TM
Brief Product Descriptions
Imperial Oil Downstream and Chemical 237 Fourth Avenue SW, Calgary, Alberta T2P 3M9
2015 Edition – Canada
For more information: 1- 888-968-3776
Brief Product Descriptions
mobil.ca mobildelvac.ca mobilindustrial.com All trademarks used herein are trademarks or registered trademarks of Exxon Mobil Corporation or one of its subsidiaries.
2015 Edition – Canada
TM
TM
TM
TM
TM
TM
TM
TM
TM
TM
Brief Product Descriptions 2015 Edition
237 Fourth Avenue SW, Calgary, Alberta T2P 3M9 For additional information please call our Technical Support Centre at 1 888 968-3776 or visit mobil.ca Due to ongoing product research and development, the information herein is subject to change without notification. Please refer to our Product Data Sheets found at mobil.ca/pds for the most current product information.
2
INTRODUCTION This book is provided as a field reference to our core product offer of lubricating oils, greases and coolants. The format is designed to help you choose precisely the right product for each application. The content is divided into six sections: Industrial Commercial Vehicle Passenger Vehicle Marine Aviation Grease Within each section, products are divided into application groups. An alphabetical list of applications is provided up front and an alphabetical index of products is located at the end. An appendix provides additional information.
Typical Properties are typical of those obtained with normal product tolerance and do not constitute a specification. Variations that do not affect product performance are to be expected during normal manufacture and at different blending locations. All products may NOT be available locally. For additional information please call our Technical Support Centre at 1 888 968-3776 or visit mobil.ca.
Due to continual product development, these contents are subject to change without notification. Please refer to our Product Data Sheets found at mobil.ca/pds for the most current product information.
1
Visit mobil.ca /pds for the most current product information
The Ultimate Lubrication Warranty Imperial will repair or replace any piece of your equipment damaged due to the failure of our lubricant.
All our lubricants meet or exceed original equipment manufacturers’ standards. We guarantee their performance when used in accordance with Imperial’s recommendations, the equipment manufacturers’ performance specifications, and under normal operating conditions. This warranty is in addition to any and all original equipment manufacturers’ warranties and does not invalidate them. Because we are 100% committed to you, we stand behind our lubricants 100%.
See next page for complete warranty terms and conditions. For further information on the Imperial Ultimate Lubrication Warranty or any Mobil lubricant call Imperial at 1 888 968-3776.
TM
TM
TM
TM
TM
TM
TM
TM
TM
All trademarks used herein are trademarks or registered trademarks of Exxon Mobil Corporation or one of its subsidiaries. Limitation of liability: in no event shall Imperial Oil be liable for any incidental, indirect, special, exemplary, punitive or consequential damages, including loss of profits.
2
Pegasus Pegasus Pegasus
The Ultimate Lubrication Warranty Terms and Conditions What the Warranty Covers
What the Warranty Does Not Cover
Imperial provides this warranty to direct purchasers of Mobil™ lubricants, where such lubricants have been purchased from an authorized vendor. This warranty covers the Mobil product and critical equipment parts lubricated by that product directly damaged by a defect or malfunction of the lubricant. Imperial warrants that its lubricants are free from defects and that the lubricant you purchased will protect your equipment parts from oil related failure for three years, provided that:
This warranty excludes: • Mobil lubricants used in mechanically deficient equipment, where the deficiency results from, but is not limited to: a previously existing condition, abnormal operation; negligence; abuse; damage from casualty, shipment or accident; or equipment modification done without written authorization from the OEM.
• The equipment was in good operating condition at the time the lubricant was installed;
• Mobil lubricants used in equipment where the OEM required lubricant standards do not match those stated by Imperial, without prior written approval from Imperial.
• The lubricant was selected and maintained in accordance with specifications of the original equipment manufacturer (“OEM”), and the written recommendations (which include product packaging) provided by Imperial at the time of sale; and
• Mobil lubricants and/or equipment pieces that have been used in conjunction with any other product or additive that has not been authorized for use by Imperial.
• The equipment has been operated within the limits specified by the OEM. Be advised that if your equipment is covered by a manufacturer’s warranty, you should follow the equipment’s oil life sensor and the oil change interval recommended in your owner’s manual to avoid a disruption in the manufacturer’s warranty. Follow your owner’s manual if the equipment is operated in any of the following severe services: racing or commercial applications including taxis, limousines, etc.; frequent towing or hauling; extremely dusty or dirty conditions; or under excessive idling conditions.
What the Period of Coverage Is The Ultimate Lubrication Warranty is valid for three (3) years from the date of purchase or installation, whichever comes first.
What We Will Do to Correct Problems Imperial will replace any lubricant that is defective. In addition, Imperial will repair any equipment damage directly caused by a defect or malfunction of the lubricant, at no cost to you, provided that the lubricant was selected and maintained in accordance with specifications of the OEM and the written instructions (which includes product packaging) provided by Imperial. These are your exclusive remedies for any claim for defective lubricant.
3
• Failure of equipment due to non-lubricant related conditions, such as normal wear.
How You Can Get Service To file a claim under this warranty, you must: 1. Within 48 hours from discovery of the damage (and not later than six (6) months from the date the damage occurred), call 1-888-968-3776 to communicate the issue, and initiate a claims investigation. You may also contact your Imperial or local Distributor representative.* 2. Provide proof of purchase and maintenance records showing that the equipment was serviced at the intervals recommended by the OEM. 3. Allow an Imperial representative to examine the equipment to determine the extent of the damage and to confirm that the lubricant was the cause. 4. Allow an Imperial representative to obtain an oil sample, if available, from the engine for oil analysis at no cost to you to assist in determining the cause of the equipment failure.
TABLE OF CONTENTS Introduction........................................................................................................................ 1 Ultimate Lubrication Warranty.......................................................................................2-3 Health and Safety Precautions......................................................................................5-7 Sustainability..................................................................................................................... 8 Energy Efficiency............................................................................................................... 9 Application Index of Products................................................................................... 10-11 Mobil SHC™ General Recommendations..................................................................... 12
Brief Product Descriptions...................................................................................... 14-104
Appendices............................................................................................................. 105-109 Temperature Conversion Table................................................................................. 105-106 Viscosity Conversion Table.............................................................................................. 107 Viscosity - Temperature Chart......................................................................................... 108 SAE Viscosity Grades for Engine Oils............................................................................. 109 SAE J306 Viscosity Grades for Gear Oils....................................................................... 109 Classification of Greases by National Lubricating Grease Institute (NLGI) Consistency Numbers.......................................................................................... 109 Understanding Oil Analysis...............................................................................................110 ANSI-AGMA Industrial Gear Lubricants 9005-D94.......................................................... 111
Alphabetical List of Products................................................................................. 112-116
Viscosity Classification Equivalents............................................................................117
QUESTIONS? CALL OUR TECHNICAL SUPPORT CENTER AT
1 888 968-3776 mobilindustrial.com | mobildelvac.ca | mobil.ca
Visit mobil.ca /pds for the most current product information
4
HEALTH AND SAFETY PRECAUTIONS Workplace Hazardous Materials Information System (WHMIS) The Workplace Hazardous Materials Information System or WHMIS is designed to ensure that all employers obtain the information they need to inform and train their employees properly about hazardous materials used in the workplace. WHMIS was developed through extensive consultation with industry and labour representatives and the federal, provincial and territorial governments. The goal of WHMIS is to reduce the incidence of illness and injuries resulting from the use of hazardous materials in the workplace. Through legislation, the WHMIS consensus establishes uniform requirements to ensure that the hazards of materials produced or sold in, imported into or used within workplaces in Canada are identified by suppliers and employers using standard classification criteria. WHMIS provides employers and workers with one additional tool to improve their understanding of hazardous materials.To make the best use of this tool, suppliers and employers have certain responsibilities. A ‘supplier’ is a manufacturer, processor or packager of a controlled product or a person who, in the course of business, imports or sells controlled products. A ‘controlled product’ is defined for WHMIS under the federal Hazardous Product Act as any product, material or substance specified by the regulations included in any of the classes listed in Table 1 (see page 6). An ‘employer’ is, for the purposes of WHMIS, the user of a controlled product in the workplace or the producer of a controlled product as part of a workplace process.
Under occupational safety and health legislation, employers are also required to provide their employees with hazard information received from their suppliers with respect to controlled products used or produced in the workplace, by means of appropriate workplace labels, by distributing MSDS and by providing worker education on the safe use of hazardous materials. WHMIS is designed to ensure that all employers receive the information they need to educate and train their employees properly in the use of hazardous materials in the workplace. It will also provide employees with necessary hazard information so they can participate in, and support, the precautionary measures instituted in their workplaces. As a supplier of petrochemical products in Canada, Imperial Oil has issued material safety data sheets for all Imperial Oil products and prepared labels that comply with WHMIS for all controlled products. Controlled products can be easily identified because of the special WHMIS supplier label. Material Safety Data Sheets should be consulted prior to handling a product to ascertain whether there are any specific health and safety risks or special handling requirements that should be addressed. Imperial Oil will continue to investigate the potentially hazardous properties of existing and new materials through extensive testing and research programs.
Suppliers must convey hazard information to purchasers in a specified manner by means of labelling of the controlled products or containers of the controlled products, and by providing more detailed information concerning the controlled product in the form of a Material Safety Data Sheet (MSDS).
5
Visit mobil.ca /pds for the most current product information
HEALTH AND SAFETY PRECAUTIONS
Material Safety Data Sheets
Product Handling
What kind of information does an MSDS provide?
Most lubricating oils and greases are not controlled under WHMIS legislation in Canada. However, certain basic handling procedures should be observed to keep the petroleum products off the skin and to avoid inhalation of their vapours and mists. The following guidelines apply to the handling of all petroleum products and in general to other chemicals with which you may come in contact.
An MSDS typically contains the following types of information: • Physical data on the product (e.g. viscosity, flash point) • The nature and degree of health, environmental and safety hazards associated with the product • Precautionary guidelines for proper and safe handling of the product in order to avoid fire, explosion and acute and chronic health hazards • Emergency procedures in the event of fire, spill or excessive exposure to the product by skin contact, ingestion or inhalation Imperial Oil customers in Canada can obtain Material Safety Data Sheets (MSDS) and Workplace Hazardous Materials Information System (WHMIS) information, in English or French, for all products. Through the customer-establishment process, customers of WHMIS-controlled products will receive a Material Safety Data Sheet (MSDS) on or before first shipment of the controlled product. Subsequent updates to that sheet are directed to the identified customer contact.
Always remember to: • Minimize skin contact with whatever product you are using. • Remove oils from the skin promptly, using mild nonabrasive soap and warm water or a skin cleanser and warm water. • Do not use gasoline, solvents, kerosene or similar products to remove oil or grease from the skin. • Do not wear oil-soaked clothing. Launder all work clothes frequently. Put oily rags in the correct container. Discard oil-soaked shoes and belts. • Wash hands and face thoroughly before eating and at the end of a shift. Take a shower if possible before leaving work. • Clean up spilled product promptly and dispose of it correctly. Keep product out of sewers and waterways.
MSDS are also available through any of the following options:
• Get first aid for all cuts and scrapes and report as required.
• Visit our website at www.imperialoil.ca/msds.
• Avoid inhalation of oil mist and solvent vapours.
• Use our automated ‘FAX-BACK’ system: call 1-800-IOL-MSDS or 1-800-465-6737. Please have your fax number available.
• Obtain medical advice on all potential health-hazard problems.
• Call 1-888-968-3776 to speak to a customer service representative.
One of the least recognized, yet most serious, workplace hazards is a punctured oil line under pressure. When a jet of pressurized fluid makes contact with the skin, it can enter the body and cause serious injury. That is why, under absolutely NO circumstances, should you try to stop a hydraulic oil leak with your finger. Always be aware of the risk when you’re working near hydraulic equipment and if your skin is struck by pressurized fluid, seek medical attention immediately.
• Contact your Imperial sales representative In addition, our technical sales representatives can assist in providing information on the safe storage and use of Imperial Oil products. Special customer requests will be directed to our industrial hygiene/ product safety department.
