Counter Height Storage Cabinets – 9000 Series Assembly Instructions

Thank you for selecting Salsbury’s counter height storage cabinet. We are confident that the quality and construction of the cabinet will prove to be a good investment. Individual job conditions will dictate whether the storage cabinets should be anchored to the wall, the floor, or both and the type of fasteners that are to be used to do so. General Notes 1. These instructions represent the assembly of the Salsbury standard 18” deep counter height storage cabinets. Parts and quantities of fasteners used will be different than for the other standard cabinets. 2. All connections using screws should initially be just finger tight. Square the cabinet assembly before firmly tightening all connections. STEP 1 Locate the left and right back panels and lay them down on a flat surface with the flanges facing up. Place the left back panel on top of the right back panel and slide the latches in place to secure together. The end with four (4) latches along the edge is the bottom end. See Figure 1. Figure 1

Place left back panel on top of right back panel

Phone: 1-800-562-5377

Slide latches in place to secure back panels together

SALSBURY INDUSTRIES 1010 East 62nd Street, Los Angeles, CA 90001-1598 Int’l Phone: 323-846-6700 Fax: 1-800-562-5399 www.lockers.com [email protected]

Bottom of back panel has four (4) latches along edge

Int’l Fax: 323-846-6800

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability. Copyright © 2016 Salsbury Industries. All rights reserved. (6/28/2016)

Page 1 of 5

STEP 2 Locate the right side panel. Attach the right side panel to the back panel by inserting the two (2) latches on the side panel through the slots on the back panel. See Figure 2.

Figure 2

Right side panel

Insert right side panel latches through slots on back panel; slide to secure

Bottom of back panel

STEP 3 Locate the left side panel and repeat step 2. See Figure 3.

Figure 3

Left side panel

Bottom of back panel Insert left side panel latches through slots on back panel; slide to secure

Phone: 1-800-562-5377

SALSBURY INDUSTRIES 1010 East 62nd Street, Los Angeles, CA 90001-1598 Int’l Phone: 323-846-6700 Fax: 1-800-562-5399 www.lockers.com [email protected]

Int’l Fax: 323-846-6800

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability. Copyright © 2016 Salsbury Industries. All rights reserved. (6/28/2016)

Page 2 of 5

STEP 4 Locate and secure the top panel by placing the flange on the back of the top panel behind the back panel. Simultaneously inserting the top panel latches through the slots on both side panels. Attach top panel to back panel and side panels with screws and nuts (provided) with nuts on the inside of the unit. See Figure 4.

Figure 4

Latches on top panel

Place flange on back of top panel behind the back panel

Insert top panel latches through slots on both side panels to secure

Top panel flange

Attach top panel to back panel and side panels with screws and nuts (provided)

Phone: 1-800-562-5377

SALSBURY INDUSTRIES 1010 East 62nd Street, Los Angeles, CA 90001-1598 Int’l Phone: 323-846-6700 Fax: 1-800-562-5399 www.lockers.com [email protected]

Int’l Fax: 323-846-6800

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability. Copyright © 2016 Salsbury Industries. All rights reserved. (6/28/2016)

Page 3 of 5

STEP 5 Locate the bottom panel and insert the bottom panel’s back flange into the latches located on the back panel. See Figure 5A. Attach bottom panel to back panel and side panels with screws and nuts (provided) with nuts on the inside of the unit. See Figure 5B.

Figure 5A

Slide bottom panel down to secure it to back panel latches

Figure 5B

Attach top panel to back panel and side panels with screws and nuts (provided)

STEP 6 Place the first adjustable shelf into the unit by inserting the shelf panel into the desired shelf notch height located on the back panel. Then insert shelf clips into the front interior flanges of both side panels to support the front of the shelf. Repeat this process for the remaining shelves. See Figure 6.

Figure 6 Insert back of shelf panel into desired shelf notches

Phone: 1-800-562-5377

Insert shelf clips into front interior flanges of side panels

SALSBURY INDUSTRIES 1010 East 62nd Street, Los Angeles, CA 90001-1598 Int’l Phone: 323-846-6700 Fax: 1-800-562-5399 www.lockers.com [email protected]

Rest front of shelf onto shelf clips for support

Int’l Fax: 323-846-6800

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability. Copyright © 2016 Salsbury Industries. All rights reserved. (6/28/2016)

Page 4 of 5

STEP 7 Position left door in place and insert hinge pins into top and bottom door hinges. Repeat this process for the right door. See Figure 7.

Figure 7

Insert hinge pin until top is flush with top of door hinge

STEP 8 Ensure that guides are fully inserted and locked in place. Mount handle on right door with two (2) screws and lockwashers. Insert lock bar guides into slots on top and bottom of right door. Place latch onto the door handle bolt. See Figure 8.

Figure 8 Insert lock bar guides on top and bottom of locking door

Place latch onto door handle bolt

Mount handle on right door with provided hardware

STEP 9 Rotate latch to position shown below. Mount lock bars on latch as shown below. Do not fasten latch to handle yet. Rotate handle to open (unlatched position or horizontal) position. Insert lock bars into plastic guides while aligning square hole in latch with square threaded shoulder on handle. Install lock nut on threaded shank of handle. Check that handle, latch, and lock bars operate smoothly and effectively. See Figure 9. This completes the assembly of your storage cabinet.

Figure 9 Rotate latch to this position

Insert lock bars through guides on top and bottom of door

Phone: 1-800-562-5377

Install lock nut to secure locking mechanism

SALSBURY INDUSTRIES 1010 East 62nd Street, Los Angeles, CA 90001-1598 Int’l Phone: 323-846-6700 Fax: 1-800-562-5399 www.lockers.com [email protected]

Your counter height storage cabinet unit is complete.

Int’l Fax: 323-846-6800

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability. Copyright © 2016 Salsbury Industries. All rights reserved. (6/28/2016)

Page 5 of 5