA0900

LKA1050

Corresponding Item LHA0360 / LHC0360 LKE0400 / LHA0400 LKE0480 / LHA0480 LKE0550 / LHA0550 LHA0650 / LHC0650 Model Number LHE0360 / LHS0360 LHC0400 / LHE0400 LHC0480 / LHE0480 LHC0550 / LHE0550 LHS0650

LHA0750

LHA0900

LHA1050

LHS0750

LHS0900

LHS1050

LL0360

LHS0400 / LL0400

LHS0480 / LL0480

LHS0550 / LL0550

LL0650

LL0750

LL0900

LL1050

A

49

54

61

69

81

92

107

122

B

40

45

51

60

70

80

95

110

C

20

20

27

30

32

37

45

50

D

36

40

48

55

65

75

90

105

E

29

31.5

35.5

39

46

52

59.5

67

F

20

22.5

25.5

30

35

40

47.5

55

G

23.5

26

30

33.5

39.5

45

52.5

60

H

16

18

22

24

30

32

37

45

J

31.4

34

40

47

55

63

75

88

K

4.5

5.5

5.5

6.8

6.8

9

11

14

O-ring

1BP5

1BP5

1BP5

1BP5

1BP7

1BP7

1BP7

1BP7

0.2

0.2

0.3

0.4

0.5

0.8

1.2

1.7

Mass Notes

kg

1. Material：S45C 2. Mounting bolts are not provided. Prepare mounting bolts according to the mounting height using the C dimensions as a reference. 3. If thickness other than C is required, perform additional machining on surface L. Please refer to the drawing.

1025

Manifold Block Model No. Indication/External Dimensions

Manifold Block for LM/LJ/LT/LG

B

4-φJ

H

High-Power Series

C±0.1 6.3S

Manifold Block Applicable Model/Application Examples

Pneumatic Series

Model No. Indication

LZ 048 0 - M S

F A

H

Design No. (Revision Number)

φD +0.3 0

Size (Refer to following table)

Hydraulic Series Valve / Coupler Hydraulic Unit

L E

C0.6

C0.6

Cautions / Others

O-ring (Included)

P Surface

M

Manual Operation Accessories

（mm） Model No.

LZ0360-MS

Corresponding Item Model Number

LT0360

LT0400

LT0480

LT0550

LM0360

LM0400

LM0480

LM0550

A

51.5

56.5

62

70

LZ0480-MS

LZ0550-MS

LZ0650-MS

LZ0750-MS

LZ0900-MS

LZ1050-MS

LT0650

LT0750

LG0900

LG1050

LM0650

LM0750

LJ0902

LJ1052

82

93

107

122

B

40

45

51

60

70

80

95

110

C

20

20

27

30

32

37

45

50

D

36

40

48

55

65

75

90

105

E

31.5

34

36.5

40

47

53

59.5

67

F

20

22.5

25.5

30

35

40

47.5

55

H

31.4

34

40

47

55

63

75

88

J

4.5

5.5

5.5

6.8

6.8

9

11

14

L

23.5

26

30

33.5

39.5

45

52.5

60

M

5

5

0

0

0

0

0

0

1BP5

1BP5

1BP5

1BP5

1BP7

1BP7

1BP7

1BP7

0.2

0.2

0.3

0.4

0.5

0.8

1.2

1.7

O-ring Mass Notes

LZ0400-MS

kg

Screw Locator VXF Manual Expansion Locating Pin VX

Manifold Block WHZ - MD L Z Y - MD L Z - MS L Z - MP T MZ- 1 MB T MZ- 2 MB DZ- M Manifold Block / Nut DZ- R

1. Material：S45C

DZ- C

2. Mounting bolts are not provided. Prepare mounting bolts according to the mounting height using the C dimensions as a reference.

DZ- P

3. If thickness other than C is required, perform additional machining on surface L. Please refer to the drawing.

DZ- B LZ- S

Manifold Block for LC/TC

LZ- SQ

C K

A±0.1

4-φR

T NZ- S T NZ- SQ

Model No. Indication

LZ 0 48 0 - M P

JB

φD +0.3 0

J Nx

B

K

Design No. (Revision Number)

C0.6

H

Yx

Size (Refer to following table)

Pressure Switch

C0.6

Pressure Gauge JG A /JG B

Manifold

Yy

Ny

P Surface （mm）

Model No.