Visit mobil.ca /pds for the most current product information
6
HEALTH AND SAFETY PRECAUTIONS Table 1 – WHMIS Class and Division Hazard Symbols CLASS AND DIVISION DESIGNATION
SYMBOL
CLASS A – Compressed Gas
CLASS B – Flammable and Combustible Material
Flammable Gas Flammable Liquid Combustible Liquid Flammable Solid Flammable Aerosol Reactive Flammable Material
CLASS C – Oxidizing Material
CLASS D – Poisonous and Infectious Material 1. M aterial causing immediate and serious toxic effect
2. Material causing other toxic effects
3. Biohazardous infectious material
CLASS E – Corrosive Material
CLASS F – Dangerously Reactive Material
7
Visit mobil.ca /pds for the most current product information
SUSTAINABILITY
The three pillars of Advancing Productivity serve as part of our corporate commitment to sustainability. At ExxonMobil, “sustainability” means balancing economic growth, social development and environmental protection so that future generations are not compromised by actions taken today. To put sustainability in motion, we take a holistic approach across our offer, communication and process, providing innovative lubricants and services that can create tangible value for you in the areas of safety, environmental care and productivity. Through Advancing Productivity, our goal is to deliver performance benefits in these three crucial areas of your business so that you can achieve your full vision of success. *
Safety
Environmental Care
Productivity
Minimizing employee – equipment interaction
Designed to help lighten environmental touch
Controlling costly downtime and delays
We offer products and services that can help you mitigate potential
Our commitment to minimizing environmental impact has led us
Enhancing the competitive potential of our customers is an important
employee injury caused by direct contact with equipment. These
to create technologically advanced products and innovative services with
part of Advancing Productivity. We achieve this objective through
products and services are designed to help:
that goal in mind. We strive to help you achieve this goal through:
lubrication solutions that can help provide:
• Provide long drain intervals and
• Optimized oil drain intervals, which
enhance equipment reliability, minimizing maintenance, repair
can help reduce used oil volume and product packaging, as well as
• Long drain intervals, which can help improve equipment availability,
and replacement • Reduce the potential for leaks
service-related risks • Long component life, to help reduce
that arise from handling used oil and related products • Increase employee safety
worn equipment disposal and maintenance-related waste • Potential GHG emissions reduction
awareness and knowledge of a
and other energy-efficiency benefits
lubricant’s effect on health and safety • Address the risk of potential product misapplication
reduce lubricant transaction frequency and minimize disposal costs • Powerful equipment protection, which can maximize equipment availability, helping you control costs of equipment maintenance and replacement • Inventory consolidation potential
*Visit mobilindustrial.com to learn how certain Mobil-branded lubricants may provide benefits to help minimize environmental impact. Actual benefits will depend upon product selected, operating conditions, and applications.
Visit mobil.ca /pds for the most current product information
8
ENERGY EFFICIENCY About the Energy Efficiency Seal As the supplier of Mobil™ Industrial Lubricants, we are committed to providing products and services that help deliver tangible performance and sustainability-related benefits – as well as material economic advantages – to Canadian industry and consumers. Our extensive range of high performance lubricants can help increase equipment operating efficiency and engine fuel economy. These lubricants can also contribute to reduced energy and resource use, lower emissions, and cost savings for industrial equipment. The Energy Efficiency Seal is the typographic representation for all Mobil Industrial Lubricants that meet the rigorous criteria for outstanding energy efficiency.
These criteria are determined on a case-by-case basis and are dependent on the product category and application. Statistically valid data must be available to substantiate the energy efficiency claim and demonstrate a statistically significant decrease in energy consumption or increase in efficiency when compared with commercially available products designed for the same application.
Below are the Mobil Industrial Lubricants products in which this technology is available: Mobil SHC™ 500 Mobil DTE 10 Excel™
Energy efficiency relates solely to the fluid performance when compared with Mobil DTE 10 Excel™ standard hydraulic fluids. The technology allows an increase in hydraulic pump efficiency of up to 6 percent compared with Mobil DTE 20 Series when tested in standard hydraulic applications. The energy efficiency claim for this product is based on test results conducted in accordance with applicable industry standards and protocols.
Mobil SHC Pegasus™ The energy efficiency of Mobil SHC Pegasus relates solely to the fluid performance when compared to standard Mobil SAE 40 natural gas engine oils. Mobil SHC Pegasus technology demonstrated an increase in fuel efficiency of up to 1.5 percent, compared to Mobil Pegasus 1005 and 805 series when tested in standard natural gas engine applications under controlled conditions. Efficiency improvements will vary based on operating conditions and applications. The energy efficiency claim for this product is based on test results on the use of the fluid conducted in accordance with applicable industry standards and protocols. Mobil SHC™ Gear
Energy efficiency relates solely to the fluid performance when compared with conventional reference (150-1000) oils of the same viscosity grade in gear applications. The technology used allows an increase in fuel efficiency of up to 3.6 percent compared with the reference oil when tested in a worm gearbox under controlled conditions. Efficiency improvements will vary based on operating conditions and applications.
Mobil SHC™ 600 Mobil SHC Cibus™
Energy efficiency relates solely to the fluid performance when compared to conventional (mineral) Mobil SHC Cibus™ reference oils of the same viscosity grade in circulating and gear applications. The technology allows an increase in fuel efficiency of up to 3.6 percent compared to the reference oil when tested in a worm gearbox under controlled conditions. Efficiency improvements will vary based on operating conditions and application. The above products provide energy efficiency benefits when compared with standard products of the same category and application, helping our customers to operate their equipment more efficiently.
9
Visit mobil.ca /pds for the most current product information
APPLICATION INDEX OF PRODUCTS
INDUSTRIAL LUBRICANTS Chain Oils.................................................................................................................... 18 Circulating Oils.......................................................................................................19-20 Compressor Oils..................................................................................................... 21-24 Cylinder Oils................................................................................................................25 Food Industry Lubricants........................................................................................26-27 Gas Engine Oils......................................................................................................28-32 Gear Oils – Enclosed Gears...................................................................................33-34 Gear Oils – Enclosed Gears Specialty...................................................................35-36 Gear Oils – Open Gears..............................................................................................36 Heat Transfer Fluids.....................................................................................................37 Hydraulic Fluids...................................................................................................... 37-40 Hydraulic Fluids – Less Flammable.............................................................................41 Metalworking Fluids................................................................................................42-43 Mist Oils.......................................................................................................................44 Other Industrial Oils................................................................................................45-46 Paper Machine Oils.....................................................................................................47 Pneumatic Tool Lubricant............................................................................................48 Quench Oils.................................................................................................................48 Refrigeration Oils.........................................................................................................49 Rust Preventive............................................................................................................50 Spindle Oils.................................................................................................................51 Transformer Oils..........................................................................................................51 Turbine Oils.............................................................................................................52-54 Way Oils......................................................................................................................55 COMMERCIAL VEHICLE LUBRICANTS Heavy Duty Diesel Engine Oils...............................................................................60-62 Heavy Duty Natural Gas Engine Oils..........................................................................62 Heavy Duty Power Transmission Fluids............................................................63, 66-67 Tractor Hydraulic Fluids...............................................................................................68 Railway........................................................................................................................68 Coolant/Antifreeze ......................................................................................................69
Visit mobil.ca /pds for the most current product information
10
APPLICATION INDEX OF PRODUCTS PASSENGER VEHICLE LUBRICANTS Passenger Vehicle Engine Oils..................................................................................74-76 Passenger Vehicle Drive Train Fluids.........................................................................77-78 Motorcycle Oils ............................................................................................................. 78 Passenger Vehicle Installer Greases............................................................................. 78 MARINE LUBRICANTS Crosshead Engine Oils.................................................................................................. 81 Trunk Piston Engine Oil................................................................................................. 82 Marine Hydraulic Oil...................................................................................................... 83 Marine Grease............................................................................................................... 83 AVIATION LUBRICANTS Grease...................................................................................................................... 85-86 Jet Oil............................................................................................................................ 86 GREASES Automotive..................................................................................................................... 91 Couplings....................................................................................................................... 92 Electric Motors............................................................................................................... 93 Environmentally Aware.................................................................................................. 93 Food Industry (NSF H-1)............................................................................................... 94 Gears – Enclosed, Semi-Fluid....................................................................................... 94 Gears – Open................................................................................................................ 95 High Temperature – Clay Thickened.............................................................................. 96 Marine........................................................................................................................... 96 Multi-Purpose............................................................................................................97-99 Off-Highway Heavy Duty Equipment and On-Highway Trucking...................................100 Paper Machines............................................................................................................ 101 Pneumatic Tools........................................................................................................... 101 Railway.........................................................................................................................102 Drilling..........................................................................................................................102 Specialty Synthetic.......................................................................................................103 Threads.................................................................................................................103-104 Wind Turbine.................................................................................................................104 Wire Ropes...................................................................................................................104
11
Visit mobil.ca /pds for the most current product information
MOBIL SHC GENERAL RECOMMENDATIONS
Productivity That’s Proven What truly sets Mobil SHC™ synthetic lubricants apart from its competitors is its track record. It represents Productivity That’s Proven – the underlying claim behind our brand. No other synthetic lubricant has the experience, the proof, and the reputation to match it. The full – and unmatched – suite of products that carry the Mobil SHC name have been tried, tested and proven in almost every type of equipment, under almost every condition. Mobil SHC General Recommendations: Circulating
Mobil SHC 600™ Series Mobil Glygoyle™ Numbered Series
Compressors
Mobil Rarus SHC™ 1020 Series (rotary screw and vane) Mobil Rarus™ 800 Series (reciprocating)
Food Industry (NSF H-1) Mobil SHC Polyrex™ Grease Series Gas Engine
Mobil SHC Pegasus™ 30 Mobil Pegasus™ 1
Gear
Mobil SHC 600™ Series Mobil SHC Gear™ Series Mobilgear SHC™ XMP Series (wind turbines)
Hydraulics
Mobil SHC™ 500 Series Mobil EAL Envirosyn™ H Series
Paper Machine
Mobil SHC™ PM Series Mobilith SHC™ PM Grease Series
Turbine
Mobil SHC™ 800 Series
Grease
Mobilith SHC™ Series (multi-purpose) Mobil SHC Polyrex™ Series (Food/NSF H-1, high temperature) Mobil SHC™ PF 462 (extreme high temperature) Mobil SHC™ Grease 460 WT (wind turbines) Mobiltemp SHC™ 32 (high speed) Mobil SHC™ Grease 100 EAL Series (environmentally aware) Mobilith SHC™ PM Series (paper machine)
Visit mobil.ca /pds for the most current product information
12
QUESTIONS? CALL OUR TECHNICAL SUPPORT CENTER AT
1 888 968-3776 mobilindustrial.com | mobildelvac.ca | mobil.ca
PAGE
Chain Oils Circulating Oils Compressor Oils Cylinder Oils
Millcot™ K.................................................................................18 Mobil™ Chainoil........................................................................18 Mobil™ Heavy Duty (HD) Chainoil............................................18
Food Industry Lubricants
Mobil™ Food and Beverage Industry Selector........................ 26 Mobil SHC Cibus™ Series....................................................... 27 Mobil DTE™ FM Series........................................................... 27
Mobil SHC™ 600 Series...........................................................19 Mobil Glygoyle™ Numbered Series..........................................19 Mobil Vacuoline™ 500 Series...................................................19 Mobil DTE™ Oil Named Series............................................... 20 Mobil Teresstic™-C.................................................................. 20 Mobil Teresstic™ V 150............................................................ 20 Mobil Rarus SHC™ 1020 Series............................................. 21 Mobil Rarus™ 800 Series........................................................ 21 Mobil Rarus™ 427................................................................... 21 Exxcolub™ SCF PG................................................................ 22 Exxcolub™ SCF PS................................................................. 22 Exxcolub™ SCF M2................................................................. 22 Exxcolub™ Application Chart.................................................. 23 Mobil™ Compressor Oils......................................................... 24 Mobil™ Compressor Oils 264 and 460.................................... 24 Mobil™ Compressor Oil N 100................................................ 24 Mobil Teresstic™ AC 32........................................................... 24 Mobil™ Cylinder Oils............................................................... 25 Mobil DTE™ Oil 205................................................................ 25
MARINE
PASSENGER
PRODUCT
COMMERCIAL
OIL APPLICATION
INDUSTRIAL
INDUSTRIAL PRODUCT LISTING BY APPLICATION
AVIATION
14
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL PRODUCT LISTING BY APPLICATION OIL APPLICATION
PRODUCT .
PAGE
Gas Engine Oils
Engine Oil Selection Chart...................................................... 28 Mobil SHC Pegasus™ 30........................................................ 29 Mobil Pegasus™ 1................................................................... 29 Mobil Pegasus™ GMA............................................................. 29 Mobil Pegasus™ 805............................................................... 29 Mobil Pegasus™ GLX.............................................................. 30 Mobil Pegasus™ 710............................................................... 30 Mobil Pegasus™ 610............................................................... 30 Mobil Pegasus™ 605............................................................... 31 Mobil Pegasus™ 801 Series.................................................... 31 Mobil Pegasus™ AGX.............................................................. 31 Engine Oil Selector.................................................................. 32
..........................................................................................
