COMAR Cladding 5P.i
7/8/09
12:35
Page 2
Uniclass
EPIC
L3811:P43 C421:X421 CI/SfB
(21·4) Xh4
comar5P.i Window Cladding Interfaces Aluminium window interfaces that allow a Comar window to be installed as a cladding panel.
The Parkside Group Ltd Unit 5, The Willow Centre 17 Willow Lane, Mitcham Surrey CR4 4NX Tel: +44(0) 20 8685 9685 Fax: +44(0) 20 8646 5096 Email:
[email protected] Web: www.comar-alu.co.uk
complementing architecture
COMAR Cladding 5P.i
7/8/09
12:35
Page 3
2
design Comar 5P.i Cladding Interfaces Cladding the building envelope can provide a striking solution to a
cladding interface, which mimics the edge profile of the cladding
design brief. However installing opening vents into claddings can
system. This allows the window to be installed in exactly the same
create issues with joint integrity. Traditionally, opening vents were
way as the panels.
installed with flashings and joint integrity relied on site applied
Comar 5P.i Cladding Interfaces provide cost effectiveness: site labour
sealant. The main disadvantage of this is long-term sealant
is reduced, due to the seamless integration of the window system into
degradation and lack of weather tightness of the façade.
the cladding.
Longevity of solution are the key words for Comar 5P.i Cladding
As the adaptor utilises Comar P.i technology, low U-values and dual
Interfaces. The adaptor allows the specifier the design opportunity to
colour options are available. The adaptor fits all window
incorporate windows into a façade without the need for additional
combinations, so a variety of tilt and turn, horizontal and vertical pivot,
flashings. The external frame of the windows incorporates the
top-swing, casement windows can be specified.
Integration Kingspan
Europanel
Kingspan’s 70mm and 80mm Optimo cladding has slim sight lines
Europanel wall cladding is a flat composite wall panel specially
which create a visually striking appearance. Available in cover widths
designed for panel integrity, joint performance and ease of
of 900 or 1000mm, the system has a hidden joint detail which conceals
construction with the widest range of modules available. Europanel
fasteners from view.
Premier system is a higher specification truly flat panel with a suite of
Comar’s Kingspan Panel Interfaces, allow window units to be prefabricated and “dropped” into the panel system facilitating the
integrated aluminum extruded trims and accessories including window integration, snap-on details, gasket joints and integrated louvres.
simple and quick construction that has become the standard with
Other Options
Kingspans systems. The advanced Optimo system also includes a
Comar’s Technical Department can produce profiles for other types of
broad range of project specific accessories for designers with simple
panels upon request. Please contact Comar’s Marketing Department
integration for doors and windows.
for further details.
COMAR Cladding 5P.i
7/8/09
12:35
Page 4
Comar 5P.i Window System
Window Configurations
The Comar 5P.i is a 60mm polyamide system that provides exceptional
horizontal and vertical pivot, tilt and turn, top-swing reversible and
thermal efficiency for applications where accurate U-value trade-offs
sliding windows. Comar 5P.i integrates with all Comar systems to
are required. Comar 5P.i answers the demands of the latest building
provide opening vents to window walling, curtain walling and ground
regulations by providing enhanced thermal performance, reducing
floor treatment, as well as the ability to be coupled together to form
heat loss and maintaining internal temperatures for longer. This
ribbon windows.
Comar 5P.i range includes window configurations, such as: casement,
directly impacts on the clients long term use of the building, reducing energy bills.
Installation
Comar 5P.i also provides a wealth of design possibilities with its dual
These adaptor profiles have been designed to match the top and
colour option: the internal face and external faces of the profiles can
bottom of ‘Kingspan’ and ‘Europanel’ interlocking panel joints,
be polyester powder coated or anodised in a multitude of colours and
enabling a window when fitted with these profiles, to be ‘dropped’
finishes. Comar 5P.i can incorporate through-frame or glazed-in
into the cladding system in the same way as a panel, eliminating the
ventilators from the Comar-Duco range. Comar 5P.i offers outstanding
need for any separate parts or flashings, thus maintaining the
weather performance, exceeding the requirements of the very latest
continuity of cladding construction. Comar 5P.i Cladding Interfaces
weather tightness tests: BS EN’s 1026, 1027 & 12211.
maintain the flush external appearance of the cladding.
