CON-STAB ANODELESS METER RISERS

WAL-RICH CORPORATION SINCE 1950 Con-Stab ID Seal® Fittings have been sold in the gas, plumbing, and propane markets since 1990. ConStab® fittings are...
Author: Marjory Casey
4 downloads 0 Views 312KB Size
WAL-RICH CORPORATION

SINCE 1950 Con-Stab ID Seal® Fittings have been sold in the gas, plumbing, and propane markets since 1990. ConStab® fittings are IAPMO, CSA, & ICC approved.

for: Pool Heaters

for: Gas Grills

for: Patio Hearths

for: Emergency

& Lighting

Generators

CON-STAB® ANODELESS METER RISERS

- Fusion-bonded epoxy coating - Anodeless and corrosion resistant - Patented “ID-Seal” fitting (inside chamfer)

Always Match Pipe Size & SDR

W-R

Size

2886036 2886004 2886008 2886040 2886012 2886013 2886016 2886020

1/2” CTS 3/4” IPS 1” IPS 1” CTS 1 1/4” IPS 1 1/4” IPS 1 1/2” IPS 2” IPS

Wall (CTS) or SDR

.090 SDR-11 SDR-11 .099/.101 SDR-10 SDR-11 SDR-11 SDR-11

You must use a Continental Chamfer Tool on a Continental Fitting!

POLY-END ANODELESS METER RISERS - Fusion-bonded epoxy coating - Anodeless and corrosion resistant - Plain PE end can be used with compression & “stab” fittings - 3” must be used with Dresser Style 711 couplings. See page 6. 2886070

CALL (800) 221-1157

·

W-R

Size

2886002 2886006 2886030 2886010 2886011 2886014 2886018 2886070

3/4” IPS 1” IPS 1” CTS 1 1/4” IPS 1 1/4” IPS 1 1/2” IPS 2” IPS 3” IPS

www.wal-rich.com 21

·

Wall (CTS) or SDR

SDR-11 SDR-11 .099/.101 SDR-10 SDR-11 SDR-11 SDR-11 SDR-11.5

FAX (516) 277-2177

WAL-RICH CORPORATION

SINCE 1950 Con-Stab ID Seal® Fittings have been sold in the gas, plumbing, and propane markets since 1990. Con-Stab® fittings are IAPMO, CSA, & ICC approved. From NFPA 54 Section 3.3.5

“An anodeless riser is an assembly of steel-cased plastic pipe used to make the transition between plastic piping underground and metal piping aboveground.”

Inside Seal!

(O-RING)

Plastic Pipe runs inside the riser.

Con-Stab®’s patented “ID-Seal” is formed on the INSIDE of the pipe--where the surface is the smoothest.

Corrosion-resistant fusion-bonded epoxy coating

Therefore you must chamfer the INSIDE of your pipe with a Continental® Chamfer tool. CON-STAB® COUPLINGS

Always Match Pipe Size & SDR

Gas

CON-STAB® ELBOWS Always Match Pipe Size & SDR

Gas

CON-STAB® TEES Always Match Pipe Size & SDR

CALL (800) 221-1157

·

Gas

W-R

Size

2881000 2881002 2881004 2881020 2881006 2881007 2881008 2881010

1/2” CTS 3/4” IPS 1” IPS 1” CTS 1 1/4” IPS 1 1/4” IPS 1 1/2” IPS 2” IPS

W-R

Size

2882000 2882002 2882004 2882020 2882006 2882007 2882008 2882010

1/2” CTS 3/4” IPS 1” IPS 1” CTS 1 1/4” IPS 1 1/4” IPS 1 1/2” IPS 2” IPS

W-R

Size

2883000 2883002 2883004 2883020 2883006 2883007 2883008 2883010

1/2” CTS 3/4” IPS 1” IPS 1” CTS 1 1/4” IPS 1 1/4” IPS 1 1/2” IPS 2” IPS

www.wal-rich.com 22

·

Wall (CTS) or SDR

.090 SDR-11 SDR-11 .099/.101 SDR-10 SDR-11 SDR-11 SDR-11 Wall (CTS) or SDR

.090 SDR-11 SDR-11 .099/.101 SDR-10 SDR-11 SDR-11 SDR-11 Wall (CTS) or SDR

.090 SDR-11 SDR-11 .099/.101 SDR-10 SDR-11 SDR-11 SDR-11

FAX (516) 277-2177

WAL-RICH CORPORATION

SINCE 1950 Con-Stab ID Seal® Fittings have been sold in the gas, plumbing, and propane markets since 1990. ConStab® fittings are IAPMO, CSA, & ICC approved.

