BOQ (CIVIL, INTERIOR & ELECTRICAL WORKS) FURNISHING WORK FOR BANK OF INDIA AT : PRATAP NAGAR ,JODHPUR ( No work counted in ATM room except data & load lines)

S.No

Description

Amount.(Rs.)

1

TOTAL FOR INTERIOR WORKS

Rs.

2

TOTAL FOR ELECTRICAL WORKS

Rs.

3

TOTAL FOR CIVIL & ALLIED WORKS

Rs.

SUB TOTAL ( 1+2+3)

Rs.

Unconditional Discounts (in%) if any:

GRAND TOTAL

Rs.

Page 1 of 10

Interior Work

BOQ FOR INTERIOR WORKS S.No.

Description

Unit

Qty

1

Deleted

2

FAÇADE OF ENTRANCE DOOR (ACP- Exterior Grade ) Sq Ft. Providing and fixing in position Aluminium composite panel Boxing with PVDF coating & LDPE core laminated Eurobond / Altobond/ Alukbond Exterior Grade 4 mm thick with composite of (0.5mm-3mm-0.5mm) including fabrication for the same with aluminium sections, required hardware, silicon sealent (Dow Corning 789) masking tape, necessary scaffolding etc. as detailed in drawing complete in all respect.

500

3

FALSE CEILING (Armstrong) Sq Ft. Providing & fixing in position false ceiling in Armstrong 600 x 600 mm x 15/16 mm Dune Supreme RH 99 Prima tile with Tegular edge framework as specified by Armstrong Co. with suspenders wherever required. Making necessary framework for A.C. ducting, if any, and necessary cutouts for diffusers and light fittings, taping and finishing to proper line & level, including making grooves and trap doors for A.C unit in 18mm thick M.R. Grade Plywood with Stainless Steel hinges and locks with moulding 1"X1" for edges including finisheing with white Plastic paint etc. complete in all respects Note:- Only the plan area will be measured for payment ( No extra payment will be made for cutouts, grooves, mouldings etc.)

475

4

FALSE CEILING (India Gypsum) Providing & fixing in position false ceiling in Gypboard 12mm thick for horizontals & verticals fixed over G.I. framework as specified by India Gypsm Co. Ltd. including trap doors for A.C unit in 18mm thick M.R. Grade Plywood with Stainless Steel hinges & locks with moulding 1” X1” for edges including finishing with White Plastic Emulsion Paint etc. complete in all respects. (Note:- Only the plan area will be measured for payment. No extra payment will be made for cutouts, grooves, drops, mouldings etc. )

5

Deleted

Sq Ft.

Rate

Amount

1050

Page 2 of 10

Interior Work

6

ENTRANCE DOOR Providing and fixing Entrance Door (glazed) as per drawing in Silver Anodised aluminium door section (Jindal make) in top and bottom, glazed with 12 mm thick glass of approved make with etching and frosting. Item to include floor springs, lock, handles, all necessary hardwares of Stainless Steel finish as approved by the Project Consultant/ Bank complete in all respects.

Sq Ft.

