REESE TOWPOWER
Up to 800 lb TW Up to 8000 lb GTW
1
2
3
Up to 2500 lb TW Up to 18000 lb GTW
5
4
6
7
2
1
Applications are listed alphabetically by make, followed by model and year.
2
3
4
5
6
4
5
6
8 7 2
3
4
2 Hitch Style
Indicates Square Tube (n) design or Round Tube (l) design.
3 Hitch Number 4 Hitch Footnotes
Footnotes reference additional information pertinent to the installation of each hitch. See right side of each application spread for explanations of each abbreviation.
5 Wrenches
Listing of each size wrench needed for hitch installation.
6 Drill Bits
On hitches that require drilling, we list the sizes needed. "NO DRILL" is listed for hitches that do not require drilling.
7 Installation Time
Times are based on common mechanical practices and should be used as an estimate as actual installation times may vary.
8 Receiver Weight Ratings
Weight Carrying refers to the total load the hitch is capable of pulling. Weight Distributing is the total load capacity of the hitch when a weight distribution system is properly used. Numbers listed are in thousands (ie. 5 = 5,000 lb).
9 T-Connector
11 Electrical Footnotes
10 Standard Wire
12 O.E.M. Replacement
Reese Towpower® T-connectors require no splicing of wires. Simply unplug your vehicle's wiring harness connector and insert the T-connector. No special tools required.
Applies to bare wires that can be spliced into the vehicles wiring system by using an electrical connection device. Use the appropriate size electrical butt style connector for best results. IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
APPLICATIONS GUIDE
1 Vehicle Model/Style & Years
3
FOOTNOTE ABBREVIATIONS ø 2 No drilling required - use existing holes.5 6 8 7 n Square Tube3hitch design. 4 l Round Tube hitch design. Frame ball mount must be used to achieve maximum weight carrying rating. 7@† Ultra Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional 9installation10time. 11 12 FM On vehicles equipped with load leveling device, air pump mounting modification required. Spare6 tire repositioning modification of spare tire carrier may be required. 5FP 8and/or7 FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Footnotes Short box modelsreference require relocation ofadditional spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models information to ease installation pertinent of larger spare tires.to the installation RO ofWill not fit Silverado SS. or Standard Wiring. T-connector SA Requires drilling on 6 ft. bed models. See right side SB Will not fit models withof shorteach bed. application spread SC forMinor trimming of plastic trunk pan required. explanation of each abbreviation. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Original Hitches madeEquipment before 03/31/08 areexact rated at 1000/10,000 WC & 1200/12,000 WD. replacement SV connectors Trimming or removalfor of under body appearancefactory panel required. damaged wiring TA Trunk access required for hitch installation. to standard TF harness, For 3/4 and 1snaps ton vehiclesdirectly only. TH factory Will not fit connector. models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
MODEL
APPLICATIONS GUIDE CLASS V WIRING INSTRUCTIONS
CLASS III/IV
73 73
74
REESE TOWPOWER
REESE TOWPOWER
FootNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design.
l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating.
† Available while supply lasts. 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AB Requires four (4) 3/8” spacer blocks (#01077-011) for installation (sold separately). AC Hitch rated at 1000 lbs. GTW, 100 lbs. TW. AF Hitch is ONLY rated for weight carrying at 3500 lbs. GTW, 350 lbs. TW and DO NOT use w/weight distribution spring bars for this specific vehicle, except for long bed trucks. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AP 2 wire system w/Pulse Width Modulation (PWM). Upgraded MoluLite® required. AW Will not fit turbo models. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BM 3 wire system. Upgraded ModuLite® HD required. Multiplex Wiring System. BM 3 wire system w/Pulse Width Modulation (PWM). Upgraded ModuLite® required. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) BO Factory 7-Way models only C 2 or 3 wire system, determine at install. CA Models with dual exhaust require exhaust modification. CC Requires minimum of 19” from end of frame rail to spring shackle bracket. CE T-connector includes fuse(s) & relays(s), converter not required. Standard 2 wire system at factory tow plug. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CO Will not fit 8 ft. 2500/3500 Series with HD suspension or four door Crew Cab. CP Fits All Models without Factory Installed Receiver. 06996
Will not fit with heavy duty suspension. Will fit with full-size spare tire stowed under vehicle. Will not fit long bed models after 1999. Will not fit short wheel base with dual exhaust. See auto dealer for trailer tow wiring kit. Will not fit with tube style bumper. Will not fit 6 ft. bed pickups. 71-77 (Standard) Van: will not fit with optional large gas tank. 74-77 (Maxi) Van: includes models with optional large gas tank. DH Cannot be installed on 1987 and later vehicles with factory step bumper unless step bumper and its mounting brackets are permanently removed and standard factory bumper is installed. DS Use #33072 on 1500 models built after 11/1/02. Use #37084 on 1500 models built before 11/1/02. DU Fascia removal required. DV Will not fit short wheel base models. DY Use on 1500 models built after 11/1/02. DX Requires six 3/8” spacer blocks (#01077-011 and six 1/2-13 x 2-1/4 GRS carriage bolts (#01266-009), which are not provided (sold separately). E ModuLite® required. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EK Extended cab only. EO Requires longer ball mount. EP Fascia trimming required. F ModuLite® recommended. FB Will not fit vehicles fitted with optional 31” tires stowed under vehicle FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. G Low-side switching system. GC T-One is equipped with ModuLite® Lite module. GH Will not fit models with 34” wide frames. GO Requires hitch with packaging date code 2/15/94 or later. GW Spare tire cannot be stowed under vehicle on short wheelbase models equipped with 15” tires or full-size spare. GX Requires fabrication of “L” bracket to reposition exhaust on ‘95 and later 6 ft. box models. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or after market lower Fascia/Rollpan or Tube Bumper.
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
06996
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RH Optional 06280 draw bar required (sold separately), except for models with ZR2 & Highrider package. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RK Fits vehicles with factory and some aftermarket rollpans. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches produced before 07/21/06 are rated at 350/3500 WC. SG Hitches produced before 09/10/07 are rated at 1000/10000 WC & 1200/12000 WD. SH Hitches produced before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches produced before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SN Hitches produced before 04/28/08 are rated at 1000/10000 WC & 1200/12000 WD. SP Hitches produced before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches produced before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. ST Will not fit 2WD models with short bed. SU Hitches produced before 03/11/08 are rated at 1000/10000 WC & 1200/12000 WD. SV Trimming or removal of under body appearance panel required. T Vans with step bumpers require longer ball mounts. TA Trunk access required for hitch installation. TS Hitch without electrical bracket rated at 350/3500 WC & no WD. Hitch with electrical bracket rated at 350/3500 WC and 500/5000 WD. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. UD Fascia removal required on XR & XRS models. V For vehicles with factory installed step bumpers only. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side. X Minor fascia trimming required.
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
A
CQ CS CT CV D DA DB DG
H 3 wire system with OEM standard 2 wire harness. HA External dress panel beneath 95-97 and 03-05 vehicles must be removed for hitch installation. HB Slight fascia deformation may occur on some models. HC Will not fit with mini or full size tire stowed under vehicle. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HP Requires four (4) 7/16” x 1” x 2” spacer blocks (#01080-012) for installation. (Sold separately) HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. J Under vehicle spare tire stowage is retained. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper & brackets. JM Some early production 1994 models may require #74667. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. JV Rubber air deflector/fascia must be removed or trimmed to install hitch. K Adapter kit (#1685) required with #37081 for 1980 and later F-series pickups. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. M Will fit with heavy-duty suspension. MB Will not fit models equipped with air suspension package. MX Multiplexed wiring system. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. O Will not fit vehicles equipped with dual exhaust existing below the bumper. P For 124” wheelbase and E350 models, adapter kit (2626) is required (sold separately). PA Will not fit 124" wheelbase or E-350 models. QS Hitch rated at 2500 lb GTW, 200 lb TW. RA Do not install on 1996 models equipped with M10 fasteners. RB Hitch installation can be made easier with a “cutter” type drill bit.
75
REESE TOWPOWER
BUICK
Allure Canada Only
1/2” 1/2”
1/2”
n 06465 Ø,GP 1/2”
14, 17mm, 7/8”
1/2”
77131 77208 77144 77208 77226
TA
10mm, 3/4”
1/2”
Ø,HM,JR,KH
10mm, 11/16”
NO DRILL
Ø,HM,JR
10mm, 11/16”
NO DRILL
Ø,HM,JR,KH
10mm, 11/16”
NO DRILL
Ø,GP,I
17mm
NO DRILL
3/4”
NO DRILL
13mm, 3/4”
NO DRILL
13mm, 3/4”
NO DRILL
19mm, 3/4”
NO DRILL
10, 14, 17, 19mm
NO DRILL
3.5 5 30
15
n 44589 Ø,CS,
Ø,GP,SV
8, 10, 18mm, 3/4” NO DRILL
Ø,GP,SV
8, 10, 18mm, 3/4” NO DRILL
Ø,GP,SV
8, 10, 18mm, 3/4” NO DRILL
Ø,GP,SV
8, 10, 18mm, 3/4” NO DRILL
14, 17, 19mm
NO DRILL
30
1977
Centurion RWD
78-85
n 06003 –
Centurion FWD
86-89
n 06615 AO,GP
Centurion FWD Centurion FWD
90-91 92-99
Century Sedan
78-81
n 06073 – 20 n 06367 GP,JR n 06407 –
06996
n 33043 –
14, 17, 19mm 1/2”
13mm, 3/4”, NO DRILL 7/8”, T-20
4.5 –
3/4”, 7/8” 3/4”, 7/8” 9/16", 5/8”, 11/16” 9/16", 5/8”, 11/16” 7, 13, 15mm, 11/16” 3/4”, 9/16”
8, 13, 17mm, 1/2”, T-50, T-55, 11/16” 3/4”
6
6 60
8mm, 10mm, 1/2” 3.5 4 11/16”, T-20 8, 13, 17mm, 1/2”, 11/16” 6 6 n 44178 AA,EP T-50, T-55, 3/4” n 44590 Ø,AA,EP,GP 8mm, 18mm NO DRILL 6 6 deep socket
–
78104
–
–
– – HG HG HG HG HG HG HG – HG HG HG CH CH CH CH – BN,HG HG – HG HG CH
– – – –
– – – –
OEM REPLACE.
75
FOOTNOTES
–
WT. DISTRIB. INSTALL TIME
–
WT. CARRYING
78104
7.5 45
NO DRILL NO DRILL
DRILL BITS
–
5
19mm, 3/4” 19mm, 3/4”
WRENCHES
60
35 35 30 30
FOOTNOTES
–
– – – – –
5 5 – –
HITCH NUMBER
78104 78104 78104 78104 78104
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
100
– – – – –
3.5 4 4 4
45 45 45 45
Centurion RWD
1/2”
78104 78104 78104 78104
NO DRILL
25 25 25
n 06384 GP,JR n 51183 GP,JR n 06003 –
10, 13, 15mm, 9/16”
30
– – – –
30
35 45 40 45 25
n 51093 AA,EP
n 77070 JR
78104 78104 78104 78104 – 78104 78104 78104 78104 78104 78104
3.5 5
n 44584 Ø,GP n 44646 Ø,GP
n 44531 AA,EP
05-09
74701 74701 85721 85721 – 74661 85704 – 78002 78002 85723
NO DRILL
10, 17, 19mm NO DRILL
l 44654 Ø,HM
77231 77231 77231 77231
10, 14, 17, 19mm 10, 17mm
GP,JR l 44562 Ø,†,JR l 44594 Ø,CR,JR
30 n 06130 Ø
n n n n
78104 78104 78104 78104 78104 78104 78104 78104 78104 – 78104 78104 78104
30 40 40 GP,JR
3/4”, 7/8”
– – 74660 74660 74660 74660 74660 74660 74660 – 74660 74660 74660
30 30
n 51159 Ø,CS,
77033 TA
STANDARD WIRE
9/16”, 3/4” 9/16”, 3/4”
T-CONNECTOR
10mm, 3/4”, 7/8” NO DRILL
14, 17mm, 7/8”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
15 15 20 20 20 15 15 n 06996 – n 06996 –
n 77247 Ø,HM,JR n 77063 Ø,HM n 77063 HM
WRENCHES
07-13
NO DRILL
FOOTNOTES
X5
3/4”
STYLE
00-06
Ø,JR
WT. CARRYING WT. DISTRIB. INSTALL TIME
X5
7/16” NO DRILL
DRILL BITS
n n n n
9/16”, 11/16” 3/4”
WRENCHES
2007 08-11 2007 08-11 04-10
BMW
†,X Ø,JR
FOOTNOTES
328i Sedan 328i Sedan 328xi Sedan 328xi Sedan X3
7/16” 7/16”
HITCH NUMBER
n 77203 Ø,EP,GP n 77210 Ø,HM,JR n 77210 Ø,HM,JR
9/16”, 11/16” 9/16”, 11/16”
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
09-13 05-11 06-11 09-12
AUDI
†,X †,X
DRILL BITS
A4 4 Dr. Sedan, Inc. Quattro A6 4 Dr. Sedan, Inc. Quattro A6 Avant Wagon, Inc. Quattro Q5
NO DRILL NO DRILL
WRENCHES
07-11 07-13 07-09 10-13 02-06 96-99 04-08 09-12 06-08 09-12 10-12
9/16”, 7/8” 9/16”, 7/8”
FOOTNOTES
MDX, All styles MDX, except models w/ full-size spare tire RDX RDX RSX SLX, All styles TL TL, All styles TSX TSX, All styles ZDX
Ø Ø
HITCH NUMBER
77025 77025 77073 77073 77073 77165 77165
IONSTALL TIME STYLE
n n n n n n n
DRILL BITS
HITCH NUMBER
97-00 2001 1997 98-99 97-99 01-03 99-03 96-01 02-04 06-10 94-01 94-01 01-06
WRENCHES
STYLE
FOOTNOTES
YEAR
1.6 EL, Canada Only 1.7 EL, Canada Only 2.2 CL 2.3 CL 3.0 CL 3.2 CL 3.2 TL 3.5 RL 3.5 RL CSX Canada Only Integra 2 Dr. Integra 4 Dr. MDX
MODEL ACURA
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
– – – – – – – – – – – – – – – – – – – – – – – – – – – –
30 30 3/8”, 1/2” 30
–
78104
–
–
–
78104
–
–
3/8”, 1/2”
30
–
78104
–
–
1/2”
40
–
78104
–
–
1/2”
–
1/2”
1/2”
10, 13, 15mm, 9/16”
1/2”
40 40
– –
78104 78058
–
– –
9/16”, 11/16”, 7/8”
3/8”
30
–
78013
–
–
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
77
APPLICATIONS GUIDE
APPLICATIONS GUIDE
REESE TOWPOWER
ACURA - BUICK
ACURA - BUICK
76
REESE TOWPOWER
REESE TOWPOWER
89-96 97-05
n 77109 TA
Century Estate Wagon RWD 78-81 Century Estate Wagon FWD 84-96 Century Wagon RWD
78-81
Century Wagon FWD
84-96
7/8”
1/2”
13mm
NO DRILL
3/4”, 7/8”
1/2”
GP,JR
3/4”, 7/8”
1/2”
–
9/16”, 11/16”, 7/8” 13mm, 7/8”
3/8” NO DRILL
3/4”
1/2”
9/16”, 11/16”, 7/8” 13mm, 7/8”
3/8”
n 06054 Ø,AI,FM n 88002 – n 06407 –
1977
Electra RWD
78-84
n 06003 –
Electra FWD, Except T Type Electra FWD Electra FWD
85-90 1985 86-89
n 88002 – n 06615 AO,GP
Electra FWD Electra Park Ave. RWD
90-91 1977
n 06073 – n 06073 – n 06003 –
Electra Park Ave. RWD
78-84
n 06003 –
Electra Park Ave. FWD Electra Park Ave. FWD
85-90 86-89
n 88002 – n 06615 AO,GP
Electra Park Ave. FWD Enclave, w/o Tow Package Enclave, w/ Tow Package Estate Wagon Full Size
1990 08-12 08-12 77-90
n 06073 –
La Crosse All, Except Super
05-09
La Crosse CX
10-13
n 06384 GP,JR n 51183 GP,JR n 06993 Ø, HM
La Crosse CXL, AWD
10-13
Ø,†,HM n – n 06993 HM
n 06142 – n 06146 HM n 06993 Ø,HM
10-13
Ø,†,HM n – n 06142 Ø
n 06146 Ø,HM La Crosse CXS
10-13
n 06993 Ø,HM
Le Le Le Le
1977 78-83 84-85 86-87
n n n n
06003 06003 06003 06409
n n n n n n
88002 06615 88002 06073 06615 88002
RWD RWD RWD FWD
Le Sabre FWD Le Sabre FWD
88-89 90-91
06996
– – – –
40 35 30
OEM REPLACE.
FOOTNOTES
STANDARD WIRE
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
40 30 30 30
– –
78013 78058
–
– –
–
78104
–
–
–
78104
–
–
–
78058
–
–
–
40 35 3/8”, 1/2” 30
–
78058
–
–
–
78104
–
–
3/8”, 1/2”
30
–
78104
–
–
1/2”
40 40
– –
78104 78104
–
1/2”
–
– –
3/4”, 9/16”
1/2”
9/16", 5/8”, 11/16” 9/16", 5/8”, 11/16” 3/4”
3/8”, 1/2”
40 30
– –
– 78104
–
– –
3/8”, 1/2”
30
–
78104
–
–
1/2” 1/2”
40 40
–
78104
–
–
1/2”
40
– 78066 74682 –
– 78058 78058 –
–
–
– 85262 85262 –
3/4” 9/16", 5/8”, 11/16” 9/16", 5/8”, 11/16” 3/4” 7, 13, 15mm, 11/16” 3/4”, 9/16”
7, 13, 15mm, 11/16” 3/4”, 9/16”
NO DRILL
1/2”
l 51083 Ø,GP,JR,RT n 06409 –
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
18mm, 3/4” NO DRILL
5
5 25
l 44569 Ø,GP,JR l 44569 Ø,GP,JR
18mm, 3/4”
NO DRILL
18mm, 3/4”
NO DRILL
5 5
5 5
25 25
–
BN BN
14mm, 9/16”, 11/16” 3/4”, 7/8”
7/16”
30
1/2”
78058
–
–
1/2”
13mm, 3/4 In, 7/8”, 9/16”
NO DRILL
30 30 20
78111
3/4”, 7/8”
85719
78104
CH
–
13mm, 3/4 In, 7/8”, 9/16” 13mm, 9/16”, 3/4”, 7/8” 13mm, 9/16”, 3/4”, 7/8” 13mm, 3/4 In, 7/8”, 9/16”
NO DRILL
20 20
85719
78104
CH
–
1/2”
20
1/2”
20
85719
NO DRILL
20
85719
NO DRILL
20 20
NO DRILL
20
85719
NO DRILL
20
85719
78104
– – – –
78104 78104 78104 78104
– –
13mm, 9/16”, 3/4”, 7/8” 13mm, 9/16”, 3/4”, 7/8” 13mm, 3/4 In, 7/8”, 9/16” 9/16", 5/8”, 11/16”
30 30 9/16", 5/8”, 11/16” 3/8”, 1/2” 30 14mm, 9/16”, 7/16” 30 3/8”, 1/2”
9/16", 5/8”, 11/16” 3/8”, 1/2”
–
11/16” 3/4”
AO,GP
7, 13, 15mm, 11/16” 1/2”
–
3/4”
1/2” 1/2”
1/2”
–
3/4”, 9/16”
AO,GP
7, 13, 15mm, 11/16” 1/2”
–
3/4”
1/2”
40 30 40 40 30 40
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
CH
78104
CH
–
CH CH
–
–
–
– – – –
78104
–
–
78104
–
–
– –
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
Electra RWD
Sabre Sabre Sabre Sabre
DRILL BITS
JR GP,JR
n 06054 Ø,AI,FM n 88002 – n 06003 –
La Crosse CXL, FWD
WRENCHES
FOOTNOTES
HITCH NUMBER
n 06200 30 n 06384 n 51183 n 06407
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Century Sedan Century Sedan
APPLICATIONS GUIDE
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
79
BUICK
BUICK
78
REESE TOWPOWER
REESE TOWPOWER
92-96
Le Sabre FWD
97-99
Le Sabre All Models
00-01
n 77070 JR
n 77070 JR
10, 13, 15mm, 9/16”
10, 13, 15mm, 9/16”
1/2”
1/2”
40
n 06615 AO,GP
7, 13, 15mm, 11/16” 3/4”
1/2”
30
1/2”
n 88002 – 20 n 06367 GP,JR n 06285 GP,JR
n 06976 HM,JR
02-05
Le Sabre Wagon Full Size
77-90
n 06409 –
Lucerne All, Except Super & Special Edition Models
06-09
n 06976 HM,JR n 51173 HM,JR,KH
OEM REPLACE.
FOOTNOTES
STANDARD WIRE
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
–
–
13, 15mm, 9/16”, 3/4”, 7/8” 15, 17mm, 9/16”, 3/4” 15, 17mm, 9/16”, 3/4” 15, 17mm, 9/16”, 3/4” 15, 17mm, 9/16”, 3/4” 14mm, 9/16”, 11/16” 15, 17mm, 9/16”, 3/4”
1/2”
35
–
78104
–
–
1/2”
30
1/2”
30
1/2”
30
–
78104
–
–
1/2”
30
7/16”
30
–
78058
–
–
1/2”
30
74696
78058
–
–
1/2”
30
NO DRILL
25
74696
78058
–
–
1/2”
–
–
–
1/2”
40 40 40 40 40 40 40
–
3/4”
–
–
–
–
–
–
–
–
–
78013
–
–
40 40
–
78013
–
–
NO DRILL
40 20
74682
78058
–
85262
3/8”
30
–
78058
–
–
1/8”, 7/16”, 60 9/16”
–
78058
–
–
n 06411 AI,JR,TA
10, 15mm, 11/16” 1/8”, 7/16”, 60 deep socket 9/16”
–
78058
–
–
n 06305 AW,FE,HB,
10, 15mm, 11/16” deep socket 10, 15mm, 11/16” deep socket
1/8”, 7/16”, 60 9/16” 1/8”, 7/16”, 60 9/16”
–
78058
–
–
–
78058
–
–
10, 15mm, 11/16” deep socket 10, 15mm, 11/16” deep socket 3/4”, 7/8”
1/8”, 7/16”, 60 9/16” 1/8”, 7/16”, 60 9/16” 1/2” 35
–
78058
–
–
–
78058
–
–
–
78058
–
–
13mm, 3/4 In, 7/8”, 9/16” 13mm, 9/16”, 3/4”, 7/8” 13mm, 9/16”, 3/4”, 7/8” 9/16”, 11/16”, 7/8” 9/16”, 11/16”, 3/4”
NO DRILL
20
85724
78104
CH
–
NO DRILL
20
NO DRILL
20
85724
3/8”
30
–
78058
–
–
3/8”
40 n 51151 HM
85261
78058
BN
–
Park Ave.
97-99
Park Ave.
00-04
n 88002 – n 06263 JR
Rainier
04-07
n 88002 – n 06142 Ø
Regal All Models
78-87
n 06407 –
Regal 2 Dr.
88-94
n 77001 AI,JR,TA
Regal 4 Dr., Except GS/Limited
1991
n 77001 AI,JR,TA
Regal GS
91-92
Regal 4 Dr., Except GS
92-94
Regal Limited
93-94
Regal 2 & 4 Dr.
95-96
Regal (Application begins with 97-1/2)
97-04
Regal, All Models
11-13
n 06993 Ø,HM
Regal, All Except GS Models
11-13
n 06142 Ø,HM
–
3/4”, 9/16”
1/2”
–
3/4”
1/2”
–
3/4”, 9/16”
1/2”
–
3/4”
1/2”
JR
13, 15, 17mm, 7/8” 3/4”
1/2”
n 06411 AI,JR,TA
JR,TA n 06411 AI,JR,TA
n 06305 AW,FE,HB,
JR,TA n 06305 AW,FE,HB, JR,TA n 06262 JR
n 06146 Ø,HM Regal Estate Wagon
82-83
n 06407 –
Rendezvous All, Inc. Ultra
02-07
n 06457 –
06996
78058
–
06073 88002 06073 88002 06073 88002 06263
n n n n n n n
20
–
–
1991
NO DRILL
40 40
–
Park Ave.
9/16”, 11/16”, 7/8”
1/2”
–
n 06125 Ø,HM,JR
l 77077 Ø,TA
10, 13, 15mm, 9/16”
78058
10-11
10, 15mm, 11/16” 1/8”, 7/16”, 40 9/16”
–
74696
Lucerne All Models
n 77001 AI,JR,TA
–
25
n 06125 Ø,HM,JR
10, 15mm, 11/16” 1/8”, 7/16”, 40 9/16” 10, 15mm, 11/16” 1/8”, 7/16”, 40 9/16”
78058
NO DRILL
08-09
1996
–
15, 17mm, 9/16”, 3/4” 15, 17mm, 9/16”, 11/16” 15, 17mm, 9/16”, 11/16” 3/4”, 9/16”
Lucerne Super & Special Edition Models
92-95
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
13, 15, 17mm, 7/8” 3/4” 13mm, 9/16”, 3/4”, 7/8” 9/16”, 11/16”, 7/8” 10, 15mm, 11/16” deep socket
1/2” 1/2” 1/2”
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
9/16”, 3/8” 11/16”, 3/4”
3.5
40
n 33061 Ø
15mm, 3/4”
n 44538 –
9/16”, 1/16”, 3/8” 3/4”
NO DRILL
3.5 –
55
3.5 –
40
CH
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 51173 HM,JR
Park Ave.
INSTALL TIME STYLE
1/2”
n 51173 HM,JR
Park Ave.
DRILL BITS
10, 13, 15mm, 9/16”
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
20 n 06367 GP,JR
n 06976 HM,JR
Le Sabre All Models
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Le Sabre FWD
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
81
BUICK
BUICK
80
REESE TOWPOWER
REESE TOWPOWER
1977
n 06003 –
Riviera
1978
n 06003 –
Riviera
95-99
n 06285 GP,JR
Roadmaster 4 Dr. Sedan
91-96
n 06003 –
Roadmaster Estate Wagon Full Size
91-96
n 88002 – n 06409 –
Skylark
92-98
n 88002 – n 06027 Ø,JR,KH
Terraza All, Inc. AWD
05-07
n 06302 AL,GP,JR
Verano, All Styles
12-13
n 77269 Ø,GP
CTS CTS 4 Dr. Sedan Only CTS-V CTS-V 4 Dr. Sedan Only De Ville FWD
03-07 08-12 04-07 08-12 86-88
n n n n
De Ville FWD
89-92
n 06616 –
De Ville FWD
1993
n 06616 –
De Ville Inc. Concours
94-96
n 06614 JR,TA
De Ville De Ville DTS Eldorado Eldorado Escalade Old Body Style
97-99 00-05 06-11 92-94 95-02 99-00
n n n n n
CADILLAC
Escalade All, Inc. EXT
77143 77143 77143 77143
13mm, 11/16”
NO DRILL
40 40 40 40 40
JR,TA
11/16”
1/8”, 1/2”
JR,TA
11/16”
1/8”, 1/2”
JR,TA
11/16”
1/8”, 1/2”
JR,TA
11/16”
1/8”, 1/2”
n 06616 –
06265 06298 06298 06157 06995
9/16", 5/8”, 11/16” 9/16", 5/8”, 11/16” 13, 15mm, 9/16”, 3/4”, 7/8” 9/16", 5/8”, 11/16” 3/4” 14mm, 9/16”, 11/16” 3/4” 7mm, 10mm, 13mm, 3/4” 10, 15mm, 3/4”, 7/8” 10, 15mm, 3/4”, 7/8”
Fleetwood RWD Seville All, Inc. SLS & STS Seville All, Inc. SLS & STS SRX All, Except Models w/Sport Package Fascia SRX STS
93-96 92-97 98-04 04-09 10-12 05-11
06996
11/16”
1/8”, 1/2”
OEM REPLACE.
–
–
–
3/8”, 1/2”
30
74487
78058
–
–
1/2”
35 30
74491
78058
–
–
NO DRILL
35 40
–
78058
–
–
1/2”
40 n 51079 AL,GP,JR
85344
78058
BN
–
1/2”
40
78104 78104 78104 78104 78104
CH
–
– – – – –
7/16” 1/2”
10, 15mm, 3/4”, 7/8”
1/2”
3.5 5 40
n 33094 AL,JR n 44574 AL,JR
10, 15mm, 3/4”, 7/8” 10, 15mm, 3/4”, 7/8”
1/2”
3.5 5
40
1/2”
3.5 5
40
3/8”, 1/2”
40
74717 78033 74717 78033 –
3/8”, 1/2”
40
–
78104
–
–
3/8”, 1/2”
40
–
78104
–
–
7/8”
40
–
78104
–
–
NO DRILL
20 20 20 40 30
– – 85778 – – 74180
78104 78104 78104 78104 – 78058
–
BN
– – – – – –
74682, 78058 85262
BN,RD
85262
74682, 78058 85262
BN,RD
85262
–
78104
–
–
–
78104
–
–
– –
78104 78104
– –
– –
– – – – –
78104 78104 78104 78104 78104
13mm, 3/4”
NO DRILL
7/8” 7/8”
1/2”, 9/16” 5 1/2”, 9/16” 5
7 30 7 30
3/4”
1/2”
7, 13, 15mm, 11/16”
1/2”
22mm, 7/8” NO DRILL 22mm, 7/8” NO DRILL
5 5
10 15 10 15
44096 44656 37074 37072
HM
7/8”
HM
7/8”
1/2”, 9/16” 6
Ø,CN,HM
22mm, 7/8”
NO DRILL
6
7 7.5 10 10
n 44095 Ø,CN,HM l 44668 Ø,CN,HM n 44145 Ø,CN
22mm, 7/8”
NO DRILL
22mm, 7/8”
NO DRILL
22mm, 7/8”
NO DRILL
5 6 6
10 20 10 15 7.5 30
n n n n
HM
7/8”
1/2”, 9/16” 5 1/2”, 9/16” 5
30 30 30 20
35 40
25 35 1/2” 35 3/8”, 1/2” 40
CH CH –
– CH – –
1/2”
–
3/4”
–
10, 13, 15mm, 9/16” 3/4”
1/2”
13mm, 3/4”
NO DRILL
9/16”, 11/16”
NO DRILL
35 20 35 l 33086 Ø,JR,KH l 44638 Ø
n 77143 JR,TA
FOOTNOTES
–
–
n 88002 – n 06157 Ø n 06617 Ø,EP,GP,JR
STANDARD WIRE
35
n 51201 Ø,CN,HM n 51201 Ø,CN,HM
78-92 89-93
T-CONNECTOR
1/2”
2002
Fleetwood Brougham Fleetwood Coupe & Sedan FWD
WT. DISTRIB. INSTALL TIME
–
NO DRILL
3/4”
WT. CARRYING
–
NO DRILL
†,AO
DRILL BITS
–
13mm, 7/8”
–
WRENCHES
–
n 51012 HM n 51012 HM
– 88002 88002 06616
FOOTNOTES
30
13mm, 3/4”
n n n n
HITCH NUMBER
3/8”, 1/2”
Ø
1977
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
–
Ø, JR
Fleetwood Brougham
DRILL BITS
–
NO DRILL
n 88002 – n 06615 †,AO
WRENCHES
–
13mm, 7/8”
85-92 86-88
FOOTNOTES
–
JR
Fleetwood FWD Fleetwood FWD
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
DRILL BITS
30
Ø
03-06
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
3/8”, 1/2”
10, 13, 15mm, 9/16” 10, 13, 15mm, 9/16” 10, 13, 15mm, 9/16” 13, 15mm, 11/16”, 7/8” 13mm, 3/4”
Escalade All, Inc. EXT & ESV
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
45
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
13, 19mm
NO DRILL
10, 19mm
NO DRILL
3.5 5 4 5
60 15
– – – – –
– – – – –
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 51102 AL,GP,JR
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Riviera
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
83
BUICK - CADILLAC
BUICK - CADILLAC
82
REESE TOWPOWER
REESE TOWPOWER
Astro Standard Body
Astro Extended Body
85-94
n n n n
90-05
06227 06037 06227 06037
Ø,CR,HM
14mm, 15mm
NO DRILL
Ø,GP,HC
14mm, 15mm
NO DRILL
Ø,CR,HM
14mm, 15mm
NO DRILL
Ø,GP,HC
14mm, 15mm
NO DRILL
n 37042 AF
n 88001 –
Avalanche
Aveo 4 Dr. Sedan Aveo 4 Dr. Sedan Aveo 4 Dr. Sedan Aveo 5 Dr. Hatchback Bel Air Bel Air Blazer Full Size Blazer Full Size Blazer Full Size Blazer Full Size
n 51201 Ø,CN,HM
03-06
–
3/4”, 7/8”
1/2”
Ø,HM,TA
3/4”
NO DRILL
Ø,HM,TA
3/4”
NO DRILL
–
3/4”, 7/8”
1/2”
n 06003 – n 06003 –
n 88001 –
9/16", 5/8”, 11/16” 3/8”, 1/2” 9/16", 5/8”, 11/16” 3/8”, 1/2”
Blazer Downsize, All Models
Blazer Downsize, All Models
Blazer Downsize, All Models
n 06955 Ø,GP
n 06955 Ø,FP,GP,KK
1998
n 06955 Ø,FP,GP,KK
99-01
n 06955 Ø,FP,GP,KK
02-05
06996
n 33057 Ø,CS,GP
15, 17mm, 3/4” NO DRILL
15,18,21mm, 7/16", 1/2" 30 n 37152 – 9/16in, 11/16 in, 3/4in, T50
18mm, 7/8”
18mm, 7/8”
18mm, 7/8”
18mm, 7/8”
NO DRILL
NO DRILL
NO DRILL
NO DRILL
OEM REPLACE.
FOOTNOTES
STANDARD WIRE
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
STYLE
DRILL BITS
WT. CARRYING WT. DISTRIB. INSTALL TIME 65
–
85217
–
–
15, 17mm, 3/4” 1/2”, 9/16” 3.5 6 NO DRILL 3.5 6
45 30
–
74051
–
–
3.5 6
30
22mm, 7/8” NO DRILL
22mm, 7/8” NO DRILL
5
5
10 15
n 37072 Ø,CN,HM
10 15
n l n n l
44095 44668 37072 44095 44668
22mm, 7/8”
NO DRILL
6
10 20
74682, 78058 85262
–
–
5 6 6 5 6
10 10 10 10 10
74682
78058
–
–
85709 85709 85709 85709 – – 74425 74425 74178 78180
78013 78013 78013 78013 78058 78058 78058 78058 78058 78058
CG
BN
– – – – – – – – – –
–
–
–
–
Ø,CN,HM
22mm, 7/8”
NO DRILL
Ø,CN,HM
22mm, 7/8”
NO DRILL
Ø,CN,HM
22mm, 7/8”
NO DRILL
Ø,CN,HM
22mm, 7/8”
NO DRILL
Ø,CN,HM
22mm, 7/8”
NO DRILL
20 15 20 20 15
30 30
l l n 15 n l l
37051 37041 51031 51031 37051 37041
n 15 n l l
51031 51031 37051 37041
n 15 n l l n
51031 51031 37051 37041 51031
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
–
3/4”, 7/8”
6
30
HM
7/8”
1/4”, 1/2”, 5 9/16”
6
30
n 44096 HM
7/8”
1/2”, 9/16” 5
7
1/2”, 9/16” 5
7 30 7 30
n 44656 HM
7/8”
1/2”, 9/16” 5
7.5 30
1/2”, 9/16” 5
NO DRILL
4
6 15
l 33015 Ø,SD
18 mm, 7/8” NO DRILL
4
6
15
1/2”
5 5 4 4 5 5
6 6 6 6 6 6
30 30 15 15 30 30
n 33021 Ø n 44098 Ø,HM
18mm, 1-1/8” NO DRILL 18mm, 1-1/8” NO DRILL
4 4
6 6
20 20
l 33015 Ø,SD n 33021 Ø,FP,KK n 44098 Ø,FP,
4 4 4
6 6 6
15 20 20
–
–
–
–
4 4 5 5
6 6 6 6
15 15 30 30
l 33015 Ø,SD n 33021 Ø,FP,KK n 44098 Ø,FP,
6 6 6
15 20 20
85262
78091
BN,RD
85262
18mm, 1-1/8” NO DRILL
4 4 4
4 4 5 5 4
6 6 6 6 6
15 15 30 30 15
18mm, 7/8” NO DRILL l 33015 Ø,SD n 33021 Ø,FP,KK 18mm, 1-1/8” NO DRILL n 44098 Ø,FP,HM,KK 18mm, 1-1/8” NO DRILL
4 4 4
6 6 6
15 20 20
–
–
–
–
JT
18mm, 1-1/8” 3/4”
JT
3/4”
1/2”
Ø,HM
18mm, 1-1/8” NO DRILL
Ø, FP, HM, KK 18mm, 1-1/8” NO DRILL FP,JT,KK
18mm, 3/4” 1/2”
FP,JT,KK
18mm, 3/4” 1/2”
Ø,HM
18mm, 1-1/8” NO DRILL
Ø, FP, HM, KK 18mm, 1-1/8” NO DRILL FP,JT,KK
18mm, 3/4” 1/2”
FP,JT,KK
18mm, 3/4” 1/2”
Ø,HM
18mm, 1-1/8” NO DRILL
Ø, FP, HM, KK 18mm, 1-1/8” NO DRILL FP,JT,KK
18mm, 3/4” 1/2”
FP,JT,KK
18mm, 3/4” 1/2”
Ø,HM
18mm, 1-1/8” NO DRILL
3/4”, 7/8” 3/4”, 7/8”
HM,KK
HM,KK
18mm, 7/8”
1/2”
1/2”
NO DRILL
18mm, 1-1/8” NO DRILL 18mm, 1-1/8” NO DRILL
18mm, 7/8”
NO DRILL
18mm, 1-1/8” NO DRILL
30 30 30 30
30
– –
1/4”, 1/2”, 5 9/16”
– –
7.5 7.5 7.5 10
CG CG
5 5 1/2” 5 1/2”, 9/16” 6
7/8”
15 n 51031 Ø,HM
33042 33042 33042 37074
CG
n n n n
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 7/8”
n 51012 HM n 51012 HM
95-97
6
15, 17mm
45
30 20 20 30
n 37042 –
Blazer Downsize, All Models
1/4”, 1/2”, 5 9/16”
n 33057 CR,HM n 44010 Ø,CS,GP
3.5 6
74051 n 51201 Ø,CN,HM
77098 n 77181 n 77181 77097
NO DRILL
1/4”, 1/2”, 5 9/16”
15, 17mm, 3/4” NO DRILL
7/16", 1/2" 0
2002
04-06 2006 07-11 04-11 1977 78-81 73-75 76-84 85-91 92-94
3.5 6 30 6 65
15, 17mm 15,17,18, 19, 21, 22mm, T-50, 9/16”, 3/4” 15,17,18, 19, 21, 22mm, T-50, 9/16”, 3/4”
n 33057 Ø,CR,HM
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
BN BN BN
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
Avalanche
15, 18, 21mm, 9/16", 11/16", 3/4", T50
WRENCHES
FOOTNOTES
HITCH NUMBER
30 30 30 n 51029 CS,GP 30 n 37152 AF
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL CHEVROLET
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
85
CHEVROLET
CHEVROLET
84
REESE TOWPOWER
93-96
n 77006 JR
7/8”
9/16”
40
97-02
n 77006 JR
7/8”
9/16”
40
10-11
n 77223 Ø,GP
13mm, 9/16”
NO DRILL
12-13
n 77223 Ø,GP
13mm, 9/16”
NO DRILL
n 51163 GP,JR Cavalier Z-24
2002
n 77069 JR,KH
Cavalier All, Except LS Sport
03-05
n 77049 GP,JR n 51163 GP,JR
Cavalier LS Sport
03-05
n 77069 JR,KH
Cavalier Z-24 (Canada Only)
03-05
n 77069 JR,KH
Celebrity Wagon Cobalt 2 Dr., Except SS Models Cobalt 4 Dr., Except SS Models Cobalt Sport 2 Dr.
84-90 05-10 05-10 08-10
Cobalt Sport 4 Dr.
08-10
Cobalt SS 2 Dr., Incl. Supercharged Models
05-10
Cobalt SS 4 Dr.
05-10
Cobalt, 2 Dr. Cobalt, 4 Dr. Colorado All Models
77122 77122 77132 51164 77132 51164 77132
JR
3/4”
OEM REPLACE.
FOOTNOTES
STANDARD WIRE
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
78058 78058 78058
– – –
– – –
–
78058
–
–
74491
78058
–
–
– – – – –
30 30 9/16" 5/8”, 11/16” 3/8”, 1/2” 30 3/4” 1/2” 35 14mm, 9/16”, 7/16” 30 9/16" 5/8”, 11/16” 3/8”, 1/2”
9/16" 5/8”, 11/16” 3/8”, 1/2”
11/16” 3/4”
14mm, 9/16”, 11/16”
1/2” 7/16”
35 30
n 33007 –
13, 14mm, 3/4”
13/32”
3.5 10 40
30
–
78058
–
–
7/16”
40
–
78058
–
–
7/16”
40
1/2”
40
–
78058
–
–
40
– –
78058 78058
–
7/16”
–
– –
7/16”
40
7/16”
40
–
78058
–
–
7/16”
40
1/2”
40
–
78058
–
–
7/16”
40
–
78058
–
–
7/16”
40
1/2”
40
–
78058
–
–
1/2”
40
–
78058
–
–
40 40 25 25 25 25 25
– 78043 78035 78043
78058 78058 78058 78058
–
1/2”
BN
– – – –
78035
78058
BN
–
78043
78058
BN
–
78035
78058
BN
–
78043 78035 78001
78058 78058 78013
BN BN
– – 85262
85262
74682, BO 85262
JR
3/4”
1/2”
HM,JR
3/4”
1/2”
HM,JR
3/4”
1/2”
3/4”
1/2”
HM,JR
3/4”
1/2”
HM,JR
3/4”
1/2”
n 51164 HM,JR n 77132 HM,JR n 51164 HM,JR
3/4”
1/2”
3/4”
1/2”
3/4”
1/2”
13mm, 7/8”
NO DRILL
40
25 25 25
n 51074 Ø,GP
06996
HITCH NUMBER
– – 74487
06003 06003 06003 88002 06409
7/16”
HM,JR
2011 2011 04-07
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
–
n 06054 Ø,AI,FM n n n n n n n
DRILL BITS
–
n 77049 GP,JR
n 77049 GP,JR
WRENCHES
–
95-99
2002
FOOTNOTES
–
Cavalier All, Except Z-24
Cavalier All, Except Z-24
STYLE
15
n 77101 †,TA
n 51163 GP,JR
WT. CARRYING WT. DISTRIB. INSTALL TIME
–
88-90
13mm, 9/16”, 11/16” 13mm, 9/16”, 11/16” 13mm, 9/16”, 11/16” 13mm, 9/16”, 11/16” 13mm, 9/16”, 11/16” 13mm, 9/16”, 11/16” 13mm, 9/16”, 11/16” 13mm, 9/16”, 11/16” 13mm, 9/16”, 11/16”
DRILL BITS
CH
Cavalier 2 & 4 Dr., Except Z-24
n 77049 GP,JR
WRENCHES
78104
n 88002 – n 06409 –
95-02 00-01
FOOTNOTES
85710
91-96
Cavalier All, Inc. RS & Z-24 Cavalier All, Inc. Z-24
HITCH NUMBER
15
Caprice Estate Wagon
n 77069 JR,KH
INSTALL TIME STYLE
–
77-90
95-99
DRILL BITS
–
Caprice Estate Wagon
Cavalier Z-24
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
78013
n n n n n
n 51163 GP,JR
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
–
1977 78-90 91-96
13mm, 11/16”, 3/4” 13mm, 9/16”, 11/16” 13mm, 9/16”, 11/16” 13mm, 9/16”, 11/16”
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Camaro Inc. Z-28 & SS, Except w/Dual Exhaust Pipes On Drivers Side Camaro Inc. Z-28 & SS, Except w/Dual Exhaust Pipes On Drivers Side Camaro All Models, except convertible & dealer-installed ground effects Camaro All Models, except convertible & dealer-installed ground effects Caprice Caprice Caprice
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
21, 22mm, 11/16”
NO DRILL
6
7.5 25
n 44593 Ø,GP
21, 22mm, 11/16”
NO DRILL
6
7.5 25
BN BN
BN,CG
–
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
87
APPLICATIONS GUIDE
APPLICATIONS GUIDE
REESE TOWPOWER
CHEVROLET
CHEVROLET
86
REESE TOWPOWER
13mm, 11/16”, 3/4”
n 77232 Ø,GP, † n 77269 Ø,GP
11/16”
NO DRILL
13mm, 11/16”
NO DRILL
NO DRILL
07-09
n 51185 Ø,HM n 06391 Ø,HM
18,19mm, 3/4”
Equinox
18,19mm, 3/4”
NO DRILL
25 25 n 51193 Ø,HM
n 51185 Ø,HM
18,19mm, 3/4”
NO DRILL
25
n 06391 Ø,HM
18,19mm, 3/4”
NO DRILL
25 n 51193 Ø,HM
n 51185 Ø,HM
18,19mm, 3/4”
NO DRILL
25
n 06099 Ø,HM
7/8”
NO DRILL
15 n l l n
9/16”, 11/16”, 7/8” 3/8” NO DRILL
30 25 n 51193 Ø,HM
51023 37051 37041 37152
Ø,HM HM HM HM
n 37042 HM
n 06099 Ø,HM
00-02
6
15, 18, 21mm, 9/16In, 11/16In, 3/4In ,T50 7/8”
NO DRILL
15 n l l n
51023 37051 37041 37152
Ø,HM HM HM HM
n 06099 Ø,HM
l 37041 HM n 37152 HM n 37042 HM
06996
15, 18, 21mm, 9/16", 11/16", 3/4", T50
7/16",1/2" 30
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
BO
–
– – 85732
74682, 85262 – 78058 78104
– CH
– – –
–
OEM REPLACE.
85262
FOOTNOTES
WT. DISTRIB. INSTALL TIME
WT. CARRYING
85262
3.5 4
30
– 78028
78058 78013
CG
– –
NO DRILL
3.5 4 30
n 44630 Ø,†,HM n 44637 Ø,HM
18,19mm, 3/4” NO DRILL
18,19mm, 3/4”
18,19mm, 3/4” NO DRILL
3.5 4 3.5 4
30 30
74709
78013
CE
–
18,19mm, 3/4”
NO DRILL
3.5 4 30
n 44630 Ø,†,HM n 44637 Ø,HM
18,19mm, 3/4” NO DRILL
3.5 4 3.5 4
30 30
85716
78104
–
85779
n 44630 Ø,†,HM n 37004 Ø,HM
3.5 4 30 5 10 20
85716 74659
78104 78013
–
3/4”
HG
85779 74866
– –
HG
5 3/4” 1/2” 5 3/4” 1/2” 5 15,17,18, 19,21, 1/4”, 1/2”, 5 3/4”, 7/8”
NO DRILL
22mm,T-50, 9/16” 9/16”,3/4” 15,17,18, 19,21, 1/4”, 1/2”, 5 22mm,T-50, 9/16” 9/16”,3/4”
10 6 6 6
15 35 35 30
6
30
5 5 3/4” 1/2” 5 15,17,18, 19,21, 1/4”, 1/2”, 5 3/4”, 7/8”
NO DRILL
3/4”
1/2”
22mm,T-50, 9/16” 9/16”,3/4” 15,17,18, 19,21, 1/4”, 1/2”, 5 22mm,T-50, 9/16” 9/16”,3/4”
10 6 6 6
15 35 35 30
6
30
n 37004 Ø,HM
5 5 3/4” 1/2” 5 15,17,18, 19,21, 1/4”, 1/2”, 5 3/4”, 7/8”
NO DRILL
3/4”
1/2”
22mm,T-50, 9/16” 9/16”,3/4” 15,17,18, 19,21, 1/4”, 1/2”, 5 22mm,T-50, 9/16” 9/16”,3/4”
10 6 6 6
15 35 35 30
6
30
n 37004 Ø,HM
n 44028 Ø,HM
n 88001 HM
BN,CG
18,19mm, 3/4” NO DRILL
n 44028 Ø,HM 15, 18, 21mm, 9/16", 7/16",1/2" 30 11/16", 3/4", T50 7/8” NO DRILL 15 n 51023 Ø,HM l 37051 HM
78013
n 44637 Ø,HM
18,19mm, 3/4” NO DRILL
18,19mm, 3/4” NO DRILL
3/4”, 7/8”
NO DRILL
NO DRILL
5
3/4”
NO DRILL
5
n n 10 30 n n
41921 96921 45007 96946
@,HM, †
13/16”, 15/16” 9/16”
@,HM
13/16”, 15/16” 9/16”
Ø,#,HM,TF
3/4”
@,HM
13/16”, 15/16” 9/16”
3/4”, 7/8”
3/4”
3/4”, 7/8”
NO DRILL
NO DRILL
NO DRILL
5 5
5
NO DRILL
10 12 10 12 12 14 10 13
35 74659 35 74659 45 35 74659
10 20
85246
n 96921 @,HM n 88001 HM
78001
3.5 4 30
n 41921 @,HM, †
2003
DRILL BITS
7.5 25
NO DRILL
7/16", 1/2" 30
n 37042 HM
Express Van Full Size
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS NO DRILL
18,19mm, 3/4”
n 44028 Ø,HM n 88001 HM Express Van Full Size
WRENCHES
FOOTNOTES
STYLE
DRILL BITS
WT. CARRYING WT. DISTRIB. INSTALL TIME
WRENCHES
FOOTNOTES
18,19mm, 3/4”
10-13 96-99
21, 22mm, 11/16”
10 30 n 45007 Ø,#,HM,TF n 96946 @,HM
13/16”, 15/16” 13/16”, 15/16” 3/4” 13/16”, 15/16”
–
HG
– –
HG
78013
HG
74866
9/16”
10
12 35 85246
–
HG
–
9/16”
10
12 35 85246
–
HG
–
NO DRILL
12 14 45 10 13 35 85246
9/16”
10 20
74886
n 41921 @,HM, †
13/16”, 15/16” 9/16”
10
12 35
n 96921 @,HM
13/16”, 15/16” 9/16”
10
12 35 78029
n 45007 Ø,#,HM,TF n 96946 @,HM
3/4”
NO DRILL
13/16”, 15/16”
9/16”
12 10
14 45 13 35 78029 74051
HG
78013
–
74866
–
HG
–
10 30
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
89
APPLICATIONS GUIDE
n 06407 – n 06391 Ø,HM
Equinox All, Except V6 Models Express Van Full Size
n 44593 Ø,GP
7.5 25
15 15
78-87 05-06
10-13
6
1/2”, 1” hole saw 35
El Camino Equinox
Equinox All Models
NO DRILL
STANDARD WIRE
n 77260 –
21, 22mm, 11/16”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW T-CONNECTOR
97-04 87-96 11-13
HITCH NUMBER
n 51074 Ø,CP,GP
08-12
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Colorado All Models
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
Corvette Corsica Cruze All Models
APPLICATIONS GUIDE
REESE TOWPOWER
CHEVROLET
CHEVROLET
88
REESE TOWPOWER
REESE TOWPOWER
HM
3/4”
HM
15,17,18, 19,21, 9/16” 22mm,T-50, 9/16”,3/4” 15,17,18, 1/4”, 1/2”, 5 19,21, 9/16” 22mm,T-50, 9/16”,3/4”
n 37042 HM
10 6 6 6
15 35 35 30
6
30
n 37004 Ø,HM
n 88001 HM HHR HHR SS Impala Impala Impala All Models Impala All Models Impala SS Kodiak C4500 Cab & Chassis w/34 Wide Frames
06-11 08-10 1977 78-85 00-05
n n n n
77132 51164 77132 51164
HM,JR
3/4”
1/2”
HM,JR
3/4”
1/2”
HM,JR
3/4”
1/2”
EP,HM,JR
3/4”
1/2”
77082 – 51099 –
06-12 94-96
11/16”, 7/8”
1/2”
11/16”, 7/8”
1/2”
15, 18, 21mm, 9/16", 11/16", 3/4", T50
3/4”
3/4”, 7/8”
NO DRILL
5
5
n 41921 @,HM, † n 96921 @,HM
13/16”, 15/16” 9/16”
n 45007 Ø,#,HM,TF n 96946 @,HM
13/16”, 15/16” 9/16”
06003 06003 06389 51188 06389 51188 06003 88002
– – Ø,GP,JR Ø,GP,JR Ø,GP,JR Ø,GP,JR – –
60 n 33068 †,AL n 33068 †,AL
06996
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
13mm, 9/16” 1/2” 13mm, 9/16” 1/2”
– – 85735
78058 78058 78058
– – –
– – –
74694
78013
BN
–
74487
78058
–
–
OEM REPLACE. –
FOOTNOTES BN
WT. DISTRIB. INSTALL TIME
WT. CARRYING
78058
21mm, 9/16” 13/16”, 7/8” 21, 24mm, 11/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8”
15
16 35 –
–
–
–
15
16 35 –
15
16 35 –
–
–
–
15
16 35 –
–
–
–
15
16 35 –
15
16 35 –
–
–
–
15
16 35 –
–
–
–
15
16 35 –
15
16 35 –
–
–
–
15
16 35 –
–
–
–
15
16 35 –
15
16 35 –
–
–
–
15
16 35 –
–
–
–
15
16 35 –
n 96947 @
13mm, 3/4”, 9/16” NO DRILL
78043
n 96940 @
n 96940 @
n 06022 Ø,JR
–
–
n 41940 @, †
99-10
l 77259 AI
BN
–
n 96947 @
95-00 90-92 1993
78058
–
n 96940 @
Lumina All Models Lumina APV Van Lumina APV Van
78043
14 45 13 35 78029 74051
16 35 –
n 41940 @
99-10
10, 15mm, 11/16” 1/8”, 7/16”, 60 deep socket 9/16”
–
15
n 96947 @
n 06411 AI,JR,TA
HG
21mm, 9/16” 13/16”, 7/8”
n 41940 @, †
99-10
10, 15mm, 11/16” 1/8”, 7/16”, 40 9/16” 13mm, 3/4” 1/2” 30
–
n 41940 @, †
n 41940 @
n 77001 AI,JR,TA
–
12 10
30 30 3/4” NO DRILL 30 3/4” NO DRILL 30 3/4” NO DRILL 30 3/4” NO DRILL 30 9/16", 5/8”, 11/16” 3/8”, 1/2” 30 3/4” 1/2” 35
99-10
90-94
NO DRILL
9/16", 5/8”, 11/16” 3/8”, 1/2”
99-10
Lumina All, Except Z-34
3/4”
9/16", 5/8”, 11/16” 3/8”, 1/2”
n 96940 @
Kodiak C8500 Cab & Chassis w/34 Wide Frames
CH
12 35 12 35 78029
25 25 25 35 n n 20 n 20 n n n n n
78058
10 10
7/16", 1/2" 30
n 96947 @
Kodiak C7500 Cab & Chassis w/34 Wide Frames
13/16”, 15/16” 9/16”
78029
10 30
n 96940 @
Kodiak C6500 Cab & Chassis w/34 Wide Frames
DRILL BITS
10 20
n 96947 @ Kodiak C5500 Cab & Chassis w/34 Wide Frames
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS NO DRILL
3.5 3.5 30 3.5 3.5 30
21mm, 9/16” 13/16”, 7/8” 21, 24mm, 11/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8” 21, 24mm, 11/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8” 21, 24mm, 11/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8” 21, 24mm, 11/16” 13/16”, 7/8”
–
–
–
–
–
–
78058
–
–
– – 74492
78058 78058 78058
– –
– – –
–
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 44028 Ø,HM
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
5 5 1/2” 5 1/4”, 1/2”, 5 NO DRILL
1/2”
STANDARD WIRE
3/4”, 7/8” 3/4”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW T-CONNECTOR
Ø,HM HM
DRILL BITS
51023 37051 37041 37152
WRENCHES
15 n l l n
FOOTNOTES
DRILL BITS NO DRILL
HITCH NUMBER
7/8”
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
n 06099 Ø,HM
04-13
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Express Van Full Size
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
91
CHEVROLET
CHEVROLET
90
REESE TOWPOWER
78-83 97-03 04-07 06-07 08-12 08-12 04-05 2008
Monte Carlo Monte Carlo All, Inc. Z-34 Monte Carlo Inc. SS (Will not fit SS Sport Appearance Pkg.) Monte Carlo Inc. SS (Will not fit SS Sport Appearance Pkg.) Orlando, Canada Only Pickup, C/K Series w/6 ft. Bed Pickup, C/K Series w/6 ft. Bed
n 77076 Ø,GP
13mm, 3/4”
13mm, 3/4”
NO DRILL
NO DRILL
n 15 n n n n n 15 n n
06407 06249 06988 06988 06658 06658 06249 06988
78-88 95-99 00-05
l 77259 AI l 77185 TA
13mm, 3/4”
1/2”
7/8”
1/2”
n 77268 Ø,HM,JR,KH 13mm, 11/16”
NO DRILL
–
9/16”, 11/16”, 7/8” 3/8”
Ø,HM
13mm, 9/16”, NO DRILL 3/4”, 7/8” 9/16”, 11/16”, 7/8” 3/8” 13mm, 7/8”
–
30 60 30
n 06358 Ø,JR
13mm, 7/8”
–
30
13mm, 3/4”, 9/16” NO DRILL
OEM REPLACE.