Gear Oils – Enclosed Gears
Mobil SHC Gear™ Series (ISO VG 150-1000)......................... 33 Mobil SHC Gear™ 1500, 3200, and 6800................................ 33 Mobilgear™ 600 XP Series...................................................... 34 SPARTAN™ EP-C.................................................................... 34
Gear Oils – Enclosed Gears Specialty Gear Oils – Open Gears Heat Transfer Fluids
Mobil SHC™ Gear OH Series.................................................. 35 Mobilgear SHC™ XMP Series................................................. 35 Mobil Glygoyle™ Series........................................................... 35 Mobil Iogear™ EP 100............................................................. 36 Mobil SHC Gear™ 46M........................................................... 36 Mobiltac™ 375 NC................................................................... 36 Mobil Geargard™ HVS............................................................. 36 Mobiltherm™ and Thermoil™.................................................. 37
15 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
PAGE
Mobil SHC™ 500 Series.......................................................... 37 Mobil DTE 10 Excel™ Series................................................... 37 Mobil DTE™ 20 Series............................................................. 38 Mobil Univis™ Ultra.................................................................. 38 Mobil Univis™ Extra................................................................. 38 Mobil Univis™ N-C Series........................................................ 39 Mobil Univis™ HVI 13.............................................................. 39 Mobil Univis™ BIO-C 40.......................................................... 39 Mobil Nuto™ H Series.............................................................. 40 Forum™ EP 46 and 68............................................................. 40
Hydraulic Fluids – Less Flammable
Mobil Nyvac™ FR 200D........................................................... 41 Mobil Pyrogard™ 53................................................................. 41
Metalworking Fluids
Mobilmet™ 420 Series............................................................. 42 Mobilmet™ 760 Series............................................................. 42 Mobilcut™ 100......................................................................... 42 Mobilcut™ 140......................................................................... 43 Mobilcut™ 350......................................................................... 43 Formesso™ Summer Grade.................................................... 43
Mist Oils
Mobilgear™ MS Series............................................................ 44
Click Here to return to PRODUCT APPLICATION INDEX
16
GREASES
Visit mobil.ca /pds for the most current product information
AVIATION
Other Industrial Oils Canthus™ 680......................................................................... 45 Faxam™................................................................................... 45 Mobil™ Sawguide Oils............................................................. 45 Mobil™ Synthetic Oven Lube 1090.......................................... 46 Mobil Synturion™ 6.................................................................. 46 Mobil™ System Cleaner........................................................... 46 Slurry Oil 62............................................................................. 46
MARINE
Hydraulic Fluids
PASSENGER
PRODUCT
COMMERCIAL
OIL APPLICATION
INDUSTRIAL
INDUSTRIAL PRODUCT LISTING BY APPLICATION
INDUSTRIAL PRODUCT LISTING BY APPLICATION OIL APPLICATION
PRODUCT
PAGE
Paper Machine Oils
Mobil SHC™ PM Series........................................................... 47 Mobil DTE™ PM Series........................................................... 47
Pneumatic Tool Oils Quench Oils
Mobil Arox™ EP Series............................................................ 48
Refrigeration Oils
Mobil Glygoyle™ 22................................................................. 49 Mobil Gargoyle™ Arctic Oils..................................................... 49 Mobil Gargoyle Arctic SHC™ 200 Series................................. 49 Mobil Zerice™ S Oils............................................................... 49
Rust Preventive
Mobilarma™ 245...................................................................... 50 Mobilarma™ 700 Series........................................................... 50 Mobil Vaprotec™ Light............................................................. 50
Spindle Oils
Mobil Velocite™ Oil Numbered Series..................................... 51
Mobil Fenso™ Series............................................................... 48
Transformer Oils Voltesso™................................................................................ 51
Turbine Oils
Mobil SHC™ 800 Series.......................................................... 52 Mobil DTE™ 932 GT................................................................ 52 Mobil DTE™ 800 Series........................................................... 52 Mobil DTE™ 724 Oil................................................................ 53 Mobil DTE™ 732 Oil................................................................ 53 Mobil DTE™ 700 Series........................................................... 53 Mobil Teresso™........................................................................ 54 Mobil Teresso™ GTC Series.................................................... 54
Way Oils
Mobil Vactra™ Oil Numbered Series........................................ 55 Mobil Vacuoline™ 1400 Series................................................. 55
17 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
CHAIN OILS Millcot™ K. Tacky, anti-spattering, general purpose oils, originally developed for textile machinery and well suited for a wide range of thin film applications in general manufacturing. Ideal for lumber industry applications, such as chains and hand oiled bearings
Millcot K 68 Millcot K 100 Millcot K 220
68 100 220
20 30 50
Product Mobil Chainoil Light Mobil Chainoil Heavy
Pour Point, °C, ASTM D97
Flash Point °C, ASTM D92
65.4 105 209
8.1 11.1 17.3
-24 -12 -3
196 202 238
for moderate temperatures (-10°C to 30°C), Mobil Chainoil Light for lower temperatures down to -30°C. Also recommended for industrial chain drive and plain bearing applications requiring a tacky anti-wear oil.
cSt at 40°C
Pour Point °C, ASTM D97
Flash Point °C, ASTM D92
40 150
-33 -20
180 190
anti-wear and extreme pressure additives help reduce wear to guide bars, chains and sprockets. A specialized inhibitor minimizes rust and corrosion. A tackiness additive helps reduce oil consumption due to throw-off. Also recommended for industrial chain drive and plain bearing applications requiring a tacky anti-wear oil.
Viscosity, ASTM D445 cSt at 40°C
Pour Point °C, ASTM D97
Flash Point °C, ASTM D92
220
-15
260
MARINE
Mobil Heavy Duty Chainoil
cSt at 100°C
Viscosity, ASTM D445
Mobil™ Heavy Duty (HD) Chainoil. This premium chainsaw lubricant helps extend the life of chains and guide bars on high speed chainsaws operating under severe conditions. Recommended for spring through fall operation across a temperature range of -5°C to 40°C. High viscosity base stocks enhanced with Product
cSt at 40°C
PASSENGER
Mobil™ Chainoil delivers excellent chain and bar lubrication in residential and industrial chain saw applications. A tacky stay-in-place film of oil lubricates, cleans and cools moving parts, helping to extend bar and chain life. Mobil Chainoil Heavy is recommended
Viscosity, ASTM D445
COMMERCIAL
Approximate Product ISO VG SAE Grade
in sawmills and lead screws on plywood veneer lathes. Millcot K oils are fortified with rust inhibitors and anti-wear additives and can be applied using most lubrication methods.
INDUSTRIAL
INDUSTRIAL LUBRICANTS
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
18
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS CIRCULATING OILS Mobil SHC™ 600 Series. These exceptional performance synthetic gear and bearing oils help increase productivity by delivering outstanding equipment protection, oil life and problem-free operation. The latest proprietary and patent pending Mobil SHC technology performs well beyond the capabilities of conventional oils in demanding applications across a wide range of temperatures. These products are resistant to
mechanical shear, even in heavily loaded gear and high shear bearing applications, so that there is virtually no loss of viscosity. Mobil SHC 600 Series lubricants have excellent low temperature properties, as well as improved air release performance in the lower viscosity grades. For information on energy efficiency, please see page 7.
Product ISO VG
Viscosity, ASTM D445 FZG scuffing test, cSt at 40°C
cSt at 100°C
V.I. ASTM D2270
Pour Point, °C, ASTM D5950
Flash Point, °C, ASTM D92
DIN 51534 (mod), A/16.6/90, Fail Stage
Mobil SHC 624 Mobil SHC 625 Mobil SHC 626 Mobil SHC 627 Mobil SHC 629 Mobil SHC 630 Mobil SHC 632 Mobil SHC 634 Mobil SHC 636 Mobil SHC 639
32 46 68 100 150 220 320 460 680 1000
6.3 8.5 11.6 15.3 21.1 28.5 38.5 50.7 69.0 98.8
148 161 165 162 166 169 172 174 181 184
-57 -54 -51 -45 -42 -42 -42 -39 -39 -33
236 225 225 235 220 220 225 228 225 222
11 12 12 12 13 13+ 13+ 13+ 13+ 13+
32 46 68 100 150 220 320 460 680 1000
Mobil Glygoyle™ Numbered Series oils are polyalkylene glycol-based (PAG) high performance lubricants that provide outstanding lubrication in extreme temperature gear, bearing and circulation system applications in conditions well beyond the capabilities of mineral oils. They are shear-stable
Viscosity, ASTM D445 Spec. Gravity
Product Mobil Glygoyle 22
cSt at 40°C
cSt at 100°C
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
kg/l at 20°C, ASTM D1298
177
25.1
-41
229
1.007
Mobil Vacuoline™ 500 Series are high performance heavy duty circulating oils specifically designed to meet the critical requirements of high speed No-Twist Rod Mills manufactured by Morgan Construction Company and Danieli. Their versatile performance makes them an excellent choice for circulation systems of primary and mini-mill bearings. These oils are formulated from Product ISO VG Mobil Vacuoline 525 Mobil Vacuoline 537
and have outstanding resistance to thermal degradation, oxidation and the formation of sludge and deposits. They incorporate a proprietary additive package designed to enhance EP/anti-wear protection, corrosion and rust protection and foam resistance without detracting from the intrinsic attributes of the PAG base oils.
– 320
high quality base stocks and a proprietary additive system to provide enhanced film strength, anti-wear and anti-scuff properties. They enjoy strong support from equipment builders, and their exceptional performance over many decades makes them the lubricant of choice of many mill operators, worldwide.
Viscosity, ASTM D445 Spec. Gravity cSt at 40°C
cSt at 100°C
V.I. ASTM D2270
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
kg/l at 15.6°C, ASTM D1298
89 309
10.7 24.4
99 96
-24 -12
264 288
0.88 0.89
19 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
CIRCULATING OILS to emulsification. They provide excellent protection against rust and corrosion, including resistance to salt water, and good anti-wear properties. These grades have excellent air release properties, enabling entrained air to separate, avoiding pump cavitation and erratic operation.
Viscosity, ASTM D445
Product ISO VG
cSt at 40°C
cSt at 100°C
V.I. ASTM D2270
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
Mobil DTE Oil Light Mobil DTE Oil Heavy Medium Mobil DTE Oil Heavy
31.0 65.1 95.1
5.5 8.7 10.9
102 95 92
-18 -15 -15
218 223 237
32 68 100
ring oiled steam turbine bearings. All viscosity grades are formulated with select high performance mineral oil base stocks and carefully chosen additives to provide long service life, outstanding oxidation control, excellent rust and corrosion protection, rapid air release and foam control.
Product ISO VG
Viscosity, ASTM D445 cSt at 40°C
cSt at 100°C
V.I. ASTM D2270
Pour Point, °C, ASTM D97
Mobil Teresstic-C 100 Mobil Teresstic-C 150 Mobil Teresstic-C 220 Mobil Teresstic-C 320
100.0 150.0 220.0 320.0
11.3 14.6 18.4 23.7
99 96 92 94
-15 -12 -6 -6
99 96 92 94
Product ISO VG Mobil Teresstic V 150
150
Flash Point, °C, ASTM D92 252 260 256 278
oxidation inhibitors help control corrosion and prolong oil life. A potent anti-wear additive helps protect gears and associated bearings.