45

7

FRONT OFFICE COUNTER Providing and fixing in position Front Office Counter 2’-6” wide as per drawing comprising of the following complete in all respects. Working top made with 25mm thick plywood finished with 1mm thick laminate. Outside edge of the working top shall be provided with 1¼”X1” Teak Wood moulding finished with melamine polish. Inside edge will be provided with ½ “x1” T.W. beading patti with melamine polish Vertical facia (Apron) made with 18mm thick plywood finished with 1mm thick laminate with 1mm thick groove at the joint of laminates of two different shades. Vertical drop (horizontal band) shall be provided on the facia below the working top made with 18mm thick plywood finished with 1mm thick laminate with provision for concealed light, 1 mm thick groove shall be provided at the joint of two different shades of laminate. Glazed partition above working top to be provided with 12mm thick clear glass cut to the standard shape fixed to partition as per fixing details and to boxing with concealed S. S. finished ‘D’ brackets as shown in the drawing. The exposed edges of the glass shall be finished in mirror polish. 3’-10” high Boxing (10”x10”) made with 18 mm thick plywood finished with 1 mm thick laminate including providing and fixing 6 mm thick square frosted glass at a height 3’-2” above finished floor level. 1’-9” high Boxing (5”x5”) made with 12 mm thick plywood finished with 1 mm thick laminate. finished with white enamel paint. Vertical supports made with 18 mm thick plywood finished with white enamel paint. Telescopic CPU Stand/ ready made Keyboard tray shall be provided of approved model and make. Footrest made with T.W. member of size 4”X1 ½ “ finished with french polish Drawer units as per drawing shall be provided with multipurpose Godrej locks in Each drawer. Facia of drawer unit shall be finished with 1mm thick laminate and all other sides shall be finished with white enamel paint. The drawers will be provided with handles (Stainless Steel finish) and channels as per approval of the Project Architect/ Bank Boxing as per drawing made with 12mm thick plywood finished with Synthetic enamel paint shall be provided below the table top for electrical conduiting and at the bottom for the LAN cabling/Telephone wire conduiting. The item to include all necessary hardware and fittings in Stainless Steel finish, lipping to all edges and making provision only for electrical fitting behind the front. Vertical drop and also in the 10”x10” boxing as shown in the drawing. Necessary tw beadings with melamine polish for fixing the glass are to be provided.

R.Ft

8.5

R. Ft.

16

a.

b.

c.

d.

e.

f.

g. h. i. j.

k.

8

CASH COUNTER Providing and fixing in position Cash Counter 2’-9” wide as per drawing comprising of the following a. Working top made with 25mm thick plywood finished with 1mm thick laminate. Outside edge of the working top shall be provided with 1¼”X1” Teak Wood moulding finished with melamine polish. Inside edge will be provided with ½ “x1” T.W. beading patti with melamine polish b. Vertical facia (Apron) made with 18mm thick plywood finished with 1mm thick laminate with 1mm thick groove at the joint of laminates of two different shades

Page 3 of 10

Interior Work

c.

d.

e.

f.

g.

h.

i. j. k. l.

m.