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
3.5 3.5 30
–
–
–
BN
– – – – – – – –
78013
BN
–
74716 74716 –
78013 78013 –
BN BN
– – –
– – –
78058 78058 78013
–
– – –
–
78058
–
–
– 74425
78058 78058
– BN
– –
74178
78058
BN
–
– BN BN BN – –
–
– –
35 n 33065 CQ,DX,FP n 33065 CQ,DX,FP n 44108 CQ,FP,GU,
HM,HX n 44109 CQ,FP,GP, GU,HX n 33065 CQ,DX,FP n 44108 CQ,FP,GU, HM,HX n 44109 CQ,FP,GP, GU,HX
Pickup, C/K Series w/6 ft. Bed 85-87
1/2”
5 5 6
8 30 8 40 10 30
1/2”
6
10 30
1/2” 1/2”
5 6
8 40 10 30
1/2”
6
10 30
3/4”, 7/8”
1/2”
3/4”, 7/8”
1/2”
18mm, 3/4” deep socket 18mm, 3/4” deep socket 3/4”, 7/8” 18mm, 3/4” deep socket 18mm, 3/4” deep socket
Pickup, C/K Series w/6 ft. Bed 88-00 2 Dr. Extended Cab, Inc. Sportside Fenders
n 41909 @,EK,
13, 18, 19mm, 13/16”, 15/16”
9/16”
10
13 30 85741
78058
BN
–
n 96909 @,EK,
13, 18, 19mm, 13/16”, 15/16”
9/16”
10
13 30 85741
–
BN
– –
HM,SS, †
HM,SS
Pickup, C/K Series w/6 ft. Bed 88-00 2 Dr. Regular & Extended Cabs, Inc. Sportside Fenders l 37069 – n 37096 CA,HX n 51022 Ø,GP n 51016 HM,FP n 51017 GP,FP n 51021 Ø,HM,J Pickup, C/K Series w/6 ft. Bed 88-00 Equipped w/Aftermarket Roll Pan Pickup, C/K Series w/6 ft. Bed 88-00 Regular & Extended Cabs, Inc. Sportside Fenders w/10 Deep Drop Bumper
9/16”, 3/4” 1/2” 15,17,18, 19,21, 22mm, 9/16”,3/4” 13, 18, 19mm, 3/4” 13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8” 13, 18, 19mm, 7/8”
5
1/4”, 1/2”, 5 9/16”
15/16", 3/4” 5/8”
7
12 40
85741
78058
BN
l 37094 –
15/16", 3/4” 5/8”
7
12 40
74180
78058
99-00 Classic – Only
5
10 25
6
10 30
6
10 30
5
5.5 40
85741
78058
BN
–
6
10 20
85741
78058
BN
–
7.5 40 6.5 90
NO DRILL
5
10 20
3/16”, 9/32”, 1/2”, 17/32” 3/16”, 9/32”, 1/2”, 17/32”
5
10 40
5
10 40
5
10 20
NO DRILL
l 37034 Ø
n 44105 Ø,GP
13, 18, 19mm, NO DRILL 3/4”, 7/8” n 44108 CQ,FP,GU, 18mm, 3/4” 1/2” HM,HX deep socket n 44109 FP,GP, GU,HX 18mm, 3/4” 1/2” deep socket
n 96522 CO,HK n 37080 Ø,FS,J
06996
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
DRILL BITS
13mm, 9/16” 1/2”
1/2”
n 06407 – 30 n 06022 Ø,JR 20 n 06358 Ø,JR
06-07 2012 67-72 73-84
06388 06388 06407 06146
n 33068 †,AL
40
WRENCHES
25 25 30 20
n n n n
FOOTNOTES
1/2” 1/2”
04-05 06-07 78-83 2013
HITCH NUMBER
3/4” 3/4”
n 06988 JR,X
STYLE
– –
2008
WT. CARRYING WT. DISTRIB. INSTALL TIME
74716
– JR
DRILL BITS
50
GP,JR,RB GP,JR,RB
WRENCHES
13mm, 11/16”, 3/4” 3/8”
JR JR,X
FOOTNOTES
78058 – 78013 78013 78058 78104 – 78013
13mm, 3/4”
HITCH NUMBER
– – 74716 74716 78066 – – 74716
– –
5, 10, 13mm, 7/8” #11 (.191 DIA.), 1/2” 9/16”, 11/16”, 7/8” 3/8”
INSTALL TIME STYLE
30 20 13mm, 11/16”, 3/4” 3/8” 40 13mm, 11/16”, 3/4” 3/8” 50 11/16”, 3/4” 1/2”, 3/8” 45 11/16”, 3/4” 1/2”, 3/8” 45 13mm, 3/4” 1/2” 20 13mm, 11/16”, 3/4” 3/8” 40
FOOTNOTES
78058
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
74492
n 06091 AL,GP n 77076 Ø,GP
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
STANDARD WIRE
Malibu All Models Malibu 4 Dr. Malibu 4 Dr. Sedan Only Malibu SS 4 Dr. Sedan Only Malibu All, Except LTZ Malibu LTZ Malibu Classic 4 Dr. Old Body Style Malibu Classic 4 Dr. Sedan Only (Old Body Style) Malibu Classic SS 4 Dr. Sedan Only (Old Body Style) Malibu Maxx Malibu Maxx All, Except SS Malibu Wagon Malibu, All Styles
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
T-CONNECTOR
94-96
STYLE
YEAR
MODEL
Lumina APV Van
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
FOOTNOTES
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
13, 18, 19mm, NO DRILL 7/8”
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
93
APPLICATIONS GUIDE
APPLICATIONS GUIDE
REESE TOWPOWER
CHEVROLET
CHEVROLET
92
REESE TOWPOWER
REESE TOWPOWER
5
10 40
n 37087 FP
3/4”, 7/8”
1/2”
6
10 45 n 96938 @,GP
13/16”, 7/8” 9/16”
12
15 40
n 41940 @, †
21mm, 9/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8” 21, 24mm, 11/16” 13/16”, 7/8”
15
16 35
15
16 35
15
16 35
n 96940 @ n 96947 @ n 37081 M n 33065 FP n 37087 FP
n 51017 CQ,GP,JT n 88001 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
7/16", 1/2"
3/16”, 9/32”, 1/2”, 17/32” 3/16”, 9/32”, 1/2”, 17/32”
5
10 40
5
10 40
10 30
–
78058
–
–
3/4”, 7/8”
1/2”
8 30 10 45
78058
BN
–
1/2”
5 6
74425
3/4”, 7/8”
BN BN
n 44108 FP,GU,
18mm, 3/4” HM,HX deep socket n 44109 FP,GP, GU,HX 18mm, 3/4” deep socket
1/2”
6
10 30
1/2”
6
10 30
n 37081 M n 33065 FP n 37087 FP
n 51016 CQ,HM,JT n 51017 CQ,GP,JT
BN
– – –
15
16 35 74425
–
BN
–
13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8”
3/16”, 9/32”, 1/2”, 17/32” 3/16”, 9/32”, 1/2”, 17/32”
5
10 40
5
10 40
21, 24mm, 11/16” 13/16”, 7/8”
15
BN
74425
78058
BN
–
3/4”, 7/8”
1/2”
8 30 10 45
78058
BN
–
1/2”
5 6
74178
3/4”, 7/8”
BN BN
n 44108 FP,GU,
18mm, 3/4” HM,HX deep socket n 44109 FP,GP, GU,HX 18mm, 3/4” deep socket
1/2”
6
10 30
1/2”
6
10 30
13/16”, 7/8” 9/16” 13/16”, 7/8” 9/16” 21mm, 9/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8”
12 12 15
15 40 74178 15 40 74178 16 35 74178
– – –
BN
– – –
15
16 35 74178
–
BN
–
7/16", 1/2" 35
74178
Pickup, C/K Series w/8 ft. Bed 85-87 w/Deep Drop Bumper Pickup, C/K Series w/8 ft. Bed 88-91 4 Dr. Crew Cab
n 51017 CQ,GP,JT
13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8”
3/16”, 9/32”, 1/2”, 17/32” 3/16”, 9/32”, 1/2”, 17/32”
5
10 40
5
10 40
15
BN
5
10 40
74178
78058
BN
–
n 33065 FP
3/4”, 7/8”
1/2”
5
8
85741
78058
BN
–
n 37087 FP
3/4”, 7/8”
1/2”
6
10 45 BN BN
30
n 44108 FP,GU,
18mm, 3/4” HM,HX deep socket n 44109 FP,GP, GU,HX 18mm, 3/4” deep socket
1/2”
6
10 35
1/2”
6
10 35
13/16”, 7/8” 9/16” 13/16”, 7/8” 9/16” 21mm, 9/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8”
12 12 15
15 40 74178 15 40 74178 16 35 74178
– – –
BN
– – –
15
16 35 74178
–
BN
–
35
74178 n 96947 @
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
16 35 74178
13, 18, 19mm, NO DRILL 7/8”
n 96940 @ n 51016 CQ,HM,JT
21, 24mm, 11/16” 13/16”, 7/8”
n 37081 M
n 41938 @,GP, † n 96938 @,GP n 41940 @, †
7/16", 1/2"
16 35 74425
10 40
n 96947 @
06996
– – –
5
n 96940 @
15, 18, 21mm, 9/16", 11/16", 3/4", T50
15 40 74425 15 40 74425 16 35 74425
13, 18, 19mm, NO DRILL 7/8”
n 41938 @,GP, † n 96938 @,GP n 41940 @, †
n 88001 –
21mm, 9/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8”
12 12 15
74425
Pickup, C/K Series w/8 ft. Bed 73-84 w/Deep Drop Bumper Pickup, C/K Series w/8 ft. Bed 85-87
15, 18, 21mm, 9/16", 11/16", 3/4", T50
13/16”, 7/8” 9/16” 13/16”, 7/8” 9/16”
35 n 96947 @
n 88001 –
–
5
n 96940 @ 13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8”
–
13, 18, 19mm, NO DRILL 7/8”
n 41938 @,GP, † n 96938 @,GP n 41940 @, †
n 51016 CQ,HM,JT
–
21, 24mm, 11/16” 13/16”, 7/8”
15
16 35 74178
BN
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
Pickup, C/K Series w/8 ft. Bed 63-72 w/Deep Drop Bumper Pickup, C/K Series w/8 ft. Bed 73-84
OEM REPLACE.
15 40 –
FOOTNOTES
12
STANDARD WIRE
13/16”, 7/8” 9/16”
30 n 41938 @,GP, †
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
8
DRILL BITS
5
WRENCHES
1/2”
FOOTNOTES
3/4”, 7/8”
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
n 33065 FP
DRILL BITS
10 40
WRENCHES
WT. CARRYING
n 51017 CQ,GP,JT
5
FOOTNOTES
3/16”, 9/32”, 1/2”, 17/32” 3/16”, 9/32”, 1/2”, 17/32”
STYLE
DRILL BITS
13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
WT. CARRYING WT. DISTRIB. INSTALL TIME
WRENCHES
n 51016 CQ,HM,JT
HITCH NUMBER
FOOTNOTES
Pickup, C/K Series w/8 ft. Bed 63-72
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
95
CHEVROLET
CHEVROLET
94
REESE TOWPOWER
REESE TOWPOWER
n 37096 CA,HX
15,17,18, 19,21, 22mm, 9/16”,3/4”
1/4”, 1/2”, 9/16”
5
85741
78058
BN
–
l 37034 Ø
15/16", 3/4” 5/8”
7
12 40
l 37094 –
15/16", 3/4” 5/8”
7
12 40
74180
78058
99-00 Classic Only
–
7.5 40
6.5 90 n 41901 @,DB,
18, 19mm, 9/16” GP,SN, † 13/16”, 7/8” n 96901 @,DB, GP,SN 18, 19mm, 9/16” 13/16”, 7/8”
n 51016 HM n 51017 GP
13, 18, 19mm, 3/4” 13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8”
NO DRILL
5
10 20
3/16”, 9/32”, 1/2”, 17/32” 3/16”, 9/32”, 1/2”, 17/32”
5
10 40
5
10 40
5
10 20
n 44105 Ø,GP
13, 18, 19mm, NO DRILL 3/4”, 7/8” 18mm, 3/4” 1/2” n 44108 FP,GU, HM,HX deep socket n 44109 FP,GP, GU,HX 18mm, 3/4” 1/2” deep socket
5
10 25
6
10 30
6
10 30 n 45006 #,TF
n 51021 Ø,HM,J n 88001 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
13, 18, NO DRILL 19mm, 7/8”
3/4”
1/2”
13 30 85741
–
BN
–
10
13 30 85741
–
BN
–
12
14 45
7/16", 1/2" 35
74180
Pickup, C/K Series w/8 ft. Bed 88-00 Equipped w/Aftermarket Roll Pan Pickup, C/K Series w/8 ft. Bed 88-00 Regular & Extended Cabs, w/10 Deep Drop Bumper Pickup, C/K Series w/8 ft. Bed 92-00 4 Dr. Crew Cab
n 96522 CO,HK
l 37069 Ø
n 37096 CA,HX
9/16”, 3/4” 1/2”
5
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4”
5
5.5 40
85741
78058
BN
–
n 37080 Ø,FS,J
13, 18, 19mm, NO DRILL 7/8”
6
10 20
85741
78058
BN
–
n 36007 Ø
18mm, 3/4”
5
10 40
85741
78058
BN
–
l 37034 Ø
15/16", 3/4” 5/8”
7
12 40
l 37094 Ø
15/16", 3/4” 5/8”
7
12 40
74180
78058
99-00 Classic Only
–
NO DRILL
7.5 40
6.5 90 n 41901 @,DB,
18, 19mm, 9/16” GP,SN, † 13/16”, 7/8” n 96901 @,DB, GP,SN 18, 19mm, 9/16” 13/16”, 7/8”
n 51022 Ø,GP
13, 18, NO DRILL 19mm, 3/4”
n 51016 HM
13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8” 13, 18, 19mm, 7/8”
5
10 20
3/16”, 5 9/32”, 1/2”, 17/32” 3/16”, 5 9/32”, 1/2”, 17/32”
10 40
n 44105 Ø,GP
13, 18, 19mm, NO DRILL 3/4”, 7/8”
5
n 51017 GP
n 51021 Ø,HM,J Pickup, C/K Series w/8 ft. Bed 92-00 4 Dr. Crew Cab, w/10 Deep Drop Bumper 85-00 Pickup, C/K Series, Cab & Chassis w/34 Wide Frames
NO DRILL
5
13 30 85741
BN
10
13 30 85741
BN
3/4”
1/2”
12
14 45
10 40
10 20 n 37080 Ø,FS,J
13, 18, 19mm, NO DRILL 7/8”
6
10 20
–
–
–
–
n 41938 @,CC, †
13/16”, 7/8” 9/16”
12
15 40 –
–
–
–
n 96938 @,CC n 41940 @, †
13/16”, 7/8” 9/16”
12 15
15 40 – 16 35
–
–
–
15
16 35 –
–
–
–
15
16 35 –
n 96940 @ n 96947 @
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
10
10 25 n 45006 #,TF
06996
10
21mm, 9/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8” 21, 24mm, 11/16” 13/16”, 7/8”
–
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 51022 Ø,GP
OEM REPLACE.
10 40
FOOTNOTES
5
NO DRILL
WT. DISTRIB. INSTALL TIME
18mm, 3/4”
WT. CARRYING
n 36007 Ø
DRILL BITS
–
WRENCHES
BN
FOOTNOTES
78058
HITCH NUMBER
85741
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE 10 40
DRILL BITS
5
WRENCHES
13, 18, 19mm, NO DRILL 7/8”
FOOTNOTES
STANDARD WIRE
5
T-CONNECTOR
9/16”, 3/4” 1/2”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
n 37081 M
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
Pickup, C/K Series w/8 ft. Bed 88-91 4 Dr. Crew Cab w/Deep Drop Bumper Pickup, C/K Series w/8 ft. Bed 88-00 2 Dr. Regular & Extended Cabs l 37069 Ø
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
97
CHEVROLET
CHEVROLET
96
REESE TOWPOWER
REESE TOWPOWER
21, 22mm, 3/4” 21, 22mm, 3/4” 21mm, 3/4”
NO DRILL
6
10.5 15
NO DRILL
6
7.5 15
NO DRILL
7.5 12 20 7 12 25
n 37016 Ø,RO l 37034 Ø,RO l 37069 Ø,RO n 37096 Ø,JL,RO
9/16”, 3/4” 1/2” 15,17,18, 19,21, 22mm, 9/16”,3/4”
5
1/4”, 1/2”, 5 9/16”
15/16", 3/4” 5/8”
n 88001 DB,RO
15, 18, 21mm, 9/16", 11/16", 3/4", T50
NO DRILL
5
7.5 15
l 37094 Ø,RO
15/16", 3/4” 5/8”
7
12 25
l 44564 Ø,JL,RO
21mm, 3/4”, NO DRILL 7/8”
6
8
21mm, 7/8”
NO DRILL
21mm, 3/4”,7/8”
NO DRILL
5
7.5 15
l 33093 Ø,JL
21mm, 3/4”, NO DRILL 7/8”
6
8
l 51081 Ø,RT,JL
21, 22mm, 3/4”
NO DRILL
6
10.5 15
l 44563 Ø,JL
21, 22mm, 3/4” 21mm, 3/4”
NO DRILL
6
10.5 15
NO DRILL
7.5 12 20 6 7.5 15
l 37069 Ø n 37096 Ø,JL,RO
9/16”, 3/4” 1/2”
5
15,17,18, 19,21, 22mm, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
21mm, 3/4”,7/8”
NO DRILL
21, 22mm, NO DRILL 3/4” 15/16", 3/4” 5/8” 15/16", 3/4” 5/8”
7 7
12 25 12 25
99-00 Classic Only
–
5
6
8
l 51081 Ø,RT,JL l 51072 Ø,RT,JL
7.5 15
l 44564 Ø,JL
21mm, 3/4”,7/8”
NO DRILL
9/16”, 3/4” 1/2”
21, 22mm, 3/4” 21mm, 3/4”,7/8”
5
5
7.5 15
l 33093 Ø,JL
21mm, 3/4”, NO DRILL 7/8”
78071
–
BN,RD
–
78071
–
BN,RD
–
12
14 20
15
7/16", 1/2" 35
Pickup, Silverado 2500 LD 99-02 6.6 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan
21mm, 3/4”, NO DRILL 7/8”
6
21mm, 3/4”
8
15
n 37016 Ø l 37034 Ø,RO
15/16", 3/4” 5/8”
7.5 12 20 7 12 25
l 37094 Ø
15/16", 3/4” 5/8”
7
NO DRILL
78071
–
BN,RD
–
78071
–
BN,RD
–
NO DRILL
6
10.5 15
l 44563 Ø,JL
NO DRILL
5
7.5 15
l 44564 Ø,JL
21, 22mm, NO DRILL 3/4” 21mm, 3/4”, NO DRILL 7/8” 21, 22mm, 3/4” NO DRILL
12 25
74180
–
99-00 Classic Only
–
6
10.5 15
6
8
6
7.5 15
n 41932 Ø,@, HM,JL, † 21mm, 7/8” NO DRILL n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL
12 12
14 20 14 20
n 45009 Ø,#,TF
12
14 20
15 21mm, 3/4”
NO DRILL
85262 78071
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
RD
7.5 25
n 44619 Ø,CM
06996
RD
85262
l 37069 Ø
15, 18, 21mm, 9/16", 11/16", 3/4", T50
78058
7.5 25 6.5 35
7/16", 1/2" 35
l 51072 Ø,RT,JL
n 88001 DB
74180
14 20
15
n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL l 51072 Ø,RT,JL
Pickup, Silverado 1500 LD 99-02 8 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Silverado 2500 LD 99-02 6.6 ft. Bed, 2 & 4 WD
–
15
l 51072 Ø,RT,JL
l 37034 Ø,RO l 37094 Ø,RO
15, 18, 21mm, 9/16", 11/16", 3/4", T50
–
85262
n 37016 Ø n 44619 Ø,CM
n 88001 DB,RO
12
7/16", 1/2" 35
Pickup, Silverado 1500 LD 99-02 6.6 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Silverado 1500 LD 99-02 8 ft. Bed, 2 & 4 WD
–
RD
–
BN,RD
–
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
JL,RO
21mm, 3/4”,7/8”
–
7.5 25 6.5 35
n 96932 Ø,@,HM,
l 51072 Ø,RT,JL
OEM REPLACE.
l 44563 Ø,JL,RO
FOOTNOTES
10.5 15
STANDARD WIRE
6
15
T-CONNECTOR
NO DRILL
WT. DISTRIB. INSTALL TIME
21, 22mm, 3/4”
WT. CARRYING
l 51081 Ø,RT,JL,RO
DRILL BITS
8
WRENCHES
6
FOOTNOTES
21mm, 3/4”, NO DRILL 7/8”
HITCH NUMBER
l 33093 Ø,JL
DRILL BITS
STYLE
7.5 15
WRENCHES
WT. CARRYING WT. DISTRIB. INSTALL TIME 5
FOOTNOTES
DRILL BITS NO DRILL
HITCH NUMBER
WRENCHES 21mm, 3/4”,7/8”
HITCH NUMBER
l 51072 Ø,RT,JL,RO
n 44619 Ø,CM,RO
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
FOOTNOTES
Pickup, Silverado 1500 LD 99-02 6.6 ft. Bed, 2 & 4 WD
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
99
CHEVROLET
CHEVROLET
98
REESE TOWPOWER
REESE TOWPOWER
7.5 25 10.5 15
n 37016 Ø l 37034 Ø,RO
21mm, 3/4”
15/16", 3/4” 5/8”
7.5 12 20 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL 21mm, 3/4” NO DRILL 7 12 25 n 45009 Ø,#,TF
12 12
14 20 14 20
NO DRILL
5
7.5 15
l 37094 Ø
15/16", 3/4” 5/8”
7
12 25
l 44563 Ø,JL
21, 22mm, NO DRILL 3/4” 21mm, 3/4”, NO DRILL 7/8” 21, 22mm, NO DRILL 3/4”
6
10.5 15
6
8
6
7.5 15
l 44564 Ø,JL n 44619 Ø,CM 15, 18, 21mm, 9/16", 11/16", 3/4", T50
85262
Pickup, Silverado 2500 LD 99-02 8 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Silverado 1500 HD 01-02 6.6 ft. Bed, 2 & 4 WD
n 96944 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL HM, LT
l 37069 Ø
n 37096 Ø,JL
l 51081 Ø,RT,JL l 51072 Ø,RT,JL
21mm, NO DRILL 3/4”,7/8” 9/16”, 3/4” 1/2”
15,17,18, 19,21, 22mm, 9/16”,3/4” 21, 22mm, 3/4” 21mm, 3/4”,7/8”
5
7.5 15
l 33093 Ø,JL
5
7.5 25
6
8
n 37016 Ø l 37034 Ø
15/16", 3/4” 5/8”
7
12 25
n 88001 DB
15, 18, 21mm, 9/16", 11/16", 3/4", T50
6.5 35
l 37094 Ø
15/16", 3/4” 5/8”
7
12 25
NO DRILL
6
10.5 15
l 44563 Ø,JL
6
10.5 15
NO DRILL
5
7.5 15
l 44564 Ø,JL
21, 22mm, NO DRILL 3/4” 21mm, 3/4”, NO DRILL 7/8” 21, 22mm, NO DRILL 3/4”
6
8
6
7.5 15
21, 22mm, 3/4”, 7/8”
n 37096 Ø,JL
15,17,18, 19,21, 22mm, 9/16”,3/4” l 51073 Ø, RT, CS, FS, 21, 22mm, JL, LT 3/4”
15,17,18, 19,21, 22mm, 9/16”,3/4” 21, 22mm, n 51050 SA 3/4”, 7/8” l 51073 Ø, RT, CS, FS, 21, 22mm, JL, LT 3/4”
06996
14 20 78071
NO DRILL
12
14 20
85217
–
BN,RD
–
(with amber – bulbs)
5
10 20
l 44577
1/4”, 1/2”, 5 9/16”
6.5 40
n 44657 HM,SA
5
7.5 20
NO DRILL
NO DRILL
Ø, CS, FS, JL, LT
7/16", 1/2" 35
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
1/4”, 1/2”, 5 9/16”
6.5 40
NO DRILL
5
10 20
21, 22mm, 3/4”
NO DRILL
6
11 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25 78071
21, 22mm, 3/4”, 7/8”
1/2”
6
12 20 n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25
n 96944 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
13
16 25
13
17 25
HM, LT, †
HM, LT
13/16”, 7/8”
13/16”, 7/8”
HM, LT 13/16”, 7/8” n 45022 Ø, #, CS, FS, 18, 21mm NO DRILL LT, TF
NO DRILL
5
7.5 20
n 96944 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
13
16 25
11 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25 78071
HM, LT
l 44577 Ø, CS, FS,
JL, LT n 44657 Ø,HM,SA
21, 22mm, 3/4” 21, 22mm, 3/4”, 7/8”
NO DRILL
6
1/2”
6
–
15
RD
–
85262 n 37096 Ø,JL
15, 18, 21mm, 9/16", 11/16", 3/4", T50
12
7/16", 1/2" 35
Pickup, Silverado 2500 HD 01-02 8 ft. Bed, 2 & 4 WD
n 88001 DB
NO DRILL
RD
85262 n 51050 SA
15, 18, 21mm, 9/16", 11/16", 3/4", T50
16 25
7/16", 1/2" 35
Pickup, Silverado 2500 HD 01-02 6.6 ft. Bed, 2 & 4 WD
n 88001 DB
21mm, 7/8” HM,JL, † 7.5 12 20 n 96932 Ø,@, HM,JL 21mm, 7/8”
1/4”, 1/2”, 5 9/16”
13
13/16”, 7/8”
15 n 41932 Ø,@,
21mm, 3/4”, NO DRILL 7/8” 21mm, 3/4” NO DRILL
n 44619 Ø,CM
–
15
7/16", 1/2" 35
l 51072 Ø,RT,JL
BN,RD
HM, LT, † 12 20 n 96939 Ø, @, CS, FS, HM, LT n 45022 Ø, #, CS, FS, LT, TF n 45293 Ø, #, CS, FS, LT, TF
13/16”, 7/8”
13/16”, 7/8” 18, 21, 22mm, NO DRILL 13/16”, 7/8” 18, 21mm NO DRILL
12
15 25
13
17 25
18, 21mm
18
18 25
NO DRILL
85262
BN,RD
–
RD
–
BN,RD
–
RD
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 88001 DB
NO DRILL
–
OEM REPLACE.
WT. DISTRIB. INSTALL TIME
14 20 78071
FOOTNOTES
WT. CARRYING 12
HM,JL, †
STANDARD WIRE
DRILL BITS NO DRILL
15 n 41932 Ø,@,
T-CONNECTOR
WRENCHES 21mm, 7/8”
8
FOOTNOTES
6
HITCH NUMBER
5 6
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
NO DRILL
9/16”, 3/4” 1/2” 21, 22mm, 3/4” 21mm, 3/4”,7/8”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
21mm, 3/4”, NO DRILL 7/8”
DRILL BITS
l 33093 Ø,JL
NO DRILL
WRENCHES
7.5 15
21mm, 3/4”,7/8”
FOOTNOTES
STYLE
l 51072 Ø,RT,JL
WT. CARRYING WT. DISTRIB. INSTALL TIME
l 37069 Ø l 51081 Ø,RT,JL
5
DRILL BITS
FOOTNOTES
HITCH NUMBER
l 51072 Ø,RT,JL
WRENCHES
Pickup, Silverado 2500 LD 99-02 8 ft. Bed, 2 & 4 WD
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
101
CHEVROLET
CHEVROLET
100
REESE TOWPOWER
REESE TOWPOWER
NO DRILL
5
7.5 20
n 44657 Ø,HM,SA
21, 22mm, 3/4”, 7/8”
1/2”
6
12 20 n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
15, 18, 21mm, 9/16", 11/16", 3/4", T50
HITCH NUMBER
21mm, 3/4”,7/8”
NO DRILL
5
7.5 15
l 33093 Ø,JL
21mm, 3/4”, NO DRILL 7/8”
6
8
l 51081 Ø,RT,JL
21, 22mm, NO DRILL 3/4” 9/16”, 3/4” 1/2”
6
10.5 15
l 44563 Ø,JL
NO DRILL
6
10.5 15 n 41932 Ø,@,
5
7.5 25
n 44619 Ø,CM
21, 22mm, 3/4” 21, 22mm, 3/4” 21mm, 3/4”
NO DRILL
6
NO DRILL
7.5 12 20 n 45009 Ø,#,TF 7 12 25 7 12 25
l 51072 Ø,RT,JL
21mm, 3/4”,7/8”
NO DRILL
5
7.5 15
l 44564 Ø,JL
18, 21mm
NO DRILL
18
18 25
18, 21, 22mm, NO DRILL 13/16”, 7/8”
13
16 25
15/16", 3/4” 5/8” 15/16", 3/4” 5/8” 21mm, 3/4”, NO DRILL 7/8”
6
15
21mm, 7/8” HM,JL, † 7.5 15 n 96932 Ø,@, HM,JL 21mm, 7/8”
8
21mm, 3/4”
NO DRILL
12
14 20
NO DRILL
12
14 20
NO DRILL
12
14 20 85217
–
(with amber – bulbs)
BN,RD
–
–
BN,RD
–
l 33093 Ø,JL
21mm, 3/4”, NO DRILL 7/8”
6
8
15 n 41932 Ø,@,
NO DRILL
12
14 20 78071
l 51081 Ø,RT,JL
21, 22mm, NO DRILL 3/4” 9/16”, 3/4” 1/2”
6
10.5 15
l 44563 Ø,JL
NO DRILL
6
8
15 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL
12
14 20
5
7.5 25
n 44619 Ø,#,TF
NO DRILL
12 14 20 n 45009 Ø,#,TF
12
14 20
5
7.5 15
n 37016 Ø
21, 22mm, 3/4” 21, 22mm, 3/4” 21mm, 3/4”
NO DRILL
7.5 12 20
NO DRILL
15/16", 3/4” 5/8” 15/16", 3/4” 5/8” 21mm, 3/4”, NO DRILL 7/8”
7 7 6
HM,JL, †
21mm, 7/8”
21mm, 3/4”
NO DRILL
12 25 12 25 7.5 15 85262 –
BN,RD
–
–
BN,RD
–
–
(with amber – bulbs)
21mm, 3/4”,7/8”
NO DRILL
5
7.5 15
l 33093 Ø,JL
21mm, 3/4”, 7/8”
NO DRILL
6
8
NO DRILL
12
14 20 78071
l 51081 Ø,RT,JL
21, 22mm, NO DRILL 3/4” 9/16”, 3/4” 1/2”
6
10.5 15
l 44563 Ø,JL
21, 22mm, 3/4” NO DRILL
6
10.5 15 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL
12
14 20
5
7.5 25
n n l l
Ø,CM
21, 22mm, 3/4” NO DRILL
Ø
21mm, 3/4”
6 7.5 7 7
7.5 12 12 12
15 20 25 25
6
8
15
l 51072 Ø,RT,JL 7/16", 1/2" 35
03-05
15,17,18, 19,21, 22mm, 9/16”,3/4” 21mm, 3/4”,7/8”
1/4”, 1/2”, 5 9/16”
6.5 35
5
7.5 15
NO DRILL
44619 37016 37034 37094
NO DRILL
Ø,RO
15/16", 3/4” 5/8”
Ø
15/16", 3/4” 5/8”
l 44564 Ø,JL
21mm, 3/4”, NO DRILL 7/8”
15 n 41932 Ø,@,
HM,JL, †
21mm, 7/8”
85217
85262 78071
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
RD
78071 l 51072 Ø,RT,JL
n 37096 Ø,JL
06996
RD
–
7.5 15
21mm, 3/4”,7/8”
–
78071 5
n 37069 Ø
15, 18, 21mm, 9/16", 11/16", 3/4", T50
BN,RD
NO DRILL
03-04
n 88001 DB
–
15
7/16", 1/2" 35
03-05
RD
78071
21mm, 3/4”,7/8”
l 37034 Ø,RO l 37094 Ø l 44564 Ø,CM
Pickup, Silverado 1500 HD 6.6 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan
17 25
l 51072 Ø,RT,JL
l 51072 Ø,RT,JL
Pickup, Silverado 2500 LD 8 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Silverado 1500 HD 6.6 ft. Bed, 2 & 4 WD
13
85262
l 37069 Ø
15, 18, 21mm, 9/16", 11/16", 3/4", T50
15 25
7/16", 1/2" 35
Pickup, Silverado 2500 LD 03-04 6.6 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Silverado 2500 LD 03-04 8 ft. Bed, 2 & 4 WD
n 88001 DB
12
–
RD
–
BN,RD
–
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
l 51072 Ø,RT,JL
n 37016 Ø l 37034 Ø l 37094 Ø
15, 18, 21mm, 9/16", 11/16", 3/4", T50
13/16”, 7/8” 18, 21mm NO DRILL
85262
l 37069 Ø
n 88001 DB
HM, LT n 45022 Ø, #, CS, FS, LT, TF n 45293 Ø, #, CS, FS, LT, TF n 96944 Ø, @, CS, FS, HM, LT
7/16", 1/2" 35
Pickup, Silverado 2500 LD 03-04 6.6 ft. Bed, 2 & 4 WD
APPLICATIONS GUIDE
3/4”
BN,RD
OEM REPLACE.
l 51073 Ø, RT, CS, FS, 21, 22mm,
–
FOOTNOTES
15 25 78071
13/16”, 7/8”
STANDARD WIRE
WT. DISTRIB. INSTALL TIME
12
HM, LT, †
T-CONNECTOR
WT. CARRYING
11 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
DRILL BITS
WRENCHES
6
WRENCHES
FOOTNOTES
NO DRILL
FOOTNOTES
STYLE
21, 22mm, 3/4”
JL, LT
HITCH NUMBER
WT. CARRYING WT. DISTRIB. INSTALL TIME
l 44577 Ø, CS, FS,
DRILL BITS
DRILL BITS
10 20
HITCH NUMBER
WRENCHES
5
FOOTNOTES
NO DRILL
JL, LT
n 88001 DB
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
21, 22mm, 3/4”, 7/8”
n 51050 SA
01-02
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Pickup, Silverado 3500 Series 8 ft. Bed, 2 & 4 WD
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
103
CHEVROLET
CHEVROLET
102
REESE TOWPOWER
REESE TOWPOWER
21, 22mm, 3/4” NO DRILL
6
10.5 15 n 41932 Ø,@,HM,
5
7.5 25
n 44619 Ø,CM,RO
21, 22mm, 3/4” NO DRILL
6
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21mm, NO DRILL 5 3/4”,7/8”
6.5 35
n 37016 Ø,RO
21mm, 3/4”
7.5 12 20
7.5 15
l 37034 Ø,RO
15/16", 3/4” 5/8”
7
12 25
15/16", 3/4” 5/8”
7 6
12 25 8 15
n 37096 Ø,JL,RO l 51072 Ø,RT,JL
HITCH NUMBER
l 37094 Ø,RO l 44564 Ø,JL,RO
Pickup, Silverado 1500 LD 6.6 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Silverado 1500 LD 8 ft. Bed, 2 & 4 WD
21mm, 3/4”, NO DRILL 7/8”
21mm, 7/8”
NO DRILL
12
14 20
21mm, 7/8”
NO DRILL
12
14 20
15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50
85262
03-05 l 51072 Ø,RT,JL
03-05
l 51081 Ø,RT,JL l 37069 Ø
n 37096 Ø,JL,RO l 51072 Ø,RT,JL n 88001 DB,RO
NO DRILL
5
7.5 15
l 33093 Ø,JL
21, 22mm, 3/4” NO DRILL
6 5
10.5 15 7.5 25
6.5 35
l n n l l
7.5 15
l 44564 Ø,JL
21mm, 3/4”,7/8”
9/16”, 3/4” 1/2”
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21mm, NO DRILL 5 3/4”,7/8”
44563 44619 37016 37034 37094
21mm, 3/4”, NO DRILL 7/8”
6
8
15
Ø,JL
21, 22mm, 3/4” NO DRILL
Ø,CM
21, 22mm, 3/4” NO DRILL
6 6 7.5 7 7
10.5 7.5 12 12 12
15 n 41932 Ø,@, HM,JL, † 21mm, 7/8” NO DRILL 15 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL 20 25 25
6
8
15
Ø
21mm, 3/4”
Ø
15/16", 3/4” 5/8”
NO DRILL
Ø
15/16", 3/4” 5/8” 21mm, 3/4”, NO DRILL 7/8”
21, 22mm, 3/4”, 7/8” l 51073 Ø, RT, CS, FS, 21, 22mm, JL, LT 3/4” 15,17,18, n 37096 Ø,JL 19,21, 22mm, 9/16”,3/4”
NO DRILL
5
10 20
NO DRILL
5
7.5 20
1/4”, 1/2”, 5 9/16”
6.5 40
JL, LT n 37096 Ø,JL
l 44577 Ø, CS, FS,
JL, LT n 44657 HM,SA
21, 22mm, 3/4” 21, 22mm, 3/4”, 7/8”
NO DRILL
6
BN,RD
–
85217
–
(with amber – bulbs)
1/2”
6
–
BN,RD
–
BN,RD
12
15 25 78071
12
15 25
13
16 25
HM, LT, † 12 20 n 96939 Ø, @, CS, FS, HM, LT n 96944 Ø, @, CS, FS, HM, LT
13/16”, 7/8” 18, 21, 22mm, NO DRILL 13/16”, 7/8” 18, 21, 22mm, NO DRILL 13/16”, 7/8”
RD
78071
11 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
5
10 20
l 44577 Ø, CS, FS,
21, 22mm, 3/4”
NO DRILL
6
11 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25 78071
NO DRILL 5 3/4” 15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4”
7.5 20
n 44657 Ø,HM,SA
21, 22mm, 3/4”, 7/8”
1/2”
6
12 20 n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
21, 22mm, 3/4”, 7/8”
NO DRILL
JL, LT
6.5 40
HM, LT, †
13/16”, 7/8”
HM, LT 13/16”, 7/8” n 45022 Ø, #, CS, FS, 18, 21mm NO DRILL LT, TF
12
15 25
13
17 25
n 45293 Ø, #, CS, FS, 18, 21mm
18
18 25
13
16 25
21, 22mm, 3/4”, 7/8”
NO DRILL
5
10 20
l 44577 Ø, CS, FS,
21, 22mm, 3/4”
NO DRILL
6
11 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25 78071
l 51073 Ø, RT, CS, FS, 21, 22mm,
NO DRILL
5
7.5 20
n 44657 Ø,HM,SA
21, 22mm, 3/4”, 7/8”
1/2”
6
12 20 n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25
3/4”
JL, LT
HM, LT, †
13/16”, 7/8”
HM, LT 13/16”, 7/8” n 45022 Ø, #, CS, FS, LT, TF 18, 21mm NO DRILL n 45293 Ø, #, CS, FS, LT, TF 18, 21mm NO DRILL
n 96944 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL HM, LT
06996
–
7/16", 1/2" 35
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
13/16”, 7/8”
–
RD
–
85262
JL, LT
15, 18, 21mm, 9/16", 11/16", 3/4", T50
78071
16 25
15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50
n 51050 SA
n 88001 DB
–
13
13/16”, 7/8”
NO DRILL LT, TF n 96944 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL HM, LT 13/16”, 7/8”
03-06
BN,RD
85262
l 51073 Ø, RT, CS, FS, 21, 22mm,
Pickup, Silverado 3500 Series 8 ft. Bed, 2 & 4 WD
–
n 96944 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50
n 51050 SA
n 88001 DB
78071
–
HM, LT
Pickup, Silverado 2500 HD 03-06 8 ft. Bed, 2 & 4 WD
RD
85262
n 51050 SA
–
14 20 14 20
15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50
Pickup, Silverado 1500 LD 03-05 8 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Silverado 2500 HD 03-06 6.6 ft. Bed, 2 & 4 WD
n 88001 DB
12 12
BN,RD
BN,RD
–
RD
–
BN,RD
–
13 17 25 18 18 25 13 16 25 85262
RD
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 88001 DB,RO
NO DRILL
JL,RO, † 7.5 15 n 96932 Ø,@,HM, JL,RO
–
OEM REPLACE.
l 44563 Ø,JL,RO
78071
FOOTNOTES
10.5 15
STANDARD WIRE
6
15
T-CONNECTOR
21, 22mm, NO DRILL 3/4” 9/16”, 3/4” 1/2”
WT. DISTRIB. INSTALL TIME
l 51081 Ø,RT,JL,RO
WT. CARRYING
8
DRILL BITS
6
WRENCHES
21mm, 3/4”, NO DRILL 7/8”
FOOTNOTES
l 33093 Ø,JL
HITCH NUMBER
STYLE
7.5 15
DRILL BITS
WT. CARRYING WT. DISTRIB. INSTALL TIME 5
WRENCHES
DRILL BITS NO DRILL
FOOTNOTES
WRENCHES 21mm, 3/4”,7/8”
HITCH NUMBER
l 51072 Ø,RT,JL,RO
l 37069 Ø,RO
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
FOOTNOTES
03-05
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Pickup, Silverado 1500 LD 6.6 ft. Bed, 2 & 4 WD
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
105
CHEVROLET
CHEVROLET
104
REESE TOWPOWER
REESE TOWPOWER
6
10.5 15
l 44563 Ø,JL
NO DRILL
6
10.5 15 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL
12
14 20
5
7.5 25
n 44619 Ø,CM
NO DRILL
6
7.5 15
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4”
6.5 35
n 37016 Ø
21, 22mm, 3/4” 21, 22mm, 3/4” 21mm, 3/4”
NO DRILL
7.5 12 20
7.5 15
l 37034 Ø,RO l 37094 Ø,RO l 44564 Ø,JL
n 37096 Ø,JL,RO
l 51072 Ø,JL
Pickup, Silverado 1500 LD 8 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan
APPLICATIONS GUIDE
–
6
8
NO DRILL
12
14 20 78071
l 51081 Ø,RT,JL
21, 22mm, NO DRILL 3/4” 9/16”, 3/4” 1/2”
6
10.5 15
l 44563 Ø,JL
6
10.5 15 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL
12
14 20
5
7.5 25 6.5 35
l 37034 Ø l 37094 Ø
21, 22mm, NO DRILL 3/4” 15/16", 3/4” 5/8”
7 7
12 25 12 25
7.5 15
l 44564 Ø,JL
6
8
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21mm, NO DRILL 5 3/4”,7/8”
l 51072 Ø,RT,JL
21mm, 3/4”,7/8”
l 37069 Ø n 37096 Ø,JL,RO
9/16”, 3/4” 1/2”
15/16", 3/4” 5/8” 21mm, 3/4”, NO DRILL 7/8”
15 n 41932 Ø,@,
HM,JL, †
21mm, 7/8”
NO DRILL
5
7.5 15
l 33093 Ø,JL
5
7.5 25 6.5 35
l 37034 Ø l 37094 Ø,RO
7.5 15
l 44564 Ø,JL
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21mm, NO DRILL 5 3/4”,7/8”
85217
(with amber bulbs)
85262
RD
15
15 n 41932 Ø,@,
78071
–
BN,RD
–
–
BN,RD
–
–
(with amber – bulbs)
21mm, 3/4”, NO DRILL 7/8”
6
8
NO DRILL
12
14 20 78071
15/16", 3/4” 5/8”
7 7
12 25 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL 12 25
12
14 20
6
8
15/16", 3/4” 5/8” 21mm, 3/4”, NO DRILL 7/8”
HM,JL, †
21mm, 7/8”
85217
15 85262 –
BN,RD
–
–
BN,RD
–
21mm, 3/4”,7/8”
NO DRILL
5
7.5 15
l 33093 Ø,JL
21mm, 3/4”, NO DRILL 7/8”
6
8
15 n 41932 Ø,@,HM,
21mm, 7/8”
NO DRILL
12
14 20 78071
l 51081 Ø,RT,JL,RO
21, 22mm, 3/4” NO DRILL
6
10.5 15
l 44563 Ø,JL,RO
21, 22mm, 3/4” NO DRILL
6
10.5 15 n 96932 Ø,@,HM,
21mm, 7/8”
NO DRILL
12
14 20
n 37096 Ø,JL,RO
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 9/16”, 3/4” 1/2” 5
6.5 35
l 37034 Ø,RO
15/16", 3/4” 5/8”
7
12 25
7.5 25 7.5 15
l 37094 Ø,RO l 44564 Ø,JL,RO
15/16", 3/4” 5/8”
7 6
12 25 8 15
21mm, 3/4”,7/8”
NO DRILL
5
21mm, 3/4”, NO DRILL 7/8”
JL,RO, †
JL,RO
85262 –
BN,RD
–
–
BN,RD
–
21mm, 3/4”,7/8”
NO DRILL
5
7.5 15
l 33093 Ø,JL
21mm, 3/4”, NO DRILL 7/8”
6
8
NO DRILL
12
14 20 78071
l 51081 Ø,RT,JL
21, 22mm, NO DRILL 3/4” 9/16”, 3/4” 1/2”
6
10.5 15
l 44563 Ø,JL
6
10.5 15 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL
12
14 20
5
7.5 25 6.5 35
l 37034 Ø,RO l 37094 Ø,RO
21, 22mm, NO DRILL 3/4” 15/16", 3/4” 5/8”
7 7
12 25 12 25
7.5 15
l 44564 Ø,JL
6
8
7/16", 1/2" 35
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21mm, NO DRILL 5 3/4”,7/8”
15/16", 3/4” 5/8” 21mm, 3/4”, NO DRILL 7/8”
15 n 41932 Ø,@,
HM,JL, †
21mm, 7/8”
15 85262 78071
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
RD
78071 l 51072 Ø,RT,JL
2006 06996
RD
78071 l 51072 Ø,RT,JL,RO
l 51072 Ø,RT,JL 15, 18, 21mm, 9/16", 11/16", 3/4", T50
BN,RD
21mm, 3/4”, NO DRILL 7/8”
l 37069 Ø n 37096 Ø,JL,RO
n 88001 DB,RO
–
l 33093 Ø,JL
7/16", 1/2" 35
Pickup, Silverado 1500 LD 2006 6.6 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Silverado 1500 LD 2006 8 ft. Bed, 2 & 4 WD
–
RD
–
BN,RD
–
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
15, 18, 21mm, 9/16", 11/16", 3/4", T50
BN,RD
7.5 15
l 37069 Ø,RO l 51072 Ø,RT,JL n 88001 DB,RO
–
5
7/16", 1/2" 35
Pickup, Silverado 1500 LD 2006 5.8 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Silverado 1500 LD 2006 6.6 ft. Bed, 2 & 4 WD
78071 NO DRILL
l 51072 Ø,RT,JL 15, 18, 21mm, 9/16", 11/16", 3/4", T50
21mm, 3/4”, NO DRILL 7/8”
–
12 25 12 25 8 15
7/16", 1/2" 35
Pickup, Silverado 1500 HD 2006 6.6 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Silverado 1500 LD 2006 5.8 ft. Bed, 2 & 4 WD
n 88001 DB,RO
5
BN,RD
21mm, 3/4”,7/8”
l 51072 Ø,RT,JL 15, 18, 21mm, 9/16", 11/16", 3/4", T50
NO DRILL
7 7 6
–
l 51072 Ø,RT,JL
l 37069 Ø n 37096 Ø,JL,RO
n 88001 DB
21mm, 3/4”,7/8”
15/16", 3/4” 5/8” 15/16", 3/4” 5/8”
OEM REPLACE.
21, 22mm, NO DRILL 3/4” 9/16”, 3/4” 1/2”
FOOTNOTES
l 51081 Ø,RT,JL
STANDARD WIRE
WT. DISTRIB. INSTALL TIME
14 20 78071
T-CONNECTOR
WT. CARRYING 12
DRILL BITS
15 n 41932 Ø,@, HM,JL, † 21mm, 7/8” NO DRILL
WRENCHES
8
FOOTNOTES
6
HITCH NUMBER
21mm, 3/4”, NO DRILL 7/8”
DRILL BITS
l 33093 Ø,JL
WRENCHES
STYLE
7.5 15
FOOTNOTES
WT. CARRYING WT. DISTRIB. INSTALL TIME 5
HITCH NUMBER
DRILL BITS NO DRILL
FOOTNOTES
21mm, 3/4”,7/8”
HITCH NUMBER
l 51072 Ø,RT,JL
l 37069 Ø
Pickup, Silverado 1500 LD 04-05 5.8 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Silverado 1500 HD 2006 6.6 ft. Bed, 2 & 4 WD
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
WRENCHES
Pickup, Silverado 1500 LD 04-05 5.8 ft. Bed, 2 & 4 WD
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
107
CHEVROLET
CHEVROLET
106
REESE TOWPOWER
REESE TOWPOWER
10.5 15
7.5 25 6.5 35
l 37034 Ø l 37094 Ø,RO
7 7
12 25 12 25 n 41932 Ø,@,
7.5 15
l 44564 Ø,JL
6
8
HITCH NUMBER
l 51072 Ø,RT,JL n 88001 DB,RO
1/4”, 1/2”, 5 9/16” NO DRILL
5
15 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL
12
14 20
RD
85262
–
(with amber – bulbs)
l 51081 Ø,RT,JL
21, 22mm, NO DRILL 3/4” 9/16”, 3/4” 1/2”
6
10.5 15
l 44563 Ø,JL
6
10.5 15
5 5
7.5 25 7.5 15
l 37034 Ø l 37094 Ø,RO
21, 22mm, NO DRILL 3/4” 15/16", 3/4” 5/8”
7 7
12 25 12 25 n 41932 Ø,@,
NO DRILL
12
14 20 85217
6
8
NO DRILL
12
14 20
NO DRILL
15/16", 3/4” 5/8” 21mm, 3/4”, NO DRILL 7/8”
21mm, 7/8” HM,JL, † 15 n 96932 Ø,@, HM,JL 21mm, 7/8”
85262 74682
–
RD
85262
74682
–
RD
85262
–
(with amber bulbs)
–
l 51072 Ø,RT,JL,RO
21mm, 3/4”,7/8”
NO DRILL
5
7.5 15
l 33093 Ø,JL
21mm, 3/4”, NO DRILL 7/8”
6
8
l 51081 Ø,RT,JL,RO
21, 22mm, NO DRILL 3/4” 9/16”, 3/4” 1/2”
6
10.5 15
l 44563 Ø,JL,RO
6
10.5 15
5
7.5 25
l 37034 Ø,RO
21, 22mm, NO DRILL 3/4” 15/16", 3/4” 5/8”
7
12 25
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21mm, NO DRILL 5 3/4”,7/8”
6.5 35
l 37094 Ø,RO
15/16", 3/4” 5/8”
7
12 25 n 41932 Ø,@,HM,
21mm, 7/8”
NO DRILL
12
14 20 85217
7.5 15
l 44564 Ø,JL,RO
21mm, 3/4”, NO DRILL 7/8”
6
8
15 n 96932 Ø,@,HM,
21mm, 7/8”
NO DRILL
12
14 20
15
JL,RO, †
JL,RO
RD
85262 74682
–
RD
85262
–
RD
85262
l 51072 Ø,RT,JL
21mm, 3/4”,7/8”
NO DRILL
5
7.5 15
l 33093 Ø,JL
21mm, 3/4”, NO DRILL 7/8”
6
8
NO DRILL
12
14 20 74682
l 51081 Ø,RT,JL
21, 22mm, NO DRILL 3/4” 9/16”, 3/4” 1/2”
6
10.5 15
l 44563 Ø,JL
6
10.5 15 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL
12
14 20
5
7.5 25 6.5 35
l 37034 Ø,RO l 37094 Ø,RO
21, 22mm, NO DRILL 3/4” 15/16", 3/4” 5/8”
7 7
12 25 12 25
7.5 15
l 44564 Ø,JL
6
8
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21mm, NO DRILL 5 3/4”,7/8”
15/16", 3/4” 5/8” 21mm, 3/4”, NO DRILL 7/8”
15 n 41932 Ø,@,
HM,JL, †
21mm, 7/8”
RD
15
15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50
85262 74682
–
RD
85262
–
RD
85262
l 51073 Ø, RT, CS, FS, 21, 22mm,
NO DRILL
5
7.5 20
l 44577 Ø, CS, FS,
21, 22mm, 3/4”
NO DRILL
6
11 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25 74682
n 51050 SA
NO DRILL
5
10 20
n 44657 HM,SA
21, 22mm, 3/4”, 7/8”
1/2”
6
12 20 n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
1/4”, 1/2”, 5 9/16”
6.5 40
JL, LT
n 37096 Ø,JL
3/4”
21, 22mm, 3/4”, 7/8” 15,17,18, 19,21, 22mm, 9/16”,3/4”
JL, LT
HM, LT, †
HM, LT 13/16”, 7/8” n 45022 Ø, #, CS, FS, 18, 21mm NO DRILL LT, TF
12
15 25
13
17 25
n 96944 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
13
16 25
HM, LT
7/16", 1/2" 35
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
13/16”, 7/8”
13/16”, 7/8”
RD
85262
RD
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
–
8
l 51072 Ø,RT,JL
06996
74682
6
15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50
15, 18, 21mm, 9/16", 11/16", 3/4", T50
85262
21mm, 3/4”, NO DRILL 7/8”
l 37069 Ø n 37096 Ø,JL,RO
n 88001 DB
BN,RD
l 33093 Ø,JL
21mm, 3/4”,7/8”
RD
–
7.5 15
15
85262
74682 5
l 51072 Ø,RT,JL
Pickup, Silverado 1500 LD 2007 8 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan (Classic) Pickup, Silverado 2500 HD 2007 6.6 ft. Bed, 2 & 4 WD (Classic)
(with amber – bulbs)
14 20 85217
NO DRILL
n 37096 Ø,JL,RO
n 88001 DB,RO
–
12
21mm, 7/8”
21mm, 3/4”,7/8”
l 37069 Ø,RO
Pickup, Silverado 1500 LD 2007 6.6 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan (Classic) Pickup, Silverado 1500 LD 2007 8 ft. Bed, 2 & 4 WD (Classic)
BN,RD
NO DRILL
HM,JL, †
15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50
Pickup, Silverado 1500 LD 2007 5.8 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan (Classic) Pickup, Silverado 1500 LD 2007 6.6 ft. Bed, 2 & 4 WD (Classic)
–
l 51072 Ø,RT,JL
l 44564 Ø,JL
n 88001 DB,RO
21mm, 3/4”, NO DRILL 7/8”
74682
85262
l 37069 Ø l 51072 Ø,RT,JL
n 88001 DB,RO
15/16", 3/4” 5/8”
15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50
Pickup, Silverado 1500 HD 2007 6.6 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan (Classic) Pickup, Silverado 1500 LD 2007 5.8 ft. Bed, 2 & 4 WD (Classic)
APPLICATIONS GUIDE
15,17,18, 19,21, 22mm, 9/16”,3/4” 21mm, 3/4”,7/8”
OEM REPLACE.
