Terminal Blocks BN1U, BN-W/BNH-W, BA, BTB/BTBH, and BD
Terminal Blocks (Selection Guide) Rail Mount Terminal Blocks
Style
BND/BNDH Series
BN15MC Series
UL recognized CSA certified (600V) EN compliant (TÜV approved) Complies with JIS C 2811.
Double-deck. 8 mm (top deck), 10.5 mm (bottom deck) terminal centers.
All terminals are short-circuited with a built-in common jumper.
Terminal Centers
7 mm to 57 mm
8 mm, 10.5 mm
8 mm
7.9 to 60 mm
No. of Poles
Modular construction 1-pole = 1 block 2, 3, 4-pole = 1 block (large capacity)
4, 8, 10-pole
Modular construction, 1 pole = 1 block 3-pole = 1 block (for M3, M3.5, M4 terminal screws)
Series
BN-W/BNH-W Series
Rail Mount Terminal Blocks BA Series Three poles in one block. Made of polyamide.
Shape
Current (A)∗ 16 21 30 40 50 70 94 132 175 240 310 370 430 520
Wire (mm2)∗ 1.25 2 3.5 5.5 8 14 22 38 60 100 150 200 240 325
Applicable Wire Rated Current Terminal Screw
Terminal Screw∗ M3 M3.5 M4 M4 M5 M5 M6 M8 M8 M10 M12 M12 M16 M16
Wire (mm2)∗ 1.25
Current (A)∗ 16 Common Current
Terminal Screw∗ M3
∗ According to JIS C 2811.
Wire (mm2)∗ 1.25 2 3.5 5.5 14 22 38 100 200
Current (A)∗ 16 21 30 40 70 94 132 240 370
Terminal Screw∗ M3 M3.5 M4 M4 M5 M6 M8 M10 M12
∗ According to JIS C 2811.
∗ According to JIS C 2811. Self-lifting
Touch-down
Self-lifting
Self-lifting Terminal Shape
Screw (for large capacity type)
DIN 35 mm
Screw (for large capacity type)
Stud
IEC C30
DIN 35 mm + C30
DIN 35 mm DIN 35 mm + C30
Rail BAA BAP Rated Voltage
BNCA BNCP
BNJA
Insulation Resistance 100 MΩ minimum
600V 100 MΩ minimum
600V 100 MΩ minimum
Dielectric Strength
2500V AC, 1 minute
2500V AC, 1 minute
2500V AC, 1 minute
Housing Material (standard color)
Modified PPE (black)
Modified PPE (light gray)
PPE (black)
• Touch-down construction reduces wiring time. • Terminal blocks can be mounted on 3 different types of rails. • Molded from UL recognized flame-retardant resin UL94V-0. • Also available with a fuse or disconnecting switch.
• Same shape and size as • Large capacity terminal blocks BN15MW. can be surface mounted. • The housing color is light gray. • Also available with a fuse or disconnecting switch. • The same accessories can be used for standard types.
Features
Approvals Page
2
600V (660V)
BAA BAP
BNJA
UL, CSA, TÜV (major models) 5
— 18
19
UL, CSA 28
Terminal Blocks (Selection Guide) Rail Mount Terminal Blocks BN1U
Surface Mount Terminal Blocks
Rail Mount Miniature Terminal Blocks
Surface Mount Terminal Blocks
BD Series
BTB/BTBH Series
BD Series
Spring-up screws with temporary hold. UL recognized for field wiring (FW2).
Rugged surface mount terminal block with 8.5 to 15.5 mm terminal centers.
Space-saving miniature terminal block. Mount on 15-mm-wide DIN rail.
Miniature terminal block with 5, 7, 8 mm terminal centers.
7, 8, 11 mm
8.5, 10.5, 12, 15.5 mm
5, 7, 8 mm
5, 7, 8 mm
Modular construction
2 to 30-pole (2 to 20-pole for BTB50C and BTBH50C)
Modular construction 1-pole = 1 block
2 to 35-pole (8 mm terminal centers) 2 to 40-pole (7 mm terminal centers) 2 to 56-pole (5 mm terminal centers)
Wire (mm2)∗ 1.25 2 5.5
Current (A)∗ 16 21 40
Terminal Screw∗ M3 M3.5 M4
∗ According to JIS C 2811.
Current (A)∗ 16 21 40 70
Wire (mm2)∗ 1.25 2 5.5 14
Terminal Screw∗ M3 M3.5 M4 M5
∗ According to JIS C 2811.
Wire (mm2)∗ 1.25
Current (A)∗ 16, 14 (Note)
Terminal Screw∗
Wire (mm2)∗
M3
1.25
Current (A)∗ 16, 14 (Note)
Terminal Screw∗ M3
∗ According to JIS C 2811.
∗ According to JIS C 2811.
Note: 1 6A (8 mm terminal centers) 14A (7mm, 5 mm terminal centers)
Note: 16A (8 mm terminal centers) 14A (7mm, 5 mm terminal centers)
Self-lifting
Self-lifting
Self-lifting
Spring-up (with temporary hold function) Touch-down
DIN 35 mm
Screw/Solder
IEC C30 DIN 35 mm + C30
BNCA BNCP
Screw/Solder
Cage Screw
DIN 15 mm —
BAA BAP
Cage Screw
—
BDA BDP
BNJA
600V (660V) 100 MΩ minimum
600V 100 MΩ minimum
380V/250V 100 MΩ minimum
380V/250V 100 MΩ minimum
2500V AC, 1 minute
2500V AC, 1 minute
2500V AC, 1 minute
2500V AC, 1 minute
Modified PPE (black)
Modified PPE (black)
Modified PPE (black, blue – BD8 only)
Modified PPE (black)
• Spring-up screws save up to 30% wiring time (compared to IDEC standard terminal blocks). • Same height for M3, M3.5, and M4 types.
• Touch-down terminals. • Flame resistant UL94V-0. • Rugged construction.
• Miniature terminal blocks mount on 15-mm-wide DIN rail.
• Space-saving miniature terminal block. • Rugged construction.
UL, CSA, TÜV
UL, CSA, TÜV
UL, CSA
UL, CSA
34
37
45
46
3
Terminal Blocks Safety Precautions
Terminal Block Structure
• Remove power to the terminal blocks before starting installation, removal, wiring, maintenance, and inspection of the products. Failure to remove power may cause electrical shocks. • For wiring, use wires of proper size to meet voltage and current requirements. Tighten the terminal screws to the recommended tightening torque. Failure to tighten the terminal screws may cause overheating and fire. Also, the screws may become loose due to vibrations. Tighten regularly. • The recommended tightening torque is shown below: Screw Size M3 M3.5 M4 M5
Tightening Torque (N·m) 0.6 to 1.0 1.0 to 1.3 1.4 to 2.0 2.6 to 3.7
Screw Size M6 M8 M10 M12 M116
Tightening Torque (N·m) 3.9 to 5.4 10 to 13.5 21 to 28 38 to 49 83 to 116
• For large capacity types, take into consideration the tension of the wires and tightening torque and make sure that the crimping terminals are not twisted. • Grooves on the head of the hex bolt, for large capacity types are for temporary tightening. For proper tightening, use an applicable socket wrench and tighten within the range of the recommended tightening torque. • Use an insulated crimping terminal. • Install a dust cover after wiring.
Terminal Screw (Steel)
Housing Bus Bar (Brass) Spring (Stainless Steel)
Color: Black Material: Modified PPE
BNH10W (Example) Self-lifting
Touch-down
Screw (Large capacity type) Bus bar
Bus bar Sems plate
Bus bar
L-shaped washer Screw
Stud (Large capacity type)
Screw
Cage Screw Screw
Stud
Bus bar
Bus bar Nut
Cage
Terminal Styles
Selecting Terminal Blocks by Current According to JIS Standards IDEC’s terminal blocks are compliant with JIS C 2811. The current varies depending on the operationg conditions (wire type, number of budle wire, operating temperature, etc.). See the table below for choosing the terminal block. When using the terminal blocks as UL, CSA, and TÜV approved products, refer to UL, CSA, and TÜV ratings.
Applicable IDEC Terminal Block
Applicable Wire 1.25 2 3.5 (mm2) Current (A) 16 21 30 Current vs. Temperature (1) (2) (3) Rise at Bus Bars BN1U Series BN1U-16W BN1U-20W — BN15LW BN10W BNH15LW BNH10W BN15MWT BN-W BN15MW BNH15MWT BN15LWT BNH-W BNH15MW BND15LW BNH15LWT Series BND15W BNDH15LW BNDH15W BND15WT BNDH15WT BA Series BA111T BA211T — BTB BTB15C BTB15LC — BTBH Series BTBH15C BTBH15LC BD8 BD Series BD8S
5.5
8
14
22
38
60
100
150
200
240
325
40
50
70
94
132
175
240
310
370
430
520
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)Cu
BN1U-40W
BN30W BNH30W
BA311T BTB30C BTBH30C
—
BN40W BNH40W
— —
BN50W BNH50W
BN75W
BA411S BA611S BTB50C BTBH50C
BN100W
BN150W BN200BW BN300BW BN400BW BN500BW BN600NW BN150NW BN200NW BN300NW BN400NW BN500NW
BA711S
BA811S
—
BA911S
—
—
— —
Current vs. Temperature Rise at Bus Bars (1) 1.25 mm2
Temperature rise of bus bars (°C)
60
(2) 2 mm2
(6) (3) (4) (5) (7) 3.5 mm2 5.5 mm2 8 mm2 14 mm2 22 mm2
(8) 38 mm2
(9) 60 mm2
(10) (11) (12) (13) (14) 100 mm2 150 mm2 200 mm2 250 mm2 325 mm2
45 40 30
20 15
10
5
10
20
30
40
50
70
Current (A)
100
200
300
400
500 600 700
How to read the graph When using IDEC terminal blocks, make sure that the operating temperature and the temperature of the bus bars do not exceed 100°C. However, the upper limit of the temperature rise is limited to 45°C by JIS C 2811. Operating temperature + Temperature rise at bus bars ≤ 100°C Note: Select wires according to the allowable temperature, operating temperature, and temperature rise of bus bars. About SCCR of Terminal Block When exporting machine or systems to the USA, the smallest short-circuit current rating of the control board’s main circuit must be displayed as SCCR (short-circuit current rating) value. SCCR is specified by UL508A-2001, Supplement SB, Table SB4.1. The value is 10kA for terminal block.
4
BN-W / BNH-W Series Terminal Blocks UL recognized, CSA certified, and TÜV compliant. Touch-down terminals reduce wiring time. • Molded from UL94V-0 material with excellent flame and shock resistance. • Terminal blocks can be mounted on a 35-mm-wide DIN rail and 30-mm-wide IEC type C rail. DIN Rail
IEC Type C Rail
• 9.5-mm-wide marking strips can be used on all models. 17-mm-wide sliding type marking strips also available. (BN10W to BN30W) • Terminal blocks of different shapes and capacities can be installed without using an end plate. (BN/BNH10W to BN/BNH150W) • Screw and stud terminals available for large capacity terminal blocks. Touch-down terminal blocks reduce wiring time. • Additional mounting and removal of terminals is easy. (BNH-W/BNDH-W Series) (BN/BNH10W to BN/BNH30W) 1. Insert the Crimping 2. P ush the Screw 3. Tighten the Screw •• Complies with JIS C 2811. Terminal Down •• UL recognized, CSA certified, and EN compliant (TÜV approved). (Except common terminal and models with fuse) •• UL recognized for field wiring (FW2). Applicable Standards
Certification Organization/ File No.
Mark
UL1059
UL recognized File No. E78117
CSA C 22.2 No.158
CSA File No. LR64803
EN60947-7-1
TÜV Rheinland License No. Standard: R9551701 Large Capacity: J9551516 J9650886 (BN500, BN600 only) Double-Deck: R9650688
Material Parts Name Housing Bus Bars Terminal Screw Spring
Terminal screw is always in the open position. No need to loosen the screw.
Push the screw down to temporarily hold the wire in place.
The screws can be tightened easily with a pneumatic screwdriver.
General Ratings Dielectric Strength Insulation Resistance Operating Temperature Storage Temperature Operating Humidity
Material Modified PPE Brass (Nickel-plated) Steel (Zinc chrome-plated) Stainless steel (touch-down type only)
2500V AC, 1 minute 100 MΩ minimum –25 to +55°C (no freezing) –25 to +70°C (no freezing) 45 to 85% RH (no condensation)
Ratings/Terminal Screw Tightening Torque Part No. Style
Self-Lifting BN10W
BN15MW
Standard
Large Capacity
With Disconnecting Switch With Fuse
Double-Deck Common Terminal
UL/CSA Ratings Voltage/ Wire Size Current (AWG) 600V/15A 22-16
Touch-Down BNH10W
BNH15MW 600V/15A
22-14
EN Ratings (∗1) Voltage/ Wire Size [mm2/(AWG)] Current 660V/16A 1.25/(22-16)
JIS Ratings Voltage/ Wire Size Current (mm2) 600V/16A 1.25
M3
0.6 to 1.0
660V/22A
600V/16A
M3
0.6 to 1.0
2/(22-14)
BN15LW
BNH15LW 600V/20A
22-14
660V/22A
2/(22-14)
600V/21A
1.25 (2) ∗2 2
BN15MWT
BNH15MWT 600V/15A
22-14
660V/22A
2/(22-14)
600V/21A
2
Terminal Screw
Tightening Torque (N·m)
M3.5
1.0 to 1.3
M3.5
1.0 to 1.3
BN15LWT
BNH15LWT 600V/30A
22-14
660V/22A
3.5/(22-14)
600V/30A
3.5
M4
1.4 to 2.0
BN30W
BNH30W
18-10
660V/38A
5.5/(18-10)
600V/40A
5.5
M4
1.4 to 2.0
600V/35A
BN40W
BNH40W
600V/40A
16-8
660V/50A
8/(16-8)
600V/50A
8
M5
2.6 to 3.7
BN50W
BNH50W
600V/50A
16-6
660V/67A
14/(16-6)
600V/70A
14
M5
2.6 to 3.7
BN75W
3.9 to 5.4
600V/80A
16-4
660V/94A
22/(8-4)
600V/94A
22
M6
BN100W
600V/100A
16-2
660V/132A
38/(2)
600V/132A
38
M8
BN150W
600V/150A
16-1/0
660V/175A
60/(1/0)
600V/175A
60
M8
BN150NW
600V/150A
16-1/0
660V/175A
60/(1/0)
600V/175A
60
M8
BN200BW, BN200NW
600V/200A
4/0
660V/240A
100/(4/0)
600V/240A
100
M10 M10
BN300BW, BN300NW
600V/310A
300MCM
660V/310A
150/(300MCM)
600V/310A
150
BN400BW, BN400NW
600V/350A
400MCM
660V/370A
200/(400MCM)
600V/370A
200
M12
BN500BW, BN500NW
600V/500A
500MCM
660V/430A
240/(500MCM)
600V/430A
250
M16
BN600NW
600V/600A
600MCM
660V/520A
300/(600MCM)
600V/520A
325
M16
BNT20
—
—
—
—
—
600V/20A
5.5
M4
BNF10S
—
—
—
—
—
600V/10A
5.5
M4
BNF10N
1.4 to 2.0 1.4 to 2.0
600V/10A
5.5
M4
22-14
660V/22A
2/(22-14)
600V/16A
M3
0.6 to 1.0
BND15LW
BNDH15LW
600V/15A
22-14
660V/22A
2/(22-14)
600V/21A
1.25 (2) ∗2 2
M3.5
1.0 to 1.3
BND15WT
BNDH15WT
600V/15A
22-14
660V/22A
2/(22-14)
600V/21A 600V/16A
2
M3.5
1.0 to 1.3
1.25 (2) ∗2
M3
0.6 to 1.0
—
—
83 to 116
600V/10A
—
—
38 to 49
BNDH15W
—
—
10 to 13.5 21 to 28
BND15W
BN15MC
—
10 to 13.5
—
—
Common Current
∗1: Ratings approved by TÜV based on EN60947-7-1. ∗2: The rated applicable wire size is 1.25 mm2, but 2 mm2 wires can also be connected. The wire size in ( ) does not comply with JIS standards. ∗3: Part No. with is UL recognized for field wiring (FW2).
5
BN-W / BNH-W Series Terminal Blocks Terminal Blocks Terminal Style
Ordering No.
Applicable Wire (mm2)
Terminal Screw
Width (mm)
Package Quantity
BN10W BN15MW BN15LW BN15MWT BN15LWT BN30W BN40W BN50W BNH10W BNH15MW BNH15LW BNH15MWT BNH15LWT BNH30W BNH40W BNH50W
BN10WPN50 BN15MWPN50 BN15LWPN50 BN15MWTPN50 BN15LWTPN50 BN30WPN50 BN40WPN20 BN50WPN20 BNH10WPN50 BNH15MWPN50 BNH15LWPN50 BNH15MWTPN50 BNH15LWTPN50 BNH30WPN50 BNH40WPN20 BNH50WPN20
1.25 1.25 (2) (Note) 2 2 3.5 5.5 8 14 1.25 1.25 (2) (Note) 2 2 3.5 5.5 8 14
M3 M3 M3.5 M3.5 M4 M4 M5 M5 M3 M3 M3.5 M3.5 M4 M4 M5 M5
7 8 10.5 8 10.5 12 14 15.5 7 8 10.5 8 10.5 12 14 15.5
50 50 50 50 50 50 20 20 50 50 50 50 50 50 20 20
BN75W BN100W BN150W BN200BW2 BN200BW3 BN200BW4 BN300BW2 BN300BW3 BN300BW4 BN400BW2 BN400BW3 BN400BW4 BN150NW BN200NW2 BN200NW3 BN200NW4 BN300NW2 BN300NW3 BN300NW4 BN400NW2 BN400NW3 BN400NW4
BN75WPN10 BN100WPN05 BN150WPN05 BN200BW2 BN200BW3 BN200BW4 BN300BW2 BN300BW3 BN300BW4 BN400BW2 BN400BW3 BN400BW4 BN150NWPN05 BN200NW2 BN200NW3 BN200NW4 BN300NW2 BN300NW3 BN300NW4 BN400NW2 BN400NW3 BN400NW4
22 38 60
M6 M8 M8
20 26 26
10 5 5
12
100
M10
37
1
13
150
M10
44
1
14
200
M12
57
1
15
60
M8
26
5
12
100
M10
37
1
13
150
M10
44
1
14
200
M12
57
1
15
BN200BW2K BN200BW3K BN200BW4K BN300BW2K BN300BW3K BN300BW4K BN400BW2K BN400BW3K BN400BW4K BN500BW2K BN500BW3K BN500BW4K BN200NW2K BN200NW3K BN200NW4K BN300NW2K BN300NW3K BN300NW4K BN400NW2K BN400NW3K BN400NW4K BN500NW2K BN500NW3K BN500NW4K BN600NW2K BN600NW3K BN600NW4K
BN200BW2K BN200BW3K BN200BW4K BN300BW2K BN300BW3K BN300BW4K BN400BW2K BN400BW3K BN400BW4K BN500BW2K BN500BW3K BN500BW4K BN200NW2K BN200NW3K BN200NW4K BN300NW2K BN300NW3K BN300NW4K BN400NW2K BN400NW3K BN400NW4K BN500NW2K BN500NW3K BN500NW4K BN600NW2K BN600NW3K BN600NW4K
100
M10
37
1
13
150
M10
44
1
14
200
M12
57
1
15
250
M16
57
1
16
100
M10
37
1
13
150
M10
44
1
14
200
M12
57
1
15
250
M16
57
1
Part No.
