C Wall Cabinet Workstation Installation and User Manual

C36-430 Wall Cabinet Workstation Installation and User Manual Warnings IMPORTANT – Indicates a situation that does not present any hazard but is ver...
Author: Stewart Harrell
6 downloads 2 Views 5MB Size
C36-430 Wall Cabinet Workstation Installation and User Manual

Warnings IMPORTANT – Indicates a situation that does not present any hazard but is very important in maintaining a well functioning workstation. ATTENTION – Consult manual to avoid a potentially hazardous situation which may result in minor or moderate injury. o Contact the facility Engineer of Record for direction on mounting locations and methods prior to installing any wall tracks or equipment. o The shipping weight of this unit is 86 lbs (39.0 kg). Use proper lifting techniques to prevent injury.  ELECTRICAL – Indicates an impending electrical hazard which, if not avoided, may result in personal injury, fire and/or death. o The supplied power cord is rated for medical use. Connecting the cord to an outlet that is not medical grade (indicated with a green dot) will not ensure grounding protection. (Locking cabinet only). o Power cord, USB extension, and workstation are for INDOOR use only. DO NOT OPERATE OUTDOORS. o Keep power cord away from water. DO NOT PLUG CORD INTO OUTLET IF WET. o DO NOT OPERATE PRODUCT IF WET. If the WORKSTATION becomes wet, unplug it immediately, wipe off any excess liquid, and allow it to dry before using again. o Inspect power cord before integration. DO NOT USE POWER CORD IF DAMAGED. o Fully insert power cord plug into outlet. DO NOT unplug by pulling on cord. DO NOT remove, bend or modify any metal prongs or pins of power cord. o DO NOT use excessive force to make mechanical or electrical connections. o Do not use an electrical extension cord with your workstation. o Do not use a flammable cleaner on the station as it can result in fire or explosion. Transport/Storage

Care should be taken to transport and store this system within a temperature range of 32ºF to 90ºF (0ºC to 32ºC); Humidity 20% RH to 95% RH non-condensing. 2

Table of Contents Box Contents............................................................................ 5 Installation............................................................................... 5 Parts Breakdown................................................................. 6 Wall Cabinet Disassembly.................................................... 7 Fixed Height Wall Cabinet..................................................... 8 Height Adjustable Wall Cabinet........................................... 10 Wall Cabinet Reassembly................................................... 12 Integration............................................................................. 13 Technology Schematic....................................................... 13 Specifications.................................................................... 14. Technology Integration....................................................... 15 Software Installation............................................................. 20 Programmable Controller/Lock............................................. 26 Operation............................................................................... 32 Handle Release.................................................................. 32. Auto-Retract...................................................................... 32 Height Adjustment............................................................. 33 Override Lock.................................................................... 33 Maintenance.......................................................................... 34 Service................................................................................... 37 Warranty................................................................................ 37

Box Contents WORKSTATION x2 B

A

A

Cabinet

B

CPU Security Key

* C

Taped inside of cabinet

** D

Wall Cleat Cabinet Lock Override Key

E1 Fixed Template

* C

E2 Height Adjustable Template F

Fixed Hardware Kit

G

Height Adjustable Hardware Kit

** D

H

G E te pla t Tem Heigh ng unti 0 with y o M 43 ilit b C36 sta for Adju

the m of 4 botto the at the ns: line at floor. ion uctio bold m the tallat Instrgn the 45" frore for insints. • Ali plate prepa ting po tem and un rk d mo • Mantifie ide

x6 G1

x6 G2

x4 H1

x4 H2

ns:

t

Outle

tio Loca

F tion

est

us: t Sk bine 0 Ca le le le tab 6 43 r C3 table justab tab Adjus

net

tion

st posi

net

Lo 1799632 C36430 AR LH 1799633 C36430 1799634 C3 1799

be

at lowe

45"

from

r y te fo bilit pla sta em dju g T ight A n ti un He Mo hout wit 430 ns:

floor

C36

the m of ch botto at ea ed at the or. line flo provid uctio bold m the been the Instrgn the 45" fro have s. st with s • Ali plate ation g point s be of the tem le loc untin t align de s ho mo tha outsi ha • 3 the 4 set ons. ons er it of se the locati locati et aft oo d le cabin • Ch ility stu 4 ho the et. the re ck fac are cu ep to se the bra • Pr cket on bra hung been

43 C36 for y: ate bilit mpl sta binet g Te Adju Ca ntin ight ndard tract Mouout He6430 StaLockingRetract to Re Au L with 627 C36430AR Autocking,

late

ting

t Adj

Temp

Moun

1799628 C36430 R Lo LA 1799629 C36430 1799631 C3 1799

Heigh

#: 1802

ould

be

45"

from

floor

e sh

Lin

late

ting

934

Part

WC2

Fixed

Temp

Moun

#: 1803

*Note: For Fixed Height cabinets ONLY.. **Note: For Locking cabinets ONLY.