6
5
21, 22mm, NO DRILL 3/4” 15/16", 3/4” 5/8”
FOOTNOTES
l 44563 Ø,JL
STANDARD WIRE
10.5 15
15
T-CONNECTOR
6
WT. DISTRIB. INSTALL TIME
21, 22mm, NO DRILL 3/4” 9/16”, 3/4” 1/2”
WT. CARRYING
l 51081 Ø,RT,JL
DRILL BITS
8
WRENCHES
6
FOOTNOTES
21mm, 3/4”, NO DRILL 7/8”
HITCH NUMBER
l 33093 Ø,JL
DRILL BITS
7.5 15
WRENCHES
STYLE
5
FOOTNOTES
WT. CARRYING WT. DISTRIB. INSTALL TIME
NO DRILL
HITCH NUMBER
DRILL BITS
21mm, 3/4”,7/8”
FOOTNOTES
l 51072 Ø,RT,JL
l 37069 Ø n 37096 Ø,JL,RO
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
WRENCHES
2007
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Pickup, Silverado 1500 HD 6.6 ft. Bed, 2 & 4 WD (Classic)
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
109
CHEVROLET
CHEVROLET
108
REESE TOWPOWER
REESE TOWPOWER
n 44657 Ø,HM,SA
21, 22mm, 3/4”, 7/8”
1/2”
6
12 20 n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
6.5 40
HM, LT 13/16”, 7/8” n 45022 Ø, #, CS, FS, 18, 21mm NO DRILL LT, TF
12
15 25
13
17 25
n 45293 Ø, #, CS, FS, 18, 21mm
18
18 25
13
16 25
NO DRILL LT, TF n 96944 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL HM, LT 13/16”, 7/8”
n 88001 DB Pickup, Silverado 3500 Series 8 ft. Bed, 2 & 4 WD (Classic)
15, 18, 21mm, 9/16", 11/16", 3/4", T50
7/16", 1/2" 35
85262 n 51050 SA
2007
21, 22mm, 3/4”, 7/8”
NO DRILL
5
10 20
l 44577 Ø, CS, FS,
21, 22mm, 3/4”
NO DRILL
6
11 20 n 41939 Ø, @, CS,
18, 21, 22mm, NO DRILL 13/16”, 7/8”
12
15 25 74682
l 51073 Ø, RT, CS, FS, 21, 22mm,
NO DRILL
5
7.5 20
n 44657 Ø,HM,SA
21, 22mm, 3/4”, 7/8”
1/2”
6
12 20 n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
n 88001 DB
15, 18, 21mm, 9/16", 11/16", 3/4", T50
3/4”
FS, LT, †
HM, LT n 45022 Ø, #, CS, FS, LT, TF n 45293 Ø, #, CS, FS, LT, TF n 96944 Ø, @, CS, FS, HM, LT
JL, LT
l 51073 Ø, RT, CS, FS, 21, 22mm, JL, LT
3/4”
NO DRILL
5
l 44577 Ø, CS, FS, JL, LT
l 51073 Ø, RT, CS, FS, 21, 22mm, JL, LT
3/4”
NO DRILL
5
21, 22mm, 3/4”
NO DRILL
6
7.5 20
Pickup, Silverado 2500 HD 07-10 8 ft. Bed, 2 & 4 WD (New Body Style)
17 25
18, 21mm
NO DRILL
18
18 25
18, 21, 22mm, NO DRILL 13/16”, 7/8”
13
16 25
21, 22mm, 3/4”
NO DRILL
6
12
15 25 74682
n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25 85262
13
17 25
18, 21, 22mm, NO DRILL 13/16”, 7/8” 18, 21, 22mm, NO DRILL 13/16”, 7/8”
13
16 25
12
15 25 74682
n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25 85262
n 45022
13/16”, 7/8” 18, 21mm NO DRILL
13
17 25
18, 21mm
NO DRILL
18
18 25
18, 21, 22mm, NO DRILL 13/16”, 7/8” 18, 21, 22mm, NO DRILL 13/16”, 7/8”
13
16 25
12
15 25 74682
11 20 n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25 85262
13
17 25
18, 21, 22mm, NO DRILL 13/16”, 7/8” 18, 21, 22mm, NO DRILL 13/16”, 7/8”
13
16 25
12
15 25 74682
n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
HM, LT, †
HM, LT n 45022 Ø, #, CS, FS, LT, TF n 96944 Ø, @, CS, FS, HM, LT 11 20 n 41939 Ø, @, CS, FS, HM, LT, †
7.5 20
n 96944 Pickup, Silverado 3500 HD 07-10 6.6 ft. Bed, 2 & 4 WD (New Body Style)
n 41939 l 51073 Ø, RT, CS, FS, 21, 22mm, JL, LT
3/4”
l 51073 Ø, RT, CS, FS, 21, 22mm, JL, LT
3/4”
NO DRILL
NO DRILL
5
5
7.5 20
7.5 20
l 44577 Ø, CS, FS, JL, LT
l 44577 Ø, CS, FS, JL, LT
21, 22mm, 3/4”
21, 22mm, 3/4”
NO DRILL
NO DRILL
6
6
HM, LT Ø, #, CS, FS, LT, TF Ø, #, CS, FS, LT, TF Ø, @, CS, FS, HM, LT Ø, @, CS, FS, LT, †
HM, LT n 45022 Ø, #, CS, FS, LT, TF n 96944 Ø, @, CS, FS, HM, LT 11 20 n 41939 Ø, @, CS, FS, LT, † HM, LT n 45022 Ø, #, CS, FS, LT, TF n 45293 Ø, #, CS, FS, LT, TF n 96944 Ø, @, CS, FS, HM, LT
l 51072 Ø,RT,JL l 51081 Ø,RT,JL l 51072 Ø,RT,JL l 51072 Ø,RT,JL l 51081 Ø,RT,JL l 51072 Ø,RT,JL 06996
13
11 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
n 45293
Pickup, Silverado 1500 LD 07-13 6.6 ft. Bed, 2 & 4 WD (New Body Style)
15 25
RD
–
85262 l 44577 Ø, CS, FS,
Pickup, Silverado 1500 LD 07-13 5.8 ft. Bed, 2 & 4 WD (New Body Style)
12
7/16", 1/2" 35
Pickup, Silverado 2500 HD 07-10 6.6 ft. Bed, 2 & 4 WD (New Body Style)
Pickup, Silverado 3500 HD 07-10 8 ft. Bed, 2 & 4 WD (New Body Style)
13/16”, 7/8” 18, 21mm NO DRILL
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
NO DRILL
5
7.5 15
l 33093 Ø,JL
21, 22mm, 3/4” NO DRILL NO DRILL
6 5
10.5 15 7.5 15
l 44563 Ø,JL l 44564 Ø,JL
NO DRILL
5
7.5 15
l 33093 Ø,JL
21, 22mm, 3/4” NO DRILL
6 5
10.5 15 7.5 15
l 44563 Ø,JL l 44564 Ø,JL
21mm, 3/4”,7/8” 21mm, 3/4”,7/8” 21mm, 3/4”,7/8” 21mm, 3/4”,7/8”
NO DRILL
NO DRILL
6
8
21, 22mm, 3/4” NO DRILL NO DRILL
6 6
10.5 15 8 15
NO DRILL
6
8
21, 22mm, 3/4” NO DRILL
6 6
10.5 15 8 15
21mm, 3/4”, 7/8” 21mm, 3/4”, 7/8” 21mm, 3/4”, 7/8”
21mm, 3/4”, NO DRILL 7/8”
15
15
13/16”, 7/8”
13/16”, 7/8” 18, 21mm NO DRILL
13/16”, 7/8” 18, 21mm NO DRILL
13/16”, 7/8” 18, 21mm NO DRILL
12
15 25 85262
13
17 25
18, 21mm
NO DRILL
18
18 25
18, 21, 22mm, NO DRILL 13/16”, 7/8”
13
16 25
85262
RD
85262
RD
–
BN,RD
85262
BN
–
BN,RD
85262
BN
–
BN,RD
85262
BN
–
BN,RD
85262
BN
74682
–
BN,RD
85262
74682
–
BN,RD
85262
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
JL, LT
JL, LT
RD
OEM REPLACE.
7.5 20
–
FOOTNOTES
NO DRILL 5 3/4” 15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4”
STANDARD WIRE
WT. DISTRIB. INSTALL TIME
15 25 74682
13/16”, 7/8”
T-CONNECTOR
WT. CARRYING 12
HM, LT, †
DRILL BITS
11 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
WRENCHES
6
FOOTNOTES
WRENCHES
NO DRILL
HITCH NUMBER
FOOTNOTES
21, 22mm, 3/4”
JL, LT
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
STYLE
l 44577 Ø, CS, FS,
NO DRILL
DRILL BITS
WT. CARRYING WT. DISTRIB. INSTALL TIME 10 20
21, 22mm, 3/4”, 7/8”
l 51073 Ø, RT, CS, FS, 21, 22mm,
JL, LT n 37096 Ø,JL
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
5
DRILL BITS
FOOTNOTES
HITCH NUMBER
n 51050 SA
WRENCHES
Pickup, Silverado 2500 HD 2007 8 ft. Bed, 2 & 4 WD (Classic)
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
111
CHEVROLET
CHEVROLET
110
REESE TOWPOWER
REESE TOWPOWER
Pickup, Silverado 2500 HD 11-12 6.6 ft. Bed, 2 & 4 WD (New Body Style)
6
11 15
Pickup, Silverado 2500 HD 11-12 8 ft. Bed, 2 & 4 WD (New Body Style)
HITCH NUMBER
6
10.5 15
6
8
8
12 20 n 41942 Ø, @, CS, FS, 13, 21, 22mm, NO DRILL n 96942 Ø, @, CS, FS, 13, 21, 22mm, NO DRILL
n 44563 Ø, CS, FS, GP, 13, 21, 22mm, NO DRILL JL, LT
3/4”, 7/8”
8
–
BN,RD
85262
15
16 20 74682
–
BN,RD
85262
15
16 20 85262
–
BN
–
18
18 60
15
16 20 74682
–
BN,RD
85262
15
16 20 85262
–
BN
–
18
18 30
15
16 20 74682
–
BN,RD
85262
15
16 20 85262
–
BN
–
18
18 60
15
16 20 74682
–
BN,RD
85262
n 96942 Ø, @, CS, FS, 13, 21, 22mm, NO DRILL
15
16 20 85262
–
BN
–
n 45300
18 20 –
–
–
–
15 GP, JL, LT, †
GP, JL, LT n 45300 #, CS, FS, HM, JL, KH, LT 12 20 n 41942 Ø, @, CS, FS, GP, JL, LT, †
3/4”, 7/8”
3/4”, 7/8” 13, 19, 21, 3/8”, 9/16” 22mm, 3/4”, hole saw 7/8” 13, 21, 22mm, NO DRILL 3/4”, 7/8”
APPLICATIONS GUIDE
l 51197 Ø, CS, FS, HM, 21, 22mm, JL, LT
3/4”, 7/8”
NO DRILL
6
11 15
n 44563 Ø, CS, FS, GP, 13, 21, 22mm, NO DRILL JL, LT
3/4”, 7/8”
8
GP, JL, LT 3/4”, 7/8” n 45300 Ø, #, CS, FS, 13, 19, 21, 3/8”, 9/16” HM, JL, LT 22mm, 3/4”, hole saw 7/8” 12 20 n 41942 Ø, @, CS, FS, 13, 21, 22mm, NO DRILL GP, JL, LT 3/4”, 7/8”, †
n 96942 Ø, @, CS, FS, 13, 21, 22mm, NO DRILL
Pickup, Silverado 3500 HD 11-12 8 ft. Bed, 2 & 4 WD (New Body Style)
n 44563 Ø, CS, FS, GP, 13, 21, 22mm, NO DRILL JL, LT
3/4”, 7/8”
8
GP, JL, LT n 45300 #, CS, FS, HM, JL, KH, LT 12 20 n 41942 Ø, @, CS, FS, GP, JL, LT, † GP, JL, LT
Pickup, Silverado, Cab & Chassis 01-07 3500 Series w/34 Wide Frames (Classic)
Ø, #, CS, FS, HM, JL, LT
n 41936 @, † n n n n
96936 41938 96938 41940
n 77005 –
10, 17, 18mm, 11/16” 1” hole saw
30 n n n n n
88002 88002 88002 88002 06958
–
3/4”
1/2”
–
3/4”
1/2”
–
3/4”
1/2”
–
3/4”
1/2”
Ø,GU,HM,RH 18mm, 3/4”, 7/8” –
30 30 30 30 35 n 37152 CN,GU,SB n 37042 CN,GU,SB
n 88001 CN,GU,SB 06996
15, 18, 21mm, 9/16", 11/16", 3/4", T50
7/16", 1/2" 40
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
n 33014 Ø n 33014 Ø n 33014 Ø 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
30
1/4”, 1/2”, 5 9/16”
6
30
n 33053 Ø,GU
18mm
NO DRILL
18mm
NO DRILL
18mm
NO DRILL
18mm, 3/4”, NO DRILL 7/8”
12
17/32”
30 15 40 – 15 40 – 16 35
– –
–
– –
9/16”
12 12 12 15
9/16”
15
16 35 –
–
–
–
11/16”
15
16 35 –
17/32”
12
17/32”
12 12 12 15
30 15 40 15 40 – 16 35
15
16 35 –
15
16 35 –
@,CC
13/16”, 7/8” 9/16”
@
21mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21, 24mm, 13/16”, 7/8” 3/4”
@
3/4”
@,CC, †
13/16”, 7/8” 9/16”
@,CC
13/16”, 7/8” 9/16”
@, †
21mm, 9/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8” 21, 24mm, 11/16” 13/16”, 7/8”
n 96947 @ 98-02 1983 84-91 84-91 92-94 83-84
17/32”
13/16”, 7/8” 9/16”
n 96940 @
Prizm S-10 Blazer Downsize, All Models S-10 Blazer Downsize, 2 Dr. S-10 Blazer Downsize, 4 Dr. S-10 Blazer Downsize, All Models S-10 Pickup w/Standard Box & Step Bumper
18
3/4”
n 41936 @, † 96936 41938 96938 41940
3/8”, 9/16” hole saw
@
n 96947 @
n n n n
3/4”, 7/8” 13, 19, 21, 22mm, 3/4”, 7/8” 3/4”
@,CC, †
n 96940 @
Pickup, Silverado, Cab & Chassis 07-13 3500 HD w/34 Wide Frames (New Body Style)
3/4”, 7/8” 13, 19, 21, 3/8”, 9/16” 22mm, 3/4”, hole saw 7/8” 13, 21, 22mm, NO DRILL 3/4”, 7/8”
30 74682
30 74682
–
–
BN,RD
85262
–
–
–
–
–
–
–
3.5 6 3.5 6 3.5 6
60 60 60
– – 74427 –
78013 78058 78058 78058
–
– – – –
3.5 6
45
–
–
–
–
– – BN
74051
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
74682
n 96942 Ø, @, CS, FS, 13, 21, 22mm, NO DRILL
Pickup, Silverado 3500 HD 11-12 6.6 ft. Bed, 2 & 4 WD (New Body Style)
OEM REPLACE.
NO DRILL
21, 22mm, NO DRILL 3/4” 21mm, 3/4”, NO DRILL l 44564 Ø,JL 7/8” n 44563 Ø, CS, FS, GP, 13, 21, 22mm, NO DRILL JL, LT 3/4”, 7/8”
FOOTNOTES
7.5 15
15
STANDARD WIRE
5
8
T-CONNECTOR
NO DRILL
6
WT. DISTRIB. INSTALL TIME
l 44563 Ø,JL
21mm, 3/4”, NO DRILL 7/8”
WT. CARRYING
10.5 15
DRILL BITS
6
WRENCHES
NO DRILL
FOOTNOTES
21, 22mm, 3/4” 21mm, l 51072 Ø,RT,JL 3/4”,7/8” l 51197 Ø, CS, FS, HM, 21, 22mm, JL, LT 3/4”, 7/8”
l 51081 Ø,RT,JL
HITCH NUMBER
l 33093 Ø,JL
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
STYLE
7.5 15
DRILL BITS
WT. CARRYING WT. DISTRIB. INSTALL TIME 5
l 51072 Ø,RT,JL
FOOTNOTES
DRILL BITS NO DRILL
FOOTNOTES
21mm, 3/4”,7/8”
HITCH NUMBER
WRENCHES
Pickup, Silverado 1500 LD 07-13 8 ft. Bed, 2 & 4 WD (New Body Style)
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
WRENCHES
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
113
CHEVROLET
CHEVROLET
112
REESE TOWPOWER
REESE TOWPOWER
n 06958 Ø,GU,HM,RH 18mm, 3/4”, 7/8” –
35 n 37152 CN,GU,SB n 37042 CN,GU,SB
30
1/4”, 1/2”, 5 9/16”
6
30
OEM REPLACE.
FOOTNOTES
STANDARD WIRE
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
3.5 6
40
–
–
–
–
n 33053 Ø,GU
18mm, 3/4”, NO DRILL 7/8”
3.5 6
45
74178
78058
–
–
74178 n 33055 Ø,†
13, 18, 19mm, NO DRILL 3/4”, 7/8”
3.5 6
40
74178
78058
–
–
96-97
n 33055 Ø
13, 18, 19mm, NO DRILL 3/4”, 7/8”
3.5 6
40
74178
78058
–
–
–
–
–
–
n 51063 CN,GP,GU
98-04
3/4”
1/2”
3.5 5 20
98-04
n 33055 Ø
13, 18, 19mm, NO DRILL 3/4”, 7/8”
3.5 6
40
–
–
–
–
98-04
n 44062 Ø
3/4”
NO DRILL
3.5 6
40
–
–
–
–
n 44062 CN,GU
3/4”
NO DRILL
3.5 5
20
74216
78058
–
–
–
–
–
–
74180
78058
BN
–
74682, 78058 85262
RD
85262
n 06958 Ø,GU,RH
98-04
2012 2012 2013 2013 92-99
n n n n
77251 77265 77281 77282
Ø,GP
13mm, 3/4”
11/16”
Ø,HM,JR
11/16”
–
GP,JR
11/16”, 7/8”
1/2”
GP,JR
11/16”, 7/8”
1/2”
18mm, 3/4”, 7/8” –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
35 n 37152 AF, CN, GU, ST 15,17,18, 19,21, 1/4”, 1/2”, 5 22mm,T-50, 9/16” 9/16”,3/4” n 37042 AF, CN, GU, ST 15,17,18, 19,21, 1/4”, 1/2”, 5 22mm,T-50, 9/16” 9/16”,3/4”
6
30
6
30
7/16", 1/2" 40
74216
20 20 25 25 n 37152 –
n 51012 HM n 51012 HM n 88001 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
1/4”, 1/2”, 5 9/16”
6
30
n 37074 HM
7/8”
1/2”, 9/16” 6
10 30
1/4”, 1/2”, 5 9/16”
6
30
n 44656 HM
7/8”
1/2”, 9/16” 5
7.5 30
1/2”, 9/16” 5
7 30 7 30
n 44096 HM
7/8”
1/2”, 9/16” 5
7
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 7/8” 7/8”
1/2”, 9/16” 5
30
7/16", 1/2" 30
74180 n 37152 –
00-02
n 37042 – n 51201 Ø,CN,HM
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 22mm, 7/8”
1/4”, 1/2”, 5 9/16”
6
30
1/4”, 1/2”, 5 9/16”
6
30
NO DRILL
5
10 15
n 37072 Ø,CN,HM
22mm, 7/8”
NO DRILL
6
10 20
l 44668 Ø,CN,HM
22mm, 7/8”
NO DRILL
6
10 15 n 41930 @,CN, †
n 44095 Ø,CN,HM
22mm, 7/8”
NO DRILL
5
10 20 n 96930 @,CN n 45013 #,TF
n 88001 – Suburban New Body Style w/Amber Turn Signals
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
6
13, 18, 19mm, NO DRILL 3/4”, 7/8”
7/16", 1/2" 40
n 37042 –
Suburban New Body Style w/Amber Turn Signals
1/4”, 1/2”, 5 9/16”
n 33055 Ø
94-97
n 88001 CN,GU,ST Sonic, 4 Dr. Sedan, All Models Sonic, 5 Dr. Hatchback, All Models Spark, Models w/o Ground Effects Spark, Models w/Ground Effects Suburban Old Body Style
15, 18, 21mm, 9/16", 11/16", 3/4", T50
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
15, 18, 21mm, 9/16", 11/16", 3/4", T50
n 37042 – n 51201 Ø,CN,HM
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 22mm, 7/8”
–
BN
–
10
12 35 85262
–
BN
–
12
14 50
RD
85262
1/4”, 1/2”, 5 9/16”
6
30
n 37072 Ø,CN,HM
22mm, 7/8”
NO DRILL
6
10 20
1/4”, 1/2”, 5 9/16”
6
30
l 44668 Ø,CN,HM
22mm, 7/8”
NO DRILL
6
10 15 n 41930 @,CN, †
22mm, 13/16”, 1/2” 7/8”, 3/4”
10
12 35 85262
–
BN
–
10 15
n 44095 Ø,CN,HM
22mm, 7/8”
NO DRILL
5
10 20 n 96930 @,CN
22mm, 13/16”, 1/2” 7/8”, 3/4” 21mm, 3/4” 1/2”
10
12 35 85262
–
BN
–
12
14 50
NO DRILL
5
74682, 78058 85262
n 45013 #,TF
06996
12 35 85262
85262 n 37152 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
10
7/16", 1/2" 30
03-06
n 88001 –
22mm, 13/16”, 1/2” 7/8”, 3/4” 22mm, 13/16”, 1/2” 7/8”, 3/4” 21mm, 3/4” 1/2”
7/16", 1/2" 30
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
85262
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 88001 CN,GU,SB S-10 Pickup w/Rear Fascia & No Step Bumper S-10 Pickup w/Sportside Box & Non-Towing Bumper S-10 Pickup All, Except Sportside Box w/Non-Towing Bumper & Standard Box w/ Rear Fascia S-10 Pickup w/Rear Fascia & No Step Bumper S-10 Pickup w/Sportside Box & Non-Towing Bumper S-10 Pickup w/Standard Box & Step Bumper, Inc. ZR2, Highlander Pkg. & Crew Cab
WRENCHES
FOOTNOTES
HITCH NUMBER
85-93 85-97
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
S-10 Pickup w/Rear Fascia & No Step Bumper S-10 Pickup w/Standard Box & Step Bumper, Inc. ZR2 & Highlander Pkg.
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
115
CHEVROLET
CHEVROLET
114
REESE TOWPOWER
REESE TOWPOWER
n 88001 –
n 51201 Ø,CN,HM
n 37042 – n 51201 Ø,CN,HM
14mm, 18, 19mm 1/2” 19mm
NO DRILL
TrailBlazer
1/2”, 9/16” 5
7 30 7 30
n 44656 HM
7/8”
1/2”, 9/16” 5
7.5 30
7/8”
1/2”, 9/16” 5
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 22mm, 7/8”
1/4”, 1/2”, 5 9/16”
6
30
1/4”, 1/2”, 5 9/16”
6
30
NO DRILL
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 22mm, 7/8”
n 06302 AL,GP,JR n 51102 AL,GP,JR
Van, G-Series Full Size Van, G-Series Full Size
5
6
30
1/4”, 1/2”, 5 9/16”
6
30
NO DRILL
14mm, 18mm
NO DRILL
15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50 18mm, 7/8” NO DRILL 15 n 51031 Ø, FP, HM, KK 18mm, NO DRILL 1-1/8” l 37051 FP,JT,KK 18mm, 3/4” 1/2”
10, 15mm, 3/4”, 7/8” 10, 15mm, 3/4”, 7/8” 10, 15mm, 3/4”, 7/8” 10, 15mm, 3/4”, 7/8”
5
10 15
1-1/8” 18mm, 3/4” NO DRILL
3.5
15
97-05
n 77040 AL,GP,JR
06996
10, 15mm, 3/4”, 7/8”
1/2”
OEM REPLACE.
FOOTNOTES
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
85219
n 37072 Ø,CN,HM
22mm, 7/8”
NO DRILL
6
10 20
74682
78058
RD, BO
n 44095 Ø,CN,HM
22mm, 7/8”
NO DRILL
5
10 20
85262
78058
RD, 4-Flat 85262 models only
l 44668 Ø,CN,HM
22mm, 7/8”
NO DRILL
6
10 15
n 37072 Ø,CN,HM
22mm, 7/8”
NO DRILL
6
10 20
74682
78058
RD, BO
n 44095 Ø,CN,HM
22mm, 7/8”
NO DRILL
5
10 20
85262
78058
RD, 4-Flat 85262 models only
l 44668 Ø,CN,HM
22mm, 7/8”
NO DRILL
6
10 15
n 33038 Ø,HM
40
1/2”
40 n 51079 AL,GP,JR
1/2”
40
1/2”
40 n 51079 AL,GP,JR
10, 15mm, 3/4”, 7/8”
1/2”
1/2”
30 n 06302 AL,GP,JR
10, 15mm, 3/4”, 7/8”
1/2”
n 51003 BF 40 n 51079 AL,GP,JR
n 51102 AL,GP,JR
10, 15mm, 3/4”, 7/8”
1/2”
40
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
3/4”, 9/16” NO DRILL
3/4”, 9/16” NO DRILL 10, 15mm, 3/4”, 7/8”
1/2”
3.5
15
l 33015 Ø,SD
18mm, 7/8”
NO DRILL
4
6
15
5 5 4
6 30 6 25 6 15
n 33021 Ø,FP,KK
18mm, 1-1/8” NO DRILL
4
6
20
n 44098
18mm, 1-1/8” NO DRILL
4
6
5
5 25
l 44569 Ø,GP,JR
18mm, 3/4”
5
5
Ø, FP, HM, KK
3.5 5 40
3.5 5 40
85219
– 74896
78013 78013
5
7.5 30
5 7.5 30 3.5 5 40
35365 44011 35365 44011 35365
74682
78058
–
–
25
78066 78113 74682, 78058 85262 85344 78058
BN
85262
BN
–
85344
78058
BN
–
–
78058
–
–
74486
78058
–
–
–
78058
–
–
74207
78013
HG
–
40
1/2”
3.5 5
40
1/2”
3.5 5
40
NO DRILL
5 5 5 5 5
30 45 30 45 30
Ø,BF,CV
3/4”, 9/16”
NO DRILL
3/4”, 9/16”
NO DRILL
Ø,BF,CV
3/4”, 9/16”
NO DRILL
n 44574 AL,JR
20
3.5 5
Ø,BF,CV
n 44011 Ø,BF,CV n 33094 AL,JR
85219
1/2”
NO DRILL
10 7.5 10 7.5 10
HG BN,RD
40
3/4”, 9/16”
– –
85217
3.5 5
Ø,BF,CV
n 44574 AL,JR
– BN
85262
1/2”
Ø,BF,CV
n 44574 AL,JR
n n n n n
NO DRILL
10, 15mm, 3/4”, 7/8” 10, 15mm, 3/4”, 7/8” 10, 15mm, 3/4”, 7/8” 10, 15mm, 3/4”, 7/8” 3/4”, 9/16”
n 33094 AL,JR 10, 15mm, 3/4”, 7/8”
14mm, 18mm NO DRILL
6 15
n 33094 AL,JR
1/2”
n 51003 BF
Venture All, Inc. AWD
–
30
4
87-95 1996
BN
74896
78-86
Van, G-Series Classic & Sport Full Size w/Lo-Mount Taillights
78058
10 15
1/4”, 1/2”, 5 9/16”
l 51083 Ø,GP,JR,RT
2009
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE 7
09-12
Uplander All, Inc. AWD (Canada Only)
DRILL BITS
1/2”, 9/16” 5
Traverse
n 51102 AL,GP,JR
WRENCHES 7/8”
02-10
n 06302 AL,GP,JR
FOOTNOTES
n 44096 HM
TrailBlazer (w/ Tow Package)
05-08
STYLE
30
l 37041 FP,JT,KK 18mm, 3/4” 1/2” NO DRILL n 51031 Ø, FP, HM, KK 18mm,
Uplander All, Inc. AWD
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
6
74180
85262 n 51152 Ø,HM
n 06955 Ø,FP,GP,KK
99-01
1/4”, 1/2”, 5 9/16”
15, 18, 21mm, 9/16", 7/16", 1/2" 30 11/16", 3/4", T50
20 15 n 88001 –
10 30
85262 n 37152 –
n 77015 Ø,HM n 77023 Ø,HM
1/2”, 9/16” 6
15, 18, 21mm, 9/16", 7/16", 1/2" 30 11/16", 3/4", T50
Tahoe New Body Style w/Amber Turn Signals 03-06
1998 99-04
7/8”
3/4”, 9/16”
NO DRILL
10, 15mm, 3/4”, 7/8”
1/2”
5 7.5 45 3.5 5 40
10, 15mm, 3/4”, 7/8”
1/2”
3.5 5
BN, BO
40
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 37042 –
Tracker 2 & 4 Dr. Tracker
n 37074 HM
74180 n 37152 –
n 88001 –
30
15, 18, 21mm, 9/16", 7/16", 1/2" 30 11/16", 3/4", T50
Tahoe New Body Style w/Amber Turn Signals 00-02
n 88001 –
6
STANDARD WIRE
n 51012 HM n 51012 HM
1/4”, 1/2”, 5 9/16”
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 7/8”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW T-CONNECTOR
n 37042 –
WRENCHES
FOOTNOTES
HITCH NUMBER
n 37152 –
95-00
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Tahoe Old Body Style
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
117
CHEVROLET
CHEVROLET
116
REESE TOWPOWER
REESE TOWPOWER
200, 4 Dr. Sedan 200 Convertible
300 All, Except 300C
n 77254 Ø,GP,JR
3/4”, 7/8”
NO DRILL
15
n 77254 Ø,GP,JR
3/4”, 7/8”
NO DRILL
15 n 06079 Ø,†,HM,JR
05-07
n 06079 Ø,†,HM,JR
08-10
APPLICATIONS GUIDE
11-13
n 06129 Ø,AE,HM,SV
300C, All Styles
05-10
n 06079 Ø,†,HM,JR n 51176 Ø,†,HM,JR n 06129 Ø,HM,JR
300C, All Styles
11-12
n 06129 Ø,AE,HM,SV
300M 300M All, Except Special Aspen
99-01 02-04 07-08
n 06284 HM,JR n 06284 HM,JR
10, 13, 15, 19mm, 3/4” 10, 13, 19mm, 3/4” 19mm, 3/4” 10, 13, 15, 19mm, 3/4” 10, 13, 15, 19mm, 3/4” 10, 13, 19mm, 3/4” 19mm, 3/4”
Concorde
93-97
n 06354 JR,TA
Concorde
98-01
n 06275 HM
Concorde Concorde Imperial
2002 03-04 90-93
n 06281 JR n 06281 JR n 06097 –
Intrepid Canada Only
93-97
n 06354 JR,TA
Intrepid Canada Only Le Baron 2 Dr. Coupe, Inc. Convertible
98-04 87-95
n 06355 JR n 06097 AO
Le Baron 4 Dr.
90-94
n 88002 – n 06097 –
LHS
94-97
n 06354 JR,TA
LHS LHS New Yorker All, Inc. Turbo
1999 00-01 86-88
n 06281 JR n 06281 JR n 06097 –
New Yorker FWD Sedan, Inc. Landau
88-90
n 06097 –
New Yorker Fifth Ave. FWD 90-93
n 06097 –
New Yorker Salon
90-93
n 06097 –
New Yorker
94-96
n 06354 JR,TA
Pacifica
04-08
Pacifica, with Factory 7-way
04-08
OEM REPLACE.
FOOTNOTES
STANDARD WIRE
T-CONNECTOR
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
DRILL BITS
WT. DISTRIB. INSTALL TIME
–
–
78042
78104
CH
–
78104
BN,CH
–
BN,CH
NO DRILL
30 30
NO DRILL
30
NO DRILL NO DRILL
30 30
NO DRILL
40
85767
78104
CH
–
NO DRILL
30
78042
78104
CH
–
NO DRILL NO DRILL
30 30
10, 13, 15, 19mm, 3/4” 10, 13, 15, 19mm, 3/4” 13mm, 11/16”
NO DRILL
40
85767
78104
CH
–
1/2” 1/2”
30 30
74224 74224 78027
78013 78013 78104
–
13mm, 11/16”
–
– – 85253
78104 85262 78013
–
85262 85219 –
13, 16, 17mm, 3/4”, 9/16”, 11/16” 13, 15mm, 9/16”, 11/16”, 7/8” 7/8”
7/8”
1/2”
5
33082 44173 33082 44173
AI
11/16”, 3/4” 1/2”
–
7/8”
1/2”
6 5 6 5
9 7.5 9 7.5
50 30 50 30
BN,CH
40 40
–
78013
–
–
35
74224
78013
BN,HG
–
30 30 40
74224 – –
78013 78013 78104
BN,HG – –
– – –
40
–
78013
BN,HG
–
30 40
74224 –
78013 78058
BN,HG –
– –
35 40
–
78104
–
–
40
–
78013
–
–
74224 – –
78013 78013 78104
BN,HG – –
– – –
13mm, 11/16”
1/8”, 3/8”, 1/2” 3/8”, 1/2”, 1” 1/2”
13mm, 11/16”
1/2”
13mm, 9/16”, 11/16” 13, 15mm, 9/16”, 11/16”, 7/8” 13mm, 3/4”
3/8” 1/8”, 3/8”, 1/2” 1/2”
1/2”
7.5 30
n n n n
1/2”
7/8”
5
7.5 30
78027 85253 –
AI
11/16”, 3/4” 1/2”
–
7/8”
1/2”
BN,CH BO
13mm, 9/16”, 11/16” 3/4”
3/8”
13mm, 9/16”, 11/16” 13, 15mm, 9/16”, 11/16”, 7/8” 13mm, 11/16”
3/8” 1/8”, 3/8”, 1/2” 1/2”
13mm, 11/16”
1/2”
13mm, 9/16”, 11/16” 13mm, 9/16”, 11/16” 13mm, 9/16”, 11/16” 13mm, 9/16”, 11/16” 13, 15mm, 9/16”, 11/16”, 7/8”
3/8”
30 30 40
3/8”
40
–
78104
–
–
3/8”
40
–
78104
–
–
3/8”
40
–
78104
–
–
1/8”, 3/8”, 1/2”
40
–
78013
–
–
78003
78104
–
–
78003
–
BN,CH
85253
1/2”
l 51084 Ø,RT,JR
06996
–
NO DRILL
l 51067 – n 06977 JR
78058
BN,CH BN,CH
30
2009 95-00
78104
NO DRILL
l 51067 –
Cirrus
85773 85773 85773 85773 78040
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
18,19mm, 3/4”
NO DRILL
3.5 5 45
l 44566 Ø,JR
18,19mm, 3/4”
NO DRILL
3.5 5
45
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
300 All, Except 300C
10, 13, 19mm, 3/4” 19mm, 3/4”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
11-12
n 51176 Ø,†,HM,JR n 06129 Ø,HM,JR
Aspen
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
11-13
n 51176 Ø,†,HM,JR n 06129 Ø,HM,JR 300 All, Except 300C
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL CHRYSLER
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
119
CHRYSLER
CHRYSLER
118
REESE TOWPOWER
CLASS II
CLASS I
95-00
n 77088 JR,KH
Sebring 2 Dr. Except Convertible
01-02
n 77088 JR,KH
Sebring 4 Dr. Only
01-06
Sebring All, Except Convertible
07-10
Sebring Sebring Sebring Sebring
Convertible Convertible Convertible Convertible
All Models All Models All Models All Models
Town & Country Mini Van, 2 WD Long Wheelbase
1996 97-00 01-06 07-10
77171 77254 77184 77184 77092 77171 77254
NO DRILL NO DRILL
Ø,HM,JR
16mm, 11/16”
NO DRILL
Ø,HM,JR
16mm, 11/16”
NO DRILL
GP
7/8”
1/2”
Ø,GP,JR
3/4”, 7/8”
NO DRILL
Ø,GP,JR
3/4”, 7/8”
NO DRILL
15 n 06526 GP,JR 15 30 30 15 15 15
–
1/2”
30
– 74721 – – – 74721 74721 –
–
n 37042 –
Town & Country All, Inc. 4 WD
96-00
n 77012 Ø,HM
18, 19mm
NO DRILL
30 n 06369 Ø,GP
Town & Country All, Inc. 4 WD
01-03
n 77012 Ø,HM
18, 19mm
NO DRILL
30 n 06369 Ø,GP
–
30 n 51062 HM
Town & Country Except Stow & Go Seats, Inc. 4 WD
04-07
n 77012 Ø,HM
18, 19mm
NO DRILL
30 n 06369 Ø,GP
–
30 n 51062 HM
06996
3.5 3.5 30
–
OEM REPLACE.
FOOTNOTES BN,CH
78058
–
BN,CH BN,CH BN,CH
– – – –
BN,CH
– –
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
40
1/4”, 1/2”, 5 9/16”
6
40
n 33046 †
3/4”
1/2”
3.5 3.5 30
74187
78058
BN
– –
3.5 3.5 30
19mm, 3/4”
1/2”
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
40
1/4”, 1/2”, 5 9/16”
6
40
n 33045 – n 44006 HM
15, 17, 18, 19mm, 7/8” 19mm, 3/4”
7/16”
3.5 5
30
1/2”
3.5 3.5 30
74658
78013
HG
–
3.5 3.5 30
19mm, 3/4”
1/2”
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
40
1/4”, 1/2”, 5 9/16”
6
40
n 33045 Ø n 44006 HM
15, 17, 18, 19mm, 7/8” 19mm, 3/4”
7/16”
3.5 5
30
1/2”
3.5 3.5 30
85245
78013
HG
–
85245
30 n 51062 HM
n 37042 – 15, 18, 21mm, 9/16", 11/16", 3/4", T50
40
1/2”
7/16", 1/2" 45
n 37152 –
n 88001 –
6
3/4”
78058 78013 78013 78104
74658
n 37042 – 15, 18, 21mm, 9/16", 11/16", 3/4", T50 18, 19mm
1/4”, 1/2”, 5 9/16”
n 33046 †,JT
7/16", 1/2" 45
n 37152 –
n 88001 –
40
BN,CH
74187
n 37042 – 15, 18, 21mm, 9/16", 11/16", 3/4", T50 18, 19mm
6
7/16", 1/2" 30
n 37152 –
n 88001 –
1/4”, 1/2”, 5 9/16”
BN,CH BN,CH
74051 n 37152 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50 18, 19mm
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
7/16", 1/2" 30
91-95
n 88001 –
WT. DISTRIB. INSTALL TIME
–
n 37042 JT
Town & Country Mini Van, 2 WD Long Wheelbase
WT. CARRYING
40
n 37152 JT
15, 18, 21mm, 9/16", 11/16", 3/4", T50
DRILL BITS
DRILL BITS 1/2”
1990
n 88001 JT
WRENCHES
–
3/4”, 7/8” 3/4”, 7/8”
FOOTNOTES
BN,CH
Ø,GP,JR Ø,GP,JR
HITCH NUMBER
–
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
BN,CH
13, 16, 17mm, 3/4”, 9/16”, 11/16” 3/4”, 7/8”
DRILL BITS
–
WRENCHES
BN,CH
FOOTNOTES
–
HITCH NUMBER
–
STYLE
30
WT. CARRYING WT. DISTRIB. INSTALL TIME
1/2”
DRILL BITS
–
WRENCHES
BN,CH
FOOTNOTES
–
HITCH NUMBER
–
INSTALL TIME STYLE
30
12, 13, 14mm, 11/16” 12, 13, 14mm, 11/16”
WRENCHES
1/2”
15, 17mm, 3/4”
FOOTNOTES
BN,CH
– – –
HITCH NUMBER
78013 78013 78013
1/2” 1/2”
IONSTALL TIME STYLE
78021 78021 78021
DRILL BITS 1/2”
30 30 30
15, 17mm, 3/4” 15, 17mm, 3/4”
n 06977 JR n n n n n n n
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
STANDARD WIRE
n 77135 JR n 77135 JR n 77135 JR
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
T-CONNECTOR
01-04 05-10 05-09
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
PT Cruiser All, Inc. GT & Turbo Models PT Cruiser All, Inc. GT & Turbo Models PT Cruiser Convertible All, Inc. GT & Turbo Models Sebring All, Except Convertible
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
Up to 200 lb TW Up to 2000 lb GTW
7/16", 1/2" 45
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
3.5 3.5 30
19mm, 3/4”
1/2”
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
40
1/4”, 1/2”, 5 9/16”
6
40
n 33045 Ø
15, 17, 18, 19mm, 7/8”
7/16”
3.5 5
n 44006 HM
19mm, 3/4”
1/2”
3.5 3.5 30
30
78000
HG
78058
–
–
74051
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
121
APPLICATIONS GUIDE
APPLICATIONS GUIDE
REESE TOWPOWER
CHRYSLER
CHRYSLER
120
REESE TOWPOWER
REESE TOWPOWER
CLASS II
–
n 44586 Ø,GP,JR
13, 15, 18mm NO DRILL
4
5
20
85777
78104
BN,CH
–
n 33045 Ø
15, 17, 18, 19mm, 7/8” 19mm, 3/4”
7/16”
3.5 5
30
85777 85245
78013
HG
1/2”
3.5 3.5 30
DRILL BITS
13, 15, 18mm
–
13, 15, 18mm
–
20 20
18, 19mm
–
n 51203 Ø,GP,JR 30 n 51062 HM
n 51203 Ø,GP,JR
Voyager All, Inc. 4 WD
n 06550 Ø,GP,JR n 51192 Ø,GP,JR
01-03
n 77012 Ø,HM
18, 19mm
NO DRILL
30 n 06369 Ø,GP
n 37042 –
n 88001 –
DODGE
Avenger
95-00
n 77088 JR,KH
Avenger
08-10
n n n n n
Avenger Caliber All, Except R/T Caliber All, Except R/T & SRT-4 Caravan Caravan Short Wheelbase, 2 WD Only
11-13 2007 08-12 84-90 84-90
77171 77254 77254 77145 77145
1/2”
30
Ø,GP,JR
12, 13, 14mm, 11/16” 3/4”, 7/8”
NO DRILL
Ø,GP,JR
3/4”, 7/8”
NO DRILL
15 n 06526 GP,JR 15 15 15 15 n 06080 GW,GP
Ø,GP,JR
3/4”, 7/8”
NO DRILL
Ø,GP
15/16”
NO DRILL
Ø,GP
15/16”
NO DRILL
15, 18, 21mm, 9/16", 11/16", 3/4", T50
3/4”, 7/8”
11/16”, 7/8”
Caravan Short Wheelbase, 2 & 4 WD Caravan Short Wheelbase, 2 WD Only
n 06080 GW,GP
91-95 91-95
1/2”
15/32”
96-00 96-00
n 77012 GP,QS n 77012 Ø,HM
18, 19mm
NO DRILL
18, 19mm
NO DRILL
15 30 n 06369 Ø,GP
15/32”
1/4”, 1/2”, 5 9/16”
6
40
n 44006 HM
7/16", 1/2" 30
18, 19mm
–
BN,CH
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
40
1/4”, 1/2”, 5 9/16”
6
40
n 33046 †,JT
3/4”
1/2”
3.5 3.5 30
–
HG
–
78058
74722 74722 85773 74705 85775 – –
78104
–
–
BN,CH
–
BN,CH
78104 78104 78104 78058 78058
–
78058 78058
BN
78013 78013
HG
BN,CH BN,CH CH –
– – – – –
74051
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
40
1/4”, 1/2”, 5 9/16”
6
40
n 44618 – n 33046 †,JT
7/8”, 11/16” 1/2” 3/4”
1/2”
3.5 5 30 3.5 3.5 30
74187 74187
BN
– –
74187
30 n 51062 HM
n 37042 –
06996
40
30
15, 18, 21mm, 9/16", 11/16", 3/4", T50
15, 18, 21mm, 9/16", 11/16", 3/4", T50
6
7/16", 1/2" 30
n 37152 –
n 88001 –
1/4”, 1/2”, 5 9/16”
30
n 37042 JT
Caravan All, Except Sport Caravan All, Inc. 2 & 4 WD
4 4 20 3.5 3.5 30
30
n 37152 JT
n 88001 JT
20
85245
n 37042 JT 15, 18, 21mm, 9/16", 11/16", 3/4", T50 11/16”, 7/8”
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
4
7/16", 1/2" 45
n 37152 JT
n 88001 JT
13, 15, 18mm NO DRILL 19mm, 3/4” 1/2”
4
7/16", 1/2" 45
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
3.5 3.5 30
19mm, 3/4”
1/2”
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
40
1/4”, 1/2”, 5 9/16”
6
40
n 33045 – n 44006 HM
15, 17, 18, 19mm, 7/8” 19mm, 3/4”
7/16”
3.5 5
30
1/2”
3.5 3.5 30
74658 74658
74658
HG
– –
HG
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 37152 –
13, 15, 18mm NO DRILL
OEM REPLACE.
STANDARD WIRE
CH
FOOTNOTES
T-CONNECTOR
78104
WT. DISTRIB. INSTALL TIME
85775
WT. CARRYING
20
DRILL BITS
5
WRENCHES
4
FOOTNOTES
13, 15, 18mm NO DRILL
–
HITCH NUMBER
n 44586 Ø,GP,JR
13, 15, 18mm
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
25 20 20
n 51175 Ø,HM n 06550 Ø,GP,JR n 51192 Ø,GP,JR
DRILL BITS
– –
08-10
WRENCHES
15mm, 18mm 13, 15, 18mm
Town & Country
FOOTNOTES
–
HITCH NUMBER
–
STYLE
78058
WT. CARRYING WT. DISTRIB. INSTALL TIME
78000
15mm, 18mm
DRILL BITS
25
n 06992 Ø,HM
WRENCHES
3.5 4
FOOTNOTES
15mm, 18mm NO DRILL
INSTALL TIME STYLE
n 44176 Ø
05-07
11-13
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
25
Town & Country w/Stow & Go Seats, Inc. 4 WD
Town & Country
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
–
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
123
CHRYSLER - DODGE
CHRYSLER - DODGE
122
REESE TOWPOWER
REESE TOWPOWER
–
n 37152 – n 37042 – n 88001 – Caravan Except Stow & Go Seats, Inc. 2 & 4 WD
04-07
n 77012 Ø,HM
18, 19mm
NO DRILL
30 n 06369 Ø,GP
15, 18, 21mm, 9/16", 7/16", 1/2" 45 11/16", 3/4", T50 18, 19mm – 30 n 51062 HM
n 37152 –
n 88001 – Caravan Cargo Van Long Wheelbase, 2 WD Only Caravan Cargo Van Short Wheelbase, 2 & 4 WD Caravan Cargo Van Short Wheelbase, 2 WD Only
91-93
n 06080 JT
15, 18, 21mm, 9/16", 7/16", 1/2" 45 11/16", 3/4", T50 11/16”, 7/8” 15/32” 30
91-95
n 06080 GW,GP
11/16”, 7/8”
15/32”
n 37042 JT
Caravan Cargo Van Long Wheelbase, 2 WD Only, Except LE Challenger All Models
Challenger All Models Charger All Models
Charger, All Models Dakota Pickup Inc. Extended Cab
94-95
n 06080 JT
08-10
n n n n n n n n n
11-12 06-10
11-12 87-94
06079 51176 06129 06128 06079 51176 06129 06128 06250
3.5 3.5 30
19mm, 3/4”
1/2”
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
40
1/4”, 1/2”, 5 9/16”
6
40
n 33045 Ø
15, 17, 18, 19mm, 7/8”
7/16”
3.5 5
n 44006 HM
19mm, 3/4”
1/2”
3.5 3.5 30
30
78000
OEM REPLACE.
FOOTNOTES
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
DRILL BITS
85245
–
HG
78058
–
–
74187
78058
BN
–
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
40
1/4”, 1/2”, 5 9/16”
6
40
n 44618 –
7/8”, 11/16” 1/2”
3.5 5
30
74187
78058
BN
–
n 33046 †,JT
3/4”
3.5 3.5 30
74187
78058
BN
–
1/2”
BN
–
30 30 40 35 30 30 30 35 40 n 51025 GU
78040
78058
–
–
78040 78040
78058 78058
– –
– –
85765 74182
78104 78058
BN
– –
78058
BN,HJ
–
NO DRILL
Ø,HM,JR
10, 13, 19mm, 3/4” NO DRILL
Ø,HM,JR
10, 13, 19mm, 3/4” NO DRILL
Ø,†,HM,JR
10, 13, 19mm, 3/4” NO DRILL
Ø,†,HM,JR
19mm, 3/4”
Ø,HM,JR
10, 13, 19mm, 3/4” NO DRILL
NO DRILL
Ø,HM,JR
10, 13, 19mm, 3/4” NO DRILL
GU
18mm, 1/2”, 5/8”, 11/16”, 3/4”, 7/8”
1/2”
n 37042 GU n 51025 GU
18mm, 1/2”, 5/8”, 11/16”, 3/4”, 7/8” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 18mm, 1/2”, 5/8”, 11/16”, 3/4”, 7/8”
1/2”
3.5 5 30
1/4”, 1/2”, 5 9/16”
6
35
1/4”, 1/2”, 5 9/16”
6
35
1/2”
n 36047 GU
3/4”, 9/16”
n 44102 GU
18mm, 1/2”, 1/2” 5/8”, 11/16”, 3/4”, 7/8”
1/2”
5
7
30
3.5 5
30
1/2”
CH
3.5 5 30
7/16", 1/2" 40
74182
40 n 51025 GU n 37152 GU n 37042 GU n 51025 GU
06996
40
3.5 3.5 30
HG
78058
NO DRILL
15, 18, 21mm, 9/16", 11/16", 3/4", T50
6
1/2”
78013
74187
19mm, 3/4”
n 88001 CT,GU
1/4”, 1/2”, 5 9/16”
n 44006 HM
85245
30
19mm, 3/4”
n 06250 GU
40
30
15/32”
n 37152 GU
Dakota Pickup All, Inc. RT & Dakota 95-96 Sport w/Step Bumper
6
3.5 5
74187
Ø,†,HM,JR
15, 18, 21mm, 9/16", 11/16", 3/4", T50 18mm, 1/2”, 5/8”, 11/16”, 3/4”, 7/8”
1/4”, 1/2”, 5 9/16”
7/16”
7/16", 1/2" 30
Ø,†,HM,JR
n 88001 GU
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
15, 17, 18, 19mm, 7/8” 19mm, 3/4”
74051
n 37152 JT
15, 18, 21mm, 9/16", 11/16", 3/4", T50 11/16”, 7/8”
n 33045 Ø
1/2”
30
91-95
n 88001 JT
3.5 3.5 30
19mm, 3/4”
7/16", 1/2" 40
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
18mm, 1/2”, 5/8”, 11/16”, 3/4”, 7/8” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 18mm, 1/2”, 5/8”, 11/16”, 3/4”, 7/8”
1/2”
3.5 5 30
1/4”, 1/2”, 5 9/16”
6
35
1/4”, 1/2”, 5 9/16”
6
35
1/2”
n 36047 GU
3/4”, 9/16”
n 44102 GU
18mm, 1/2”, 1/2” 5/8”, 11/16”, 3/4”, 7/8”
1/2”
5
7
30
3.5 5
30
74475
3.5 5 30 74475
HJ
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 37042 –
WRENCHES
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
30 n 51062 HM
STANDARD WIRE
18, 19mm
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
30 n 06369 Ø,GP
WIRING
Up to 2500 lb TW Up to 18000 lb GTW T-CONNECTOR
NO DRILL
STYLE
18, 19mm
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
n 77012 Ø,HM
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW WT. CARRYING WT. DISTRIB. INSTALL TIME
01-03
STYLE
YEAR
MODEL
Caravan All, Inc. 2 & 4 WD
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
125
DODGE
DODGE
124
REESE TOWPOWER
REESE TOWPOWER
n 37152 CT,GU n 37042 CT,GU n 51025 Ø,GU n 88001 CT,GU n 06250 Ø,GU
1/2”
40 n 51025 Ø,GU
n 51025 Ø,GU
Dakota Pickup All Models
18mm, 1/2”, 5/8”, 11/16”, 3/4”, 7/8”
1/2”
40 n 37152 CT,GU
n 37042 CT,GU
n 51025 Ø,GU n 88001 CT,GU Dakota Pickup All Models
15, 18, 21mm, 9/16", 11/16", 3/4", T50
18mm, 1/2”, 5/8”, 11/16”, 3/4”, 7/8”
1/2”
40 n 37152 CT,GU
n 37042 CT,GU
n 51025 Ø,GU n 88001 CT,GU
15, 18, 21mm, 9/16", 11/16", 3/4", T50
n 51138 Ø,HM
Dakota Pickup All Models
10-11
n 51138 Ø,HM
Dart, All Models w/Dual Exhaust Dart, All Models w/Dual Exhaust Durango
2013 2013 98-99
3/4”
NO DRILL NO DRILL
35
n 36025 GU
1/2”
30
8
18mm, 1/2”, 5/8”, 11/16”, 3/4”, 7/8” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 18mm, 1/2”, 5/8”, 11/16”, 3/4”, 7/8”
1/2”
3.5 5 30
n 36047 Ø,GU
3/4”, 9/16”
18mm, 1/2”, 1/2” 5/8”, 11/16”, 3/4”, 7/8” 3/4” 1/2”
6
35
n 44102 Ø,GU
1/4”, 1/2”, 5 9/16”
6
35
n 36025 GU
18mm, 1/2”, 1/2” 5/8”, 11/16”, 3/4”, 7/8” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 18mm, 1/2”, 5/8”, 11/16”, 3/4”, 7/8”
3.5 5 30
6
35
1/4”, 1/2”, 5 9/16”
6
35
18mm, 1/2”, 1/2” 5/8”, 11/16”, 3/4”, 7/8” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 18mm, 1/2”, 5/8”, 11/16”, 3/4”, 7/8”
1/2”
5
7
30
3.5 5
30
5
30
8
74475
22mm, 1-1/8” 22mm, 1-1/8”
OEM REPLACE.