Page
Standard 16A 21A Self-Lifting
1-pole
30A 40A 50A 70A 16A 21A
Touch-Down
1-pole
30A 40A 50A 70A
8
9 10 8
9 10
Large Capacity (Rail Mount) 1-pole
Screw
Stud
2-pole 3-pole 4-pole 2-pole 3-pole 4-pole 2-pole 3-pole 4-pole 1-pole 2-pole 3-pole 4-pole 2-pole 3-pole 4-pole 2-pole 3-pole 4-pole
94A 132A 175A 240A
310A
370A 175A 240A
310A
370A
11
Large Capacity (Surface Mount)
Screw
Stud
2-pole 3-pole 4-pole 2-pole 3-pole 4-pole 2-pole 3-pole 4-pole 2-pole 3-pole 4-pole 2-pole 3-pole 4-pole 2-pole 3-pole 4-pole 2-pole 3-pole 4-pole 2-pole 3-pole 4-pole 2-pole 3-pole 4-pole
240A
310A
370A
430A
240A
310A
370A
430A
520A
∗ The rated applicable wire size is 1.25 mm2, but 2 mm2 wires can also be connected. The wire size in ( ) does not comply with JIS standards.
6
16 325
M16
57
1
BN-W / BNH-W Series Terminal Blocks Terminal Blocks Terminal Style
Part No.
Ordering No.
Applicable Wire (mm2)
Terminal Screw
Width (mm)
Package Quantity
5.5
M4
15
20
5.5
M4
15
20
1.25 (2)∗
M3
8
25
2
M3.5
8
25
2
M3.5
12
25
1.25 (2)∗
M3
8
10
Page
With Disconnecting Switch, Fuse Disconnecting Switch 20A
1-pole
With Fuse
1-pole
10A
BNT20 BNF10S- BNF10N-
BNT20PN20 BNF10S-APN20 BNF10N-APN20
BND15W BNDH15W BND15LW BNDH15LW BND15WT BNDH15WT
BND15WPN25 BNDH15WPN25 BND15LWPN25 BNDH15LWPN25 BND15WTPN25 BNDH15WTPN25
BN15MC4 BN15MC8 BN15MC10
BN15MC4PN10 BN15MC8PN10 BN15MC10PN10
17
Double-Deck Terminal Block Self-Lifiting Touch-Down Self-Lifting Touch-Down Self-Lifting Touch-Down
16A
1-pole
21A
1-pole
21A
1-pole
18
Common Terminal Self-Lifting Type 16A (Common Current)
4-pole 8-pole 10-pole
18
∗ The wire size in ( ) does not comply with JIS standards. The rated applicable wire size is 1.25 mm2, but 2 mm2 wires can also be connected. Specify the fuse rating in place of . 1A: 1, 3A: 3, 5A: 5.
Accessories
End Plate
Rail
End Clip
Rail Mounting Clip
Dust Cover
Marking Strip
Marking Strip Fastener
Sliding Marking Strip
Jumper
Removal Tool
Surface Mount Clip
Connecting Rod
Connecting Nut
BN10W, BN15MW, BN15LW, BN15MWT, BN15LWT, BN30W
✕
✕
✕
—
—
—
BNH10W, BNH15MW, BNH15LW, BNH15MWT, BNH15LWT, BNH30W
✕
✕
✕
—
—
—
—
50A to 70A Self-Lifting Touch-Down
BN40W, BN50W, BNH40W, BNH50W
✕
✕
✕
—
—
—
—
—
Rail Mount 1-Pole 94A to 175A
BN75W, BN100W, BN150W, BN150NW
✕
✕
✕
—
—
—
—
—
—
Rail Mount 240A to 370A
BN200BW, BN300BW, BN400BW BN200NW, BN300NW, BN400NW
—
✕
✕
—
—
—
—
—
—
—
BN200BWK, BN300BWK, BN400BWK BN200NWK, BN300NWK, BN400NWK BN500BWK, BN500NWK, BN600NWK
—
—
—
—
Supplied
—
Surface Mount 240A to 520A
Supplied
Accessories (✕: Necessary)
—
—
—
—
—
—
—
With Disconnecting Switch
BNT20
✕
✕
✕
—
—
—
—
—
—
With Fuse
BNF10S, BNF10N
✕
✕
✕
—
—
—
—
—
—
—
Double-Deck
BND15W, BND15LW, BNDH15W, BNDH15LW, BND15WT, BNDH15WT
✕
✕ ∗1
✕ ∗1
—
✕
—
✕ ∗2
✕
✕
Common Terminal
BN15MC
—
✕
✕
—
—
—
—
—
—
When ordering accessories, check if the accessories are necessary by referring to the table. ✕: Necessary : Optional
Large Capacity
Standard
Terminal 16A to 40A Self-Lifting Touch-Down
Part No.
∗1: Accessory not necessary for surface mounting. ∗2: Accessory not necessary for rail mounting. Specify the number of poles in place of .
20
21
22
23
24
Page
7
BN-W / BNH-W Series Terminal Blocks
32.5
35 (when using C Rail: 41)
23.5 (when using C Rail: 29.5)
32.5
35 (when using C Rail: 41)
BN15MWPN50 50
50
Weight (Approx.)
6.5g
7.3g
10g
32.5
BNH10WPN50
14.3 10.5 8.5
38 18
35 (when using C Rail: 41)
18
35 (when using C Rail: 41)
32.5
11.3 8 6.7
38
BNH15MWPN50
BNH15LWPN50
Package Quantity
50
50
50
Weight (Approx.)
7.5g
8.2g
11.2g
Standards Insulation Voltage Wire Size ∗1 Rated Current ∗2
UL/CSA
EN
JIS
UL/CSA
EN
JIS
UL/CSA
EN
JIS
600V
660V
600V
600V
660V
600V
600V
660V
600V
22-16 AWG
1.25 mm2 (22-16 AWG)
1.25 mm2
22-14 AWG
22-14 AWG
2 mm2 (22-14 AWG)
2 mm2
15A
16A
16A
15A
22A
21A
Terminal screw
1.25 mm2 2 mm2 (22-14 AWG) (2mm2 max) 22A
M3.5
1.25-3
1.25-3 (2-3)
2-3.5
2
2
2
0.6 to 1.0 N · m
0.6 to 1.0 N · m
1.0 to 1.3 N · m
ø3.2 min.
End Plate Dust Cover Marking Strip Marking Strip Fastner DIN Rail/End Clip C Rail/End Clip DIN + C Rail/End Clip
20A
M3
Crimping Terminal
Crimping Terminal Dimensions (mm) ∗3
16A
M3
Max. No. of Crimping Terminals
Tightening Torque
M3.5
21A
BNH15LW
32.5
10.3 7 5.9
18
M3
16A
BNH15MW
23.5 (when using C Rail: 29.5)
Dimensions
BN15LWPN50
23.5 (when using C Rail: 29.5)
M3
16A
BNH10W
35 (when using C Rail: 41) 23.5 (when using C Rail: 29.5)
Touch-Down Terminal
14.3 10.5 8.5
38 18
50
38
Accessories
11.3 8 6.7
BN10WPN50
Part No.
M3.5
21A
BN15LW
Package Quantity
Ordering No.
Specification / Ratings
38 18
10.3 7 5.9
32.5
35 (when using C Rail: 41)
38 18
M3
16A
BN15MW
23.5 (when using C Rail: 29.5)
Dimensions
Ordering No. Standard
M3
16A
BN10W
23.5 (when using C Rail: 29.5)
Self-Lifting Terminal
Part No.
5 max.
ø3.6 min.
ø3.2 min.
5.8 max.
6.6 max. 3.3 min.
5 max.
8.5 max.
3.3 min.
5 max.
4 min.
BNE15W (see page 20) BNC230 (see page 21) PVC 1m/BNM7, Fiber glass 1m/BNM9, PVC 25m/BNM725 (see page 22) BNM3 (see page 22) Aluminum: BAA1000, Steel: BAP1000 (see page 20)/BNL6 (see page 21) Aluminum: BNCA1000, Steel: BNCP1000 (see page 20)/BNL7 (see page 21) Aluminum: BNJA1000 (see page 20)/BNL6, BNL7 (see page 21)
∗1: The wire size in ( ) does not comply with JIS standards. ∗2: The rated current differs according to operating conditions. See “Selecting Terminal Blocks by Current According to JIS Standards” on page 4. ∗3: Use a CSA certified crimping terminal when using the terminal block as a CSA certified product.
8
BN-W / BNH-W Series Terminal Blocks
19.4
32.5
35 (when using C Rail: 41)
23.5 (when using C Rail: 29.5)
32.5
15.8 12 9.6
38
14.3 10.5 8.5
BN15MWTPN50
BN15LWTPN50
50
50
50
7g
10g
15.6g
BNH15MWTPN50
15.8 12 9.6
38 19.4
32.5
35 (when using C Rail: 41) 23.5 (when using C Rail: 29.5)
32.5
23.5 (when using C Rail: 29.5)
14.3 10.5 8.5
38 17.5
M4
40A
BNH30W
BNH15LWTPN50
35.5
11.3 8 6.7
38 17.5
M4
30A
BNH15LWT
BN30WPN50
38 (when using C Rail: 44) 25.4 (when using C Rail: 31.4)
M3.5
21A
BNH15MWT
35 (when using C Rail: 41)
38 17.5
M4
40A
BN30W
35.5
11.3 8 6.7
23.5 (when using C Rail: 29.5)
35 (when using C Rail: 41)
38 17.5
M4
30A
BN15LWT
38 (when using C Rail: 44) 25.4 (when using C Rail: 31.4)
M3.5
21A
BN15MWT
BNH30WPN50
50
50
50
8g
11g
16.8g
UL/CSA
EN
JIS
UL/CSA
EN
JIS
UL/CSA
EN
JIS
600V
660V
600V
600V
660V
600V
600V
660V
600V
22-14 AWG
2 mm2 (22-14 AWG)
2 mm2
22-14 AWG
3.5 mm2 (22-14 AWG)
3.5 mm2
18-10 AWG
5.5 mm2 (18-10 AWG)
5.5 mm2
22A
21A
30A
22A
30A
35A
38A
40A
15A
M3.5
M4
M4
1.25-3.5 to 2-3.5
1.25-4 to 3.5-4
1.25-4 to 5.5-4
2
2
2
1.0 to 1.3 N·m
1.4 to 2.0 N·m
1.4 to 2.0 N · m
ø3.6 min. 8.5 max.
6.6 max. 4.7 max.
ø4.2 min.
ø4.3 min.
3.6 min.
4.7 max.
9.5 max. 4.3 min.
6 max.
4.5 min.
BNE15W (see page 20)
BNE30W (see page 20)
BNC230 (see page 21)
BNC230 (see page 21)
PVC 1m/BNM7, Fiber glass 1m/BNM9, PVC 25m/725 (see page 22) BNM3 (see page 22) Aluminum: BAA1000, Steel: BAP1000 (see page 20) /BNL6 (see page 21) Aluminum: BNCA1000, Steel: BNCP1000 (see page 20)/BNL7 (see page 21) Aluminum: BNJA1000 (see page 20)/BNL6 (see page 21)
Aluminum: BNJA1000 (see page 20)/ BNL6, BNL7 (see page 21)
∗1: The wire size in ( ) does not comply with JIS standards. ∗2: The rated current differs according to operating conditions. See “Selecting Terminal Blocks by Current According to JIS Standards” on page 4. ∗3: Use a CSA certified crimping terminal when using the terminal block as a CSA certified product.
9
BN-W / BNH-W Series Terminal Blocks
34.3 28.3
42.5
When using C Rail: 50
When using DIN Rail: 44
34.4 28.4
42.5
When using C Rail: 50
20
Weight (Approx.)
25g
25.4g
50A
48 24.4
BNH40WPN20
Ordering No.
34.3 28.3
20
20
Weight (Approx.)
25g
29g
Insulation Voltage Wire Size ∗1 Rated Current ∗2 Terminal screw Crimping Terminal
UL/CSA
EN
JIS
UL/CSA
EN
JIS
600V
660V
600V
600V
660V
600V
16-8 AWG
8 mm2 (16-8 AWG)
8 mm2
16-6 AWG
14 mm2 (16-6 AWG)
14 mm2
40A
50A
50A
50A
67A
70A
M5
M5
1.25-5 to 8-5
1.25-5 to 14-5
2
2
2.6 to 3.7 N · m
2.6 to 3.7 N · m
Max. No. of Crimping Terminals
Tightening Torque
ø5.2 min.
Accessories
Crimping Terminal Dimensions (mm) ∗3
18 15.5 13
BNH50WPN20
Package Quantity Standards
M5
42.5
When using C Rail: 50 42.5
17.8 14 12
When using C Rail: 50
43 22.4
Dimensions
70A
BNH50W
M5
When using DIN Rail: 44
BNH40W
When using DIN Rail: 44
Touch-Down Terminal
BN50WPN20
20
34.4 28.4
Standard
18 15.5 13
Package Quantity Part No.
M5
48 24.4
17.8 14 12
BN40WPN20
Ordering No.
Specification / Ratings
70A
BN50W
M5
43 22.4
Dimensions
When using DIN Rail: 44
Self-Lifting Terminal
50A
BN40W
Part No.
ø5.2 min. 12.8 max.
11.8 max. 6.8 max.
6.3 min.
6.5 max.
4.5 min.
End Plate
BNE40W (see page 20)
BNE50W (see page 20)
Dust cover
BNC330 (see page 21)
BNC320 (see page 21)
Marking Strip Marking Strip Fastner DIN Rail/End Clip C Rail/End Clip DIN + C Rail/End Clip
PVC 1m/BNM7, Fiber glass 1m/BNM9, PVC 25m/725 (see page 22) BNM3 (see page 22) Aluminum: BAA1000, Steel: BAP1000 (see page 20)/ Aluminum: BAA1000, Steel: BAP1000 (see page 20)/ BNL6 (see page 21) BNL8 (see page 21) Aluminum: BNCA1000, Steel: BNCP1000 (see page 20)/ Aluminum: BNCA1000, Steel: BNCP1000 (see page 20)/ BNL7 (see page 21) BNL8 (see page 21) Aluminum: BNJA1000 (see page 20)/ Aluminum: BNJA1000 (see page 20) BNL6, BNL7 (see page 21) /BNL8 (see page 21)
∗1: The wire size in ( ) does not comply with JIS standards. ∗2: The rated current differs according to operating conditions. See “Selecting Terminal Blocks by Current According to JIS Standards” on page 4. ∗3: Use a CSA certified crimping terminal when using the terminal block as a CSA certified product.
10
BN-W / BNH-W Series Terminal Blocks M6
132A
BN100W
M8
Dimensions Dust Cover (BNC420)
63 33
16.7 53
35 29
26
29.8 26 23
When using DIN Rail: 52 When using C Rail: 58 50.5
22.5 20 17
41.5 18.2
44.2 (when using BNCA, BNCP: 50)
Screw Terminal
Large Capacity
94A
BN75W
Part No.
BAA1000
BN75WPN10
Ordering No.
10
5
Weight (Approx.)
45g
86g
Standards Insulation Voltage Specification / Ratings
BN100WPN05
Package Quantity
Wire Size Rated Current ∗1 Terminal screw ∗2 Crimping Terminal
UL/CSA
EN
JIS
UL/CSA
EN
JIS
600V
660V
600V
600V
660V
600V
16-4 AWG
22 mm2 (8-4 AWG)
22 mm2
16-2 AWG
38 mm2 (2AWG)
38 mm2
80A
94A
94A
100A
132A
132A
M6
M8
2-6 to 22-6
2-8 to 38-8
Max. No. of Crimping Terminals Socket Wrench Tightening Torque
2
2
12.7 mm square drive hexagonal socket 10
12.7 mm square drive hexagonal socket 13
3.9 to 5.4 N · m
10 to 13.5 N · m ø8.5 min.
ø6.2 min.
Accessories
Crimping Terminal Dimensions (mm) ∗3
22.8 max.
16.8 max. 8.5 max.
6 min.
11 max.
10 min.
End Plate
BNE75W (see page 20)
BNE100W (see page 20)
Dust Cover
BNC420 (see page 21)
BNC520 (see page 21)
Marking Strip Marking Strip Fastner DIN Rail/End Clip Type C Rail/End Clip DIN+Type C Rail/End Clip
PVC 1m/BNM7, Fiber glass 1m/BNM9, PVC 25m/BNM725 (see page 22) BNM3 (see page 22) Aluminum: BAA1000, Steel: BAP1000 (see page 20)/BNL8 (see page 21) Aluminum: B NCA1000, Steel: BNCP1000 (see page 20)/BNL8 (see page 21) Aluminum: BNJA1000 (see page 20)/BNL8 (see page 21)
∗1: The rated current differs according to operating conditions. See “Selecting Terminal Blocks by Current According to JIS Standards” on page 4. ∗2: The grooves on the head of the hex bolt are for temporary tightening. For proper tightening, use an applicable socket wrench and tighten within the range of the recommended tightening torque. ∗3: Use a CSA certified crimping terminal when using the terminal block as a CSA certified product.
11
BN-W / BNH-W Series Terminal Blocks 175A
BN150NW
M8
M8
Dimensions
29.8 26 23
74 63 33
7.5
21.5
50.5
29.8 26 23
6
35 29
When using DIN Rail: 52 (when using C Rail: 58)
74 63 33
When using DIN Rail: 52 When using C Rail: 50 50.5
Screw Terminal
Large Capacity
175A
BN150W
Part No.
35mm DIN Rail
BN150WPN05
Ordering No. Packaging Quantity Weight (Approx.) Standards Specification / Ratings
Insulation Voltage Wire Size Rated Current ∗1 Terminal screw ∗2 Crimping Terminal Max. No. of Crimping Terminals Socket Wrench Tightening Torque
BN150NWPN05
5
5
88g
95g
UL/CSA
EN
JIS
—
—
JIS
600V
660V
660V
—
—
600V
16-1/0 AWG
60 mm2 (1/0 AWG)
60 mm2
—
—
60 mm2
150A
175A
175A
—
—
175A
M8
M8
2-8 to 60-8
2-8 to 60-8
2
2
12.7 mm square drive hexagonal socket 13 (∗2) 10 to 13.5 N · m
12.7 mm square drive hexagonal socket 13 (∗2) 10 to 13.5 N · m ø8.5 min.
Crimping Terminal Dimensions (mm) ∗3
End Plate
22.8 max. 11 max.
BNE150W (see page 20)
Accessories
Dust Cover Marking Strip Marking Strip Fastner DIN Rail/End Clip Type C Rail/End Clip DIN+Type C Rail/End Clip
10 min.
BNC520 (see page 21) PVC 1m/BNM7, Fiber glass 1m/BNM9 PVC 25m/BNM725 (see page 22)
PVC 1m/BNM7, Fiber glass 1m/BNM9 PVC 25m/BNM725 (see page 22) BNM3 (see page 22)
Aluminum BAA1000, Steel: BAP1000 (see page 20)/ BNL8 (see page 21) Aluminum: BNCA1000, Steel: BNCP1000 (see page 20)/ BNL8 (see page 21) Aluminum: BNJA1000 (see page 20)/BNL8 (see page 21)
∗1: The rated current differs according to operating conditions. See “Selecting Terminal Blocks by Current According to JIS Standards” on page 4. ∗2: The grooves on the head of the hex bolt are for temporary tightening. For proper tightening, use an applicable socket wrench and tighten within the range of the recommended tightening torque. ∗3: Use a CSA certified crimping terminal when using the terminal block as a CSA certified product. ∗4: Applicable wrench or screwdriver can be used for tightening screws.