MARINE
Mobil Teresstic™ V 150 circulating oil is recommended for older paper machines with specific performance requirements. A friction reducing additive is particularly effective in dryer section journal bearings. Rust and
PASSENGER
Mobil Teresstic™-C. These oils are formulated for long service life in circulating systems, hydraulic systems that do not require an anti-wear oil, heat transfer systems, light duty gear cases, friction clutches and other industrial units for which long, trouble-free service is required. They are also used to lubricate bath and
COMMERCIAL
Mobil DTE™ Oil Named Series are premium performance circulating oils for applications requiring long lubricant life, including steam and hydro turbine sets and other systems. These oils are formulated from highly refined base stocks and additives, which provide extremely high levels of chemical and thermal stability, rapid separation from water and high resistance
INDUSTRIAL
INDUSTRIAL LUBRICANTS
Viscosity, ASTM D445 cSt at 40°C
cSt at 100°C
Pour Point, °C, ASTM D97
150
14.6
-3
Flash Point, °C, ASTM D92 256
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
20
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS COMPRESSOR OILS Mobil Rarus SHC™ 1020 Series. These high performance oils are primarily intended for severe duty rotary screw and vane air compressors. They are particularly well suited where mineral oil based products are not meeting expectations, in applications subjected to high final compression temperatures or where extended oil drain intervals are desired. Designspecific wax-free synthetic fluids and high technology Viscosity, ASTM D445
Product ISO VG Mobil Rarus SHC 1024 Mobil Rarus SHC 1025 Mobil Rarus SHC 1026
additives are formulated for exceptional resistance to oxidation and thermal degradation. Their high viscosity index delivers effective lubrication at high temperatures. Mobil Rarus SHC 1020 Series oils help improve productivity and reduce maintenance costs by minimizing downstream deposits and delivering outstanding equipment protection and reliability.
32 46 68
cSt at 40°C
cSt at 100°C
V.I. ASTM D2270
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
31.5 44 66.6
5.7 7.2 10.1
127 131 136
-48 max -45 max -45 max
245 246 246
Mobil Rarus™ 800 Series is a line of high performance air compressor lubricants primarily intended for the lubrication of severe duty reciprocating air compressors. They are engineered to meet or exceed the stringent requirements of the major compressor manufacturers. They are formulated with synthetic ester base oils and a high technology additive system
that provides exceptional equipment protection and reliability. Mobil Rarus 800 Series oils provide excellent wear protection and outstanding resistance to oxidation and thermal degradation. Their unique formulation provides the ability to help reduce maintenance costs through minimizing equipment problems and downstream deposits and carryover.
Product ISO VG
Viscosity, ASTM D445 cSt at 40°C
cSt at 100°C
V.I. ASTM D2270
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
Mobil Rarus 824 Mobil Rarus 827 Mobil Rarus 829
29.5 107.5 158
5.5 10.12 13.2
127 66 70
-54 -36 -40
244 270 270
32 100 150
Mobil Rarus™ 427 is an air compressor lubricant designed to meet the requirements of the major compressor manufacturers. It is formulated with high quality mineral base oils and an additive system designed
to provide equipment protection and reliability. Mobil Rarus 427 provides good wear protection and air-oil separation, and limits valve deposits.
Product ISO VG
Viscosity, ASTM D445 cSt at 40°C
cSt at 100°C
V.I. ASTM D2270
Flash Point, °C, ASTM D92
Mobil Rarus 427
104.6
11.6
100
264
100
21 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
COMPRESSOR OILS
Exxcolub™ SCF PS. These premium quality synthetic blend gas compressor lubricants combine hydro treated mineral oil and polyalphaolefin (PAO) synthetic hydrocarbon oil. The proprietary multi-function silicone additive enhances lubricity and minimizes foaming.
A pour point depressant improves low temperature performance. A proprietary additive system reduces the effects of corrosive materials present in compressor streams, where lubricant is typically subjected to harsh chemicals, including hydrogen sulphide.
Exxcolub™ SCF M2. These premium hydrotreated paraffinic gas compressor lubricants are blended with a proprietary multi-function silicone additive to enhance lubricity and minimize foaming. A pour point depressant strengthens low temperature performance. Exxcolub SCF M2 oils are recommended for applica-
tions where lubricant is subjected to harsh chemical environments, including the presence of hydrogen sulphide. Also recommended for rotary screw, vane and reciprocating compressors in industrial applications requiring a higher viscosity lubricant.
Product ISO VG 100 150 190 100 150 100 150
Viscosity, ASTM D445 cSt at 40°C
cSt at 100°C
V.I. ASTM D2270
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
96 133 195 101 144 94 153
17.6 26 35.1 13.5 17.6 11.8 17.1
202 232 226 135 135 116 121
-48 max -42 max -43 max -33 max -33 max -37 max -30 max
218 257 304 277 288 248 271
MARINE
Exxcolub SCF PG 100 Exxcolub SCF PG 150 Exxcolub SCF PG 190 Exxcolub SCF PS 100 Exxcolub SCF PS 150 Exxcolub SCF M2 100 Exxcolub SCF M2 150
PASSENGER
long service life in high temperature operations. Inherently high viscosity indexes (>200) facilitate low temperature startup and help maintain acceptable viscosity over a wide temperature range. Polyalkylene Glycols are highly stable even at sustained high temperatures; this helps keep deposits to a minimum.
COMMERCIAL
Exxcolub™ SCF PG. These custom-blended Polyalkylene Glycol (PAG) synthetic lubricants deliver excellent performance in severe-service gas compressor applications, exceeding the capabilities of petroleum-base and many synthetic-base lubricants. Excellent oxidative and thermal stability helps assure
INDUSTRIAL
INDUSTRIAL LUBRICANTS
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
22
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS COMPRESSOR OILS
Lubricant
Benefits
Especially recommended for
Exxcolub SCF PG Polyalkylene glycol synthetic formula Grades: 100 & 150
• Approximately twice as resistant as mineral oils to gas dilution
• Sour gas and high CO2 applications
• Powerful corrosion inhibitors minimize risk of corrosion from hydrogen sulphide • Will allow a maximum of 20 percent (by weight) hydrocarbon dilution
Exxcolub SCF PS Synthetic blend Grades: 100 & 150
• Lighter than water, effective waterresistance and demulsibility • Silicone based corrosion inhibitors lessen the risk of corrosion from hydrogen sulphide
• Heavy hydrocarbons where severe dilution may occur • Cold weather conditions, especially for compressing gas of high specific gravity in cold weather
• Gas of low specific gravity under cold weather conditions and requiring a cost-effective alternative to a synthetic lubricant
• Very low vapour pressure minimizes lubricant consumption
Exxcolub SCF M2 Group ll mineral oil Grades: 100 & 150
• Control over carbon and varnish, with the potential for extended oil drain intervals
• Light hydrocarbons, sour gas and low water content where a modestly priced lubricant is required
• Silicone based corrosion inhibitors minimize risk of corrosion from hydrogen sulphide
23 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
COMPRESSOR OILS Mobil™ Compressor Oils provide outstanding lubrication in rotary and reciprocating air compressors. All viscosity grades deliver outstanding oxidation performance, wear protection, resistance to rust and corrosion, rapid water separation and foam control. Their thermal
Mobil Compressor Oil 68 Mobil Compressor Oil 122 Mobil Compressor Oil 220
68 – 220
Viscosity, ASTM D445 cSt at 40°C
cSt at 100°C
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
68 122 220
9.1 12.3 18.4
-21 -15 -12
240 230 245
Product ISO VG Mobil Compressor Oil 264 Mobil Compressor Oil 460
– 460
Viscosity, ASTM D445 cSt at 40°C
cSt at 100°C
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
280 485
23 35
-12 -12
280 280
Mobil Compressor Oil N 100
100
Viscosity, ASTM D445 cSt at 40°C
cSt at 100°C
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
98
9
-51
200
Teresstic AC 32
32
with silver plated components – requiring a mineral type oil that does not contain anti-wear additives. (For applications requiring anti-wear properties, Nuto H oils are recommended.)
AVIATION
Mobil Teresstic™ AC 32 is a compressor and circulating oil formulated primarily for applications in ammonia production and chemical plants. Mobil Teresstic AC 32 is well suited for hydraulic systems – such as those Product ISO VG
exposed to very high surface film temperatures, this oil produces miniscule amounts of soft, fluffy carbon deposits that are easily displaced. This product can also be used as a general purpose ISO 100 lubricant.
MARINE
Mobil™ Compressor Oil N 100. This premium ISO 100 viscosity mineral oil blend is particularly well suited as a once-through cylinder lubricant in large reciprocating compressors where heavy exhaust valve deposits have been observed with other oils. When Product ISO VG
with scrubber solution. They are ideally suited for initial break-in of compressor cylinders and packing. Both grades are formulated for outstanding cylinder and piston ring lubrication, oxidation resistance and chemical tolerance.
PASSENGER
Mobil™ Compressor Oils 264 and 460 are formulated with highly refined paraffin base oils and proprietary additive technology for compressor cylinders and packing. These high viscosity lubricants are recommended for applications where gas is sour, wet or contaminated
COMMERCIAL
Product ISO VG
stability and oxidation resistance help maintain clean compressors, enabling longer running periods between scheduled maintenance and oil changes. Outstanding anti-wear and corrosion protection help enhance equipment life, while reducing maintenance requirements.
INDUSTRIAL
INDUSTRIAL LUBRICANTS
Viscosity, ASTM D445 cSt at 40°C
cSt at 100°C
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
32
5.13
-40
204
Additional Compressor Oil Mobil SHC Cibus™ Series......................................... 27
Click Here to return to PRODUCT APPLICATION INDEX
24
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS CYLINDER OILS Mobil™ Cylinder Oils are high performance high viscosity oils designed for use in enclosed worm gears operating at moderate to high speeds and temperatures, and where heavy loads, slow speeds or high temperatures demand high viscosity oils. They are also intended for use in steam engines, natural gas compressors requiring a separate cylinder lubricant, Product ISO VG Mobil 600 W Cylinder Oil Mobil 600 W Super Cylinder Oil Mobil Extra Hecla Super Cylinder Oil
-- 460 680
Viscosity, ASTM D445 cSt at 40°C
cSt at 100°C
V.I. ASTM D2270
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
375 460 680
27.0 30.5 35.8
95 95 85
-9 -6 0
282 282 282
Mobil DTE™ Oil 205 is a lubricating oil formulated to provide excellent anti-wear and friction reducing properties for compressor cylinder lubrication, as well as protection against rust and corrosion. Mobil DTE Oil 205 is designed for wet-gas compression and Product Mobil DTE Oil 205
and down-hole applications. They are formulated from high quality base stocks that are resistant to oxidation and thermal degradation, and the build-up of harmful deposits caused by the high operating temperatures of steam cylinders. They protect against rust and corrosion, provide good film strength and excellent lubricity and they are resistant to water washout.
exhibits excellent resistance to washing by water and other entrained liquids. It resists oxidation and provides effective lubrication at low feed rates, helping to extend operating periods between valve-cleaning intervals.
Viscosity, ASTM D445 Spec. Gravity, cSt at cSt at Pour Point, Flash Point, kg/l at 15.6°C, 40°C 100°C °C, ASTM D97 °C, ASTM D92 ASTM D1298 220
19.5
25 Visit mobil.ca /pds for the most current product information
-9
282
0.90
Click Here to return to PRODUCT APPLICATION INDEX
FOOD INDUSTRY LUBRICANTS
Mobil™ Food and Beverage Industry
141500
Mobil SHC Cibus™ 46
51524-HLP 51506-VDL
141498
Mobil SHC Cibus™ 68
51524-HLP 51506-VDL
141499
Mobil SHC Cibus™ 150
51517-CLP
141502
Mobil SHC Cibus™ 220
51517-CLP
141503
Mobil SHC Cibus™ 320
51517-CLP
141505
Mobil SHC Cibus™ 460
51517-CLP
141501
Mobil Glygoyle™ 460
KP1K-20
136467
Mobilgrease™ FM Series (101)
KP1K-20
141881
Mobil SHC Polyrex™ Series KPFHC2P-20 (462)
MARINE
51524-HLP
PASSENGER
Mobil SHC Cibus™ 32
contamination from lubricating oils and greases. This comprehensive suite of high performance oils are NSF H1 registered, which is increasingly being requested by major food retailers and government agencies.
COMMERCIAL
The food and beverage processing industry faces unique challenges. Not only must you strive for maximum productivity, you must also guard against the possibility of food contamination, including
INDUSTRIAL
INDUSTRIAL LUBRICANTS
138558
AVIATION
Other Food Industry Lubricants • Mobil DTE™ FM (32, 46, 68): premium mineral oils • Mobil Synturion™ 6: synthetic mechanical seal fluid • Mobil Gargoyle Arctic SHC™ Series: synthetic refrigeration lubricants
Click Here to return to PRODUCT APPLICATION INDEX
26
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS FOOD INDUSTRY LUBRICANTS Mobil SHC Cibus™ Series lubricants are superb performance synthetic, compressor, hydraulic, gear and bearing oils designed to provide outstanding equipment protection, long oil life and problem-free Product ISO VG Mobil SHC Cibus 32 Mobil SHC Cibus 46 Mobil SHC Cibus 68 Mobil SHC Cibus 100 Mobil SHC Cibus 150 Mobil SHC Cibus 220 Mobil SHC Cibus 320 Mobil SHC Cibus 460
32 46 68 100 150 220 320 460
Viscosity, ASTM D445 Spec. Gravity cSt at 40°C
cSt at 100°C
V.I. ASTM D2270
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
kg/l at 15°C, ASTM D4052
30 43 72 102 162 222 311 458
5.8 7.7 11.4 14.6 20.7 24.5 32.7 43.6
140 148 151 148 150 139 147 148
14 >14 >14 >14 >14
products to provide outstanding performance under severe high and low temperature operating conditions. The nature of the synthetic base fluids also contributes to the products’ excellent low temperature performance. They have excellent protection against gear scuffing and resistance to shock loading. The synthetic base stocks have inherently low traction properties that result in low fluid friction in the load zone of nonconforming surfaces such as gears and rolling element bearings. Reduced fluid friction produces lower operating temperatures and improved gear efficiency.