HJ
78058
BN,HJ
–
n 36047 Ø,GU n 36025 GU n 44102 Ø,GU
HJ
3/4”, 9/16”
1/2”
5
7
30
74475
78058
BN,HJ
85253
3/4”
1/2”
5 8 3.5 5
30 30
74475
78058
BN,HJ
85253
18mm, 1/2”, 1/2” 5/8”, 11/16”, 3/4”, 7/8”
3.5 5 30
3.5 5 30
1/4”, 1/2”, 5 9/16”
6
35
1/4”, 1/2”, 5 9/16”
6
35
1/2”
–
3.5 5 30
1/4”, 1/2”, 5 9/16”
1/2”
BN,HJ
3.5 5 30
1/4”, 1/2”, 5 9/16”
1/2”
FOOTNOTES
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
STANDARD WIRE
5
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
DRILL BITS
6
30
78058
n 36047 Ø,GU n 36025 GU n 44102 Ø,GU
HJ
3/4”, 9/16”
1/2”
5
7
30
–
–
BN
85253
3/4”
1/2”
5 8 3.5 5
30 30
74187
78058
BN,HJ
85253
18mm, 1/2”, 1/2” 5/8”, 11/16”, 3/4”, 7/8”
3.5 5 30 HJ
NO DRILL
5
8 20
n 33092 Ø,HM
22mm, 1-1/8” NO DRILL
5
8
20
74187
78058
BN,HJ
85253
NO DRILL
5
8 20
n 33092 Ø,HM
22mm, 1-1/8” NO DRILL
5
8
20
74187
78058
BN,HJ
85253
NO DRILL
3.5 5 15
n 33056 Ø n 44064 Ø
3/4”
NO DRILL
78013
–
–
NO DRILL
5 7.5 30 3.5 5 20
74658
3/4”, 7/8”
20 15 n 06960 Ø
06996
1/4”, 1/2”, 5 9/16”
3.5 5
74475
74187
05-09
3/4”
n 44102 Ø,GU
30
7/16", 1/2" 40
Dakota Pickup All Models
n 77278 Ø,HM n 77278 Ø,HM
35
7
74475 n 51025 Ø,GU
n 06250 Ø,GU
6
5
7/16", 1/2" 40
2004
Dakota Pickup All, Except Quad Cab 2004
18mm, 1/2”, 1/2” 5/8”, 11/16”, 3/4”, 7/8” 3/4” 1/2”
1/4”, 1/2”, 5 9/16”
1/2”
74475 n 51025 Ø,GU
n 06250 Ø,GU
3/4”, 9/16”
7/16", 1/2" 40
02-03
Dakota Pickup All, Except Quad Cab 02-03
n 36047 Ø,GU
74475
n 37042 CT,GU
15, 18, 21mm, 9/16", 11/16", 3/4", T50
3.5 5 30
7/16", 1/2" 40
n 37152 CT,GU
n 88001 CT,GU
1/2”
3/4”, 7/8”
–
15 n 51035 Ø
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
3/4”, 7/8”
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
Dakota Pickup All, Inc. RT & Dakota 00-01 Sport w/Step Bumper
15, 18, 21mm, 9/16", 11/16", 3/4", T50 18mm, 1/2”, 5/8”, 11/16”, 3/4”, 7/8”
18mm, 1/2”, 5/8”, 11/16”, 3/4”, 7/8” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 18mm, 1/2”, 5/8”, 11/16”, 3/4”, 7/8”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW T-CONNECTOR
40 n 51025 Ø,GU
WRENCHES
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
DRILL BITS 1/2”
STYLE
18mm, 1/2”, 5/8”, 11/16”, 3/4”, 7/8”
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW WT. CARRYING WT. DISTRIB. INSTALL TIME
n 06250 Ø,GU
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Dakota Pickup All, Inc. RT & Dakota 97-99 Sport w/Step Bumper
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
127
DODGE
DODGE
126
REESE TOWPOWER
REESE TOWPOWER
n 51067 – l 51148 Ø,RT
7/8”
1/2”
18, 21mm, 3/4”, 7/8”
NO DRILL
3.5 5 15
5 6
7.5 30 9 20
n 33056 Ø n 44064 Ø n 33082 AI l 44173 – l 44175 Ø
Durango
2009
Durango Dynasty
11-13 88-93
n 06097 –
Grand Caravan Long Wheelbase, 2 WD Only
84-90
n 88002 – n 06080 GW,GP,JT
n 51067 –
7/8”
1/2”
5
7.5 30
n 51067 –
7/8”
1/2”
5
7.5 30
13mm, 9/16”, 11/16” 3/4”
3/8”
40
1/2”
11/16”, 7/8”
15/32”
35 30 n 37152 JT n 37042 JT
n 88001 JT Grand Caravan Long Wheelbase, 2 WD Only
n 06080 JT
91-93
15, 18, 21mm, 9/16", 11/16", 3/4", T50 11/16”, 7/8”
Grand Caravan Long Wheelbase, 2 94-95 WD Only, Except LE
n 06080 JT
15, 18, 21mm, 9/16", 11/16", 3/4", T50 11/16”, 7/8”
Grand Caravan All, Inc. 4 WD
96-00
n 77012 Ø,HM
18, 19mm
NO DRILL
30 n 06369 Ø,GP
15, 18, 21mm, 9/16", 11/16", 3/4", T50 18, 19mm
15/32”
30 n 37152 JT
Grand Caravan All, Inc. 4 WD
01-03
n 77012 Ø,HM
18, 19mm
NO DRILL
30 n 06369 Ø,GP
15/32”
30 n 37152 JT
06996
7/8”
11/16”, 3/4” 1/2” 7/8”
1/2”
21mm
NO DRILL
3/4”
1/2”
–
BN,RD BN,CH
85253 –
OEM REPLACE.
78058 78104
FOOTNOTES
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
85253 78027
6
9
6 5
9 50 7.5 30
78027
78104
BN,CH
–
6 5 6
9 50 7.5 30 7.5 20
78027
78104
BN,CH
–
85775 –
78104 78058
CH –
– –
–
78058
–
–
78058
BN
–
78058
BN
–
78013
HG
–
20
3.5 3.5 30
30
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6
n 33046 †,JT
3/4”
1/2”
3.5 3.5 30
74187
30
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6
n 33046 †,JT
3/4”
1/2”
3.5 3.5 30
74187
30
30 n 51062 HM
3.5 3.5 30
19mm, 3/4”
1/2”
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6
n 33045 – n 44006 HM
15, 17, 18, 19mm, 7/8” 19mm, 3/4”
7/16”
3.5 5
30
1/2”
3.5 3.5 30
74658
30
7/16", 1/2" 45 –
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS 1/2”
–
74187
74658
30 n 51062 HM
n 37042 – 15, 18, 21mm, 9/16", 11/16", 3/4", T50
18, 21mm NO DRILL deep socket, 3/4”, 7/8” 11/16”, 3/4” 1/2”
BN,HG
9 50 7.5 30
7/16", 1/2" 30
n 37152 –
n 88001 –
6
1/2”
78013
74187
n 37042 – 15, 18, 21mm, 9/16", 11/16", 3/4", T50 18, 19mm
1/4”, 1/2”, 5 9/16”
n 33046 †,JT
7/8”
74658
6 5
7/16", 1/2" 30
n 37152 –
n 88001 –
6
11/16”, 3/4” 1/2”
5 7.5 30 3.5 5 20
74051
n 37042 JT n 88001 JT
1/4”, 1/2”, 5 9/16”
n 33082 AI n 44173 – l 44662 Ø,CS,HM
NO DRILL NO DRILL
7/16", 1/2" 30
n 37042 JT n 88001 JT
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
n 33082 AI n 44173 –
3/4” 3/4”, 7/8”
7/16", 1/2" 45
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
3.5 3.5 30
19mm, 3/4”
1/2”
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6
n 33045 Ø n 44006 HM
15, 17, 18, 19mm, 7/8” 19mm, 3/4”
7/16”
3.5 5
30
1/2”
3.5 3.5 30
85245
HG
78013
HG
–
30 85245
HG
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
Durango
07-08
WRENCHES
FOOTNOTES
STYLE
NO DRILL
STANDARD WIRE
Durango w/ OEM 7-Way (4-Flat Upgrade) 00-08 04-06 Durango
3/4”, 7/8”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW T-CONNECTOR
15 n 51035 Ø
WT. CARRYING WT. DISTRIB. INSTALL TIME
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
DRILL BITS –
DRILL BITS
3/4”, 7/8”
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
WRENCHES
n 06960 Ø
00-03
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Durango
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
129
DODGE
DODGE
128
REESE TOWPOWER
REESE TOWPOWER
–
n 37152 –
n 37042 –
Grand Caravan w/Stow & Go Seats, Inc. 4 WD
05-07
Grand Caravan
08-10
Grand Caravan, All Styles
n 06992 Ø,HM n n n n n
11-13
51175 06550 51192 06550 51192
15, 18, 21mm, 9/16", 11/16", 3/4", T50 15mm, 18mm
–
25 25 20 20 20 20
Ø,HM
15mm, 18mm
–
13, 15, 18mm
–
Ø,GP,JR
13, 15, 18mm
–
Ø,GP,JR
13, 15, 18mm
–
Ø,GP,JR
13, 15, 18mm
–
n 06354 JR,TA
Intrepid Journey Journey Journey Magnum All Models
98-04 2009 2010 11-12 05-08
n 06355 JR
Mini-Ram Neon 2 & 4 Dr. Neon 2 & 4 Dr. Neon All, Inc. R/T Nitro Nitro Pickup, D/W Series, Full Size
84-88 95-99 00-01 02-05 2007 08-10 67-70
13, 15mm, 9/16”, 1/8”, 3/8”, 11/16”, 7/8” 1/2” 13mm, 3/4” 1/2”
n 77121 – n 77052 GP,JR n 77052 GP,JR
11/16”, 7/8”
7/16”
7/8”
1/2”
7/8”
1/2”
06079 51176 06129 06080
6
Ø,HM,JR, †
10, 13, 19mm, 3/4” NO DRILL
Ø,HM,JR
19mm, 3/4”
NO DRILL
Ø,HM,JR
10, 13, 19mm, 3/4” NO DRILL
GW,GP
11/16”, 7/8”
15/32”
n 51017 GP
OEM REPLACE.
FOOTNOTES
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
–
13, 15, 18mm NO DRILL
4
4
25
78000
78058
–
–
n 44586 Ø,GP,JR
13, 15, 18mm NO DRILL
4
5
20
85775
78104
CH
–
n 44586 Ø,GP,JR
13, 15, 18mm NO DRILL
4
5
20
85777
–
BN,CH
–
85777 N/A
78013
–
–
74224 78086 85717 – 78039
– – – – 78104
BN,HG
– – – – –
– – – – 78017 78017
78058 78058 78058 78058 78104 78104
CH
– – – – – –
–
–
–
–
–
–
–
10
12 40 –
–
–
–
10
12 40
12
14 45
20
3/4”
NO DRILL
3/4”
NO DRILL
3/4”
NO DRILL
4 4 4
4 4 4
25 25 25
n 44601 Ø,HM,JR n 44601 Ø,HM,JR n 44601 Ø,HM,JR
3/4”
NO DRILL
3/4”
NO DRILL
3/4”
NO DRILL
3/4”
1/2”
4 4 4
4 4 4
25 25 25
3.5 3.5 30
5 5 13, 18, 19mm, 3/16”, 9/32”, 5
6 20 6 20 10 40
n 44559 Ø,GP n 44559 Ø,GP n 36025 –
NO DRILL NO DRILL
3/4”
1/2”
6 6 8
20 20 30 n 41902 @,DB,GP, † 3/4”, 13/16”, 9/16”
NO DRILL
NO DRILL
3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8” 9/16”, 3/4”
1/2”, 17/32” 3/16”, 9/32”, 5 1/2”, 17/32”
10 40
5
7.5 25
n 36025 FP,GU
3/4”
13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8”
3/16”, 9/32”, 5 1/2”, 17/32” 3/16”, 9/32”, 5 1/2”, 17/32”
10 40
l 37034 GU
15/16", 3/4” 5/8”
7
12 25 n 96902 @,DB,GB
10 40
l 37094 GU
15/16", 3/4” 5/8”
7
12 25 n 45005 #,HX,TF
1/2”
6
10 25
1/2”
6
10 25
1/2”
5 5
8 30 10 45
1/2”
18, 19mm 18, 19mm
5 5 5
18, 19mm 18, 19mm
71-85
7/8” 3/4”, 13/16”, 9/16” 7/8”
10
12 40
10
12 40
7.5 12 30 n 41902 @,DB,GB, † 3/4”, 13/16”, 9/16”
10
12 40 –
10
12 40
12
14 45
n 96902 @,DB,GB
18mm, 3/4” HM,HX deep socket n 44109 FP,GP, GU,HX 18mm, 3/4” deep socket 3/4” n 36025 –
1/2”
n 37081 CQ
13, 18, 19mm, NO DRILL 7/8”
l 37069 GU
9/16”, 3/4”
1/2”
5
7.5 25
n 36025 FP,GU
3/4”
n 51016 HM
13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8”
3/16”, 9/32”, 1/2”, 17/32” 3/16”, 9/32”, 1/2”, 17/32”
5
10 40
l 37034 GU
15/16", 3/4” 5/8”
7
12 25 n 96902 @,DB,GB
5
10 40
l 37094 GU
15/16", 3/4” 5/8”
7
12 25 n 45005 #,HX,TF
1/2”
6
10 25
1/2”
6
10 25
1/2”
5
8
n 51017 GP
n 44108 FP,GU,
18mm, 3/4” HM,HX deep socket n 44109 FP,GP, GU,HX 18mm, 3/4” deep socket 3/4” n 36025 –
n 88001 GU
–
3.5 4
n 44108 FP,GU,
73-85
78058
15mm, 18mm NO DRILL
n 33046 †,JT
l 37069 GU
71-72
78000
n 44176 Ø
30 20 20 n 51089 Ø,GP n 51089 Ø,GP n 51016 HM
06996
30
40
30 30 30 30
n 51016 HM
Pickup, D/W Series, Full Size w/Deep Drop Bumper Pickup, D/W Series, Full Size
FOOTNOTES
3.5 3.5 30
HITCH NUMBER
1/2”
1/4”, 1/2”, 5 9/16”
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
19mm, 3/4”
6
DRILL BITS
n 44006 HM
1/4”, 1/2”, 5 9/16”
WRENCHES
3.5 5
FOOTNOTES
DRILL BITS
7/16”
30
n 51017 GP Pickup, D/W Series, Full Size
15, 17, 18, 19mm, 7/8”
40 l 97208 Ø,HM,JR l 97208 Ø,HM,JR l 97208 Ø,HM,JR
n n n n
n 33045 Ø
74051
n 51203 Ø,GP,JR 93-97
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
3.5 3.5 30
7/16", 1/2" 45
Ø,GP,JR
Intrepid
19mm, 3/4” 1/2”
15, 18, 21mm, 9/16", 7/16", 1/2" 30 11/16", 3/4", T50
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
1/2”
7/8” 3/4”, 13/16”, 9/16” 7/8” 3/4”, 15/16” 1/2”, 3/8”, 5/8”
7.5 12 30 n 41902 @,DB,GB, † 3/4”, 13/16”, 9/16”
7/8” 3/4”, 13/16”, 9/16” 7/8” 3/4”, 15/16” 1/2”, 3/8”, 5/8”
BN,CH
CH – – BN,CH
– – – – BN,CH
30 74051
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 88001 –
WRENCHES
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
30 n 51062 HM
STANDARD WIRE
18, 19mm
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
30 n 06369 Ø,GP
T-CONNECTOR
NO DRILL
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
STYLE
18, 19mm
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
n 77012 Ø,HM
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW WT. CARRYING WT. DISTRIB. INSTALL TIME
04-07
STYLE
YEAR
MODEL
Grand Caravan Except Stow & Go Seats, Inc. 4 WD
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
131
DODGE
DODGE
130
REESE TOWPOWER
REESE TOWPOWER
Pickup, D/W Series, Full Size w/Deep Drop Bumper Pickup, Ram, Full Size
15, 18, 21mm, 9/16", 11/16", 3/4", T50
1/2”
6
10 25
1/2”
5
8
5
10 45
–
BN,HJ
–
–
BN,HJ
–
15/16", 3/4” 5/8”
7
12 40 n 41923 @,GP,SA, † 3/4”, 13/16”, 9/16”
12
14 35 74182
n 37096 JL
15,17,18, 19,21, 22mm, 9/16”,3/4” 13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8” 7/8”
1/4”, 1/2”, 5 9/16”
6.5 45
l 37094 GU
15/16", 3/4” 5/8”
7
12 40 n 96923 @,GP,SA
7/8” 3/4”, 13/16”, 9/16” 7/8”
12
14 35
3/16”, 5 9/32”, 1/2”, 17/32” 3/16”, 5 9/32”, 1/2”, 17/32” 1/2” 5
10 40
n 44103 GU
7/8”
1/2”
5
10 20 n 45005 #,HX,TF
3/4”, 15/16” 1/2”, 3/8”, 5/8”
12
14 45
10 40
n 44108 Ø,FP,GU, HM,HX
18mm, 3/4” deep socket
1/2”
6
10 25
10 15
n 44109 Ø,FP,GP,
18mm, 3/4” deep socket
1/2”
6
10 25 74182
n 51017 GP,FP
9/16”, 3/4”
1/2”
5
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 7/8” 1/2” 5 13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8”
3/16”, 5 9/32”, 1/2”, 17/32” 3/16”, 5 9/32”, 1/2”, 17/32”
5
10 45
74182
–
BN,HJ
–
15/16", 3/4” 5/8”
74475
–
BN,HJ
–
–
BN,HJ
–
7.5 40 6.5 45
l 37034 GU l 37094 GU
15/16", 3/4” 5/8”
7 7
12 40 12 40
10 15
n 44103 GU
7/8”
1/2”
5
10 20 n 41923 @,GP,SA, † 3/4”, 13/16”, 9/16”
12
14 35 74182
10 40
n 44108 Ø,FP,GU, HM,HX
18mm, 3/4” deep socket
1/2”
6
10 25 n 96923 @,GP,SA
7/8” 3/4”, 13/16”, 9/16” 7/8”
12
14 35
10 40
n 44109 Ø,FP,GP,
18mm, 3/4” deep socket
1/2”
6
10 25 n 45005 #,HX,TF
3/4”, 15/16” 1/2”, 3/8”, 5/8”
12
14 45
GU,HX
HJ
13, 18, 19mm, NO DRILL 7/8”
7/16", 1/2" 30
74475 n 37081 CQ
95-98 99-01
HJ
74182
l 37034 GU
l 37069 GU n 37096 JL
l 37069 GU n 37096 JL
9/16”, 3/4” 1/2”
n 51039 –
7/8”
n 51016 HM,FP n 51017 GP,FP
5
10 45
74475
–
BN,HJ
–
3/4”
7.5 12 30 7 12 40
74475
–
BN,HJ
–
n 37017 †,GU l 37034 GU
15/16", 3/4” 5/8”
5
10 15
l 37094 GU n 44103 GU
7/8”
13, 18, 19mm, 3/16”, 5 3/4”, 13/16” 9/32”, 1/2”, 17/32” 13, 18, 19mm, 3/16”, 5 3/4”, 13/16”, 9/32”, 1/2”, 7/8” 17/32”
10 40 10 40
1/2”
1/2”
15/16", 3/4” 5/8” 1/2”
7 5
12 40 10 20 n 41923 @,GP,SA, † 3/4”, 13/16”, NO DRILL
7/16", 1/2" 30
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
12
14 35 74182
–
BN,HJ
–
n 96923 @,GP,SA
7/8” 3/4”, 13/16”, NO DRILL 7/8”
12
14 35 74182
–
BN,HJ
–
n 45010 #,TF
3/4”
12 14 30
1/2”
74475 n 37081 CQ
99-01
HJ
13, 18, 19mm, NO DRILL 7/8”
7.5 40 6.5 45
5
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4”
–
30
13, 18, 19mm, NO DRILL 7/8”
GU,HX
BN,HJ
OEM REPLACE.
10 25
7/16", 1/2" 30
95-98
06996
6
7.5 40
n 51016 HM,FP
Pickup, Ram, Full Size w/Deep Drop Bumper
1/2”
n 37081 CQ
n 37081 CQ
15, 18, 21mm, 9/16", 11/16", 3/4", T50
14 45
5
1994
n 88001 GU
12
1/2”
n 51039 –
Pickup, Ram, Full Size w/Deep Drop Bumper Pickup, Ram, Full Size
3/4”, 15/16” 1/2”, 3/8”, 5/8”
9/16”, 3/4”
n 51039 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
12 25 n 45005 #,HX,TF
l 37069 GU
n 51017 GP,FP
n 88001 GU
7
FOOTNOTES
15/16", 3/4” 5/8”
STANDARD WIRE
l 37094 GU
–
74182
n 51016 HM,FP
Pickup, Ram, Full Size w/Deep Drop Bumper Pickup, Ram, Full Size
12 40
7/16", 1/2" 30
1994
15, 18, 21mm, 9/16", 11/16", 3/4", T50
10
T-CONNECTOR
10 40
86-93
n 88001 GU
12 25 n 96902 @,DB,GB
7.5 12 30 n 41902 @,DB,GB, † 3/4”, 13/16”, 9/16”
13, 18, 19mm, NO DRILL 7/8”
5
10 40
74475
HJ
–
BN,HJ
–
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 88001 GU
WT. DISTRIB. INSTALL TIME
7
DRILL BITS
15/16", 3/4” 5/8”
18mm, 3/4” HM,HX deep socket n 44109 FP,GP, GU,HX 18mm, 3/4” deep socket 3/4” n 36025 –
12 40 74182
WRENCHES
l 37034 GU
n 44108 FP,GU,
WT. CARRYING
n 51017 GP
10
FOOTNOTES
10 40
13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8”
7/8” 3/4”, 13/16”, 9/16” 7/8”
1/2”
HITCH NUMBER
3/16”, 5 9/32”, 1/2”, 17/32” 3/16”, 5 9/32”, 1/2”, 17/32”
n 51016 HM
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
3/4”
DRILL BITS
n 36025 FP,GU
9/16”, 3/4” 1/2”
WRENCHES
7.5 25
l 37069 GU
FOOTNOTES
STYLE
5
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB. INSTALL TIME
86-93
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Pickup, D/W Series, Full Size
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
133
DODGE
DODGE
132
REESE TOWPOWER
REESE TOWPOWER
2002
n 51039 –
7/8”
n 51016 HM,FP
l 37069 GU n 37096 JL
n 51039 – n 88001 GU Pickup, Ram, Full Size 3500 Only, w/ 2002 Deep Drop Bumper 02-03 Pickup, Ram, Full Size 1500 Only Built Before 11/2002 2003 Pickup, Ram, Full Size 1500 Built After 11/2002
15, 18, 21mm, 9/16", 11/16", 3/4", T50
l 37094 GU n 44103 GU
7/8”
13, 18, 19mm, 3/16”, 5 3/4”, 13/16” 9/32”, 1/2”, 17/32” 13, 18, 19mm, 3/16”, 5 3/4”, 13/16”, 9/32”, 1/2”, 7/8” 17/32”
10 40 10 40
9/16”, 3/4”
1/2”
5
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8” 7/8”
3/16”, 9/32”, 5 1/2”, 17/32” 3/16”, 9/32”, 5 1/2”, 17/32”
n 51143 Ø,CP,GU
n 51143 Ø,CP,GU
n 51143 Ø,CP,GU
06-08
1/2”
15/16", 3/4” 5/8” 1/2”
7 5
1/2”
5
7.5 40 6.5 45
–
BN,HJ
–
BN,HJ
12
14 35 74182
n 96923 @,GP,SA
12
14 35
n 45010 #,TF
3/4”
12 14 30
3/4”, 15/16” NO DRILL
3/4”, 15/16” NO DRILL
3/4”, 15/16” NO DRILL
3/4”, 15/16” NO DRILL
5
10 45
74475
–
BN,HJ
–
3/4”
74475
–
BN,HJ
–
–
BN,HJ
–
15/16", 3/4” 5/8”
7.5 12 30 7 12 40
l 37094 GU
15/16", 3/4” 5/8”
7
1/2”
12 40 n 41923 @,GP,SA, † 3/4”, 13/16”, NO DRILL
12
14 35 74182
10 40
n 96923 @,GP,SA
7/8” 3/4”, 13/16”, NO DRILL 7/8”
12
14 35
3/4”
12
14 30
5
5
5
5
8 20
8 20
8 20
8 20
8 20
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
OEM REPLACE.
HJ
5
n 37017 †,GU l 37034 GU
n 44103 GU
–
13, 18, 19mm, NO DRILL 7/8”
10 40
10 15
FOOTNOTES
74475
7/8” 3/4”, 13/16”, NO DRILL 7/8” 1/2”
STANDARD WIRE
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
12 40 10 20 n 41923 @,GP,SA, † 3/4”, 13/16”, NO DRILL
7/8”
1/2”
5
10 20 n 45010 #,TF
1/2”
HJ
13, 18, 19mm, NO DRILL 7/8”
5
10 45
74475
78058
BN,HJ
85253
n 37084 Ø,CP,DS,GU 7/8”, 15/16” NO DRILL
5
10 20
–
78058
–
–
n 33072 Ø,CP,DS,GU 3/4”, 15/16” NO DRILL
5
8
20 n 41929 @, DY, GP, KL, SG, †
3/4”, 13/16”, 1/2” 15/16”
12
15 35 –
78058
–
–
l 44536 Ø,CP,DY
3/4”, 7/8”
NO DRILL
6
10 25 n 96929 @, DY, GP,
n 44603 Ø,CP,DS
3/4”, 1-1/8” NO DRILL
n 33072 Ø,CP,GU
78058
–
85253
78058
–
85253
78058
–
85253
78058
–
85253
1/2”
12
15 35
6
KL, SG 10 20 n 45288 #,DY,KL,SB
1/2”
12
14 35
3/4”, 15/16” NO DRILL
5
8
1/2”
12
15 35 –
l 44536 Ø,CP
3/4”, 7/8”
NO DRILL
6
10
1/2”
12
15 35
n 44603 Ø,CP
3/4”, 1-1/8” NO DRILL
6
10
1/2”
12
14 35
9/16”
18
18 95
1/2”
12
15 35 –
1/2”
12
15 35
1/2”
12
14 35
9/16”
18
18 95
1/2”
12
15 35 –
3/4”, 13/16”, 1/2” 15/16” 3/4”, 13/16”, 1/2” 15/16”
12
15 35
12
14 35
n 33072 Ø,CP,GU
3/4”, 15/16” NO DRILL
5
8
l 44536 Ø,CP
3/4”, 7/8”
NO DRILL
6
10
n 44603 Ø,CP
3/4”, 1-1/8” NO DRILL
6
10
3/4”, 13/16”, 15/16” 3/4”, 13/16”, 15/16” 20 n 41929 @, GP, KL, 3/4”, 13/16”, SG, † 15/16” 3/4”, 13/16”, 25 n 96929 @, GP, KL, SG 15/16” 20 n 45288 #,KL,SB 3/4”, 13/16”, 15/16” n 45299 #, AA, CS, FS, 16, 18, 21mm, GH, HM, LT, 3/8” 20 n 41929 @, GP, KL, 3/4”, 13/16”, SG, † 15/16” 3/4”, 13/16”, 25 n 96929 @, GP, KL, SG 15/16” 20 n 45288 #,KL,SB 3/4”, 13/16”, 15/16” n 45299 #, AA, CS, FS, 16, 18, 21mm, GH, HM, LT, 3/8” 20 n 41929 @, GP, KL, 3/4”, 13/16”, SG, † 15/16”
n 33072 Ø,CP,GU
3/4”, 15/16” NO DRILL
5
8
l 44536 Ø,CP
3/4”, 7/8”
NO DRILL
6
10 25 n 96929 @, GP,
n 44603 Ø,CP
3/4”, 1-1/8” NO DRILL
6
KL, SG 10 20 n 45288 #,KL,SB
n 33072 Ø,CP,GU
3/4”, 15/16” NO DRILL
5
8
l 44536 Ø,CP n 44603 Ø,CP
3/4”, 7/8”
3/4”, 1-1/8” NO DRILL
6 6
10 25 10 20
NO DRILL
20
–
n 45288 #,KL,SB
06996
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE 7.5 12 30 7 12 40
74475
n 51143 Ø,CP,GU
04-05 Pickup, Ram, Full Size 1500, Except Daytona, Hemi Sport Quad Cab, Ram Rumble Bee & SRT-10
3/4”
7/16", 1/2" 30
n 51143 Ø,CP,DS,GU 3/4”, 15/16” NO DRILL
03-05
DRILL BITS
10 15
n 37081 CQ
03-05
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME 5
1/2”
n 37081 CQ
n 51017 GP,FP
Pickup, Ram, Full Size 1500, Except Mega Cab & SRT-10
15/16", 3/4” 5/8”
74475
n 51016 HM,FP
Pickup, Ram, Full Size 3500 HD
n 37017 †,GU l 37034 GU
7/16", 1/2" 30
Pickup, Ram, Full Size 2500 Only, w/ 2002 Deep Drop Bumper 2002 Pickup, Ram, Full Size 3500 Only
Pickup, Ram, Full Size 2500 HD
7.5 40 6.5 45
5
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
3/4”, 13/16”, 1/2” 15/16”
12
14 35
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
15, 18, 21mm, 9/16", 11/16", 3/4", T50
DRILL BITS
9/16”, 3/4” 1/2”
n 51017 GP,FP n 88001 GU
WRENCHES
FOOTNOTES
HITCH NUMBER
l 37069 GU n 37096 JL
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Pickup, Ram, Full Size 2500 Only
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
135
DODGE
DODGE
134
REESE TOWPOWER
REESE TOWPOWER
Pickup, Ram, Full Size 3500 HD Chassis Cab
3/4”, 15/16” NO DRILL
n 51143 Ø,CP,GU
3/4”, 15/16” NO DRILL
6
10 20
8 20
12
15 35
n 45288 #,KL,SB
3/4”, 13/16”, 1/2” 15/16”
12
3/4”, 13/16”, 1/2” 15/16” 3/4”, 13/16”, 1/2” 15/16” 16, 18, 21mm, 9/16” 3/8” 3/4”, 13/16”, 1/2” 15/16”
n 33072 Ø,CP,GU
3/4”, 15/16” NO DRILL
5
8
20 n 41929 @, GP, KL,
l 44536 Ø,CP
3/4”, 7/8”
NO DRILL
6
10 25 n 96929 @, GP,
n 44603 Ø,CP
3/4”, 1-1/8” NO DRILL
6
SG, †
KL, SG 10 20 n 45299 #, AA, CS, FS, GH, HM, LT, n 45288 #,KL,SB
n 33072 Ø,CP,GU
3/4”, 15/16” NO DRILL
5
8
l 44536 Ø,CP
3/4”, 7/8”
NO DRILL
6
10 25 n 96929 @, GP,
n 44603 Ø,CP
3/4”, 1-1/8” NO DRILL
6
07-12
20 n 41929 @, GP, KL, SG, †
KL, SG 10 20 n 45299 #, AA, CS, FS, GH, HM, LT, n 41936 @
n 96936 @ n 41940 @, † n 96940 @ n 96947 @ Pickup, Ram, Full Size 4500 HD Chassis Cab
n 41936 @, †
08-12
n 96936 @ n 41940 @, † n 96940 @ n 96947 @ Pickup, Ram, Full Size 5500 HD Chassis Cab
n 41936 @, †
08-12
n 96936 @ n 41940 @, † n 96940 @ n 96947 @ Pickup, Ram, Full Size 1500 Only
n 44603 Ø,CP
2009
6
78058
–
85253
14 35 –
78058
–
85253
12
15 35 –
–
–
85253
12
15 35
18
18 95
12
14 35 –
–
–
85253
3/4”, 13/16”, 1/2” 15/16”
12
15 35 –
78058
–
85253
3/4”, 13/16”, 1/2” 15/16” 16, 18, 21mm, 9/16” 3/8” 3/4” 17/32”
12
15 35
18
18 95 78058
–
85253
–
–
–
12
30 –
3/4”
17/32”
21mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21, 24mm, 13/16”, 7/8” 3/4”
9/16”
12 15
30 16 35
9/16”
15
16 35 –
11/16”
15
16 35 –
17/32”
12
30 –
3/4”
17/32”
21mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21, 24mm, 13/16”, 7/8” 3/4”
9/16”
12 15
30 16 35
9/16”
15
16 35 –
11/16”
15
16 35 –
17/32”
12
30 –
17/32”
12 15
30 16 35
15
16 35 –
15
16 35 –
3/4”
21mm, 9/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8” 21, 24mm, 11/16” 13/16”, 7/8”
10 20
–
78058
–
85253
–
–
–
–
–
–
85253
–
–
–
–
– – 74682, 78058 85262 78071 N/A
– BO
85253 85219
Pickup, Ram, Full Size 1500 Only
09-13
Pickup, Ram, Full Size 2500 HD, Except Mega Cab Pickup, Ram, Full Size 2500 HD, Inc. Mega Cab
10-12
n 45288 #,KL,SB
3/4”, 13/16”, 1/2” 15/16”
12
14 35 –
–
Fifth Wheel – models only –
10-12
n 41929 @, GP, KL,
3/4”, 13/16”, 1/2” 15/16”
12
15 35 –
–
–
–
n 96929 @, GP,
3/4”, 13/16”, 1/2” 15/16” 16, 18, 21mm, 9/16” 3/8” 3/4”, 13/16”, 1/2” 15/16”
12
15 35
18
18 95
10-12
KL, SG n 45299 #, AA, CS, FS, GH, HM, LT, n 45288 #,KL,SB
12
14 35 –
–
–
–
10-12
n 41929 @, GP, KL,
3/4”, 13/16”, 1/2” 15/16”
12
15 35 –
–
–
–
3/4”, 13/16”, 1/2” KL, SG 15/16” n 45299 #, AA, CS, FS, 16, 18, 21mm, 9/16” GH, HM, LT, 3/8”
12
15 35
18
18 95
Pickup, Ram, Full Size 3500 HD, Except Mega Cab Pickup, Ram, Full Size 3500 HD, Inc. Mega Cab
n 44603 Ø,CP
3/4”, 1-1/8” NO DRILL
OEM REPLACE.
3/4”, 1-1/8” NO DRILL
5
3/4”, 13/16”, 1/2” 15/16”
FOOTNOTES
n 44603 Ø,CP
06-09 06-09
KL, SG
STANDARD WIRE
10 25 n 96929 @, GP,
T-CONNECTOR
6
DRILL BITS
NO DRILL
SG, †
WRENCHES
3/4”, 7/8”
8 20
15 35 –
FOOTNOTES
l 44536 Ø,CP
5
WT. DISTRIB. INSTALL TIME
n 51143 Ø,CP,GU
12
20 n 41929 @, GP, KL,
06-09 06-09
3/4”, 13/16”, 1/2” 15/16”
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE 8
DRILL BITS
5
WRENCHES
3/4”, 15/16” NO DRILL
FOOTNOTES
STYLE
n 33072 Ø,CP,GU
HITCH NUMBER
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
5
8 20
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
3/4”, 1-1/8”
6
10 20
SG, †
SG, †
n 96929 @, GP,
Pickup, Ram, Full Size 1500 Only
10-13
06996
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
3/4”, 1-1/8” NO DRILL all6 safety – n 44603 Ø,CP 10 20precautions when working beneath a vehicle and – eye –wear protection. – IMPORTANT: Observe
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
Pickup, Ram, Full Size 3500 HD, Except Mega Cab Pickup, Ram, Full Size 3500 HD, Inc. Mega Cab
3/4”, 15/16” NO DRILL
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
n 51143 Ø,CP,GU
06-08
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
WT. CARRYING
Pickup, Ram, Full Size 2500 HD, Except Mega Cab Pickup, Ram, Full Size 2500 HD, Inc. Mega Cab
YEAR
MODEL
Pickup, Ram, Full Size 1500, Inc. Mega Cab
APPLICATIONS GUIDE
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
137
DODGE
DODGE
136
REESE TOWPOWER
REESE TOWPOWER
Ramcharger All, Except w/Skid Shield 74-85 Ramcharger w/Deep Drop Bumper, 74-85 Except w/Skid Shield 82-85 Ramcharger
n 37042 –
n 88001 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
6
1/4”, 1/2”, 5 9/16”
6
OEM REPLACE.
FOOTNOTES
STANDARD WIRE
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
T-CONNECTOR – –
78058 78058
–
– –
–
78058
–
–
74182 74182
78058 78058
BN BN
– –
74182
78508
BN
–
–
78104
–
–
–
74051
n 37152 –
n 37042 –
n 06097 –
10 45
30
n 37081 M,TH
15, 18, 21mm, 9/16", 11/16", 3/4", T50 13mm, 9/16”, 11/16”
5
7/16", 1/2" 30
Ramcharger All, Except w/Skid Shield 86-88 Ramcharger w/Deep Drop Bumper, 86-88 Except w/Skid Shield 86-93 Ramcharger
n 88001 –
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
1/4”, 1/2”, 5 9/16”
13, 18, 19mm, NO DRILL 7/8”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6
13, 18, 19mm, NO DRILL 7/8”
5
10 45
30
7/16", 1/2" 30
74182
Spirit
89-95
Sprinter All 41 Wide Frames, Except 118 Wheelbase & Factory Metal Step Platform Sprinter 144 & 170 Wheelbase Models Only, Except w/Factory Step Bumper Sprinter w/Factory Step Bumper Sprinter 144 & 170 Wheelbase Models Only, Except w/Factory Step Bumper Sprinter w/Factory Step Bumper Stratus 4 Dr. Only
03-06
n 33089 Ø
18mm, 3/4”
NO DRILL
5
7.5 20
–
78104
–
–
2007
n 44576 Ø,HM
18, 19mm
NO DRILL
6
7.5 20
–
–
–
–
2007 08-09
n 44576 Ø,HM n 44576 Ø,HM
18, 19mm
NO DRILL NO DRILL
5 6
7.5 30 7.5 20
– –
– –
–
18, 19mm
–
– –
08-09 95-00
n 44591 Ø,HM
18, 19mm
NO DRILL
5
7.5 30
– –
– 78013
–
– –
Stratus 2 Dr. Only
01-02
–
–
–
–
Stratus 4 Dr. Only
01-06
–
78013
–
–
Van, B-Series Full Size
71-77
–
78058
–
–
Van, B-Series Full Size
78-85
10
12 35 –
78058
–
–
10
12 35 –
–
–
–
NO DRILL
10
12 35 –
78058
–
–
NO DRILL
10
12 35 –
–
–
–
NO DRILL
10
12 35 74430
78058
BN
–
NO DRILL
10
12 35 74430
–
BN
–
78058
BN
–
n 06977 JR n 77088 JR,KH
12, 13, 14mm, 11/16”
1/2”
13, 16, 17mm, 3/4”, 9/16”, 11/16”
3/8”
1/2”
40
40
30 06977 JR
13, 16, 17mm, 3/4”, 9/16”, 11/16”
1/2”
40 n 51037 Ø,DG
5/8”, 11/16”, NO DRILL 3/4”, 7/8”
5
10 30
n 44094 Ø,BF,DG
5/8”, 11/16”, NO DRILL 3/4”, 7/8”
5
10 30 n 41910 Ø,@, † n 96910 Ø,@
n 51037 Ø,DG Van, B-Series Full Size
Van, B-Series Full Size
Van, B-Series Full Size
n 51037 Ø,DG
86-92
n 51037 Ø,DH
1993
n 06962 Ø,DH
94-97
3/4”, 7/8”
NO DRILL
5/8”, 11/16”, NO DRILL 3/4”, 7/8” 5/8”, 11/16”, NO DRILL 3/4”, 7/8”
5/8”, 11/16”, NO DRILL 3/4”, 7/8”
5
10 30
n 44094 Ø,BF,DG
5
10 30
n 44094 Ø,BF
5
10 30
n 44094 Ø,BF
n 33009 Ø,BF n 36072 Ø,†,BF,DV n 37070 Ø,BF
15
5/8”, 11/16”, NO DRILL 3/4”, 7/8” 5/8”, 11/16”, NO DRILL 3/4”, 7/8”
5/8”, 11/16”, NO DRILL 3/4”, 7/8”
3/4”, 7/8”
NO DRILL
3/4”
NO DRILL
3/4”, 7/8”
NO DRILL
5
10 30
5
10 30 n 41910 Ø, @, DH,
5
5 5 6
HM, † n 96910 Ø, @, DH, HM 10 30 n 41910 Ø, @, DH, HM, † n 96910 Ø, @, DH, HM
74430
HM, † n 96910 Ø, @, DH, HM
06996
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
5/8”, 11/16”, NO DRILL 3/4”, 7/8”
5
10 30
n 44094 Ø,BF
5/8”, 11/16”, NO DRILL 3/4”, 7/8”
5
5/8”, 11/16”, 3/4”, 7/8” 5/8”, 11/16”, 3/4”, 7/8” 5/8”, 11/16”, 3/4”, 7/8” 5/8”, 11/16”, 3/4”, 7/8”
7.5 20 10 45 10 25 n 41910 Ø, @, DH,
n 51037 Ø,DH
5/8”, 11/16”, NO DRILL 3/4”, 7/8” 5/8”, 11/16”, NO DRILL 3/4”, 7/8”
5/8”, 11/16”, NO DRILL 3/4”, 7/8” 5/8”, 11/16”, NO DRILL 3/4”, 7/8”
–
10
12 35 74430
–
BN
–
10
12 35 74430
–
BN
–
10 30
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
WRENCHES
FOOTNOTES
HITCH NUMBER
n 37081 M,TH n 37152 –
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
139
DODGE
DODGE
138
REESE TOWPOWER
REESE TOWPOWER
n 06962 Ø,BF
99-00
3/4”, 7/8”
NO DRILL
APPLICATIONS GUIDE
EAGLE FIAT
n 06962 Ø,BF
01-03
n 06354 JR,TA
93-97
2012
Aerostar Van Extended Body
86-96
3/4”, 7/8”
NO DRILL
5/8”, 11/16”, NO DRILL 3/4”, 7/8”
5
10 30
15
n 77255 Ø,GP,JR
7/8”, M8, M13
NO DRILL
13, 15mm, 9/16”, 1/8”, 3/8”, 11/16”, 7/8” 1/2”
n 44094 Ø
3/4”, 7/8”
NO DRILL
5/8”, 11/16”, NO DRILL 3/4”, 7/8”
10 30
5 6
7.5 20 10 25
n 06033 J,GP
11/16”, 3/4”
Aerostar Van Standard Body
86-96
n 06033 GP,HC
15, 18, 21mm, 9/16", 11/16", 3/4", T50 11/16”, 3/4”
Aerostar Van Extended Body
1997
n 06033 J,GP
11/16”, 3/4”
1/2”
30 n 37152 –
n 88001 –
Bronco Full Size
78-79
10 30
n 06033 GP,HC
15, 18, 21mm, 9/16", 11/16", 3/4", T50 11/16”, 3/4”
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6
78-79
Bronco Full Size
80-81
5/8”, 11/16”, NO DRILL 3/4”, 7/8”
n 44615 †,J
1/2”
30
1/2”
30 n 37152 –
7.5 20 10 25 10 30
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6
11/16”, 3/4” 1/4”, 7/16”, 3.5 6 1/2”, 1”
40
OEM REPLACE.
FOOTNOTES
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
–
n 41910 Ø,@,HM, † 5/8”, 11/16”, NO DRILL
10
12 35 74430
–
BN
–
n 96910 Ø,@,HM
10
12 35 74430
–
BN
–
78058
BN
–
3/4”, 7/8” 5/8”, 11/16”, NO DRILL 3/4”, 7/8”
74888 n 41910 Ø,@,HM, † 5/8”, 11/16”, NO DRILL
10
12 35 74888
–
BN
–
n 96910 Ø,@,HM
3/4”, 7/8” 5/8”, 11/16”, NO DRILL 3/4”, 7/8”
10
12 35 74888
–
BN
–
n 41910 Ø,@,HM, † 5/8”, 11/16”, NO DRILL
10
12 35 85253
78058
BN,RD
–
n 96910 Ø,@,HM
10
12 35 85253
–
BN
–
85253
78058
BN,RD
–
–
–
–
–
85769
78104
BN,CH
–
–
78013
–
–
–
78013
–
–
74665
78058
BN
–
3/4”, 7/8” 5/8”, 11/16”, NO DRILL 3/4”, 7/8”
40
7/16", 1/2" 50 1/2”
BN
74672
30
74051 n 44615 †,J
40
74665
78058
BN
–
n 36025 n 44108
30 45
–
78058
–
–
–
78058
–
–
74426
78058
BN
–
74426
78058
BN
–
11/16”, 3/4” 1/4”, 7/16”, 3.5 6 1/2”, 1” FP 3/4” 1/2” 7.5 12 FP,GU, 18mm, 3/4” 1/2” 6 10 HM,HX deep socket FP,GP, GU,HX 18mm, 3/4” 1/2” 6 10 deep socket – 3/4” 1/2” 5 8
n 36025 n 37081 M
n 36025 FP n 44108 FP,GU,
13, 18, 19mm, NO DRILL 7/8” 3/4” 1/2”
18mm, 3/4” HM,HX deep socket n 44109 FP,GP, GU,HX 18mm, 3/4” deep socket 3/4” n 36025 – 13, 18, 19mm, n 37081 M 7/8”
80-86 06996
5 6 5
78058
40
n 44109 Bronco Full Size w/Deep Drop Bumper
NO DRILL NO DRILL
7/16", 1/2" 50
n 37042 –
1997
5
3/4”, 7/8” 3/4”, 7/8”
74430
10 30
30
n 88001 –
Aerostar Van Standard Body
5/8”, 11/16”, NO DRILL 3/4”, 7/8”
n 33009 Ø,BF n 37070 Ø,BF n 44094 Ø
FOOTNOTES
7.5 20 10 25
5
5
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
5/8”, 11/16”, NO DRILL 3/4”, 7/8” 3/4”, 7/8” NO DRILL
5 6
40
n 37042 –
Bronco Full Size w/Deep Drop Bumper
FOOTNOTES
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
STYLE
n 44094 Ø
NO DRILL NO DRILL
01-03
500, All, Inc. 500c (Cabrio)
FORD
10 30
n 33009 Ø,BF n 37070 Ø,BF
n 51037 Ø
Vision
5
3/4”, 7/8” 3/4”, 7/8”
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
5
45
30 10 45
1/2”
7.5 12 30 6 10 45
1/2”
6
10 45
1/2”
5 5
8 30 10 45
NO DRILL
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
Van, Ram Full Size
5/8”, 11/16”, NO DRILL 3/4”, 7/8”
15
n 51037 Ø Van, Ram All, Except 109.3 Wheelbase
WRENCHES
n 33009 Ø,BF n 37070 Ø,BF
15
n 51037 Ø Van, Ram Full Size
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
DRILL BITS NO DRILL
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
STANDARD WIRE
3/4”, 7/8”
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
T-CONNECTOR
n 06962 Ø,BF
1998
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Van, B-Series Full Size
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
141
DODGE - FORD
DODGE - FORD
140
REESE TOWPOWER
REESE TOWPOWER
n 37042 –
Bronco Full Size
n 37042 –
Bronco Full Size
n 37042 –
Bronco II
n 37042 –
C-Max, All Styles Contour All, Except SVT Crown Victoria / LTD
2013 95-00 75-91
n 77284 GP,JR,KH n 77009 –
06996
13mm, 11/16”
1/2”
13mm, 3/4”
1/2”
6
10 45
n 44109 FP,GP, GU,HX 18mm, 3/4” 1/2”
6
10 45
n 36025 –
5
8
deep socket 3/4”
1/2”
–
78058
–
–
78058
–
–
78058
–
–
78104
–
–
78058 78058
– –
– –
OEM REPLACE.