12
BN-W / BNH-W Series Terminal Blocks 240A
BN200BW
Part No.
BN200BWK
M10
240A
Surface Mount
M10
Panel Cut-out
100 (2P) 137 (3P) 174 (4P)
Dimensions
Large Capacity
90 (between terminal screws: 46)
Hexagonal bolt M10×19 Dust Cover
1.5
37
Dust Cover
1.5
78 (2P), 115 (3P), 152 (4P)
90 (between terminal screws: 46)
33
78 (2P), 115 (3P), 152 (4P) 37
Hexagonal Bolt M10×20
4
3-ø8 Hole
34
34
65
30 46
100 (2P), 137 (3P), 174 (4P)
8
Package Quantity
1
1
Weight (Approx.)
2P: 430g, 3P: 650g, 4P: 870g
2P: 490g, 3P: 710g, 4P: 930g
240A
BN200NW
Part No.
33
4 66.5 65
66.5 (all rail types)
Screw Terminal
30
4-M6 Screw
BN200NWK
M10
240A
8
Surface Mount
M10
Panel Cut-out
30
4-M6 Screw
Dimensions
90 (between terminal screws: 46)
90 (between terminal screws: 46) Dust Cover
33
4
Bolt M10
37
34
100 (2P), 137 (3P), 174 (4P)
8
Package Quantity
1
1
2P: 500g, 3P: 720g, 4P: 940g
2P: 560g, 3P: 780g, 4P: 1000g
Insulation Voltage Wire Size Rated Current ∗1 Terminal Screw ∗2 Crimping Terminal Max. No. of Crimping Terminals
Socket Wrench Tightening Torque
4
34
30
Weight (Approx.) Standards
33
3-ø8 Hole
46
Specification / Ratings
78 (2P), 115.0 (3P), 152 (4P)
Dust Cover
66.5 65
Bolt M10
37
1.5
78 (2P), 115.0 (3P), 152 (4P)
65
66.5 (all rail types)
1.5
Stud Terminal
100 (2P) 137 (3P) 174 (4P)
UL/CSA
EN
JIS
UL/CSA
EN
JIS
600V
660V
600V
600V
660V
600V
4/0 AWG
100 mm2 (4/0 AWG)
100 mm2
4/0 AWG
100 mm2 (4/0 AWG)
100 mm2
200A
240A
240A
200A
240A
240A
M10
M10
5.5-10 to 100-10
5.5-10 to 100-10
2
2
12.7 mm square drive hexagonal socket 17 (∗2) 21 to 28 N·m
12.7 mm square drive hexagonal socket 17 (∗2) 21 to 28 N·m
8
ø10.5 min.
Crimping Terminal Dimensions (mm) ∗3
Accessories
Accessories (Supplied) DIN Rail C Rail DIN+C Rail End Clip
32.8 max. 16 max.
11 min.
End Plate, Dust Cover (see page 20, 21), Marking Strip (see page 22) are supplied. (Note) Marking Strip Fastener (BNM3) is not necessary. Aluminum: BAA1000, Steel: BAP1000 (see page 20)
—
Aluminum: BNCA1000, Steel: BNCP1000 (see page 20)
—
Aluminum: BNJA1000 (see page 20)
—
BNL8 (see page 21)
—
∗1: The rated current differs according to operating conditions. See “Selecting Terminal Blocks by Current According to JIS Standards” on page 4. ∗2: The grooves on the head of the hex bolt are for temporary tightening. For proper tightening, use an applicable socket wrench and tighten within the range of the recommended tightening torque. ∗3: Use a CSA certified crimping terminal when using the terminal block as a CSA certified product. Specify the number of poles in place of . 2-pole: 2, 3-pole: 3, 4-pole: 4.
13
BN-W / BNH-W Series Terminal Blocks 310A
BN300BW
Part no.
BN300BWK
M10
310A
Surface Mount
M10
Panel Cut-out
30
4-M6 Screw
Dimensions
4
44 40.5
Hexagonal Bolt M10×22
4
3-ø8 Hole
74
37
Hexagonal Bolt M10×22
44 40.5
75.5 74
Dust Cover
Dust Cover
1.5
92 (2P), 136 (3P), 180 (4P)
104 (between terminal screws: 50)
30
37
75.5 (all rail types)
Large Capacity
92 (2P), 136 (3P), 180 (4P)
104 (between terminal screws: 50)
1.5
Screw Terminal
114 (2P) 158 (3P) 202 (4P)
114 (2P), 158 (3P), 202 (4P)
8
46
Package Quantity
1
1
Weight (Approx.)
2P: 480g, 3P: 750g, 4P: 1020g
2P: 540g, 3P: 810g, 4P: 1080g
310A
BN300NW
Part no.
BN300NWK
M10
310A
8
Surface Mount
M10
Panel Cut-out
30
4-M6 Screw
Dimensions
Dust Cover
1.5
Dust Cover
4
Bolt M10
114 (2P), 158 (3P), 202 (4P)
8
1
1
2P: 540g, 3P: 810g, 4P: 1080g
2P: 600g,3P: 870g, 4P: 1140g
Wire Size Rated Current ∗1 Terminal Screw ∗2 Crimping Terminal Max. No. of Crimping Terminals
Socket Wrench Tightening Torque
4
37
37
30
46
Package Quantity
Insulation Voltage
44 40.5
3-ø8 Hole
75.5 74
Bolt M10
44 40.5
74
75.5 (all rail types)
92 (2P), 136 (3P), 180 (4P)
92 (2P), 136 (3P), 180 (4P)
Weight (Approx.) Standards Specification / Ratings
104 (between terminal screws: 50)
104 (between terminal screws: 50) 1.5
Stud Terminal
114 (2P) 158 (3P) 202 (4P)
UL/CSA
EN
JIS
UL/CSA
EN
JIS
600V
660V
600V
600V
660V
600V
300 MCM
150 mm2 (300 MCM)
150 mm2
300 MCM
150 mm2 (300 MCM)
150 mm2
310A
310A
310A
310A
310A
310A
M10
M10
5.5-10 to 150-10
5.5-10 to 150-10
2
2
12.7 mm square drive hexagonal socket 17 (∗2) 21 to 28 N·m
12.7 mm square drive hexagonal socket 17 (∗2) 21 to 28 N·m
8
ø10.5 min.
Crimping Terminal Dimensions (mm) ∗3
Accessories
Accessories (Supplied) DIN Rail C Rail DIN+C Rail End Clip
39.8 max. 20 max.
11 min.
End Plate, Dust Cover (see page 20, 21), Marking Strip (see page 22) are supplied. (Note) Marking Strip Fastener (BNM3) is not necessary. Aluminum: BAA1000, Steel: BAP1000 (see page 20)
—
Aluminum: BNCA1000, Steel: BNCP1000 (see page 20)
—
Aluminum: BNJA1000 (see page 20)
—
BNL8 (see page 21)
—
∗1: The rated current differs according to operating conditions. See “Selecting Terminal Blocks by Current According to JIS Standards” on page 4. ∗2: The grooves on the head of the hex bolt are for temporary tightening. For proper tightening, use an applicable socket wrench and tighten within the range of the recommended tightening torque. ∗3: Use a CSA certified crimping terminal when using the terminal block as a CSA certified product. Specify the number of poles in place of . 2-pole: 2, 3-pole: 3, 4-pole: 4.
14
BN-W / BNH-W Series Terminal Blocks 370A
BN400BW
Part no.
BN400BWK
M12
370A
Surface Mount
M12
Panel Cut-out
30
4-M6 Screw
Dimensions
120 (between terminal screws: 62)
120 (between terminal screws: 62)
Large Capacity
57
Hexagonal Bolt M12×25
38.1
38.1
30
142 (2P), 199 (3P), 256 (4P)
8
8
46
Package Quantity
1
1
Weight (Approx.)
2P: 950g, 3P: 1400g, 4P: 1860g
2P: 1030g, 3P: 1480g, 4P: 1940g
370A
BN400NW
Part No.
5
52
3-ø8 Hole
5 81.5 80
1.5
Dust Cover
1.5
119 (2P), 176 (3P), 233 (4P) 57 Hexagonal Bolt 52 M12×23
119 (2P), 176 (3P), 233 (4P)
Dust Cover
80
81.5 (all rail types)
Screw Terminal
142 (2P) 199 (3P) 256 (4P)
BN400NWK
M12
370A
Surface Mount
M12
Panel Cut-out
30
4-M6 Screw
Dimensions
120 (between terminal screws: 62)
120 (between terminal screws: 62)
52
57
52
5
38.1
38.1
81.5 80
Bolt M12 3-ø8 Hole
5 81.5 80
Bolt M12
57
119 (2P), 176 (3P), 233 (4P)
Dust Cover
1.5
119 (2P), 176 (3P), 233 (4P)
Dust Cover
1.5
Stud Terminal
142 (2P) 199 (3P) 256 (4P)
30
142 (2P), 199 (3P), 256 (4P)
8
8
46
Package Quantity
1
1
Weight (Approx.)
2P: 980g, 3P: 1460g, 4P: 1930g
2P: 1060g, 3P: 1540g, 4P: 1990g
Standards Specification / Ratings
Insulation Voltage Wire Size Rated Current ∗1 Terminal Screw Crimping Terminal Max. No. of Crimping Terminals
Socket Wrench Tightening Torque
UL/CSA
EN
JIS
UL/CSA
EN
JIS
600V
660V
600V
600V
660V
600V
400 MCM
200 mm2 (400 MCM)
200 mm2
400 MCM
200 mm2 (400 MCM)
200 mm2
350A
370A
370A
350A
370A
370A
M12
M12
14-12 to 200-12
14-12 to 200-12
2
2
12.7 mm square drive hexagonal socket 19 (∗2) 38 to 49 N·m
12.7 mm square drive hexagonal socket 19 (∗2) 38 to 49 N·m ø12.5 min.
Crimping Terminal Dimensions (mm) ∗3
Accessories
Accessories (Supplied) DIN Rail C Rail DIN+C Rail End Clip
50.8 max. 26 max.
14 min.
End Plate, Dust Cover (see page 20, 21), Marking Strip (see page 22) are supplied. (Note) Marking Strip Fastener (BNM3) is not necessary. Aluminum: BAA1000, Steel: BAP1000 (see page 20)
—
Aluminum: BNCA1000, Steel: BNCP1000 (see page 20)
—
Aluminum: BNJA1000 (see page 20)
—
BNL8 (see page 21)
—
∗1: The rated current differs according to operating conditions. See “Selecting Terminal Blocks by Current According to JIS Standards” on page 4. ∗2: The grooves on the head of the hex bolt are for temporary tightening. For proper tightening, use an applicable socket wrench and tighten within the range of the recommended tightening torque. ∗3: Use a CSA certified crimping terminal when using the terminal block as a CSA certified product. Specify the number of poles in place of . 2-pole: 2, 3-pole: 3, 4-pole: 4.
15
BN-W / BNH-W Series Terminal Blocks Part No
430A
BN500BWK
Surface Mount
M16
—
Panel Cut-out
60
4-ø9
—
Dimensions 152 (between terminal screws: 62)
119 (2P), 176 (3P), 233 (4P) 57 52 Bolt M16
1.5
Dust Cover
5
2-ø9 Hole
Large Capacity Surface Mount
42.5
91.5 90
Screw Terminal
162 (2P) 219 (3P) 276 (4P)
8.5
60 80
162 (2P), 219 (3P), 276 (4P)
Package Quantity
1
Weight (Approx.)
2P: 1550g, 3P: 2250g, 4P: 2950g
Part No.
—
430A
BN500NWK
8.5
— Surface Mount
M16
BN600NWK
520A
Surface Mount
M16
Panel Cut-out
Panel Cut-out 4-ø9
60
60
4-ø9
162 (2P) 219 (3P) 276 (4P)
Dimensions Dust Cover
1.5
152 (between terminal screws: 62)
119 (2P), 176 (3P), 233 (4P) 57 52 Bolt M16
5
43.5
42.5 60 80
60 80
8.5
8.5
162 (2P), 219 (3P), 276 (4P)
1
1
Weight (Approx.)
2P: 1600g, 3P: 2300g, 4P: 3000g
2P: 1650g, 3P: 2400g, 4P: 3150g
Insulation Voltage Specification / Ratings
162 (2P), 219 (3P), 276 (4P)
8.5
Package Quantity Standards
Wire Size Rated Current ∗1 Terminal Screw ∗2 Crimping Terminal Max. No. of Crimping Terminals
Socket Wrench Tightening Torque
5
2-ø9 Hole
91.5 90
2-ø9 Hole
119 (2P), 176 (3P), 233 (4P) 57 52 Bolt M16
Dust Cover
1.5
152 (between terminal screws: 62)
91.5 90
Stud Terminal
162 (2P) 219 (3P) 276 (4P)
UL/CSA
EN
JIS
UL/CSA
EN
JIS
600V
660V
600V
600V
660V
600V
500 MCM
240 mm2 (500 MCM)
250 mm2
600 MCM
300 mm2 (600 MCM)
325 mm2
500A
430A
430A
600A
520A
520A
M16
8.5
M16
14-16 to 200-16
325-16
14-16 to 200-16
325-16
2
1
2
1
12.7 mm square drive hexagonal socket 24 (∗2) 83 to 116 N·m
12.7 mm square drive hexagonal socket 24 (∗2) 83 to 116 N·m ø16.5 min.
Crimping Terminal Dimensions (mm) ∗3
Accessories (Supplied)
50.8 max. 26 max.
16 min.
End Plate, Dust Cover (see page 20, 21), Marking Strip (see page 22) are supplied. (Note) Marking Strip Fastener (BNM3) is not necessary.
∗1: The rated current differs according to operating conditions. See “Selecting Terminal Blocks by Current According to JIS Standards” on page 4. ∗2: The grooves on the head of the hex bolt are for temporary tightening. For proper tightening, use an applicable socket wrench and tighten within the range of the recommended tightening torque. ∗3: Use a CSA certified crimping terminal when using the terminal block as a CSA certified product. Specify the number of poles in place of . 2-pole: 2, 3-pole: 3, 4-pole: 4.
16
BN-W / BNH-W Series Terminal Blocks
Notes: UL/CSA approved products shown below are not supplied with fuses. When UL/CSA approval is required for fuse terminal blocks, use UL/ CSA-rated fuses. • Part No.: BNF10SW • Rated Insulation Voltage: 600V • Rated Current: 10A • Applicable Wire: 18-10 AWG • UL File No.: E78117 • CSA File No.: LR64803 BNF10S-APN20
10A
M4
• Internal Connection Fuse
33 27
Neon Lamp
Notes: • Rated Current: 20A • This terminal block cannot be used as a disconnect switch. • When switching on/off, make sure that voltage is not applied.
Notes: Neon lamp turns on when the fuse blows. For the neon lamp to turn on, the voltages must be from 100 to 250V AC. Fuse Ratings • Rated Voltage: 250V • Rated Current: 1, 3, 5A • Cartridge Fuse: JIS C 6575-2 6.35×31.8mm or 6.40×30.0mm • Part No.: BNF10N-1A BNF10N-3A BNF10N-5A
OFF
ON
Terminal Screw Terminal Screw
BNF10N-APN20
Ordering No.
BNT20PN20 20 36g
20
20
Package Quantity
Weight (Approx.)
34g
34g
Weight (Approx.)
Specification / Ratings
17.5 15 13
When using C Rail: 50 42.5
When using DIN Rail: 44
Self-Lifting Terminal with Disconnecting Switch
33 27
When using C Rail: 59.5 52
63 43
Package Quantity
Standards
JIS
JIS
600V
600V
Wire Size
5.5 mm2
5.5 mm2
Rated Current
10A max.
20A
Terminal Screw
M4
M4
1.25-4 to 5.5-4
1.25-4 to 5.5-4
Insulation Voltage
Crimping Terminal Max. No. of Crimping Terminals Tightening Torque
M4
20A
BNT20
17.5 15 13
63 43 When using DIN Rail: 53.5
33 27
When using C Rail: 59.5 52
When using DIN Rail: 53.5
Fuse Ratings • Rated Voltage: 250V • Rated Current: 1, 3, 5A • Cartridge Fuse: JIS C 6575-2 6.35×31.8 mm or 6.40×30.0 mm • Part No.: BNF10S-1A BNF10S-3A BNF10S-5A • Cartridge used: FGB1 by FUJI Terminal Industry Co., Ltd.
Ordering No.
BNF10N (With Lamp)
17.5 15 13
63 43
Self-Lifting Terminal with Fuse
M4
10A
BNF10S
2
2
1.4 to 2.0 N·m
1.4 to 2.0 N·m ø4.2 min.
Crimping Terminal Dimensions (mm)
11.3 max. 5.2 max.
Accessories
End Plate Dust Cover Marking Strip DIN Rail/End Clip C Rail/End Clip DIN+C Rail/End Clip
5 min.
BNE20 (see page 20) —
BNC520 (see page 21)
—
PVC 1m/BNM7, Fiber glass 1m/BNM9 PVC 25m/BNM725 (see page 22)
Aluminum: BAA1000, Steel: BAP1000 (see page 20) /BNL6 (see page 21) Aluminum: BNCA1000, Steel: BNCP1000 (see page 20) /BNL6 (see page 21) Aluminum: BNJA1000 (see page 20) /BNL6 (see page 21)
17
BN-W / BNH-W Series Terminal Blocks M3
16A
13.5 12 8 6.7
62
Dimensions
38 18
M3.5
21A
BND15LW
62.2 (when using C Rail: 68) 59.5 42 18.5
8.5 10.5
BND15WPN25
BND15LWPN25
Package Quantity
25
25
25
Weight (Approx.)
16g
23g
17g
Ordering No.
M3
16A
BNDH15W
38 18
BND15WTPN25
M3.5
21A
BNDH15LW
13.5 12 8 6.7
62
Dimensions
21A
BNDH15WT
38 18
38 17.5
8.5 10.5
6.7 8
BNDH15WPN25
BNDH15LWPN25
Package Quantity
25
25
25
Weight (Approx.)
17g
26g
17g
Standards Insulation Voltage Wire Size Rated Current ∗1 Terminal Screw ∗2 Crimping Terminal
EN
JIS
UL/CSA
EN
JIS
UL/CSA
EN
JIS
600V
660V
600V
600V
660V
600V
600V
660V
600V
22-14 AWG
2 mm2 (22-14 AWG)
1.25 mm2 (2 mm2 max)
22-14 AWG
2 mm2 (22-14 AWG)
2 mm2
22-14 AWG
2mm2 (22-14 AWG)
2 mm2
10A
22A
16A
15A
22A
21A
15A
22A
21A
M3
M3.5
M3.5
1.25-3 (2-3)
2-3.5
1.25-3.5 to 2-3.5
2
2
2
0.6 to 1 N·m
1 to 1.3 N·m
1.0 to 1.3 N·m
ø3.6 min.
ø3.2 min.
Crimping Terminal (mm) ∗3
6.6 max. 5 max.
End Plate Dust Cover Marking Strip
BNDH15WTPN25
UL/CSA
Max. No. of Crimping Terminals
Tightening Torque
5 max.
BNDE15W/BNDE15W2 (see page 20)
6.6 max. 4 min.
BNDE15LW/BNDE15LW2 (see page 20)
BNM3 (see page 22)
DIN+C Rail/End Clip
3.6 min.