9

Vertical drop (horizontal band) shall be provided on the facia below the working top made with 18mm thick plywood finished with 1mm thick laminate with provision for concealed light, 1 mm thick groove shall be provided at the joint of two different shade of laminate. Glazed partition of 1’-4” height above working top provided with 12mm thick toughened and frosted glass besides non-transparent film from inside fixed to partition as per fixing details and to boxing with concealed S. S. finished ‘D’ brackets as shown the drawing. The exposed edges of the glass shall be finished in mirror polish. Transaction top shall be provided with 12mm thick toughened glass (partly glazed partly frosted) fixed horizontally with concealed Stainless Steel D bracket. Both exposed edges (inside and outside) shall be moulded and finished in mirror polish. Glazed partition having height ( as per drg.) above the transaction top (in facia) shall be provided with 12 mm thick glass (clear) with cut out of 8”x 4” as per drawing. The edges of cut out and the top edge of glass are to be mirror polished and to be fixed to partition as per fixing details and to boxing with concealed S. S. finished ‘D’ brackets as shown in the drawing. Glazed partition provided with 12mm thick glass (Clear) above the slit to be fixed to partition as per fixing details and to boxing with concealed S. S. finished ‘D’ brackets as shown in the drawing. . The exposed edges shall be finished in mirror polish. 7’-7” high Boxing (10”x 10”) made with 18mm thick plywood as per drawing with 1-6” horizontal extension at the top including providing and fixing 6 mm thick square frosted glass at a height of 5”-11” above Finished Floor level. 1’-9” high boxing (5”x 5”) made with 12 mm thick plywood finished with 1 mm thick laminate are to be provided. Telescopic CPU Stand/ ready made Keyboard tray shall be provided of approved model and make. Footrest made with T.W. member of size 4”X1 ½ “ finished with french polish. Drawer units as per drawing shall be provided and each drawer should have vertical partitions for keeping the currency notes and multipurpose Godrej locks. Facia of drawer unit shall be finished with 1mm thick laminate and all other sides shall be finished with white enamel paint. The drawers will be provided with handles (Stainless Steel finish) and channels as per approval of the Project Consultant / Bank. Boxing as per drawing made with 12mm thick plywood finished with Synthetic enamel paint shall be provided below the table top for electrical conduiting and at the bottom for the LAN cabling/Telephone wire conduiting. The item to include all necessary hardware and fittings in Stainless Steel finish, lipping to all edges and making provision only for electrical fitting behind the Vertical drop and also in the 10”x10” boxing as shown in the drawing. Necessary beading with matching melamine polish for fixing the glass are to be provided as per drawing/ as directed. SOLID FULL HEIGHT PARTITION Providing & fixing in position solid Full Height Partition in frame work including door in 2’x 2’ grid (horizontally and vertically) comprising of 2”x 1½” T.W. Section with 6 mm thick plywood on both sides finished with 1 mm thick laminates of approved make and colour as shown in drawing. Item to include 2” x 2” T.W. member for door frame. All exposed T.W. surfaces to be finished in melamine polish of matching laminate colour as directed including all necessary Stainless Steel finish fittings/ hardware, door closers, Godrej locks and wood preservative paint etc. as per list of approved material and as approved by the Project Consultant/ Bank complete in all respects. (Note: In case of false ceiling, the vertical T.W. members to be fixed with pucca ceiling but the area of partition payable will be below

Sq.Ft.

225

Page 4 of 10

Interior Work

the false ceiling only). 10 PARTLY GLAZED FULL HT PARTITION Providing and fixing in position partly glazed Full Height Partition work as shown in the drawing including door as shown in the drawing in frame work at 2’ x 2 ‘ grid (horizontally and vertically) comprising of 2” x 1½” T.W. Section and / or as per frame work shown in the drawings with 6mm plywood on both sides finished with 1 mm thick laminates of approved shade and colour as shown in drawings. Item to include 8 mm thick glass with etching and frosting as per design and 2”x 2” T.W. member for door sides and glass sides and T.W. door frame to take 8 mm thick glass with etching and frosting. All exposed T.W. surfaces to be finished in melamine polish of matching laminate colour as directed including all necessary Stainless Steel finish fittings/ hardware, door closers, Godrej locks and wood preservative paint etc. as per list of approved material and as approved by the Project Consultant/ Bank complete in all respects. (Note: In case of false ceiling, the vertical T.W. members to be fixed with pucca ceiling but the area of partition payable will be below the false ceiling only). ( cost including film 3M /Garware in glass)

Sq.Ft.

725

12 PARTLY GLAZED PARTITION FOR CASH CABIN Providing and fixing in position 7’-7” high partly glazed partition for Cash Cabins as per drawing including door drawing in frame work at 2’ x 2 ‘ grid (horizontally and vertically) comprising of 2” x 1½” T.W. Section and / or as per frame work shown in the drawings with 6mm plywood on both sides finished with 1 mm thick laminates of approved shade and colour as shown in drawings. Item to include 8 mm thick glass with etching and frosting as per design and 2”x 2” T.W. member for door sides and glass sides and T.W. door frame to take 8 mm thick glass with etching and frosting. The door will be provided with T.W. louvers finished in melamine polish of matching laminate colour. The doors are also to be provided with Godrej Night Latch. Two wooden trays are also to be provided as per drawing. Necessary cutouts are to provided in the glass and the edges of the glass cutouts are to be finished in mirror polish. All exposed T.W. surfaces to be finished in melamine polish of matching laminate colour as directed including all necessary Stainless Steel finish fittings/ hardware, door closers, Godrej locks and wood preservative paint etc. as per list of approved material and as approved by the Project Consultant/ Bank complete in all respects

Sq.Ft.