Available Profiles Europanel
Kingspan Optimo
Profile
5mm Panel Joints
12mm Panel Joints
70mm
80mm
85mm
126mm
85mm
126mm
Sill
•
•
•
•
•
•
Jamb
•
•
•
•
•
•
Head
•
•
•
•
•
•
COMAR Cladding 5P.i
7/8/09
12:35
Page 5
4
Europanel Cladding Interfaces 126mm and 85mm Panels Typical Jamb Details
REAR AIR SEAL REAR AIR SEAL WINDOW FRAME INSERT
60
WINDOW INSERT WIDTH = ADAPTOR FRAME WIDTH-103mm
60
WINDOW FRAME INSERT
20
3MM THICK PRE-PUNCHED SPREADER WASHER BY OTHERS
51.5
EUROPANEL ADAPTOR FRAME WIDTH = EUROPANEL JOINT WIDTH - 31mm
‘OMEGA’ SECTION SUPPLIED AND FITTED BY OTHERS
15.5
WINDOW INSERT WIDTH = ADAPTOR FRAME WIDTH-103mm
54 51.5
EUROPANEL ADAPTOR FRAME WIDTH = EUROPANEL JOINT WIDTH - 31mm
15.5 CONTINUOUS 9X3mm BUTYL MASTIC BY OTHERS
CONTINUOUS 9X3mm BUTYL MASTIC BY OTHERS
126mm thick Europanel jamb detail using Omega sections EPH-02A, 2B and 2C
SASH SIZE = ADAPTOR FRAME WIDTH+63mm
126mm thick Europanel jamb detail using Omega sections PSH-02A and PSH-02B
REAR AIR SEAL
REAR AIR SEAL
EUROPANEL ADAPTOR FRAME WIDTH = EUROPANEL JOINT C WIDTH - 51mm
‘OMEGA’ SECTION SUPPLIED AND FITTED BY OTHERS
42.6
SASH SIZE = ADAPTOR FRAME WIDTH+63mm
31.5 25.5
‘OMEGA’ SECTION SUPPLIED AND FITTED BY OTHERS CONTINUOUS 9X3mm BUTYL MASTIC BY OTHERS
85mm thick Europanel jamb detail using Omega sections EPH-02A, 2B and 2C
EUROPANEL ADAPTOR FRAME WIDTH = EUROPANEL JOINT C WIDTH - 31mm
31.5 15.5
‘OMEGA’ SECTION SUPPLIED AND FITTED BY OTHERS CONTINUOUS 9X3mm BUTYL MASTIC
85mm thick Europanel jamb detail using Omega sections EPH-02A, 2B and 2C
COMAR Cladding 5P.i
7/8/09
12:35
Page 6
Europanel Cladding Interfaces 126mm and 85mm Panels Typical Head Details
SECONDARY STEELWORK BY OTHERS
SECONDARY STEELWORK BY OTHERS
EUROPANEL ‘PREMIER’ PANEL 126mm WIDE
EUROPANEL ‘PREMIER’ PANEL 126mm WIDE
3.5
5mm JOINT
ADDITIONAL PROFILES AT HEAD ONLY
126mm Europanel head detail for 12mm jointing system
WINDOW INSERT HEIGHT = ADAPTOR FRAME HEIGHT-103
51.84
ADAPTOR FRAME HEIGHT - MODULE HEIGHT-13mm
HEIGHT OF EUROPANEL MODULE
51.5 WINDOW INSERT HEIGHT = ADAPTOR FRAME HEIGHT-103
OVERALL EUROPANEL ADAPTOR FRAME HEIGHT PANEL MODULE CENTRES-13mm 7.5
CENTRES OF EUROPANEL MODULE
12mm JOINT
ADDITIONAL PROFILES AT HEAD ONLY
126mm Europanel head detail for 5mm jointing system
EUROPANEL ‘PREMIER’ PANEL 85mm WIDE
ADDITIONAL PROFILE AT HEAD ONLY
85mm Europanel head detail for 12mm jointing system
2
ADAPTOR FRAME HEIGHT = MODULE HEIGHT-13.5mm
FIXING ANGLE BACK TO SECONDARY STEEL DEPENDANT ON SITE CONDITIONS
SECONDARY STEELWORK BY OTHERS
4
2
5mm JOINT
SECONDARY STEELWORK BY OTHERS
HEIGHT OF PANEL MODULE
HEIGHT OF PANEL MODULE
ADAPTOR FRAME HEIGHT = MODULE HEIGHT-13.5mm 7.5
12mm JOINT
EUROPANEL ‘PREMIER’ PANEL 85mm WIDE
85mm Europanel head detail for 5mm jointing system
FIXING ANGLE BACK TO SECONDARY STEEL DEPENDANT ON SITE CONDITIONS ADDITIONAL PROFILE AT HEAD ONLY
COMAR Cladding 5P.i
7/8/09
12:35
Page 7
kings Europanel Cladding Interfaces 126mm and 85mm Panels Typical Sill Details