CON-STAB® MALE ADAPTERS 4”

18” Overall

Always Match Pipe Size & SDR Gas

POLY PLAIN-END MALE ADAPTERS

Always Match Pipe Size & SDR Gas

CON-STAB® CHAMFER TOOL

Always Match Pipe Size & SDR

LOOK FOR THE “C” You must use a Continental Chamfer Tool on a Continental Fitting!

CALL (800) 221-1157

W-R

Size

Wall (CTS) or SDR

2885000 2885002 2885004 2885020 2885006 2885007 2885008 2885010

1/2” CTS 3/4” IPS 1” IPS 1” CTS 1 1/4” IPS 1 1/4” IPS 1 1/2” IPS 2” IPS

.090 SDR-11 SDR-11 .099/.101 SDR-10 SDR-11 SDR-11 SDR-11

- Standard sizes with 4” long steel MIP stub.

W-R

Size

2885050 2885052 2885070 2885054 2885055 2885056 2885058

3/4” 1” 1” 1 1/4” 1 1/4” 1 1/2” 2”

Wall (CTS) or SDR

IPS IPS CTS IPS IPS IPS IPS

SDR-11 SDR-11 .099/.101 SDR-10 SDR-11 SDR-11 SDR-11

- Standard sizes with 4” long steel MIP stub. - Plain End can be used with stab couplings, compression couplings, and fusion fittings.

W-R

Size

2888020 2888014 2888016 2888022 2888006 2888007 2888008 2888010

1/2” CTS 3/4” IPS 1” IPS 1” CTS 1 1/4” IPS 1 1/4” IPS 1 1/2” IPS 2” IPS

Wall (CTS) or SDR

.090 SDR-11 SDR-11 .099/.101 SDR-10 SDR-11 SDR-11 SDR-11

- Follow the Arrow! Turn the tool in the direction of the arrow printed on the tool for a clean, even chamfer (bevel) on the inside of the pipe.

·

www.wal-rich.com 23

·

FAX (516) 277-2177

WAL-RICH CORPORATION

SINCE 1950 Con-Stab ID Seal® Fittings have been sold in the gas, plumbing, and propane markets since 1990. ConStab® fittings are IAPMO, CSA, & ICC approved.

CON-STAB® x COPPER TRANSITION FITTING Always Match Pipe Size & SDR

W-R

Con-Stab®

Copper Tube

2884002 3/4” SDR 11

1/2” Flare

- Con-Stab® x Flare connection for copper tubing

Gas W-R

IPS X IPS REDUCERS

CON-STAB® REDUCING COUPLINGS

2891030 1”

IPS X IPS

2891049 1 1/4” SDR10 x 3/4” SDR11 2891021 1 1/4” SDR10 x 1” SDR11 2891050 1 1/4” SDR11 x 3/4” SDR11 2891022 1 1/4” SDR11 x 1” SDR11

Always Match Pipe Size & SDR Gas

2891010 2891012 2891013 2891014 2891002 2891004 2891005 2891006 2891008 W-R

CTS X IPS Always Match Pipe Size & SDR Gas

CON-STAB® 1 1/4” SDR-10 x SDR-11 ADAPTER SDR-11

SDR11 x 3/4” SDR11

1 1/2” SDR11 x 3/4” SDR11 1 1/2” SDR11 x 1” SDR11 1 1/2” SDR11 x 1 1/4”SDR10 1 1/2” SDR11 x 1 1/4”SDR11 2” 2” 2” 2” 2”

SDR11 x 3/4” SDR11 SDR11 x 1” SDR11 SDR11 x 1 1/4”SDR10 SDR11 x 1 1/4”SDR11 SDR11 x 1 1/2”SDR11

CTS X IPS REDUCERS

2890040 1/2” 2890042 1/2”