392

13 PARTLY GLAZED LOW HEIGHT PARTITION Providing and fixing in position partly glazed low height partition (2 1/2" thick) in frame work with T.W vertical members at 2’ c/c and 3 horizontal members at equal distance comprising of 2”x 1½” T.W. Section with 6 mm plywood on both sides finished with 1 mm thick laminates of approved make and shade as shown in drawing or . Item to include 12 mm thick glass (clear/frosted) to be fixed as shown in drawing. The exposed edges of the glass to be finished in mirror polish. T.W runner should be melamine polished in matching colour of laminate etc complete in all respects.

Sq.Ft.

64

No.

4

11 Deleted

14 MANAGER'S TABLE & OFFICER'S TABLE Providing and fixing in position Manager’s Table of size 5'-6"x 2'-6" as per drawing / Officer’s Table of size 5'-0" x 2’-3” as per drawing including Side Storage(Credenza) 3'-6" X 2'-6"X 1'-4" deep by using 25mm thick plywood for top and 18 mm thick plywood for all other horizontal and vertical members. Telescopic CPU Stand/ ready made Keyboard tray shall be provided of approved model and make. Footrest made with T.W. member of size 4”x 1 ½ “ finished with melamine polish. Side Storage ( Credenza) as per

Page 5 of 10

Interior Work

drawing shall be provided. Facia of Side Storage (Credenza) shall be finished with 1mm thick laminates as shown in the drawing and all other sides shall be finished with white enamel paint. The Side Storage (Credenza) shall be provided with handles (Stainless Steel finish) and channels as per approval of the Project Consultant / Bank. All exposed plywood surfaces to be finished with 1mm thk. laminate of approved make & shade, and all exposed edges of table top & ply verticals to have T.W.lipping. All exposed T.W. sections to be melamined and internal surfaces to have white white enamel paint as directed. Item to include plywood boxing, all necessary hardware and fittings in Stainless Steel finish, lipping to all edges etc. complete in all respects. 15 Deleted Sq.Ft.

200

Sq.Ft.

80

22 ROLLER BLINDS ( location as directed by architect) Sq.Ft. VISTA screen roller blind with headrail ELITE fabrics are Polyvinyl-C fabrics with 5% openness enabling approximately 70% shade. The polymer coating enables to give glare control and hence it would be easy to work on screens while still enjoying the view from the window. The composition of fabric also includes 25% Polyester. Two widths available in this fabric are 2000 mm and 2500mm. Thickness around 0.65 mm with tolerance of +5% and weight 470 gsm with tolerance of + 5%. Fire Resistance test specifies AS 1530-2, AS1530-3; NFPA 701:2004 Method 1; BS 5867-2 Type B. Colour fastdness of grade 7 according to the Xenon arc lamp test (ISO 105 BO2 1994). A strong fabric with tensile strength in accordance to test reports; ISO 13934-2-1999;

90

16 FULL HT STORAGE/ LOW HT STORAGE/ BACK STORAGE (CREDENZA) Providing and fixing in position Full height Storage / Low Height Storage/ Back Storage(Credenza) as shown in Drg. respectively using Plywood of required thickness finished with 1mm thick laminates as shown in the drawing . The Storage Units shall be provided with handles (Stainless Steel finish) as per approval of the Project Consultant / Bank All exposed plywood surfaces to be finished with 1mm thk. laminate of approved make & shade and all exposed edges of plywood to have T.W.lipping. All exposed T.W. sections to be melamined in matching colour laminate and internal surfaces to have white enamel paint as directed. Item to include all necessary hardware and fittings in Stainless Steel finish, Godrej multi purpose locks including magnetic ball catcher etc., complete in all respects 17 Deleted 18 Deleted 19 Deleted 20 Alumuniun Deco grill on Cash Cabin top / side P & F Al. deco grill in approved design and drawings on top of the cash cabins / rear door with intermediate SS / wooden support (polished) complete in all respect . 21 Deleted

23 WRITING LEDGE P & F Wiriting Ledge as per design and drawings with shelf and pigeon hole to keep slips made out of 19mm thick block board fabrication approved pattern laminate as per design in drawings and divisions below and shutters in the bottom to create storage spaces complete inside enamelled paint, all external side finished in approved shade 2 colour lamnate combination 1.0mm thick 24

Nos.