LZ0400-MP

LZ0480-MP

LZ0550-MP

LZ0650-MP

LZ0750-MP

LZ0900-MP

Corresponding Item Model Number

LC0402

LC0482

LC0552

LC0652

LC0752

LC0902

TC0402

TC0482

TC0552

TC0652

TC0752

A

20

27

30

32

37

45 107

B

56.5

62

70

82

93

45

51

60

70

80

95

D

40

48

55

65

75

90

H

34

36.5

40

47

53

59.5

J

22.5

25.5

30

35

40

47.5

K

34

40

47

55

63

75

Nx

26

30

33.5

39.5

45

52.5

Ny

5

0

0

0

0

0

R

5.5

5.5

6.8

6.8

9

11 50

Yx

25

28

31

37

42.5

Yy

8

11

13

14

15

15

O-ring

1BP5

1BP5

1BP5

1BP7

1BP7

1BP7

0.2

0.3

0.4

0.5

0.8

1.2

kg

JX

Coupler Switch PS

G-Thread Fitting

C

Mass Notes

2-O-ring (Included)

1. Material：S45C 2. Mounting bolts are not provided. Prepare mounting bolts according to the mounting height using the A dimensions as a reference. 3. If thickness other than A is required, perform additional machining on surface P. Please refer to the drawing.

1026

Company Profile

Sales Offices Sales Offices across the World FAX. +81-78-991-8787

Japan

TEL. +81-78-991-5162

Overseas Sales

KOSMEK LTD. 1-5, 2-chome, Murotani, Nishi-ku, Kobe-city, Hyogo, Japan 651-2241

USA

TEL. +1-630-241-3465

KOSMEK（USA）LTD.

1441 Branding Avenue, Suite 110, Downers Grove, IL 60515 USA

China

TEL.+86-21-54253000

KOSMEK（CHINA）LTD. 考世美(上海)貿易有限公司

〒651-2241

兵庫県神戸市西区室谷2丁目1番5号

FAX. +1-630-241-3834

FAX.+86-21-54253709

21/F, Orient International Technology Building, No.58, Xiangchen Rd, Pudong Shanghai 200122., P.R.China 中国上海市浦东新区向城路58号东方国际科技大厦21F室 200122

FAX. +66-2-715-3453

Thailand

TEL. +66-2-715-3450

Thailand Representative Office

67 Soi 58, RAMA 9 Rd., Suanluang, Suanluang, Bangkok 10250, Thailand

Taiwan

TEL. +886-2-82261860

Full Life Trading Co., Ltd.

16F-4, No.2, Jian Ba Rd., Zhonghe District, New Taipei City Taiwan 23511

(Taiwan Exclusive Distributor)

FAX. +886-2-82261890

盈生貿易有限公司

台湾新北市中和區建八路2號 16F- 4（遠東世紀廣場）

Philippines

(Philippines Exclusive Distributor)

TEL.+63-2-310-7286

G.E.T. Inc, Phil.

Victoria Wave Special Economic Zone Mt. Apo Building, Brgy. 186, North Caloocan City, Metro Manila, Philippines 1427

Europe

(Europe Exclusive Distributor)

TEL. +43-463-287587-10 FAX. +43-463-287587-20

KOS-MECH GmbH

Schleppeplatz 2 9020 Klagenfurt Austria

Indonesia

TEL. +62-21-5818632

(Indonesia Exclusive Distributor)

FAX. +63-2-310-7286

FAX. +62-21-5814857

P.T PANDU HYDRO PNEUMATICS Ruko Green Garden Blok Z-Ⅱ No.51 Rt.005 Rw.008 Kedoya Utara-Kebon Jeruk Jakarta Barat 11520 Indonesia

Sales Offices in Japan Head Office Osaka Sales Office Overseas Sales

Tokyo Sales Office

Nagoya Sales Office

Fukuoka Sales Office 1061

TEL.078-991-5115 〒651-2241

兵庫県神戸市西区室谷2丁目1番5号

TEL.048-652-8839 〒331-0815

FAX.0566-74-8808

愛知県安城市美園町2丁目10番地1

TEL.092-433-0424 〒812-0006

FAX.048-652-8828

埼玉県さいたま市北区大成町4丁目81番地

TEL.0566-74-8778 〒446-0076

FAX.078-991-8787

FAX.092-433-0426

福岡県福岡市博多区上牟田1丁目8-10-101

Global Network Overseas Affiliates and Sales Offices Distributors

Europe U.S.A. Asia

Mexico

Brazil Australia

Asia Detailed Map

Korea Japan

China Taiwan

India Thailand

Philippines

Malaysia Singapore

Indonesia

● FOR FURTHER INFORMATION ON UNLISTED SPECIFICATIONS AND SIZES, PLEASE CALL US. ● SPECIFICATIONS IN THIS CATALOG ARE SUBJECT TO CHANGE WITHOUT NOTICE.

JQA-QMA10823

KOSMEK HEAD OFFICE