4

G1 #14 x 3" Pan Head

H1 Flat Head Wood Screw

Wood Screw

G2 1/4 – 20 x 2.00 Phillips Pan Head Screw

Skus

net

WC2

x4 H3

ns:

bi 0 Ca

022

catio

t Lo

Outle

e sh

Lin

Part

x6 G3

Cabi

jus t fo Ad ate t Adjus ight t Ad Heigh mpl igh , He Heigh ct, g Te H He cking tract, Retra ntin 6430LH Lo to Re , Auto Mou630 C36430HAR Au cking

ould

posi

at high

Cabi

G3 Wall Anchor

H2 1/4 – 20 x 2.00 Phillips Flat Head Screw

H3 Wall Anchor

Installation PARTS BREAKDOWN/RÉPARTITION DES PIÈCES/DETALLE DE LAS PIEZAS

Release Handle

Auto-Retract Solenoid*

Keypad

Monitor Bracket

IR Module

Override Lock**

Keyboard Platform

Mouse Pad

Tinted Monitor Cover

*Note: For cabinets with Auto-Retract ONLY. **Note: For Locking cabinets ONLY.

5

Installation Wall Cabinet Disassembly

 (1) Remove two screws from top of

1

tinted monitor cover. (2) Removed tinted monitor cover.

2

1 x2

2

 (1) Lift and (2) remove monitor bracket. Note: For Fixed Height Wall Cabinet installation, go to page 8. Note: For Height Adjustable Wall Cabinet installation, go to page 10.

2

1

6

Installation Fixed Height WALL Cabinet

 Note: Consult the Engineer of Record

1

regarding structural codes and utilities.

Use the mounting template (F) to mark drill hole locations. Set line should be

r y te fo bilit pla sta Tem Adju ng ht unti Heig Mo hout wit 0 43 ns:

atio

Outlet

of the

C36

Loc

430 king 962 AR 179 8 C36430 Loc 962 LAR 179 9 C36430 962 179 1 C36 963 179

be

45"

from

floo

r

tom

C36

e sho

Lin

the

43

Fixed

Templa

Mounti

s

et Sku

Cabin 430 C36 : te for pla tabilityinet Tem jus Cab ing t Ad rd ract unt igh nda Mo t He 430 StaLockingRetract o Ret Aut L o 7 C36430 Aut king, withou 962 AR 179 8 C36430 Loc 962 LAR 179 9 C36430 962 179 1 C36 963 179

Fixed

ng Mounti

d at

h

eac

be

Templa

#: 180393

"

45 cm) 4.3 (11

45"

from

floo

o 179 628 C36430 AR L 9 L 179 629 C36430 9 179 631 C 9 179

Part

WC2

Fixe

ing

ount

dM

934

kus

et S

in Cab 430 36 or Clity: f e t pla tabi inet Tem djus Cab ing t A ard t unt igh tand g t trac Mo out He6430 SLockin Retrac uto Re 3 A L with9627 C36430AR Autocking, r

uld

e sho

Lin

te

4 WC2

of the

plat of tem e loca unting aligns side hol mo that out has • 3 the 4 set tions. tions r it afte the of ose loca e loca inet cab • Cholity stud 4 hol the t. faci e the ure bracke par to sec the • Precket g on bra hun n bee

#: 180393

Part

bot

Loc

ns: d line at floor.provide the n the tructio bol bee Ins n the 45" fromhave s nts. t with e the • Alig tion poi bes

te ng 4 WC2 Part

template. Mark and drill holes.

ns:

atio

Outlet

uld

locations and dimensions on mounting

r y te fo bilit pla sta Tem Adju ng ht unti Heig Mo hout it 0w

s

et Sku

Cabin 430 C36 : te for pla tabilityinet Tem jus Cab ing t Ad rd ract unt igh nda Mo t He 430 StaLockingRetract o Ret L o , Aut Aut withou7 C36

45" (114.9 cm) from floor. Note outlet

F

h

tom eac bot the d at ns: d line at floor.provide the n the tructio bol bee Ins n the 45" fromhave s nts. t with e • Aligplat tion poi ns bes of the tem e loca unting alig side hol mo that out has • 3 the 4 set tions. tions r it afte the of ose loca e loca inet cab • Cholity stud 4 hol the t. faci e the ure bracke par to sec the • Precket g on bra hun n bee

om

5" fr

e4

b ould

r

floo

e sh

Lin

e

plat

Tem

03 #: 18

2

 ote: For steel stud, all six wall anchors N (G3) must be installed before proceeding.