1

NOTICE / DISPLAY BOARD

Page 6 of 10

Interior Work

P & F pin up boards fabricated with 12mm ply and soft board back up board covered with velvet/ cloth of approved colour, framed with TW moulding on all sides complete fine finished. ( Location & size as per BM / Architect)

Sq.Ft.

50

Total for Interior Works

Rs.

BOQ FOR ELECTRICAL WORKS S.No

Description

1

MAINS WIRING Wiring for sub mains / light/ power curcuits with designated PVC insulated copper conductor cable in recessed / surface PVC conduit 2.0mm thick with suitable junction boxes, bends etc. including earthing from the distribution board as required

a. b. c. d.

3 C 10 Sqmm 3 CX 6 Sqmm 3C X 4 Sqmm 4C 2.5 Sqmm copper cables

2

LIGHT & FAN FIXTURES P & F accessories as per the following details and making connections:

a.

PHILIPS -TBS 300/236 Mirror Optic twin tube light recessed

Unit

Qty

Rate

R.Mt. R.Mt. R.Mt. R.Mt.

60 200 350 50

Nos.

25

Amount

false ceiling mounted including 2X36 W PL lamps complete or equv. b

PHILIPS Downlighters FBH-150/118 including 1x18 PL Lamps or equv.

Nos.

25

c

P & F Wall Fans -Crompton/ Bajaj/ Usha- 400mm sweep ( shade as directed by Architect)

Nos.

17

d

P & F Exhaust Fans ( heavy duty) -Crompton/ Bajaj/ Ushamake

Nos.

6

e

P & F Patti tubelight on walls - Philips /Bajaj including tube rod.

Nos.

15

f

P & F 18 W CFL including holder & necessary connectons

Nos.

4

3

INTERNAL WIRING Wiring for light point/ fan point/ exhaust fan point/ call bell point with 2.5 sq.mm FR PVC insulated copper conductor single core cable in recessed PVC conduit 2mm thick, with modular type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required including making of circuits with 2X4 Sqmm PVC insulated copper cables. (All wiring items include provision of PVC conduit and all fittings / conduit accessories complete wiring and modular switches & sockets etc.) Nos.

60

b. Wiring as above for two light point controlled by one 6A switch

Nos.

20

c.

Nos.

20

d. Wiring as above for universal 3/5Pin 6 A power socket with switch outlet point

Nos.

10

e. Wiring as above for glow sign board with switch in ATM

Nos.

1

I.

a.

Wiring as above for one light point controlled by one 6A switch

Wiring for extension points controlled by existing switches

Page 7 of 10

Interior Work

Room ( Complete Work) II.

Wiring for Power points with 2X2.5 Sqmm FR PVC insulated copper conductor single core cable in recessed PVC conduit alonwith one no. of 2.5 Sqmm FR PVC insulated copper conductor for loop earthing as required including making of circuits with 2X4 Sqmm PVC insulated copper All wiring items include provision of PVC conduit and all fittings / conduit accessories complete wiring and modular switches.

a. Wiring as above for 6 pin 16A socket with modular switch outlet point i.

Wiring as above for one switch per curcuit

Nos.

18

ii.

Wiring as above for two switches per curcuit

Nos.

4

Nos.