Viscosity, ASTM D445 cSt at 40°C
cSt at 100°C
V.I. ASTM D2270
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
FZG test, ISO 14635-1 mod., Failure Stage
1500 3200 8200
113 183 365
165 165 180
-18 -9 -6
230 230 230
13+ 13+ 13+
33 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
GEAR OILS — ENCLOSED GEARS
Product Mobilgear 600 XP 68 Mobilgear 600 XP 100 Mobilgear 600 XP 150 Mobilgear 600 XP 220 Mobilgear 600 XP 320 Mobilgear 600 XP 460 Mobilgear 600 XP 680
trends toward smaller units with similar power throughput. This increase in power density places increased demands on lubricant. Mobilgear 600 XP Series oils meet the stress by providing extra protection for gears, bearings and seals.
Viscosity, ASTM D445 cSt at 40°C
cSt at 100°C
V.I. ASTM D2270
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
68 100 150 220 320 460 680
8.8 11.2 14.7 19.0 24.1 30.6 39.2
101 97 97 97 97 96 90
-27 -24 -24 -24 -24 -15 -9
230 230 230 240 240 240 285
12+ 12+ 12+ 12+ 12+ 12+ 12+
– 12+ 12+ 12+ 12+ 12+ 12+
bility and excellent protection from wear. The thermal stability of SPARTAN EP-C helps reduce sludge formation and keep internal surfaces clean. SPARTAN EP-C oils provide excellent protection against corrosion of steel and copper containing alloys. They also have excellent demulsibility, so that water separates rapidly from the oil, simplifying drain off from gear cases and system reservoirs.
PASSENGER
SPARTAN™ EP-C is the brand name for a family of premium quality industrial extreme pressure gear lubricants. They are formulated with high quality mineral oils and carefully selected high performance additives that work synergistically to provide excellent gear protection and long lubricant life. SPARTAN EP-C oils contain a sulphur/phosphorus Extreme Pressure additive system that provides high load-carrying capa-
FZG scuffing, FZG scuffing, Fail Stage A/8.3/90 Fail Stage A/16.6/90
COMMERCIAL
Mobilgear™ 600 XP Series high performance gear oils have excellent extreme pressure characteristics and load-carrying properties. They are intended for use in all types of enclosed gear drives with circulation or splash lubrication systems. These oils are designed to stay ahead of gearbox technology, including design
INDUSTRIAL
INDUSTRIAL LUBRICANTS
Kinematic Viscosity cSt at V.I. Pour Point, Flash Point, 100°C ASTM D2270 °C, ASTM D97 °C, ASTM D92
cSt at 40°C
Spartan All-Season Spartan 1000
150 1000
21.5 47.5
170 90
-36 -9
192 246
MARINE
Product
Additional Enclosed Gears Mobil SHC™ 600 Series............................................ 19
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
34
GREASES
Visit mobil.ca /pds for the most current product information
INDUSTRIAL LUBRICANTS GEAR OILS — ENCLOSED GEARS SPECIALTY Mobil SHC™ Gear OH Series. These exceptional performance synthetic gear oils are primarily designed to lubricate enclosed gears and plain and rolling element bearings in off-highway equipment subject to shock and heavy loading. They provide outstanding equipment protection, oil life and problem-free operation, promoting increased productivity. The synthetic base fluids deliver exceptional oxidation and thermal properties and excellent low temperature fluidity, contributing significantly to low temperature performance. Synthetic base stocks have inherently low traction properties that result in low fluid friction in the load zone of non-conforming Product ISO VG Mobil SHC Gear OH 320 Mobil SHC Gear OH 460 Mobil SHC Gear OH 680
320 460 680
Kinematic Viscosity, Viscosity, ASTM D445 FZG Gear Scuffing, cSt at 40°C
cSt at 100°C
V.I. ASTM D2270
Pour Point, °C, ASTM D5950
Flash Point, °C, ASTM D92
(A/8.3/90), ISO 14635-1 mod Failure Stage
320 460 680
40.1 54.9 76.1
178 186 193
-45 -42 -39
233 233 233
>13 >13 >13
Mobilgear SHC™ XMP Series lubricants are high performance synthetic wind turbine gear oils providing outstanding equipment protection and oil life, even under extreme conditions. Our synthetic base oil technology provides exceptional oxidation resistance and thermal properties, naturally high viscosity index, excellent low temperature fluidity and the absence of undesirable compounds often found in mineral oils. A high viscosity index and low traction coefficient Product ISO VG Mobilgear SHC XMP 320
320
surfaces such as gears and rolling element bearings. Reduced fluid friction produces lower operating temperatures and improved gear efficiency. A naturally high viscosity index and unique additive system combine to provide outstanding performance under severe high and low temperature operating conditions. Mobil SHC Gear OH Series oils deliver outstanding gear scuffing protection in heavily loaded gearboxes. Their available viscosity range: ISO VG 320 to 680. These are the products of choice for key OEMs and customers with demanding off-highway applications. For information on energy efficiency, please see page 7.
combine for a significant reduction in power consumption in many gear drives. An advanced proprietary additive system helps prevent conventional wear such as scuffing and provides high resistance to micropitting fatigue. Mobilgear SHC XMP oils deliver outstanding rust and corrosion protection and show no tendency to plug fine filters even when wet. Compatibility with ferrous and non-ferrous metals, even at elevated temperatures, is excellent.
Viscosity, ASTM D445 cSt at 40°C
cSt at 100°C
V.I. ASTM D2270
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
Spec. Gravity kg/l at 15.6°C, ASTM D4052
FZG Scuffing, DIN 51345 (mod) A/16.6/90, Fail Stage
335
38.3
164
-38
242
0.860
14+
Mobil Glygoyle™ Series lubricants are high performance gear, bearing and compressor oils delivering outstanding efficiency, long oil life, and equipment protection. These synthetic polyalkylene glycol (PAG)
oils were designed for operating conditions beyond the capabilities of other synthetic lubricants and mineral oils. Their low pour points ensure excellent lowtemperature fluidity.
Viscosity, ASTM D445
Product ISO VG
cSt at 40°C
cSt at 100°C
V.I. ASTM D2270
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
FZG Test, ISO. Fail Load Stage
Mobil Glygoyle 460
460.0
77.2
250
-33
265
12+
460
35 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
GEAR OILS — ENCLOSED GEARS SPECIALTY Mobil Iogear™ EP 100 is an extreme pressure gear oil specially designed for oil field pump jack gear drives and formulated to operate across a wide temperature
Viscosity, ASTM D445
SAE Product Grade 100
cSt at 40°C
cSt at 100°C
V.I. ASTM D2270
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
99.5
14.96
157
-40
170
Additional Enclosed Gears Specialty Mobil SHC Cibus™ Series......................................... 27
INDUSTRIAL LUBRICANTS
COMMERCIAL
Mobil IOGear EP 100
range for year-round performance. It is well suited for other gear applications requiring excellent low temperature performance.
INDUSTRIAL
INDUSTRIAL LUBRICANTS
GEAR OILS — OPEN GEARS high viscosity index and unique additive system combine to provide exceptional thermal/oxidative properties and outstanding performance under severe high and low temperature operating conditions, even with very slow moving gears. The additive formulation also provides excellent gear scuffing protection, antiwear performance and rust and corrosion inhibition.
Viscosity, ASTM D445
Product
cSt at 40°C
cSt at 100°C
V.I. ASTM D2270
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
Mobil SHC Gear 46M
46,000
1375
180
15
240
Product
consistency that is maintained throughout its service life. Mobiltac 375 NC adheres strongly to gear teeth and other machine elements to resist excessive throw-off, providing a wear resistant, viscous, continuous film that lubricates well under boundary conditions. Mobiltac 375 NC is available in spray cans. Spec. Gravity Flash Point, kg/l at 15.6°C, °C, ASTM D92 ASTM D1298
cSt at 40°C w/diluent
cSt at 100°C w/o diluent
5000
1260
Mobil Geargard™ HVS is an ultra-high viscosity lubricant primarily intended for heavily loaded, low and medium speed open gears that may operate in boundary lubrication conditions. The ultra-high viscosity synthetic fluid combines with extreme pressure additives
135
Smooth
Visit mobil.ca /pds for the most current product information
110
Viscosity, ASTM D445 cSt at 40°C without diluent
cSt at 100°C without diluent
44000
1350
Click Here to return to PRODUCT APPLICATION INDEX
36
GREASES
Black
0.96
to provide outstanding performance under severe conditions. Geargard HVS dispenses well in ambient temperatures as low as -10°C, while providing excellent gear protection at high operating temperatures.
Colour, Flash Point,°C Product Visual Structure with diluent Mobil Geargard HVS
0.924
AVIATION
Mobiltac 375 NC
Viscosity, ASTM D445
Spec. Gravity kg/l at 15.6°C, ASTM D4052
MARINE
Mobiltac™ 375 NC is an high performance non-leaded, diluent-type, heavy bodied open gear lubricant designed for a wide variety of open gear and mining applications. A non-chlorinated, volatile solvent ensures fluidity during application, even at low temperatures. Once applied, the diluent evaporates and the lubricant takes on a flexible, adhesive, high strength
PASSENGER
Mobil SHC Gear™ 46M is a high performance ultra high viscosity synthetic lubricant designed specifically for heavily loaded, low speed open gears where boundary lubrication conditions often prevail. Synthetic base stocks provide remarkable low temperature fluidity; they can be pumped over relatively long distances and applied with standard spray equipment. The naturally
INDUSTRIAL LUBRICANTS HEAT TRANSFER FLUIDS Mobiltherm™ and Thermoil™ heat transfer fluids offer many years of successful service in such industries as plastics, paint, rubber, paper mill calendars, board plants, roofing, textiles and refineries. Highly refined
Viscosity, ASTM D445
Product ISO VG Mobiltherm N 100 Thermoil 32 Thermoil 46 Thermoil 100
mineral base stocks and select additive technology combine for excellent thermal and oxidation stability. The volatility and flash points are optimized to reduce vapour pressure at elevated temperatures.
100 32 46 100
cSt at 40°C
cSt at 100°C
Pour Point, °C, ASTM D97
Flash Point, °C, ASTM D92
108 32 46 100
11.8 5.31 6.67 10.78
-18 2.0 >2.0
Dropping Point,°C Viscosity, ASTM D445 ASTM D2265 cSt at 40°C
Smooth Smooth, Semi-fluid Smooth, Semi-fluid Smooth, Semi-fluid
175 198 193 213
620 680 2000 4000
Click Here to return to PRODUCT APPLICATION INDEX
GREASES HIGH TEMPERATURE – CLAY THICKENED stability and a high dropping point, for outstanding high temperature protection. The wax-free synthetic base fluids with their high viscosity index also provide outstanding lubrication at low temperatures.
Product Mobiltemp SHC 32
Colour, Visual
NLGI Grade
Thickener Type
Dropping Point,°C ASTM D2265
Viscosity, ASTM D445 cSt at 40°C
Red
1.5
Clay
260+
32
mineral oil and specially formulated to provide low volatility and excellent resistance to oxidation at high temperatures, along with resistance to water washout and good anti-wear performance under heavy loads and low speeds. Mobiltemp 78 also contains molybdenum disulphide (Moly) for added anti-wear protection.
