ASEAN WORKING GROUP ON LEGAL METROLOGY (WG3) MATRIX INFORMATION ON LEGAL METROLOGY REGIME IN ASEAN
INDONESIA I.
GENERAL INFORMATION
Population Size
(2008) 228,523,300 persons
Domestic Trade per million population (in US$)
− Gross National Product/population = US$ 1,758.138 − Gross National Product/million population = US$ 1,758,138,000
Departmental Budget per million population (in US$)
Directorate of Metrololgy (2008) − Budget/population = US$ 3,536,755.2/228,523,300 = US$ 0.0155 − Budget/million population = US$ 3,536,755.2/228,523,300 = US$ 15,500
Staff Strength
Directorate of metrology and Regional Verification Offices : Administration Staff : 172 persons Inspector : 658 persons
II.
RATIONALE FOR LEGAL METROLGY LEGISLATION
COUNTRY Indonesia
III.
RATIONALE FOR LEGISLATION To establish the effective and efficiency of legal metrology system in order to increase the competitiveness of domestic products and services at global market and also consumer and producer protection.
REGULATORY BODY
Item 3.1.4, 2008-2010 WG3 Workplan
Page 1 of 8
ASEAN WORKING GROUP ON LEGAL METROLOGY (WG3) MATRIX INFORMATION ON LEGAL METROLOGY REGIME IN ASEAN
COUNTRY Indonesia
IV.
LEGISLATIVE FRAMEWORK
COUNTRY Indonesia
V.
REGULATORY BODY Directorate of Metrology, Directorate General of Domestic Trade, Ministry of Trade
LAWS AND REGULATIONS Law Number 2 Year 1981 on Legal Metrology
PATTERN APPROVAL Country
Indonesia
Total Product
8
Weighing & Measuring Instrument Type or Grouping Non-Automatic Weighing Instrument Fuel Dispenser kWh meter Water meter Oil and Gas Meter
Domestic Standards
-
Please tick box if mandatory
STANDARDS Relevant International Standards
Extent of Alignment
State reason if MOD
OIML R 76
OIML R117
Item 3.1.4, 2008-2010 WG3 Workplan
Page 2 of 8
ASEAN WORKING GROUP ON LEGAL METROLOGY (WG3) MATRIX INFORMATION ON LEGAL METROLOGY REGIME IN ASEAN Taxi Meter Volume Instruments Moisture Meter
VI.
-
MODE OF REGULATION AND TYPES OF CONFORMITY ASSESSMENT REGIMES FOR WEIGHING AND MEASURING INSTRUMENTS FOR TRADE USE
COUNTRY Indonesia
TYPES OF CONFORMITY ASSESSMENT REGIMES Registration of approved patterns
MODE OF REGULATION The patterns of all weighing and measuring instruments for trade use have to undergo pattern testing (evaluation type testing by accredited testing labs or those recognized by OIML). Directorate of Metrology through issuing authority will assess the test report and supporting documents to decide on pattern approval. All approved patterns will be entered into the Register of Approved Patterns.
Verification of weighing and measuring instruments
All weighing and measuring instruments for trade use shall be verified by Regional Verification Offices. For specific usage instruments, Directorate of Metrology did the test. Instrument meeting the prescribed requirements are stamped and deemed fit for trade used.
Post-market surveillance
Verification Inspectors from Regional Verification Offices have the general supervision and all the powers and discretion under the Legal Metrology Law and Consumer Protection Law.
Item 3.1.4, 2008-2010 WG3 Workplan
Page 3 of 8
ASEAN WORKING GROUP ON LEGAL METROLOGY (WG3) MATRIX INFORMATION ON LEGAL METROLOGY REGIME IN ASEAN VII. FLOW CHART OF MEMBER COUNTRIES’ REGIME FOR PATTERN APPROVAL Flow Chart for Type Approval
)-$ ( ) +'.( 0
) * (( $ ! (+) '!!
)-$ ( ) +'.( 0(! )! $/$+
) *'(!( ) (!' ( !)
) *'(!( !) ) , ( ( -(!( . ! )
) *'(!( !) 0$ ( /(*)/ ! )
! !
'!! (
" #$% &
0$
$ (/ ( ( . ! )
"
Item 3.1.4, 2008-2010 WG3 Workplan
Page 4 of 8
ASEAN WORKING GROUP ON LEGAL METROLOGY (WG3) MATRIX INFORMATION ON LEGAL METROLOGY REGIME IN ASEAN
VIII. MODE OF REGULATION ON VERIFICATION AND FREQUENCY FOR RE-VERIFICATION COUNTRY Indonesia
IX.
TYPE OF INSTRUMENT
RE-VERIFICATION FREQUENCY
Non-Automatic Weighing Instrument Fuel Dispenser kWh meter Water meter Oil and Gas Meter Taxi Meter Volume Instruments
Mandatory
MODE OF REGULATION ON VERIFICATION All weighing and measuring instruments for trade use shall be verified by Regional Verification Offices except the specific usage measuring instruments are verified by Directorate of Metrology.
VERIFICATION SEAL (IN PICTORIAL FORM)
09 2009 mark
Failure mark
guarantee mark
Item 3.1.4, 2008-2010 WG3 Workplan
Page 5 of 8
ASEAN WORKING GROUP ON LEGAL METROLOGY (WG3) MATRIX INFORMATION ON LEGAL METROLOGY REGIME IN ASEAN Sizes : a. “2009” mark : 6 mm, 4 mm, and 2 mm b. Failure mark : 6 mm, 4 mm, and 2 mm c. Guarantee mark : 8 mm, 5 mm, 4 mm, and 2 mm
Other marks : Region mark : 8 mm, 6 mm, 4 mm, and 3 mm Officer initial mark : 8 mm, 5 mm, and 4 mm
Item 3.1.4, 2008-2010 WG3 Workplan
Page 6 of 8
ASEAN WORKING GROUP ON LEGAL METROLOGY (WG3) MATRIX INFORMATION ON LEGAL METROLOGY REGIME IN ASEAN X. FLOWCHART OF MEMBER COUNTRIES’ REGIME FOR VERIFICATION
Trader requires instruments to be verified and stamped
Repairer, installer or manufacturer to service, repair and calibrate.
Conducting Verification Test
No
Yes Instrument verified and issued a verification stamped
Weighing and Measuring Instrument fit used for trade
Item 3.1.4, 2008-2010 WG3 Workplan
Page 7 of 8
ASEAN WORKING GROUP ON LEGAL METROLOGY (WG3) MATRIX INFORMATION ON LEGAL METROLOGY REGIME IN ASEAN XI.
PRE-PACKAGED GOODS
Country
Types of Prepackaged Goods
Indonesia
Food and Drinking Water Coffee, Sugar, Milk Sauces Fruits Cocktail Instant Noodle
XII.
Domestic Standards SNI (National Standard)
Please tick box if mandatory
STANDARDS Relevant International standards OIML R87 OIML R79
Extent of Alignment
Agency in charge of Labeling
State reason if MOD
Ministry of Trade Ministry of Health Ministry of Agriculture
CONTACT PERSON
COUNTRY Indonesia
CONTACT DETAILS Name: Amir Saharuddin Sjahrial Designation: Director Organisation: Directorate of Metrology, Directorate General of Domestic Trade, Ministry of Trade Address: Jalan Pasteur No.27 Bandung 40171 Indonesia Tel: +62 22 420 3597 Fax: +62 22 420 7035 Email:
[email protected] or
[email protected] Website: www.djpdn.go.id or www.depdag.go.id
Item 3.1.4, 2008-2010 WG3 Workplan
Page 8 of 8