11

iii. Wiring etc. as above for UPS 3 sockets controlled by one 16A switch III

Wiring for Power points with 2X4 Sqmm FR PVC insulated copper conductor single core cable in recessed PVC conduit alonwith one no. of 4 Sqmm FR PVC insulated copper conductor for loop earthing as required including making of circuits with 2X10 Sqmm PVC insulated copper All wiring items include provision of PVC conduit and all fittings / conduit accessories complete wiring and modular switches.

i

Wiring as above for AC Point including MCB box with 25 A SP MCB complete including metal clad industrial sockets.

Nos.

9

ii.

Wiring as above including providing DB in ATM Room for providing power including MCB box with 25 A DP MCB complete (Load Line)

Job

1

iii

Wiring as above including providing DB in ATM Room for providing power to glow sign including MCB box with 16 A DP MCB complete

Job

1

Nos.

1

B. Supply, erection, testing and commissioning of 8 way SPN MCB disrtribution board comprising of recessed sheet steel enclosure with double door with loose wire box 63 A tinned copper bus bars neutral and earth strips inter connections etc. compete with follwing mountings as required. i. 100 A ELCB 4P as incoming -1 NO. ii. 10-25 A SP MCB -12 No

Nos.

1

C. Supply, erection, testing and commissioning of 4 way SPN MCB distribution board comprising of of recessed sheet steel

Nos.

1

Nos.

1

4 DISTRIBUTION BOARDS A. Supply, erection, testing and commissioning of 12 way SPN MCB disrtribution board comprising of recessed sheet steel enclosure with double door with loose wire box 100 A tinned copper bus bars neutral and earth strips inter connections etc. compete with follwing mountings as required. i. ii.

i. ii.

63A 4P MCB as incoing -1 No. 6-20A Amp SP MCB 10 nos.

enclosure with double door with loose wire box etc. complete with following mountings as required 63 A ELCB 4P as incoming -1 No. 63A 6P MCB -1 no.

D. Supply, erection, testing and commissioning of 40A DP MCB for input/ out of UPS connections comprising of of recessed sheet steel enclosure with loose wire box etc. complete in all respects

Page 8 of 10

Interior Work

5 i.

EARTHING Earthing with copper plate electrode 600X600X3mm including accessories and providing masonry enclosure with MS cover plate having locking arrangement, watering pipe and excavation in soil 3 mtrs minimum, including salt and charcoal as required including P & F 2 Nos 8 SWG copper wire in recess or surface for earthing as per design and detail complete in all respect as per relevant IS Code.

ii.

Supplying, laying and terminating earth connections with 8 SWG copper wire

6

CABLES P & Laying in position cables 1.1 KV PVC insulated armoured cables on saddles, clamps and inserted in GI pipe wherever exposed complete as directed

i. ii.

4C X16 Sqmm copper cables 3.5C X 50Sqmm aluminium cables

7

MAIN PANEL P & F cubical type main panel of 18 SWG CRCA sheet steel C type base MS channel for grouting on the floor complete with MCCB, MCB meters, CT etc. complete in all respect, insulated bus bars, with heat shrinkable PVC Sleeve in suitable BUS bar Chamber wiring, name plates, danger plates, earth bus etc. comprising of compartments with hinged doors and rubber gaskets, cab;e alleys on both sides, bus bar chamber with bolted doors and rubber gaskets etc. The panel being of dust and vermin proof construction to be painted with primer and smoke grey paint minimum 2 coats to look attractive. The panel shall be comprising of with the followings : Incomer 160A- 1 No. 160 Amp Cu. Bus bar-1 No Digital Ammeter and voltmeter with selector switch incl CT/PT Genset Onload Changeover 160A-1 No. Outgoings : 40A TPN MCB -10KA -2 Nos. 63A TPN MCCB-2 nos. 40A DP MCD- 3 Nos. 16-25A SP MCB -18 Nos

Nos.

2

R.Mt.

60

R.Mt. R.Mt.

20 50

Nos.

1

R.Mt.

280

Nos.