Upper Deck: BNC230, Lower Deck: BNC240 (see page 21)
BNDL2 (see page 24)
C Rail/End Clip
4.7 max.
BNDE15W/BNDE15W2 (see page 20)
PVC 1m/BNM7, Fiber glass 1m/BNM9, PVC 25m/BNM725 (see page 22)
Surface Mounting Clip
DIN Rail/End Clip
ø3.6 min.
8.5 max.
3.3 min.
Marking Strip Fastener Connecting Rod/ Connecting Nut
M3.5
13.5 12 8 6.7
62
17.3 15.8 10.5 8.5
62
62.2 (when using C Rail: 68) 59.5 42 18.5
61.2 (when using C Rail: 67) 58.5 42 18.5
Touch-Down Terminal
Part No.
Ordering No.
Specification / Ratings
6.7 8
61.2 (when using C Rail: 67) 58.5 42 18.5
Double-Deck Terminal Block
6.7 8
6.7 8
Accessories
13.5 12 8 6.7
62 38 17.5
17.3 15.8 10.5 8.5
62 38 18
M3.5
21A
BND15WT
61.2 (when using C Rail: 67) 58.5 42 18.5
BND15W
61.2 (when using C Rail: 67) 58.5 42 18.5
Self-Lifting Terminal
Part No.
Connecting Rod: BNR1, BNR2, Connecting Nut: BNN1 (see page 24) Aluminum: BAA1000, Steel: BAP1000 (see page 20)/BNL6 (see page 21) Aluminum: BNCA1000, Steel: BNCP1000 (see page 20)/BNL7 (see page 21) Aluminum: BNJA1000 (see page 20)/BNL6, BNL7 (see page 21)
∗1: The rated current differs according to operating conditions. See “Selecting Terminal Blocks by Current According to JIS Standards” on page 4. ∗2: The grooves on the head of the hex bolt are for temporary tightening. For proper tightening, use an applicable socket wrench and tighten within the range of the recommended tightening torque. ∗3: Use a CSA certified crimping terminal when using the terminal block as a CSA certified product.
18
BN-W / BNH-W Series Terminal Blocks BN15MC4 16A (common current)
Part No. No. of Poles
M3
BN15MC8 16A (common current)
4
M3
BN15MC10 16A (common current)
8
M3
10
Shape
Self-Lifting Terminal
Terminal
Terminal
Common
Common
Terminal
Terminal
37 (4P), 69 (8P) 85 (10P) 38 18
6.7
Jumper side: 24.1 Jumper side: 30.1
29.5 23.5
8
Dimensions
BN15MC4PN10
BN15MC8PN10
Package Quantity
10
10
10
Weight (Approx.)
30g
57g
70g
Light Gray
Light Gray
Light Gray
Ordering No.
Color Standards Specification / Ratings
Common
Terminal
When using DIN Rail: 35 When using C Rail: 41 32.5
Common Terminal
Terminal
BN15MC10PN10
JIS
Insulation Voltage
600V 1.25 mm2 (2 mm2 max.)
Wire Size Rated Current
16A/Common Current
Terminal Screw
M3
Crimping Terminal
1.25-3 (2-3)
Max. No. of Crimping Terminals
2
Tightening Torque
0.6-1.0 N·m ø3.2 min.
Crimping Terminal Dimensions (mm)
6.6 max. 5 max.
Accessories
End Plate
3.3 min.
Supplied
Dust Cover
BNC230 (see page 21)
Marking Strip
PVC 1m/BNM7, Fiber glass 1m/BNM9, PVC 25m/BNM725 (see page 22)
Marking Strip Fastener
BNM3 (see page 22)
DIN Rail / End Clip
Aluminum: BAA1000, Steel: BAP1000 (see page 20)/BNL6 (see page 21)
C Rail / End Clip
Aluminum: BNCA1000, Steel: BNCP1000 (see page 20)/BNL7 (see page 21)
DIN+C Rail / End Clip
Aluminum: BNJA1000 (see page 20)/BNL6, BNL7 (see page 21)
Note1: The rated applicable wire size is 1.25 mm2, but 2 mm2 wires can also be connected. The wire size in ( ) does not comply with JIS standards. Note2: Do not remove the built-in common jumper. Common terminal type terminal blocks cannot be disassembled. Note3: Make sure that all terminal screws are tightened to an appropriate tightening torque before power is applied. Note4: Specifications are in compliance with JIS C 2811 except values in ( ).
Application Example
Features
BN15MC4 T
U CP
PLC
IN
OU
L0 L1 L2 L3 L4 L5 L6 L7
(+) (–)
•• All terminals are short-circuted by a built-in common jumper. External jumpers are not required. •• Accessories (marking strip, cover, and rails) are compatible with standard types. •• Common terminal type terminal blocks can be combined with other standard types as they are identical in shape and in size as BN15MW. •• Color: Light Gray
L0 to L7: Load
19
BN-W / BNH-W Series Terminal Blocks Accessories (End Plate / Rail) End Plates Used for ends of terminal blocks. Also used to hold the marking strips in place. 63
5
3
BNE15W
5
5
BNE20
Part No.
5
BNE150W
End Plate
Securing a marking strip with the end plate
End Plate for Securing End Plate
5
BNE40W
BNE50W
BNDE15W Upper deck: 5 mm Lower deck: 9 mm
BNDE15W2 Upper deck: 5.5 mm Lower deck: 1.5 mm
BDNE15LW Upper deck: 5 mm Lower deck: 10.25 mm
BDNE15LW2 Upper deck: 6.8 mm Lower deck: 1.5 mm
BNDE15W BDNE15LW
BNE100W
74
48
62
62
5
BNE75W
5
BNE30W
63
53
43
38
38
BNDE15W2 BNDE15LW2 Applicable Terminal Blocks BN10W, BNH10W BN15MW, BNH15MW BN15LW, BNH15LW BN15MWT, BNH15MWT BN15LWT, BNH15LWT BNT20, BNF10S, BNF10N BN30W, BNH30W BN40W, BNH40W BN50W, BNH50W BN75W BN100W BN150W, BN150NW BND15W, BND15WT, BNDH15W, BNDH15WT
Ordering No.
BNE15W
BNE15WPN10
BNE20 BNE30W BNE40W BNE50W BNE75W BNE100W BNE150W
BNE20PN10 BNE30WPN10 BNE40WPN10 BNE50WPN10 BNE75WPN10 BNE100WPN10 BNE150WPN10
BNDE15W
BNDE15WPN10
BNDE15LW
BNDE15LWPN10
BND15LW, BNDH15LW
BNDE15W2
BNDE15W2PN10
BND15W, BND15WT, BNDH15W, BNDH15WT
BNDE15LW2 BNDE15LW2PN10
BND15LW, BNDH15LW
Thickness (mm)
Weight (Approx.)
5.0
4g
3.0 5.0 5.0 5.0 5.0 5.0 5.0 Upper deck: 5.0 Lower deck: 9.0 Upper deck: 5.0 Lower deck: 10.25 Upper deck: 5.5 Lower deck: 1.5 Upper deck: 6.8 Lower deck: 1.5
8g 4g 5g 6g 6g 9g 10g
Package Quantity
10
5.5g 6g 5.5g 6g
Note: BNDE15W2 and BNDE15LW2 are end plates used for securing marking strips at the end of double deck terminal blocks.
Rails Rails for mounting terminal blocks. Available in five styles.
BNCA BNCP
Length
1000 mm
20
Part No. BNCA1000 BNCP1000 BAA1000 BAP1000 BNJA1000
Ordering No. BNCA1000PN10 BNCP1000PN10 BAA1000PN10 BAP1000PN10 BNJA1000PN10
12.5 12.5
8
25
BAA:31 BAP:27 BAA BAP
Material Aluminum Steel Aluminum Steel Aluminum
16 30 35 15.5
7.5
35
2
16 30
BAA:1.7 BAP:1
12.5
BNJA
1.5
BAA BAP
15
BNCA BNCP
5.5
12.5 12.5
8
5.5
8
5.5
Approvals: IEC60715 JIS C 2812
DIN 35-mm + C30 Rail
21.5
DIN Rail 35-mm-wide
C30 Rail
25 BNJA
Weight (Approx.) 260g 700g 200g 320g 340g
Package Quantity 10 10 10 10 10
BN-W / BNH-W Series Terminal Blocks Accessories (End Clip / Rail Mounting Clip / Dust Cover) End Clips Used to secure the ends of the terminal blocks assembled on the rail.
23.4
24 45
28
9
BNL6 (M4 Screw) Tightening torque: 1.1 N·m
32.5 46
12.1
14.4
BNL7 (M4 Screw)
• Material: Steel • Plating: Trivalent zinc chromate
BNL8 (M4 Screw)
Note: Slide the end clip onto the DIN rail. Part No.
For Terminal Blocks up to BND and BN40 BAA, BAP × BNCA, BNCP, BNJA × BAA, BAP, BNCA, — (∗1) BNCP, BNJA
Ordering No.
BNL6 BNL7
BNL6PN10 BNL7PN10
BNL8
BNL8PN10
× (∗2) × (∗2)
For Terminal Blocks BN100 and larger — —
×
×
For BN50 and BN75
Rails
Weight (Approx.)
Package Quantity
15.2g 16g
10 10
56g
10
∗1: Do not use BNL8 because the insulation distance will be insuffiecient if used. ∗2: We recommend you to use BNL8 for secure hold.
Rail Mounting Clips Used to raise the DIN rail from the panel surface. 2-ø5.2
12.5
2-M5
2.6
28
15
28
12.5
12.5
BNS3
Dust Cover
BNC230
1m
Ordering No.
BNS3 BNS4
BNS3PN10 BNS4PN10
Weight (Approx.) 51.3g 76.2g
Package Quantity 10 10
• Material: Steel • Plating: Trivalent zinc chromate
BNS4
Material: Polycarbonate
BNC330
Length Width (mm)
Part No.
12.5
15
2.6
2-M5
30
54
15
25°
54
26
15
76.7
30
2-ø5.2
25°
26
36.7
BNC320
Part No.
BNC420
BNC520
Ordering No.
BAC820
BNC1000
BNC930
BNC240
Weight (Approx.) Package Quantity
Terminal Blocks (: No. of Poles)
39.6
BNC230
BNC230PN10
BN10W, BNH10W, BN15MW, BNH15MW, BN15LW, BNH15LW, BN30W, BNH30W, BN15MWT, BNH15MWT, BN15LWT, BNH15LWT
43 49.6 54.6 65 82 96 110 145
BNC330 BNC320 BNC420 BNC520 BAC820 BNC910 BNC1000 BNC930
BNC330PN10 BNC320PN10 BNC420PN10 BNC520PN10 BAC820PN10 BNC910PN10 BNC1000PN10 BNC930PN10
BN40W, BNH40W BN50W, BNH50W BN75W BN150W, BN150NW, BNT20, BN100W BN200BW(K), BN200NW(K) BN300BW(K), BN300NW(K) BN400BW(K), BN400NW(K) BN500BW(K), BN500NW(K), BN600NW(K)
56g
10
57g 64g 72g 96g 204g 222g 256g 310g
10 10 10 10 10 10 10 10
Dust Covers for Double Deck Terminal Blocks Length 1m
Part No.
Ordering No.
Upper Deck BNC230
BNC230PN10
Lower Deck BNC240
BNC240PN10
Terminal Block BND15W, BNDH15W, BND15LW, BNDH15LW, BND15WT, BNDH15WT
Weight (Approx.)
Package Quantity
56g
10
15g
10
21
BN-W / BNH-W Series Terminal Blocks Accessories (Marking Strips / Marking Strip Fastener / Slide Marking Strip) Marking Strips, Marking Strip Fastener Item
Part No. Ordering No. BNM7
BNM7PN10
7.2g
10
BNM9
BNM9PN10
6.4g
10
BNM725
BNM725
—
1
BNM3
BNM3PN50
0.1g
50
Marking Strip BNM7
BNM9
BNM3
Weight Package (approx.) Quantity
Marking Strip Fastener
Specification PVC (glossy surface) 1000 mm × 9.5 mm × 0.5 mm Fiber glass (matte surface) 1000 mm × 9.5 mm × 0.5 mm PVC (matte surface) 25 m × 9.5 mm × 0.5 mm
•• To install the marking strip fastener
9.5
ø75mm
160mm
Sliding Marking Strip (BN10W to BN30W)
17-mm-wide Marking Strip
Marking Strip Holder
17-mm-wide marking strip
•• Both top and bottom sides of the marking strip holder can be used.
End plate (Thickness 5 mm) BNES15W BNES30W
Terminal Block BN10W to BN15LWT BN30W Item
Part No. BNES15W ➀ End Plate BNES30W BNM5 ➁ Marking Strip ➂ Marking Strip Holder BNMH1 BNCS230 ➃ Dust Cover
Ordering No. BNES15WPN10 BNES30WPN10 BNM5PN10 BNMH1PN10 BNCS230PN10
Terminal Blocks BN10W to BN15LWT BN30W BN10W to BN15LWT BN30W
Specification For sliding marking strip For sliding marking strip PVC (Note) 1m 1m
Package Quantity 10 10 10 10 10
Note: Length 1000 mm × Width 9.5 mm × Thickness 0.5 mm
Installing the Sliding Marking Strip 1. Insert the marking strip into the groove of the top of the marking strip holder.
3. Insert the marking strip holder into the recess of the end plate.
3 Marking Strip Holder
3 Marking Strip Holder 2 Marking Strip Marking Strip
Recess
Movement •• Sliding movement of the marking strip holder Slide When sliding the mark ing strip holder, slide by holding both edges of the holder.
Recess
2. Installing the end plate Attach the end plates to the terminal blocks and secure with end clips.
4 Dust Cover
• To lock the marking strip holder Lock
4. Press the dust cover to fit onto the bottom groove of the end plate.
1 End Plate End Clip (BNL6)
22
To lock the marking strip holder, lock by holding both edges of the holder.
BN-W / BNH-W Series Terminal Blocks Accessories (Jumper) Jumpers for 6 Poles (Material: Brass, Plating: Nickel-plated, Insulation: PVC) Part No.
Ordering No.
Terminal Centers
Insulation Ring Terminal Without
With 7 mm
BNJ16FPN10
Insulation
10
10
Fork Terminal
10A
35 (6-pole)
7
5.7 R1 3.7 .85
Without
BN10W BNH10W 10
1.4 0.8
With
2
11
BNJ16FBPN10
2.7g 10 Insulation
4
BNJ16FB
Ring Terminal Without
BNJ26WBPN10
With 8 mm
BNJ26FWPN10
0.8
2
Insulation
Fork Terminal
20A
40 (6-pole)
8
R1 6.4 .8 5
Without
10
1.4
1.4
3.7
0.8
With
Without
8.2
52.5 (6-pole)
10.5
With 10.5 mm Without
BNJ46FB
BNJ46FBPN10
With
8.2 R2 .1
1.4
10
2.8
3.0g
1.4
10
0.8
3.2g
1.7
With
60 (6-pole)
12
.2
BNJ56BPN10
9.3
ø4
BNJ56B
10
10
5.5
Without
BN15LW BNH15LW BN15LWT BNH15LWT BND15LW BNDH15LW
Insulation
9.5
BNJ56PN10
20A 0.8
Ring Terminal BNJ56
4.6g
52.5 (6-pole)
10.5 4.2
11 4.5
BNJ46FPN10
10
Insulation
Fork Terminal
BNJ46F
3.1g
0.8
11
BNJ46BPN10
10
1.4
.2
ø4
5.5
BNJ46B
10
10
2.8
BNJ46PN10
3.1g
Insulation
Ring Terminal BNJ46
BN15MW BNH15MW BN15MWT BNH15MWT BND15W BNDH15W BND15WT BNDH15WT
2
BNJ26FWBPN10
4.5
BNJ26FWB
11
4.5
BNJ26FW
40 (6-pole)
8
6.4 ø3. 7
11
BNJ26WB
BNJ26WPN10
4.5
BNJ26W
6
10 Insulation
Fork Terminal
BNJ56FPN10
Without
BNJ56FB
BNJ56FBPN10
With
4.2
12
30A
60 (6-pole)
10
1.4 0.8
.1
R2
4.5g 10
6
9.5 5.8
BNJ56F
9.3
BN30W BNH30W
1.7
12 mm
Package Quantity
2.8g
3.7
BNJ16F
Weight (Approx.)
1.4 0.8
2
BNJ16BPN10
35 (6-pole)
7
5.7 ø3.7
11
BNJ16B
BNJ16PN10
4
BNJ16
Current Applicable (Note 1, 2) Terminal Block
Dimensions
Insulation
•• Insulation color: Black, Insulation material: PVC Note 1: Ensure that the total current to the jumper does not exceed the maximum current. Note 2: Ensure that the current does not exceed the rated current of the terminal block to be used. Jumper for 2 poles Terminal Centers
Insulation
Dimensions Ring Terminal
BNJ62
BNJ62PN10
Without 14.5 mm
BNJ62B
BNJ62BPN10
Current (Note 1, 2)
Applicable Terminal Block
Package Quantity
le s)
Ordering No.
(h o
Part No.
80A With
BN40W (Note 3) BNH40W (Note 3) BN50W BNH50W
10
•• Material: nickel-coated brass •• Sheath: PVC Note 1: Ensure that the total current to the jumper does not exceed the maximum current. Note 2: Ensure that the current does not exceed the rated current of the terminal block to be used. Note 3: BN40W and BNH40: Do not install adjacently.
23
BN-W / BNH-W Series Terminal Blocks Accessories (Removal Tool) A tool for removing terminal blocks from the DIN rail. 23
20
Part No. BND2
15
13 6
8 24
92
Weight (Approx.) 8.6g
Package Quantity 1
•• Material: Steel •• Plating: Zinc Applicable terminal blocks: BN10W, BNH10W, BN15MW, BNH15MW, BN15MWT, BNH15MWT, BN15LW, BNH15LW, BN15LWT, BNH15LWT, BN30W, BNH30W (page 8 and 9)
Accessories for BND Double-Deck Terminal Blocks Surface Mounting Clip Part No.
Ordering No.
30
BNDL2 26
BNDL2PN10
Applicable Terminal Block BND15W, BNDH15W BND15WT, BNDH15WT BND15LW, BNDH15LW
Weight (Approx.)
Package Quantity
14.3g
10
•• Material: Steel •• Plating: Zinc
38 13
Connecting Rods Part No.
Ordering No.
BNR1
BNR1PN10
BNR2
BNR2PN10
Applicable Terminal Block
Weight (Approx.)
Dimensions (mm)
Package Quantity
BND15W, BNDH15W BND15WT, BNDH15WT BND15LW, BNDH15LW
21g
265 mm (M4×0.7)
10
43g
500 mm (M4×0.7)
10
•• Material: Steel •• Plating: Zinc
Connecting Nuts Part No.
Ordering No.
M4×0.7 Round Nut
BNN1 M4×0.7 Hex Nut
ø7 6
24
BNN1PN1H
•• Material: Steel •• Plating: Zinc
Applicable Terminal Block BND15W, BNDH15W BND15WT, BNDH15WT BND15LW, BNDH15LW
Weight (Approx.)
Package Quantity
14g
100 (pairs of both nuts)
BN-W / BNH-W Series Terminal Blocks Calculating Rail Lengths and Mounting Centers •• BNCA, BNCP, BAA, BAP, and BNJA Rails L1 = 12.5 × N L2 = L1 – 25
N: Rounded up numerical number from the calculated value of M. (Example: N for 19.1 is 20)
Note: This formula is for calculating the maximum rail length including tolerance. Depending on the combination of termi nal blocks, the required rail length may be shorter than the calculated value, particularly when many terminal blocks are combined.