Mount wall cleat (C) using pan head hardware provided. Note: Use part wall anchor (G3) and machine screw (G2) for steel stud installation. Use wood screws (G1) for wood studs.

C

x2

7

Installation Fixed Height WALL Cabinet

Hang wall cabinet (A) on wall cleat.

3



A

4

 Fold down keyboard tray half way to access mounting holes. Insert four screws to secure the cabinet crossmembers. Note: Use machine screws (G2) for steel stud installation. Use wood screws (G1) for wood studs.

x4

8

Installation HEIGHT ADJUSTABLE WALL Cabinet

 Note: Consult the Engineer of Record

1

regarding structural codes and utilities.

Use the mounting template (E) to mark

te pla t Tem Heigh ng unti with Mo 430 ility b C36 sta for Adju

of the om 4 bott at the at the r. s: tion line the flooallation truc bold Ins n the 45" from for instts. are e • Aligplat prep g poin ntin tem and k d mou • Mar tifie iden

drill hole locations. Set line should be

ns:

atio

let

Out

Loc

n t positio

s:

t Sku

t at

highes

t at

lowest

Cabine

ine

Cab

n positio

le

430 le C36stable stab stableAdjustab ht Adju Adju ht te for pla ht AdjuHeig Heightact, Heig Tem Heig , ing H king act, Retr unt 430LH Loc Retr, Auto Mo9630 C36430HAR Auto king Loc 179 2 C36430 R 963 LHA 179 3 C36430 963 179 4 C36 963 179

of the om 4 bott at the at the r. s: tion line the flooallation truc bold Ins n the 45" from for instts. are e • Aligplat prep g poin ntin tem and k d mou • Mar tifie iden

Cabine

ns:

r

uld

Line

be

45"

from

45” (114.9 cm) from floor. Note outlet

te pla t Tem Heigh ng unti with Mo 430 ility b C36 justa r fo Ad

atio

floo

let

Out

Loc

locations and dimensions on mounting

E

template. Mark and drill holes.

sho

n t positio

s: t Sku ine Cab le 430 le C36stable stab stableAdjustab ht Adju Adju ht te for pla ht AdjuHeig Heightact, Heig Tem Heig , Retr ing H kingRetract, Auto unt0 C36430LH Loc Auto ,

Mo

t at

highes

Cabine n positio t at

lowest

Cabine

king

430 963 HAR Loc 179 2 C36430 R 963 LHA 179 3 C36430 963 179 4 C36 963 179

r

uld

Line

e

Adj 2 WC2 Part

be

45"

from

floo

sho

g Templat Mountin

Height

#: 180202

45"m)

c 4.3 (11

te pla t Tem Heigh g in unt with Mo 430 ility b C36 sta for Adju

e

Adj 2 WC2 Part

g Templat Mountin

Height

#: 180202

us: t Sk ine Cab 430 le ble stable 6 b 3 ta r C stable djus justa t Adju

te fo dju ht A t Ad igh pla ht A Heig eigh ct, He Tem Heig g, ct, H etra ng 30H ockin etra to R unti 364 LH L to R , Au Mo9630 C36430HAR Auocking

2

L 179 632 C36430 HAR 9 L 179 633 C36430 9 179 634 C 9 179

 Note: For steel stud installation, four wall anchors (H3) must be installed before proceeding.

Start screws in top locations only. DO NOT tighten. Note: Use wall anchor (H3) and machine screws (H2) for steel stud installation. Use wood screws (H1) for wood studs.

x2

9

Installation HEIGHT ADJUSTABLE WALL Cabinet

 Hang wall cabinet (A) on top two screws.

3



A

x2

4

 Fold down keyboard tray half way to access mounting holes. Insert bottom two screws to secure the cabinet shuttle. Tighten all four screws. Note: Use machine screws (H2) for steel stud installation. Use wood screws (H1) for wood studs.



x2

10

Installation Wall Cabinet Reassembly

1

 Replace monitor bracket.