Product Mobiltemp 2 Mobiltemp 78
Colour, Visual
NLGI Grade
Thickener Type
Dropping Point,°C ASTM D2265
Viscosity, ASTM D445 cSt at 40°C
Amber Grey-black
2 1
Clay Clay
300 300
460 460
PASSENGER
Mobiltemp™ Series greases are high performance clay-thickened products designed for plain and antifriction bearings operating at low speed and high temperature or under cycling conditions from ambient to high temperatures. The clay thickener, unlike traditional soap thickeners, does not soften at high temperatures. These greases are based on a high quality, high viscosity
COMMERCIAL
Mobiltemp SHC™ 32 is a high performance anti-wear grease primarily intended for high temperature applications. Synthetic base oils deliver excellent resistance to thermal/oxidative degradation. The organo-clay nonsoap thickener provides high temperature structural
INDUSTRIAL
GREASES
Mobil SHC Aware™ Grease EP 2 is a high performance synthetic grease designed specifically for applications which are environmentally sensitive and meets the requirements of the U.S. Environmental Protection Agency (EPA) 2013 Vessel General Permit (VGP). This
leading product is readily biodegradable and virtually non-toxic grease and is formulated based on biodegradable saturated ester base oils and a lithium/calcium soap thickener. It does not emulsify and has excellent water wash and salt water corrosion resistance.
Product
Colour, Visual
NLGI Grade
Thickener Type
Dropping Point,°C ASTM D2265
Viscosity, ASTM D445 cSt at 40°C
Mobil SHC Aware Grease EP 2
Amber
2
Calcium/Lithium
>160
150
MARINE
MARINE
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
96
GREASES
Visit mobil.ca /pds for the most current product information
GREASES MULTI-PURPOSE Mobilith SHC™ Series greases are high performance products designed for a wide variety of applications at temperature extremes. They combine the unique features of synthetic base fluids with those of a high quality lithium complex thickener. The wax-free nature of synthetic fluids and the low coefficient of traction (compared with mineral oils) provide excellent low temperature pumpability and very low starting and running torque. These products offer the potential for
energy savings and can reduce operating temperatures in the load zone of spherical roller and ball bearings. The lithium complex thickener contributes excellent adhesion, structural stability and resistance to water. The greases have a high level of chemical stability and are formulated with special additive combinations to deliver excellent protection against wear, rust and corrosion, and to provide operating viscosity at high and low temperatures.
Viscosity, ASTM D445 Colour, NLGI Thickener Dropping Point,°C Product Visual Grade Type cSt at 40°C ASTM D2265 Mobilith SHC 007 Mobilith SHC 100 Mobilith SHC 220 Mobilith SHC 460 Mobilith SHC 1500
Red Red Red Red Red
00 2 2 1.5 1.5
Li-Complex Li-Complex Li-Complex Li-Complex Li-Complex
Mobilgrease XHP™ 220 Series greases are intended for a wide variety of applications and severe operating conditions. These extended service lithium complex greases were designed to outperform our conventional products through cutting edge, proprietary, lithium complex manufacturing technology. They deliver excellent high temperature performance with superb Product Mobilgrease XHP 221 Mobilgrease XHP 222 Mobilgrease XHP 222 Special
Mobilgrease XHP 461 Mobilgrease XHP 462 Mobilgrease XHP 462 Moly
– 265 265 265 265
Dark Blue Dark Blue Grey-Black
1 2 2
Li-Complex Li-Complex Li-Complex
– – 0.75
220 220 220
1 2 2
Dropping Point,°C ASTM D2265 280 280 280
chemical stability and offer excellent protection against rust and corrosion. These greases feature high dropping points and a maximum recommended operating temperature of 140°C. Mobilgrease XHP 462 Moly is fortified with 3% molybdenum disulphide to provide enhanced EP (extreme pressure) and AW (anti-wear) protection in heavily loaded and high sliding applications.
Viscosity, ASTM D445 Colour, NLGI Thickener Molybdenum Visual Grade Type Disulphide, Wt. % cSt at 40°C Dark Blue Dark Blue Grey
– 6 3 3 2.5
adhesion, structural stability and resistance to water contamination. These greases have a high level of chemical stability and offer excellent protection against rust and corrosion. They feature high dropping points and a maximum recommended operating temperature of 140°C. Base oil viscosity is ISO VG 220.
Viscosity, ASTM D445 Colour, NLGI Thickener Molybdenum Visual Grade Type Disulphide, Wt. % cSt at 40°C
Mobilgrease XHP™ 460 Series greases are intended for a wide variety of heavy duty applications and operating conditions. These extended service lithium complex greases were designed to outperform our conventional products through cutting edge, proprietary, lithium complex manufacturing technology. They deliver excellent high temperature performance with superb adhesion, structural stability and resistance to water contamination. These greases have a high level of Product
460 100 220 460 1500
Water Washout, ASTM D1264, 79°C, % Wt. Loss
Li-Complex Li-Complex Li-Complex
97 Visit mobil.ca /pds for the most current product information
– – 3
460 460 460
Dropping Point,°C ASTM D2265 280 280 280
Click Here to return to PRODUCT APPLICATION INDEX
GREASES MULTI-PURPOSE water saturated environments, providing rust protection between long re-lubrication intervals. The inherent EP properties exhibit great stability in the presence of water, providing a balance between wear protection and resistance to corrosion.
Water Washout, Colour, NLGI Thickener Viscosity, ASTM D445 Dropping Point,°C ASTM D1264, Product Visual Grade Type cSt at 40°C ASTM D2265 1 hr. at 79°C, % Mobil Centaur XHP 461 Mobil Centaur XHP 462
Amber Amber
1 2
Calcium Sulphonate Calcium Sulphonate
Mobilux™ EP Series lithium hydroxystearate greases are formulated to deliver extra protection against wear, rusting and water washout. They are particularly well
460 460
275 275
Water Spray Resistance, ASTM D4049, mass %
1.0 0.5
25 20
suited for applications in moist or wet conditions. Mobilux EP Series includes one general purpose grease and one special duty semi-fluid lubricant.
Colour, Visual
NLGI Grade
Thickener Type
Dropping Point,°C ASTM D2265
Viscosity, ASTM D445 cSt at 40°C
Mobilux EP 2 Mobilux EP 023
Brown Brown
2 000
Lithium Lithium
190 –
160 320
under load. Epic MQ is particularly recommended for centralized lubrication systems in open-pit mining, as well as severe-service, low temperature applications in forestry and construction. It is fortified with 5 percent molybdenum disulphide, as required by some equipment manufacturers. Epic greases have a long history of excellent performance in the toughest applications and under extreme temperature conditions.
Mobil Epic EP 102 Mobil Epic EP Moly Mobil Epic MQ
Red Grey-Black Grey-Black
1.5 1.5 0.5
Li-Complex Li-Complex Li-Complex
0 3 5
Dropping Point,°C ASTM D2265
Viscosity, ASTM D445 cSt at 40°C
260 260 230
130 130 60
MARINE
Molybdenum Colour, NLGI Thickener Disulphide Product Visual Grade Type Content, Wt. %
PASSENGER
Product
Mobil Epic™ Series are premium quality, semi-synthetic all-weather greases that deliver excellent lubrication and wear protection at temperatures as low as -50°C and as high as 150°C. They are recommended for multi-service applications in plain and anti-friction bearings, gears, slides and other situations where friction reduction and low wear are required. Epic EP Moly offers additional protection in applications involving heavy loads or slow reciprocating motion
COMMERCIAL
Mobil Centaur XHP™ 460 Series is a premium family of greases formulated with advanced calcium sulphonate thickener technology, which carries both inherent rust protection and extreme pressure (EP) properties. Relative to conventional soap-base thickeners (lithium, aluminum, calcium), calcium sulphonate excels in
INDUSTRIAL
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
98
GREASES
Visit mobil.ca /pds for the most current product information
GREASES MULTI-PURPOSE Mobil Unirex™ EP Series are extremely versatile long-life premium performance greases. Their unique formulation protects equipment over a very wide temperature range. Unirex greases are shear and oxidation stable, protect against rust and corrosion and resist softening at elevated temperatures. Unirex Lotemp EP is recommended for winter conditions that require low operating or dispensing limits. Unirex Lotemp Moly and Unirex EP 1 Moly offer performance Product Mobil Unirex EP 0 Mobil Unirex EP 1 Mobil Unirex EP 2 Mobil Unirex EP 0 Moly Mobil Unirex EP 1 Moly Mobil Unirex Lotemp EP Mobil Unirex Lotemp Moly
Colour, Visual
NLGI Grade
Thickener Type
Operating Temp. Range,°C
Dropping Point,°C ASTM D2265
Viscosity, ASTM D445 cSt at 40°C
Green Green Green Grey-Black Grey-Black Green Grey-Black
0.5 1 2 0.5 1 1.5 1.5
Li-Complex Li-Complex Li-Complex Li-Complex Li-Complex Li-Complex Li-Complex
-35 to 110 -30 to 160 -30 to 160 -35 to 110 -30 to 150 -55 to 110 -55 to 110
190 280 300 190 280 260 260
68 220 220 68 220 10 10
Mobil™ Argon EP greases are high quality, shear stable products suitable for use in both plain and anti-friction bearings lubricated by an automatic centralized dispensing system. Argon EP greases are widely used to lubricate mining equipment, bolt and nut formers, vane spindles of hydraulic turbines and a wide range of other machinery serviced by automatic dis Product Mobil Argon EP 0 Mobil Argon EP 1
Mobil Arcan 1
pensing equipment. They are useful over an operating temperature range of 0°C to 95°C. Argon EP 1 is an excellent choice for severe roller bearing service calling for an NLGI No.1 grease. Argon EP greases contain an extreme pressure additive, have a 21 kg Timken OK Load and are recommended where bearings are shock loaded or operating under heavy load conditions.
NLGI Grade
Thickener Type
Dropping Point,°C ASTM D2265
0 1
Calcium Calcium
135 135
Mobil™ Arcan 1 is a white filler-type grease widely used in bearings and mechanisms to combat severe water contamination. This grease has good adhesion to metal under wet conditions; it stays in place and maintains a lubricating film to protect metal surfaces from corrosion for extended intervals. As a result, Product
characteristics similar to Unirex Lotemp EP and Unirex EP 1 greases respectively; each adds the extreme pressure protection of molybdenum disulphide (Moly). Unirex greases meet the challenges of demanding applications in such industries as transportation, manufacturing, construction, mining, logging, cement, marine and paper-making, where grease must perform well in a multitude of severe applications.
Viscosity, ASTM D445 cSt at 40°C 175 175
Arcan 1 is well suited to such applications as printing machines, laundry and dry cleaning equipment and lubrication of office equipment. It is not recommended for wheel bearings, electric motor bearings or other high speed, grease packed anti-friction bearings. Operating temperature range is -5°C to 110°C.
Colour, Visual
NLGI Grade
Thickener Type
Dropping Point,°C ASTM D2265
White
1
Lithium
185
99 Visit mobil.ca /pds for the most current product information
Viscosity, ASTM D445 cSt at 40°C cSt at 100°C 100.0
10.0
Click Here to return to PRODUCT APPLICATION INDEX
GREASES OFF-HIGHWAY HEAVY DUTY EQUIPMENT AND ON-HIGHWAY TRUCKING Fortified with 3% molybdenum disulphide (Moly) to complement a robust extreme pressure (EP) additive system, these greases are particularly well suited to the demanding requirements of heavy duty truck chassis, construction and mining equipment, and heavily load industrial bearings.
Water Spray Molybdenum Water Washout, Resistance, Colour, NLGI Thickener Disulphide, Viscosity, ASTM D445 Dropping Point,°C ASTM D1264, ASTM D4049, Product Visual Grade Type Wt. % cSt at 40°C ASTM D2265 1 Hr at 79°C, % mass % Mobil Centaur Moly 1 Mobil Centaur Moly 2
Grey Grey
1 2
Calcium Sulphonate Calcium Sulphonate
3 3
288 280
Orange
2
Li-Complex
Colour, NLGI Thickener Product Visual Grade Type Mobilgrease XHP 100 Mine Mobilgrease XHP 320 Mine Mobilgrease XHP 321 Mine Mobilgrease XHP 322 Mine
Gray-Black Gray-Black Gray-Black Gray-Black
0 0 1 2
Li-Complex Li-Complex Li-Complex Li-Complex
320
Water Washout, ASTM D1264, 1 Hr at 79°C, %
260
6
harsh conditions. They deliver superior performance in bucket pins, pivot pins and heavily loaded chassis components. Mobilgrease XHP 100 Mine and 320 Mine are especially well suited for central lubrication systems in mining and other off-highway equipment requiring an NLGI 0 Grade grease.