11

C. Patch Chord P & S approved make computer patch cord complete with suitable jacks at both ends

Nos.

11

D. Providing and fixing 16 PORT SWITCH (LINKSYS- MAKE)

Nos.

1

E. Providing and fixing 12U RACK for above

Nos.

1

Points

11

Nos.

1

8 A.

DATA & VOICE WORKS LAN Cabling P & F approved make - D-link / AT&T or equv. Computer LAN cabling for networking in PVC conduit / casing and capping as designed with all accessories complete as per design and details with CAT-V cable

B. I/O Outlet ( 9 + 2 in atm) P & F approved make I/O outlet points as designated places, including testing and making connection complete with all fixtures

F. Commissioning of above switches with ferrulling etc for computers G.

P & F JACK PANEL for 16 PORT SWITCH - D-LINK

Page 9 of 10

Interior Work

9

WIRING FOR TELEPHONE / EPABX.

A. S & F TAG BLOCK - KRONE MAKE for 15 Pairs

Nos.

1

B. Supplying, laying and terminating and colour code identification on either ends 0.6mm dia annealed tinned screen protected copper conductor PVC sheathed TWO PAIR telephone cable in PVC 2.0mm thick conduits as required, including s & f modular type telephone outlet housed in zinc passivated box/ PVC box with suitable connector strip in recessed wall/ partitions as required

R.Mt.

140

C. S & F modular type telephone outlet 1 Pair cord outlet

Nos.

9

D. S & L 6 pair telephone cable in PVC conduit as main line including all connections and all accessories etc.

R.Mt.

40

Total for Electrical Work

Rs.

BOQ FOR CIVIL & ALLIED WORKS 1

OIL BOUND DISTEMPER ( WALLS /RCC CEILINGS/BEAM) Providing and applying 2 coats ( first coat with brush and final coat with Roller) of OBD of approved make and shade on all surfaces and heights to give an even shade including primimg coat and full putty after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth etc., all material and labour complete ( all heights)

Sq.Ft.

4550

2

SYNTHETIC ENAMEL PAINT ON STEEL/WOOD SURFACE Sq.Ft. Providing and applying 2 coats of synthetic enamel paint 1st quality of approved manufacturer and shades on steel surface to give an even shade including two coats of red oxide primer ( all heights)

2300

3

FLUSH DOOR - TOILETS/STORE/ELECTRICAL ROOM Providing and fixing solid core flush door in single leaf 35mm thick commertial plywook of seasoned wood without ventilator. Door frame to be made of 60mm x 100mm teak wood with wrough iron hold fasts. Door to be fitted with brass fitting-hinges, handles on both sides, tower bolts, etc., complete. Frame to be painted in three coats of synethic enamel paint over a coat of wood primer including scrapping, surface preparation etc., complete.Door(leaf) to be laminated on both sides with laminations 1.5 mm thk and approved color of approved make/brand.

Sq.Ft.

120

4

SS RAILING - STAIRCASE & MEZZANINE Fabricating and fixing S. S. Railing with 40 mm SS tube & 25 mm dia SS pipe ( SS of 304 grade) as per the drawing. The item includes fabrication, buffing of the railing upto req. finish, fixing the railing at position with M 20 grade concrete, finising wall & floor properly etc. complete

R.Ft

50

4

MS COLLAPSIBLE GATE - ENTRANCE (as per design)

Sq.Ft

42

5

TOUGHENED GLASS (FRONT UPPER PORTION) Frameless Toughened glass Partiton including sun film in front portion with all harwares (Dorma Glass 12 mm thk fitting with all hardwars / associaries /patch fittings /scaffoldings )

Sq.Ft.

220

Kgs

550

Sq Ft

300

6

MS GRILL FOR FRONT OPENINGS ( quantity will be measured as per IS standards)

7

HALF BRICK WALL IN PLASTER ON BOTH SIDES

Total for Civil Work

Page 10 of 10

Rs.

Interior Work