2

 (1) Replace tinted monitor cover.

Note: The user’s monitor needs to be attached to bracket, then hung in cabinet. See Integration section for details.

(2) Replace two screws on top of tinted monitor cover.

1

2 x2

11

Integration TECHNOLOGY SCHEMATIC

Power Cable

Power Strip*

Cable Grommet

Video Cable

Monitor

Mouse

CPU

USB Extender

Keyboard

*Note: For Fixed Height cabinets ONLY. **Note: For Height Adjustable cabinets ONLY.

12

Power Cord**

Integration Specifications Power Cord (Height Adjustable)

1 m Length, Medical Grade Right Angle NEMA Plug to C-13 plug, 120/240VAC, 6.3A, 50/60Hz.

Power Cord (Fixed Height)

2', Medical Grade Right Angle NEMA Plug (Illuminated for power indication) to C-13 plug.

Power Strip

NEMA 5/15 outlets with inline fusing

Power Indication (Powered Sku’s) Green LED Light mounted in the Monitor cabinet to provide power status. Power Indication (Base Model)

Illuminated Right Angle NEMA Power Plug.

USB (Control Board)

USB A to Mini-B

USB (TaskLight)

USB A to Mini-B

USB Peripherals

2 - USB A Male to USB A Female (Extension)

VGA / DVI Cable

Per Customer Technology Requirements

Monitor Bracket

25 lbs (11.3 kg) max; VESA 75 mm & 100 mm

Keyboard Platform

Accommodates 1.75" H x 18" W x 8" D (4.5 cm x 45.7 cm x 20.3 cm) USB keyboard

Work Surface

24.5" W x 9.4" D (62.2 cm x 23.9 cm)

Mouse Area

7" W x 9.5" D (17.8 cm x 24.1 cm)

Technology Cabinet

Accommodates CPUs up to 12" W x 10" H x 2.8" D (30.5 cm x 25.4 cm x 7.1 cm)

Technology integration

1 2 3

1 x2

13

Integration USING 24" MONITOR

 (1) Remove screw from IR module.

A1

(2) Remove IR module.

OPTIONAL

2

1

A2

 (1) Replace IR module. (2) Secure with two screws.

OPTIONAL

2

1

14

x2

Integration Technology integration

(1) Attach monitor bracket to monitor.

2

(2) Place monitor inside wall cabinet.

(3) Route power and video cables through cable grommet.

2

1

3

3

 (1) Replace tinted monitor cover. (2) Replace two screws on top of tinted monitor cover.

1

2 x2

15

Integration Technology integration

4

5

16

 Place CPU into cabinet. Make necessary electrical connections.

 Height Adjustable Cabinet – Connect power cord to bottom of cabinet. If needed, connect optional CAT5e cable (not provided).

Integration Technology integration

6

 Place keyboard and mouse into keyboard platform. Plug the USB connectors into the pre-wired USB extenders. Bundle excess cables and tuck under the worksurface. Note: Secure keyboard to drawer with velcro to avoid slipping.

17

Software Installation SOFTWARE SETUP Configuration of Software preferences: Installation (DO NOT plug USB cable in at this point): 1. Run LCDSecureIT - C36-430 Setup.msi setup file. 2. O  nce installation is complete plug in USB to an open port and wait for driver request. 3. The USB Driver is located within the files provided (at90usbxxx.inf) 4. After the USB drivers have been installed you can setup the software preferences. (see below) Shutdown the software Lower right-hand corner is a “Shutdown LCD SecureIT” button to completely close the software. If you close the window or press the “Send To Tray” button, it will be minimized to the system tray. Task Light Setup There are four options that are available when the keyboard is closed: • None (No action taken) • Immediate Blank Screen • Immediate Screen Saver (Select On resume, Password protect under screen saver options if user id and password is required) • Immediate lock computer screen You can adjust the duration of time the light will stay on at any given instance. (Default is 5 minutes). The password section is not applicable in this situation (Non-Locking Cabinets). Height Adjustability Setup (Height Adjustable models ONLY) There are two options for height adjustability: •C  abinet current limit allows administrators to define how much weight will be applied before the cabinet will stall. •C  abinet up / down Speed Limits control how fast the cabinet moves up or down.

18

Software Installation SOFTWARE SETUP Locking Setup There are four options for locking: • Locking Timeout enables locking feature and time duration when cabinet will lock. • PIN Code Management allows administrators to import/export pin code list to/from the cabinet. • Network Pin Management allows remote pin code management. • Pin List manages pin codes on the cabinet. Note: See “Programmable Controller/Lock” section for more details. Auto Retraction (Auto-Retract models ONLY) There is one option for auto retraction: • Retraction timeout enables the auto retraction feature and time duration when the drawer will close.

