Coriolis Mass Flow Meter
CMM
Coriolis Mass Flow Meter CMM
Construction
Function The Coriolis Mass Flow meter CMM contains oscilating measuring tubes which make use of the Coriolis force effect. The mass flow entering through the inlet of the flow meter is distributed by the flow-distributor to the measuring tubes bended parallely and symmetrically. The measured medium after flowing through the measuring tubes is collected in the meter body and is leaving the meter through the outlet. Due to an electromagnetic oscillating coil the symmetrical constructed pair of measuring tube is oscillating continuously and symmetrically at its momentary resonance frequency. Two sensor coils are fixed at the pipes symmetrically, sensing the symmetry of the oscillation. In flowless condition the electric signal of the two coils are sine wave signals identical in amplitude and in phase. In case a mass flow is started through the pipes, the symmetry of the oscillation is disturbed. Due to this sine wave signal of the sensor at one side is shifted in phase from the sine sine wave of the sensor at the other side. The value of the phase shift is directly proportional to the mass flow.
2
With the signal processing unit C-Mass the signals of CMM are received and processed. As output signals frequency, current output or serial interface are available. The sensor can be operated in hazardous areas. In this case a special zener barrier unit has to be inserted between the electronic unit and the mass flow sensor. The protection mode of the measuring system is: II (2) G [Ex ib] IIB [05 ATEX 034)
KRACHT GmbH · Gewerbestr. 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 · web www.kracht.eu · mail
[email protected]
Coriolis Mass Flow Meter CMM
Technical Data
General Characteristics Ambient temperature
-- 50 °C … + 70 °C (-- 58 °F … + 158 °F)
Medium temperaturer
-- 50 °C … + 150 °C (-- 58 °F … + 302 °F) with remote electronic unit -- 50 °C … + 80 °C (-- 58 °F … + 176 °F) with compact electronic unit -- 20 °C … (-- 4 °F … ) according to Ex classification
Material
Stainless steel 1.4541 (316 L)
Degree of protection
IP 65
Electrical Characteristics Output signals
Frequency (max. 10 kHz) Current (max. 20 mA) Serial interface (RS 232 or RS 485/422 with MODBUS RTU printout)
Operating voltage
19… 29 VDC (max. 150 mA)
Ambient temperature
-- 50 °C … + 70 °C (-- 58 °F … + 158 °F)
Degree of protection
IP 65
Flow rate Type CMM CMM CMM CMM CMM CMM CMM CMM CMM
0.15 0.3 0.5 1 3 6 14 40 80
Accuracy Max. flow rate [kg/min]
The maximum error of the measurement calculated as follows:
2.5 5.0 8.5 17.0 50.0 100.0 233.0 667.0 1334.0
h = ± 0.2 ± 5/q (%) h q Q Qmax
by: q = Q / Qmax x 100 (%)
maximal error of measurement related to the measured value (%) flow rate (%) mass flow to be measurement (kg/h) maximal mass flow (kg/h)
The maximum final value error is ± 0.05 %
KRACHT GmbH · Gewerbestr. 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 · web www.kracht.eu · mail
[email protected]
3
Coriolis Mass Flow Meter CMM
Type Key Ordering example
CMM
0.15
N
S
F
016
J
N EX protection N no Z with Zener barrier unit
Electrical connection J junction box C compact electronic Pressure rating 016 025 040 063 100 160 250 320 400 Connection type F flanged R NPT E ERMETO
16 25 40 63 100 160 250 320 400
bar bar bar bar bar bar bar bar bar
Material S stainless steel X special Pressure N normal H high Nominal size 0.15 0.3 0.5 1 max. flow rate (t/h) 3 6 14 40 80 Product code
4
KRACHT GmbH · Gewerbestr. 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 · web www.kracht.eu · mail
[email protected]
Coriolis Mass Flow Meter CMM
Dimensions
CMM – 0.15 … 1 – N –
CMM – – N 0.15 … 0.3
X
CMM – 3 … 80 – N –
Y
Z
P
Q
mm 360
220
23
W threaded
102
196
Max. pressure flanged
bar
NPT
1⁄ 2
DN15
250
1⁄ 2
DN15
250
1
400
280
23
102
196
NPT
3
494
324
23
102
230
NPT 1⁄2
DN15
160
6
560
384
28
128
286
NPT 3⁄4
DN 25
160
14
680
456
32
144
410
NPT 1
DN 25
160
40
820
580
40
175
465
NPT 11⁄2
DN 40
100
80
748
748
100
224
578
–
DN 80
40
Y
Z
P
Q
CMM – 0.15 … 40 – H –
CMM – – H
X
mm
W
Max. pressure
ERMETO
flanged
bar
0.15 … 0.3
112
166
128
80
142
M 16 x 1.5
–
400
1
112
204
159
80
178
M 20 x 1.5
–
400
3
122
294
202
98
221
M 20 x 1.5
–
400
6
164
364
241
112
265
M 27 x 2,5
–
400
14
318
530
334
168
426
–
DN 40
250
40
336
560
380
204
476
–
DN 50
160
KRACHT GmbH · Gewerbestr. 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 · web www.kracht.eu · mail
[email protected]
5
Product Portfolio Transfer Pumps
Flow Measurement
Transfer pumps for lubricating oil supply equipment, low pressure filling and feed systems, dosing and mixing systems.
Gear and turbine flow meters and electronics for volume and flow metering technology in hydraulics, processing and laquering technology.
Mobile Hydraulics
Industrial Hydraulics / Test Bench Construction
Single and multistage high pressure gear pumps, hydraulic motors and valves for construction machinery, vehicle-mounted machines.
Cetop directional control and proportional valves, hydraulic cylinders, pressure, quantity and stop valves for pipe and slab construction, hydraulic accessories for industrial hydraulics (mobile and stationary use). Technology Test benches / Fluid Test benches.
CMM / GB / 06.07
KRACHT GmbH · Gewerbestraße 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 mail
[email protected] · web www.kracht.eu