BN
FOOTNOTES
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
STYLE
1/2”
78058
30
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6
30
n 36025 FP
3/4”
1/2”
7.5 12 30
n 44108 FP,GU,
18mm, 3/4” deep socket
1/2”
6
10 45
n 44109 FP,GP, GU,HX 18mm, 3/4” 1/2”
6
10 45
n 36025 –
5
8
HM,HX
deep socket 3/4”
1/2”
–
30
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6
40
n 36025 FP
3/4”
1/2”
7.5 12 30
n 44108 FP,GU,
18mm, 3/4” deep socket
1/2”
6
10 45
n 44109 FP,GP, GU,HX 18mm, 3/4” 1/2”
6
10 45
n 36025 –
5
8
HM,HX
deep socket 3/4”
1/2”
74669
30
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6
30
n 36025 FP
3/4”
1/2”
7.5 12 30
n 44108 FP,GU,
18mm, 3/4” deep socket
1/2”
6
10 45
n 44109 FP,GP, GU,HX 18mm, 3/4” 1/2”
6
10 45
n 36025 –
5
8
HM,HX
deep socket 3/4”
1/2”
74669
30 74669
n 37152 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
7/16", 1/2" 35
84-90
n 88001 –
18mm, 3/4” deep socket
HM,HX
74426
74669 n 37152 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
n 44108 FP,GU,
7/16", 1/2" 35
94-96
n 88001 –
7.5 12 30
74051 n 37152 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
30
1/2”
7/16", 1/2" 35
92-93
n 88001 –
6
3/4”
74426 n 37152 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
1/4”, 1/2”, 5 9/16”
n 36025 FP
7/16", 1/2" 30
87-91
n 88001 –
6
7/16", 1/2" 30
25 30
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6
–
30
74203
– –
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
Bronco Full Size
15, 18, 21mm, 9/16", 11/16", 3/4", T50
1/4”, 1/2”, 5 9/16”
STANDARD WIRE
n 88001 –
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW T-CONNECTOR
n 37042 –
FOOTNOTES
HITCH NUMBER
n 37152 –
82-86
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Bronco Full Size
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
143
FORD
FORD
142
REESE TOWPOWER
REESE TOWPOWER
E-150 Econoline Van Full Size, All Models
E-150 Econoline Van Full Size, All Models
E-150 Econoline Van Full Size, All Models
E-150 Econoline Van Full Size, All Models
3/4”, 7/8”
1/2”
75-91
n 88002 –
3/4”
1/2”
30 n 51007 HM, HX, O, PA, T
3/4”, 7/8”
1/2”
95-96
97-03
n 06127 Ø,EF,HM
3/4”, 7/8”
NO DRILL
20 n 51007 HM, HX, O,
3/4”, 7/8”
n 88002 –
3/4”
1/2”
30 l 37051 – n 37041 – 20 n 51007 HM, HX, O,
3/4”, 7/8”
1/2”
n 06127 Ø,EF,HM
3/4”, 7/8”
NO DRILL
n 88002 –
3/4”
1/2”
n 06127 Ø,EF,HM
3/4”, 7/8”
NO DRILL
n 88002 –
3/4”
1/2”
00-03
n 88002 –
04-07
PA, T
3/4”
1/2”
PA, T
PA, T
30 l 37051 – n 37041 – 20 n 51007 HM, HX, O, PA, T
30 l 37051 – n 37041 – l 51094 Ø,RT
30 l 51094 Ø,RT
2008
n 88002 –
2009
E-250 Econoline Van Full Size, All Models
E-250 Econoline Van Full Size, All Models
3/4”
1/2”
1/2”
1/2”
5 5 5
6 20 6 20 10 30
5 5 6
6 20 6 20 8 15
1/2”
3/4”
1/2”
3/4”
1/2”
3/4”
NO DRILL
l 37041 – 30 l 51094 Ø,RT
30
75-91
n 88002 –
3/4”
1/2”
30 n 51007 HM, HX, O,
3/4”, 7/8”
1/2”
6
10 20 n 96906 @,HM,HY
13/16”, 7/8” 9/16”
10
12 30 74664
–
HG
–
n 44027 HX,O,PA,T
3/4”, 7/8”
1/2”
5
10 30 n 41906 @,HM,HY, † 13/16”, 7/8” 9/16”
10
12 30 74665
78058
–
–
l 44652 CS,HM
3/4”, 7/8”
1/2”
6
10 20 n 96906 @,HM,HY
13/16”, 7/8” 9/16”
10
12 30 74665
–
BN
–
n 44027 HX,O,PA,T
3/4”, 7/8”
1/2”
5
10 30 n 41906 @,HM,HY, † 13/16”, 7/8” 9/16”
10
12 30 74665
78058
BN
85219
l 44652 CS,HM
3/4”, 7/8”
1/2”
6
10 20 n 96906 @,HM,HY
10
12 30 74665
–
BN
–
l 44532 Ø
3/4”
NO DRILL
6
8
15 n 41926 Ø,@,HM, † 13/16”, 7/8” NO DRILL
10
12 30 74665
78058
BN
85219
n 96926 Ø,@,HM 13/16”, 7/8” NO DRILL n 96945 Ø,@,HM 13/16”, 7/8” NO DRILL 15 n 41906 @,HM,HY, † 13/16”, 7/8” 9/16”
10 12 30 74665 10 12 30 74665 10 12 30 –
BN
–
78058
–
–
10 12 30 10 12 30 10 12 30 – 10 12 30 – 10 12 30 85774
– – 78058
– – CH
– – 85219
–
CH
–
1/2”
6
10 20 n n n n n
20
PA, T
1/2”
5
6
3/4”
1/2”
3/4”
NO DRILL
5 6
6 20 8 15
3/4”, 7/8”
1/2”
n 88002 –
3/4”
1/2”
30 l 37051 – l 37041 – 20 n 51007 HM, HX, O,
3/4”, 7/8”
1/2”
30 l 37051 – l 37041 –
3/4”
1/2”
3/4”
1/2”
PA, T
PA, T
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
5
l 44532 Ø l 44652 CS,HM
3/4”
NO DRILL
3/4”, 7/8”
1/2”
6 6
96906 41926 96926 96945 41906
@,HM,HY
1/2”
5
10 30
3/4”
1/2”
3/4”
1/2”
5 5 5
6 20 6 20 10 30
5 5
6 6
20 20
13/16”, 7/8” 9/16”
13/16”, 7/8” 9/16”
Ø,@,HM, † 13/16”, 7/8” NO DRILL Ø,@,HM
13/16”, 7/8” NO DRILL
Ø,@,HM
13/16”, 7/8” NO DRILL
@,HM,HY
13/16”, 7/8”, †
8 15 n 96906 @,HM,HY 10 20 n 41926 Ø,@,HM
9/16”
13/16”, 7/8” 9/16” 13/16”, NO DRILL 7/8”, † 13/16”, 7/8” NO DRILL 13/16”, 7/8” NO DRILL 13/16”, 7/8” NO DRILL
n 41906 @,HM,HY, † 13/16”, 7/8” 9/16”
20
10 30
OEM REPLACE.
l 44652 CS,HM
3/4”, 7/8”
3/4”
FOOTNOTES
–
l 44652 CS,HM
6 20 8 15
WT. DISTRIB. INSTALL TIME
–
6 6
5 6
WT. CARRYING
78013
5 5
1/2”
DRILL BITS
12 30 74664
1/2”
NO DRILL
WRENCHES
10
1/2”
3/4”
FOOTNOTES
10 30 n 41906 @,HM,HY, † 13/16”, 7/8” 9/16”
3/4”
3/4”
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
5
3/4”
3/4”, 7/8”
1/2”
1/2”
8
20 n 51007 HM, HX, O,
3/4”
3/4”, 7/8”
6
NO DRILL
n 88002 –
10 20
NO DRILL
6
–
6
3/4”
5
–
1/2”
l 44532 Ø
1/2”
78058
3/4”, 7/8”
8 15 20 20
–
– – –
– –
HX, O, P n 44027 HX,O,PA,T
6
3/4”, 7/8”
NO DRILL
–
NO DRILL
3/4”
n 06127 Ø,EF,HM
3/4”, 7/8”
10 20 10 30
30
1/2”
n 06127 Ø,EF,HM
WT. CARRYING WT. DISTRIB. INSTALL TIME 6 20 6 20 10 30
3/4”, 7/8”
6 5
n 96926 Ø,@,HM n 96945 Ø,@,HM n 96945 Ø,@,HM
3/4”
06996
5 5 5
l 37041 – l 51094 Ø,RT
n 88002 –
95-96
1/2” 1/2”
3/4”
10-12
92-94
3/4”
1/2”
1/2” 1/2”
l 44652 CS, HM,
3/4”
1/2”
3/4”, 7/8” 3/4”, 7/8”
10 30
l 44652 CS, HM, HX, O, P n 44027 HX,O,PA,T
10 30
3/4”
10 30
3/4”, 7/8”
5
3/4”
5
78058 78013 78058
n 44027 HX,O,PA,T
1/2”
l 37051 –
l 37051 –
3/4”
5
1/2”
74428 – –
10 30
30
09-12 n 88002 –
E-150 Econoline Van Full Size, All Models E-250 Econoline Van Full Size, All Models
3/4”
5
STANDARD WIRE
30 n 51007 HM, HX, O,
n 88002 –
E-150 Econoline Van Full Size, All Models E-150 Econoline Van Full Size, All Models
DRILL BITS
1/2”
l 37051 – n 37041 –
E-150 Econoline Van Full Size, All Models
WRENCHES
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
3/4”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
l 44532 Ø l 44652 Ø,CS,HM
3/4”
NO DRILL
3/4”, 7/8”
1/2”
6 6
8 15 n 10 20 n n n
n 44027 HX,O,PA,T
3/4”, 7/8”
1/2”
5
10 30
l 44652 CS, HM,
96906 41926 96926 96945
@,HM,HY
13/16”, 7/8” 9/16”
Ø,@,HM, † 13/16”, 7/8” NO DRILL Ø,@,HM
13/16”, 7/8” NO DRILL
Ø,@,HM
13/16”, 7/8” NO DRILL
10 10
12 30 85774 12 30
–
BN
10 12 30 10 12 30 10 12 30 85774 10
12 30 85774
10 12 10 12 10 12 10 12
30 30 30 30
CH
78058
CH
85219
85774 85774 85774 85774
– – –
CH CH
– – –
–
78058
–
–
CH CH
HX, O, P n 44027 HX,O,PA,T
3/4”, 7/8”
1/2”
6
10 20
3/4”, 7/8”
1/2”
5
10 30 n 41906 @,HM,HY, † 13/16”, 7/8” 9/16”
10
12 30 74664
78013
–
–
l 44652 CS,HM
3/4”, 7/8”
1/2”
6
10 20 n 96906 @,HM,HY
13/16”, 7/8” 9/16”
10
12 30 74664
–
HG
–
n 44027 HX,O,PA,T
3/4”, 7/8”
1/2”
5
10 30 n 41906 @,HM,HY, † 13/16”, 7/8” 9/16”
10
12 30 74665
78058
–
–
l 44652 CS,HM
3/4”, 7/8”
1/2”
6
10 20 n 96906 @,HM,HY
10
12 30 74665
–
BN
–
13/16”, 7/8” 9/16”
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
E-150 Econoline Van Full Size, All Models
n 88002 –
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
92-97 98-07 75-83
92-94
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
T-CONNECTOR
E-150 Econoline Van Full Size, All Models
YEAR
MODEL
Crown Victoria / LTD Crown Victoria / LTD E-100 Econoline Van Full Size, All Models
APPLICATIONS GUIDE
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
145
FORD
FORD
144
REESE TOWPOWER
REESE TOWPOWER
E-250 Econoline Van Full Size, All Models
T-CONNECTOR
STANDARD WIRE
BN
85219
3/4”
1/2”
6 20 6 20 8 15
3/4”, 7/8”
1/2”
6
10 20 n 96906 @,HM,HY
10
12 30 74665
–
BN
–
1/2”
5 5 6
l 44652 CS,HM
3/4”
l 44532 Ø
3/4”
NO DRILL
6
8
74665
78058
BN
85219
12 30 74665
78058
BN
85219
BN
–
3/4”
NO DRILL
DRILL BITS
30 l 37051 – l 37041 – l 51094 Ø,RT
HITCH NUMBER
1/2”
DRILL BITS
3/4”
WRENCHES
n 88002 –
15 n 41926 Ø,@,HM, † 13/16”, 7/8” NO DRILL
04-07
l 44652 CS,HM
3/4”, 7/8”
1/2”
6
n 96926 Ø,@,HM 13/16”, 7/8” NO DRILL n 96945 Ø,@,HM 13/16”, 7/8” NO DRILL 10 20 n 41906 @,HM,HY, † 13/16”, 7/8” 9/16”
l 44532 Ø
3/4”
NO DRILL
6
8
n 96906 @,HM,HY n 88002 –
3/4”
1/2”
30 l 51094 Ø,RT l 37051 – n 37041 –
NO DRILL
6
8 15
3/4”
1/2”
3/4”
1/2”
5 5
6 6
3/4”
2008
l 44652 CS,HM
3/4”, 7/8”
1/2”
6
n 96926 Ø,@,HM 13/16”, 7/8” NO DRILL n 96945 Ø,@,HM 13/16”, 7/8” NO DRILL 10 20 n 41906 @,HM,HY, † 13/16”, 7/8” 9/16”
l 44532 Ø
3/4”
NO DRILL
6
8
n 96906 @,HM,HY n 88002 –
3/4”
1/2”
30 l 51094 Ø,RT l 37051 – n 37041 –
NO DRILL
6
8 15
3/4”
1/2”
3/4”
1/2”
5 5
6 6
3/4”
09-12
3/4”
1/2”
30 l 51094 Ø,RT l 37051 – n 37041 –
NO DRILL
6
8 15
3/4”
1/2”
3/4”
1/2”
5 5
6 6
3/4”
n 88002 –
3/4”
1/2”
30 n 51007 HM, HX, O, PA, T
3/4”, 7/8”
1/2”
5
n 06127 Ø,EF,HM
92-94
3/4”, 7/8”
NO DRILL
20 n 51007 HM, HX, O, PA, T
l 37051 – n 37041 – n 88002 – E-350 Econoline Van Full Size, All Models
95-96
3/4”
1/2”
– –
– –
12 30 –
78058
–
–
–
–
–
78058
CH
85219
12 30 85774 85774
– 78058
CH CH
– 85219
12 30 85774
78058
CH
85219
CH
–
10 12 30 – 10 12 30 10 12 30 85774 10
10
12 30 85774
78058
CH
85219
10
12 30 85774 85774
– 78058
CH CH
– 85219
12 30 85774
78058
CH
85219
CH
–
13/16”, 7/8” NO DRILL
l 44532 Ø
3/4”
NO DRILL
6
8
n 96906 @,HM,HY 15 n
13/16”, 7/8” 9/16”
CH CH
20 20
10 30
n 44027 HX,O,PA,T
3/4”, 7/8”
1/2”
5
10 30
l 44652 CS, HM,
3/4”, 7/8”
1/2”
6
10 20
1/2”
5
10 30
1/2” 1/2”
5 5
6 6
30 n 51007 HM, HX, O,
3/4”, 7/8”
1/2”
5
10 30
n 44027 HX,O,PA,T
3/4”, 7/8”
n 51007 HM, HX, O,
3/4”, 7/8”
1/2”
5
10 30
l 44652 CS,HM l 44652 CS,HM
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
– 78058
–
10 20 n 41906 @,HM,HY, † 13/16”, 7/8” 9/16”
3/4”
PA, T
12 30 – –
10 12 30 85774 10 12 30 85774 10 12 30 85774
13/16”, 7/8” NO DRILL 13/16”, 7/8” NO DRILL
6
3/4”
PA, T
06996
3/4”, 7/8”
–
n 96926 Ø,@,HM n 96945 Ø,@,HM n 96945 Ø,@,HM 1/2”
HX, O, P
E-350 Econoline Van Full Size, All Models
–
10
3/4”, 7/8”
10-12 75-91
78058
n 41926 Ø,@,HM, † 13/16”, 7/8” NO DRILL
l 44652 CS,HM
E-250 Econoline Van Full Size, 09-12 Inc. E-250 Super Wagon Cargo Van E-250 Econoline Van Full Size, All Models E-350 Econoline Van Full Size, All Models
BN
20 20
2009
n 88002 –
13/16”, 7/8” 9/16”
10
15
E-250 Econoline Van Full Size, 2008 Inc. E-250 Super Wagon Cargo Van
E-250 Econoline Van Full Size, 09-12 Except E-250 Super Wagon Cargo Van Models
10
–
20 20 n 41926 Ø,@,HM, † 13/16”, 7/8” NO DRILL
E-250 Econoline Van Full Size, 2008 Except E-250 Super Wagon Cargo Van Models
10 12 30 74665 10 12 30 74665 10 12 30 –
15
E-250 Econoline Van Full Size, 04-07 Inc. E-250 Super Wagon Cargo Van
E-250 Econoline Van Full Size, All Models E-250 Econoline Van Full Size, All Models
13/16”, 7/8” 9/16”
10
n 41926 Ø,@,HM, † 13/16”, 7/8” NO DRILL
10
n 96926 Ø,@,HM n 96945 Ø,@,HM
10 12 30 85774 10 12 30 85774
13/16”, 7/8” NO DRILL 13/16”, 7/8” NO DRILL
–
CH
74664
78013
–
–
74664
78013
–
–
– –
HG
–
78058
BN
–
20 20 1/2”
5
n 41906 @,HM,HY, † 13/16”, 7/8” 9/16” 10 30 n 96906 @,HM,HY 13/16”, 7/8” 9/16”
3/4”, 7/8”
1/2”
3/4”, 7/8”
1/2”
6 6
10 20 10 20
10 12 30 74664 10 12 30 74664 74665
–
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
E-250 Econoline Van Full Size, 04-07 Except E-250 Super Wagon Cargo Van Models
E-250 Econoline Van Full Size, All Models
13/16”, 7/8” 9/16”
OEM REPLACE.
WT. DISTRIB. INSTALL TIME
78058
FOOTNOTES
WT. CARRYING
12 30 74665
DRILL BITS
10
WRENCHES
10 30 n 41906 @,HM,HY, † 13/16”, 7/8” 9/16”
FOOTNOTES
WRENCHES
5
HITCH NUMBER
FOOTNOTES
1/2”
3/4”, 7/8”
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
STYLE
3/4”, 7/8”
20 n 51007 HM, HX, O,
DRILL BITS
WT. CARRYING WT. DISTRIB. INSTALL TIME
n 44027 HX,O,PA,T
WRENCHES
INSTALL TIME STYLE
10 30
NO DRILL
HITCH NUMBER
FOOTNOTES
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
5
3/4”, 7/8”
E-250 Econoline Van Full Size, 00-03 Except E-250 Super Wagon Cargo Van Models E-250 Econoline Van Full Size, 00-03 Inc. E-250 Super Wagon Cargo Van
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
1/2”
n 06127 Ø,EF,HM
PA, T
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
FOOTNOTES
97-03
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
E-250 Econoline Van Full Size, All Models
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
147
FORD
FORD
146
REESE TOWPOWER
REESE TOWPOWER
n 88002 – 97-03 E-350 Econoline Van Full Size, All Models E-350 Econoline Van Full Size, 97-03 Inc. Super Wagon
E-350 Econoline Van Full Size, All Models
E-350 Econoline Van Full Size, All Models
E-350 Econoline Van Full Size, All Models E-350 Econoline Van Full Size, All Models
1/2”
11-13
Escape
01-02
12 30 74665
–
BN
–
13/16”, 7/8” NO DRILL
10
12 30 74665
78058
BN
–
10 12 30 74665 10 12 30 74665 10 12 30 –
– – 78058
BN BN –
– – –
10 12 30 10 12 30 10 12 30 10 12 30 10 12 30
– – –
– – –
–
–
–
–
85774
78058
–
–
10 12 30 10 12 30 10 12 30 10 12 30 10 12 30
85774 85774 85774 85774 85774
– – –
CH CH
– – –
n 41906 @,HM,HY, † 13/16”, 7/8” 9/16” 10 30 n 96906 @,HM,HY 13/16”, 7/8” 9/16”
n 51007 HM, HX, O,
3/4”, 7/8”
1/2”
5
10 30
l 44652 CS,HM
3/4”, 7/8”
1/2”
6
10 20
1/2”
5
10 30
n 44027 HX,O,PA,T
3/4”, 7/8”
1/2”
5
10 30 n 41906 @,HM,HY, † 13/16”, 7/8” 9/16”
5 5 6
6 20 6 20 8 15
PA, T
1/2”
30 l 37051 – n 37041 – l 51094 Ø,RT
3/4”
1/2”
3/4”
1/2”
3/4”
NO DRILL
PA, T
l 51094 Ø,RT
3/4”
3/4”
NO DRILL
NO DRILL
6
6
l 51094 Ø,RT
3/4”
NO DRILL
6
OEM REPLACE.
10
5
FOOTNOTES
13/16”, 7/8” 9/16”
1/2”
WT. DISTRIB. INSTALL TIME
–
3/4”, 7/8”
WT. CARRYING
BN
DRILL BITS
78058
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
STYLE
12 30 74665
n 44027 HX,O,PA,T
l 51094 Ø,RT
8 15
8 15
n 96906 @,HM,HY l 44532 Ø
3/4”
NO DRILL
6
8 15
8
15 n 96945 Ø,@,HM
n 41926 Ø,@,HM, † 13/16”, 7/8” NO DRILL n 96926 Ø,@,HM 13/16”, 7/8” NO DRILL 15 n 41906 @,HM,HY, † 13/16”, 7/8” 9/16”
l 44532 Ø
3/4”
NO DRILL
6
8
l 44652 CS,HM
3/4”, 7/8”
1/2”
6
10 20 n n n n 8 15 n
96906 41926 96926 96945 41906
10 20 n n n n n
96906 41926 96926 96945 96945
l 44532 Ø
3/4”
NO DRILL
6
l 44652 CS,HM
3/4”, 7/8”
1/2”
6
l 44532 Ø
3/4”
NO DRILL
6
8
l 44652 CS,HM
3/4”, 7/8”
1/2”
6
10 20 n n n n
10-12
@,HM,HY
13/16”, 7/8” 9/16”
Ø,@,HM, † 13/16”, 7/8” NO DRILL Ø,@,HM
13/16”, 7/8” NO DRILL
Ø,@,HM
13/16”, 7/8” NO DRILL
@,HM,HY, † 13/16”, 7/8” 9/16” @,HM,HY
13/16”, 7/8” 9/16”
Ø,@,HM, † 13/16”, 7/8” NO DRILL Ø,@,HM
13/16”, 7/8” NO DRILL
Ø,@,HM
13/16”, 7/8” NO DRILL
Ø,@,HM
13/16”, 7/8” NO DRILL
15 n 41906 @,HM,HY, † 13/16”, 7/8” 9/16” 96906 41926 96926 96945
@,HM,HY
13/16”, 7/8” 9/16”
Ø,@,HM, † 13/16”, 7/8” NO DRILL Ø,@,HM
13/16”, 7/8” NO DRILL
Ø,@,HM
13/16”, 7/8” NO DRILL
10 12 30 74665 10 12 30 74665
10
12 30 85774
10 12 10 12 10 12 10 12
30 30 30 30
–
CH CH CH
78058
CH
85738
85774 85774 85774 85774
– – –
CH CH
– – –
CH CH
45 n 51200 CP,GP,JR,KH 5.5, 8mm,
1/2”
4
0
55
n 44567 Ø, CP, GP,
NO DRILL
3.5
45
85774
78058
CH
–
4
0
55
NO DRILL
3.5 3.5 4
45 45
74707 85742
78058 –
CH
1/2”
n n
NO DRILL
n 51200 CP,GP,JR,KH 5.5, 8mm,
CH
– –
NO DRILL
3.5 4
45
NO DRILL
3.5 5
35
74664
78013
HG,RW
–
3/4”
3/4”
n l 51142 Ø,RT,KH n 37152 KH n 37042 KH
10, 18mm, 11/16” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
NO DRILL
3.5 5 35
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6
l
5.5, 8mm, 3/4” JR, KH 44641 Ø,GP,JR,KH 5.5, 8mm, 3/4” 44658 Ø,GP,JR,KH 5.5mm or 7/32”, 8mm, 3/4” 44672 Ø,GP,JR,KH 8mm, 5.5mm (or 7/32”), 3/4” 10, 18mm, 33039 Ø,KH 11/16”
60
7/16", 1/2" 60
74664 l 51142 Ø,RT
2003
n 37152 KH n 37042 KH
06996
10
10 30
3/4”
15, 18, 21mm, 9/16", 11/16", 3/4", T50
–
5
n 88002 –
n 88001 –
BN
1/2”
3/4”, 7/8”
15, 18, 21mm, 9/16", 11/16", 3/4", T50
78058
3/4”, 7/8”
20 n 51007 HM, HX, O,
n 88001 KH
74665
30 n 51007 HM, HX, O,
09-12
Edge Sport
– –
20 20
2009
09-10 11-13
– BN
6 6
2008
Edge Sport Edge All, Except Sport Models
– –
5 5
NO DRILL
NO DRILL
–
1/2”
3/4”, 7/8”
5.5, 8mm, 3/4”
BN
1/2”
n 06127 Ø,EF,HM
n 06525 Ø,GP,JR,KH
78058
3/4”
04-07
07-10
74665
3/4”
PA, T
00-03
E-350 Econoline Van Full Size, All Models Edge All, Except Sport Models
Escape
10 30
7/16", 1/2" 60
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
10, 18mm, 11/16” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
NO DRILL
3.5 5 35
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6
l 33039 Ø
10, 18mm, 11/16”
NO DRILL
3.5 5
35
74664
HG,RW
78013
HG,RW
–
60 74664
HG,RW
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
E-350 Econoline Van Full Size, All Models
3/4”
5
STANDARD WIRE
l 37051 – n 37041 –
1/2”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW T-CONNECTOR
PA, T
WT. CARRYING WT. DISTRIB. INSTALL TIME
3/4”, 7/8”
HITCH NUMBER
20 n 51007 HM, HX, O,
DRILL BITS
INSTALL TIME STYLE
DRILL BITS NO DRILL
WRENCHES
3/4”, 7/8”
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
FOOTNOTES
n 06127 Ø,EF,HM
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
E-350 Econoline Van Full Size, 95-96 Inc. Super Wagon
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
149
FORD
FORD
148
REESE TOWPOWER
REESE TOWPOWER
n 37152 KH n 37042 KH n 88001 – 05-07
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6
20
l 44647 Ø
n 06417 HM
7/8”
1”, 3/8”
20
l 44680 Ø.HM
n 51191 †,HM n 51194 HM
7/8”
1”, 3/8”
7/8”
1”, 3/8”
20 20
1”, 3/8”
10, 18mm, NO DRILL 5/8” 10, 18, NO DRILL 22mm, 5/8”
n 51191 †,HM
7/8”
1”, 3/8”
20
n 51194 HM
7/8”
1”, 3/8”
20
Escort Sedan
1997
n 77018 –
Escort Sedan Escort ZX2 Escort Wagon
98-99 98-03 1997
n 77022 – n 77022 – n 77018 –
Escort Wagon
98-99
n 77078 †,GP,JR
Excursion Excursion w/ Factory 7-way Expedition
00-03 00-05 97-02
OEM REPLACE.
FOOTNOTES
STANDARD WIRE
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
10, 18mm, NO DRILL 5/8” 10, 18, 22mm, NO DRILL 5/8”
3.5 5
25
74703
78104
–
–
3.5 5.25 25
74702
–
BN,CH
–
3.5 5
25
74702
–
BN,CH
–
25
85774
78058
CH
–
3.5 5.25 25
85774
–
CH
–
78070
78058
Factory Tow Package models only
10, 18mm, NO DRILL 5/8” 10, 18, 22mm, NO DRILL 5/8”
3.5 5
BN,CH
3.5 5
25
85774
–
CH
3.5 4
15
35
–
78104
–
–
35
74665
78058
–
–
74665 74665 –
78058 78058 78013
– –
9/16”
30 30 35
–
– – –
1/2”
20
–
78013
–
–
74665 74682 74665
– 78058 78058
– BN
9/16”, 11/16”, 9/16” 13/16” 9/16”, 11/16”, 9/16” 13/16” 3/4”, 11/16”, 13/16” 1/2” 3/4”, 11/16”, 13/16” 1/2”
11/16”
NO DRILL
11/16”
NO DRILL
13/16”, 7/8”, 15/16”
1/2”
15 l 97231 Ø,HM 15
15 n 51024 Ø,HM
2003 11-13
l 51202 Ø,HM, JR,L
Explorer 2 & 4 Dr.
91-94
n 06365 Ø
13/16”, 7/8”, 15/16”
1/2”
10, 18mm, NO DRILL 5/8” 10, 18, NO DRILL 22mm, 5/8” 11/16” NO DRILL
21mm, 3/4”, NO DRILL 7/8”
5
10 15
l 44676 Ø,HM, † l 44681 Ø,HM,TP
11/16”
NO DRILL
11/16”
NO DRILL
n 33052 Ø,GP
3/4”, 7/8”
n 44032 Ø,HM n 44622 Ø,GP
3.4 4 3.5 5
CH
15 15
NO DRILL
5
8
20
7/8”, 3/4”
NO DRILL
7/8”, 3/4”
NO DRILL
5 6
10 20 10 15
–
BN,CH
BN
85219 85219
4
5
45
l 44659 Ø, HM, JR, L 18mm, 3/4” NO DRILL
4
5
45
74665 85759
78058 78058
BN
85219 85219
l 37051 –
18,19mm, NO DRILL 3/4",11/16" 3/4”, 13/16” 1/2”
5
6
25
l 33051 –
5
6
20
74190
–
BN
–
n 37041 –
3/4”, 13/16” 1/2”
5
6
25
n 44100 –
5
6
20
n 51033 –
15, 18, NO DRILL 21mm, 3/4” 15, 18, NO DRILL 21mm, 3/4” 3/4”, 13/16” 1/2”
5
6 15
5
6 15
l 33051 Ø,JF
5
6
20
74724
–
BN,GC
74885
5 5
6 6
n 37012 – l 44067 Ø,JF
5 5
6 6
50 15
5
6 15
5
6
20
15 n 51033 – l 37051 JF n 37041 JF n 51033 –
06996
–
85774
n 06365 –
95-97
–
25
Expedition Explorer, All Styles
Explorer 2 & 4 Dr.
78104
3.5 5
n 06145 Ø,HM n 06147 Ø,HM,TP
9/16”, 11/16”, 13/16” 10mm, 3/4”, 11/16”, 13/16”
–
74703
l 44647 Ø
l 97232 Ø,HM
n 77018 –
35
25
20
l 97207 Ø, †
2013 2013 91-96
3.5 5
3.5 5
l 44680 Ø.HM
Ecsape All, Except S Models Ecsape All, Inc. S Models Escort All Models
NO DRILL
74672
1”, 3/8”
7/8”
10, 18mm, 11/16”
60
n 06417 †,HM
n 06417 HM
WRENCHES
STYLE
l 33039 Ø
FOOTNOTES
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
3.5 5 35
7/16", 1/2" 60
l 97232 Ø,HM 08-12
NO DRILL
15, 18, 21mm, 9/16", 11/16", 3/4", T50 7/8”
l 97207 Ø, †
Escape All, Inc. Hybrid
10, 18mm, 11/16” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
3/4”, 13/16” 1/2” 15, 18, NO DRILL 21mm, 3/4”
25 25
n 44100 Ø
13/16”, 1/2” 7/8”,15/16” 15, 18, 21mm, NO DRILL 3/4”, 15/16”
13/16”, 1/2” 7/8”,15/16” 3/4”, 15/16” 1/2” 13/16”, 1/2” 7/8”,15/16” 15, 18, 21mm, NO DRILL 3/4”, 15/16”
BN
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
Escape All, Inc. Hybrid
WRENCHES
FOOTNOTES
HITCH NUMBER
l 51142 Ø,RT
2004
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Escape
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
151
FORD
FORD
150
REESE TOWPOWER
REESE TOWPOWER
l 37051 JF n 37041 JF n 51033 Ø Explorer 2 Dr. Sport
n 06365 –
2001
13/16”, 7/8”, 15/16”
1/2”
15 n 51033 Ø l 37051 Ø,JF n 37041 Ø,JF n 51033 Ø
n 06365 –
2001
13/16”, 7/8”, 15/16”
1/2”
15 n 51033 Ø l 37051 Ø,JF n 37041 Ø,JF n 51033 Ø
Explorer 2 Dr. Sport
n 06365 –
02-03
13/16”, 7/8”, 15/16”
1/2”
3/4”, 13/16” 1/2” 15, 18, NO DRILL 21mm, 3/4” 15, 18, NO DRILL 21mm, 3/4” 3/4”, 13/16” 1/2” 3/4”, 13/16” 1/2” 15, 18, NO DRILL 21mm, 3/4” 15, 18, NO DRILL 21mm, 3/4” 3/4”, 13/16” 1/2” 3/4”, 13/16” 1/2” 15, 18, NO DRILL 21mm, 3/4”
6 6
n 37012 Ø l 44067 Ø,JF
5
6 15
n 44100 Ø
5
6 15
l 33051 Ø,JF
5 5
6 6
n 37012 Ø l 44067 Ø,JF
5
6 15
30 30
30 30
n 44100 Ø l 33051 Ø,JF
15 n 51033 Ø
NO DRILL
5
6 15
n 37012 Ø
l 37051 Ø,JF
15, 18, 21mm, 3/4” 3/4”, 13/16”
1/2”
5
6
30
l 44067 Ø,JF
n 37041 Ø,JF
3/4”, 13/16”
1/2”
5
6
30
n 44100 Ø
n 51033 Ø
15, 18, 21mm, 3/4”
NO DRILL
5
6 15
Explorer 4 Dr. Explorer 4 Dr.
2001 02-03
l 33031 Ø,KL
Explorer 4 Dr.
04-05
l 33031 Ø,KL
Explorer Models w/1-1/4 Receivers Only 06-10 2001 Explorer Sport Trac
l 51141 Ø,RT,CS
Explorer Sport Trac
02-03
l 51141 Ø,RT,CS
Explorer Sport Trac
04-05
l 51141 Ø,RT,CS
07-10 Explorer Sport Trac F-100, F-150, F-250, F-350 63-72
n 51016 HM n 51017 GP
63-72 F-100, F-150, F-250, F-350 w/Deep Drop Bumper F-100, F-150, F-250, F-350 73-79
l 37069 GU n 51016 HM n 51017 GP
13/16”, 7/8”, 15/16” 13/16”, 7/8”, 15/16” 13/16”, 7/8”, 15/16” 13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8”
13/16”, 7/8”,15/16” 15, 18, 21mm, 3/4”, 15/16” 13/16”, 7/8”,15/16” 3/4”, 15/16” 13/16”, 7/8”,15/16” 15, 18, 21mm, 3/4”, 15/16” 13/16”, 7/8”,15/16” 3/4”, 15/16”
15, 18mm, 7/8” 15, 18mm, 7/8” 13mm, 3/4”
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
BN,GC
74885
20
1/2”
5
6
20
74724
–
BN,GC
74885
1/2” 1/2”
5 5
6 6
40 45
NO DRILL
5
6
20
1/2”
5
6
20
74724
–
BN,GC
74885
1/2” 1/2”
5 5
6 6
40 45
NO DRILL
5
6
20
1/2”
5
6
20
74665
78058
BN
85219
1/2”
5
6
40
5
6
45
5
6
20
NO DRILL
5
8
74724 74665
78104 78058
BN,GC
20
BN
85219 85219
NO DRILL
5
8
20
–
78058
–
–
NO DRILL
5 5
8 6
25 15
– –
78013 78058
– BN
– –
5
6
15
–
78058
BN
–
5
6
15
–
78058
BN
–
– –
– 78058
–
30
BN
85219 –
6 15
n 44542 Ø,KL l 33020 Ø,CS
NO DRILL
5
6 15
l 33020 Ø,CS
NO DRILL
5
6 15
l 33020 Ø,CS
3/16”, 9/32”, 1/2”, 17/32” 3/16”, 9/32”, 1/2”, 17/32”
5
10 40
n 33065 FP
3/4”, 7/8”
1/2”
5
8
5
10 40
n 37087 FP
3/4”, 7/8”
1/2”
6
10 45
n 37081 FP,M
13, 18, 19mm, NO DRILL 7/8”
5
10 45
–
78058
BN
–
3/4”
–
78058
BN
–
–
78058
BN
–
9/16”, 3/4”
1/2”
13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8”
3/16”, 9/32”, 1/2”, 17/32” 3/16”, 9/32”, 1/2”, 17/32”
15/16”, 7/8”, NO DRILL 13/16” 15/16”, 7/8”, NO DRILL 13/16” 15/16”, 7/8”, NO DRILL 13/16”
5 5
7.5 35 10 40
n 36025 FP,GU l 37034 GU
15/16", 3/4” 5/8”
7.5 12 30 7 12 35
5
10 40
l 37094 GU
15/16", 3/4” 5/8”
7
12 35
1/2”
6
10 40
1/2”
6
10 40
1/2”
5 5
8 30 10 45
n 37081 FP,M
06996
–
5
18mm, 3/4” HM,HX deep socket n 44109 FP,GP, GU,HX 18mm, 3/4” deep socket 3/4” n 36025 GH
73-79
6
13/16”, 1/2” 7/8”,15/16” 15, 18, 21mm, NO DRILL 3/4”, 15/16”
74724
NO DRILL
n 44108 FP,GU,
F-100, F-150, F-250, F-350 w/Deep Drop Bumper
5
OEM REPLACE.
5 5
NO DRILL
FOOTNOTES
l 33051 Ø,JF
40 45
STANDARD WIRE
6 15
6 6
T-CONNECTOR
5
5 5
WT. DISTRIB. INSTALL TIME
n 44100 Ø
1/2”
WT. CARRYING
6 15
13/16”, 7/8”,15/16” 15, 18, 21mm, 3/4”, 15/16” 13/16”, 7/8”,15/16” 3/4”, 15/16”
DRILL BITS
5
20
WRENCHES
n 37012 Ø l 44067 Ø,JF
30 30
6
FOOTNOTES
6 6
5
13/16”, 1/2” 7/8”,15/16” 3/4”, 15/16” 1/2”
HITCH NUMBER
5 5
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
l 33051 Ø,JF
DRILL BITS
6 15
WRENCHES
5
FOOTNOTES
DRILL BITS
15, 18, NO DRILL 21mm, 3/4” 3/4”, 13/16” 1/2”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
1/2”
13, 18, 19mm, NO DRILL 7/8”
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
Explorer 4 Dr.
WRENCHES
FOOTNOTES
HITCH NUMBER
15 n 51033 Ø
STYLE
1/2”
INSTALL TIME STYLE
DRILL BITS
WRENCHES 13/16”, 7/8”, 15/16”
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW WT. CARRYING WT. DISTRIB. INSTALL TIME
n 06365 Ø
98-00
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Explorer 2 & 4 Dr.
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
153
FORD
FORD
152
REESE TOWPOWER
REESE TOWPOWER
10 40
l 37094 GU
15/16", 3/4” 5/8”
7
5
10 40
n 44026 GU
3/4”, 7/8”
1/2”
5
10 30
1/2”
6
10 40
1/2”
6
10 40
1/2”
5 5
8 30 10 45
n 51017 FT,GP
HITCH NUMBER
n 44108 FP,GU,
F-100, F-150, F-250, F-350 w/Deep Drop Bumper, Inc. SuperCab, Will Not Fit Custom Fascia F-100, F-150, F-250, F-350 Styleside, All Models Inc. SuperCab
n 37081 FP,K,M
80-86
13, 18, 19mm, NO DRILL 7/8”
87-91
15, 18, 21mm, 9/16", 11/16", 3/4", T50
7/16", 1/2" 35 l 37069 GU
n 37096 HX
n 51016 FT,HM n 51017 FT,GP
n 51009 –
F-100, F-150, F-250, F-350 w/Deep Drop Bumper, Inc. SuperCab F-150 Flareside w/Rear Fascia
92-93
F-150 Styleside, All Models Inc. SuperCab
92-93
15, 18, 21mm, 9/16", 11/16", 3/4", T50
15, 18, 21mm, 9/16", 11/16", 3/4", T50
n 37096 HX n 51016 FT,HM n 51017 FT,GP n 51009 – F-150 w/Deep Drop Bumper, Inc. SuperCab
92-93 06996
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
12
14 45
74426
–
BN
–
–
BN
–
n 96904 @, GP,
10
12 30 74181
–
BN
–
12
14 45 –
BN
–
18, 21mm, 3/4”, 9/16” 13/16”, 7/8” 3/4” 1/2”
6.5 120
l 37034 GU
15/16", 3/4” 5/8”
7
12 35
3/16”, 5 9/32”, 1/2”, 17/32” 3/16”, 5 9/32”, 1/2”, 17/32”
10 40
l 37094 GU
15/16", 3/4” 5/8”
7
12 35
10 40
n 44026 GU
3/4”, 7/8”
1/2”
5
10 30
10 30
n 44108 FP,GU,
1/2”
6
10 40
1/2”
6
10 40
1/2”
5 5
8 30 10 45
74181
–
BN
–
74181
78058
BN
–
1/2”
9/16”, 3/4” 1/2” 15,17,18, 19,21, 22mm, 9/16”,3/4” 13, 18, 19mm, 3/4”, 13/16”
–
1/4”, 1/2”, 5 9/16”
5
7/16", 1/2" 35
7/16", 1/2" 35 l 37069 GU
BN
3/4”
18mm, 3/4” HM,HX deep socket n 44109 FP,GP, GU,HX 18mm, 3/4” deep socket 3/4” n 36025 –
1/2”
7.5 12 30
n 37081 FP,K,M
13, 18, 19mm, NO DRILL 7/8”
n 36025 FP
3/4”
1/2”
7.5 12 30
n 36047 –
3/4”, 9/16”
1/2”
5
n 36025 FP,GU
3/4”
7.5 35
l 37034 GU l 37094 GU
6.5 120
92-93 n 88001 GU
–
12 30 74181
7
74181
74181
n 41904 @,HD,KF, † 18, 21mm,
10
12 30 74181
78058
BN
–
n 96904 @, GP,
10
12 30 74181
–
BN
–
78058
BN
–
5
1/4”, 1/2”, 5 9/16”
3/16”, 5 9/32”, 1/2”, 17/32” 13, 18, 19mm, 3/16”, 5 3/4”, 13/16”, 9/32”, 1/2”, 7/8” 17/32” 3/4”, 7/8” 1/2” 5
9/16” 3/4”, 13/16”, 7/8” 18, 21mm, 9/16” 3/4”, 13/16”, 7/8”
7.5 12 30
74181
15/16", 3/4” 5/8”
7 7
12 35 12 35
74181
n 44026 GU
3/4”, 7/8”
1/2”
5
10 30
10 40
n 44108 FP,GU,
18mm, 3/4” deep socket
1/2”
6
10 40
10 40
n 44109 FP,GP, GU,HX 18mm, 3/4” 1/2”
6
10 40
10 30
n 36025 – n 37081 FP,K,M
5 5
8 30 10 45
HM,HX
1/2”
15/16", 3/4” 5/8”
deep socket
3/4”
1/2”
13, 18, 19mm, NO DRILL 7/8”
BN
30
HD, KF
F-150 Styleside/Flareside, All Models Inc. SuperCab
12 30 74426
n 36025 FP,GU
5
87-91 n 88001 GU
10
7.5 35
9/16”, 3/4” 1/2” 15,17,18, 19,21, 22mm, 9/16”,3/4” 13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8” 3/4”, 7/8”
–
10
HD, KF n 45002 #,GU,TF
n 88001 GU
BN
n 41904 @,HD,KF, † 18, 21mm, 3/4”, 9/16” 13/16”, 7/8”
F-100, F-150, F-250, F-350 87-91 Styleside/Flareside, All Models Inc. SuperCab
–
74181
BN
78058
BN
–
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
18mm, 3/4” HM,HX deep socket n 44109 FP,GP, GU,HX 18mm, 3/4” deep socket 3/4” n 36025 –
12 30 74426
OEM REPLACE.
5
10
FOOTNOTES
3/16”, 9/32”, 1/2”, 17/32” 3/16”, 9/32”, 1/2”, 17/32”
18, 21mm, 3/4”, 9/16” 13/16”, 7/8” 3/4” 1/2”
STANDARD WIRE
13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8”
12 35 n 96904 @, GP,
13/16”, 7/8”
T-CONNECTOR
n 51016 FT,HM
HD, KF 12 35 n 45002 #,GU,TF
KF, †
WT. DISTRIB. INSTALL TIME
7
7.5 12 30 n 41904 @, GP, HD, 18, 21mm, 3/4”, 9/16”
WT. CARRYING
15/16", 3/4” 5/8”
DRILL BITS
l 37034 GU
WRENCHES
7.5 35
FOOTNOTES
5
HITCH NUMBER
1/2”
DRILL BITS
9/16”, 3/4”
WRENCHES
l 37069 GU
FOOTNOTES
STYLE
3/4”
DRILL BITS
n 36025 FP,GU
WRENCHES
10 30
FOOTNOTES
5
HITCH NUMBER
1/2”
INSTALL TIME STYLE
3/4”, 7/8”
1/2”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
7/16", 1/2" 35 n 51009 –
DRILL BITS
WRENCHES 15, 18, 21mm, 9/16", 11/16", 3/4", T50
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW WT. CARRYING WT. DISTRIB. INSTALL TIME
n 88001 GU
80-86
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
F-100, F-150, F-250, F-350 All, Inc. SuperCab, Will Not Fit Custom Fascia
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
155
FORD
FORD
154
REESE TOWPOWER
REESE TOWPOWER
94-96
15, 18, 21mm, 9/16", 11/16", 3/4", T50
7/16", 1/2" 35 n 37096 HX
n 51016 FT,HM n 51017 FT,GP n 51009 –
F-150 Flareside (New Body Style)
2004
F-150 Styleside (New Body Style)
F-150 Flareside (New Body Style)
F-150 Styleside (New Body Style)
F-150 Flareside (New Body Style)
BN
–
12 30 74181
78058
BN
–
74181
78058
BN
–
l 51064 Ø,RT,VB l 37069 VB n 37096 VB
2004
2005
2005
06-08
DRILL BITS
WRENCHES
10 40
13, 18, 19mm, 3/16”, 5 3/4”, 13/16” 9/32”, 1/2”, 17/32” 13, 18, 19mm, 3/16”, 5 3/4”, 13/16”, 9/32”, 1/2”, 7/8” 17/32”
10 40 10 40
5
9/16”, 3/4”
1/2”
15,17,18, 19,21, 22mm, 9/16”,3/4” 13, 18, 19mm, 3/4”, 13/16”
1/4”, 1/2”, 5 9/16”
3/16”, 5 9/32”, 1/2”, 17/32” 13, 18, 19mm, 3/16”, 5 3/4”, 13/16”, 9/32”, 1/2”, 7/8” 17/32” 3/4”, 7/8” 1/2” 5
7.5 35 6.5 120
l 37034 GU l 37094 GU
15/16", 3/4” 5/8”
7 7
12 35 12 35 n 41904 @, GP, HD, 18, 21mm,
10
12 30 74181
10 40
n 44026 GU
3/4”, 7/8”
1/2”
5
10 30 n 96904 @, GP,
10
12 30
10 40
n 44108 FP,GU,
18mm, 3/4” deep socket
1/2”
6
10 40
10 30
n 44109 FP,GP, GU,HX 18mm, 3/4” 1/2”
6
10 40
n 36025 – n 37081 FP,K,M
5 5
8 30 10 45
6 6 5
8 30 10 30 10 30
6 6 6 5
8 8 10 10
30 30 30 30
6 6 6 5
8 8 10 10
30 30 30 30
6 6 6 5
8 8 10 10
30 30 30 30
6 6
8 30 10 20 n 41933 Ø,@,CP,HM, 3/4”, 7/8”
HM,HX
l 33077 Ø,HM,VB l 37090 Ø,VB l 44131 Ø,VB
l 51064 Ø,RT l 37069 VB n 37096 VB
5 9/16”, 3/4” 1/2” 5 15,17,18, 1/4”, 1/2”, 5
10 30 7.5 45 6.5 50
l l l l
44655 33077 37090 44131
l 51064 Ø,RT,VB l 37069 VB n 37096 VB
5 9/16”, 3/4” 1/2” 5 15,17,18, 1/4”, 1/2”, 5
10 7.5 45 6.5 50
l l l l
44655 33077 37090 44131
l 51064 Ø,RT l 37069 VB n 37096 VB
5 9/16”, 3/4” 1/2” 5 15,17,18, 1/4”, 1/2”, 5
10 30 7.5 45 6.5 50
l l l l
44655 33077 37090 44131
n 51075 Ø,CP
21mm, 3/4”, NO DRILL 7/8” 13/16”, 7/8” NO DRILL
6
10 20
l 44655 HM n 44552 Ø,CP
5
8 20
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
7/16”
1/2”
15,17,18, 19,21, 22mm, 9/16” 9/16”,3/4” 3/4”
7/16”
19,21, 22mm, 9/16” 9/16”,3/4” 3/4”
7/16”
19,21, 22mm, 9/16” 9/16”,3/4” 3/4”
7/16”
19,21, 22mm, 9/16” 9/16”,3/4”
10
3/4”
10 30 7.5 45 6.5 50
3/4” 9/16”, 3/4”
9/16”
n 36025 FP,GU
5 5 1/4”, 1/2”, 5
n 51096 Ø,CP,HM
06996
OEM REPLACE.
78058
1/2”
FOOTNOTES
74181
3/4”, 9/16”
WT. DISTRIB. INSTALL TIME
– –
WT. CARRYING
BN BN
DRILL BITS
78058 78058
WRENCHES
74181 74181
FOOTNOTES
5 8 30 7.5 12 30 5 7 30
HITCH NUMBER
1/2” 1/2”
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
3/4” 3/4”
n 36025 – n 36025 FP n 36047 –
FOOTNOTES
DRILL BITS
–
3/4”, 13/16”, 7/8”
l 37069 GU
94-96
BN
n 41904 @,HD,KF, † 18, 21mm,
n 88001 GU
F-150 w/Deep Drop Bumper, Inc. SuperCab
STANDARD WIRE
APPLICATIONS GUIDE
F-150 Styleside/Flareside, All Models Inc. SuperCab
78058
1/2”
15/16", 3/4” 5/8”
deep socket 3/4”
1/2”
13, 18, 19mm, NO DRILL 7/8” 3/4” 7/16” 3/4”
7/16”
3/4”
7/16”
HM,VB
3/4”
7/16”
Ø,HM
3/4”
7/16”
Ø,VB
3/4”
7/16”
Ø
3/4”
7/16”
HM
3/4”
7/16”
Ø,HM,VB
3/4”
7/16”
Ø,VB
3/4”
7/16”
Ø,VB
3/4”
7/16”
HM,VB
3/4”
7/16”
Ø,HM
3/4”
7/16”
Ø,VB
3/4”
7/16”
Ø
3/4”
7/16”
3/4”
7/16”
21mm, 3/4”, NO DRILL 7/8”
7.5 12 30
KF, †
HD, KF
9/16” 3/4”, 13/16”, 7/8” 18, 21mm, 9/16” 3/4”, 13/16”, 7/8”
† n 96933 Ø,@,CP,HM 3/4”, 7/8”
BN
74181
78058
BN
–
74682
–
–
–
78063
–
–
–
74682
–
–
–
74682
–
–
85219
–
–
85219
NO DRILL
10
12 20 74682
NO DRILL
10
12 20
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
94-96
74181
8
74181
n 51017 FT,GP F-150 Styleside, All Models Inc. SuperCab
30
3/4”
7/16", 1/2" 35
n 51016 FT,HM
94-96
T-CONNECTOR
15, 18, 21mm, 9/16", 11/16", 3/4", T50
5
n 36025 –
10 30 10 40
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
1/2”
5
13, 18, 19mm, 3/16”, 5 3/4”, 13/16” 9/32”, 1/2”, 17/32” 13, 18, 19mm, 3/16”, 5 3/4”, 13/16”, 9/32”, 1/2”, 7/8” 17/32”
94-95 94-96 n 88001 GU
F-150 Lightning Pickup
1/2”
STYLE
F-150 Lightning Pickup F-150 Flareside w/Rear Fascia
3/4”, 7/8”
WT. CARRYING WT. DISTRIB. INSTALL TIME
n 51017 FT,GP
WRENCHES
FOOTNOTES
HITCH NUMBER
n 51009 – n 51016 FT,HM
1993
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
F-150 Lightning Pickup
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
157
FORD
FORD
156
REESE TOWPOWER
REESE TOWPOWER
5
7.5 25
n 37096 Ø
6.5 40
n 51020 Ø
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 3/4”, 7/8” NO DRILL 5
n 51095 Ø,FP,GP
3/4”, 7/8”
6
10 20
NO DRILL
10 15
3/4”, 7/8”
NO DRILL
Ø,CP,GP
3/4”, 7/8”
NO DRILL NO DRILL
12 12 10 12
20 20 20 35
74682 74682 74665 78993 74658
Ø
3/4”
GU
15/16", 3/4” 5/8”
l 37094 Ø
15/16", 3/4” 5/8”
7
12 35
n 44007 Ø
3/4”, 7/8”
5
10 20 n 41920 @,GP,SU, † 3/4”, 13/16”, 1/2”
NO DRILL
n 96920 @,GP,SU l 44673 Ø,FP,HM
3/4”, 7/8”
NO DRILL
6
10 20
3/4”
NO DRILL
7/8” 3/4”, 13/16”, 1/2” 7/8”
OEM REPLACE.
Package models only BN
–
10
13 30 74665
–
BN
–
6 7
10 20 12 25 n 41920 @,GP,SU, † 3/4”, 13/16”, 1/2”
10
74665 13 30 78993
n 37096 Ø
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 3/4”, 7/8” NO DRILL 5
6.5 40
l 37094 Ø
15/16", 3/4” 5/8”
7
12 25 n 96920 @,GP,SU
10
13 30
10 15 10 20
n 44007 Ø l 44673 Ø,FP,HM
3/4”, 7/8”
NO DRILL
3/4”, 7/8”
NO DRILL
5 6
10 20 10 20
3/4”, 13/16”, 1/2” 7/8”
FOOTNOTES
85219 85219 BN 85219 Factory Tow 85219 –
–
BN
15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50
BN
– –
BN
85219
Factory Tow 85219 Package models only
74665 n 36099 Ø
3/4”
NO DRILL
6
10 20
l 37069 Ø
9/16”, 3/4”
5
7.5 25
l 37034 GU l 37094 Ø
15/16", 3/4” 5/8”
7 7
12 25 12 25 n 41920 @,SU, †
n 37096 Ø
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 3/4”, 7/8” NO DRILL 5
6.5 40
n 44007 Ø
3/4”, 7/8”
NO DRILL
5
10 20 n 96920 @,GP,SU
10 15 10 20
l 44673 Ø,FP,HM
3/4”, 7/8”
NO DRILL
6
10 20
3/4”, 7/8”
1/2”
NO DRILL
6
15/16", 3/4” 5/8”
74665
3/4”, 13/16”, 1/2” 7/8” 3/4”, 13/16”, 1/2” 7/8”
10
13 30 74665
10
13 30
15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50
n 36099 Ø
3/4”
NO DRILL
6
10 20
–
BN
85219
BN
74665 74665
–
BN
–
74665
–
BN
85219
BN
l 37069 Ø
9/16”, 3/4” 1/2”
5
7.5 25
l 37034 Ø
15/16", 3/4” 5/8”
7
12 25 n 41920 @,SU, †
n 37096 Ø
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 3/4”, 7/8” NO DRILL 5
6.5 40
l 37094 Ø
15/16", 3/4” 5/8”
7
12 25 n 96920 @,GP,SU
10 15 10 20
n 44007 Ø l 44673 Ø,FP,HM
3/4”, 7/8”
NO DRILL
3/4”, 7/8”
NO DRILL
5 6
10 20 10 20
74665 74665 74051
– –
BN
– –
Ø
3/4”
NO DRILL
–
BN
85219
15/16", 3/4” 5/8”
10 12 12 10
74665
GU
7.5 25 6.5 40
n l l n
10 15
l 44673 Ø,FP,HM
10 20 n 96920 @,GP,SU
3/4”, 7/8”
NO DRILL
6
3/4”, 13/16”, 1/2” 7/8” 3/4”, 13/16”, 1/2” 7/8”
10
13 30
10
13 30
15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50
l 37069 Ø n 37096 Ø
15, 18, 21mm, 9/16", 11/16", 3/4", T50
– – – –
74665 74051
7/8”
85219
–
15/16", 3/4” 5/8”
6
–
13 30 74665
n 36099 Ø l 37034 GU
NO DRILL
–
10
7.5 25
3/4”, 7/8”
STANDARD WIRE
WT. DISTRIB. INSTALL TIME 12 20
Ø,CP,GP
6 6 6 7
n n n l
T-CONNECTOR
WT. CARRYING 10
FOOTNOTES
NO DRILL
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
12 20 74682
5
00-03
06996
10
† n 96933 Ø,@,CP,HM 3/4”, 7/8”
9/16”, 3/4” 1/2”
n 51020 Ø n 51095 Ø,FP,GP
n 88001 –
NO DRILL
6
l 37069 Ø
2004
n 88001 –
44645 44645 36099 37034
10 20 n 41933 Ø,@,CP,HM, 3/4”, 7/8”
21mm, 3/4”, NO DRILL 7/8”
15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50
2004
n 88001 –
HITCH NUMBER
DRILL BITS
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
DRILL BITS
WRENCHES
WRENCHES
NO DRILL
8 20 10 15 10 15
9/16”, 3/4” 1/2”
n 51020 Ø n 51095 Ø,FP,GP
F-150 SuperCrew
3/4”, 7/8”
5 5 5
97-03
n 88001 –
F-150 Light Duty Heritage Styleside (Old Body Style)
NO DRILL
n 44552 Ø,CP
l 37069 Ø
n 51020 Ø n 51095 Ø,FP,GP F-150 Light Duty Heritage Flareside (Old Body Style)
3/4”, 7/8”
10 20
9/16”, 3/4” 1/2”
5
n 51020 Ø
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 3/4”, 7/8” NO DRILL 5
n 51095 Ø,FP,GP
3/4”, 7/8”
7/16", 1/2" 35
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
NO DRILL
6
36099 37034 37094 44007
Ø
15/16", 3/4” 5/8”
Ø
3/4”, 7/8”
NO DRILL
6 7 7 5
3/4”, 7/8”
NO DRILL
6
20 25 25 20 n 41920 @,GP,SU, † 3/4”, 13/16”, 1/2” 7/8”
3/4”, 13/16”, 1/2” 7/8”
74665 10
13 30
10
13 30
BN
10 20 74665
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
n 88001 – F-150 Light Duty Styleside
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
n 51096 Ø,CP,HM n 51097 Ø,CP,HM n 51097 Ø,CP,HM
6
DRILL BITS
09-10 09-10 97-03
21mm, 3/4”, NO DRILL 7/8” 13/16”, 7/8” NO DRILL
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
WRENCHES
F-150 Flareside (New Body Style) F-150 Styleside (New Body Style) F-150 Light Duty Flareside
n 51075 Ø,CP
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
STYLE
06-08
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
WT. CARRYING WT. DISTRIB. INSTALL TIME
F-150 Styleside (New Body Style)
STYLE
YEAR
MODEL
APPLICATIONS GUIDE
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
159
FORD
FORD
158
REESE TOWPOWER
REESE TOWPOWER
10 30
3/4”
7/16”
3/4”
7/16”
3/4”
7/16”
5 6 6
10 30 8 30 8 30
2005
7/16”
6
10 30
5 6 6
10 30 8 30 10 20 n 41933 Ø,@,CP,HM, 3/4”, 7/8”
NO DRILL
n 96933 Ø,@,CP,HM 3/4”, 7/8”
NO DRILL
12 20
3/4”
5
10 30
n 37096 VB
15,17,18, 19,21, 1/4”, 1/2”, 5 22mm, 9/16”,3/4” 9/16”
6.5 50
l 37090 Ø
3/4” 3/4”
7/16”
3/4”
7/16”
7/16”
WRENCHES
HITCH NUMBER
HITCH NUMBER
WRENCHES
l 51064 Ø,RT
F-150 SuperCrew New Body Style, w/5.5 & 6.5 ft. Beds
06-08
n 51075 Ø,CP
21mm, 3/4”, 7/8” NO DRILL
6
10 20
l 44131 Ø l 44655 HM n 44552 Ø,CP
NO DRILL
09-12
n 51096 Ø,CP,HM n 51097 Ø,CP,HM
13/16”, 7/8”
F-150 SuperCrew New Body Style, w/5.5 & 6.5 ft. Beds F-250 All Models Inc. SuperCab
3/4”, 7/8”
NO DRILL
5 5
8 20 10 15
n 44645 Ø,CP,GP
3/4”, 7/8”
NO DRILL
6
1/2”
5 15,17,18, 19,21, 1/4”, 1/2”, 5
7.5 35 6.5 120
n 36025 FP,GU l 37034 GU l 37094 GU
3/4”
l 37069 GU n 37096 HX
15/16", 3/4” 5/8” 15/16", 3/4” 5/8”
7.5 12 30 7 12 35 7 12 35 n 41904 @,GP,HD, † 18, 21mm, 3/4”, 9/16”
10 40
n 44026 GU
3/4”, 7/8”
1/2”
5
10 40
n 44108 FP,GU,
18mm, 3/4” deep socket
1/2”
10 30
92-93
n 51016 FT,HM n 51017 FT,GP n 51009 – n 88001 GU
15, 18, 21mm, 9/16", 11/16", 3/4", T50
9/16”, 3/4”
1/2”
22mm, 9/16”,3/4” 9/16” 13, 18, 19mm, 3/16”, 5 3/4”, 13/16” 9/32”, 1/2”, 17/32” 13, 18, 19mm, 3/16”, 5 3/4”, 13/16”, 9/32”, 1/2”, 7/8” 17/32” 3/4”, 7/8” 1/2” 5
21mm, 3/4”, NO DRILL 7/8”
†
–
85219
10
12 20 74682
–
–
85219
10
12 20 74682
–
–
85219
74181
78058
–
–
6
10 40 n 45002 #,GU,TF
3/4”
12
14 45
n 44109 FP,GP, GU,HX 18mm, 3/4” 1/2”
6
10 40
n 36025 –
5
8
deep socket 3/4”
1/2”
1/2”
BN
–
BN
–
74181
78058
–
–
74181
78058
–
–
30
7/16", 1/2" 35
74181
15/16", 3/4” 5/8”
7.5 12 30 7 12 35 7 12 35 n 41904 @,GP,HD, † 18, 21mm, 3/4”, 9/16”
13, 18, 19mm, NO DRILL 7/8” 3/4” 1/2”
5
l 37069 GU
9/16”, 3/4”
1/2”
5
7.5 35
n 36025 FP,GU l 37034 GU l 37094 GU
n 37096 HX
15,17,18, 19,21, 22mm, 9/16”,3/4” 13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8” 3/4”, 7/8”
1/4”, 1/2”, 9/16”
5
6.5 120
l 37094 GU
15/16", 3/4” 5/8”
7
10 40
n 44026 GU
3/4”, 7/8”
1/2”
10 40
n 44108 FP,GU,
18mm, 3/4” deep socket
10 30
n 51016 FT,HM n 51017 FT,GP n 51009 –
3/16”, 9/32”, 5 1/2”, 17/32” 3/16”, 9/32”, 5 1/2”, 17/32” 1/2”
5
15/16", 3/4” 5/8”
10 45
10
12 30 74181
12 35 n 96904 @,GP,HD
13/16”, 7/8” 18, 21mm, 3/4”, 9/16” 13/16”, 7/8”
10
12 30
5
10 30 n 45002 #,GU,TF
3/4”
12
14 45
1/2”
6
10 40
n 44109 FP,GP, GU,HX 18mm, 3/4” 1/2”
6
10 40
n 36025 –
5
8
HM,HX
deep socket 3/4”
1/2”
1/2”
74181
BN
–
BN
–
74181
78058
–
–
74181
78058
–
–
30
7/16", 1/2" 35
74181
94-96
n 37081 FP,K,M
F-250 Heavy Duty All Models Inc. SuperCab 1997
15/16", 3/4” 5/8”
7.5 12 30 7 12 35 7 12 35 n 41904 @,GP,HD, † 18, 21mm, 3/4”, 9/16”
3/4”, 7/8”
1/2”
5
1/2”
l 37069 GU
9/16”, 3/4”
1/2”
5
7.5 35
n 36025 FP,GU l 37034 GU l 37094 GU
n 37096 HX
15,17,18, 19,21, 22mm, 9/16”,3/4” 13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8” 3/4”, 7/8”
1/4”, 1/2”, 9/16”
5
6.5 120
n 44026 GU
10 40
n 44108 FP,GU,
n 51016 FT,HM n 51017 FT,GP n 51009 –
06996
–
12 30 74181
94-96
15, 18, 21mm, 9/16", 11/16", 3/4", T50
74682
10
F-250 All Models Inc. SuperCab
n 88001 GU
85219
10 30 n 96904 @,GP,HD
n 37081 FP,K,M
F-250 w/Deep Drop Bumper, Inc. SuperCab
–
12 30 74181
92-93
15, 18, 21mm, 9/16", 11/16", 3/4", T50
–
10
F-250 w/Deep Drop Bumper, Inc. SuperCab
n 88001 GU
74682
13/16”, 7/8” 18, 21mm, 3/4”, 9/16” 13/16”, 7/8”
HM,HX
OEM REPLACE.