Status Information There are six options for status information: • If Drawer Is Closed is gray, no control board is present. If it is red, drawer is closed. If it is green, drawer is open. • If Drawer Is Locked is gray, no is device detected. If it is red, drawer is locked. If it is green, drawer is unlocked. • If User Presence Status is gray, no device is detected. If it is red, user is not present. If it is green, user is present. • If Tasklight Status is gray, no device is detected. If it is red, tasklight is off. If it is green, tasklight is on. • Version Information tells you software, firmware, and hardware revision versions. • Enter Bootloader is used to install/upgrade new firmware. Users should never have to use this function.

19

Programmable Controller/Lock Pin code locking cabinet only

Green LED

Red LED

Numeric Buttons

Clear Button

Lock Button

Raise Height Note: For Height Adjustable wall cabinets ONLY.

Lower Height Note: For Height Adjustable wall cabinets ONLY.

Programming Functions

Locking Timeout • Lock the Tray: Check this box to enable Locking Feature. Uncheck to disable. • Minutes and Seconds: This feature determines how long after a user walks away from the cabinet before the cabinet locks. Dropdown box allows admins to select anywhere from 5 seconds to 15 minutes.

20

Programmable Controller/Lock Pin code locking cabinet only

PIN Code Management • Copy PIN Codes from File to Device: This feature allows administrators to import pin code list into the cabinet. • Copy PIN Codes from Device to File: This features allows users to download all pins from this product (cabinet specific) to the local computer for backup.

Network Pin Management • This is an accessory feature that allows remote pin code management. Check box to enable this feature. This feature will not work without the network pin code management software sold seperatly.

Pin List • Digits in a Pin: Determines the length of pin codes (4 to 10 digits limitation). • Get List from Board: Populates a list in the pin list column from the control board. Pin list will show how many pins are stored on the control board below the list box. • Pin Addition: Pin entry is added here. User will add a pin defined around the number of digits defined in the “Digits in a Pin” section above. Once user has determined the pin code the “Add to List” Button will be pressed to populate to the pin list. • Remove Selected Button: In the pin list section, highlight a pin selected for removal, then click “Remove Selected” button to delete entry. • Commit Changes Button: Use this when all changes have been finalized. This will upload any pin entries/deletions to the control board. • Pin List and Pins Loaded: List of all pins stored on the control board and number of pins on control board.

21

Operation HANDLE RELEASE

1

 To close keyboard tray, pull release handle. Note: The tray will close automatically when the release handle is pulled.

se

Clo

AUTO-RETRACT

1

22

 Auto-Retract Cabinet – If the IR module does not detect activity after the preset amount of time, the auto-retract feature will close keyboard tray.

Operation ADJUSTING HEIGHT POSITION

 Height Adjustable Cabinet – (1)

1

Press up or down button on keypad to (2) adjust height position.

2

1

OVERRIDE LOCK

1

 Locking Cabinet – If keypad becomes inoperable, the override lock can be used to open the keyboard platform.

D

23

Maintenance 

DO NOT use the workstation if pieces are missing



or the unit is damaged. In these cases,

immediately contact Rubbermaid Customer Service for

• Remove pen and dry erase marker stains with a soft cloth and 91% isopropyl alcohol. • Remove iodine stains with a soft cloth and any

more information: 1-888-859-8294.

cleaners suggested above.

Cables: Always keep the cables neatly organized and be



sure to route cables away from moving components with



wire ties or

spirits, abrasive cleansers, paint thinner or any other harsh

cable clips.

or toxic chemicals.

Electric Cables: Periodically inspect power cord and plug

WOOD PANEL CARE

to ensure plug is not bent and cable is not frayed.