CTS x 3/4” SDR11 CTS x 1” SDR11

2890002 1” 2890004 1”

CTS x 3/4” SDR11 CTS x 1” SDR11

W-R

Con-Stab® A

2890008 1 1/4” IPS x SDR-10

Con-Stab® B

1 1/4” IPS SDR-11

“THE MIRACLE FITTING” SDR-10

CALL (800) 221-1157

·

www.wal-rich.com 24

·

FAX (516) 277-2177

WAL-RICH CORPORATION

SINCE 1950 Con-Stab ID Seal® Fittings have been sold in the gas, plumbing, and propane markets since 1990. ConStab® fittings are IAPMO, CSA, & ICC approved.

CON-STAB® REDUCING TEES

W-R

RUN

2883070

1”

BRANCH

SDR11 x 3/4” SDR11

2883061 1 1/4” SDR10 x 3/4” SDR11 2883063 1 1/4” SDR10 x 1” SDR11 Always Match Pipe Size & SDR

2883062 1 1/4” SDR11 x 3/4” SDR11 2883064 1 1/4” SDR11 x 1” SDR11 Gas

2883080 2883082 2883083 2883084 2883050 2883052 2883053 2883054 2883056

CON-STAB® SADDLE PUNCH TEES

Always Match Pipe Size & SDR Gas

CALL (800) 221-1157

·

2” 2” 2” 2” 2”

SDR11 x SDR11 x SDR11 x SDR11 x SDR11 x

3/4” SDR11 1” SDR11 1 1/4” SDR10 1 1/4” SDR11 1 1/2” SDR11

W-R

MAIN

2893090 2893092

1 1/4” 1 1/4”

3/4” SDR-11 1” SDR-11

2896002 2896006

1 1/2” 1 1/2”

3/4” SDR-11 1” SDR-11

2894002 2894004 2894006

2” 2” 2”

3/4” SDR-11 1” SDR-11 1 1/4” SDR-11

2894502 2894504 2894506 2894508

3” 3” 3” 3”

3/4” 1” 1 1/4” 2”

www.wal-rich.com 25

1 1/2” SDR11 x 3/4” SDR11 1 1/2” SDR11 x 1” SDR11 1 1/2” SDR11 x 1 1/4” SDR10 1 1/2” SDR11 x 1 1/4” SDR11

·

OUTLET

SDR-11 SDR-11 SDR-11 SDR-11

FAX (516) 277-2177

WAL-RICH CORPORATION

SINCE 1950 Con-Stab ID Seal® Fittings have been sold in the gas, plumbing, and propane markets since 1990. ConStab® fittings are IAPMO, CSA, & ICC approved.

CON-STAB® END CAPS Always Match Pipe Size & SDR

Gas

CONFLEX® FLEX RISERS FOR PROPANE B

A

Gas

W-R

Size

2892000 2892002 2892004 2892020 2892006 2892007 2892008 2892010

1/2” CTS 3/4” IPS 1” IPS 1” CTS 1 1/4” IPS 1 1/4” IPS 1 1/2” IPS 2” IPS

Step 3.

.090 SDR-11 SDR-11 .099/.101 SDR-10 SDR-11 SDR-11 SDR-11

Continental “Con-Flex®” risers are flexible casings that protect yellow polyethylene pipe aboveground. Con-flex® risers consist of corrugated stainless steel flex hose, with a durable UV & weather-resistant outer sleeve. Conforms to NFPA 54 & 58 for LPG systems. W-R

Step 1.

Wall (CTS) or SDR

Description

Length

2887002 1/2” COP x 1/2” MIP 2887004 1/2” COP x 1/2” MIP

36” 84”

2887020 3/4” IPS x 3/4” MIP

36”

2887030 1” IPS x 1” MIP

36”

Instructions: 1. Disassemble the adapter coupling (B). 2. Feed the polyethylene pipe through the sleeve from the moisture seal (A) to the adapter coupling (B) 3. Assemble the adapter coupling by sliding the gasket over the tubing, and then pushing the tubing onto the insert. Tighten the compression nut until it bottoms out.