6
FOOTNOTES
7/16”
STANDARD WIRE
3/4”
30
T-CONNECTOR
l 37090 Ø
WT. DISTRIB. INSTALL TIME
6.5 50
WT. CARRYING
15,17,18, 19,21, 1/4”, 1/2”, 5 22mm, 9/16”,3/4” 9/16”
DRILL BITS
n 37096 VB
FOOTNOTES
8
l 44131 Ø l 44655 HM l 33077 Ø,HM
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE 6
DRILL BITS 7/16”
WRENCHES 3/4”
FOOTNOTES
l 33077 Ø,HM
DRILL BITS
10 30
FOOTNOTES
5
HITCH NUMBER
3/4”
7/16", 1/2" 35
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
3/16”, 9/32”, 5 1/2”, 17/32” 3/16”, 5 9/32”, 1/2”, 17/32” 1/2” 5
10 40 10 30
13, 18, 19mm, NO DRILL 7/8” 3/4” 1/2” 15/16", 3/4” 5/8”
18mm, 3/4” HM,HX deep socket n 44109 FP,GP, GU,HX 18mm, 3/4” deep socket
n 36025 –
3/4”
5
10 45
10
12 30 74181
10 30 n 96904 @,GP,HD
13/16”, 7/8” 18, 21mm, 3/4”, 9/16” 13/16”, 7/8”
10
12 30
6
10 40 n 45002 #,GU,TF
3/4”
12
14 45 74181
1/2”
6
10 40
1/2”
5
8
1/2”
BN
–
BN
–
30 74181
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
l 51064 Ø,RT
7/16”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
STYLE
2004
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
WT. CARRYING WT. DISTRIB. INSTALL TIME
F-150 SuperCrew New Body Style, w/5.5 ft. Bed
YEAR
MODEL
F-150 SuperCrew New Body Style, w/5.5 ft. Bed
APPLICATIONS GUIDE
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
161
FORD
FORD
160
REESE TOWPOWER
REESE TOWPOWER
F-250 Super Duty Pickups Only - Will Not Fit Cab & Chassis
02-04 05-07
APPLICATIONS GUIDE
15/16", 3/4” 5/8”
6 7
10 20 12 35 n 41920 @,GP,SU, † 3/4”, 13/16”, 1/2”
10
74682 13 30 78993
n 37096 Ø
15,17,18, 1/4”, 1/2”, 19,21, 22mm, 9/16” 9/16”,3/4” 3/4”, 7/8” NO DRILL
5
6.5 40
l 37094 Ø
15/16", 3/4” 5/8”
7
12 35 n 96920 @,GP,SU
10
13 30
NO DRILL
7/8”
n 51020 Ø n 51095 Ø,FP,GP
10 15 10 20
n 44007 Ø l 44673 Ø,FP,HM
NO DRILL
NO DRILL
5 6
3/4”, 7/8”
3/4”, 7/8”
3/4”, 7/8”
NO DRILL
5 6
10 20 10 20
l 37069 –
9/16”, 3/4”
1/2”
5
7.5 30
n 33088 Ø
3/4”, 7/8”
NO DRILL
6
8
n 37096 –
5
6.5 40
l 37034 GU
15/16", 3/4” 5/8”
7
n 51068 Ø,HM
15,17,18, 1/4”, 1/2”, 19,21, 22mm, 9/16” 9/16”,3/4” 3/4” –
6
10 20
n 37093 Ø
3/4”
6
n 51095 Ø,FP,GP
3/4”, 7/8”
6
10 20
l 37094 –
15/16", 3/4” 5/8”
7
n 44141 Ø,HM l 44673 Ø,FP,HM
3/4”
NO DRILL
3/4”, 7/8”
NO DRILL
6 6
3/4”, 13/16”, 1/2” 7/8”
– 74051
NO DRILL
NO DRILL
20 n 41922 Ø,@,GP, †
13/16”, 7/8” NO DRILL
10
12 15 74682
12 30 n 96922 Ø,@,GP
13/16”, 7/8” NO DRILL
10
12 15
10 30 n 41931 Ø, @, HM,
3/4”, 7/8”
NO DRILL
12
15 30
3/4”, 7/8”
NO DRILL
12
15 30
3/4”
NO DRILL
21, 24mm
NO DRILL
12 18
14 20 18 50
SH, † 12 30 n 96931 Ø, @, HM, SH 10 20 n 45008 Ø,#,TF 10 20 n 45297 Ø, #, CS, EF, HM, LT, M, TF
– –
OEM REPLACE.
STANDARD WIRE
n 36099 Ø l 37034 GU
FOOTNOTES
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
WT. CARRYING
7.5 25
–
–
–
85219
Factory Tow 85219 Package models only
–
–
–
78058
–
85219
–
–
–
74051
n 51068 Ø,HM
3/4”
l 37069 – n 37096 –
9/16”, 3/4” 1/2”
–
6
10 20
n 33088 Ø
3/4”, 7/8”
5
7.5 30 6.5 40
l 37034 GU n 37093 Ø
3/4”
10 20
l 37094 – n 44141 Ø,HM l 44673 Ø,FP,HM
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 3/4”, 7/8” NO DRILL 6
n 45012 Ø,#,TF 20 n 41922 Ø,@,GP, †
12 10
14 20 74894 12 15
NO DRILL
10 12
12 15 15 30
NO DRILL
12
15 30
3/4”
NO DRILL
21, 24mm
NO DRILL
12 18
14 20 18 50
15/16”
NO DRILL
6
8
7 6
12 30 n 96922 Ø,@,GP 10 30 n 41931 Ø, @, HM,
13/16”, 7/8” NO DRILL 3/4”, 7/8”
15/16", 3/4” 5/8”
7
12 30 n 96931 Ø, @,
3/4”, 7/8”
3/4”
NO DRILL
3/4”, 7/8”
NO DRILL
6 6
NO DRILL
15/16", 3/4” 5/8” NO DRILL
SH, †
HM, SH 10 20 n 45008 Ø,#,TF 10 20 n 45297 Ø, #, CS, EF, HM, LT, M, TF
13/16”, 7/8” NO DRILL
7/16", 1/2" 35
74051 n 45012 Ø,#,TF 20 n 41931 Ø, @, EB,
15/16”
NO DRILL
3/4”, 7/8”
NO DRILL
12 12
14 20 15 30
3/4”, 7/8” HM, SH 3/4” 10 20 n 45008 Ø,#,TF 10 20 n 45297 Ø, #, CS, EF, 21, 24mm HM, LT, M, TF n 41931 Ø, @, EB, HM, 3/4”, 7/8” SH, †
NO DRILL
12
15 30
NO DRILL NO DRILL
12 18
14 20 18 50
NO DRILL
12
15 30
NO DRILL
12
15 30
NO DRILL NO DRILL
12 18
14 20 18 50
NO DRILL
12
15 30
NO DRILL
12
15 30
NO DRILL
12 18
14 20 18 50
n 51068 Ø,EB,HM
3/4”
–
6
10 20
n 33088 Ø,EB
3/4”, 7/8”
NO DRILL
6
8
n 51095 Ø,FP,GP
3/4”, 7/8”
NO DRILL
6
10 20
n 37093 Ø,EB
3/4”
NO DRILL
6
10 30 n 96931 Ø, @, EB,
n 44141 Ø,EB,HM l 44673 Ø,FP,HM
3/4”
NO DRILL
3/4”, 7/8”
NO DRILL
6 6
08-10
HM, SH, †
3/4”, 7/8” HM, SH 3/4” n 45008 Ø,#,TF n 45297 Ø, #, CS, EF, 21, 24mm HM, LT, M, TF n 41931 Ø, @, EB, 3/4”, 7/8” HM, SH, †
11-12
n 96931 Ø, @, EB,
3/4”, 7/8” HM, SH 3/4” n 45008 Ø,#,TF n 45297 Ø, #, CS, EF, 21, 24mm HM, LT, M, TF
06996
78058
5
n 96931 Ø, @, EB,
F-250 Super Duty Pickups Only - Will Not Fit Cab & Chassis
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
DRILL BITS
WRENCHES 3/4”
74181
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
NO DRILL
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
F-250 Super Duty w/Deep Drop Bumper F-250 Super Duty Pickups Only - Will Not Fit Cab & Chassis
10 45
9/16”, 3/4” 1/2”
n 51095 Ø,FP,GP
15, 18, 21mm, 9/16", 11/16", 3/4", T50
5
7/16", 1/2" 35
99-01 02-04
n 88001 –
13, 18, 19mm, NO DRILL 7/8”
7/16", 1/2" 35
99-01
15, 18, 21mm, 9/16", 11/16", 3/4", T50
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
l 37069 Ø
97-99
n 88001 – F-250 Super Duty w/Deep Drop Bumper F-250 Super Duty Pickups Only - Will Not Fit Cab & Chassis
WRENCHES
n 37081 FP,K,M
15, 18, 21mm, 9/16", 11/16", 3/4", T50
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
1997
n 88001 – F-250 Super Duty Pickups Only - Will Not Fit Cab & Chassis
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
F-250 Heavy Duty w/Deep Drop Bumper, Inc. SuperCab F-250 Light Duty Styleside
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
163
FORD
FORD
162
REESE TOWPOWER
REESE TOWPOWER
10 30 10 40
n 51009 – n 51016 FT,HM 15, 18, 21mm, 9/16", 11/16", 3/4", T50
DRILL BITS
HITCH NUMBER
10
12 30 74181
10 30 n 96904 @,GP,HD
13/16”, 7/8” 18, 21mm, 3/4”, 9/16” 13/16”, 7/8”
10
12 30
6
10 40 n 45002 #,GU,TF
3/4”
12
14 45
n 44109 FP,GP, GU,HX 18mm, 3/4” 1/2”
6
10 40
n 36025 –
5
8
HM,HX
deep socket 3/4”
1/2”
1/2”
7/16", 1/2" 35
n 37081 FP,K,M
F-350 All Models Inc. SuperCab
94-96 7.5 35
n 36025 FP,GU l 37034 GU l 37094 GU
15/16", 3/4” 5/8”
7.5 12 30 7 12 35 7 12 35 n 41904 @,GP,HD, † 18, 21mm, 3/4”, 9/16”
1/4”, 1/2”, 5 9/16”
6.5 120
n 44026 GU
3/4”, 7/8”
1/2”
5
3/16”, 5 9/32”, 1/2”, 17/32” 1/2” 5
10 40
n 44108 FP,GU,
18mm, 3/4” deep socket
1/2”
10 30 10 40
l 37069 GU
9/16”, 3/4” 1/2”
n 37096 HX
15,17,18, 19,21, 22mm, 9/16”,3/4” 13, 18, 19mm, 3/4”, 13/16”, 7/8” 3/4”, 7/8”
n 51017 FT,GP n 51009 – n 51016 FT,HM
F-350 w/Deep Drop Bumper, Inc. SuperCab
5
13, 18, 19mm, 3/16”, 5 3/4”, 13/16” 9/32”, 1/2”, 17/32”
13, 18, 19mm, NO DRILL 7/8” 3/4” 1/2” 15/16", 3/4” 5/8”
5
10 45
–
–
6
10 40 n 45002 #,GU,TF
3/4”
12
14 45
n 44109 FP,GP, GU,HX 18mm, 3/4” 1/2”
6
10 40
n 36025 –
5
8
HM,HX
deep socket 3/4”
1/2”
1/2”
BN
30 74181
7.5 35
15/16", 3/4” 5/8”
1/4”, 1/2”, 5 9/16”
6.5 120
n 44026 GU
3/4”, 7/8”
1/2”
5
3/16”, 9/32”, 5 1/2”, 17/32” 1/2” 5
10 40
n 44108 FP,GU,
1/2”
l 37069 GU
9/16”, 3/4” 1/2”
n 37096 HX
15,17,18, 19,21, 22mm, 9/16”,3/4” 13, 18, 19mm, 3/4”, 13/16”, 7/8” 3/4”, 7/8”
n 51017 FT,GP n 51009 – n 51016 FT,HM
5
13, 18, 19mm, 3/16”, 9/32”, 5 3/4”, 13/16” 1/2”, 17/32”
10 30 10 40
13, 18, 19mm, NO DRILL 7/8” 3/4” 1/2” 15/16", 3/4” 5/8”
18mm, 3/4” HM,HX deep socket n 44109 FP,GP, GU,HX 18mm, 3/4” deep socket 3/4” n 36025 –
5
10 45
74181
78058
–
–
74181
78058
–
–
10
12 30 74181
10 30 n 96904 @,GP,HD
13/16”, 7/8” 18, 21mm, 3/4”, 9/16” 13/16”, 7/8”
10
12 30 74181
6
10 40 n 45002 #,GU,TF
3/4”
12
14 45
1/2”
6
10 40
1/2”
5
8
1/2”
BN
30
7/16", 1/2" 35
74181
1997 n 51068 Ø,HM
3/4”
l 37069 – l 37069 – n 37096 – n 51095 Ø,FP,GP
06996
78058
12 30
7.5 12 30 7 12 35 7 12 35 n 41904 @,GP,HD, † 18, 21mm, 3/4”, 9/16”
15, 18, 21mm, 9/16", 11/16", 3/4", T50
74181
10
n 36025 FP,GU l 37034 GU l 37094 GU
n 88001 –
–
10 30 n 96904 @,GP,HD
7/16", 1/2" 35
99-01
–
12 30 74181
F-350 Heavy Duty All Models Inc. SuperCab 1997
F-350 Heavy Duty w/Deep Drop Bumper, Inc. SuperCab F-350 Super Duty Pickups Only - Will Not Fit Cab & Chassis
78058
10
n 37081 FP,K,M
15, 18, 21mm, 9/16", 11/16", 3/4", T50
74181
13/16”, 7/8” 18, 21mm, 3/4”, 9/16” 13/16”, 7/8”
94-96
n 88001 GU
BN
74181
92-93
15, 18, 21mm, 9/16", 11/16", 3/4", T50
–
30
F-350 w/Deep Drop Bumper, Inc. SuperCab
n 88001 GU
–
7/16", 1/2" 35
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
n 37081 FP,K,M
13, 18, 19mm, NO DRILL 7/8”
5
10 45
6
8
20 n 41922 Ø,@,GP, †
13/16”, 7/8” NO DRILL
10
12 15
7 6
12 30 n 96922 Ø,@,GP 10 30 n 41931 Ø, @, HM,
13/16”, 7/8” NO DRILL 3/4”, 7/8”
NO DRILL
10 12
12 15 15 30
–
6
10 20
n 33088 Ø
3/4”, 7/8”
9/16”, 3/4”
1/2”
9/16”, 3/4”
1/2”
5 5
7.5 30 7.5 30
l 37034 GU n 37093 Ø
3/4”
5
6.5 40
l 37094 –
15/16", 3/4” 5/8”
7
12 30 n 96931 Ø, @,
3/4”, 7/8”
NO DRILL
12
15 30
6
10 20
n 44141 Ø,HM l 44673 Ø,FP,HM
3/4”
NO DRILL NO DRILL
6 6
3/4” 10 20 n 45008 Ø,#,TF 10 20 n 45297 Ø, #, CS, EF, HM, 21, 24mm
NO DRILL
3/4”, 7/8”
12 18
14 20 18 50
15,17,18, 1/4”, 1/2”, 19,21, 22mm, 9/16” 9/16”,3/4” 3/4”, 7/8” NO DRILL
NO DRILL
15/16", 3/4” 5/8” NO DRILL
SH, †
HM, SH
LT, M, TF
NO DRILL
–
–
–
74051
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 88001 GU
13, 18, 19mm, 3/16”, 5 3/4”, 13/16” 9/32”, 1/2”, 17/32”
78058
OEM REPLACE.
1/2”
74181
FOOTNOTES
18mm, 3/4” deep socket
STANDARD WIRE
n 44108 FP,GU,
3/16”, 5 9/32”, 1/2”, 17/32” 1/2” 5
T-CONNECTOR
10 40
n 51017 FT,GP
WT. DISTRIB. INSTALL TIME
5
1/2”
WT. CARRYING
1/2”
DRILL BITS
3/4”, 7/8”
WRENCHES
n 44026 GU
FOOTNOTES
6.5 120
15/16", 3/4” 5/8”
7.5 12 30 7 12 35 7 12 35 n 41904 @,GP,HD, † 18, 21mm, 3/4”, 9/16”
3/4”
15/16", 3/4” 5/8”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
HITCH NUMBER
5
DRILL BITS
15,17,18, 19,21, 22mm, 9/16”,3/4” 13, 18, 19mm, 3/4”, 13/16”, 7/8” 3/4”, 7/8”
WRENCHES
STYLE
n 37096 HX
FOOTNOTES
WT. CARRYING WT. DISTRIB. INSTALL TIME 7.5 35
WRENCHES
5
FOOTNOTES
9/16”, 3/4” 1/2”
HITCH NUMBER
l 37069 GU
n 36025 FP,GU l 37034 GU l 37094 GU
92-93
1/4”, 1/2”, 9/16”
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
F-350 All Models Inc. SuperCab
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
165
FORD
FORD
164
REESE TOWPOWER
REESE TOWPOWER
APPLICATIONS GUIDE
F-350 Super Duty Pickups Only - Will Not Fit Cab & Chassis
02-04 05-07
NO DRILL
12
15 30
3/4”
NO DRILL
21, 24mm
NO DRILL
12 18
14 20 – 18 50
13/16”, 7/8” NO DRILL 3/4”, 7/8”
15/16", 3/4” 5/8”
7
12 30 n 96931 Ø, @,
3/4”, 7/8”
3/4”
NO DRILL
3/4”, 7/8”
NO DRILL
6 6
SH, †
HM, SH 10 20 n 45008 Ø,#,TF 10 20 n 45297 Ø, #, CS, EF, HM, LT, M, TF
15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50
74051 n 45012 Ø,#,TF 20 n 41931 Ø, @, EB,
n 51068 Ø,EB,HM
3/4”
–
6
10 20
n 33088 Ø,EB
3/4”, 7/8”
NO DRILL
6
8
n 51095 Ø,FP,GP
3/4”, 7/8”
NO DRILL
6
10 20
n 37093 Ø,EB
3/4”
NO DRILL
6
10 30 n 96931 Ø, @, EB,
n 44141 Ø,EB,HM l 44673 Ø,FP,HM
3/4”
NO DRILL
3/4”, 7/8”
NO DRILL
6 6
08-10
HM, SH, †
HM, SH 10 20 n 45008 Ø,#,TF 10 20 n 45297 Ø, #, CS, EF, HM, LT, M, TF n 41931 Ø, @, EB, HM, SH, † HM, SH n 45008 Ø,#,TF n 45297 Ø, #, CS, EF, HM, LT, M, TF n 41931 Ø, @, EB, HM, SH, †
11-12
15/16”
NO DRILL
3/4”, 7/8”
NO DRILL
12 12
14 20 15 30
3/4”, 7/8”
NO DRILL
12
15 30
3/4”
NO DRILL
21, 24mm
NO DRILL
12 18
14 20 18 50
3/4”, 7/8”
NO DRILL
12
15 30
3/4”, 7/8”
NO DRILL
12
15 30
3/4”
NO DRILL
21, 24mm
NO DRILL
12 18
14 20 18 50
3/4”, 7/8”
NO DRILL
12
15 30
NO DRILL
12
15 30
NO DRILL NO DRILL
12 18
14 20 18 50
1/2”, 9/16”
12
15 40
21, 22mm, 1/2”, 9/16” 13/16”, 7/8” 13/16”, 7/8” 9/16”
12
15 40
9/16”
12 12 15
15 40 15 40 16 35
9/16”
15
16 35 –
–
–
–
1/2”, 9/16” 16
16 40 –
–
–
–
3/4”, 5/8”
12
14 60 –
–
–
–
11/16”
15
16 35
–
–
–
n 96931 Ø, @, EB,
F-350 Super Duty Cab & Chassis w/34 Wide Frames
99-00
3/4”, 7/8” HM, SH 3/4” n 45008 Ø,#,TF n 45297 Ø, #, CS, EF, HM, 21, 24mm LT, M, TF 10 45 n 41927 @,SP, † 21, 22mm, 13/16”, 7/8”
n 37087 FP
15/16”, 3/4” 5/8”
6
n 37088 –
15/16”, 3/4” 5/8”
7.5 12 60 n 96927 @,SP, † n 41938 @,CC, † n 96938 @,CC n 41940 @ n 96940 @ n 96943 @ n 45014 #,TF n 96947 @
F-350 Super Duty Cab & Chassis w/34 Wide 99-00 Frames & w/Deep Drop Bumper 01-04 F-350 Super Duty Cab & Chassis w/34 Wide Frames
n 37081 FP,M
13, 18, 19mm, NO DRILL 7/8”
5
21mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21, 22mm, 13/16”, 7/8” 15/16”, 1-1/8” 21, 24mm, 13/16”, 7/8”
n 41927 @,SP, †
21, 22mm, 1/2”, 9/16” 13/16”, 7/8”
12
15 40
n 96927 @,SP, †
21, 22mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21, 22mm, 13/16”, 7/8” 21, 24mm, 13/16”, 7/8”
1/2”, 9/16”
12
15 40
9/16”
15
16 35
9/16”
15
16 35 –
n 96940 @ n 96943 @ n 96947 @ Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
13/16”, 7/8” 9/16”
10 45
n 41940 @
06996
OEM REPLACE.
12 15 15 30
12 30 n 96922 Ø,@,GP 10 30 n 41931 Ø, @, HM,
NO DRILL
13/16”, 7/8” NO DRILL
FOOTNOTES
10 12
7 6
15/16", 3/4” 5/8”
n 96931 Ø, @, EB,
F-350 Super Duty Pickups Only - Will Not Fit Cab & Chassis
NO DRILL
8
STANDARD WIRE
n 44141 Ø,HM l 44673 Ø,FP,HM
14 20 12 15
NO DRILL
6
NO DRILL
T-CONNECTOR
l 37094 –
WT. DISTRIB. INSTALL TIME
10 20
12 10
15/16”
DRILL BITS
3/4”
n 45012 Ø,#,TF 20 n 41922 Ø,@,GP, †
WRENCHES
l 37034 GU n 37093 Ø
FOOTNOTES
7.5 30 6.5 40
HITCH NUMBER
5
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 3/4”, 7/8” NO DRILL 6
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
3/4”, 7/8”
DRILL BITS
n 33088 Ø
WRENCHES
10 20
FOOTNOTES
6
WT. CARRYING
9/16”, 3/4” 1/2”
STYLE
l 37069 – n 37096 –
–
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
1/2”, 9/16” 16 11/16”
15
16 40 16 35 –
–
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
F-350 Super Duty w/Deep Drop Bumper F-350 Super Duty Pickups Only - Will Not Fit Cab & Chassis
DRILL BITS
3/4”
n 51095 Ø,FP,GP
n 88001 –
WRENCHES
FOOTNOTES
HITCH NUMBER
n 51068 Ø,HM
WT. CARRYING WT. DISTRIB. INSTALL TIME
99-01 02-04
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
F-350 Super Duty w/Deep Drop Bumper F-350 Super Duty Pickups Only - Will Not Fit Cab & Chassis
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
167
FORD
FORD
166
REESE TOWPOWER
REESE TOWPOWER
12
15 40
9/16”
15
16 35
1/2”, 9/16” 16
16 40
n 41940 @, † n 96943 @ n 96947 @ F-350 Super Duty Cab & Chassis w/34 Wide Frames
n 41927 @,SP, †
08-12
n 96927 @,SP, † n 41940 @, †
n 96943 @ n 96947 @ F-450 Super Duty Pickups Only - Will Not Fit Cab & Chassis
08-10
F-450 Super Duty Pickups Only - Will Not Fit Cab & Chassis
11-12
F-450 Super Duty Cab & Chassis w/34 Wide Frames
99-04
n 45297 Ø, #, CS,
n 37088 –
15/16”, 3/4” 5/8”
EF, HM, LT, M, TF n 45297 Ø, #, CS, EF, HM, LT, M, TF 7.5 12 60 n 41927 @,SP, †
n 96927 @,SP, † n 41940 @, † n 96940 @ n 96943 @ n 45014 #,TF n 96947 @ F-450 Super Duty Cab & Chassis w/34 Wide Frames
n 37088 –
05-07
15/16”, 3/4” 5/8”
7.5 12 60 n 41927 @,SP, † n 96927 @,SP, † n 41940 @ n 96940 @ n 96943 @ n 45014 #,TF n 96947 @
F-450 Super Duty Cab & Chassis w/34 Wide Frames
n 37088 –
08-12
15/16”, 3/4” 5/8”
7.5 12 60 n 41927 @,SP, † n 96927 @,SP, † n 41940 @ n 96940 @ n 96943 @ n 45014 #,TF n 96947 @
06996
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
15
16 35 –
1/2”, 9/16”
12
15 40
1/2”, 9/16”
12
15 40
9/16”
15
16 35
9/16”
15
16 35 –
21, 22mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21, 22mm, 13/16”, 7/8” 21, 24mm, 13/16”, 7/8” 21, 24mm
11/16”
15
16 35 –
NO DRILL
18
18 50
21, 24mm
NO DRILL
18
18 50
21, 22mm, 1/2”, 9/16” 13/16”, 7/8”
12
15 40
21, 22mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21, 22mm, 13/16”, 7/8” 15/16”, 1-1/8” 21, 24mm, 13/16”, 7/8” 21, 22mm, 13/16”, 7/8”
1/2”, 9/16”
12
15 40
9/16”
15
16 35
9/16”
15
16 35
21, 22mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21, 22mm, 13/16”, 7/8” 15/16”, 1-1/8” 21, 24mm, 13/16”, 7/8” 21, 22mm, 13/16”, 7/8” 21, 22mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21, 22mm, 13/16”, 7/8” 15/16”, 1-1/8” 21, 24mm, 13/16”, 7/8”
1/2”, 9/16” 16
1/2”, 9/16” 16
16 40 –
12
14 60
11/16”
15
16 35
1/2”, 9/16”
12
15 40
1/2”, 9/16”
12
15 40
9/16”
15
16 35
9/16”
15
16 35 16 40 –
3/4”, 5/8”
12
14 60
11/16”
15
16 35
1/2”, 9/16”
12
15 40
1/2”, 9/16”
12
15 40
9/16”
15
16 35
9/16”
15
16 35
1/2”, 9/16” 16
–
–
–
16 40
3/4”, 5/8”
1/2”, 9/16” 16
–
16 40 –
3/4”, 5/8”
12
14 60
11/16”
15
16 35
–
–
–
–
–
–
–
–
–
–
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 96940 @
11/16”
OEM REPLACE.
1/2”, 9/16”
FOOTNOTES
21, 22mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21, 22mm, 13/16”, 7/8” 21, 24mm, 13/16”, 7/8” 21, 22mm, 13/16”, 7/8”
STANDARD WIRE
n 96927 @,SP, †
T-CONNECTOR
WT. DISTRIB. INSTALL TIME 15 40
DRILL BITS
12
WRENCHES
21, 22mm, 1/2”, 9/16” 13/16”, 7/8”
FOOTNOTES
n 41927 @,SP, †
HITCH NUMBER
WT. CARRYING
05-07
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
F-350 Super Duty Cab & Chassis w/34 Wide Frames
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
169
FORD
FORD
168
REESE TOWPOWER
REESE TOWPOWER
n 41940 @, † n 96940 @ n 96943 @ n 45014 #,TF n 96947 @ F-550 Super Duty Cab & Chassis w/34 Wide Frames
n 37088 –
05-07
15/16”, 3/4” 5/8”
7.5 12 60 n 41927 @,SP, †
n 41940 @, † n 96940 @ n 96943 @ n 45014 #,TF n 96947 @ F-550 Super Duty Cab & Chassis w/34 Wide Frames
n 37088 –
08-12
15/16”, 3/4” 5/8”
7.5 12 60 n 41927 @,SP, † n 96927 @,SP, † n 41940 @, † n 96940 @ n 96943 @ n 45014 #,TF n 96947 @
Fiesta 4 Dr. Sedan Fiesta 5 Dr. Hatchback
11-13 11-13
Five Hundred
05-07
5/8”, 11/16” n 77229 Ø,HM n 77228 Ø,HM,JR,KH 10mm, 3/4”,
NO DRILL NO DRILL
11/16”
15 30 n 06301 Ø,GP,JR n 51179 Ø,GP,JR
10, 13, 15mm, 3/4” 10, 13, 15mm, 3/4”
NO DRILL
30
NO DRILL
30
Focus Sedan, Except w/Street Appearance Pkg.
05-07
Focus Focus Focus Focus Focus Focus
08-11 08-11 12-13 12-13 00-03 03-07
n n n n n n n
Focus Sedan
Coupe Sedan Sedan 5 Dr. Hatchback, Except ST Wagon Built Before 11/1/02 Wagon Built After 11/1/02
01-04
51161 77176 77176 77256 77256 77115 77115
06996
3/4”, 7/8”
1/2” 1/2”
Ø,HM
3/4”, 7/8”
1/2”
Ø,HM
3/4”, 7/8”
1/2”
Ø,HM
3/4”, 7/8”
1/2”
Ø,HM
3/4”, 7/8”
1/2”
Ø,HM,JR,KH
10mm, 11/16”
NO DRILL
Ø,HM,JR,KH
10mm, 11/16”
NO DRILL
Ø,GP,JR,KH
13mm, 11/16”
NO DRILL
Ø,GP,JR,KH
13mm, 11/16”
NO DRILL
Ø,JR
7/8”
NO DRILL
Ø,JR
7/8”
NO DRILL
16 35
21, 22mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21, 22mm, 13/16”, 7/8” 15/16”, 1-1/8” 21, 24mm, 13/16”, 7/8” 21, 22mm, 13/16”, 7/8” 21, 22mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21, 22mm, 13/16”, 7/8” 15/16”, 1-1/8” 21, 24mm, 13/16”, 7/8”
1/2”, 9/16” 16
16 40 –
3/4”, 5/8”
12
14 60
11/16”
15
16 35
1/2”, 9/16”
12
15 40
1/2”, 9/16”
12
15 40
9/16”
15
16 35
9/16”
15
16 35
1/2”, 9/16” 16
16 40 –
OEM REPLACE.
15
FOOTNOTES
9/16”
STANDARD WIRE
16 35
T-CONNECTOR
15
DRILL BITS 9/16”
–
–
–
–
–
–
3/4”, 5/8”
12
14 60
11/16”
15
16 35
1/2”, 9/16”
12
15 40
1/2”, 9/16”
12
15 40
9/16”
15
16 35 –
–
–
–
9/16”
15
16 35 –
–
–
–
1/2”, 9/16” 16
16 40
3/4”, 5/8”
12
14 60
11/16”
15
16 35 –
–
74699 78095
78104 78104
CH
– –
CH
78058
–
–
18, 19mm, 6” NO DRILL ratchet 18, 19mm NO DRILL
4
4
30
78087
78058
–
–
4
4
20
78087
78058
–
–
–
78013
–
–
l 44620 Ø,†,HM,JR
3/4”, 7/8”
15 40
78032
09-13 Ø,HM
12
30
Flex Models w/Single Muffler & Dual Tail Pipes On Drivers Side Only Focus Sedan
Ø,HM
1/2”, 9/16”
3.5 4
l 44636 Ø,HM,JR
77114 51161 77114 51161 77114
21, 22mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21, 22mm, 13/16”, 7/8” 15/16”, 1-1/8” 21, 24mm, 13/16”, 7/8” 21, 22mm, 13/16”, 7/8”
10, 13, 15mm, NO DRILL 3/4”
09-13
n n n n n
15 40
n 44525 Ø,JR
Flex All, Inc. EcoBoost
2000
12
20 20 20 20 20
–
78104
–
–
–
78058
–
–
20 30 30 25 25 20 20
78019 78019 85771 85772 74665 –
78058 78058 78104
– –
– – –
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
– CH
78058 78058
– –
– –
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 96927 @,SP, †
WT. DISTRIB. INSTALL TIME
n 96927 @,SP, †
21, 22mm, 1/2”, 9/16” 13/16”, 7/8”
WRENCHES
FOOTNOTES
HITCH NUMBER
7.5 12 60 n 41927 @,SP, †
WT. CARRYING
15/16”, 3/4” 5/8”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
n 37088 –
99-04
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
F-550 Super Duty Cab & Chassis w/34 Wide Frames
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
171
FORD
FORD
170
REESE TOWPOWER
REESE TOWPOWER
Focus ZX5 5 Dr. Hatchback, Except SVT 02-07 & w/Street Appearance Pkg. Freestar Freestyle
n 77114 HM
3/4”, 7/8”
n 51161 HM n 77114 HM n 51161 HM
3/4”, 7/8”
APPLICATIONS GUIDE
LTD Crown Victoria
83-91 92-97 98-09
OEM REPLACE.
FOOTNOTES
STANDARD WIRE – –
– –
–
–
–
–
74699 74699
78104 78104
– –
– –
–
78058
–
–
n 77002 CA
3/4”
1/2”
3/4” 3/4”
1/2” 1/2”
n 25 n n 25 n n 25 n n 25 n
n 77002 CA
LTD, Custom & Galaxie Sedan LTD, Custom & Galaxie Wagon Mustang All Models Mustang All, Except GT Mustang All Models
79-82 79-82 79-86 87-93 94-98
n n n n n
Mustang All, Except Cobra SVT
99-04
n 77029 RB
Mustang All, Except GT/CS California Special, Shelby GT & GT500 Mustang All, Except GT/CS California Special, Shelby GT & GT500 Mustang All V6 Models Mustang All V8 Models, Including GT/CS California Special, Shelby GT & GT500 Probe All, Except GT Ranger Pickup All, Except GT
05-09
n 77242 GP,JR
1” hole saw 13, 15mm, 11/16” 1/4”, 7/16”, 20 1” hole saw 13mm, 11/16” 3/8” 45
2010
n 77243 GP,JR,X
13mm, 11/16”
11-13 11-13
n 77238 Ø,HM,JR n 77238 Ø,GP,HB,JR
7/8”
NO DRILL
10, 13, 15mm, 3/4” 10, 13, 15mm, 3/4”
NO DRILL
25 30
NO DRILL
30
3/4”
1/2”
88002 06043 88002 06043 88002 06043 88002 06043
n 44129 GP,JR n 44525 Ø,JR
1/2”
30 35 30 n 51103 CA,GP 35 30 n 51103 CA,GP 35 30 n 51103 CA,GP 35 30
–
3/4”
1/2”
CA
13mm, 3/4”
1/2”
–
3/4”
1/2”
CA
13mm, 3/4”
1/2”
–
3/4”
1/2”
CA
13mm, 3/4”
1/2”
–
3/4”
1/2”
CA
13mm, 3/4”
1/2”
n 88002 – 25 n 06043 CA 3/4” 1/2” 25 n 06043 CA 9/16”, 5/8”, 11/16" 3/8” 20 9/16”, 5/8”, 11/16" 3/8” 20 13, 15mm, 11/16” 1/4”, 7/16”, 20 3/4”
13mm, 3/4”
1/2”
3/4”
1/2”
13mm, 3/4”
1/2”
13mm, 3/4”
1/2”
35 30 n 51103 CA,GP 30
3/4”
1/2”
10, 13, 15mm, NO DRILL 3/4”
13, 18, 19mm, NO DRILL 7/8”
3.5 5 3.5 4
5
30 30
10 45
13mm, 3/4” 1/2”
3.5 6 30
n 33047 CA,GP
13mm, 3/4”
1/2”
3.5 6
30
–
78058
–
–
13mm, 3/4” 1/2”
3.5 6 30
n 33047 CA,GP
13mm, 3/4”
1/2”
3.5 6
30
74428
78104
–
–
13mm, 3/4” 1/2”
3.5 6 30
n 33047 CA,GP
13mm, 3/4”
1/2”
3.5 6
30
–
78104
–
–
–
78058
–
–
– – – – 74428
78058 78058 78058 78058 78058
–
–
– – – – –
74428
78058
–
–
–
78058
–
–
13mm, 3/4” 1/2”
13mm, 3/4” 1/2”
3.5 6 30
n 33047 CA,GP
13mm, 3/4”
1/2”
3.5 6
30
– – –
3/8”
45
85706
78104
–
–
13mm, 11/16”
NO DRILL NO DRILL
40 40
85706 85706
78104 78104
CH
13mm, 11/16”
CH
– –
– –
78058 78058
–
– –
74426
78058
–
–
78058
A
–
93-97 83-85
n 51032 EG,V
n 37152 Ø
83-85
n 37042 Ø n 88001 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
18,19mm, 3/4”, 7/8”
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/2”
3.5 5 20
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 40
n 33058 EG,SD,V
18, 19mm, 7/8” 1/2”
4
6
20
n 44101 EG
18,19mm, 3/4”, 7/8”
3.5 5
20
1/2”
7/16", 1/2" 35
B,F
74051 n 51032 EG,V
06996
T-CONNECTOR
– 78058
25 n 06043 CA
86-92
WT. DISTRIB. INSTALL TIME
78022 79032
1/2”
RB
WT. CARRYING
20
n 77002 CA
X
DRILL BITS
1/2”
7mm, 10mm, 11/16”, Phillips Screw Driver 3/4”
X
WRENCHES
–
45 20 20
CA
FOOTNOTES
–
1/2”
CA
HITCH NUMBER
78058
NO DRILL
77002 77002 77060 77060 77029
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
–
12, 13mm, 3/4”
n 77002 CA
DRILL BITS
20 20
11/16”
n 77002 CA
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
1/2” 1/2”
83-91
Ranger Pickup All, Except GT
WRENCHES
FOOTNOTES
3/4”, 7/8” 3/4”, 7/8”
LTD Crown Victoria Wagon Full Size
Ranger Pickup All, Except w/Rear Fascia
HITCH NUMBER
–
n 37081 FP,K,M
83-91
LTD Crown Victoria
INSTALL TIME STYLE
–
89-97
LTD Country Squire Wagon Full Size
LTD Crown Victoria
DRILL BITS
78058
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
18,19mm, 3/4”, 7/8”
1/2”
3.5 5 20
n 33058 EG,SD,V
18, 19mm, 7/8” 1/2”
4
6
20
n 44101 EG
18,19mm, 3/4”, 7/8”
3.5 5
20
1/2”
74179
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
–
n 06989 Ø,JR n 06301 Ø,GP,JR
n 77152 GP,JR,TA n 77239 Ø,GP,JR n 77285 Ø,HM,SV
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
20
04-07 05-07
06-09 10-12 2013
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
1/2”
n 51179 Ø,GP,JR F-Series Super Duty Cab & Chassis w/34 Wide Frames & 161 Wheelbase & w/Deep Drop Bumper Fusion Fusion Fusion
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Focus ZX3 3 Dr. Hatchback, Except SVT 00-07 & w/Street Appearance Pkg.
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
173
FORD
FORD
172
REESE TOWPOWER
REESE TOWPOWER
Ranger Pickup
15, 18, 21mm, 9/16", 11/16", 3/4", T50
6
1/4”, 1/2”, 5 9/16”
6.5 40
n 88001 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
7/16", 1/2" 35 n 37152 Ø
n 51032 V
1998
18,19mm, 3/4”, 7/8”
1/2”
3.5 5 20
n 33058 EG,SD,V
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 18,19mm, 3/4”, 7/8”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 40
1/2”
3.5 5 20
n 33058 SD,V n 44101 –
Ranger Pickup All, Except Flareside or w/ Rear Fascia
n 37152 Ø
98-99
n 37042 Ø n 88001 – Ranger Pickup
15, 18, 21mm, 9/16", 11/16", 3/4", T50
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 40
n 51032 V
–
–
74424
78013
–
–
74424
78013
–
–
OEM REPLACE.
78013
FOOTNOTES
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
74424
1/2”
4
6
20
1/2”
3.5 5
20
3.5 5 20
n 33058 SD,V
–
A
–
–
78104
C
–
35 20
74429
78058
A
–
35 20
74657
78013
B
–
35 20
85243
78013
B
–
18,19mm, 3/4”, 7/8”
1/2”
3.5 5 20
n 33058 SD,V
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 40
18, 19mm, 7/8” 18,19mm, 3/4”, 7/8” 18, 19mm, 7/8” 18,19mm, 3/4”, 7/8”
1/2”
4
6
20
1/2”
3.5 5
20
1/2”
4
6
20
1/2”
3.5 5
20
HG
–
74665
n 37042 Ø
Taurus Sedan, All Models
86-91
n 77017 Ø,JR,KH
10, 13, 15mm, 3/4”
NO DRILL
20 n 06368 Ø,GP,JR,KH
15, 18, 21mm, 7/16", 1/2" 35 9/16", 11/16", 3/4", T50 10, 13, 15mm, 3/4” NO DRILL 20
Taurus Sedan,Except SHO Taurus Sedan, Inc. SHO
86-91 92-95
n 77017 Ø,JR
10, 13, 15mm, 3/4”
NO DRILL
n 88002 – 20 n 06368 Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Taurus Sedan, Except SHO Taurus Sedan, Except SHO
92-95 96-99
n 77017 Ø,JR
10, 13, 15mm, 3/4”
NO DRILL
n 88002 – 20 n 06368 Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Taurus SHO
96-99
n 88002 – n 06368 Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
1/2”
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE 20
A
n 37152 Ø
06996
3.5 5
–
04-11
3/4”
–
74665
n 51032 V
1/2”
–
–
04-11
3/4”
1/2”
7/16", 1/2" 35
1/2”
78013
A
n 37152 Ø
3/4”
74424
–
00-03
n 88001 –
20
74665
1/2”
18,19mm, 3/4”, 7/8”
1/2”
3.5 5 20
n 33058 SD,V n 44101 –
Ranger Pickup All, Except Flareside or w/ Rear Fascia
6
–
n 37042 Ø
Ranger Pickup
4
–
n 51032 V
15, 18, 21mm, 9/16", 11/16", 3/4", T50
18, 19mm, 7/8” 18,19mm, 3/4”, 7/8”
1/2”
78013
00-03
n 88001 –
–
74424
18,19mm, 3/4”, 7/8”
n 44101 – Ranger Pickup All, Except Flareside or w/ Rear Fascia
A
74424
n 44101 – Ranger Pickup
18, 19mm, 7/8” 18,19mm, 3/4”, 7/8”
7/16", 1/2" 35
1999
78058
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 40
18, 19mm, 7/8” 18,19mm, 3/4”, 7/8”
1/2”
4
6
20
1/2”
3.5 5
20 74665
74051
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 37042 Ø
Ranger Pickup
74179
74179 n 51032 EG,V
93-97
93-97
DRILL BITS
7/16", 1/2" 35
n 44101 EG Ranger Pickup All, Except w/Rear Fascia
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
1/4”, 1/2”, 5 9/16”
STANDARD WIRE
n 88001 –
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW T-CONNECTOR
n 37042 Ø
WRENCHES
FOOTNOTES
HITCH NUMBER
n 37152 Ø
86-92
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Ranger Pickup All, Except w/Rear Fascia
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
175
FORD
FORD
174
REESE TOWPOWER
CLASS II
NO DRILL
n 44632 GP,JR
18mm, 3/4”, 1/2” 7/8”
4
30
85711
78104
B
–
–
78104
C
–
–
78058
A
–
–
78013
B
–
–
–
C
–
–
–
A
–
78068
78058
A
–
10-13
n 51179 Ø,GP,JR n 06121 GP,JR
Taurus Wagon
86-91
Taurus Wagon Taurus Wagon
Taurus Wagon
92-95 96-99 00-03
n 77017 Ø,JR,KH n 77017 Ø,JR n 77017 Ø,JR n 77017 Ø,JR
04-06
10, 13, 15mm, 3/4” NO DRILL 10, 13, 15mm, 3/4” NO DRILL 10, 13, 15mm, 3/4” NO DRILL 10, 13, 15mm, 3/4” NO DRILL
20 n n 20 n n 20 n n 20 n n n n n n
06368 88002 06368 88002 06368 88002 06368 06991 51101 06991 51101 06301
Ø,GP,JR,KH
10, 13, 15mm, 3/4” NO DRILL
–
3/4”
1/2”
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
–
3/4”
1/2”
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
–
3/4”
1/2”
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Taurus X
08-09
Thunderbird All, Except SC
89-95
n 51179 Ø,GP,JR n 06004 Ø
Thunderbird
96-97
n 06004 Ø
Transit Connect Windstar
10-12 95-98
n 06967 –
Windstar Built Before 11/2002
99-03
n 06967 –
20 35 20 35 20 40 20 40 40 40 40 30
n 44525 Ø,JR
Windstar Built After 11/2002
n 06967 –
2003
FREIGHTLINER
Sprinter All 41 Wide Frames, Except 118 Wheelbase & Factory Metal Step Platform Sprinter 144 & 170 Wheelbase Models Only, Except w/Factory Step Bumper Sprinter w/Factory Step Bumper Sprinter 144 & 170 Wheelbase Models Only, Except w/Factory Step Bumper Sprinter w/Factory Step Bumper Sprinter 144 & 170 Wheelbase Models Only, Except w/Factory Step Bumper
3.5 4
30
30 40
–
78104
A,F
–
NO DRILL
40
–
78104
A,F
–
85707
78104
B,E
–
7/8”
1/2”
30 n 51027 –
3/4”
7/8”
1/2”
30 n 51027 – n 37152 Ø,AF
3/4”
74226
–
G,MX
–
15, 18, 21mm, 9/16", 11/16", 3/4", T50 7/8”
15, 18, 21mm, 9/16", 11/16", 3/4", T50
1/2”
3.5 4 40
3.5 4 40 15,17,18, 19,21, 1/4”, 1/2”, 5 6 1/2”
22mm,T-50, 9/16” 9/16”,3/4” 15,17,18, 19,21, 1/4”, 1/2”, 5 22mm,T-50, 9/16” 9/16”,3/4”
l n n n n
44634 33012 44097 33012 44097
Ø
18mm
NO DRILL
–
7/8”
1/2”
–
3/4”
1/2”
–
7/8”
1/2”
–
3/4”
1/2”
3.5 3.5 3.5 3.5 3.5
4 5 4 5 4
20 45 45 45 45
6.5 40
7/16", 1/2" 40 1/2”
74226
30 n 51027 – n 37152 Ø,AF n 37042 Ø,AF
n 88001 –
10, 13, 15mm, NO DRILL 3/4”
4
NO DRILL
10, 13, 15mm, 3/4” NO DRILL 13mm, 11/16”, 3/4”, 7/8” 13mm, 11/16”, 3/4”, 7/8”
n 37042 Ø,AF n 88001 –
HITCH NUMBER
WRENCHES
10, 13, 15mm, 3/4” NO DRILL 18mm, 3/4”, 7/8” 1/2”
OEM REPLACE.
30 30
Taurus Sedan, Inc. SHO
FOOTNOTES
–
WT. DISTRIB. INSTALL TIME
A
WT. CARRYING
78058
DRILL BITS
78069
WRENCHES
30
FOOTNOTES
3.5 4
HITCH NUMBER
10, 13, 15mm, NO DRILL 3/4”
10, 13, 15mm, 3/4” NO DRILL
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
n 44525 Ø,JR
Ø,GP,JR
DRILL BITS
–
10, 13, 15mm, 3/4” NO DRILL 10, 13, 15mm, 3/4” NO DRILL
WRENCHES
A
Ø,GP,JR Ø,GP,JR
FOOTNOTES
78058
08-09
04-06
STYLE
–
Taurus Sedan, All Models
Taurus Sedan, All Models
WT. CARRYING WT. DISTRIB. INSTALL TIME
40 40 40 40 30
DRILL BITS
10, 13, 15mm, 3/4” NO DRILL 10, 13, 15mm, 3/4” NO DRILL
WRENCHES
Ø,GP,JR Ø,GP,JR
n n n n n
FOOTNOTES
–
INSTALL TIME STYLE
A
DRILL BITS
78013
FOOTNOTES
85243
HITCH NUMBER
IONSTALL TIME STYLE
20
3.5 4 40 6
3/4”
1/2”
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16” 1/4”, 1/2”, 5 9/16”
n 33012 –
7/8”
1/2”
3.5 5
45
n 44097 –
3/4”
1/2”
3.5 4
45
85290
FW,LS
–
G,MX
–
6.5 40
7/16", 1/2" 40
85290
FW,LS
03-06
n 33089 Ø
18mm, 3/4”
NO DRILL
5
7.5 20
–
78104
B,F
–
2007
n 44576 Ø,HM
18, 19mm
NO DRILL
6
7.5 20
–
78013
B
–
2007 08-09
n 44591 Ø,HM n 44576 Ø,HM
18, 19mm
NO DRILL NO DRILL
5 6
7.5 30 7.5 20
– –
78013 78013
B
18, 19mm
B
– –
08-09 10-12
n 44591 Ø,HM n 44576 Ø,HM
18, 19mm
NO DRILL
7.5 30 7.5 20
78013
B
–
NO DRILL
5 6
–
18, 19mm
06996
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
177
APPLICATIONS GUIDE
10, 13, 15mm, 3/4” NO DRILL
20 n 06368 Ø,GP,JR 06991 51101 06991 51101 06301
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
STANDARD WIRE
10, 13, 15mm, 3/4”
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
n 77017 Ø,JR
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
T-CONNECTOR
00-03
STYLE
YEAR
MODEL
Taurus Sedan, All Models
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
Taurus Wagon
APPLICATIONS GUIDE
REESE TOWPOWER
FORD - FREIGHTLINER
FORD - FREIGHTLINER
176
REESE TOWPOWER
n 77005 –
Tracker 2 & 4 Dr. Tracker 2 & 4 Dr.
89-95 96-97
n 77015 Ø,HM n 77015 Ø,HM
Acadia Acadia w/ Tow Package Caballero
07-12 07-12 78-87
Canyon All Models
04-07
n 51074 Ø,GP
21, 22mm, 11/16”
NO DRILL
6
7.5 25
n 44593 Ø,GP
21, 22mm, 11/16”
NO DRILL
6
Canyon All Models
08-12
n 51074 Ø,CP,GP
21, 22mm, 11/16”
NO DRILL
6
7.5 25
n 44593 Ø,CP,GP
21, 22mm, 11/16”
NO DRILL
Envoy
1998
NO DRILL
4
6 15
l 37051 FP,JT,KK 18mm, 3/4” 1/2” n 37041 FP,JT,KK 18mm, 3/4” 1/2” NO DRILL n 51031 Ø, FP, HM, KK 18mm,
5 5 4
14mm, 18, 19mm NO DRILL
– –
78009 74682 –
78058 85262 78058
A
85262 – –
7.5 25
78001
78013
B
85262
7.5 25
74682 78001
78013 78013
BO
6
B
85262 85262
l 33015 Ø,FP,KK,SD 18mm, 7/8” NO DRILL
4
6
15
74682 –
78013 85217
A
85262 –
6 30 6 30 6 15
n 33021 Ø,FP,KK 18mm, 1-1/8” NO DRILL n 44098 Ø, FP, HM, KK 18mm, 1-1/8” NO DRILL
4 4
6 6
20 20
4
6 15
l 33015 Ø,FP,KK,SD 18mm, 7/8” NO DRILL
4
6
15
–
–
A
–
5 5 4
6 30 6 30 6 15
n 33021 Ø,FP,KK 18mm, 1-1/8” NO DRILL n 44098 Ø, FP, HM, KK 18mm, 1-1/8” NO DRILL
4 4
6 6
20 20
7.5 7.5 7.5 10 7
30 30 30 30 30
74425 74425 74178 78180
78058 78058 78058 78058
A
A
– – – –
7.5 30
–
85217
A
–
–
85217
A
–
–
85217
A
–
n 06955 Ø,FP,GP,KK
9/16”, 11/16”, 7/8”
18mm, 7/8”
3/8”
NO DRILL
18mm, 3/4” NO DRILL
18mm, 7/8”
NO DRILL
5
5 25
n 88001 – n 06955 Ø,GP
15, 18, 21mm, 9/16", 11/16", 3/4", T50 18mm, 7/8”
15 n 51031 Ø, FP, HM, KK 18mm,
1-1/8”
15 n 51031 Ø, FP, HM, KK 18mm,
NO DRILL 1-1/8” 18mm, 3/4” 1/2”
18mm, 7/8”
18mm, 7/8”
5
33042 33042 33042 37074 44096
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 7/8”
1/4”, 1/2”, 5 9/16”
6
HM
7/8”
5 5 1/2” 5 1/2”, 9/16” 6 1/2”, 9/16” 5
1/4”, 1/2”, 5 9/16”
6.5 30
n 44656 HM
7/8”
1/2”, 9/16” 5
1/2”, 9/16” 5
7/8”
1/2”, 9/16” 5
7 30 7 30
5
25
–
3/4”, 7/8”
–
3/4”, 7/8”
–
3/4”, 7/8”
HM
7/8”
1/2”
1/2”
NO DRILL
NO DRILL
NO DRILL
A,N –
BO
A A
74180
15 n 51031 Ø,HM
18mm, 1-1/8” 3/4”
NO DRILL
4
6 15
l 33015 Ø,SD
18mm, 7/8”
1/2”
3/4”
1/2”
5 5 4
6 30 6 30 6 15
n 33021 Ø n 44098 Ø,HM
4
18mm, NO DRILL 1-1/8” NO DRILL 15 n 51031 Ø, FP, HM, KK 18mm, 1-1/8” l 37051 FP,JT,KK 18mm, 3/4” 1/2” n 37041 FP,JT,KK 18mm, 3/4” 1/2” NO DRILL 1-1/8” NO DRILL 15 n 51031 Ø, FP, HM, KK 18mm, 1-1/8” l 37051 FP,JT,KK 18mm, 3/4” 1/2” n 37041 FP,JT,KK 18mm, 3/4” 1/2”
n 51031 Ø, FP, HM, KK 18mm,
1-1/8”
06996
NO DRILL
n n n n n
n 51031 Ø, FP, HM, KK 18mm,
n 06955 Ø,FP,GP,KK
18mm, 3/4”
7/16", 1/2" 30
l 37051 JT n 37041 JT n 51031 Ø,HM
n 06955 Ø,FP,GP,KK
l 44569 Ø,GP,JR
30
73-75 76-84 85-91 92-94
99-01
OEM REPLACE.