Water Washout, Water Sprayoff, Molybdenum Viscosity, ASTM D445 Dropping Point,°C ASTM D1264, ASTM D4049, Disulphide, Wt. % cSt at 40°C ASTM D2265 79°C, % Loss % Loss 5 5 5 5
100 320 320 320
200 270 270 270
– – 10 2
– – 28 16
AVIATION
Additional Off-Highway Heavy Duty Equipment and On-Highway Trucking Greases Mobilgrease XHP™ 220 Series................................ 97 Mobilgrease XHP™ 460 Series................................ 97 Mobil Centaur XHP™ 460 Series............................. 98 Mobil Epic™ Series.................................................. 98 Mobil Unirex™ EP Series......................................... 99
Click Here to return to PRODUCT APPLICATION INDEX
100
GREASES
Visit mobil.ca /pds for the most current product information
MARINE
Mobilgrease XHP™ Mine lubricants are specifically designed for extra heavy duty off-highway and mining equipment. These greases have excellent extreme pressure and anti-wear properties, along with exceptional adhesion, very good resistance to water washout and spray-off, with extended service capabilities under
25 20
U-joints, and fifth wheels. It is also recommended for plain and anti-friction bearings in construction and mining vehicles operating in severe service and weather conditions. It is also recommended for heavily loaded industrial bearings. Recommended temperature range: -20°C to +175°C.
Colour, NLGI Thickener Viscosity, ASTM D445 Dropping Point,°C Product Visual Grade Type cSt at 40°C ASTM D2265 Mobil Delvac Xtreme Grease
1.0 1.0
PASSENGER
Mobil Delvac™ Xtreme Grease is an high performance extreme pressure lubricant. It exhibits excellent resistance to softening and provides good adhesion and cohesion, protection against wear and shock loads, and resistance to high temperature oxidation and rust. Mobil Delvac Xtreme Grease is recommended for use in heavy duty trucks, especially hinge and bucket pins,
320 320
COMMERCIAL
Mobil Centaur™ Moly Series are premium quality greases formulated with advanced calcium sulphonate thickener technology. Unlike conventional soap-base thickeners (lithium, aluminum, calcium), calcium sulphonate delivers outstanding resistance against the effects of water washout, water spray-off and corrosion.
INDUSTRIAL
GREASES PAPER MACHINES Mobilith SHC™ PM high performance greases are designed specifically for severe-service paper machine applications, including those in extreme temperature environments with exposure to different qualities of water. These lubricants combine the unique features of a synthetic base fluid with a high quality lithium complex thickener. The wax-free synthetic base fluid delivers excellent low temperature pumpability and
low starting and running torque when compared to non-synthetic oil products of the same viscosity; its high viscosity index ensures excellent film protection at high temperatures. The lithium complex thickener contributes excellent adhesion, structural stability and enhanced resistance to water. A special additive system resists rust, corrosion and oxidation and helps protect against wear.
Viscosity, ASTM D445 Dropping Point,°C Colour, NLGI Thickener Product Visual Grade Type cSt at 40°C ASTM D2265 Mobilith SHC PM 220 Mobilith SHC PM 460
Off-White Off-White
1.5 1.5
Li-Complex Li-Complex
Mobil Centaur XHP™ 221 is recommended for rolling element bearings in machinery operating at high temperatures where resistance to water washing and corrosion is important. Such applications include
220 460
275 275
Water Washout, ASTM D1264, 79°C, % Loss 2 3
wet-end paper machine bearings and heavily loaded industrial ball and roller bearings, including those in steel mills and mining.
Water Washout Colour, NLGI Thickener Viscosity, ASTM D445 Dropping Point,°C at 79°C ASTM D, Product Visual Grade Type cSt at 40°C ASTM D2265 1264, Wt. % Mobil Centaur XHP 221
Brown
1.5
Calcium Sulphonate Complex
220
318
1
Additional Paper Machine Greases Mobilgrease XHP™ 460 Series............................. 97 Mobil Unirex™ EP Series...................................... 99
GREASES PNEUMATIC TOOLS/AIR-LINE LUBRICATED Mobil Arox™ NM 000 is an extreme pressure, semi-fluid grease designed specifically to provide a mist-free, non-toxic environment for air-line lubricated pneumatic tools, including rock drills, jackhammers, drifters, wagon drills, chippers, tampers, riveters,
impact tools and pavement breakers. Low-odour, friction-and-wear-reducing additives also have emulsifying properties and help protect metal surfaces from corrosion and rust.
Product
Viscosity, ASTM D445 Colour, NLGI Thickener Visual Grade Type cSt at 40°C
Arox NM 000
Amber
000
101 Visit mobil.ca /pds for the most current product information
Calcium
140
Click Here to return to PRODUCT APPLICATION INDEX
GREASES RAILWAY
Product Arapen RB 320
withstand shear, i.e. retain consistency after prolonged working, as in the churning action of an anti-friction bearing. Arapen RB 320 maintains good seal performance, a significant requirement for shop-to-shop wheel service. It also resists heat, rust and structural change in the presence of water.
Colour, Visual
NLGI Grade
Thickener Type
Dropping Point,°C ASTM D2265
Viscosity, ASTM D445 cSt at 100°C
Light Amber
1.5
Calcium-Lithium
180
14.7
Galena™ Tramo 3735 is a sulphur-phosphorus extreme pressure traction-motor gear lubricant designed for all locomotives, including the newest,
high horsepower per axle units. It delivers excellent protection in severe temperatures, summer and winter, for effective all-season lubrication.
Viscosity, ASTM D445 Colour, Thickener Visual Type cSt at 100°C
Product
Black
Lithium
200.0
PASSENGER
Galena Tramo 3735
COMMERCIAL
Arapen™ RB 320 is a long-life grease developed for the roller bearings of railroad car journals where no provision is made for in-service relubrication. It has high oxidation stability and is highly resistant to chemical deterioration that might produce acids or deposits detrimental to bearing life. It has exceptional ability to
INDUSTRIAL
GREASES DRILLING
Product DDR Grease
At the same time, drill rods and joints may be washed by the sludge water used to force rock particulate upwards from the hole. DDR Grease is recommended for lubrication of diamond drill rods, on the surface or underground. It is normally applied by brush or hand and smeared over the drill rods where they are stacked.
Colour, Visual
NLGI Grade
Thickener Type
Dropping Point,°C ASTM D2265
Viscosity, ASTM D445 cSt at 40°C
Tan
3
Barium Complex
170
320.0
MARINE
DDR Grease is a very tacky and adhesive lubricating grease, formulated to stay in place in severe-service diamond drilling operations. The primary function of a drill rod grease is to reduce friction of the drill rod against the walls of the hole. This can be a considerable task when long lengths of pipe weave in the drill hole.
AVIATION
Click Here to return to PRODUCT APPLICATION INDEX
102
GREASES
Visit mobil.ca /pds for the most current product information
GREASES SPECIALTY SYNTHETIC Mobil SHC™ PF 462 grease is a long-life, severeservice lubricant for bearings, valves, seals and other applications requiring oxidation stability and lubrication performance at high temperatures. Formulated with perfluoropolyether thickened with polytetrafluoroethylene,
Viscosity, ASTM D445 cSt at cSt at Dropping Point,°C 40°C 100°C ASTM D2265
NLGI Product Grade Mobil SHC PF 462
2
440
42
Mobil Beacon 325
Water Washout, 79°C, ASTM D1264, % Loss
258
Mobil Beacon™ 325 is a high performance grease specifically formulated for precision equipment operating at moderate and low temperatures. Formulated with a synthetic base oil of extremely low viscosity and low volatility plus a lithium soap thickener, Beacon 325 delivers good mechanical stability, high resistance to Product
Mobil SHC PF 462 provides dependable performance up to 240˚ C and has excellent lubricity, corrosion resistance, thermal and oxidative stability and chemical inertness.
0.94
Water Spray-Off, ASTM D4049, % Weight Loss
5
water and extremely high oxidation stability. As the base oil viscosity is low and the viscosity index of the fluid is high, the grease has excellent low temperature properties, including low starting and running torque at very cold temperatures and good pumpability.
Colour, Visual
NLGI Grade
Thickener Type
Dropping Point,°C ASTM D2265
Viscosity, ASTM D445 cSt at 40°C
Tan
2
Lithium
180
12
GREASES THREADS Thredkote™ 706 is a simple soap grease containing graphite and metallic fillers such as lead, zinc and copper. It is designed for the lubrication of threads on casings, tubing and line joints in the oil drilling industry
and has been used successfully in Canada for many years. It is also used in the connection of high pressure steam lines and non-potable water lines.
Penetration, Viscosity, ASTM D445 Colour, NLGI mm/10 @ 25°C Product Visual Grade Dropping Point,°C cSt at 40°C % Graphite worked 60 strokes Thredkote 706
–
1
91
103 Visit mobil.ca /pds for the most current product information
–
18
330
Click Here to return to PRODUCT APPLICATION INDEX
GREASES THREADS
Product Z-50 Pipe Dope
Z-50 Pipe Dope is recommended for bolts, nuts and threaded fittings where tightness of the joint and ease of removal are desired. This product meets or exceeds the requirements of API recommended practice 7A1 for Rotary Shouldered Connection Thread Compounds. Its operating temperature range is -15°C to 150°C.
Colour, Visual
NLGI Grade
Dropping Point,°C ASTM D2265
Viscosity, ASTM D445 cSt at 40°C
Grey-Black
1
91
12
GREASES
Mobil SHC™ Grease 460 WT is a high performance product especially suited to meet or exceed the demanding requirements of wind turbine applications at temperature extremes. The wax-free nature of the synthetic base fluids and their low coefficient of traction provide excellent low temperature pumpability
and very low starting and running torque. The lithium complex thickener contributes excellent adhesion, structural stability and resistance to water. The grease has a high level of chemical stability. Special additive combinations provide excellent protection against wear, rust and corrosion at high and low temperatures.
Water Washout, Viscosity, ASTM D445 Dropping Point,°C Colour, NLGI Thickener ASTM D1264, Product Visual Grade Type cSt at 40°C ASTM D2265 Loss at 79°C, % wt 1.5
Li-Complex
460
255
10
MARINE
Red
PASSENGER
WIND TURBINES
Mobil SHC Grease 460 WT
COMMERCIAL
Z-50 Pipe Dope is an anti-seize compound recommended for a wide variety of applications. In oil field operations, it is used on the threads of new drill pipe and can also be applied as a sealing compound on the threads of semi-permanent joints, as when casing is set. In automotive and industrial applications,
INDUSTRIAL
GREASES WIRE ROPES
Product Wire Rope Dressing
Colour, Visual Structure Black
Smooth
Thickener Type
Dropping Point,°C ASTM D2265
Lithium
205
Viscosity, ASTM D445 cSt at 40°C
320
Click Here to return to PRODUCT APPLICATION INDEX
104
GREASES
Visit mobil.ca /pds for the most current product information
is formulated with non-asphaltic mineral base stocks, which minimize peeling, cracking and flaking off in cold weather. It contains molybdenum disulphide and solid graphite lubricant as well as additives to resist water and protect wire rope from rust and corrosion.