POLYETHYLENE GAS BALL VALVES Always Match Pipe Size & SDR

W-R

Size

2893102 2893104 2893106 2893108 2893110

3/4” 1” 1 1/4” 1 1/2” 2”

Wall (CTS) or SDR

IPS IPS IPS IPS IPS

SDR-11 SDR-11 SDR-11 SDR-11 SDR-11

Gas

CALL (800) 221-1157

·

www.wal-rich.com 26

·

FAX (516) 277-2177

WAL-RICH CORPORATION Match Pipe & SDR

Step 2:

Chamfer Inside of Pipe

BE SURE TO MATCH PIPE SIZE & SDR*

BEFORE

AFTER

Pipe, Fittings, and Chamfer Tool must be the same!

SQUARE-CUT

Mark Stab Depth

○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○

1.

Stab & Check

Stab the pipe completely into the fitting, so that the “stab marker” is within 1/8” from the entrance of the fitting.

1. Line up the end of the yellow pipe with the hub of the fitting. 1/8”

2. Mark a line on the pipe to approximate the end of the fitting. 3. Goal: The reason to mark the stab depth is to ensure that the pipe is sealed by both o-rings!

Test your chamfer by pushing the pipe over the test gauge. If the pipe is chamferred properly, it should fit over the test gauge with minimum effort.

STAB PIPE INTO FITTING

2.

“Hub”

The “coupon” is the piece of yellow poly that is shaved off during the act of chamferring.

Test Gauge

Step 4:

MARK THE STAB DEPTH!

CHAMFERRED

Follow the arrows printed on the label. Only 3-5 turns necessary for a good chamfer!

*“SDR” stands for “Standard Dimension Ratio”. It is a designation of a pipe’s pressure rating. SDR is the ratio of Pipe Diameter to Wall Thickness.

Step 3:

CHAMFER INSIDE

Step 1:

SINCE 1950

Once the pipe has been stabbed, it cannot be removed.

(O-RING)

LOOK FOR You must use a Continental Chamfer Tool THE “C” on a Continental Fitting! CALL (800) 221-1157

·

www.wal-rich.com 27

·

FAX (516) 277-2177

WAL-RICH CORPORATION

SINCE 1950

YELLOW PLASTIC GAS PIPE

YELLOW “MEDIUM DENSITY” (PE2406) PE GAS PIPE T 50 FOO NEW! IENCE COILS N CONVE

Always Match Pipe Size & SDR

Conforms to ASTM D-2513 Gas

For several years, the gas utility and distribution market has used plastic gas pipe for its ease-of-use, corrosion resistance, and cost effectiveness. NFPA 54 provides for the use of plastic piping within it’s code for outdoor, underground use only at a minimum burial depth of 18” , using yellow 14g tracer wire for location purposes.

Call us today for: - Free promotional materials - One-on-One sales training - Sizing/Technical assistance

W-R

Size

Wall (CTS) or SDR

Length

2880004 1/2” CTS

.090

500’

2880011 3/4” IPS 2880012 3/4” IPS 2880016 3/4” IPS

SDR-11 SDR-11 SDR-11

50’ 150’ 500’

2880020 1” CTS 2880021 1” CTS

.099/.101 .099/.101

150’ 500’

2880025 1” IPS 2880022 1” IPS 2880026 1” IPS

SDR-11 SDR-11 SDR-11

50’ 150’ 500’

2880029 1 1/4” IPS SDR-10 2880030 1 1/4” IPS SDR-10

50’ 150’

2880031 1 1/4” IPS SDR-11 2880032 1 1/4” IPS SDR-11 2880036 1 1/4” IPS SDR-11

50’ 150’ 500’ (*)

2880041 1 1/2” IPS SDR-11 2880042 1 1/2” IPS SDR-11 2880046 1 1/2” IPS SDR-11

50’ 150’ 500’ (*)

2880051 2” IPS 2880052 2” IPS 2880056 2” IPS

SDR-11 SDR-11 SDR-11

50’ 100’ 500’ (*)

2880062 3” IPS

SDR-11.5

100’ (*)

(*) Call for availability

CALL (800) 221-1157

·

www.wal-rich.com 28

·

FAX (516) 277-2177

WAL-RICH CORPORATION

SINCE 1950

LOW PRESSURE < 2PSI Spec. Gravity: .60

Pressure Drop: 1.0 in w.c.