B B
n 51012 n 51012 HM
Jimmy Downsize, All Models
FOOTNOTES
78013 78013
n 06955 Ø,FP,GP,KK
1998
STANDARD WIRE
– 74896
n 37042 –
Jimmy Downsize, All Models
T-CONNECTOR
20 20
n 06407 –
95-97
WT. DISTRIB. INSTALL TIME
–
n 37152 –
Jimmy Downsize, All Models
WT. CARRYING
B
1-1/8”
Full Size Full Size Full Size Full Size
DRILL BITS
78013
l 37051 FP,JT,KK n 37041 FP,JT,KK 18mm, 3/4” 1/2” NO DRILL n 51031 Ø, FP, HM, KK 18mm, Jimmy Jimmy Jimmy Jimmy
WRENCHES
–
l 51083 Ø,GP,JR,RT
99-01
FOOTNOTES
30
1-1/8”
Envoy
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
93-97
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
NO DRILL
NO DRILL
4
6
15
18mm, 1-1/8” NO DRILL 18mm, 1-1/8” NO DRILL
4 4
6 6
20 20
6 15
l 33015 Ø,FP,KK,SD 18mm, 7/8” NO DRILL
4
6
15
5 5 4
6 30 6 30 6 15
n 33021 Ø,FP,KK 18mm, 1-1/8” NO DRILL n 44098 Ø, FP, HM, KK 18mm, 1-1/8” NO DRILL
4 4
6 6
20 20
4
6 15
l 33015 Ø,FP,KK,SD 18mm, 7/8” NO DRILL
4
6
15
5 5 4
6 30 6 30 6 15
n 33021 Ø,FP,KK 18mm, 1-1/8” NO DRILL n 44098 Ø, FP, HM, KK 18mm, 1-1/8” NO DRILL
4 4
6 6
20 20
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
179
APPLICATIONS GUIDE
Prizm
10, 17, 18mm, 1” hole saw 11/16” 14mm, 18, 19mm NO DRILL
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL GEO
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
GMC
APPLICATIONS GUIDE
REESE TOWPOWER
GEO - GMC
GEO - GMC
178
REESE TOWPOWER
REESE TOWPOWER
NO DRILL 1-1/8” 18mm, 3/4” 1/2”
l 37051 FP,JT,KK n 37041 FP,JT,KK 18mm, 3/4” 1/2” n 51031 Ø, FP, HM, KK 18mm, 1-1/8” NO DRILL Pickup, C/K Series w/6 ft. Bed Pickup, C/K Series w/6 ft. Bed
Pickup, C/K Series w/6 ft. Bed 2 Dr. Extended Cab, Inc. Sportside Fenders
HM,HX n 44109 CQ,FP,GP, GU,HX n 33065 CQ,DX,FP n 44108 CQ,FP,GU, HM,HX n 44109 CQ,FP,GP, GU,HX
85-87
1/2” 1/2”
18mm, 3/4” deep socket 18mm, 3/4” deep socket 3/4”, 7/8”
1/2”
5 5 6
1/2”
6
10 30
1/2” 1/2”
5 6
8 40 10 30
1/2”
6
10 30
18mm, 3/4” deep socket 18mm, 3/4” deep socket
n 41909 @,EK,
88-00
HM,SS, †
n 96909 @,EK,
HM,SS
Pickup, C/K Series w/6 ft. Bed 2 Dr. Regular & Extended Cabs, Inc. Sportside Fenders
88-00 l 37069 – n 37096 CA,HX n 51022 Ø,GP n 51017 GP,FP n 51016 HM,FP n 51021 Ø,HM,J
88-00 Pickup, C/K Series w/6 ft. Bed Equipped w/Aftermarket Roll Pan Pickup, C/K Series w/6 ft. Bed Regular & 88-00 Extended Cabs, Inc. Sportside Fenders w/10 Deep Drop Bumper 63-72 Pickup, C/K Series w/8 ft. Bed
n 51016 CQ,HM,JT n 51017 CQ,GP,JT
13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8”
A
–
– 74425
78058 78058
A A
– –
74178
78058
A
–
10
13 30 85741
78058
A
–
10
13 30 85741
–
BN
– –
15/16", 3/4” 5/8”
7
12 40
85741
78058
A
85741 74180
–
99-00 Classic only
7.5 40 6.5 90
l 37094 –
15/16", 3/4” 5/8”
7
12 40
NO DRILL
5
10 20
n 44105 Ø,GP
5
10 25
3/16”, 9/32”, 1/2”, 17/32”
5
10 40
n 44108 FP,GU,
13, 18, 19mm, NO DRILL 3/4”, 7/8” 18mm, 3/4” 1/2” deep socket
6
10 30
3/16”, 9/32”, 1/2”, 17/32” NO DRILL
5
10 40
n 44109 FP,GP, GU,HX 18mm, 3/4” 1/2”
6
10 30
5
10 20 n 96522 CO,HK
5
5.5 40
85741
78058
A
–
85741
78058
A
–
78058
A
–
1/4”, 1/2”, 9/16”
3/16”, 9/32”, 1/2”, 17/32” 3/16”, 9/32”, 1/2”, 17/32”
HM,HX
deep socket
n 37080 Ø,FS,J
13, 18, 19mm, NO DRILL 7/8”
6
10 20
5
10 40
n 33065 FP
3/4”, 7/8”
1/2”
5
8
5
10 40
n 37087 FP
3/4”, 7/8”
1/2”
6
30 n 41938 @,GP, †
13/16”, 7/8” 9/16”
12
15 40 –
10 45 n 96938 @,GP
13/16”, 7/8” 9/16”
12
15 40
n 41940 @, †
21mm, 9/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8” 21, 24mm, 11/16” 13/16”, 7/8”
15
16 35
15
16 35
15
16 35
n 96947 @
BN
63-72
n 37081 M
13, 18, 19mm, NO DRILL 7/8”
5
10 30
–
78058
A
–
73-84
3/4”, 7/8”
1/2”
78058
A
–
1/2”
18mm, 3/4” deep socket
8 30 10 45 10 30 n 41938 @,GP
74425
3/4”, 7/8”
13/16”, 7/8” 9/16”
12
15 40 74425
–
BN
–
10 30 n 96938 @,GP
13/16”, 7/8” 9/16”
12
15 40 74425
–
BN
–
n 41940 @, †
21mm, 9/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8” 21, 24mm, 11/16” 13/16”, 7/8”
15
16 35 74425
–
BN
–
15
16 35 74425
–
BN
–
15
16 35 74425 78058
A
–
n 88001 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
7/16", 1/2" 35 n 51017 CQ,GP,JT
n 51016 CQ,HM,JT
13, 18, 19mm, 3/4”, 13/16”, 7/8” 13, 18, 19mm, 3/4”, 13/16”
3/16”, 9/32”, 1/2”, 17/32”
5
10 40
n 33065 FP n 37087 FP n 44108 FP,GU,
1/2”
5 6 6
3/16”, 9/32”, 1/2”, 17/32”
5
10 40
n 44109 FP,GP, GU,HX 18mm, 3/4” 1/2”
6
HM,HX
deep socket
n 96940 @ n 96947 @ Pickup, C/K Series w/8 ft. Bed w/ Deep Drop Bumper
85217
l 37034 GU
n 96940 @
Pickup, C/K Series w/8 ft. Bed w/ Deep Drop Bumper Pickup, C/K Series w/8 ft. Bed
–
5 5
9/16”, 3/4” 1/2” 15,17,18, 19,21, 22mm, 9/16”,3/4” 13, 18, 19mm, 3/4” 13, 18, 19mm, 3/4”, 13/16”, 7/8” 13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 7/8”
13, 18, 19mm, 9/16” 13/16”, 15/16” 13, 18, 19mm, 9/16” 13/16”, 15/16”
OEM REPLACE.
8 30 8 40 10 30
3/4”, 7/8” 3/4”, 7/8”
FOOTNOTES
n 33065 CQ,DX,FP n 33065 CQ,DX,FP n 44108 CQ,FP,GU,
STANDARD WIRE
20 20
T-CONNECTOR
6 6
WT. DISTRIB. INSTALL TIME
4 4
WT. CARRYING
n 33021 Ø,FP,KK 18mm, 1-1/8” NO DRILL n 44098 Ø, FP, HM, KK 18mm, 1-1/8” NO DRILL
DRILL BITS
6 30 6 30 6 15
WRENCHES
5 5 4
FOOTNOTES
15
HITCH NUMBER
6
67-72 73-84
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE 4
DRILL BITS
l 33015 Ø,FP,KK,SD 18mm, 7/8” NO DRILL
WRENCHES
6 15
FOOTNOTES
4
n 37081 M
73-84
06996
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
13, 18, 19mm, NO DRILL 7/8”
5
10 30
74425
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
Pickup, C/K Series w/6 ft. Bed
STYLE
15 n 51031 Ø, FP, HM, KK 18mm,
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
NO DRILL
HITCH NUMBER
18mm, 7/8”
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
n 06955 Ø,FP,GP,KK
HITCH NUMBER
WRENCHES
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
2002
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Jimmy Downsize, All Models
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
181
GMC
GMC
180
REESE TOWPOWER
REESE TOWPOWER
3/16”, 5 9/32”, 1/2”, 17/32”
10 40
n 44109 FP,GP, GU,HX 18mm, 3/4” 1/2”
6
18mm, 3/4” deep socket
deep socket
15 40 74178
–
BN
–
15 16 35 74178 15 16 35 74178 15 16 35 74178
– –
BN BN
– –
78058
A
–
74178
78058
A
–
12
n 41940 @, † n 96940 @ n 96947 @
21mm, 13/16”, 7/8” 9/16” 21mm, 13/16”, 7/8” 9/16”
88-91
n 33065 FP
3/4”, 7/8”
1/2”
5
8
3/4”, 7/8”
1/2”
18mm, 3/4” deep socket
21, 24mm, 13/16”, 7/8” 11/16”
30
3/16”, 5 9/32”, 1/2”, 17/32”
10 40
n 37087 FP n 44108 FP,GU,
1/2”
6 6
10 45 10 35 n 41938 @,GP, †
13/16”, 7/8” 9/16”
12
15 40 74178
–
BN
–
3/16”, 5 9/32”, 1/2”, 17/32”
10 40
n 44109 FP,GP, GU,HX 18mm, 3/4” 1/2”
6
10 35 n 96938 @,GP
13/16”, 7/8” 9/16”
12
15 40 74178
–
BN
–
n 41940 @, † n 96940 @ n 96947 @
21mm, 13/16”, 7/8” 9/16”
– –
BN
21mm, 13/16”, 7/8” 9/16”
BN
– –
78058
A
– –
HM,HX
deep socket
88-91
n 37081 M
13, 18, 19mm, NO DRILL 7/8”
5
10 30
15 16 35 74178 15 16 35 74178 15 16 35 74178 74178
88-00
n 36007 Ø
18mm, 3/4”
5
10 40
85741
78058
A
85741 74180
–
l 37069 Ø n 37096 CA,HX n 51017 GP n 51016 HM n 51021 Ø,HM,J n 88001 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
NO DRILL
l 37034 GU
15/16", 3/4” 5/8”
7
12 30
7.5 40 6.5 90
l 37094 –
15/16", 3/4” 5/8”
7
12 30
3/16”, 5 9/32”, 1/2”, 17/32” 3/16”, 5 9/32”, 1/2”, 17/32” NO DRILL 5
10 40
n 44108 FP,GU,
18mm, 3/4” deep socket
1/2”
6
10 30 n 41901 @,DB,
10 40
n 44109 FP,GP, GU,HX 18mm, 3/4” 1/2”
6
10 30 n 96901 @,DB, GP,SN 18, 19mm,
9/16”
HM,HX
deep socket
GP,SN, †
n 45006 #,TF
3/4”
BN
BN
10
13 30 85741
99-00 Classic only BN
9/16”
10
13 30 85741
BN
1/2”
12
14 45
18, 19mm, 9/16” 13/16”, 7/8” 13/16”, 7/8”
10 20
7/16", 1/2" 35
–
74180
88-00 Pickup, C/K Series w/8 ft. Bed Equipped w/Aftermarket Roll Pan Pickup, C/K Series w/8 ft. Bed Regular 88-00 & Extended Cabs, w/10 Deep Drop Bumper 92-00 Pickup, C/K Series w/8 ft. Bed 4 Dr. Crew Cab
n 96522 CO,HK
l 37069 Ø n 37096 CA,HX n 51022 Ø,GP n 51016 HM n 51017 GP
n 51021 Ø,HM,J
06996
21, 24mm, 13/16”, 7/8” 11/16”
5 1/4”, 1/2”, 5
9/16”, 3/4” 1/2” 15,17,18, 19,21, 22mm, 9/16”,3/4” 13, 18, 19mm, 3/4”, 13/16”, 7/8” 13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 7/8”
OEM REPLACE. –
FOOTNOTES BN
WT. DISTRIB. INSTALL TIME
–
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
15 40 74178
13/16”, 7/8” 9/16”
10 30
n 51016 CQ,HM,JT
–
10 30 n 96938 @,GP
5
13, 18, 19mm, 3/4”, 13/16”, 7/8” 13, 18, 19mm, 3/4”, 13/16”
A
12
13, 18, 19mm, NO DRILL 7/8”
7/16", 1/2" 35 n 51017 CQ,GP,JT
78058
13/16”, 7/8” 9/16”
n 37081 M
15, 18, 21mm, 9/16", 11/16", 3/4", T50
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
1/2”
HM,HX
STANDARD WIRE
13, 18, 19mm, 3/4”, 13/16”, 7/8” 13, 18, 19mm, 3/4”, 13/16”
74178
8 30 10 45 10 30 n 41938 @,GP, †
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
5.5 40
74178
78058
A
–
74178
78058
A
–
85741 74180
–
n 37080 Ø,FS,J
13, 18, 19mm, NO DRILL 7/8”
6
10 20
n 36007 Ø
18mm, 3/4”
5
10 40
NO DRILL
l 37034 GU
15/16", 3/4” 5/8”
7
12 40
5 1/4”, 1/2”, 5
7.5 40 6.5 90
l 37094 –
15/16", 3/4” 5/8”
7
12 30
5
10 20
n 44105 Ø,GP
13, 18, 19mm, NO DRILL 3/4”, 7/8”
5
10 25 n 41901 @,DB,
3/16”, 5 9/32”, 1/2”, 17/32” 3/16”, 5 9/32”, 1/2”, 17/32”
10 40
9/16”, 3/4” 1/2” 15,17,18, 19,21, 22mm, 9/16”,3/4” 13, 18, 19mm, 3/4” 13, 18, 19mm, 3/4”, 13/16” 13, 18, 19mm, 3/4”, 13/16”, 7/8” 13, 18, 19mm, 7/8”
5
9/16”
NO DRILL
NO DRILL
5
10 40
18, 19mm, 9/16” GP,SN, † 13/16”, 7/8” n 96901 @,DB, GP,SN 18, 19mm, 9/16” 13/16”, 7/8”
n 45006 #,TF
3/4”
1/2”
BN
10
13 30 85741
99-00 Classic only BN
10
13 30 85741
BN
12
14 45
–
10 20
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
WRENCHES
FOOTNOTES
HITCH NUMBER
7/16", 1/2" 35 n 51017 CQ,GP,JT
1/2” 1/2”
85-87
n 88001 –
Pickup, C/K Series w/8 ft. Bed 4 Dr. Crew Cab w/Deep Drop Bumper Pickup, C/K Series w/8 ft. Bed 2 Dr. Regular & Extended Cabs
10 40
5 6 6
3/4”, 7/8” 3/4”, 7/8”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW T-CONNECTOR
15, 18, 21mm, 9/16", 11/16", 3/4", T50
n 51016 CQ,HM,JT
Pickup, C/K Series w/8 ft. Bed w/ Deep Drop Bumper Pickup, C/K Series w/8 ft. Bed 4 Dr. Crew Cab
3/16”, 5 9/32”, 1/2”, 17/32”
n 33065 FP n 37087 FP n 44108 FP,GU,
85-87 n 88001 –
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Pickup, C/K Series w/8 ft. Bed
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
183
GMC
GMC
182
REESE TOWPOWER
REESE TOWPOWER
85-00
21mm, 3/4”,7/8”
l 37069 Ø
9/16”, 3/4” 1/2”
n 37096 Ø,JL l 51081 Ø,RT,JL
NO DRILL
5
7.5 15
l 33093 Ø,JL
5
7.5 25
l 37034 Ø l 37094 Ø
15/16", 3/4” 5/8”
6.5 35
n 37016 Ø
21mm, 3/4”
10.5 15
l 44563 Ø,JL
21, 22mm, NO DRILL 3/4” 21mm, 3/4”, NO DRILL 7/8” 21, 22mm, NO DRILL 3/4”
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21, 22mm, NO DRILL 6 3/4”
l 44564 Ø,JL n 44619 Ø,CM n 88001 DB
15, 18, 21mm, 9/16", 11/16", 3/4", T50
l 51072 Ø,RT,JL
21mm, 3/4”,7/8”
l 37069 Ø n 37096 Ø,JL
9/16”, 3/4” 1/2”
NO DRILL
5
7.5 15
l 33093 Ø,JL
13/16”, 7/8” 9/16”
12 15
15 40 – 16 35 –
– –
– –
– –
15
16 35 –
–
–
–
15
16 35 – –
7 7
12 25 12 25 n 41932 Ø,@,
21mm, 7/8” HM,JL, † 7.5 12 20 n 96932 Ø,@, HM,JL 21mm, 7/8”
8
6
7.5 15
NO DRILL
12
14 20 74180
NO DRILL
12
14 20
H
85262
–
Amber bulb
–
5
7.5 25 6.5 35
l 37034 Ø l 37094 Ø
10.5 15
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21, 22mm, NO DRILL 6 3/4”
78058
H
85262
–
78058
H
85262
–
Amber bulb
–
15/16", 3/4” 5/8” 15/16", 3/4” 5/8”
7 7
12 25 12 25 n 41932 Ø,@,
NO DRILL
12
14 20 74180
n 37016 Ø
21mm, 3/4”
7.5 12 20 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL
12
14 20
l 44563 Ø,JL
21, 22mm, NO DRILL 3/4” 21mm, 3/4”, NO DRILL 7/8” 21, 22mm, NO DRILL 3/4”
NO DRILL
15
HM,JL, †
6
10.5 15
6
8
6
7.5 15
21mm, 7/8”
RD
15
85262
l 51072 Ø,RT,JL l 37069 Ø l 51081 Ø,RT,JL
21mm, 3/4”,7/8”
NO DRILL
9/16”, 3/4” 1/2” 21, 22mm, 3/4”
NO DRILL
5
7.5 15
l 33093 Ø,JL
5 6
7.5 25 10.5 15
l 37034 Ø l 37094 Ø n 37016 Ø l 44563 Ø,JL l 44564 Ø,JL n 44619 Ø,CM
7/16", 1/2" 35
Pickup, Sierra 2500 LD 6.6 99-02 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan
21mm, 3/4”, NO DRILL 7/8”
6
8
15/16", 3/4” 5/8”
7 7
12 25 12 25 n 41932 Ø,@,
15/16", 3/4” 5/8” 21mm, 3/4”
NO DRILL
21, 22mm, NO DRILL 3/4” 21mm, 3/4”, NO DRILL 7/8” 21, 22mm, NO DRILL 3/4”
15
21mm, 7/8” HM,JL, † 7.5 12 20 n 96932 Ø,@, HM,JL 21mm, 7/8” 21mm, 3/4” 6 10.5 15 n 45009 Ø,#,TF
6
8
6
7.5 15
78058
H
85262
–
78058
H
85262
–
Amber Bulb
–
NO DRILL
12
14 20 85217
NO DRILL
12 12
14 20 14 20
NO DRILL
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
RD
–
15
85262 –
06996
85209
– 8
7/16", 1/2" 35
Pickup, Sierra 1500 LD 8 99-02 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Sierra 2500 LD 6.6 99-02 ft. Bed, 2 & 4 WD
–
15
6
n 44619 Ø,CM
15, 18, 21mm, 9/16", 11/16", 3/4", T50
15/16", 3/4” 5/8”
21mm, 9/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8” 21, 24mm, 11/16” 13/16”, 7/8”
15
6
OEM REPLACE.
n 96938 @,CC n 41940 @, †
8
10.5 15
FOOTNOTES
–
21mm, 3/4”, NO DRILL 7/8”
l 44564 Ø,JL
n 88001 DB
WT. DISTRIB. INSTALL TIME
A
85262
l 51081 Ø,RT,JL
15, 18, 21mm, 9/16", 11/16", 3/4", T50
WT. CARRYING
–
7/16", 1/2" 35
Pickup, Sierra 1500 LD 6.6 99-02 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Sierra 1500 LD 8 99-02 ft. Bed, 2 & 4 WD
n 88001 DB
DRILL BITS
15 40 –
6
6
–
12
21mm, 3/4”, NO DRILL 7/8”
NO DRILL
A
RD
78058
H
85262
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
l 51072 Ø,RT,JL
78058
13/16”, 7/8” 9/16”
n 96947 @ 99-02
74178 n 41938 @,CC, †
n 96940 @
Pickup, Sierra 1500 LD 6.6 ft. Bed, 2 & 4 WD
WRENCHES
FOOTNOTES
10 20
STANDARD WIRE
6
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
13, 18, 19mm, NO DRILL 7/8”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW T-CONNECTOR
n 37080 Ø,FS,J
92-00
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Pickup, C/K Series w/8 ft. Bed 4 Dr. Crew Cab, w/10 Deep Drop Bumper Pickup, C/K Series, Cab & Chassis w/34 Wide Frames
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
185
GMC
GMC
184
REESE TOWPOWER
REESE TOWPOWER
9/16”, 3/4” 1/2” 21, 22mm, 3/4”
NO DRILL
n 37016 Ø l 44563 Ø,JL l 44564 Ø,JL n 44619 Ø,CM
Pickup, Sierra 2500 LD 8 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Sierra 1500 HD 6.6 ft. Bed, 2 & 4 WD
15/16", 3/4” 5/8”
7 7
12 25 12 25 n 41932 Ø,@, HM,JL, † 21mm, 7/8” NO DRILL
12
14 20 74180
7.5 12 20 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL 21mm, 3/4” NO DRILL 6 10.5 15 n 45009 Ø,#,TF
12 12
14 20 14 20
15/16", 3/4” 5/8” 21mm, 3/4”
NO DRILL
21, 22mm, NO DRILL 3/4” 21mm, 3/4”, NO DRILL 7/8” 21, 22mm, NO DRILL 3/4”
15
6
8
6
7.5 15
–
l 51072 Ø,RT,JL
21mm, 3/4”,7/8”
l 37069 Ø n 37096 Ø,JL
9/16”, 3/4” 1/2”
NO DRILL
5
7.5 15
l 33093 Ø,JL
21mm, 3/4”, NO DRILL 7/8”
6
8
5
7.5 25 6.5 35
l 37034 Ø
15/16", 3/4” 5/8”
7
12 25
10.5 15
l 37094 Ø
15/16", 3/4” 5/8”
7
12 25
21mm, 3/4”
7.5 12 20 6 10.5 15
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21, 22mm, NO DRILL 6 3/4”
l 44564 Ø,JL n 44619 Ø,CM n 88001 DB
NO DRILL
21, 22mm, NO DRILL 3/4” 21mm, 3/4”, NO DRILL 7/8” 21, 22mm, NO DRILL 3/4”
15 n 41932 Ø,@,
JL, LT n 37096 Ø,JL
6
8
6
7.5 15
12
14 20
15
n 44657 HM,SA
21, 22mm, 3/4”, 7/8”
1/2”
6
12 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25 74682
NO DRILL 5 3/4” 15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4”
7.5 20
l 44577 Ø, CS, FS,
21, 22mm, 3/4”
NO DRILL
6
11 20 n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
JL, LT
6.5 40
HM, LT, †
13/16”, 7/8”
HM, LT 13/16”, 7/8” n 45022 Ø, #, CS, FS, 18, 21mm NO DRILL LT, TF
12
15 25
13
17 25
n 96944 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
13
16 25
13/16”, 7/8”
RD
85209
H
–
78058
H
–
85262 5
10 20
n 44657 Ø,HM,SA
21, 22mm, 3/4”, 7/8”
1/2”
6
12 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25 74682
NO DRILL 5 3/4” 15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4”
7.5 20
l 44577 Ø, CS, FS,
21, 22mm, 3/4”
NO DRILL
6
11 20 n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
21, 22mm, 3/4”, 7/8”
NO DRILL
l 51073 Ø, RT, CS, FS, 21, 22mm,
JL, LT n 37096 Ø,JL
JL, LT
6.5 40
HM, LT, †
13/16”, 7/8”
HM, LT 13/16”, 7/8” n 45022 Ø, #, CS, FS, 18, 21mm NO DRILL LT, TF
12
15 25
13
17 25
n 45293 Ø, #, CS, FS, 18, 21mm
18
18 25
13
16 25
NO DRILL LT, TF n 96944 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL HM, LT 13/16”, 7/8” 15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50
RD
78058
85262 n 51050 SA
21, 22mm, 3/4”, 7/8”
NO DRILL
5
10 20
n 44657 Ø,HM,SA
21, 22mm, 3/4”, 7/8”
1/2”
6
12 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25 74682
l 51073 Ø, RT, CS, FS, 21, 22mm,
NO DRILL
5
7.5 20
l 44577 Ø, CS, FS,
21, 22mm, 3/4”
NO DRILL
6
11 20 n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
JL, LT
15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
3/4”
JL, LT
OEM REPLACE. 85262
10 20
NO DRILL
FOOTNOTES
STANDARD WIRE H
n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL
15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50
n 51050 SA
06996
RD
85209
14 20 –
HM, LT
n 88001 DB
–
85262
5
21, 22mm, 3/4”, 7/8”
l 51073 Ø, RT, CS, FS, 21, 22mm,
01-02
Amber bulb
85262
n 51050 SA
n 88001 DB
–
H
–
Pickup, Sierra 2500 HD 8 01-02 ft. Bed, 2 & 4 WD
85262
78058
12
21mm, 7/8”
01-02
n 88001 DB
H
– NO DRILL
HM,JL, †
15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50
01-02
78058
15
99-02 01-02
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
8
85262
n 37016 Ø l 44563 Ø,JL
Pickup, Sierra 3500 Series 8 ft. Bed, 2 & 4 WD
WT. CARRYING
DRILL BITS
6
15, 18, 21mm, 9/16", 7/16", 1/2" 35 11/16", 3/4", T50
l 51081 Ø,RT,JL
Pickup, Sierra 1500 HD 6.6 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Sierra 2500 HD 6.6 ft. Bed, 2 & 4 WD
21mm, 3/4”, NO DRILL 7/8”
HM, LT, †
HM, LT n 45022 Ø, #, CS, FS, LT, TF n 45293 Ø, #, CS, FS, LT, TF n 96944 Ø, @, CS, FS, HM, LT
13/16”, 7/8”
13/16”, 7/8” 18, 21mm NO DRILL
12
15 25
13
17 25
18, 21mm
NO DRILL
18
18 25
18, 21, 22mm, NO DRILL 13/16”, 7/8”
13
16 25 85262
H
85219
RD
78058
H
85219
RD
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 88001 DB
WRENCHES
l 37034 Ø l 37094 Ø
FOOTNOTES
7.5 25 10.5 15
HITCH NUMBER
5 6
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
l 33093 Ø,JL
DRILL BITS
7.5 15
WRENCHES
5
FOOTNOTES
NO DRILL
STYLE
DRILL BITS
21mm, 3/4”,7/8”
WT. CARRYING WT. DISTRIB. INSTALL TIME
l 37069 Ø l 51081 Ø,RT,JL
WRENCHES
FOOTNOTES
HITCH NUMBER
l 51072 Ø,RT,JL
99-02
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Pickup, Sierra 2500 LD 8 ft. Bed, 2 & 4 WD
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
187
GMC
GMC
186
REESE TOWPOWER
REESE TOWPOWER
DRILL BITS
WT. CARRYING
WT. DISTRIB. INSTALL TIME
T-CONNECTOR
STANDARD WIRE 78058
l 51081 Ø,RT,JL
21, 22mm, 3/4” 21mm, 3/4”,7/8”
NO DRILL
6
10.5 15
l 37034 Ø
15/16", 3/4” 5/8”
7
12 25 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL
12
14 20
NO DRILL
5
7.5 15
l 37094 Ø
15/16", 3/4” 5/8”
7
12 25 n 45009 Ø,#,TF
12
14 20
21mm, 3/4”
7.5 12 20 6 10.5 15
n 37016 Ø l 44563 Ø,JL l 44564 Ø,JL n 44619 Ø,CM
l 51072 Ø,RT,JL
21mm, 3/4”,7/8”
l 37069 Ø l 51081 Ø,RT,JL
9/16”, 3/4” 1/2” 21, 22mm, 3/4”
NO DRILL
NO DRILL
5
7.5 15
l 33093 Ø,JL
5 6
7.5 25 10.5 15
l 37034 Ø l 37094 Ø
l 44564 Ø,JL n 44619 Ø,CM
Pickup, Sierra 2500 LD 8 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Sierra 1500 HD 6.6 ft. Bed, 2 & 4 WD
6
7.5 15
15 n 41932 Ø,@,
l 51072 Ø,RT,JL
21mm, 3/4”,7/8”
l 37069 Ø n 37096 Ø,JL
9/16”, 3/4” 1/2”
NO DRILL
5
7.5 15
l 33093 Ø,JL
7 7
12 25 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL 21mm, 3/4” NO DRILL 12 25 n 45009 Ø,#,TF
12 12
14 20 14 20
21mm, 3/4”
NO DRILL
7.5 12 20 6 10.5 15 6
8
15
6
7.5 15
5
7.5 25 6.5 35
l 37034 Ø l 37094 Ø
10.5 15
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21, 22mm, NO DRILL 6 3/4”
15 n 41932 Ø,@,
85219
78058
RD
85219
NO DRILL
12
14 20 74682
15/16", 3/4” 5/8”
7 7
12 25 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL 12 25
12
14 20
15/16", 3/4” 5/8”
n 37016 Ø
21mm, 3/4”
7.5 12 20
l 44563 Ø,JL
21, 22mm, NO DRILL 3/4” 21mm, 3/4”, NO DRILL 7/8” 21, 22mm, NO DRILL 3/4”
l 51072 Ø,RT,JL
21mm, 3/4”,7/8”
l 37069 Ø n 37096 Ø,JL
9/16”, 3/4” 1/2”
NO DRILL
5
7.5 15
l 33093 Ø,JL
NO DRILL
6
10.5 15
6
8
6
7.5 15
21mm, 7/8”
15
5
7.5 25 6.5 35
l 37034 Ø l 37094 Ø
10.5 15
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21, 22mm, NO DRILL 6 3/4”
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
78058
RD
85219
78058
RD
85219
6
8
NO DRILL
12
14 20 74682
15/16", 3/4” 5/8”
7 7
12 25 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL 12 25
12
14 20
15/16", 3/4” 5/8”
n 37016 Ø
21mm, 3/4”
7.5 12 20
l 44563 Ø,JL
21, 22mm, NO DRILL 3/4” 21mm, 3/4”, NO DRILL 7/8” 21, 22mm, NO DRILL 3/4”
n 44619 Ø,CM 7/16", 1/2" 35
15 n 41932 Ø,@,
NO DRILL
HM,JL, †
6
10.5 15
6
8
6
7.5 15
21mm, 7/8”
RD
74682 21mm, 3/4”, NO DRILL 7/8”
l 44564 Ø,JL
06996
RD
85262
l 51081 Ø,RT,JL
15, 18, 21mm, 9/16", 11/16", 3/4", T50
78058
8
HM,JL, †
RD
74682 6
03-05
n 88001 DB
85219
15/16", 3/4” 5/8”
7/16", 1/2" 35
03-05
RD
14 20 74682
21mm, 3/4”, NO DRILL 7/8”
n 44619 Ø,CM 15, 18, 21mm, 9/16", 11/16", 3/4", T50
78058
12
85262
l 44564 Ø,JL
n 88001 DB
85219
NO DRILL
21mm, 7/8”
03-04 03-05
RD
8
HM,JL, †
RD
78058
6
21, 22mm, NO DRILL 3/4” 21mm, 3/4”, NO DRILL 7/8” 21, 22mm, NO DRILL 3/4”
85219
74682 21mm, 3/4”, NO DRILL 7/8” 15/16", 3/4” 5/8”
RD
15
7/16", 1/2" 35
l 51081 Ø,RT,JL
Pickup, Sierra 1500 HD 6.6 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Sierra 1500 LD 6.6 ft. Bed, 2 & 4 WD
8
NO DRILL
85262
n 37016 Ø l 44563 Ø,JL
15, 18, 21mm, 9/16", 11/16", 3/4", T50
6
21mm, 3/4”
7/16", 1/2" 35
Pickup, Sierra 2500 LD 6.6 03-04 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Sierra 2500 LD 8 03-04 ft. Bed, 2 & 4 WD
n 88001 DB
HM,JL, †
15
85262
RD
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
15, 18, 21mm, 9/16", 11/16", 3/4", T50
NO DRILL
21, 22mm, NO DRILL 3/4” 21mm, 3/4”, NO DRILL 7/8” 21, 22mm, NO DRILL 3/4”
15 n 41932 Ø,@,
OEM REPLACE.
WRENCHES
14 20 74682
FOOTNOTES
12
HITCH NUMBER
NO DRILL
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
21mm, 7/8”
DRILL BITS
8
WRENCHES
6
FOOTNOTES
21mm, 3/4”, NO DRILL 7/8”
HITCH NUMBER
STYLE
l 33093 Ø,JL
DRILL BITS
7.5 25
WRENCHES
5
FOOTNOTES
9/16”, 3/4” 1/2”
HITCH NUMBER
l 37069 Ø
l 51072 Ø,RT,JL
n 88001 DB
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
WT. CARRYING WT. DISTRIB. INSTALL TIME
03-04
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Pickup, Sierra 2500 LD 6.6 ft. Bed, 2 & 4 WD
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
FOOTNOTES
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
189
GMC
GMC
188
REESE TOWPOWER
REESE TOWPOWER
l 37069 Ø n 37096 Ø,JL
9/16”, 3/4” 1/2”
l 51081 Ø,RT,JL
NO DRILL
21mm, 3/4”, NO DRILL 7/8”
6
8
5
7.5 25 6.5 35
l 37034 Ø
15/16", 3/4” 5/8”
7
12 25
10.5 15
l 37094 Ø
15/16", 3/4” 5/8”
7
12 25
21mm, 3/4”
7.5 12 20 6 10.5 15
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21, 22mm, NO DRILL 6 3/4”
6
8
6
7.5 15
15, 18, 21mm, 9/16", 11/16", 3/4", T50
14 20
85219
15 25 74682
l 51073 Ø, RT, CS, FS, 21, 22mm,
NO DRILL
5
7.5 20
l 44577 Ø, CS, FS,
21, 22mm, 3/4”
NO DRILL
6
11 20 n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25
13
17 25
13
16 25
HM, LT n 45022 Ø, #, CS, FS, LT, TF n 96944 Ø, @, CS, FS, HM, LT
13/16”, 7/8” 18, 21mm NO DRILL
18, 21, 22mm, NO DRILL 13/16”, 7/8”
85262 5
10 20
n 44657 Ø,HM,SA
21, 22mm, 3/4”, 7/8”
1/2”
6
12 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25 74682
NO DRILL 5 3/4” 15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4”
7.5 20
l 44577 Ø, CS, FS,
21, 22mm, 3/4”
NO DRILL
6
11 20 n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
21, 22mm, 3/4”, 7/8”
NO DRILL
JL, LT
HM, LT, †
6.5 40
13/16”, 7/8”
HM, LT 13/16”, 7/8” n 45022 Ø, #, CS, FS, 18, 21mm NO DRILL LT, TF
12
15 25
13
17 25
n 45293 Ø, #, CS, FS, 18, 21mm
18
18 25
13
16 25
RD
78058
85262 21, 22mm, 3/4”, 7/8”
NO DRILL
5
10 20
n 44657 Ø,HM,SA
21, 22mm, 3/4”, 7/8”
1/2”
6
12 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25 74682
l 51073 Ø, RT, CS, FS, 21, 22mm,
NO DRILL
5
7.5 20
l 44577 Ø, CS, FS,
21, 22mm, 3/4”
NO DRILL
6
11 20 n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25
3/4”
JL, LT
HM, LT, †
13/16”, 7/8”
HM, LT 13/16”, 7/8” n 45022 Ø, #, CS, FS, LT, TF 18, 21mm NO DRILL n 45293 Ø, #, CS, FS, LT, TF 18, 21mm NO DRILL HM, LT
13/16”, 7/8”
21mm, 3/4”,7/8”
l 37069 Ø n 37096 Ø,JL
9/16”, 3/4” 1/2”
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
NO DRILL
5
7.5 15
l 33093 Ø,JL
5
7.5 25 6.5 35
l 37034 Ø l 37094 Ø
10.5 15
n l l n
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21, 22mm, 3/4” NO DRILL 6
37016 44563 44564 44619
15 n 41932 Ø,@,
21mm, 3/4”, NO DRILL 7/8”
6
8
NO DRILL
12
14 20 74682
15/16", 3/4” 5/8”
7 7
12 25 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL 12 25
12
14 20
7.5 6 6 6
12 10.5 8 7.5
15/16", 3/4” 5/8”
Ø
21mm, 3/4”
Ø,JL
21, 22mm, 3/4” NO DRILL
NO DRILL
Ø,JL
21mm, 3/4”, 7/8” NO DRILL
Ø,CM
21, 22mm, 3/4”
NO DRILL
HM,JL, †
21mm, 7/8”
85219
RD
78058
85262 l 51072 Ø,RT,JL
RD
RD
85219
13 17 25 18 18 25 13 16 25
7/16", 1/2" 35
l 51081 Ø,RT,JL
06996
RD
12
13/16”, 7/8”
n 96944 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
04-05
78058
12 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
JL, LT
15, 18, 21mm, 9/16", 11/16", 3/4", T50
85219
6
n 51050 SA
n 88001 DB
RD
1/2”
7/16", 1/2" 35
03-06
78058
21, 22mm, 3/4”, 7/8”
HM, LT, †
RD
74682 n 44657 HM,SA JL, LT
OEM REPLACE.
15
10 20
3/4”
FOOTNOTES
WT. DISTRIB. INSTALL TIME
12
NO DRILL LT, TF n 96944 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL HM, LT 13/16”, 7/8”
Pickup, Sierra 1500 LD 5.8 ft. Bed, 2 & 4 WD
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL
5
JL, LT n 37096 Ø,JL
Pickup, Sierra 3500 Series 8 ft. Bed, 2 & 4 WD
85219
NO DRILL
l 51073 Ø, RT, CS, FS, 21, 22mm,
15, 18, 21mm, 9/16", 11/16", 3/4", T50
RD
21, 22mm, 3/4”, 7/8”
n 51050 SA
n 88001 DB
78058
14 20 74682
7/16", 1/2" 35
03-06
85219
85262
n 51050 SA
n 88001 DB
RD
12
21mm, 7/8”
03-05 03-06
78058
NO DRILL
HM,JL, †
7/16", 1/2" 35
JL, LT
Pickup, Sierra 2500 HD 8 ft. Bed, 2 & 4 WD
NO DRILL
21, 22mm, NO DRILL 3/4” 21mm, 3/4”, NO DRILL 7/8” 21, 22mm, NO DRILL 3/4”
15 n 41932 Ø,@,
74682
RD
78058
RD
85219
20 15 15 15
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 44619 Ø,CM
Pickup, Sierra 1500 LD 8 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Sierra 2500 HD 6.6 ft. Bed, 2 & 4 WD
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
l 33093 Ø,JL
l 44564 Ø,JL
15, 18, 21mm, 9/16", 11/16", 3/4", T50
DRILL BITS
7.5 15
n 37016 Ø l 44563 Ø,JL
n 88001 DB
WRENCHES
FOOTNOTES
STYLE
5
STANDARD WIRE
21mm, 3/4”,7/8”
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
l 51072 Ø,RT,JL
WIRING
Up to 2500 lb TW Up to 18000 lb GTW T-CONNECTOR
Pickup, Sierra 1500 LD 6.6 03-05 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Sierra 1500 LD 8 03-05 ft. Bed, 2 & 4 WD
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
191
GMC
GMC
190
REESE TOWPOWER
REESE TOWPOWER
l 37069 Ø n 37096 Ø,JL
9/16”, 3/4” 1/2”
NO DRILL
5
7.5 15
l 33093 Ø,JL
5
7.5 25 6.5 35
l 37034 Ø l 37094 Ø
10.5 15
l 44563 Ø,JL
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21, 22mm, NO DRILL 6 3/4”
15, 18, 21mm, 9/16", 11/16", 3/4", T50
l 51072 Ø,RT,JL
21mm, 3/4”,7/8”
l 37069 Ø n 37096 Ø,JL
9/16”, 3/4” 1/2”
15/16", 3/4” 5/8”
7 7
12 25 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL 12 25
12
14 20
6
10.5 15
6
8
15/16", 3/4” 5/8” 21, 22mm, NO DRILL 3/4” 21mm, 3/4”, NO DRILL 7/8”
NO DRILL
5
7.5 15
l 33093 Ø,JL
5
7.5 25 6.5 35
l 37034 Ø l 37094 Ø
10.5 15
l 44563 Ø,JL l 44564 Ø,JL
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21, 22mm, 3/4” NO DRILL 6
15 n 41932 Ø,@,
l 51072 Ø,RT,JL
21mm, 3/4”,7/8”
l 37069 Ø n 37096 Ø,JL
9/16”, 3/4” 1/2”
NO DRILL
5
7.5 15
l 33093 Ø,JL
5
7.5 25 6.5 35
l 37034 Ø l 37094 Ø
10.5 15
l 44563 Ø,JL l 44564 Ø,JL
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21, 22mm, 3/4” NO DRILL 6
RD
85219
12
14 20 74682
15/16", 3/4” 5/8”
7 7
12 25 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL 12 25
12
14 20
6 6
10.5 15 8 15
21, 22mm, 3/4” NO DRILL
15 n 41932 Ø,@,
78058
RD
85219
78058
RD
85219
21mm, 3/4”, NO DRILL 7/8”
6
8
NO DRILL
12
14 20 74682
15/16", 3/4” 5/8”
7 7
12 25 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL 12 25
12
14 20
6 6
10.5 15 8 15
15/16", 3/4” 5/8” 21, 22mm, 3/4” NO DRILL 21mm, 3/4”, 7/8”
NO DRILL
HM,JL, †
21mm, 7/8”
RD
74682
78058
RD
85219
78058
RD
85219
7.5 15
l 33093 Ø,JL
21mm, 3/4”, 7/8” NO DRILL
6
8
15 n 41932 Ø,@, HM,JL, † 21mm, 7/8” NO DRILL
12
14 20 74682
l 37069 Ø n 37096 Ø,JL
9/16”, 3/4” 1/2”
5
7.5 25 6.5 35
l 37034 Ø l 37094 Ø
15/16", 3/4” 5/8”
7 7
12 25 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL 12 25
12
14 20
15/16", 3/4” 5/8”
10.5 15
l 44563 Ø,JL l 44564 Ø,JL
21mm, 3/4”, 7/8” NO DRILL
6 6
10.5 15 8 15
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21, 22mm, 3/4” NO DRILL 6
21, 22mm, 3/4”
NO DRILL
7/16", 1/2" 35
RD
74682 5
85262 21mm, 3/4”,7/8”
2007
l 37069 Ø
9/16”, 3/4” 1/2”
n 37096 Ø,JL l 51081 Ø,RT,JL
5
7.5 15
l 33093 Ø,JL
21mm, 3/4”, NO DRILL 7/8”
6
8
5
7.5 25
l 37034 Ø
15/16", 3/4” 5/8”
7
12 25 n 41932 Ø,@, HM,JL, † 21mm, 7/8” NO DRILL
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21, 22mm, NO DRILL 6 3/4”
6.5 35
l 37094 Ø
15/16", 3/4” 5/8”
7
12 25 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL
10.5 15
l 44563 Ø,JL
21, 22mm, NO DRILL 3/4” 21mm, 3/4”, NO DRILL 7/8”
6
10.5 15
6
8
NO DRILL
l 44564 Ø,JL
06996
78058
NO DRILL
21mm, 7/8”
21mm, 3/4”,7/8” NO DRILL
l 51072 Ø,RT,JL
15, 18, 21mm, 9/16", 11/16", 3/4", T50
85219
l 51072 Ø,RT,JL
2006
n 88001 DB
RD
85262
l 51081 Ø,RT,JL 15, 18, 21mm, 9/16", 11/16", 3/4", T50
78058
8
HM,JL, †
RD
74682 6
21mm, 3/4”, NO DRILL 7/8”
7/16", 1/2" 35
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
OEM REPLACE.
15
21mm, 3/4”, NO DRILL 7/8” 15/16", 3/4” 5/8”
FOOTNOTES
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
14 20 74682
2006
n 88001 DB
85219
12
21mm, 7/8”
7/16", 1/2" 35
2006
RD
NO DRILL
HM,JL, †
85262
l 51081 Ø,RT,JL 15, 18, 21mm, 9/16", 11/16", 3/4", T50
78058
8
2006
n 88001 DB
85219
6
7/16", 1/2" 35
2006
RD
85262
l 51081 Ø,RT,JL 15, 18, 21mm, 9/16", 11/16", 3/4", T50
78058
21mm, 3/4”, NO DRILL 7/8”
7/16", 1/2" 35
Pickup, Sierra 1500 HD 2006 6.6 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Sierra 1500 LD 5.8 2006 ft. Bed, 2 & 4 WD
n 88001 DB
15 n 41932 Ø,@,
STANDARD WIRE
21mm, 3/4”,7/8”
74682
15
RD
74682
78058
RD
85219
12
14 20 85262
78058
BN,RD
85219
12
14 20
15 85262
RD
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 88001 DB
Pickup, Sierra 1500 LD 8 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Sierra 1500 HD 6.6 ft. Bed, 2 & 4 WD (Classic)
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
l 51072 Ø,RT,JL
T-CONNECTOR
2006
l 44564 Ø,JL
Pickup, Sierra 1500 LD 6.6 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Sierra 1500 LD 8 ft. Bed, 2 & 4 WD
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
04-05
l 51081 Ø,RT,JL
Pickup, Sierra 1500 LD 5.8 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Sierra 1500 LD 6.6 ft. Bed, 2 & 4 WD
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Pickup, Sierra 1500 LD 5.8 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan Pickup, Sierra 1500 HD 6.6 ft. Bed, 2 & 4 WD
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
193
GMC
GMC
192
REESE TOWPOWER
REESE TOWPOWER
9/16”, 3/4” 1/2”
l 51072 Ø,RT,JL
21mm, 3/4”,7/8”
l 37069 Ø n 37096 Ø,JL
9/16”, 3/4” 1/2”
l 37034 Ø l 37094 Ø
10.5 15
l 44563 Ø,JL l 44564 Ø,JL
NO DRILL
5
7.5 15
l 33093 Ø,JL
5
7.5 25 6.5 35
l 37034 Ø l 37094 Ø
10.5 15
l 44563 Ø,JL l 44564 Ø,JL
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21, 22mm, 3/4” NO DRILL 6
l 51072 Ø,RT,JL
21mm, 3/4”,7/8”
l 37069 Ø n 37096 Ø,JL
9/16”, 3/4” 1/2”
NO DRILL
5
7.5 15
l 33093 Ø,JL
5
7.5 25 6.5 35
l 37034 Ø l 37094 Ø
10.5 15
l 44563 Ø,JL l 44564 Ø,JL
15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4” 21, 22mm, 3/4” NO DRILL 6
JL, LT n 37096 Ø,JL
15/16", 3/4” 5/8”
7 7
12 25 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL 12 25
12
14 20
6 6
10.5 15 8 15
15/16", 3/4” 5/8”
21, 22mm, 3/4” NO DRILL 21mm, 3/4”, NO DRILL 7/8”
15 n 41932 Ø,@,
78058
BN,RD
85219
8
NO DRILL
12
14 20 85262
15/16", 3/4” 5/8”
7 7
12 25 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL 12 25
12
14 20
6 6
10.5 15 8 15
15/16", 3/4” 5/8” 21, 22mm, 3/4” NO DRILL 21mm, 3/4”, NO DRILL 7/8”
15 n 41932 Ø,@,
78058
BN,RD
85219
78058
BN,RD
85219
6
8
NO DRILL
12
14 20 85262
15/16", 3/4” 5/8”
7 7
12 25 n 96932 Ø,@, HM,JL 21mm, 7/8” NO DRILL 12 25
12
14 20
6 6
10.5 15 8 15
15/16", 3/4” 5/8” 21, 22mm, 3/4” NO DRILL 21mm, 3/4”, 7/8”
NO DRILL
21mm, 7/8”
RD
85262 21mm, 3/4”, NO DRILL 7/8”
HM,JL, †
78058
BN,RD
85219
78058
BN,RD
85219
21, 22mm, 3/4”, 7/8”
1/2”
6
12 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25 85262
NO DRILL 5 3/4” 15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4”
7.5 20
l 44577 Ø, CS, FS,
21, 22mm, 3/4”
NO DRILL
6
11 20 n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
JL, LT
6.5 40
HM, LT, †
13/16”, 7/8”
HM, LT 13/16”, 7/8” n 45022 Ø, #, CS, FS, 18, 21mm NO DRILL LT, TF
12
15 25
13
17 25
n 96944 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
13
16 25
13/16”, 7/8”
RD
85262 n 44657 HM,SA
NO DRILL
5
10 20
n 44657 Ø,HM,SA
21, 22mm, 3/4”, 7/8”
1/2”
6
12 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25 85262
NO DRILL 5 3/4” 15,17,18, 1/4”, 1/2”, 5 19,21, 22mm, 9/16” 9/16”,3/4”
7.5 20
l 44577 Ø, CS, FS,
21, 22mm, 3/4”
NO DRILL
6
11 20 n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
21, 22mm, 3/4”, 7/8”
NO DRILL
6.5 40
JL, LT
HM, LT, †
13/16”, 7/8”
HM, LT 13/16”, 7/8” n 45022 Ø, #, CS, FS, 18, 21mm NO DRILL LT, TF
12
15 25
13
17 25
n 45293 Ø, #, CS, FS, 18, 21mm
18
18 25
13
16 25
NO DRILL LT, TF n 96944 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL HM, LT 13/16”, 7/8” 7/16", 1/2" 35
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
OEM REPLACE. 85219
6
21mm, 7/8”
FOOTNOTES BN,RD
85262
JL, LT n 37096 Ø,JL
06996
78058
21mm, 3/4”, NO DRILL 7/8”
HM,JL, †
RD
85262
10 20
l 51073 Ø, RT, CS, FS, 21, 22mm,
15, 18, 21mm, 9/16", 11/16", 3/4", T50
WT. DISTRIB. INSTALL TIME
14 20 85262
21mm, 7/8”
7/16", 1/2" 35
n 51050 SA
n 88001 DB
WT. CARRYING
DRILL BITS
12
HM, LT
2007
85219
NO DRILL
HM,JL, †
5
21, 22mm, 3/4”, 7/8”
l 51073 Ø, RT, CS, FS, 21, 22mm,
Pickup, Sierra 2500 HD 8 ft. Bed, 2 & 4 WD (Classic)
BN,RD
8
85262
n 51050 SA
15, 18, 21mm, 9/16", 11/16", 3/4", T50
78058
6
7/16", 1/2" 35
2007 Pickup, Sierra 1500 LD 8 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan (Classic) Pickup, Sierra 2500 HD 2007 6.6 ft. Bed, 2 & 4 WD (Classic)
n 88001 DB
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME 7.5 25 6.5 35
85219
85262
l 51081 Ø,RT,JL 15, 18, 21mm, 9/16", 11/16", 3/4", T50
5
15,17,18, 1/4”, 1/2”, 5 19,21, 9/16” 22mm, 9/16”,3/4” 21, 22mm, 3/4” NO DRILL 6
15 n 41932 Ø,@,
BN,RD
21mm, 3/4”, NO DRILL 7/8”
7/16", 1/2" 35
2007 Pickup, Sierra 1500 LD 6.6 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan (Classic) 2007 Pickup, Sierra 1500 LD 8 ft. Bed, 2 & 4 WD (Classic)
n 88001 DB
l 33093 Ø,JL
78058
85262
l 51081 Ø,RT,JL 15, 18, 21mm, 9/16", 11/16", 3/4", T50
7.5 15
7/16", 1/2" 35
2007 Pickup, Sierra 1500 LD 5.8 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan (Classic) 2007 Pickup, Sierra 1500 LD 6.6 ft. Bed, 2 & 4 WD (Classic)
n 88001 DB
5
STANDARD WIRE
l 37069 Ø n 37096 Ø,JL
NO DRILL
85262
85262
RD
78058
BN,RD
85219
RD
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
15, 18, 21mm, 9/16", 11/16", 3/4", T50
DRILL BITS
21mm, 3/4”,7/8”
l 51081 Ø,RT,JL n 88001 DB
WRENCHES
FOOTNOTES
HITCH NUMBER
l 51072 Ø,RT,JL
WIRING
Up to 2500 lb TW Up to 18000 lb GTW T-CONNECTOR
Pickup, Sierra 1500 HD 2007 6.6 ft. Bed, 2 & 4 WD w/Aftermarket Roll Pan (Classic) Pickup, Sierra 1500 LD 5.8 2007 ft. Bed, 2 & 4 WD (Classic)
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
195
GMC
GMC
194
REESE TOWPOWER
REESE TOWPOWER
WT. DISTRIB. INSTALL TIME
T-CONNECTOR
STANDARD WIRE
15 25 85262
78058
l 51073 Ø, RT, CS, FS, 21, 22mm,
NO DRILL
5
7.5 20
l 44577 Ø, CS, FS,
21, 22mm, 3/4”
NO DRILL
6
11 20 n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
3/4”
HITCH NUMBER
l 51073 Ø, RT, CS, FS, 21, 22mm, JL, LT
3/4”
NO DRILL
NO DRILL
5
5
7.5 20
7.5 20
l 44577 Ø, CS, FS, JL, LT
l 44577 Ø, CS, FS, JL, LT
21, 22mm, 3/4”
21, 22mm, 3/4”
NO DRILL
NO DRILL
6
Pickup, Sierra 3500 HD 8 ft. Bed, 2 & 4 WD (New Body Style)
l 51073 Ø, RT, CS, FS, 21, 22mm, JL, LT
3/4”
l 51073 Ø, RT, CS, FS, 21, 22mm,
07-10
JL, LT
Pickup, Sierra 1500 LD 6.6 ft. Bed, 2 & 4 WD (New Body Style)
Pickup, Sierra 1500 LD 8 ft. Bed, 2 & 4 WD (New Body Style)
Pickup, Sierra 2500 HD 6.6 ft. Bed, 2 & 4 WD (New Body Style)
07-13
07-13
07-13
17 25
18, 21mm
NO DRILL
18
18 25
18, 21, 22mm, NO DRILL 13/16”, 7/8”
13
16 25
6
n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25 85262
13
17 25
18, 21, 22mm, NO DRILL 13/16”, 7/8” 18, 21, 22mm, NO DRILL 13/16”, 7/8”
13
16 25
12
15 25 85262
n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25 85262
n 45022
13/16”, 7/8” 18, 21mm NO DRILL
13
17 25
18, 21mm
NO DRILL
18
18 25
18, 21, 22mm, NO DRILL 13/16”, 7/8” 18, 21, 22mm, NO DRILL 13/16”, 7/8”
13
16 25
12
15 25 85262
n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
12
15 25 85262
13
17 25
18, 21, 22mm, NO DRILL 13/16”, 7/8” 18, 21, 22mm, NO DRILL 13/16”, 7/8”
13
16 25
12
15 25 85262
n 96939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
HM, LT n 45022 Ø, #, CS, FS, LT, TF n 96944 Ø, @, CS, FS, HM, LT 11 20 n 41939 Ø, @, CS, FS, HM, LT, †
3/4”
NO DRILL
NO DRILL
5
5
7.5 20
7.5 20
l 44577 Ø, CS, FS, JL, LT
l 44577 Ø, CS, FS, JL, LT
21, 22mm, 3/4”
21, 22mm, 3/4”
NO DRILL
NO DRILL
6
6
11 20 n 41939
HM, LT Ø, #, CS, FS, LT, TF Ø, #, CS, FS, LT, TF Ø, @, CS, FS, HM, LT Ø, @, CS, FS, HM, LT, †
HM, LT n 45022 Ø, #, CS, FS, LT, TF n 96944 Ø, @, CS, FS, HM, LT 11 20 n 41939 Ø, @, CS, FS, HM, LT, †
13/16”, 7/8”
13/16”, 7/8” 18, 21mm NO DRILL
13/16”, 7/8” 18, 21mm NO DRILL
13/16”, 7/8” 18, 21mm NO DRILL
12
15 25 85262
13
17 25
18, 21mm
NO DRILL
18
18 25
18, 21, 22mm, NO DRILL 13/16”, 7/8”
13
16 25
l 51072 Ø,RT,JL
21mm, 3/4”,7/8”
NO DRILL
5
7.5 15
l 33093 Ø,JL
21mm, 3/4”, 7/8” NO DRILL
6
8
l 51081 Ø,RT,JL
21, 22mm, 3/4”
NO DRILL
6
10.5 15
l 44563 Ø,JL
21, 22mm, 3/4” NO DRILL
6
10.5 15
21mm, 3/4”,7/8”
NO DRILL
5
7.5 15
l 44564 Ø,JL l 33093 Ø,JL
21mm, 3/4”, 7/8” NO DRILL
l 51072 Ø,RT,JL
21mm, 3/4”, 7/8” NO DRILL
6 6
8 8
l 51081 Ø,RT,JL
21, 22mm, 3/4”
NO DRILL
6
10.5 15
l 44563 Ø,JL
21, 22mm, 3/4” NO DRILL
6
10.5 15
21mm, 3/4”,7/8”
NO DRILL
5
7.5 15
l 44564 Ø,JL l 33093 Ø,JL
21mm, 3/4”, 7/8” NO DRILL
l 51072 Ø,RT,JL
21mm, 3/4”, 7/8” NO DRILL
6 6
8 8
l 51081 Ø,RT,JL
21, 22mm, 3/4”
NO DRILL
6
10.5 15
l 44563 Ø,JL
21, 22mm, 3/4” NO DRILL
6
10.5 15
21mm, 3/4”, 7/8” NO DRILL l 44564 Ø,JL n 44563 Ø, CS, FS, GP, 13, 21, 22mm, NO DRILL
6 8
8 15 12 20 n 41942 Ø, @, CS, FS, 13, 21, 22mm, NO DRILL n 96942 Ø, @, CS, FS, 13, 21, 22mm, NO DRILL
11-13
JL, LT
3/4”, 7/8”
15
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
3/4”, 7/8”
3/4”, 7/8” 13, 19, 21, 22mm, 3/8”, 9/16” 3/4”, 7/8” hole saw
RD
78058
BN,RD
85219
BN
78058
BN,RD
85219
BN
78058
BN,RD
85219
BN
78058
BN,RD
85219
BN
78058
BN,RD
85219
85262
78058
BN,RD
85219
85262
78058
BN,RD
85219
15
16 20 85262
78058
BN,RD
85219
15
16 20 85262
–
BN
–
18
18 60
15 15
GP, JL, LT, †
85219
85262
15 15
GP, JL, LT n 45300 #, CS, FS, HM, JL, KH, LT
06996
13
15 25 85262
HM, LT n 45022 Ø, #, CS, FS, LT, TF n 45293 Ø, #, CS, FS, LT, TF n 96944 Ø, @, CS, FS, HM, LT
Pickup, Sierra 1500 LD 5.8 ft. Bed, 2 & 4 WD (New Body Style)
15 25
12
HM, LT, †
n 96944 07-10
12
11 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
n 45293
Pickup, Sierra 3500 HD 6.6 ft. Bed, 2 & 4 WD (New Body Style)
13/16”, 7/8” 18, 21mm NO DRILL
85262
JL, LT
Pickup, Sierra 2500 HD 8 07-10 ft. Bed, 2 & 4 WD (New Body Style)
HM, LT n 45022 Ø, #, CS, FS, LT, TF n 45293 Ø, #, CS, FS, LT, TF n 96944 Ø, @, CS, FS, HM, LT
7/16", 1/2" 35
l 51073 Ø, RT, CS, FS, 21, 22mm,
07-10
JL, LT
BN,RD
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
Pickup, Sierra 2500 HD 6.6 ft. Bed, 2 & 4 WD (New Body Style)
15, 18, 21mm, 9/16", 11/16", 3/4", T50
3/4”
13/16”, 7/8”
OEM REPLACE.