85mm Europanel sill detail for 5mm jointing system
SECONDARY STEELWORK BY OTHERS
126mm Europanel sill detail for 12mm jointing system
6
9.5 7
5mm JOINT
126mm Europanel sill detail for 5mm jointing system
PRESSED ALUM’ ANGLE BY WINDOW FABRICATOR
12mm JOINT
SECONDARY STEELWORK BY OTHERS
SECONDARY STEELWORK BY OTHERS
12mm JOINT
5mm JOINT 2.5
6
9.5
PRESSED ALUM’ ANGLE BY WINDOW FABRICATOR
85mm Europanel sill detail for 12mm jointing system
SECONDARY STEELWORK BY OTHERS
COMAR Cladding 5P.i
7/8/09
12:35
Page 8
kingspan Kingspan Interfaces 80mm Panels Typical Details
ADAPTOR FRAME SQUARE CUT AT HEAD
WINDOW INSERT MITRED CUT
KINGSPAN PANEL MODULE CENTRE LINE
ADAPTOR FRAME MITRED CUT AT SILL
CS489
SEE GLAZING OPTIONS
CS123
CLEAT REF WS416XSLF CHEVRON REF WS515XSLF
KINGSPAN PANEL MODULE CENTRE LINE
Jamb detail of window abutting ‘cut end’ of ‘Kingspan’ panel
2mm TOLERANCE ALLOWED FOR WINDOW FITTING TO ADAPTOR FRAME IN HEIGHT AND WIDTH
COVER SECTIONS EXTERNALLY AND INTERNALLY
ASSUMED STRUCTURAL STEEL WORK
CHEVRON REF WS515XSLF
CENTRE LINE OF VERTICAL JOINT IN PANELS
CLEAT REF WS416XSLF
‘KINGSPAN’ RECEIVER FLASHING CLEAT REF WS416XSLF
Jamb detail of window at vertical joint with ‘Kingspan’ panel
EXTERNAL SEALING OF WINDOW AT VERTICAL JOINTS WITH ‘KINGSPAN’ RECEIVER SECTION IS TO BE BY PANEL FITTERS
COMAR Cladding 5P.i
7/8/09
12:35
Page 1
Kingspan Cladding Interfaces 70mm Panels Typical Details
70
CS489
5.5
14
1
13.5
KINGSPAN PANEL MODULE CENTRE LINE
WINDOW WIDTH DIMENSION
WINDOW HEIGHT = ADAPTOR JAMB HEIGHT DIMENSION - 66mm
DIMENSION OF CUT PANEL LENGTH
CS488 COVER SECTIONS EXTERNALLY AND INTERNALLY
PANEL CENTRE MODULE - 44mm
Jamb detail of window at vertical joint with ‘Kingspan’ panel
ASSUMED STRUCTURAL STEEL WORK
2mm TOLERANCE ALLOWED FOR WINDOW FITTING TO ADAPTOR FRAME IN HEIGHT AND WIDTH
CHEVRON REF WS515XSLF
CENTRE LINE OF VERTICAL JOINT IN PANELS
CLEAT REF WS416XSLF
CLEAT REF WS416XSLF
70
1
HEIGHT OF ADAPTOR JAMB PROFILES = MODULE HEIGHT - 17mm
KINGSPAN PANEL JOINT CENTRE DIMENSIONS (E.G. 600-900-1000)
WINDOW SUPPORT RAIL BY OTHERS
6
WINDOW WIDTH DIMENSION = ADAPTOR LENGTH - 130mm
3.5
KINGSPAN PANEL MODULE CENTRE LINE
30
63.95
CHEVRON REF WS515XSLF
CLEAT REF WS416XSLF
CLEAT REF WS416XSLF 64
CUT HEAD AND SILL ADAPTORS TO PANEL JOINT CENTRES - 42mm DIMENSION TO VERTICAL ‘KINGSPAN’ PANEL JOINT CENTRES
ADAPTOR FRAME SQUARE CUT AT HEAD
‘KINGSPAN’ RECEIVER FLASHING 21
EXTERNAL SEALING OF WINDOW AT VERTICAL JOINTS WITH ‘KINGSPAN’ RECEIVER SECTION IS TO BE BY PANEL FITTERS
Technical Back-Up An experienced Sales Team covers the UK while the Technical Department offers an unsurpassed design and installation advice service to designers, specifiers and fabricators; simply call: +44(0) 20 8685 9685
WINDOW INSERT MITRED CUT
For More Information ADAPTOR FRAME MITRED CUT AT SILL
To find out more about this or any other Comar Architectural Aluminium System, or to obtain your personal copies of the COMAR TECHNICAL MANUALS call: +44(0) 20 8685 9685 or fax on: +44(0) 20 8646 5096