Length 1/2 IPS 3/4 IPS 1 IPS 1 1/4 IPS 1 1/2 IPS 2 IPS SDR-11 SDR-11 (feet) SDR-9.3 SDR-11 SDR-11 SDR-10

10 20 30 40 50 60 70 80 90 100 125 150 175 200 250 300 350 400 450 500

201 138 111 95 84 76 70 65 61 58 51 46 43 40 35 32 29 27 26 24

403 277 222 190 169 153 140 131 123 116 103 93 86 80 71 64 59 55 51 48

Length 1/2 IPS 3/4 IPS (feet) SDR-9.3 SDR-11

10 20 30 40 50 60 70 80 90 100 125 150 175 200 250 300 350 400 450 500

726 1260 1900 3410 499 865 1310 2350 401 695 1050 1880 343 594 898 1610 304 527 796 1430 276 477 721 1300 254 439 663 1190 236 409 617 1110 221 383 579 1040 209 362 547 983 185 321 485 871 168 291 439 789 154 268 404 726 144 249 376 675 127 221 333 598 115 200 302 542 106 184 278 499 99 171 258 464 93 160 242 435 411 88 152 229

LOW PRESSURE: 11 IN. W.C.

1860 1280 1030 878 778 705 649 603 566 535 474 429 395 368 326 295 272 253 237 224

1 1/4 IPS

1 1/2 IPS

2 IPS

SDR-11

SDR-10

SDR-11

SDR-11

17600 12100 9690 8300 7350 6660 6130 5700 5350 5050 4480 4060 3730 3470 3080 2790 2570 2390 2240 2120

31600 21700 17400 14900 13200 12000 11000 10200 9610 9080 8050 7290 6710 6240 5530 5010 4610 4290 4020 3800

6710 11600 4610 7990 3710 6420 3170 5490 2810 4870 2550 4410 2340 4060 2180 3780 2050 3540 1930 3350 1710 2970 1550 2690 1430 2470 1330 2300 1180 2040 1070 1850 981 1700 913 1580 856 1480 809 1400

3720 2560 2050 1760 1560 1410 1300 1210 1130 1070 949 860 791 736 652 591 544 506 475 448

HIGH PRESSURE = 2PSI Pressure Drop: 1.0 in w.c.

Length 1/2 IPS 3/4 IPS 1 IPS 1 1/4 IPS 1 1/2 IPS 2 IPS SDR-11 SDR-11 (feet) SDR-9.3 SDR-11 SDR-11 SDR-10

Length 1/2 IPS 3/4 IPS (feet) SDR-9.3 SDR-11

340 233 187 160 142 129 119 110 103 98 87 78 72 67 60 54 50 46 43 41

680 468 375 321 285 258 237 221 207 196 173 157 145 135 119 108 99 92 87 82

1230 844 677 580 514 466 428 398 374 353 313 284 261 243 215 195 179 167 157 148

2130 1460 1170 1000 890 807 742 690 648 612 542 491 452 420 373 338 311 289 271 256

3210 2210 1770 1520 1340 1220 1120 1040 978 924 819 742 683 635 563 510 469 436 409 387

10 20 30 40 50 60 70 80 90 100 125 150 175 200 250 300 350 400 450 500

5770 3970 3180 2730 2420 2190 2010 1870 1760 1660 1470 1330 1230 1140 1010 916 843 784 736 695

3130 2150 1730 1480 1310 1190 1090 1010 952 899 797 722 664 618 548 496 457 425 399 377

Spec. Gravity: 1.50

1 IPS

1 1/4 IPS

1 1/2 IPS

2 IPS

SDR-11

SDR-10

SDR-11

SDR-11

6260 11300 19600 29500 4300 7760 13400 20300 3450 6230 10800 16300 2960 5330 9240 14000 2620 4730 8190 12400 2370 4280 7420 11200 2180 3940 6830 10300 2030 3670 6350 9590 1910 3440 5960 9000 1800 3250 5630 8500 1600 2880 4990 7530 1450 2610 4520 6830 1330 2400 4160 6280 1240 2230 3870 5840 1100 1980 3430 5180 3110 4690 994 1790 914 1650 2860 4320 851 1530 2660 4020 798 1440 2500 3770 754 1360 2360 3560

* Values listed are in cubic feet/meter (cfm). To calculate BTU, multiply by 1000.