BN150W BN100W BN75W
BNE150W BNT20 BNF10S
BN50W (BNH50W)
M=
(A + 0.1) n + B + C 12.5
A: Thickness of each terminal block B: Thickness of end plate C: Thickness of end clip when using 2 pieces of: BNL6 = 56.0 mm BNL7 = 62.5 mm BNL8 = 67.0 mm n: The number of terminal blocks
BNE20
BN40W (BNH40W)
BN400BW2 (BN400NW2)
BN30W (BNH30W) BN15LWT (BNH15LWT) BN15LW (BNH15LW)
BN300BW2 (BN300NW2) BN200BW2 (BN200NW2)
BN15MWT (BNH15MWT) BN15MW (BNH15MW) BN10W (BNH10W)
12.5 8.5
13
6.7
12 9.6
6
12 14 15.5
7 8
17
23
23
13 13
20
26
26
15 15
10.5
33
3
5
78 (2P) 115 (3P) 152 (4P)
40
52
92 (2P) 136 (3P) 180 (4P)
119 (2P) 176 (3P) 233 (4P)
L2 (Mounting Centers) L1 (Rail Length)
Rail Length (Double-Deck)
Mounting Centers (Double-Deck) Mounting Centers
L1 (Rail Length) L2 (Mounting Centers)
Spring Washer M4
7
35 End Plate BNDE15W Terminal Block
Rail Connecting BAA/BAP Rod End Clip BNR BNL6
Connecting Nut BNN1 7.6
Connecting Rod BNR
13.6 End Plate BNDE15W
Terminal Block
Surface Mounting Clip BNDL2 Connecting Nut BNN1
Calculating the length (mm)
Calculating the length (mm) Part No.
38
4.5
28
5
L3 (Terminal Block Length) 9
BND15W BNDH15W BND15WT
BND15LW BNDH15LW
L1 (∗1)
12.5 × N
L2 (∗2)
L1 – 25
L3 (∗1, ∗2)
8×n+9
10.5 × n + 10.3
Connecting Rod Length (∗1, ∗2)
8 × n + 8.7
10.5 × n + 10
BND15W BNDH15W BND15WT
Part No.
BND15LW BND15HLW
8 × n + 24.2
10.5 × n + 25.5
Connecting Rod Length (∗1, ∗2) 8 × n + 20.2
10.5 × n + 21.5
Mounting Centers (∗1, ∗2)
n: The number of terminal blocks
N: Rounded up numerical number from the calculated value of M. (Example: N for 19.1 is 20) For BND15W, BNDH15W, BND15WT
For BND15LW, BNDH15LW
10.5 × n + 10.3 + 62.5 (8 × n + 9 + 62.5) M= M= 12.5 12.5 ∗1: This formula is for calculating the maximum rail length including tolerance. Depending on the combination of terminal blocks, the required rail length may be shorter than the calculated value, particluarly when many terminal blocks are combined. ∗2: The length will be 1.5 mm longer when end plates BNDE15W2 and BNDE15LW2 are used.
25
BN-W / BNH-W Series Terminal Blocks Instructions How to Use Touch-Down Terminals
1. With the terminal screws in the up position, insert a ring crimping terminal.
2. Push down the head of the screw lightly to hold the crimping terminal.
Installation and Removal on Rails
3. When the wiring is in posi tion, tighten all the screws simultaneously.
4. To remove the wiring, loosen the screw and lightly push up.
Installation of Double-Deck Terminal Blocks (BND) Rail Mount (photo: when using BND15W, BNDH15W, BNDE15W2) End Plate BNDE15W
Terminal Block
Connecting Nut BNN1
Additional Installation and Removal (on DIN Rail) Installation
➡
Push
Removal Pull Out
➡
• The following terminal blocks can be added or removed: BN10W, BNH10W, BN15MW, BNH15MW, BN15LW, BNH15LW, BN30W, BNH30W, BN15MWT, BNH15MWT, BN15LWT, BNH15LWT • Can be installed/removed for two to three times maximum.
Securing the Ends of the Marking Strip The ends of the marking strip can be secured with a mark ing strip fastener (or end plate).
Rail BAA/BAP
BND15W/BNDH15W
1. Install end plate. Then mount the terminal blocks onto the DIN rail. 2. Insert connecting rod (BNR) through each hole of the ter minal blocks. 3. Secure the ends of the connecting rods with connecting nuts (BNN1). 4. To prevent side-to-side movement on the DIN rail, use the BNL6 end clips at both ends of the rail. Surface Mount End Plate BNDE15W Connecting Nut BNN1 Surface Mounting Clip BNDL2
BND15W/BNDH15W
To Secure the Marking Strip
Installing End Plate
For double-deck, use an end plate to secure marking strips (BNDE15W2, BNDE15LW2).
26
Connecting Rod BNR Connecting Nut BNN1 End Clip BNL6
Terminal Block Connecting Rod BNR Connecting Nut BNN1 Surface Mounting Clip BNDL2
1. Assemble a row of terminal blocks with end plates on exposed ends. 2. Use BNDL2 mounting clips at both ends of a row. 3. With the two holes of the mounting clip (BNDL2) aligned with the terminal block holes, insert a connecting rod (BNR) through each hole. 4. Secure the ends of the connecting rods with the connect ing nuts (BNN1).
BN-W / BNH-W Series Terminal Blocks Instructions Dust Covers on the Lower Deck Terminal of Double-Deck Terminal Blocks Installing Dust Covers on Lower Deck Terminals Push in
Lower Deck Dust Cover
Groove
Groove
1. Press the lower end of the dust cover into the groove.
2. With the lower end of the dust cover pressed into the groove, push in the top end in the direction of the arrow.
Removing Dust Covers from Lower Deck Terminals Turn the power off before removing the dust cover. 1. Hold the end of the dust cover which is extruding from the end plate.
2. Lift up in the direction of the arrow. 3. If the dust cover cannot be removed all at once, place fingers between the terminal block and dust cover, and slowly remove the dust cover.
Length of Double-Deck Dust Covers Cut required length depending on the number of terminal blocks used. (Length in mm) Terminal Dust 1-pole 2-pole 3-pole 4-pole 5-pole 6-pole 7-pole 8-pole n-pole Block Cover Upper 12 20 28 36 44 52 60 68 8 (n+1) – 4 BND(H)15W Deck BND(H)15WT Lower 16 24 32 32 48 56 64 72 8 (n+1) Deck Upper 16 26.5 37 47.5 58 68.5 79 89.5 10.5 (n+1) – 5 Deck BND(H)15LW Lower 21 31.5 42 52.5 63 73.5 84 94.5 10.5 (n+1) Deck
Upper-Deck Dust Cover BNC230
Lower-Deck Dust Cover BNC240
Securing Marking Strip with Marking Strip Fasteners for Double-Deck Terminal Blocks Because marking strips can be secured without using marking strip fasteners, installation time can be shortened. Also, marking strips can be inserted and removed after instal lation.
End Plate for Fastening Marking Strips BNDE15W2 BNDE15LW2
End Plate BNDE15W BNDE15LW
Marking Strip BNM7 BNM9 BNM725
Terminal Block BND(H)15W BND(H)15WT BND(H)15LW
End Plate for Fastening Marking Strips BNDE15W2 BNDE15LW2
Marking Strip BNM7 BNM9 BNM725
Terminal Block BND(H)15W BND(H)15WT BND(H)15LW
End Plate BNDE15W BNDE15LW
Notes on Wiring
Washer Width
Terminal Clip
Crimping Terminals •• When using crimping terminals, be sure to use insulated terminals to prevent electric shocks.
Without Crimping Terminals •• Insert the wire until the insulation comes into contact with the terminal metal part. •• Strip the insulation so that the wire is longer than the width of the wire clamp. •• When connecting two wires, use wires of the same size.
Wire
27
BA Series Terminal Blocks Quick-mount terminal blocks for mounting on 35-mm-wide DIN rails. Current capacities from 16A to 400V (600V). • Snaps on to 35-mm-wide DIN rails. • Wide range of current capacities from 16A to 400A. Insulation voltage is 600V. • No end plates are required. • 3-pole units, fuse blocks with blown fuse indicators available. • Large capacity types (BA811S, BA911S) can be mounted directly to panels. • Material: PPE (black) • Complies with JIS C 2811. • UL recognized and CSA certified. (BA111T, BA211T, BA311T, BA411S, BAF111SU, BAF111SNU) Applicable Standards
Certification Organization/ File No. UL recognized File No. E78117
Mark
UL1059
CSA (File No. LR64803)
CSA 22.2 No. 158 Quick-mount
Unlatch
Snap on
General Ratings
No end plates required
Dielectric Strength Insulation Resistance Operating Temperature Storage Temperature Operating Humidity
Remove
Push
Pull
2500V AC, 1 minute 100MΩ minimum –25 to +55°C (no freezing) –25 to 70°C (no freezing) 45 to 85% RH (no condensation)
Terminal Blocks Style
Part No. BA111T
3-pole Self-Lifting
Self-Lifting
Large Capacity 1-pole
Fuse Fuse with Lamp Without Fuse WIthout Fuse/ With Lamp With Disconnecting Switch
UL/CSA Voltage/ Wire Size Current (AWG)
Ordering No. BA111TPN20
Voltage/ Current
300V/15A 22-14
600V/16A
BA211T
BA211TPN20
300V/20A 22-12
600V/21A
BA311T BA411S BA611S BA711S BA811S
BA311TPN20 BA411SPN50 BA611SPN10 BA711SPN06 BA811SPN06
150V/30A 18-10 600V/40A 16-6 — — — — — —
600V/40A 600V/70A 600V/94A 600V/132A 600V/240A
BA911S
BA911SPN06
JIS Wire Size (mm2) 1.25 mm2 (2 mm2) 2 mm2 (3.5 mm2) 5.5 mm2 14 mm2 22 mm2 38 mm2 100 mm2 200 mm2
Tightening Terminal Package Torque Screw Quantity (N·m) M3
0.6 to 1.0
20
M3.5
1.0 to 1.3
20
M4 M5 M6 M8 M10
1.4 to 2.0 2.6 to 3.7 3.9 to 5.4 10 to 13.5 21 to 28
20 50 10 6 6
(200 mm2 2 wires) M12 (325 mm2 1 wire)
38 to 49
6
—
600V/370A
— — BAF111S- BAF111S-PN20 — — BAF111SN- BAF111SN-PN20 BAF111SU BAF111SUPN20 600V/10A 18-10
600V/10A 600V/10A 600V/10A
5.5 mm2 5.5 mm2 5.5 mm2
M4 M4 M4
1.4 to 2.0 1.4 to 2.0 1.4 to 2.0
20 20 20
BAF111SNU
BAF111SNUPN20
600V/10A
5.5 mm2
M4
1.4 to 2.0
20
BAT20
BAT20PN20
600V/20A
5.5 mm2
M4
1.4 to 2.0
20
—
600V/10A 18-10 —
—
1. Specify fuse ratings 1A, 3A, or 5A in place of in the Part No. 2. The wire size in ( ) does not comply with JIS standards. 3. The voltage/current differ according to operating conditions. See “Selecting Terminal Blocks by Current According to JIS Standards” on page 4. 4. Use a socket wrench orscrewdriver for tightening screws.
: Order when a marking strip or a dust cover is needed. ▲: Used for surface mounting ∗ : Dust cover with fuse holder Part No.
BA111T, BA411S, BAT20, BA211T, BA611S, BA711S, BA311T BA811S, BA911S BAF111S, BAF111SN, BAF111SU, BAF111SNU
28
Material
Accessories (× Necessary) DIN End Marking Dust Cover Rail Clip Strip
Surface Connecting Connecting Mounting Rod Nut Clip
×
×
—
—
—
×
×
×
×
▲
×
×
∗
—
—
—
Parts Name Housing Bus Bar Terminal Screw
Material Polyamide Brass (nickelplated) Steel (zinc chromeplated)
BA Series Terminal Blocks M3
4
16.5
1.8 When using BAA:32
M3 Terminal Screws
ø3.2 min. 6.6 max. 5 max.
3.3 min.
25
41.5
Weight: Approx. 18.8g M3.5
21A
Terminal Cover
9.8 8.5
When using BAA:32
1.8
36
Standards Insulation Voltage Rated Current ∗2 Dielectric Strength Insulation Resistance
9.8 M3.5 Terminal Screws
4
16.5 28.5
ø3.6 min. 8.4 max. 5 max.
30.5
41.5
Weight: Approx. 25.3g M4
40A
11 9.6
When using BAA:33.5 1.8
Terminal Cover
38
M4 Terminal Screws ø4.2 min.
4
16.9
30
9.4 max. 6 max.
4.5 min.
34.5
42
Weight: Approx. 40.0g M5
M5 Terminal Screws
When using BAA:37.5
13
ø5.2 min.
12.8 max.
34 4 45
6.5 max.
4.5 min.
16
22
Rated Current ∗2 Dielectric Strength Insulation Resistance Wire Size ∗1
2
63
ø6.2 min. 16.8 max. 8.5 max.
6 min.
Weight: Approx. 53.0g
Wire Size ∗1
0.5
Marking Strip Width Dust Cover Rail See page
Rated Current ∗2 Dielectric Strength Insulation Resistance Wire Size Marking Strip Width Dust Cover Rail See page
Insulation Voltage
65 Dust Cover
ø8.5 min. 22.8 max. 11 max.
8 min.
Weight: Approx. 103.3g Socket wrench: 12.7 mm square drive hexagonal socket 13 ∗3
Rated Current ∗2 Dielectric Strength Insulation Resistance Wire Size Marking Strip Width Dust Cover Rail See page
Accessories
23
When using BAA/BAP: 51.5
32
2
2-M8 Hexaganol Bolt 26.5
M8
Dust Cover Rail See page
Rated Current ∗2 Dielectric Strength Insulation Resistance
Socket wrench: 12.7 mm square drive hexagonal socket 10 ∗3
BA711S 132A
Marking Strip Width
Insulation Voltage
65 Dust Cover
17
When using BAA/BAP: 43.5
M6
23.4
94A
2-M6 Hexagonal Bolt
Weight: Approx. 23.4g
BA611S
Dust Cover Rail See page
Standards Insulation Voltage
Terminal Cover
47.5
19.3
70A
1.2
BA411S
Marking Strip Width
Standards Insulation Voltage
11
Accessories
BA311T (3 Pole)
Wire Size ∗1
4 min.
Accessories
BA211T (3 Pole)
Accessories
7.9 7.9 6.7
UL/CSA JIS 300V 600V 15A max. 16A 2,500V AC, 1 minute 100 MΩ minimum 22-14 1.25 mm2 Wire Size ∗1 AWG (2 mm2) mm (BNM7, BNM9, Marking Strip Width 9.5 BNM725) Dust Cover BNC220 Rail BAP1000, BAA1000 See page 31
Accessories
Terminal Cover 36
Standards Insulation Voltage Rated Current ∗2 Dielectric Strength Insulation Resistance
Accessories
16A
28.5
BA111T (3 Pole)
UL/CSA JIS 300V 600V 20A max. 21A 2,500V AC, 1 minute 100 MΩ minimum 22-12 2 mm2 (3.5 mm2) AWG 9.5 mm (BNM7, BNM9, BNM725) BNC220 BAP1000, BAA1000 31 UL/CSA JIS 150V 600V 30A max. 40A 2,500V AC, 1 minute 100 MΩ minimum 18-10 5.5 mm2 AWG 9.5 mm (BNM7, BNM9, BNM725) BNC230 BAP1000, BAA1000 31 UL/CSA JIS 600V 600V 40A max. 70A 2,500V AC, 1 minute 100 MΩ minimum 16-6 AWG 14 mm2 9.5 mm (BNM7, BNM9, BNM725) BNC320 BAP1000, BAA1000 31 600V 94A max. 2,500V AC, 1 minute 100 MΩ minimum 22 mm2 9.5 mm (BNM7, BNM9, BNM725) BNC520 BAP1000, BAA1000 31
600V 132A max. 2,500V AC, 1 minute 100 MΩ minimum 38 mm2 9.5 mm (BNM7, BNM9, BNM725) BNC520 BAP1000, BAA1000 31
∗1: The wire size in ( ) does not comply with JIS standards. ∗2: The voltage/current differ according to operating conditions. See “Selecting Terminal Blocks by Current According to JIS Standards” on page 4. ∗3: Screws can be tightened with a socket wrench. *4: The grooves on the head of the hex bolt are for temporary tightening. For proper tightening, use an applicable socket wrench and tighten within the range of the recommended tightening torque.
29
BA Series Terminal Blocks BA911S 370A
M10
Weight: Approx. 185.0g
Weight: Approx. 406.3g
Surface Mounting Clip (BAL3)
End Clip (BAL2)
140
51
77
Dust Cover
Surface Mounting Clip (BAL3)
94 (2P) 136 (3P) ∗ 94 (4P)
Surface Mounting Clip (BAL3)
Connecting Rod/Nut
ø4.5 Hole (or M4 Screw)
ø10.5 min. 32.8 max. 16 max.
84
11 min.
∗130 (4P)
50.8 max.
26 max.
120
BA811S BA911S 600V 240A 370 (400A) 2,500V AC, 1 minute 100MΩ minimum 200 mm2 ∗1 (200 mm2 100 mm2 2 wires) (325 mm2 1 wire) M10 M12 BNR1, BNR2, BNL8 BAN1 BAL2, BAL3 9.5 mm (BNM7, BNM9, BNM725) BAC820 BNC92 BAP1000, BAA1000 31
14 min.
∗Use 3 surface mounting clips (BAL3) for 4-pole mounting
• BAF111SN is equipped with a neon lamp (for 100 or 200V AC) which turns on when the fuse is blown.
M4 63 36
• Internal Connection
ø4.2 min.
When using BAA/BAP: 49
16 10
22.5
2-M4 Screw
10A
ø12.5 min.
130 (2P) 190 (3P)
∗Use 3 surface mounting clips (BAL3) for 4-pole mounting
BAF111S (Fuse)
Connecting Rod/Nut
ø4.5 Hole (or M4 Screw)
Terminal Screw Connecting Rod Connecting Nut End Clip/ Surface Mounting Clip Marking Strip Width Dust Cover Rail See page
Accessories
60
1.5
2-M12 Hexagonal Bolt
1.5
85 Dust Cover
Wire Size
Connecting Rod/Nut
Surface Mounting
42
Rated Current ∗2 Dielectric Strength Insulation Resistance
1.5
Dust Cover
60
2-M10 Hexagonal Bolt
Surface Mounting 33
140
51
Surface Mouting Clip (BAL3)
Connecting Rod/Nut
End Clip (BAL2)
60
When using BAA/BAP: 78.5
When using BAA/BAP: 61.5
Dust Cover
Part No. Insulation Voltage
37.5
1.5
85
2-M12 Hexagonal Bolt
Socket wrench: 12.7 mm square drive hexagonal socket 19
42
33
M12
Socket wrench: 12.7 mm square drive hexagonal socket 17
30.5
2-M10 Hexagonal Bolt
BA811S 240A
10 max.
5.2 max.
Fuse
4.5 min. Neon Lamp
Accessories
M4
Dust Cover
63
ø4.2 min.
10 max. 6.4 max.
4.5 min.