AVIATION
Wire Rope Dressing is an all-season, multi-purpose lubricant for hoist drum wire ropes in underground mining, dragline or electro-mechanical shovel operations. At ambient temperatures between -40°C and 50°C, wire ropes are protected by a tenacious film that adheres firmly to the rope. Wire Rope Dressing
APPENDICES Temperature Conversion Table Locate in the centre column of the three columns the temperature in °C or °F to be converted. For given Celsius temperatures, read Fahrenheit equivalent in the left-hand column. For given Fahrenheit temperatures, read the Celsius equivalent in the right-hand column. Examples: a. Given -30°C; convert to Fahrenheit. Locate -30 in the centre column; read -22.0°F in the left-hand column. b. Given -30°F; convert to Celsius. Locate -30 in the centre column; read -34.4°C in the right-hand column. For temperatures not shown, interpolate from the values listed or use the following equations: °C = (°F - 32) x 5 °F = °C x 9 + 32 9 5
To °F
From °C or °F
To °C
To °F
From °C or °F
To °C
To °F
-148.0 -130.0 -112.0 -94.0 -76.0 -58.0 -54.4 -50.8 -47.2 -43.6 -40.0 -36.4 -32.8 -29.2 -25.6 -22.0 -18.4 -14.8 -11.2 -7.6 -4.0 -0.4 +3.2 +6.8 +10.4 +14.0 +15.8 +17.6 +19.4 +21.2
-100 -90 -80 -70 -60 -50 -48 -46 -44 -42 -40 -38 -36 -34 -32 -30 -28 -26 -24 -22 -20 -18 -16 -14 -12 -10 -9 -8 -7 -6
-73.3 -67.8 -62.2 -56.7 -51.1 -45.6 -44.4 -43.3 -42.2 -41.1 -40.0 -38.9 -37.8 -36.7 -35.6 -34.4 -33.3 -32.2 -31.1 -30.0 -28.9 -27.8 -26.7 -25.6 -24.4 -23.3 -22.8 -22.2 -21.7 -21.1
+23.0 +24.8 +26.6 +28.4 +30.2 +32.0 +33.3 +35.6 +37.4 +39.2 +41.0 +42.8 +44.6 +46.4 +48.2 +50.0 +51.8 +53.6 +55.4 +57.2 +59.0 +60.8 +62.6 +64.4 +66.2 +68.0 +69.8 +71.6 +73.4 +75.2
-5 -4 -3 -2 -1 0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +10 +11 +12 +13 +14 +15 +16 +17 +18 +19 +20 +21 +22 +23 +24
-20.6 -20.0 -19.4 -18.9 -18.3 -17.8 -17.2 -16.7 -16.1 -15.6 -15.0 -14.4 -13.9 -13.3 -12.8 -12.2 -11.7 -11.1 -10.6 -10.0 -9.4 -8.9 -8.3 -7.8 -7.2 -6.7 -6.1 -5.6 -5.0 -4.4
+77.0 +78.8 +80.6 +82.4 +84.2 +86.0 +87.8 +89.6 +91.4 +93.2 +95.0 +96.8 +98.6 +100.4 +102.2 +104.0 +106.8 +107.6 +109.4 +111.2 +113.0 +114.8 +116.6 +118.4 +120.2 +122.0 +123.8 +125.6 +127.4 +129.2
105 Visit mobil.ca /pds for the most current product information
From °C or °F +25 +26 +27 +28 +29 +30 +31 +32 +33 +34 +35 +36 +37 +38 +39 +40 +41 +42 +43 +44 +45 +46 +47 +48 +49 +50 +51 +52 +53 +54
To °C -3.9 -3.3 -2.8 -2.2 -1.7 -1.1 -0.6 0.0 +0.6 +1.1 +1.7 +2.2 +2.8 +3.3 +3.9 +4.4 +5.0 +5.6 +6.1 +6.7 +7.2 +7.8 +8.3 +8.9 +9.4 +10.1 +10.6 +11.1 +11.7 +12.2
Click Here to return to PRODUCT APPLICATION INDEX
APPENDICES
Temperature Conversion Table
+131.0 +132.8 +134.6 +136.4 +138.2 +140.0 +141.8 +143.6 +145.4 +147.2 +149.0 +150.8 +152.6 +154.4 +156.2 +158.0 +159.8 +161.6 +163.4 +165.2 +167.0 +168.8 +170.6 +172.4 +174.2 +176.0 +177.8 +179.6 +181.4 +183.2 +185.0 +186.8 +188.6 +190.4 +192.2 +194.0 +195.8 +197.6 +199.4 +201.2 +203.0 +204.8 +206.6 +208.4 +210.2 +212.0 +213.8 +215.6 +217.4 +219.2
+55 +56 +57 +58 +59 +60 +61 +62 +63 +64 +65 +66 +67 +68 +69 +70 +71 +72 +73 +74 +75 +76 +77 +78 +79 +80 +81 +82 +83 +84 +85 +86 +87 +88 +89 +90 +91 +92 +93 +94 +95 +96 +97 +98 +99 +100 +101 +102 +103 +104
To °C +12.8 +13.3 +13.9 +14.4 +15.0 +15.6 +16.1 +16.7 +17.2 +17.8 +18.3 +18.9 +19.4 +20.0 +20.6 +21.1 +21.7 +22.2 +22.8 +23.3 +23.9 +24.4 +25.0 +25.6 +26.1 +26.7 +27.2 +27.8 +28.3 +28.9 +29.4 +30.0 +30.6 +31.1 +31.7 +32.2 +32.8 +33.3 +33.9 +34.4 +35.0 +35.6 +36.1 +36.7 +37.2 +37.8 +38.3 +38.9 +39.4 +40.0
To °F
From °C or °F
+221.0 +222.8 +224.6 +226.4 +228.2 +230.0 +231.8 +233.6 +235.4 +237.2 +239.0 +240.8 +242.6 +244.4 +246.2 +248.0 +251.6 +255.2 +258.8 +262.4 +266.0 +269.6 +273.2 +276.8 +280.4 +284.0 +287.6 +291.2 +294.8 +298.4 +302.0 +305.6 +309.2 +312.8 +316.4 +320.0 +323.6 +327.2 +330.8 +334.4 +338.0 +341.6 +345.2 +348.8 +352.4 +356.0 +359.6 +363.2 +366.8 +370.4
Visit mobil.ca /pds for the most current product information
+105 +106 +107 +108 +109 +110 +111 +112 +113 +114 +115 +116 +117 +118 +119 +120 +122 +124 +126 +128 +130 +132 +134 +136 +138 +140 +142 +144 +146 +148 +150 +152 +154 +156 +158 +160 +162 +164 +166 +168 +170 +172 +174 +176 +178 +180 +182 +184 +186 +188
To °C +40.6 +41.1 +41.7 +42.2 +42.8 +43.3 +43.9 +44.4 +45.0 +45.6 +46.1 +46.7 +47.2 +47.8 +48.3 +48.9 +50.0 +51.1 +52.2 +53.3 +54.4 +55.6 +56.7 +57.8 +58.9 +60.0 +61.1 +62.2 +63.3 +64.4 +65.6 +66.7 +67.8 +68.9 +70.0 +71.1 +72.2 +73.3 +74.4 +75.6 +76.7 +77.8 +78.9 +80.0 +81.1 +82.2 +83.3 +84.4 +85.6 +86.7
To °F +374.0 +377.6 +381.2 +384.8 +388.4 +392.0 +395.6 +399.2 +402.8 +406.4 +410.0 +413.6 +417.2 +420.8 +424.4 +428.0 +437.0 +446.0 +455.0 +464.0 +473.0 +482.0 +491.0 +500.0 +509.0 +518.0 +527.0 +536.0 +545.0 +554.0 +563.0 +572.0 +590.0 +608.0 +626.0 +644.0 +662.0 +680.0 +698.0 +716.0 +734.0 +752.0 +932.0 +1112.0 +1292.0 +1472.0 +1652.0 +1832.0 +2012.0 +2192.0
From °C or °F
To °C
+190 +192 +194 +196 +198 +200 +202 +204 +206 +208 +210 +212 +214 +216 +218 +220 +225 +230 +235 +240 +245 +250 +255 +260 +265 +270 +275 +280 +285 +290 +295 +300 +310 +320 +330 +340 +350 +360 +370 +380 +390 +400 +500 +600 +700 +800 +900 +1000 +1100 +1200
+87.8 +88.9 +90.0 +91.1 +92.2 +93.3 +94.4 +95.6 +96.7 +97.8 +98.9 +100.0 +101.1 +102.2 +103.3 +104.4 +107.2 +110.0 +112.8 +115.6 +118.3 +121.1 +123.9 +126.7 +129.4 +132.2 +135.0 +137.8 +140.6 +143.3 +146.1 +148.9 +154.4 +160.0 +165.6 +171.1 +176.7 +182.2 +187.8 +193.3 +198.9 +204.4 +260.0 +315.6 +371.1 +427.0 +482.0 +538.0 +593.0 +649.0
Click Here to return to PRODUCT APPLICATION INDEX
106
ALPHABETICAL INDEX OF PRODUCTS
From °C or °F
APPENDICIES
To °F
(continued)
APPENDICES Viscosity Conversion Table Kinematic Redwood Kinematic Redwood Kinematic Redwood cSt 40 C SUS Engler No. 1 Sec. cSt 40 C SUS Engler No. 1 Sec. cSt 40 C SUS Engler No. 1 Sec.
2 32.6 1.14 30.8 3 36.0 1.22 33.2 4 39.1 1.31 35.8 5 42.5 1.40 38.4 6 45.7 1.48 41.0 7 49.0 1.56 43.7 8 52.0 1.65 46.5 9 55.7 1.74 49.2 10 59.0 1.83 52.1 11 62.5 1.92 55.2 12 66.2 2.02 58.4 13 70.0 2.12 61.6 15 77.5 2.32 68.2 17 85.5 2.55 75.2 19 94 2.77 82.8 21 100 3.00 90.4 23 111 3.23 98 25 120 3.46 106 28 133 3.83 117 30 142 4.09 125 33 155 4.46 137 35 164 4.71 145 38 178 5.10 157 40 187 5.35 166 43 200 5.75 178
46 214 6.15 190 50 233 6.65 207 55 256 7.25 228 60 279 7.9 248 65 302 8.6 268 70 325 9.25 286 75 349 9.85 307 80 372 10.5 329 85 395 11.2 349 90 418 11.8 370 95 442 12.5 390 100 465 13.2 410 110 511 14.5 450 120 558 15.8 490 130 605 17.1 530 140 649 18.4 570 150 695 19.7 620 160 742 21.0 660 170 788 22.5 700 180 834 24.0 740 190 881 25.0 780 200 927 26.0 820 210 973 28.0 860 220 1020 29.0 900 230 1066 30.0 940
240 1112 32 990 250 1159 33 1030 260 1205 34 1070 270 1251 36 1110 280 1297 37 1150 290 1344 38 1190 300 1390 40 1230 315 1460 41 1300 330 1529 43 1350 350 1622 46 1440 370 1715 49 1520 390 1807 51 1600 410 1900 54 1690 430 1990 57 1770 450 2090 59 1850 470 2180 62 1930 490 2270 64 2010 500 2320 66 2050 550 2540 72 2260 600 2780 79 2460 650 3010 86 2670 700 3240 92 2880 750 3470 99 3080 800 3700 105 3280
Dynamic Viscosity to Kinematic Viscosity Calculation To convert from dynamic viscosity units, centipoise (cP), to kinematic viscosity units, centistokes (cSt), use the following equation: cSt = cP Density (kg/L) Note: Viscosity and density must be measured at the same temperature. If viscosity is known at two or more different temperatures, viscosity at other temperatures can be estimated using standard charts or equations. Charts are available from your Imperial sales representative or technical services department.
107 Visit mobil.ca /pds for the most current product information
Click Here to return to PRODUCT APPLICATION INDEX
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150 50,000
Click Here to return to PRODUCT APPLICATION INDEX
TEMPERATURE, DEGREES CELSIUS /TEMPÉRATURE, DEGRÉS CELSIUS
3.0 150
3.0 140
4.0
4.0
130
5.0
5.0
120
6.0
6.0
110
7.0
7.0
100
8.0
8.0
90
10 9.0
10 9.0
80
15
15
70
20
20
60
30
30
50
40
40
40
50
50
30
75
75
20
100
100
10
150
150
0
200
200
-10
300
300
-20
500 400
500 400
-40
1,000
3,000
5,000 2,000
-30
VISCOSITY – TEMPERATURE CHART RELATION VISCOSITÉ – TEMPÉRATURE
1,000
ALPHABETICAL INDEX OF PRODUCTS
Visit mobil.ca /pds for the most current product information
APPENDICIES
2,000
3,000
5,000
10,000
-10
20,000
-20
10,000
-30
20,000
-40 50,000
APPENDICES
108
KINEMATIC VISCOSITY, CENTISTOKES /VISCOSITÉ CINÉMATIQUE, CENTISTOKES
APPENDICES SAE Viscosity Grades for Engine Oils SAE Viscosity Grade
Low-temperature Cranking Viscosity1 cP at °C, Max.
0W 5W 10W 15W 20W 25W 20 30 40 40 50 60
6,200 @ -35 6,600 @ -30 7,000 @ -25 7,000 @ -20 9,500 @ -15 13,000 @ -10 — — — — — —
Low-temperature Low Shear Rate Low Shear Rate Pumping Viscosity Kinematic Kinematic High Shear Rate 2 3 with no yield-stress Viscosity Viscosity3 Viscosity4 cP at °C, Max. cSt at 100°C, Min. cSt at 100°C, Max. cP at 150°C, Min. 60,000 @ -40 60,000 @ -35 60,000 @ -30 60,000 @ -25 60,000 @ -20 60,000 @ -15 — — — — — —
3.8 3.8 4.1 5.6 5.6 9.3 5.6 9.3 12.5 12.5 16.3 21.9
— — — — — —