* Values listed are in cubic feet/meter (cfm). To calculate BTU, multiply by 1000.

** Source: NFPA 54-2012 Table 6.2 (s)

** Source: NFPA 54-2012 Table 6.2 (s)

53100 36500 29300 25100 22200 20100 18500 17200 16200 15300 13500 12300 11300 10500 9300 8430 7760 7220 6770 6390

PROPANE

Pressure Drop: .5 in w.c. Spec. Gravity: 1.50

10 20 30 40 50 60 70 80 90 100 125 150 175 200 250 300 350 400 450 500

Spec. Gravity: .60

1 IPS

NATURAL GAS

Pressure Drop: .5 in w.c.

HIGH PRESSURE = 2PSI

*Reproduced with permission from NFPA 54, National Fuel Gas Code, Copyright 2012. This reprinted material is not the complete and official position of the NFPA on the referenced subject, which is represented only by the standard in its entirety. Please consult your NFPA 54/ICC Fuel Gas codebook and appliance’s technical literature for more detailed sizing and installation instructions.

CALL (800) 221-1157

·

www.wal-rich.com 29

·

FAX (516) 277-2177

WAL-RICH CORPORATION

SINCE 1950

FIRST-STAGE TO SECOND STAGE

30 40 50 60 70 80 90 100 125 150 175 200 250 300 350 400 450 500

4292 3673 3256 2950 2714 2525 2369 2238 1983 1797 1653 1539 1363 1235 1136 1057 992 937

2143 1835 1626 1473 1355 1261 1183 1117 990 897 826 778 681 617 567 528 495 468

Spec. Gravity: 1.50

1 IPS

1 1/4 IPS

1 1/2 IPS

2 IPS

SDR-11

SDR-10

SDR-11

SDR-11

7744 13416 6628 11482 5874 10176 5322 9220 4896 8483 4555 7891 4274 7404 4037 6994 3578 6199 3242 5616 2983 5167 2775 4807 2459 4260 2228 3860 2050 3551 1907 3304 1789 3100 1690 2928

20260 17340 15368 13924 12810 11918 11182 10562 9361 8482 7803 7259 6434 5830 5363 4989 4681 4422

PROPANE

Pressure Drop: 1.0 in w.c. Length 1/2 IPS 3/4 IPS (feet) SDR-9.3 SDR-11

36402 31155 27612 25019 23017 21413 20091 18978 16820 15240 14020 13043 11560 10474 9636 8965 8411 7945

* Capacities listed are based on a pressure of 10 psig first stage setting and 1 psi pressure drop. * Values listed are in cubic feet/meter (cfm). To calculate BTU, multiply by 1000. ** Source: NFPA 58-2012 Table 15.1 (s) *Reproduced with permission from NFPA 54, National Fuel Gas Code, Copyright 2012. This reprinted material is not the complete and official position of the NFPA on the referenced subject, which is represented only by the standard in its entirety. Please consult your NFPA 54/ICC Fuel Gas codebook and appliance’s technical literature for more detailed sizing and installation instructions.

YELLOW TRACER WIRE

W-R#

Description

1842500 500’ Yellow Tracer Wire-14g 1842502 500’ Yellow Tracer Wire-18g - Use tracer wire in the trench along yellow polypipe for an effective, code-compliant installation.

YELLOW BURIAL TAPE

W-R#

Description

2426050 3” x 1000’ Non-Detectable 2426052 3” x 1000’ *Detectable* - Burial Tape is used 6 -8” above the pipe and tracer wire in the trench.

UNIVERSAL BRACKET FOR ANODELESS RISERS

Description

2867050 3/4” to 2” Riser Bracket - Fits 3/4” - 2” anodeless risers - Adjustable from 6” - 10” from wall

6 - 10” Adjustable

CALL (800) 221-1157

W-R#

·

www.wal-rich.com 30

·

FAX (516) 277-2177