Accessories
Insulation Voltage Rated Current Dielectric Strength Insulation Resistance Wire Size Terminal Screw
65 2
16 10
20A
22.5
2-M4 Screw
BAT20 (With Disconnecting Switch)
BAF111S (with fuse)/BAF111SN (without fuse/with lamp) Insulation Voltage 600V • Fuse ratings • Use UL/CSA Rated voltage: 250V approved fuses 10A max. Rated Current Rated current: 1, 3, 5A (10A maximum) (depends on fuse rating) Cartridge fuse: JIS C6575-2 • Fuse size Dielectric Strength 2,500V AC, 1 minute 6.35×31.8 mm Insulation Resistance 6.35×31.8 mm 100 MΩ minimum 6.40×30 mm Wire Size 18-10 AWG Part No. Terminal Screw M4 BAF111S-1A mm (BNM7, BNM9, BAF111S-3A Marking Strip Width 9.5 BNM725) BAF111S-5A BAF111SN-1A Dust Cover — BAF111SN-3A Rail BAP1000, BAA1000 BAF111SN-5A See page 31
When using BAA/BAP: 39.5
Accessories
BAF111S (with fuse)/BAF111SN (with fuse/lamp) Insulation Voltage 600V 10A max. Rated Current (depends on fuse rating) Dielectric Strength 2,500V AC, 1 minute Insulation Resistance 100MΩ minimum Wire Size 5.5 mm2 Terminal Screw M4 9.5mm (BNM7, BNM9, Marking Strip Width BNM725) Dust Cover — Rail BAP1000, BAA1000 See page 31
600V 20A 2,500V AC, 1 minute 100 MΩ minimum 5.5 mm2 max. M4
Marking Strip Width
9.5 mm (BNM7, BNM9)
Dust Cover
BNC520
Rail
BAP1000, BAA1000
See page
31
BAT20 is not capable of breaking circuits. Do not apply voltage when opening or closing the circuit. Turn the slot using a screwdriver. ∗1: The wire size in ( ) does not comply with JIS standards. ∗2: The rated current differs according to operating conditions. See “Selecting Terminal Blocks by Current According to JIS Standards” on page 4. ∗3: The grooves on the head of the hex bolt are for temporary tightening. For proper tightening, use an applicable socket wrench and tighten within the range of the recommended tightening torque.
30
BA Series Terminal Blocks Accessories Rails
5.5
BAA
BAP
BAA:1.7 BAP:1
7.5
35 25
12.5
12.5
DIN Rail 35-mm-wide
BAA:31 BAP:27
BAA BAP
Length
Part No. BAA1000 (Note) BAP1000
1000 mm
Ordering No. BAA1000PN10 BAP1000PN10
Material Aluminum Steel
Weight (Approx.) 200g 320g
Package Quantity 10 10
Note: 2000 mm is also available. Contact IDEC.
Marking Strip (BNM) Part No.
Ordering No.
Package Quantity
Dimensions
BNM7
BNM7PN10
10
9.5 × 0.5t × 1m
BNM9
BNM9PN10
10
9.5 × 0.5t × 1m
BNM725
BNM725
1
9.5 × 0.5t × 25m
BNM3
BNM3PN50
50
End Clip Used on the ends of a group of terminal blocks to secure and prevent sliding along the rails.
24 45
9
32.5 46
BNL6 (M4 Screw) (Tightening torque: 1.1 N·m)
BNL8 (M4 Screw)
14.4
Part No. BNL6 BNL8 BAL2 26 (35)
45
12
BAL2 (Weight: Approx. 25.2g)
Material PVC (glossy surface) Fiber Glass (matte surface) PVC (glossy surface)
Ordering No. BNL6PN10 BNL8PN10 BAL2PN10
Package Quantity 10 10 10
Notes on Selecting End Clips • When using BA611S, use BAL2 or BNL8. Also, when using BA711S, BA811S, BA911S of 100A or larger, use BAL2 or BNL8. • When mounting rails vertically, use BAL2 or BNL8.
Material: Steel (zinc chrome-plated)
Dust Cover
Material: Polycarbonate Item
Dust Cover (1m)
Dust Cover (500 mm)
Part No. BNC220 BNC230 BNC320 BNC520 BAC820 BNC92
Ordering No. BNC220PN10 BNC230PN10 BNC320PN10 BNC520PN10 BAC820PN10 BNC92PN10
Size (mm) A B 37.6 8.5 39.6 8.5 49.6 8.5 65.0 9.0 85.0 10.6 140.5 9.8
Terminal Block BA111T, BA211T BA311T BA411S BA611S, BA711S, BAT20 BA811S BA911S
Package Quantity 10 10 10 10 10 10
31
BA Series Terminal Blocks Connecting Rod/Connecting Nut (For BA811S, BA911S)
BNR1: M4 × 0.7 L = 265 (21.0g) BNR2: M4 × 0.7 L = 500 (43.0g) Item Connecting Rod (265 mm) Connecting Rod (500 mm) Connecting Nut (4 pcs/set)
Part No. BNR1 BNR2 BAN1
BAN1: M4 × 0.7 (2.5g)
Ordering No. BNR1PN10 BNR2PN10 BAN1PN10
Weight (Approx.) 2.6g 43g 2.5g
Package Quantity 10 10 10
Remarks M4 × 0.7 M4 × 0.7 M4 × 0.7
Surface Mounting Clip (For BA811S and BA911S Only) Used on the ends of groups of terminal blocks for direct mounting to panels.
Part No. BAL3
Weight (approx.) 12.4g
Ordering No. BAL3PN10
Package Quantity 10
Material: Steel (zinc-chrome plated) BAL3
Calculating Rail / Connecting Rod Length BA611S BA411S
BA911S
BA811S
BA711S BA111SN BAF111S
BA311T BA211T
BAT20
BA111T
25
30.5
34.5
16
22
32
16
16
L2 (Mounting Centers) L1 (Rail Length)
42
60 L2 L1
Calculating Rail Length
Calculating Connecting Rod Length
For BAA, BAP rails L1 = 12.5 × N L2 = L1 – 25 A: Total thickness of each terminal block B: Tolerance of stacking thickness 0.1 mm per block C: End Clip When using 2 pieces of BNL6 or BAL2 = 62.5 N: Rounded up numerical number from the calculated value of M. (Example: N for 19.1 is 20) A+B+C M= 12.5
L = 42 × n1 + 60 × n2 + 10.2 n1: BA811S n2: BA911S n: The number of terminal blocks
Note: This formula is for calculating the maximum rail length including tolerance. The rail length may be shorter than the calculated value, depending on how the terminal blocks are combined.
32
BA Series Terminal Blocks Instructions Installation of BA811S and BA911S Connecting Rod BNR
Connecting Nut BAN1
End Clip BAL2 Surface Mounting Clip BAL3
Rail Mount 1. Mount the terminal block on DIN rail. 2. Mount the surface mounting clips (BAL3) on both ends and slide 2 connecting rods (BNR) through the holes in the terminal blocks. 3. Tighten both ends of the connecting rod with a connecting nut (BAN1). 4. Secure the terminal blocks with end clips (BAL2).
Notes on Wiring Crimping Terminals • When using crimping terminals, be sure to use insulated terminals to prevent electric shocks. Without Crimping Terminals • Insert the wire until the insulation comes into contact with the terminal metal part. • Strip the insulation so that the wire is longer than the width of the wire clamp. • When connecting two wires, use wires of the same size. Washer Width
Terminal Metal Part
Wire Insulation
Surface Mount 1. Mount the terminal block to the panel. 2. Mount the surface mounting clips (BAL3) on both ends and slide 2 connecting rods (BNR) through the holes in the terminal blocks. 3. Tighten both ends of the connecting rod with connecting nuts (BAN1). 4. Secure the terminal blocks to the panel.
33
BN1U Spring-Up Screw Terminal Blocks Spring-up screws save up to 30% wiring time (compared to IDEC standard terminal blocks) • Spring-up screws with temporary hold function. • M3, M3.5, and M4 types are all in the same height and width. • The same dust covers, marking strips (9.5-mm-wide), and end plates can be used. • Can be mounted on a 35-mm-wide DIN rial or 30-mm-wide C type rail. • Each block can be easily removed from a 35-mm-wide DIN rail using a flat screwdriver. • UL recognized for field wiring (FW2). • UL recognized, CSA certified, and EN compliant (TÜV approved). Applicable Standards
Mark
UL1059
Certification Organization / File No. UL recognized File No.E78117
CSA C22.2 No.158
CSA LR64803
EN60947-7-1
TÜV Rheinland License No.R9551701
BN1U Spring-Up Screw Terminal Blocks 1 The terminal screw is always
screw to the bus bar, tilt the terminal screw in the the direction as shown.
4 When loosening, the screw
screw.
straight down to the bus bar using a screwdriver.
2 After pressing the terminal
Temporary Hold
3 Tighten the terminal
2 Push the terminal screw
Immediate Tightening
in the lifted position, ready for wiring. A ring terminal can be inserted easily.
3 When tightening the
screw, make sure that it is in the upright position.
springs straight up.
4 Tighten the terminal
screw.
If the screw stops at the temporary position, the screw will return to the original position by pushing further down.
Ratings·Terminal Screw Tightening Torque Part No.
BN1U-16W
JIS Rated Insulation Applicable Voltage Wire (mm2) Current 1.25 (2) 16A (Note)
UL Rated Insulation Applicable Voltage Wire (mm2) Current
CSA Rated Insulation Applicable Voltage Wire (mm2) Current
EN Rated Insulation Applicable Wire Voltage (mm2) Current
15A
15A
22A
22-14AWG
22-14AWG
2 (22-14AWG)
Terminal Screw
Terminal Screw Recommended Tightening Torque
M3
0.6 to 1.0N·m
BN1U-20W
21A
2
15A
22-14AWG
15A
22-14AWG
22A
2 (22-14AWG)
M3.5
1.0 to 1.3N·m
BN1U-40W
40A
5.5
35A
18-10AWG
35A
18-10AWG
38A
5.5 (18-10AWG)
M4
1.4 to 2.0N·m
Note: Rated applicable wire is 1.25mm2, and 2mm2 wire can be connected.
Terminal Blocks Type
Ordering No.
Rated Applicable Wire (mm2)
Terminal Screw
Terminal Width (mm) 7
16A
BN1U-16W
BN1U-16WPN50
1.25 (2)
M3
21A
BN1U-20W
BN1U-20WPN50
2
M3.5
8
40A
BN1U-40W
BN1U-40WPN50
5.5
M4
11
(Based on JIS C2811)
34
Part No.
Package Quantity
Page
50
35
BN1U Spring-Up Screw Terminal Blocks Terminal Blocks
BN1U-16WPN50 50 7g
Ordering No. Package Quantity Weight (Approx.)
38 18
3
6.7
11.8 8
BN1U-40W
3
BN1U-20WPN50 50 8g
M4
40A
38 19.4
9.6
15.1 11
31.9 24.7
10.8 7
31 23.8
When using DIN Rail: 36.5 When using C Rail: 43.7 34
5.9
M3.5
21A
When using DIN Rail: 36.5 When using C Rail: 43.7 34
38 18
3
BN1U-20W
When using DIN Rail: 36.5 When using C Rail: 43.7 34
Dimensions
M3
16A
31 23.8
BN1U-16W
Part No.
BN1U-40WPN50 50 14g
Specifications and Ratings UL
CSA EN JIS UL CSA EN JIS UL CSA EN JIS CSA C22.2 EN CSA C22.2 EN CSA C22.2 EN JIS C 2811 UL1059 JIS C 2811 UL1059 JIS C 2811 UL1059 No.158 60947-7-1 No.158 60947-7-1 No.158 60947-7-1 600V 660V 600V 600V 660V 600V 600V 660V 600V 5.5 mm2 2 mm2 1.25 mm2 2 mm2 2 2 mm 18-10 AWG 5.5 mm2 22-14 AWG 22-14 AWG 2 22-14 AWG (2 mm ) 22-14 AWG 18-10 AWG 15A 22A 16A 15A 22A 21A 35A 38A 40A M3 M3.5 M4
Standards Insulation Voltage Wire Size Rated Current Terminal Screw Max. No. of Crimp Terminals Tightening Torque Terminal Centers
2
2
2
0.6 to 1.0 N·m 7 mm
1.0 to 1.3 N·m 8 mm
1.4 to 2.0 N·m 11 mm
ø3.2 min. Crimp Terminal Dimensions (mm)
5.8 max. 5 max.
Accessories
Operating Temperature Storage Temperature Operating Humidity Mounting Method Insulation Resistance Dielectric Strength Vibration Resistance Shock Resistance End Plate Dust Cover Marking Strip Marking Strip Fastener DIN Rail / End Clip C Rail / End Clip 35 mm DIN + C Rail / End Clip Jumpers
ø3.6 min. 6.6 max. 5 max.
3.3 min.
3.9 min.
ø4.2 min. 9.5 max. 5.5 max.
4.5 min.
–25 to +55°C (no freezing) –25 to +70°C (no freezing) 45 to 85% RH (no condensation) Rail mounting 100 MΩ minimum (500V DC megger) 2500V AC, 1 minute Frequency: 5 to 55 Hz, Amplitude: 0.5 mm 1000 m/s2 (100G) BN9Z-E16W BTB-CV30L2 (1000 mm), BTB-CV30L1 (500 mm) BNM7: PVC 1m, BNM9: Fiber glass: 1m, BNM725: PVC 25m BNM3 BAA1000: Aluminium, BAP1000: Steel / BNL6 BNCA1000: Aluminium, BNCP1000: Steel / BNL7 BNJA1000: Aluminium / BNL6 (35-mm-DIN rail side), BNL7 (C rail side) BNJ16, BNJ16B BNJ16F, BNJ16FB
Material
BNJ26W, BNJ26WB BNJ26FW, BNJ26FWB
BPJ-56, BPJ-56B BPJ-56F, BPJ-56FB 38
End Plate
Housing
Modified PPE (UL94V-0)
Part No.
BN9Z-E16W
End Plate
Modified PPE (UL94V-0)
Ordering No.
BN9Z-E16WPN10
Bus Bar
Brass (nickel-plated)
Applicable Terminal Block
BN1U-16W, BN1U-20W, BN1U-40W
Terminal Screw
Steel (zinc trivalent chrome-plated)
Package Quantity
10
Spring
Stainless steel
Weight (Approx.)
3g
5
35
BN1U Spring-Up Screw Terminal Blocks Accessories Rail Length
Item
Part No.
35-mm-wide DIN Rail 1000 mm
30-mm-wide C Rail 35-mm-wide DIN+C Rail
Ordering No.
Material
Weight (Approx.)
Package Quantity 10
BAA1000
BAA1000PN10
Aluminum (anodized)
200g
BAP1000
BAP1000PN10
Steel (trivalent chrome-plated)
320g
10
BNCA1000
BNCA1000PN10
Aluminum (anodized)
260g
10
BNCP1000
BNCP1000PN10
Steel (trivalent chrome-plated)
700g
10
BNJA1000
BNJA1000PN10
Aluminum (anodized)
340g
10
End Clip Part No.
Ordering No.
Material (Surface Treatment)
Weight (Approx.)
Applicable Rail
Package Quantity
BNL6
BNL6PN10
Steel (trivalent chrome-plated)
15.2g
35-mm-wide DIN Rail (BAA, BAP, BNJA)
10
BNL7
BNL7PN10
Steel (trivalent chrome-plated)
16g
30-mm-wide C Rail (BNCA, BNCP, BNJA)
10
Dust Cover Length
Part No.
Ordering No.
1000 mm
BTB-CV30L2
BTB-CV30L2PN10
500 mm
BTB-CV30L1
BTB-CV30L1
Material
Weight (Approx.)
Polycarbonate (UL94V-0)
Applicable Terminal Blocks
Package Quantity
53g
BN1U-16W, BN1U-20W, BN1U-40W
10
27g
BN1U-16W, BN1U-20W, BN1U-40W
1
• BNC230 dust cover (1000 mm) can also be mounted to the BN1U-16W and BN1U-20W terminal blocks.
Marking Strip, Marking Strip Fastener Item
Part No.
Ordering No.
Weight
Package Quantity
Description
BNM7
BNM7PN10
7.2g
10
9.5-mm-wide Marking Strip
PVC (glossy surface), length 1000 mm × width 9.5 mm × thickness 0.5 mm
BNM9
BNM9PN10
6.4g
10
Fiber glass (matte surface), length 1000 mm × width 9.5 mm × thickness 0.5 mm
BNM725
BNM725
Marking Strip Fastner
BNM3
BNM3PN50
0.1g
Insulation
Part No.
–
1 (25m)
PVC (matte surface), length 25m × width 9.5 mm × thickness 0.5 mm
10
Material: polycarbonate
Jumper Terminal Centers
Terminal Style Ring
7 mm (6 poles) Fork Ring 8 mm (6 poles) Fork Ring 11 mm (6 poles) Fork
Ordering No.
Without
BNJ16
BNJ16PN10
With
BNJ16B
BNJ16BPN10
Without
BNJ16F
BNJ16FPN10
With
BNJ16FB
BNJ16FBPN10
Without
BNJ26W
BNJ26WPN10
With
BNJ26WB
BNJ26WBPN10
Without
BNJ26FW
BNJ26FWPN10
With
BNJ26FWB
BNJ26FWBPN10
Without
BPJ-56
BPJ-56PN10
With
BPJ-56B
BPJ-56BPN10
Without
BPJ-56F
BPJ-56FPN10
With
BPJ-56FB
BPJ-56FBPN10
Maximum Rated Current *
Applicable Terminal
Package Quantity
10A
BN1U-16W
10
20A
BN1U-20W
10
20A
BN1U-40W
10
* The maximum rated current is the value of each pole.
Notes on Wiring • Tighten all terminal screws including unused terminal screws. • Be careful not to drop a terminal block (without an end plate) as the spring may fall out from the housing. • Tighten the terminal screw to the recommended tightening torque.
Bus Bar
Crimp Terminals • When using crimp terminals, be sure to use insulated terminals to prevent electrical shocks.
Without Crimp Terminals • Insert wire until the insulation comes into contact with the bus bar. • Strip the insulation so that the wire is longer than the washer width. (BN1U-16W: approx. 9 mm, BN1U-20W: approx. 9 mm, BN1U-40W: approx. 11 mm) • When connecting two wires, use wires of the same size.
36
Wire
BTB / BTBH Series Surface Mount Terminal Blocks Surface mount terminal blocks with 2 to 30 poles. Touch-down terminals reduce wiring time. • Self-lifting (BTB series) and touch down terminal (BTBH) available. • Flame-resistant plastic (UL94V-0). • Terminal blocks can be easily combined and all poles can be secured with a pair of connecting rods and nuts. • Complies with JIS C 2811. • UL recognized and CSA certified. Applicable Standards
Mark
UL1059
Certification Organization/ File No. UL recognized File No. E78117
CSA 22.2 No. 158
CSA (File No. LR64803)
EN60947-1 EN60947-7-1
TÜV Rheinland License No. R9551515
General Specifications Dielectric Strength Insulation Resistance Operating Temperature Storage Temperature Operating Humidity
Material
2500V AC, 1 minute 100 MΩ minimum –25 to +55°C (no freezing) –25 to +70°C (no freezing) 45 to 85% RH (no condensation)
Parts Name Housing Bus Bar Terminal Screw Connecting Rod/Nut Dust Cover
Material Modified PPE Brass (nickel-plated) Steel (zinc chrome-plated) Steel (zinc chrome-plated) Polycarbonate
Ratings and Terminal Screw Tightening Torque Part
Part No.