Harsh, abrasive and undiluted cleaning products may





DO NOT use the following chemicals to clean your workstation: acetone, mineral

cause damage to Deco Lam and the contact adhesive. Cleaning Pine Sol and Simple Green are cleaners that have been

CAUTION: Because of the close proximity of

approved for use on Deco Lam. A 30-1 ratio of water to



electrical power and equipment, flammable

cleaner is highly advised. Recommend water and a clean

cleaners should never be used on the workstation. • Verify that your workstation is unplugged from the wall outlet before cleaning. • Allow your workstation to dry completely before plugging the power cord into a wall outlet. • When cleaning the workstation, wipe surface with a damp cloth and thoroughly dry. • Never cover the workstation or its components with liquid or allow liquids to flow into the workstation. • Never use steel wool or other abrasive material as these could damage the surface finish. • Before using any cleaner on the workstation, first test on a small area to ensure that the surface is not harmed. • These guidelines cannot guarantee infection control. The hospital’s Infection Control Administrator should be consulted regarding cleaning procedures and schedules. • Clean plastic components with diluted, non-abrasive solutions. Suggested cleaners are water, soap, diluted bleach and alcohol solutions. 24

towel as a cleaning alternative to homeowners.

Troubleshooting Problem

Solution

Top door needs Open the top door and locate the 2 hinges on the right side. To adjust the door adjustment for alignment up or down use the inside screw of the hinges. To adjust the door right or left use the outside screw on the hinges. No Power

Check cable connections to power supply in the top cabinet.

Keypad lock not working

Use override key on the bottom left side.

Lift is not working

Ensure power cables are connected and power is available.

Unit does not function

Check power supply. Check wall outlet for power. Check USB communications cable. Check connectivity/communications with software.

Power supply does not turn on

Check power input cable.

Software does not show connectivity to control board

Check USB communications cable.

Check wall outlet for power. Check power supply. Check that the control board is not in bootloader mode - remove power from control board, wait 60 seconds and reconnect power. Check firmware version - update firmware if necessary.

25

Troubleshooting (continued) 

Problem

Solution

Software does not show connectivity to task light

Check USB communications cable. Unplug and reconnect USB cable to establish communications Check that automatic detection in software is enabled and verify connectivity. Check firmware version - update firmware if necessary.

Solenoid does not fire

Check connections. Press clear and lock button at the same time. Check that retract the tray box is checked. Check retraction time out time.

Solenoid does not fire

Check connections. Press clear and lock button at the same time. Check that retract the tray box is checked. Check retraction time out time.

Cabinet lock does not function

Check connections. Press lock button and re-enter pin code, then press lock again. Check that lock the tray box is checked. Check timing of lock cycle.

Keypad does not function Check connections. Look for LED status indicators Unplug and reconnect membrane cable. Linear actuator does not function

Check connections. Check for power to control board. Check that there is not excessive weight applied to the cabinet or obstructions in the way of travel. Check that speed limitations settings in software. Check membrane connector.

IR sensor does not operate

Check connections. Look for LED status indicators. Adjust gain control on IR sensor to adjust output.

Software does not operate

Restart computer. Uninstall/reinstall software. Check firmware version of task light/control board.

Pin code entry problems

Check membrane connector. Check pin code list in software. Check that the digits in the pin box and the number of digits being entered is equal.

26

Service Service Request Please visit our website at: www.rubbermaidmedical.com/service to file a request for parts. Service Level Commitment Rubbermaid Medical Solutions is committed to providing best-in-class service. This document details our standard warranty and instructions on how to request service using our customer support system.

Warranty LIMITED WARRANTY FOR WALL MOUNTED WORKSTATIONS Rubbermaid Medical Solutions (RMS) is pleased to offer a five-year warranty on durable components and a twoyear warranty on electronic components. If during the warranty period this RMS product proves defective in materials or workmanship under normal use by the original purchaser, please contact RMS technical support at www.rubbermaidmedical.com/service (please be sure to complete all information, including product serial number, description of the issue, and full contact information). RMS will determine, at its sole discretion, how to best address your warranty issue, which may include sending you a replacement part covered under warranty or for sale. RMS reserves the right to require proofof-purchase prior to honoring any warranty request. This warranty does not cover product abuse, modification, failure to adhere to product instructions, or improper operation/misuse. RMS SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state or country to country. Service Details Consumable components are not covered under warranty and include: • Cable grommet • Back panel of cabinet • Door lock and key • Pull latch for bottom door All other standard components will be replaced under the applicable warranty following a filed service request. If the service request is received prior to 10 am EST, replacement parts will ship next business day. Requests filed after 10 am EST will be fulfilled with parts shipped in 2 business days. All replacement parts will ship via ground carrier. *The above terms for replacement parts applies to facilities located in the United States. All other customers should contact the appropriate reseller for the terms of part replacement. 27

1-888-859-8294 www.RubbermaidMedical.com 06/2011 Part # 1803935 WC2 USER MANUAL © Rubbermaid Medical Solutions Huntersville, NC 28078