Just make it simple
National High-Tech Enterprise
International Accreditation Forum
CNAS C117-Q
UTEPO EoC IP Sur veillance Transmission System Solution
Coax for Network Transmission UTP704E/U TP701E-B1 Address: 5/F, Western Block,M-8 Building, Mid-section of Hi-tech Industrial Park,Nanshan District, Shenzhen. Telephone:+86-755-83898016 Fax:+86-755-83409500 E-mail:
[email protected]
Leading EoC Transmission Technology, High-speed Ethernet Signal, Support Various Cable, Long Distance, Strong Lighting Protection and Anti-interference Technology
www.utepo.net
For more information Please scan here with your smart phone
Just make it simple
www.utepo.net
U T E P O I P S u r ve i l l a n c e E O C Tr a n s m i s s i o n
Just Make IP Sur veillance Transmission Simple ● Expanding 10 times of IP sur veillance range ● Upgrade analog-IP sur veillance system without re-wiring EoC Coax IP Sur veillance Transmission Distance
1000 m Analog Sur veillance System
Coax Analog Camera
DVR
IP Sur veillance System
System Upgrade
Network Cable100m
Coax Network Cable IP Sur veillance Transmission Distance
UTP704E UTEPO EoC Transceiver
100 m
UTP704E UTEPO EoC Transceiver
NVR
Megapixel IP Camera
SHENZHEN UTEPO TECH CO.,LTD
Email:
[email protected]
Tel: +86-755-83898016
Fax: +86-755-83409500
www.utepo.net
连接接口
连接接口
How to upgrade the analog surveillance to IP surveillance more efficiency? As we all know, analog surveillance system use coax as transmission medium, usually one coax for
1ch video signal while IP surveillance use network cable as transmission medium. Therefore during the project of upgrading the analog surveillance system to IP HD surveillance system, the existing coax should be remove and the network cable need to be installed. In this way, it will cause the cost of cable and wiring. Especially for the locations like hotel, bank, the installation will cause great damage to the environment. That's why the customer says no to the IP surveillance system. Thus the usage of the existing transmission cable become the essential reason that affect the spread of the IP
UTEPO EoC IP HD Surveillance Transmission Solution Regarding this problem, UTEPO develops EoC network Extender to transfer high speed network signal over coax, 1 pair network cable, phone cable or even available wire. The Transmission distance can be 1500m, Max bandwidth is 134Mbps. For transmission distance within 300m, the EoC products can achieve the transmission for more than 10 pieces of mega pixel camera. In this way, it can upgrade the system without wiring, improve the spread of the system and lower the cost of the project.
surveillance system.
Traditional Analog Surveillance Transmission
Network Cable
Coaxial Cable
COAX ||
UTEPO Ethernet Coax Extender UTP704E
UTEPO Ethernet Coax Extender UTP704E
DVR Analog CCTV Camera
NVR
UTEPO Ethernet Phone Cable Extender UTP701E-B1 UTEPO Ethernet Phone Cable Extender UTP701E-B1
Phone Cable
Problem
1 : Cable Wasting
VDSL Phone Splitter
VDSL Phone Splitter
Phone Exchanger
Mega Pixel HD IP Camera
Problem
2 : Complicated Wiring Project EoC Transmission Technology Features
Problem
3 : High Labor Cost NO
Problem
4 : Long Term Project Circle
Problem
5 : Environment Damage
No Wiring Request It can adopts existing cable like coax, network cable, UTP cable, phone cable or even paired wire to transfer Ethernet signal and lower the project cost.
Support Various Device Support IP Phone, Wireless AP, Router, IP STB etc.. Various additional function can be setup on the surveillance system and achieve the request for the office and modern life.
High Transmission Rate
Easy Project The device support plug and play, can be installed in short time. Also it will not interrupt the environment and the resident.
It can provide signal transmission for several HD IP camera or IP device through 1 cable in related distance with bidirectional 100Mb bandwidth. Therefore improve the usage rate and value of the cable.
Long Extending Distance The Max extending distance can be 1500m, support medium and short distance IP surveillance signal transmission request.
1
Cable Saving, Labor Saving, Cost Saving
2
www.utepo.net
UTP704E
Panel Diagram
Network Extender Front Board
UTP704E is a new active network extender device that based on VDSL2 technology. The device can transfer 4ch network signal through Coaxial cable, UTP cable , telephone line and so on. It features strong isolation and lighting protection. Its Max transmission distance can be upto 1500m with 134Mbps transmission rate. The upgrade of the project will request no wiring project by using the existing cable. Also the UTP704E can transfer the phone signal without affect the quality of the phone signal while transferring the network signal.
GND
Network signal input/output Local LED
Back Board
Coaxial POWER
Power LED Local
Power
Remote
Online
Online LED
Power Supply: 12VDC; Remote LED
Transmission Medium:Support coax for network transmission, also support utp cable, phone cable and parallel cable;
12VDC
LED
Extending Distance: 1500m; Standard: IEEE802.3XILIE 10/100Base-TX and 100Base-FX Ethernet standard agreement; Operation: use existing network , easy operation, plug& play;
Explanation
on
Power supply is normal.
off
No power supply or power supply is abnormal.
LOCAL
on
Turn switch left and the LOCAL LED will be on,it works as local unit.
REMOTE
on
Turn switch right and the REMOTE LED will be on,it works as remote unit.
POWER
Transmission Rate: 100Mbps Max;
Status
BNC
ONLINE
Design: Support MIT specification, easy installation. Rj45
quick flash
Twice quick flashes after power is on,and then initialization.
slow flash
After initialization,Online LED will go on flashing,it's trying to connect the other device.I will need about 1minute.
quick flash on and off
Discontinuous quick flash means successful connection with another device
green LED
If on,relative ports are connected.
green LED
If off,relative ports are not connected.
yellow LED
Flashing means devices are communicating.
Installation Steps
Typical Aplication M
To make sure the transmission quality, please use standard cable.
on
ito
1. Connect port of UTP704E
r
N
Ne
V
tw
R
ut
Ne
tw
ork
Re
Ca
ble
mo
te
Un
it
p
ca
bl e an , p d p ho ar ne all el cab ca bl le e
Lo
ca
lU
ork
remote unit to IP cameras with network cable; Ca
2.Connect port of UTP704E local unit to NVR with network cable;
ble
n it
3. Connect the remote unit to
4. Examine the system
local unit with coax;
and power unit。
IP C am er a
3
4
www.utepo.net
连接接口 Specification Typical Application Item
Transmission Rate (26AWG)
Adjustment
LED
Power Adaptor
Adaptive Voltage Arrange
12VDC
Power Consumption