BTB15C BTB15LC BTB Self-lifting BTB30C BTB50C BTBH15C BTBH15LC TouchBTBH down BTBH30C BTBH50C
UL/CSA Voltage/ Wire Size Current (AWG) 300V/10A 22-14 300V/15A 22-12 300V/30A 18-10 600V/50A 16-6 300V/10A 22-14 300V/15A 22-14 300V/30A 18-10 600V/50A 16-6
EN Voltage/ Current 500V/22A 500V/22A 500V/38A 500V/67A 500V/22A 500V/22A 500V/38A 500V/67A
Wire Size (AWG) 2 (18-14) 2 (18-14) 5.5 (14-10) 14 (10 -6) 2 (18-14) 2 (18-14) 5.5 (14-10) 14 (10-6)
JIS Voltage/ Current 600V/16A 600V/21A 600V/40A 600V/70A 600V/16A 600V/21A 600V/40A 600V/70A
Wire Size (mm2) 1.25 (2) ∗ 2 5.5 14 1.25 (2) ∗ 2 5.5 14
Terminal Screw
Tightening Torque
M3 M3.5 M4 M5 M3 M3.5 M4 M5
0.6 to 1.0 1.0 to 1.3 1.4 to 2.0 2.6 to 3.7 0.6 to 1.0 1.0 to 1.3 1.4 to 2.0 2.6 to 3.7
∗ The rated applicable wire size is 1.25 mm2, but 2 mm2 wire can also be used. The wire size in ( ) does not comply with JIS standards. The rated current differs according to operating conditions. See “Selecting Terminal Blocks by Current According to JIS Standards” on page 4. Specify the number of poles in place of .
37
BTB / BTBH Series Surface Mount Terminal Blocks BTB15C/BTBH15C Style
BTB15C (Self-lifting terminal)
No. of Poles 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
Part No. BTB15C2 BTB15C3 BTB15C4 BTB15C5 BTB15C6 BTB15C7 BTB15C8 BTB15C9 BTB15C10 BTB15C11 BTB15C12 BTB15C13 BTB15C14 BTB15C15 BTB15C16 BTB15C17 BTB15C18 BTB15C19 BTB15C20 BTB15C21 BTB15C22 BTB15C23 BTB15C24 BTB15C25 BTB15C26 BTB15C27 BTB15C28 BTB15C29 BTB15C30
Package Quantity 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Style
BTBH15C (Touch-down terminal)
No. of Poles 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
Part No. BTBH15C2 BTBH15C3 BTBH15C4 BTBH15C5 BTBH15C6 BTBH15C7 BTBH15C8 BTBH15C9 BTBH15C10 BTBH15C11 BTBH15C12 BTBH15C13 BTBH15C14 BTBH15C15 BTBH15C16 BTBH15C17 BTBH15C18 BTBH15C19 BTBH15C20 BTBH15C21 BTBH15C22 BTBH15C23 BTBH15C24 BTBH15C25 BTBH15C26 BTBH15C27 BTBH15C28 BTBH15C29 BTBH15C30
Package Quantity 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Note: Dust covers and marking strips are supplied with the terminal block.
Specifications Standards Insulation Voltage Wire Size Rated Current Terminal screw Crimping Terminal Max. No. of Crimping Terminals Tightening Torque
UL/CSA 300V 22-14 AWG 10A
BTB15C/BTBH15C EN 500V 2 mm2 (18-14 AWG) 22A M3 1.25-3 (2-3) 2 0.6 to 1.0 N · m
JIS 600V 1.25 mm2 (2 mm2) ∗ 16A
ø3.2 min.
Crimping Terminal Dimensions (mm)
6.6 max.
5 max.
Accessory: Jumper
BNJ36, BNJ36B, BNJ36F, BNJ36FB (see page 43)
∗ The rated applicable wire size is 1.25 mm2, but 2 mm2 wires can also be connected. The wire size in ( ) does not comply with JIS standards.
38
3.3 min.
BTB / BTBH Series Surface Mount Terminal Blocks BTB15LC/BTBH15LC No. of Package Style Part No. Poles Quantity 2 BTB15LC2 1 3 BTB15LC3 1 4 BTB15LC4 1 5 BTB15LC5 1 6 BTB15LC6 1 7 BTB15LC7 1 8 BTB15LC8 1 9 BTB15LC9 1 10 BTB15LC10 1 11 BTB15LC11 1 12 BTB15LC12 1 13 BTB15LC13 1 14 BTB15LC14 1 15 BTB15LC15 1 BTBH15LC BTB15LC 16 BTB15LC16 1 (Touch-down (Self-lifting terminal) terminal) 17 BTB15LC17 1 18 BTB15LC18 1 19 BTB15LC19 1 20 BTB15LC20 1 21 BTB15LC21 1 22 BTB15LC22 1 23 BTB15LC23 1 24 BTB15LC24 1 25 BTB15LC25 1 26 BTB15LC26 1 27 BTB15LC27 1 28 BTB15LC28 1 29 BTB15LC29 1 30 BTB15LC30 1 Note: Dust covers and marking strips are supplied with the terminal block. Style
No. of Poles 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
Part No. BTBH15LC2 BTBH15LC3 BTBH15LC4 BTBH15LC5 BTBH15LC6 BTBH15LC7 BTBH15LC8 BTBH15LC9 BTBH15LC10 BTBH15LC11 BTBH15LC12 BTBH15LC13 BTBH15LC14 BTBH15LC15 BTBH15LC16 BTBH15LC17 BTBH15LC18 BTBH15LC19 BTBH15LC20 BTBH15LC21 BTBH15LC22 BTBH15LC23 BTBH15LC24 BTBH15LC25 BTBH15LC26 BTBH15LC27 BTBH15LC28 BTBH15LC29 BTBH15LC30
Package Quantity 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Specifications Standards Insulation Voltage Wire Size Rated Current Terminal screw Crimping Terminal Max. No. of Crimping Terminals Tightening Torque
UL/CSA 300V 22-14 AWG 15A
BTB15LC/BTBH15LC EN 500V 2 mm2 (18-14 AWG) 22A M3.5 2-3.5 2 1.0 to 1.3 N · m
JIS 600V 2 mm2 21A
ø3.6 min.
Crimping Terminal Dimensions (mm)
8.5 max. 5 max.
Accessory: Jumper
4 min.
BNJ46, BNJ46B, BNJ46F, BNJ46FB (see page 43)
39
BTB / BTBH Series Surface Mount Terminal Blocks BTB30C/BTBH30C Style
BTB30C (Self-lifting terminal)
No. of Poles 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
Part No. BTB30C2 BTB30C3 BTB30C4 BTB30C5 BTB30C6 BTB30C7 BTB30C8 BTB30C9 BTB30C10 BTB30C11 BTB30C12 BTB30C13 BTB30C14 BTB30C15 BTB30C16 BTB30C17 BTB30C18 BTB30C19 BTB30C20 BTB30C21 BTB30C22 BTB30C23 BTB30C24 BTB30C25 BTB30C26 BTB30C27 BTB30C28 BTB30C29 BTB30C30
Package Quantity 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Style
BTBH30C (Touch-down terminal)
No. of Poles 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
Part No. BTBH30C2 BTBH30C3 BTBH30C4 BTBH30C5 BTBH30C6 BTBH30C7 BTBH30C8 BTBH30C9 BTBH30C10 BTBH30C11 BTBH30C12 BTBH30C13 BTBH30C14 BTBH30C15 BTBH30C16 BTBH30C17 BTBH30C18 BTBH30C19 BTBH30C20 BTBH30C21 BTBH30C22 BTBH30C23 BTBH30C24 BTBH30C25 BTBH30C26 BTBH30C27 BTBH30C28 BTBH30C29 BTBH30C30
Note: Dust covers and marking strips are supplied with the terminal block.
Specifications Standards Insulation Voltage Wire Size Rated Current Terminal screw Crimping Terminal Max. No. of Crimping Terminals Tightening Torque
UL/CSA 300V 18-10 AWG 30A
BTB30C/BTBH30C EN 500V 5.5 mm2 (14-10 AWG) 38A M4 1.25-4 to 5.5-4 2 1.4 to 2.0 N · m ø4.2 min.
Crimping Terminal Dimensions (mm)
9.5 max.
6 max.
Accessory: Jumper
40
4.5 min.
BNJ56, BNJ56B, BNJ56F, BNJ56FB (see page 43)
JIS 600V 5.5 mm2 40A
Package Quantity 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
BTB / BTBH Series Surface Mount Terminal Blocks BTB50C/BTBH50C Style
BTB50C (Self-lifting terminal)
No. of Poles 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Part No. BTB50C2 BTB50C3 BTB50C4 BTB50C5 BTB50C6 BTB50C7 BTB50C8 BTB50C9 BTB50C10 BTB50C11 BTB50C12 BTB50C13 BTB50C14 BTB50C15 BTB50C16 BTB50C17 BTB50C18 BTB50C19 BTB50C20
Package Quantity 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Style
BTBH50C (Touch-down terminal)
No. of Poles 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Part No. BTBH50C2 BTBH50C3 BTBH50C4 BTBH50C5 BTBH50C6 BTBH50C7 BTBH50C8 BTBH50C9 BTBH50C10 BTBH50C11 BTBH50C12 BTBH50C13 BTBH50C14 BTBH50C15 BTBH50C16 BTBH50C17 BTBH50C18 BTBH50C19 BTBH50C20
Package Quantity 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Note: Dust cover and marking strips are supplied with the terminal block.
Specifications Standards Insulation Voltage Wire Size Rated Current Terminal screw Crimping Terminal Max. No. of Crimping Terminals Tightening Torque
UL/CSA 600V 16-6 AWG 50A
BTB50C/BTBH50C EN 500V 14 mm2 (10-6 AWG) 67A M5 1.25-5 to 14-5 2 2.6 to 3.7 N · m
JIS 600V 14 mm2 70A
ø5.2 min.
Crimping Terminal Dimensions (mm)
Accessory: Jumper
12.8 max. 6.5 max.
4.5 min.
BNJ62, BNJ62B (page 43)
41
BTB / BTBH Series Surface Mount Terminal Blocks Dimensions • L (Length of the terminal block) and P (mounting hole centers) are nominal dimensions for each terminal block. Because the terminal blocks are combined together with bolts, there may be differences in the dimensions depending on the number of poles combined.
BTB15C/BTBH15C (8.5-mm Terminal Centers) 16A Recommended Tightening Torque: 1.0 N·m
12.5 8.5
Recommended Tightening Torque: 1.0 N·m
M4 Hole
34
M4 Hole
34
6.7
10.5 P L
P L
Dust Cover
Dust Cover
14.5
Dimensions L and P (mm)
Dimensions L and P (mm) No. of Poles
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
No. of Poles
2
3
L
42 50.5 59
L
P
33
41.5
P
37
47.5
No. of Poles
17
18
17
18
L P
67.5 76 84.5 93 101.5 110 118.5 127 135.5 144 152.5 161 50 58.5 67 75.5 84 92.5 101 109.5 118 126.5 135 143.5 152 30
—
No. of Poles
169.5 178 186.5 195 203.5 212 220.5 229 237.5 246 254.5 263 271.5 280 160.5 169 177.5 186 194.5 203 211.5 220 228.5 237 245.5 254 262.5 271
— —
P
19
20
21
M3.5 Terminal Screw
9.5
9.5
14.5
M3 Terminal Screw
28 max.
8.5
M3.5
21A
28 max.
12.5
BTB15LC/BTBH15LC (10.5-mm Terminal Centers)
M3
22
23
24
25
26
27
28
29
L
4
46 56.5 67
5
6
7
8
9
10
11
12
13
14
15
16
88 98.5 109 119.5 130 140.5 151 161.5 172 182.5 193 58 68.5 79 89.5 100 110.5 121 131.5 142 152.5 163 173.5 184 19
77.5
20
21
22
23
24
25
26
27
28
29
30
—
203.5 214 224.5 235 245.5 256 266.5 277 287.5 298 308.5 319 329.5 340 194.5 205 215.5 226 236.5 247 257.5 268 278.5 289 299.5 310 320.5 331
— —
Weight (per pole) BTB15: Approx. 9g BTBH15: Approx. 10g
Weight (per pole) BTB15L: Approx. 12g BTBH15L: Approx. 13g
BTB30C/BTBH30C (12-mm Terminal Centers)
BTB50C/BTBH50C (15.5-mm Terminal Centers)
M4
40A
13.5
Recommended Tightening Torque: 1.0 N·m
13
M5 Hole
48
38
M4 Hole
12
15.5
P L Dust Cover
M5 Terminal Screw 19.3 14
9.5
31 max.
16.4
P L
Dust Cover
M4 Terminal Screw
Dimensions L and P (mm)
Dimensions L and P (mm) No. of Poles
2
3
4
5
6
L P
49 40
61 52
73 64
85 76
97 88
109 121 133 145 157 169 181 193 205 217 100 112 124 136 148 160 172 184 196 208
No. of Poles
17
18
19
20
21
22
L P
7
8
23
9
24
10
25
11
26
12
27
13
28
14
29
15
16
30
—
229 241 253 265 277 289 301 313 325 337 349 361 373 385 220 232 244 256 268 280 292 304 316 328 340 352 364 376
— —
Weight (per pole) BTB30: Approx. 20g BTBH30: Approx. 22g
42
M5
38 max.
12.5 9.6
70A Recommended Tightening Torque: 1.0 N·m
No. of Poles L P No. of Poles L P
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
58 73.5 89 104.5 120 135.5 151 166.5 182 197.5 213 228.5 244 259.5 275 47 62.5 78 93.5 109 124.5 140 155.5 171 186.5 202 217.5 233 248.5 264 17
18
19
20
290.5 306 321.5 337 279.5 295 310.5 326
Weight (per pole) BTB50: Approx. 35g BTBH50: Approx. 40g
BTB / BTBH Series Surface Mount Terminal Blocks Accessories The dust cover and marking strip (fiber) are supplied with the product. Jumpers for 6 Poles (Material: Brass, Plating: Nickel, Insulation: PVC) Insulation Without
Part No.
Ordering No.
BNJ36
BNJ36PN10
BNJ36B
BNJ36BPN10
Ring With
Dimensions (mm)
ø3.7
6.4
8.5
42.5 (6-pole)
BNJ36FB
BNJ36FBPN10
BNJ46
BNJ46PN10
BNJ46B
BNJ46BPN10
R1 6.4 .8 5
With Without
8.2
52.5 (6-pole)
10.5
Insulation
Without
BNJ56
BNJ56PN10
BNJ56B
BNJ56BPN10
2.8
9.3
1.4 0.8
Insulation
12 mm
BNJ56FB
BNJ56FBPN10
Fork With
4.2
9.3
1.4 0.8
.1
R2
1.7
BNJ56FPN10
9.5 5.8
BNJ56F
12
60 (6-pole)
6
Without
BTB30 BTBH30
Insulation
60 (6-pole)
12
6
With
10
0.8
9.5
Ring
1.4
1.7
BNJ46FBPN10
10.5 4.2
.2
With
8.2 R2 .1
52.5 (6-pole)
ø4
BNJ46FB
Fork
30A
0.8
11 4.5
BNJ46FPN10
BTB15L BTBH15L
1.4
.2
ø4
5.5
BNJ46F
10
Insulation
10.5 mm Without
20A
1.4 min.
5.5
With
BTB15 BTBH15
0.8
11
Ring
8.5 3.7
4.5 9 4.5
Fork
10
42.5 (6-pole)
2.8
BNJ36FPN10
20A
Insulation
2
BNJ36F
Package Quantity
1.4 min. 0.8
8.5 mm Without
Applicable Terminal Block
Rated Current
2
Shape
4.5 9
Terminal Center
Insulation
Notes: Jumpers for more than 6 poles are not available.
Jumper for 2 poles Terminal Insulation Centers
Ring Terminal BNJ62
BNJ62PN10
Current (Note 1, 2)
Dimensions
Without 14.5 mm
BNJ62B
BNJ62BPN10
Applicable Terminal Block
Package Quantity
s)
Ordering No.
(h ol e
Part No.
BTB50 BTBH50
80A
10
With
•• Material: nickel-coated brass •• Sheath: PVC Note 1: Ensure that the total current to the jumper does not exceed the maximum current. Note 2: Ensure that the current does not exceed the rated current of the terminal block to be used.
Marking Strip (Supplied with the terminal block. Order as spare parts when necessary) Applicable Terminal Block BTB/BTBH (all models)
Part No. BNM9
Ordering No. BNM9PN10
Material Fiber strip (matte surface)
Size
Package Quantity
1000 mm × 9.5 mm × 0.5 mm
10
Dust Cover (Supplied with the terminal block. Order as spare parts when necessary) Applicable Terminal Block BTB15C/BTBH15C BTB15LC/BTBH15LC BTB30C/BTBH30C BTB50C/BTBH50C
Ordering No.
Material
Length
Package Quantity
BTB-CV15L1
Polycarbonate
500 mm
1
BTB-CV30L1 BTB-CV50L1
Polycarbonate Polycarbonate
500 mm 500 mm
1 1
43
BTB / BTBH Series Surface Mount Terminal Blocks Safety Precautions Notes on Wiring Crimping Terminals • When using crimping terminals, be sure to use insulated terminals to prevent electric shocks. Without Crimping Terminals • Insert the wire until the insulation comes into contact with the terminal metal part. • Strip the insulation so that the wire is longer than the width of the wire clamp. • When connecting two wires, use wires of the same length. • To prevent damage, ensure to use plain washers when installing.
44
Washer Width
Terminal Metal Part
Wire Insulation
BD Series Terminal Blocks Space-saving miniature terminal blocks. Surface mount and DIN rail mount available. • Surface mount terminal blocks available. • Rail mount can be mounted on 15-mm-wide DIN rails. • BD8 rail mount available in black or blue color. • Flame-resistant plastic (UL94V-0). • Can be mounted on the rail easily. • Space-saving low profile style • Safe robust construction • Complies with JIS C 2811. • UL recognized and CSA certified. Applicable Standards
Mark
UL1059
Certification Organization/ File No. UL recognized File No. E78117 CSA (File No. LR64803)
CSA 22.2 No. 158
Rail Mount Terminal centers
8 mm
7 mm 5 mm
BD8-RB BD8-RS BD8S-RB BD8S-RS
BD8-RBPN50 BD8-RSPN50 BD8S-RBPN50 BD8S-RSPN50
Housing Color Black Blue Black Blue
BD7-RB
BD7-RBPN50
Black
BDK5-RB
BDK5-RBPN50
Black
Terminal Shape
Part No.
M3 screw (self-lifting) M3 screw / solder (self-lifting) M3 screw (self-lifting) M3 cage screw
Ordering No.
Wire Size
1.25 mm2 (2 mm2) ∗
Package Quantity 50 50 50 50 50
1.25 mm2
50
∗T he applicable rated wire size is 1.25mm , but 2mm wire can also be connected. The wire size in ( ) does not comply with JIS standards. 2
2
Accessories
Tightening Torque for Terminal Screw
× × × ×
× × × × 50
× × × × 51
Terminal Jumper
End Clip
Marking Strip
Dust Cover
Rail
Part No. BD8-R BD8S-R BD7-RB BDK5-RB
End Plate
Accessories (sold separately)
—
For safe use of the terminal blocks, tighten the screw as shown below. Terminal Screw Recommended Tightening Torque
M3 0.6 to 1.0 N·m
Material Parts Name Housing Terminal Metal Part Terminal Metal Part (BD8S only) Terminal Screw
Material Modified PPE Brass (nickel-plated) Brass (tin-plated) Steel (zinc chromate-plated)
Page ×: Accessories needed when mounting terminal blocks. Order seperately. : Order if necessary. ••Order a dust cover, marking strip (fiber), and jumper when necessary (see page 50 and 51).
45
BD Series Terminal Blocks Surface Mount Terminal centers
Part No. (: No. of Poles)
Terminal Shape
Housing Color
No. of Poles
Wire Size
8 mm
M3 screw (self-lifting)
BD8-MB
Black
2 to 35
1.25 (2) mm2 ∗
8 mm
M3 screw/solder (self-lifting)
BD8S-MB
Black
2 to 35
1.25 (2) mm2 ∗
7 mm
M3 screw (self-lifting)
BD7-MB
Black
2 to 40
1.25 (2) mm2 ∗
5 mm
M3 cage clamp
BDK5-MB
Black
2 to 56
1.25 mm2 ∗
∗ The rated applicable wire size is 1.25 mm , but 2 mm wires can also be connected. 2
2
Ordering Information When ordering, specify the Part No. and the number of poles required. Dust covers and marking strips are supplied with terminal blocks.
Material Parts Housing Terminal Metal Part Terminal Metal Part (BD8S) Terminal Screw
Material Modified PPE Brass (nickel-plated) Brass (tin-plated) Steel (zinc chromate-plated)
Accessories • Dust covers and marking strips are supplied with the terminal block. • Order jumpers if required (see page 51).
46
BD Series Terminal Blocks Terminal Centers Part No. (Specify a color code in place of ∗.)
8 mm Terminal Centers BD8-R∗ (Self-Lifting)
M3
30
13.4
21.5
16A
30
21.5
M3
13.4
Rail Mount
16A
BD8S-R∗ (Screw / Solder)
8 1.3
Part No. (Specify the no. of poles in place of .)
8 6.7
1.3
BD8-MB (Self-Lifting) 16A
BD8S-MB (Screw / Solder)
M3
30 (32) 21.5 (22.5)
21.5 (22.5)
M3
16A
30 (32)
Surface Mount
6.7
P L
P L
8 1.3
8 6.7
1.3
6.7
The length in ( ) includes dust cover. For lengths of P/L, see Surface Mount Dimensions on page 49.
The length in ( ) includes dust cover. For lengths of P/L, see Surface Mount Dimensions on page 49.
Specifications
Ratings
Standards Insulation Voltage
UL/CSA
Rated Current ∗2 Dielectric Strength Insulation Resistance Operating Temperature Storage Temperature Operating Humidity
300V ∗1 15A
14-20 AWG (solid wire/ stranded wire)
Wire Size Terminal Screw
JIS UL/CSA 380V 300V ∗1 16A 15A 2500V AC, 1 minute 100 MΩ minimum –25 to +55°C (no freezing) –25 to +70°C (no freezing) 45 to 85% RH (no condensation) 14-20 AWG 1.25 mm2 (solid wire/ 2 (2 mm ) ∗3 stranded wire) M3
JIS 250V 16A
1.25 mm2 (2 mm2) ∗3
Accessories
Others
ø3.2 min.
Crimping Terminal
6.5 max. 5.6 max.
Maximum No. of Crimping Terminals Housing Color (color code) Weight End Plate (for rail mount) Rail (for rail mount)
15-mm-wide DIN Rail
Dust Cover PVC (glossy surface) Marking Strip Fiber Glass (matte surface) End Clip (for rail mount) Jumper
3.4 min.
2 1 Black (B), Blue (S). Only black available for surface mount terminal blocks 4.8g (per pole) BDE11∗ (see page 50) BDA1000 (aluminum) (see page 50) BDP1000 (steel) (see page 50) BDC1000 (see page 50) BDM11 (see page 51) BDM12 (see page 51) BDL11 (see page 51) BNJ26W, BNJ26WB, BNJ26FW, BNJ26FWB (see page 51)
∗1: The rated voltage when power is applied is 250V under UL recognition. (Example: Office automation equipment, home electric appliances, facsimile, and other information processing equipment.) ∗2: The rated current differs according to operating conditions. See “Selecting Terminal Blocks by Current According to JIS Standards” on page 4. ∗3: The wire size in ( ) does not comply with JIS standards. ∗ Color code: B (black), S (blue)
47
BD Series Terminal Blocks Terminal Centers Style
7-mm Terminal Centers BD7-RB (Self-Lifting) 14A
5-mm Terminal Centers BDK5-RB (Cage Clamp)
M3
M3
14A
22
7
21
5
6
2.1
2.7
1
12.5
12.6
21
Rail Mount
22
Part No. (Specify the no. of poles in place of )
BD7-MB (Self-Lifting) 14A
BDK5-MB (Cage Clamp)
M3
22 (24)
21 (22)
22 (24)
21 (22)
Surface Mount
M3
14A
P L
P L 5
The length in ( ) includes dust cover. For lengths of P/L, see Surface Mount Dimensions on page 49.
6
The length in ( ) includes dust cover. For lengths of P/L, see Surface Mount Dimensions on page 49.
2.7
7 1
Specifications
Ratings
Standards Insulation Voltage
UL/CSA
Rated Current ∗2 Dielectric Strength Insulation Resistance Operating Temperature Storage Temperature Operating Humidity
JIS UL/CSA 250V 300V ∗1 14A 10A 2500V AC / 1 minute
300V ∗1 10A
100 MΩ or more –25 to +55°C (no freezing) –25 to +70°C (no freezing) 45 to 85% RH (no condensation) 16-20 AWG (solid wire/ stranded wire)
Wire Size
Others Accessories
1.25 mm2
M3 ø3.2 min.
Crimping Terminal
Recommended stripping length of the wire cage
5.9 max.
Maximum No. of Crimping Terminals Housing Color Weight (approx.) End Plate (for rail mount) 15-mm-wide DIN Rail
Dust Cover PVC (smooth surface) Fiber Glass (rough surface) End Clip (for rail mount)
6
3.2 min.
4.5 max.
Marking Strip
16-20AWG (solid wire)
1.25 mm2 (2 mm2 max) ∗3
Terminal Screw
Rail (for Rail Mount)
JIS 250V 14A
2
1 Black
3.6g (per pole)
3.4g (per pole) BDE12B (see page 50) BDA1000 (aluminum) (see page 50) BDP1000 (steel) (see page 50) BDC1000S (see page 50) BNM8 (see page 51) BNM10 (see page 51)
BDL11 (see page 51) BDJ10, BDJ10B, BDJ10F, BDJ10FB Jumper — (see page 51) ∗1: The rated voltage when power is applied is 250V under UL recognition. (Example: Office automation equipment, home electric appliances, facsimile, and other information processing equipment.) ∗2: The rated current differs according to operating conditions. See “Selecting Terminal Blocks by Current According to JIS Standards” on page 4. ∗3: The wire size in ( ) does not comply with JIS standards.
48
2.1
BD Series Terminal Blocks Surface Mount Dimensions • L (Length of the terminal block) and P (mounting hole centers) are nominal dimensions for each terminal block. Because the terminal blocks are combined together with bolts, there may be differences in the dimensions depending on the number of poles combined.
M3 Terminal Screw Recommended Tightening Torque: 1.0 N·m
M4 Hole
M3 Terminal Screw Recommended Tightening Torque: 1.0 N·m
M4 Hole
18 30
4.3
15
6
BD7-MB (7-mm Terminal Centers)
22
BD8-MB (8-mm Terminal Centers)
P L
P L Dust Cover
3
4
5
37.9 29.9
45.85 37.85
53.8 45.8
61.75 53.75
16
18
20
25
149.2 141.2
165.1 157.1
181 220.75 173 212.75
6
8
69.7 85.6 61.7 77.6
10
12
101.5 93.5
117.4 109.4
14
15
133.3 141.25 125.3 133.25
30
35
Calculation Formula
260.5 252.5
300.3 292.3
L = 22 + (7.95n)±0.5 P =14 + (7.95n)±0.5
Weight (per pole): 4.8g (BD8) n = number of poles
BD8S-MB (8-mm Terminal Centers)
3
4
5
42.7 34.7
49.6 41.6
56.5 48.5
No. of Poles L P
16
18
20
25
30
132.4 124.4
146.2 138.2
160 152
194.5 186.5
229 221
14
15
118.6 110.6
125.5 117.5
35
40
Calculation Formula
263.5 255.5
298 290
L = 22 + (6.9n)±0.5 P = 14 + (6.9n)±0.5
15
30
18
12 104.8 96.8
M3 Terminal Screw Recommended Tightening Torque: 1.0 N·m
M4 Hole
Dust Cover
5 3 8
7.5
12.4
21
8
22.5
8 3
21.5
8
Dimensions L and P (mm)
2
3
4
5
37.9 29.9
45.85 37.85
53.8 45.8
61.75 53.75
16
18
20
25
149.2 141.2
165.1 157.1
181 220.75 173 212.75
Weight (per pole): 4.8g (BD8) n = number of poles
10 91 83
P L
Dimensions L and P (mm)
No. of Poles L P
8
BDK5-MB (5-mm Terminal Centers)
7.5
13.1
Dust Cover
6
63.4 77.2 55.4 69.2
Weight (per pole): 3.6g (BD7) n = number of poles
P L
No. of Poles L P
22
21
2 35.8 27.8
M3 Terminal Screw Recommended Tightening Torque: 1.0 N·m
M4 Hole
4.3
6
No. of Poles L P
22
2
22
No. of Poles L P
7.5
Dimensions L and P (mm)
Dimensions L and P (mm) No. of Poles L P
7 3 8
12.5
22.5
21.5
8
8 3 8
7.5
13.3
Dust Cover
6
8
69.7 85.6 61.7 77.6
10
12
14
15
101.5 93.5
117.4 109.4
133.3 125.3
141.25 133.25
30
35
Calculation Formula
260.5 252.5
300.3 292.3
L = 22 + (7.95n) P = 14 + (7.95n)±0.5 ±0.5
No. of Poles L P No. of Poles L P No. of Poles L P
2
3
4
5
31.9 23.9
36.9 28.9
41.8 33.8
46.8 38.8
16
18
20
25
101.2 93.2
6
51.7 61.6 43.7 53.6 30
111.1 121 145.8 103.1 113 137.8
52
53
54
279.4 271.4
284.35 276.35
289.3 281.3
8
170.5 162.5
55
35
10
12
14
15
71.5 63.5
81.4 73.4
91.3 83.3
96.3 88.3
45
50
51
40
195.3 220 244.8 187.3 212 236.8 56
294.25 299.2 286.25 291.2
269.5 274.5 261.5 266.5
Calculation Formula L = 22 + (4.95n)±0.5 P = 14 + (4.95n)±0.5
Weight (per pole): 3.4g (BDK5) n = number of poles
49
BD Series Terminal Blocks Accessories End plate
Marking Strip
Marking Strip Dust Cover Dust Cover End plate
Shape
Part No.
Ordering No.
Black BDE11B
BDE11BPN10
Package Quantity
Dimensions
Remarks
21.5
8-mm terminal centers
Blue
BDE11S
BDE11SPN10
3
30
Material: Modified PPE 7-mm, 5-mm terminal centers
Black BDE12B
BDE12BPN10
• Used for ends of terminal blocks. For use on: BD7-RB BDK5-RB • Weight: 1g
21
End Plate
10
• Used for ends of terminal blocks. For use on: BD8-R∗ BD8S-R∗ • Weight: 1g
10
22
3
Material: Modified PPE DIN Rail 15-mm wide Aluminum, Length: 1m
12.5
1 15
10 5.5
BDP1000PN10
12.5
28
10
31.7
BDC1000PN10
• Transparent plastic cover for terminal blocks. For use on: BD8-R∗ BD8-MB BD8S-R∗ BD8S-MB
20
3.8
BDC1000
• Transparent plastic cover for terminal blocks. For use on: BD7-RB∗ BD7-MB BDK5-RB∗ BDK5-MB
1000
Polycarbonate, Length: 1m 7-mm, 5-mm terminal centers 3.8
BDC1000S
BDC1000SPN10
23.7
Dust Cover
5
1000
8-mm terminal centers
• DIN rail for mounting terminal blocks. For use on: BD8-R∗ BD8S-R∗ BD7-RB BDK5-RB
10.5
8
BDP1000
10 1000
Polycarbonate, Length: 1m
Specify the color code in place of ∗. B (black), S (blue) : Number of poles
50
5
1000
8.5
Rail
DIN Rail 15-mm wide Steel, Length: 1m
12.8
10
8.5
BDA1000PN10
5.5
BDA1000
15
8
BD Series Terminal Blocks Material
8-mm terminal centers
PVC (glossy surface)
Part No. BDM11
Package Quantity
Ordering No. BDM11PN10
Dimensions (mm)
Terminal Block
10
BD8-R∗ BD8-MB BD8S-R∗ BD8S-MB
7.5
Shape
Marking Strip
1000
7-mm, 5-mm terminal centers
Fiber glass (matte surface)
BDM12
BDM12PN10
10
PVC (glossy surface)
BNM8
BNM8PN10
10
t = 0.5
Fiber glass (matte surface)
BNM10
BNM10PN10
BD7-RB BD7-MB BDK5-RB BDK5-MB
5.5
1000
t = 0.5
10
Steel (zinc-plated)
14.2
End Clip
M3 Screw
BDL11
BDL11PN10
10
20.4
8.5
Weight: Approx. 4g
BD8-R∗ BD8S-R∗ BD7-RB BDK5-RB
Recommended tightening torque: 0.5 to 0.7 N·m
BNJ26WPN10
BNJ26FWPN10
R1
.8
BNJ26FWBPN10
BDJ10
BDJ10PN10
For 10-pole 7-mm Terminal Centers
8
6.4
40 (6-pole)
10
1.4
3.7
0.8
BD8-R∗ BD8-MB BD8S-R∗ BD8S-MB
20A 10
Insulation
63 (10P)
BDJ10F
BDJ10FPN10
BDJ10FB Insulation: PVC
BDJ10FBPN10
1.4 min. 0.5
7
4 7
5.7 ø3. 7
BDJ10BPN10
Fork Material: Brass (nickel-plated)
10
Dashed lines: Insulation
Ring BDJ10B Insulation: PVC
5
0.8
10 10A
Sheath
10
Dashed lines: Insulation
3.7
5.7
4 7 3.7
Jumper
Material: Brass (nickel-plated)
20A
Dashed lines: Insulation
Fork BNJ26FWB Insulation: PVC
2
BNJ26FW
Applicable Terminal Block
10
0.8
Insulation
Package Quantity
2
BNJ26WBPN10
1.4
4.5 11 4.5
For 6-pole 8-mm Terminal Centers
40 (6P)
8
6.4 ø3. 7
Ring BNJ26WB Insulation: PVC
Rated Current
Dimensions
7
63 (10P)
BD7-RB BD7-MB 1.4 min. 0.8
10 10A
0.5
BNJ26W
Ordering No.
11
Part No.
4
Description
10
Insulation
Dashed lines: Insulation
Calculating the Rail Length (When the same type terminal block is mounted) BDA and BDP Rails L1 = 12.5 × N L2 = L1 – 25
Mounting Hole
N: Rounded up numerical number from the calculated value of M. (Example: N for 19.1 is 20) M=
(A + 0.1) n + 68.5 12.5
A: Thickness of each terminal block n: The number of terminal blocks Note: This formula is for calculating the maximum rail length including tolerance. Depending on the combination of terminal blocks, the required rail length may be shorter than the calculated value, particularly when many terminal blocks are combined.
L2 L1
51
BD Series Terminal Blocks Instructions Installation of Rail Mount Terminal Blocks End Plate
Rail
End Clip
When using DIN Rail 1. Determine the length of the DIN rail according to the width of the terminal blocks. 2. Assemble the terminal blocks with an end plate on one side, and then install them onto the DIN rail. (When mounting BD8, BD7, and BDK5 series on the same DIN rail, use end plates at the end of assemblies of each series. 3. Install a end clip (BDL11) so that the terminal blocks are mounted in the center of the DIN rail. See “Installing the end clip” below. 4. Insert the marking strip and fasten with another end plate. 5. Install the end clip (BDL11) on the other end of the terminal block 6. Cover the terminal block with the dust cover. Installing the end clip Stamped Side
Marking Strip Push the end clip on the DIN rail.
Hook the stamped side of the end clip on the DIN rail. End Clip
Slide the end clip to the stamped side and tighten the screw. Recommended tightening torque: 0.8 N·m
Installing Surface Mount Terminal Blocks To install surface mount terminal blocks, use four screws and tighten four corners of the terminal blocks to a torque of 1.0 N·m maximum. For screw types and tightening torque, see the table below. See page 49 for mounting hole dimensions.
Installing and Removing the Marking Strip When removing the marking strip, pull out the end of the marking strip with the tip of a screwdriver. To install, insert the marking strip into the terminal block from one end and press in the other end of the marking strip.
Pull out this end. Press lightly to insert.
Screw Size (For BD8) M4 screw only M4 screw + M4 plain washer
M4 screw + M4 plain washer + M4 spring washer
Screw Size (For BD/BDK5) — M3 screw + M3 plain washer M3.5 screw + M3.5 plain washer
Tightening Torque
M3 screw + M3 plain washer+ M3 spring washer
1.0 N·m maximum
M3.5 screw + M3.5 plain washer + M3.5 spring washer
Notes on Wiring
Washer Width
Crimping Terminals • When using crimping terminals, be sure to use insulated terminals to prevent electric shocks. Without Crimping Terminals • Insert the wire until the insulation comes into contact with the terminal metal part. • Strip the insulation so that the wire is longer than the width of the wire clamp. • When connecting two wires, use wires of the same size.
Terminal Metal Part
Wire Insulation
Specifications and other descriptions in this brochure are subject to change without notice. 6-64, Nishi-Miyahara 2-Chome, Yodogawa-ku, Osaka 532-0004, Japan Tel: +81-6-6398-2571, Fax: +81-6-6392-9731, E-mail:
[email protected]
IDEC CORPORATION (USA)
Tel: +1-408-747-0550 / (800) 262-IDEC (4332) E-mail:
[email protected]
IDEC CANADA LIMITED
IDEC ELEKTROTECHNIK GmbH
IDEC IZUMI (H.K.) CO., LTD.
IDEC (SHANGHAI) CORPORATION
IDEC TAIWAN CORPORATION
Tel: +49-40-25 30 54 - 0 E-mail:
[email protected] Tel: +86-21-6135-1515 E-mail:
[email protected]
Tel: +1-905-890-8561, Toll Free: (888) 262-IDEC (4332) IDEC (BEIJING) E-mail:
[email protected] Tel: +86-10-6581-6131
IDEC AUSTRALIA PTY. LTD.
www.idec.com
Tel: +61-3-8523-5900, Toll Free: 1800-68-4332 E-mail:
[email protected]
CORPORATION
Tel: +852-2803-8989 E-mail:
[email protected] Tel: +886-2-2698-3929 E-mail:
[email protected]
IDEC IZUMI ASIA PTE. LTD.
Tel: +65-6746-1155 E-mail:
[email protected]
IDEC (SHENZHEN) CORPORATION IDEC ASIA (THAILAND) CO.,LTD. Tel: +86-755-8356-2977
Tel: +662-392-9765, E-mail:
[email protected]
Cat. No. EP1451-4 OCTOBER 2016 PDF