WT. CARRYING 12
HM, LT, †
DRILL BITS
12 20 n 41939 Ø, @, CS, FS, 18, 21, 22mm, NO DRILL
WRENCHES
WRENCHES
6
FOOTNOTES
FOOTNOTES
1/2”
HITCH NUMBER
STYLE
21, 22mm, 3/4”, 7/8”
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
n 44657 Ø,HM,SA
DRILL BITS
DRILL BITS
10 20
HITCH NUMBER
WRENCHES
5
FOOTNOTES
NO DRILL
JL, LT
n 88001 DB
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
21, 22mm, 3/4”, 7/8”
n 51050 SA
2007
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Pickup, Sierra 3500 Series 8 ft. Bed, 2 & 4 WD (Classic)
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
FOOTNOTES
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
197
GMC
GMC
196
REESE TOWPOWER
REESE TOWPOWER
n 44563 Ø, CS, FS, GP, 13, 21, 22mm, NO DRILL
11-13
JL, LT
3/4”, 7/8”
8
85219
n 96942 Ø, @, CS, FS, 13, 21, 22mm, NO DRILL
15
16 20 85262
–
BN
–
18
18 20
8
15
16 20 85262
78058
BN,RD
85219
15
16 20 85262
–
BN
–
18
18 60
15
16 20 85262
78058
BN,RD
85219
15
16 20 85262
–
BN
–
18
18 20
15
16 20 85262
78058
BN,RD
85219
15
16 20 85262
–
BN
–
78058
BN,RD
85219
–
–
–
–
–
–
HITCH NUMBER
GP, JL, LT 3/4”, 7/8” n 45300 Ø, #, CS, FS, 13, 19, 21, 3/8”, 9/16” HM, JL, LT 22mm, 3/4”, hole saw 7/8” 12 20 n 41942 Ø, @, CS, FS, 13, 21, 22mm, NO DRILL GP, JL, LT, † 3/4”, 7/8”
n 96942 Ø, @, CS, FS, 13, 21, 22mm, NO DRILL
Pickup, Sierra 3500 HD 8 ft. Bed, 2 & 4 WD (New Body Style)
n 44563 Ø, CS, FS, GP, 13, 21, 22mm, NO DRILL
11-13
JL, LT
3/4”, 7/8”
8
GP, JL, LT n 45300 #, CS, FS, HM, JL, KH, LT 12 20 n 41942 Ø, @, CS, FS, GP, JL, LT, †
3/4”, 7/8” 13, 19, 21, 22mm, 3/8”, 9/16” 3/4”, 7/8” hole saw 13, 21, 22mm, NO DRILL 3/4”, 7/8”
APPLICATIONS GUIDE
n 96942 Ø, @, CS, FS, 13, 21, 22mm, NO DRILL
Pickup, Sierra Denali HD 6.6 ft. Bed, 2 & 4 WD (New Body Style)
n 44563 Ø, CS, FS, GP, 13, 21, 22mm, NO DRILL
11-12
JL, LT
3/4”, 7/8”
8
GP, JL, LT n 45300 Ø, #, CS, FS, HM, JL, LT 12 20 n 41942 Ø, @, CS, FS, GP, JL, LT
3/4”, 7/8” 13, 19, 21, 22mm, 3/8”, 9/16” 3/4”, 7/8” hole saw 13, 21, 22mm, NO DRILL 3/4”, 7/8”, †
n 96942 Ø, @, CS, FS, 13, 21, 22mm, NO DRILL
GP, JL, LT n 45300 #, CS, FS, HM, JL, KH, LT n 41936 @, †
Pickup, Sierra, Cab & Chassis 3500 01-07 Series w/34 Wide Frames (Classic)
n n n n
96936 41938 96938 41940
n n n n
96936 41938 96938 41940
n 06958 Ø,GU,HM,RH 18mm, 3/4”, 7/8” –
83-84
35 n 37152 CN,GU,SB n 37042 CN,GU,SB
n 88001 CN,GU,SB 85-93 S-15 & Sonoma Pickup w/Rear Fascia & No Step Bumper 85-97 S-15 & Sonoma Pickup w/Standard Box & Step Bumper, Inc. ZR2 & Highlander Pkg.
15, 18, 21mm, 9/16", 11/16", 3/4", T50
S-15 & Sonoma Pickup w/Rear Fascia & No Step Bumper
6
1/4”, 1/2”, 5 9/16”
6.5 40
n 33053 Ø,GU
35 n 37152 CN,GU,SB
3.5 6
45
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 40
n 33053 Ø,GU
18mm, 3/4”, NO DRILL 7/8”
3.5 6
45
7/16", 1/2" 40
11/16”
15
16 35 –
17/32”
12
17/32”
12 12 12 15
30 15 40 15 40 – 16 35
15
16 35 –
15
16 35 –
21mm, 13/16”, 7/8” 21mm, 13/16”, 7/8” 21, 24mm, 13/16”, 7/8” 3/4”
@
3/4”
@,CC, †
13/16”, 7/8” 9/16”
@,CC
13/16”, 7/8” 9/16”
@, †
21mm, 9/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8” 21, 24mm, 11/16” 13/16”, 7/8”
30 85262
–
78058
BN,RD
85219
–
–
–
–
–
–
–
–
78058
–
–
–
78058
–
–
74178
78058
BN
–
74178
78058
BN
–
78058
BN
–
74178 n 33055 Ø,†
94-97 06996
18mm, 3/4”, NO DRILL 7/8”
16 35 –
17/32”
74051
n 37042 CN,GU,SB 15, 18, 21mm, 9/16", 11/16", 3/4", T50
1/4”, 1/2”, 5 9/16”
7/16", 1/2" 40
n 06958 Ø,GU,HM,RH 18mm, 3/4”, 7/8” –
n 88001 CN,GU,SB
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
15
13/16”, 7/8” 9/16”
n 96947 @ 83-84
9/16”
@,CC @, †
n 96940 @, †
S-15 & Sonoma Pickup w/Rear Fascia & No Step Bumper S-15 & Sonoma Pickup w/Standard Box & Step Bumper
9/16”
13/16”, 7/8” 9/16”
n 41936 @, †
30 85262 30 15 40 15 40 – 16 35
3/4”
n 96947 @
18 60
12 12 12 15
@ @,CC, †
n 96940 @
Pickup, Sierra, Cab & Chassis 3500 07-13 HD w/34 Wide Frames (New Body Style)
3/4”, 7/8” 13, 19, 21, 22mm, 3/8”, 9/16” 18 3/4”, 7/8” hole saw 3/4” 17/32” 12
OEM REPLACE.
BN,RD
3/4”, 7/8”
FOOTNOTES
78058
DRILL BITS
16 20 85262
GP, JL, LT, †
WRENCHES
15
FOOTNOTES
12 20 n 41942 Ø, @, CS, FS, 13, 21, 22mm, NO DRILL
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
13, 18, 19mm, NO DRILL 3/4”, 7/8”
3.5 6
40
74178
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
STANDARD WIRE
3/4”, 7/8”
T-CONNECTOR
JL, LT
WT. DISTRIB. INSTALL TIME
n 44563 Ø, CS, FS, GP, 13, 21, 22mm, NO DRILL
11-13
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
WT. CARRYING
Pickup, Sierra 3500 HD 6.6 ft. Bed, 2 & 4 WD (New Body Style)
YEAR
MODEL
Pickup, Sierra 2500 HD 8 ft. Bed, 2 & 4 WD (New Body Style)
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
199
GMC
GMC
198
REESE TOWPOWER
REESE TOWPOWER
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
HITCH NUMBER
HITCH NUMBER
DRILL BITS
WRENCHES
HITCH NUMBER
n 06958 Ø,GU,RH
98-04
1983 84-91 84-91 92-94 85-94
n n n n n
Safari Extended Body
90-05
96-99
88002 88002 88002 88002 06227
18mm, 3/4”, 7/8” –
–
1/2”
–
3/4”
1/2”
3.5 5 20
35 n 37152 AF, CN, GU, ST 15,17,18,
1/4”, 1/2”, 5 19,21, 9/16” 22mm,T-50, 9/16”,3/4” n 37042 AF, CN, GU, ST 15,17,18, 1/4”, 1/2”, 5 19,21, 9/16” 22mm,T-50, 9/16”,3/4”
6
n 44062 CN,GU
3/4”
NO DRILL
3.5 5
20
6.5 40
74216
30 30 30 30 30
n n n n n
–
3/4”
1/2”
–
3/4”
1/2”
Ø,CR,HM
14mm, 15mm
NO DRILL
n 06037 Ø,GP,HC n 06227 Ø,CR,HM
14mm, 15mm
NO DRILL
14mm, 15mm
NO DRILL
30 30 n 51029 Ø,CS,GP
n 06037 Ø,GP,HC
14mm, 15mm
NO DRILL
30 n 37152 AF
n 88001 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
7/16", 1/2" 0
n 06099 Ø,HM
7/8”
NO DRILL
n 37042 AF
15 n l n n
51023 37051 37041 37152
Ø,HM HM HM HM
n 37042 HM 15, 18, 21mm, 9/16", 11/16", 3/4", T50
1/2”
40
7/16", 1/2" 40
15, 18, 21mm, 9/16", 11/16", 3/4", T50 3/4”
n 88001 HM
3/4”
3.5 6
3.5 6 30
33014 33014 33014 33014 33057
Ø
18mm
NO DRILL
Ø
18mm
NO DRILL
3.5 3.5 3.5 3.5 3.5
6 6 6 6 6
60 60 60 60 45
74427 74427 74427 – –
78058 78058 78058 78058 78058
–
– – – – –
–
78058
–
–
74659
78013
HG
74886
Ø
18mm
NO DRILL
Ø
18mm
NO DRILL
Ø,CR,HM
15, 17mm, 3/4”
NO DRILL
15, 17mm, 3/4” 15, 17mm
1/2”, 9/16” 3.5 6
45
NO DRILL
3.5 6
30 30
n 33057 CR,HM
15, 17mm
NO DRILL
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 3/4”, 7/8”
1/4”, 1/2”, 5 9/16”
6
n 44010 Ø,CS,GP
1/4”, 1/2”, 5 9/16”
6.5 65
n 33057 Ø,CS,GP
15, 17mm, 3/4”
NO DRILL
3.5 6
NO DRILL
5 5 3/4” 1/2” 5 15,17,18, 19,21, 1/4”, 1/2”, 5
3/4”
NO DRILL
5
10 20
1/2”
10 15 6 35 6 35 6
n 37004 Ø,HM
3/4”
n 44028 Ø,HM
3/4”, 7/8”
NO DRILL
5
10 30 n 41921 @,HM, †
22mm,T-50, 9/16” 9/16”,3/4” 15,17,18, 19,21, 1/4”, 1/2”, 5 22mm,T-50, 9/16” 9/16”,3/4”
n 06099 Ø,HM
7/8”
7/16", 1/2" 30
NO DRILL
15 n l n n
51023 37051 37041 37152
Ø,HM HM HM HM
n 37042 HM n 88001 HM
15, 18, 21mm, 9/16", 11/16", 3/4", T50
7/16", 1/2" 30
5 3/4” 1/2” 5 3/4” 1/2” 5 15,17,18, 19,21, 1/4”, 1/2”, 5 3/4”, 7/8”
NO DRILL
22mm,T-50, 9/16” 9/16”,3/4” 15,17,18, 19,21, 1/4”, 1/2”, 5 22mm,T-50, 9/16” 9/16”,3/4”
10 15 6 35 6 35 6
n 37004 Ø,HM
3/4”
NO DRILL
5
10 20
n 44028 Ø,HM
3/4”, 7/8”
NO DRILL
5
10 30 n 41921 @,HM, †
n 45007 Ø,#,HM,TF n 96946 @,HM
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
BN –
13/16”, 15/16” 9/16”
10
12 35 74659
–
HG
–
13/16”, 15/16” 9/16”
10 12 35 74659 12 14 45 10 13 35 74659 85246
–
HG
–
78013
HG
74886
9/16”
10
12 35 85246
–
HG
–
9/16”
10
12 35 85246
–
HG
–
NO DRILL
12 14 45 10 13 35 85246
3/4”
NO DRILL
13/16”, 15/16” 9/16”
HG
6.5 30
n 96921 @,HM
06996
BN
6.5 30
n 96921 @,HM n 45007 Ø,#,HM,TF n 96946 @,HM 00-02
OEM REPLACE.
BN
n 51063 CN,GP,GU
98-04
13, 18, 19mm, NO DRILL 3/4”, 7/8”
FOOTNOTES
STANDARD WIRE
–
n 33055 Ø,†
98-99
WT. DISTRIB. INSTALL TIME
BN
WT. CARRYING
78058
DRILL BITS
74216
WRENCHES
–
FOOTNOTES
BN
HITCH NUMBER
78058
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
74216
DRILL BITS
98-04
WRENCHES
–
FOOTNOTES
BN
STYLE
78058
WT. CARRYING WT. DISTRIB. INSTALL TIME
74216
DRILL BITS
98-04
WRENCHES
–
FOOTNOTES
BN
INSTALL TIME STYLE
78058
FOOTNOTES
74216
IONSTALL TIME STYLE
–
DRILL BITS
BN
WRENCHES
78058
FOOTNOTES
74216
HITCH NUMBER
–
STYLE
BN
13/16”, 15/16” 13/16”, 15/16” 3/4” 13/16”, 15/16”
9/16”
HG
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
78058
S-15 Jimmy Downsize, All Models S-15 Jimmy Downsize, 2 Dr. S-15 Jimmy Downsize, 4 Dr. S-15 Jimmy Downsize, All Models Safari Standard Body
Savana Van Full Size
WIRING
Up to 2500 lb TW Up to 18000 lb GTW T-CONNECTOR
Up to 500 lb TW Up to 5000 lb GTW
96-97
n 88001 CN,GU,ST
Savana Van Full Size
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
74178
YEAR
MODEL
S-15 & Sonoma Pickup w/Sportside Box & Non-Towing Bumper S-15 & Sonoma Pickup w/Rear Fascia & No Step Bumper S-15 & Sonoma Pickup All, Except Sportside Box w/Non-Towing Bumper & Standard Box w/Rear Fascia S-15 & Sonoma Pickup w/Rear Fascia & No Step Bumper S-15 & Sonoma Pickup w/Sportside Box & Non-Towing Bumper S-15 & Sonoma Pickup w/Standard Box & Step Bumper, Inc. ZR2, Highlander Pkg. & Crew Cab
APPLICATIONS GUIDE
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
201
GMC
GMC
200
REESE TOWPOWER
REESE TOWPOWER
HM HM
n 37042 HM
22mm,T-50, 9/16” 9/16”,3/4” 15,17,18, 19,21, 1/4”, 1/2”, 5 22mm,T-50, 9/16” 9/16”,3/4”
10 15 6 35 6 35 6
3/4”
NO DRILL
5
10 20
n 44028 Ø,HM
3/4”, 7/8”
NO DRILL
5
10 30 n 41921 @,HM, †
APPLICATIONS GUIDE
n 06099 Ø,HM
04-13
n 45007 Ø,#,HM,TF n 96946 @,HM
7/16", 1/2" 30 NO DRILL
15 n 51023 Ø,HM
3/4”, 7/8”
NO DRILL
5
10 15
n 37004 Ø,HM
3/4”
NO DRILL
5
10 20 n 41921 @,HM, †
l 37051 HM
3/4”
1/2”
5
6
35
n 44028 Ø,HM
3/4”, 7/8”
NO DRILL
5
10 30 n 96921 @,HM
n 37041 HM n 37152 HM
3/4”
1/2”
5
1/4”, 1/2”, 5 9/16”
6 6
35
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
n 37042 HM n 88001 HM
15, 18, 21mm, 9/16", 11/16", 3/4", T50
1/4”, 1/2”, 5 9/16”
n 45007 Ø,#,HM,TF n 96946 @,HM
Sonoma GT w/Rear Fascia & No Step Bumper Suburban Suburban Suburban
92-93
n 33055 Ø,†
73-84 85-91 92-99
n 37152 – n 37042 – n 51012 HM n 51012 HM
10-13 99-10
OEM REPLACE.
FOOTNOTES
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
12 35 78029
–
HG
–
9/16”
10
12 35 78029
–
HG
–
NO DRILL
13/16”, 15/16”
9/16”
12 14 45 10 13 35 78029
13/16”, 15/16” 13/16”, 15/16” 3/4”
9/16”
10
12 35 78029
78058
HG
74886
9/16”
10
12 35 78029
–
HG
–
NO DRILL
12 14 45 10 13 35 78029
13/16”, 15/16”
9/16”
n 88001 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
7/16", 1/2" 30
n 06391 Ø,HM
18,19mm, 3/4”
NO DRILL
25 n 51193 Ø,HM
n 51185 Ø,HM
18,19mm, 3/4”
NO DRILL
25
74178
78058
–
–
3.5 6
40
74178
78058
–
–
7.5 40 7.5 40 10 30
74225 74178 74180
78058 78058 78058
BN BN
7/8”
5 5 1/2”, 9/16” 6
BN
– – –
74178 85716
78058 78104
CH
85716 16 35 –
78104 –
–
85779 –
–
–
1/4”, 1/2”, 5 9/16”
6
n 44605 – n 44605 – n 37074 HM
1/4”, 1/2”, 5 9/16”
6.5 30
n 44096 HM
7/8”
1/2”, 9/16” 5
7
1/2”, 9/16” 5
7 30 7 30
n 44656 HM
7/8”
1/2”, 9/16” 5
7.5 30
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 7/8” 7/8”
1/2”, 9/16” 5
3/4”, 7/8” 3/4”, 7/8”
1/2”
1/2”
30
74180
18,19mm, 3/4”
NO DRILL
3.5 4 30
n 44637 Ø,HM
18,19mm, 3/4” NO DRILL
3.5 4
30
n 44630 Ø,†,HM
18,19mm, 3/4” NO DRILL
3.5 4
30 n 41940 @, †
n 41940 @, †
99-10
n 41940 @, †
99-10
n 96940 @ n 96947 @
06996
10
40
n 96940 @ n 96947 @ Topkick C6500 Cab & Chassis w/34 Wide Frames
9/16”
3.5 6
13, 18, 19mm, NO DRILL 3/4”, 7/8” 13, 18, 19mm, NO DRILL 3/4”, 7/8”
n 96940 @ n 96947 @ Topkick C5500, Cab & Chassis w/34 Wide Frames
74886
74051 n 33055 Ø,GP
Terrain All, Except V6 Models Topkick C4500 Cab & Chassis w/34 Wide Frames
13/16”, 15/16” 13/16”, 15/16” 3/4”
7/16", 1/2" 30
92-93
91-92 10-13
–
6.5 30
Sonoma GT
Syclone Terrain All Models
78058
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
21mm, 13/16”, 7/8” 9/16”
15
21mm, 13/16”, 7/8” 9/16”
15 16 35 – 15 16 35 –
–
15
16 35 –
–
15 16 35 – 15 16 35 –
–
15
16 35 –
–
15 16 35 – 15 16 35 –
–
21, 24mm, 11/16” 13/16”, 7/8” 21mm, 13/16”, 7/8” 9/16” 21mm, 13/16”, 7/8” 9/16” 21, 24mm, 11/16” 13/16”, 7/8” 21mm, 13/16”, 7/8” 9/16” 21mm, 13/16”, 7/8” 9/16” 21, 24mm, 13/16”, 7/8”
11/16”
BN
CH
– 85779
– –
–
–
–
– –
–
–
–
–
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
Savana Van Full Size
15, 18, 21mm, 9/16", 11/16", 3/4", T50 7/8”
78029
6.5 30
n 96921 @,HM n 88001 HM
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
n 37004 Ø,HM
STANDARD WIRE
NO DRILL
1/2”
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
5 5 3/4” 1/2” 5 15,17,18, 19,21, 1/4”, 1/2”, 5 3/4”, 7/8”
3/4”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW T-CONNECTOR
Ø,HM HM
DRILL BITS
51023 37051 37041 37152
WRENCHES
15 n l n n
FOOTNOTES
DRILL BITS NO DRILL
HITCH NUMBER
7/8”
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
n 06099 Ø,HM
2003
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Savana Van Full Size
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
203
GMC
GMC
202
REESE TOWPOWER
REESE TOWPOWER
n 96940 @
21mm, 9/16” 13/16”, 7/8” 21, 24mm, 11/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8”
15
16 35 –
–
–
–
15
16 35 –
15
16 35 –
–
–
–
15
16 35 –
–
–
–
15
16 35 –
n 96940 @ n 96947 @ Van, G-Series Full Size
n 51003 BF
87-95
Van, G-Series Vandura & Rally Full Size w/Lo-Mount Taillights
1996
Yukon Old Body Style
92-00
n 51003 BF n 37152 – n 37042 – n 51012 HM n 51012 HM n 88001 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
n 37042 – n 51201 Ø,CN,HM
n 37042 – n 51201 Ø,CN,HM
Yukon Denali Old Body Style
n 51012 HM n 51012 HM n 37152 –
01-02
n 37042 – n 51201 Ø,CN,HM
06996
Ø,BF,CV
3/4”, 9/16”
NO DRILL
5
30 45 30 45 30
7.5 30 6
n 44011 Ø,BF,CV n 37074 HM
3/4”, 9/16”
NO DRILL
7/8”
1/2”, 9/16” 6
7.5 45 10 30
1/4”, 1/2”, 5 9/16”
6.5 30
n 44096 HM
7/8”
1/2”, 9/16” 5
7
1/2”, 9/16” 5
7 30 7 30
n 44656 HM
7/8”
1/2”, 9/16” 5
7.5 30
3/4”, 9/16” NO DRILL
5
1/4”, 1/2”, 5 9/16”
15,17,18, 19,21, 22mm, T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 7/8” 7/8”
1/2”, 9/16” 5
–
78058
–
–
74486
78058
–
–
74486
78058
–
–
74180
78058
BN
–
78058
BN,RD
85219
78058
BN,RD
85219
74180
78058
BN,RD
–
74682
78058
RD
85219
30
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 22mm, 7/8”
1/4”, 1/2”, 5 9/16”
6
n 37072 Ø,CN,HM
22mm, 7/8”
NO DRILL
6
10 20
1/4”, 1/2”, 5 9/16”
6.5 30
n 44095 Ø,CN,HM
22mm, 7/8”
NO DRILL
5
10 20
5
10 15
l 44668 Ø,CN,HM
22mm, 7/8”
NO DRILL
6
10 15
NO DRILL
74682
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 22mm, 7/8”
1/4”, 1/2”, 5 9/16”
6
n 37072 Ø,CN,HM
22mm, 7/8”
NO DRILL
6
10 20
1/4”, 1/2”, 5 9/16”
6.5 30
n 44095 Ø,CN,HM
22mm, 7/8”
NO DRILL
5
10 20
5
10 15
l 44668 Ø,CN,HM
22mm, 7/8”
NO DRILL
6
10 15
NO DRILL
74682
85262
n 37042 –
Yukon Denali New Body Style w/Amber Turn Signals
NO DRILL NO DRILL
10 7.5 10 7.5 10
7/16", 1/2" 30
n 37152 –
99-00
3/4”, 9/16” 3/4”, 9/16”
NO DRILL NO DRILL
85262 n 37152 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
Ø,BF,CV Ø,BF,CV
3/4”, 9/16” 3/4”, 9/16”
7/16", 1/2" 30
Yukon New Body Style w/Amber Turn Signals 03-06
n 88001 –
7.5 30
5 5 5 5 5
Ø,BF,CV Ø,BF,CV
–
74180 n 37152 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
5
35365 44011 35365 44011 35365
7/16", 1/2" 30
Yukon New Body Style w/Amber Turn Signals 00-02
n 88001 –
3/4”, 9/16” NO DRILL
n n n n n
–
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
1/4”, 1/2”, 5 9/16”
6
n 37074 HM
7/8”
1/2”, 9/16” 6
10 30
1/4”, 1/2”, 5 9/16”
6.5 30
n 44096 HM
7/8”
1/2”, 9/16” 5
7
1/2”, 9/16” 5
7 30 7 30
n 44656 HM
7/8”
1/2”, 9/16” 5
7.5 30
1/4”, 1/2”, 5 9/16”
6
n 37072 Ø,CN,HM
22mm, 7/8”
NO DRILL
6
10 20
1/4”, 1/2”, 5 9/16”
6.5 30
n 44095 Ø,CN,HM
22mm, 7/8”
NO DRILL
5
10 20
5
10 15
l 44668 Ø,CN,HM
22mm, 7/8”
NO DRILL
6
10 15
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 7/8” 7/8”
1/2”, 9/16” 5
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 22mm, 7/8”
NO DRILL
30
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
Van, G-Series Full Size
78-86
21mm, 9/16” 13/16”, 7/8” 21, 24mm, 11/16” 13/16”, 7/8”
OEM REPLACE. –
FOOTNOTES –
n 41940 @, †
99-10
STANDARD WIRE –
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
16 35 –
DRILL BITS
15
WRENCHES
21mm, 9/16” 13/16”, 7/8”
FOOTNOTES
n 41940 @, †
HITCH NUMBER
WT. CARRYING
99-10
n 96947 @ Topkick C8500 Cab & Chassis w/34 Wide Frames
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Topkick C7500 Cab & Chassis w/34 Wide Frames
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
205
GMC
GMC
204
REESE TOWPOWER
REESE TOWPOWER
15, 18, 21mm, 9/16", 11/16", 3/4", T50
Accord 2 Dr. Accord 4 Dr., Including Hybrid Accord 2 Dr., 2.4L I4 Engine Accord 2 Dr., 3.5L V6 Engine Accord 4 Dr., 2.4L I4 Engine Accord 4 Dr., 3.5L V6 Engine Accord Crosstour All Models Civic 4 Dr.
n 51201 Ø,CN,HM
03-05 06-07 06-07 08-12 08-12 08-12 08-12 10-12 92-98
77019 77013 77165 77161 51167 77161 51167 77161 51167 77161 51167 77177 77208 77177 77208 77177 77208 77177 77208 77224 77025
06996
–
14, 17mm, 7/8”
Ø,HM
10, 14, 17mm, 9/16” NO DRILL
1/2”
Ø,JR
3/4”
NO DRILL
Ø,HR,JR
11/16”, 3/4”
9/16”
Ø,HR,JR
11/16”, 3/4”
9/16”
Ø,HR,JR
11/16”, 3/4”
9/16”
Ø,HR,JR
11/16”, 3/4”
9/16”
Ø,HR,JR
11/16”, 3/4”
9/16”
Ø,HR,JR
11/16”, 3/4”
9/16”
Ø,HR,JR
11/16”, 3/4”
9/16”
Ø,HR,JR
11/16”, 3/4”
9/16”
Ø,HM,JR,KH
10mm, 11/16”
NO DRILL
Ø,HM,JR,KH
10mm, 11/16”
NO DRILL
Ø,HM,JR,KH
10mm, 11/16”
NO DRILL
Ø,HM,JR,KH
10mm, 11/16”
NO DRILL
Ø,HM,JR,KH
10mm, 11/16”
NO DRILL
Ø,HM,JR,KH
10mm, 11/16”
NO DRILL
Ø,HM,JR,KH
10mm, 11/16”
NO DRILL
Ø,HM,JR,KH
10mm, 11/16”
NO DRILL
Ø,HM,JR,KH
10, 13, 17mm
NO DRILL
Ø, EP
9/16”, 7/8”
NO DRILL
85219 –
n 44095 Ø,CN,HM
22mm, 7/8”
NO DRILL
5
10 20 n 96930 @,CN
22mm, 1/2” 13/16”, 7/8”, 3/4” 21mm, 3/4” 1/2”
10
12 35 85262
–
BN
–
l 44668 Ø,CN,HM
22mm, 7/8”
NO DRILL
6
10 15 n 45013 #,TF
12
14 50
RD
RD
OEM REPLACE.
BN
FOOTNOTES
STANDARD WIRE 78058 –
DRILL BITS
74682 12 35 85262
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
WRENCHES
DRILL BITS
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
10
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 30
5
10 15
NO DRILL
22mm, 7/8”
NO DRILL
6
10 20 n 41930 @,CN, †
n 44095 Ø,CN,HM
22mm, 7/8”
NO DRILL
5
10 20 n 96930 @,CN
l 44668 Ø,CN,HM
22mm, 7/8”
NO DRILL
6
10 15 n 45013 #,TF
22mm, 1/2” 13/16”, 7/8”, 3/4”
10
74682 12 35 85262
78058 –
BN
85219 –
22mm, 1/2” 13/16”, 7/8”, 3/4” 21mm, 3/4” 1/2”
10
12 35 85262
–
BN
–
12
14 50
78058 –
RD BN
85219 –
85262
n 37042 –
n n n n n n n n n n n n n n n n n n n n n
22mm, 1/2” 13/16”, 7/8”, 3/4”
10 20
7/16", 1/2" 30
n 37152 –
Accord 4 Dr., Including Hybrid
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 22mm, 7/8”
NO DRILL
6
n 37072 Ø,CN,HM n 44095 Ø,CN,HM
22mm, 7/8”
1/4”, 1/2”, 5 9/16”
22mm, 7/8”
NO DRILL
6 5
10 20 10 20 n 41930 @,CN, †
1/4”, 1/2”, 5 9/16”
6.5 30
l 44668 Ø,CN,HM
22mm, 7/8”
NO DRILL
6
10 15 n 96930 @,CN
5
10 15
01-02
90-93 94-97 98-02 03-05
6
n 41930 @,CN, †
n 37072 Ø,CN,HM
n 88001 –
2 & 4 Dr. 2 & 4 Dr. 2 & 4 Dr. 2 Dr.
10 15
03-06
n 51201 Ø,CN,HM
Accord Accord Accord Accord
5
NO DRILL
NO DRILL
85262
n 37042 –
HONDA
6.5 30
22mm, 7/8”
7/16", 1/2" 30
n 37152 –
Yukon XL Denali
1/4”, 1/2”, 5 9/16”
n 37072 Ø,CN,HM
20 30 15 25 25 25 25 25 25 25 25 30 30 45 30 30 30 45 30 40 15
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 22mm, 7/8”
NO DRILL
22mm, 1/2” 13/16”, 7/8”, 3/4”
10
74682 12 35 85262
22mm, 1/2” 13/16”, 7/8”, 3/4”
10
12 35 85262
– 74660 74660 74718
78013 78104 78104 78013
CG
– – – –
78002
78104
HG
–
74713
–
HG
–
78002
78104
HG
–
74697
78104
CH
–
74697
78104
CH
–
74697
78104
CH
–
74697
78104
CH
–
85721 –
78104 78104
CH
– –
–
78013
– HG HG
92-95 Only 96-98 Only
–
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
15, 18, 21mm, 9/16", 11/16", 3/4", T50
6
T-CONNECTOR
n 88001 –
1/4”, 1/2”, 5 9/16”
WT. DISTRIB. INSTALL TIME
n 51201 Ø,CN,HM
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 22mm, 7/8”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW WT. CARRYING
n 37042 –
Yukon XL, All Styles
WRENCHES
FOOTNOTES
HITCH NUMBER
00-02 n 37152 –
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Yukon XL, All Styles
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
207
GMC - HONDA
GMC - HONDA
206
REESE TOWPOWER
Civic Civic Civic Civic Civic
3 Dr. Hatchback 2 & 4 Dr. 2 & 4 Dr. Si Models Only 2 Dr., Except Si Models
Civic 4 Dr., Except Hybrid & Si Models Civic 4 Dr., Si Models
93-98
96-00 99-00 01-05 02-05 06-12 06-12 06-12 06-12 06-12
CR-V CR-V
97-01 02-06
CR-V, All Styles
07-11
CRV, All Styles
12-13
Element
03-04
Element All, Except SC
05-06
Element SC Models Only Element All, Except SC
05-06 07-08
Element SC Models Only Element All, Except SC Fit All, Inc. Sport Fit Odyssey Odyssey Odyssey Odyssey Passport
07-10 09-11 07-08 09-13 95-98 99-04 05-10 11-12 94-97
Passport w/Door Mounted Spare
98-01
n n n – n n n n n n n n n n n n n n n
77194 77025 77116 77033 77139 51165 77139 51165 77139 51165 77139 51165 77139 51165 77164 77149 51166 77147 51168
9/16”, 7/8”
NO DRILL
X
9/16”, 11/16”
7/16”
Ø
9/16”, 7/8”
NO DRILL
–
9/16”, 7/8”
1-1/8”
TA
3/4”, 7/8”
1/2”
Ø,HM,JR
10mm, 3/4”, 9/16” NO DRILL
Ø,HM,JR
10mm, 3/4”, 9/16” NO DRILL
Ø,HM,JR
10mm, 3/4”, 9/16” NO DRILL
Ø,HM,JR
10mm, 3/4”, 9/16” NO DRILL
Ø,HM,JR
10mm, 3/4”, 9/16” NO DRILL
Ø,HM,JR
10mm, 3/4”, 9/16” NO DRILL
Ø,HM,JR
10mm, 3/4”, 9/16” NO DRILL
Ø,HM,JR
10mm, 3/4”, 9/16” NO DRILL
Ø,HM,JR
10mm, 3/4”, 9/16” NO DRILL
Ø,HM,JR
10mm, 3/4”, 9/16” NO DRILL
Ø,RC
3/4”
NO DRILL
Ø,BY,JR
3/4”
NO DRILL
Ø,BY,JR
3/4”
NO DRILL
Ø,JR
3/4”, 11/16”
NO DRILL
Ø,JR
3/4”, 11/16”
NO DRILL
20 15 15 30 30 30 30 30 30 30 30 30 30 30 20 20 20 20 20
77034 77034 77034 77034
–
3/4”, 7/8”
7/16”
Ø
3/4”, 7/8”
7/16”
–
3/4”, 7/8”
7/16”
Ø
3/4”, 7/8”
7/16”
n 77034 – n 77034 Ø
3/4”, 7/8”
7/16”
3/4”, 7/8”
7/16”
3/4”, 7/8”
7/16”
n 77034 – n 77153 Ø n 77198 Ø,HM
12, 13mm, 11/16” NO DRILL 11/16”
NO DRILL
40 l 97209 Ø,HM,JR,SV 10, 17mm, 11/16”
98-02
Pilot
03-08
Pilot Prelude All Models Prelude All Models Prelude All Models Ridgeline
09-11 92-96 97-00 01-02 06-13
H3
06-10
HUMMER
HM,JR
14mm, 3/4”
1/2”
Ø,HM,JR
18mm
NO DRILL
Ø,HM,JR
18mm
NO DRILL
Ø,HM,JR
18mm
NO DRILL
Ø
17, 19mm, NO DRILL 11/16”, 5/8” 19mm, 3/4”, 7/8” NO DRILL
n 06366 Ø
30 20 l 51156 Ø,RT,HM,JR 18mm 20 l 51156 Ø,RT,HM,JR 18mm 20 l 51156 Ø,RT,HM,JR 18mm 30 15 n 37152 Ø
n 06356 Ø,HM
19mm, 3/4”, 7/8” NO DRILL
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
NO DRILL NO DRILL
l 51139 Ø,RT,JR
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
OEM REPLACE.
FOOTNOTES
STANDARD WIRE
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
T-CONNECTOR
CG
– – – – –
–
78013
–
–
74697
78013
CG
–
78013
–
– – –
–
78013
–
–
HG
– –
3.5
30
74660 74660
78013 78013
HG
– –
3.5
25
74704
78013
CG
–
l 44675 Ø,HM,JR,SV 10, 17mm,
NO DRILL
3.5 0
40
l 44612 Ø
11/16” 3/4” 7/8”
NO DRILL
3.5
30
74660
78013
HG
–
l 44612 Ø
3/4” 7/8”
NO DRILL
3.5
30
–
78104
–
–
l 44612 Ø,EP l 44612 Ø
3/4” 7/8”
NO DRILL NO DRILL
3.5 3.5
35 30
– 78099
78104 78104
–
3/4” 7/8”
CH
– –
l 44612 Ø,EP l 44612 Ø
3/4” 7/8”
NO DRILL
3/4” 7/8”
NO DRILL
3.5 3.5
35 30
78099 78099 74697 74697 74660 74660 74715 85747 74477
78104 78104 78013 78013 78013 78013 78013 78013 78013
BN,HG
– – – – – – – – –
74217
78013
BN,HG
–
3.5 5 15 3.5 5 15 3.5 5 15 6
1/4”, 1/2”, 5 9/16”
6.5 15
10, 17, 19mm NO DRILL
78013 78013 78013 78013 78013
40
1/4”, 1/2”, 5 9/16”
NO DRILL
– – – – 74714
–
n 44643 Ø,BY,HM,JR 11/16”, 7/8” NO DRILL
l l l n
44174 44174 44174 33040
Ø,HM,JR
3.5 5 30
5
6 20
17mm, 11/16” NO DRILL
18mm
NO DRILL
Ø,HM,JR
18mm
NO DRILL
Ø,HM,JR
18mm
NO DRILL
Ø
19mm
NO DRILL
n 33041 Ø 10, 14, 17, 19mm
78013
–
–
3.5 0
15 n 51159 Ø,CS,GP,JR
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS NO DRILL
–
93-95 Only 96-98 Only –
l 44575 Ø,HM,JR
25 25 25 06953 06398 06398 06398 06057
78104
25
25 25
n n n n n
06996
NO DRILL
–
3.5 0
25 25 25 25
n 37042 Ø Passport w/Under Vehicle Spare
WRENCHES
FOOTNOTES
HITCH NUMBER
l 51205 Ø,HM,JR,TJ 17mm, 11/16” NO DRILL
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
15
l 06144 Ø,HM,JR,SV 10, 17mm, 11/16” NO DRILL n n n n
INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
n 77025 Ø
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
n 44589 Ø,CS,GP,JR
19mm, 7/8”, NO DRILL 15/16” 10, 14, 17, NO DRILL 19mm
3.5 5 3.5 5 3.5 5 5
15 15 15 45
CG CG HG HG CH CH
3.5 5
15
74217
78013
BN,HG
–
3.5 5
30
74660
78013
HG
–
85715 – – 74660
78013 78104 78013 78013
–
HG
85780 – – – –
74682
78058
–
n 44528 Ø,JR
10, 17, 19mm NO DRILL
5
6
20
n 44177 Ø
21mm
5
5
25
NO DRILL
CH CH
– –
85219
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
209
APPLICATIONS GUIDE
Civic Hybrid
YEAR
MODEL
Civic 2 Dr. Coupe
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
Civic 2 Dr., Si Models
APPLICATIONS GUIDE
REESE TOWPOWER
HONDA - HUMMER
HONDA - HUMMER
208
REESE TOWPOWER
12-13 06-12
Elantra All Models Elantra All Models, Inc. GT
96-00 01-06
Elantra 4 Dr. Sedan Elantra Touring 5 Dr. Elantra 4 Dr. Sedan Elantra GT, All Styles Entourage Genesis 4 Dr. Sedan
07-10 09-12 11-12 2013 07-09 09-12
Genesis 2 Dr. Coupe Santa Fe Santa Fe
10-11 01-06 07-09
Santa Fe
12, 13mm, 3/4” (x2) NO DRILL
Ø
19mm
NO DRILL
Ø,JR
17, 19mm
NO DRILL
Ø,HM
11/16”
NO DRILL
Ø,HM
11/16”
NO DRILL
Ø,HM
11/16”
NO DRILL
Ø,HM
11/16”
NO DRILL
Ø,JR
NO DRILL
TA
10, 12mm, 17mm, 3/8” 13/16”, 7/8”
1/2”
Ø,HM
14, 17mm, 7/8”
NO DRILL
Ø,HM
14, 17mm, 7/8”
NO DRILL
Ø,JR
17, 19mm
NO DRILL
Ø,GP,JR
17, 19mm
NO DRILL
Ø,HM,JR
11/16”, 3/4”
1/2”
Ø,HM
3/4”, Crowfoot Adaptor NO DRILL
Sonata Sonata Sonata All, Incl. GLS, SE & Limited Tiburon Tucson
02-05 06-10 11-13 03-08 05-09
10mm, 9/16”, 11/16”
1/2”
16mm
NO DRILL
n n n n
77030 77133 77225 77042
l 51088 Ø,RT,GP,JR
14, 17, 19mm NO DRILL
3.5
35
n 51076 Ø n 51206 Ø, HM
16mm
NO DRILL
16mm
NO DRILL
3.5 3.5 5
20 15
n 33037 Ø,GP,JR n 44549 Ø
16mm
n 44639 Ø,HM
16mm
NO DRILL
3.5 3.5
35 20
NO DRILL
3.5 5
15
14, 17, 19mm NO DRILL
15 NO DRILL
78013
–
–
– –
78013 78013
– –
– –
74710 78088 85761 85761 78046 78110
78013 78104 78104 78104 78104
85748 78088 74692
78104 78013 78013
74692 85729
78013 78013
15 20 30 25
78013 78013 78013 78013 78013
10, 18mm, 9/16” NO DRILL
Ø,HM,JR,KH
10, 13mm, 11/16” NO DRILL
TA
9/16”, 3/4”
1/2”
06339 51180 06667 06994 06132
07-12
FX35 FX35
03-08 09-12
n –
FX45 FX50
03-08 09-12
n –
G35 4 Dr. Sedan G37 4 Dr. Sedan I30 I30 I35 JX35, All Styles QX4
07-08 09-12 95-99 00-01 02-04 2013 97-03
EP,GP
13mm, 3/4”
3/4”
EP,GP
13mm, 3/4”
3/4”
TA
7/8”
1/2”
TA
7/8”
1/2”
TA
7/8”
1/2”
Ø,GP.JR
13, 14, 17mm
NO DRILL
Ø,GP.JR
13, 14, 17mm
NO DRILL
Ø,GP, †
16mm
NO DRILL
Ø,GP, †
16mm
NO DRILL
Ø,GP.JR
16mm
NO DRILL
Ø,JR,X
Ø,JR,X
12mm, 19mm
12mm, 19mm
NO DRILL
NO DRILL
25 25 15 15 20
17mm
–
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
NO DRILL
5
– –
CG
– – 85729
CG
85729
CH CG
Factory Tow Package models only CG –
–
–
CG
– – – – –
3.5
25
n 44642 Ø,†,GP
16mm
NO DRILL
3.5 4
15
85722
78013
CH
–
n 44666 Ø,GP,JR n 44573 Ø,HM,JR
16mm
NO DRILL
10, 14, 16mm NO DRILL
3.5 5.25 20 5 5 30
85756
78104
–
–
–
– –
CG CG –
l 44610 Ø
10, 12, 13, 14, NO DRILL 17, 19mm
3.5
40
– 78105
– 78104
CH
l 44610 Ø
10, 12, 13, 14, NO DRILL 17, 19mm
3.5
40
– 78105
– 78104
CH
78108 78108 – – –
78104 78104 78104 78103 78013
–
– – – – –
74218
78013
HG
–
l 44679 Ø,HM l 33050 Ø n 44132 Ø 17mm
BN,CH CH
13, 14, 17mm NO DRILL
45
l 51046 Ø,HM
CH
– – –
n 44582 Ø,GP.JR
45
15
CG CG
n 74710 74710 – 78034
45 45 30 30 30 n 06061 Ø,GP
–
3.5 5.25 30
NO DRILL
Ø,HM
– –
CH
78013
Ø,HM
OEM REPLACE.
74690
74692 17, 19mm
FOOTNOTES
STANDARD WIRE
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
DRILL BITS
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE 20
–
– – – –
–
Veracruz
06996
3.5 4
78013 78013 78013 78013
15
10-13
77204 77204 77028 77028 77028
NO DRILL
– – – –
NO DRILL
12, 14, 17mm, 9/16” 14, 17mm, 7/8”
n n n n n
n n n n n
19mm
60
l 44682 Ø,J,JR n 77090 Ø,†,JR
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
n 44537 Ø,JR
n 06133 Ø,HM 2013 99-01
INFINITI
DRILL BITS
30 15 15 25 25 15 20 n 06659 HM,JR,KH
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
20 20 25 15 15 15 15 20
10-12
Santa Fe Sonata
Tucson
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
77111 77089 51162 77167 77246 77250 77283
DRILL BITS
n n n n n n n
Ø
WRENCHES
77053 77136 77167 77263 77272 77263 77272 77148
FOOTNOTES
n n n l n l n n
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
18mm
NO DRILL
17mm
NO DRILL
17mm
NO DRILL
30 0.525 3.5 5 5.5 20 5 5.5 20
–
CH CH – –
– –
5.5 20
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
211
APPLICATIONS GUIDE
Azera, All Models
HITCH NUMBER
95-99 00-05 06-11 07-11 2012
STYLE
Accent, All Models Accent All Models Accent 4 Dr. Sedan Accent 3 Dr. Hatchback Only Accent, 4 Dr. Sedan
YEAR
MODEL HYUNDAI
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
Accent, 5 Dr. Hatchback
APPLICATIONS GUIDE
REESE TOWPOWER
HYUNDAI - INFINITI
HYUNDAI - INFINITI
210
REESE TOWPOWER
only models 85219 w/ Tow Package
5 6 5
8 30 10 45 10 45
–
78058
–
–
–
78058
–
–
–
INTERNATIONAL Pickup, Full Size
69-75 69-75
ISUZU Amigo w/Door Mounted Spare Axiom w/Under Vehicle Spare
98-00 02-03
n 06366 Ø
19mm, 3/4”, 7/8” NO DRILL
n 33041 Ø n 33055 Ø,† n 06958 Ø,GU,HM,RH 18mm, 3/4”, 7/8” –
96-97
n 33053 Ø,GU
35
n 33055 Ø,† Hombre w/Rear Fascia & No Step Bumper 98-00 98-00 Hombre w/Step Bumper
n 06958 Ø,GU,RH
n 88001 CN,GU,ST Oasis Pickup I-Series All Models
96-99 06-07
n 06953 HM,JR
Pickup I-Series All Models
2008
Rodeo
1991
n 06057 Ø
Rodeo
92-97
n 06057 Ø
Rodeo w/Door (Tailgate) Mounted Spare
98-01
18mm, 3/4”, 7/8” –
15, 18, 21mm, 9/16", 11/16", 3/4", T50 14mm, 3/4”
35 n 37152 AF, CN, GU, ST 15,17,18, 19,21, 1/4”, 1/2”, 5 22mm,T-50, 9/16”,3/4” n 37042 AF, CN, GU, ST 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” n 51063 CN,GP,GU 3/4”
1/2”
BN,HG
– –
NO DRILL
3.5 6
40
74178
78058
BN
–
NO DRILL
3.5 6
45
74178
78058
BN
–
NO DRILL
3.5 6
40
3.5 5
20
74216 74216
78058 78058
BN
NO DRILL
BN
– –
6.5 40
3.5 5 20
6
7.5 25
n 44593 Ø,GP
NO DRILL
6
7.5 25
n 44593 Ø,GP
NO DRILL
6
7.5 25
74660 78001
78013 78013
BN,CG
– –
NO DRILL
6
7.5 25
78001
78013
BN,CG
–
NO DRILL
5
45
–
78013
–
–
NO DRILL
5
45
74477
78013
BN,HG
–
3.5 5
15
74217
78013
BN,HG
–
3.5 5
15
74217
78013
BN,HG
–
74217 74661
78013 78013
BN,HG
7.5 45
BN,HG
– –
–
78013
–
–
78013
HG
–
19mm
15
n 44621 Ø
19mm, 3/4”, 7/8” NO DRILL
15
n 33041 Ø
19mm, 7/8”, NO DRILL 15/16” 19mm, 7/8”, NO DRILL 15/16”
19mm, 3/4”, 7/8” NO DRILL
15 30
n 33043 –
14, 17, 19mm, 1/2” 1/2”
5
14, 17, 19mm
1/2”
9/16”, 3/4”, 7/8”, NO DRILL various metric
30 n 37152 –
15, 18, 21mm, 7/16", 1/2" 45 9/16", 11/16", 3/4", T50 9/16”, 3/4”, 7/8”, NO DRILL 30 n 37152 – various metric
n 37042 – n 51001 – 15, 18, 21mm, 9/16", 11/16", 3/4", T50
7/16", 1/2" 45
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
21, 22mm, 11/16” 21, 22mm, 11/16”
NO DRILL
n 33040 Ø
n 51001 –
06996
78013 78013
30
n 06366 Ø n 06130 Ø
n 88001 –
– 74217
n 33040 Ø
n 06356 Ø,HM
n 06954 Ø,GP
20
30
n 37042 –
91-96 Cherokee Downsize, All Models (Will Not Fit Grand Cherokee)
1/2”
3/4”
3.5 5
30
n 06366 Ø
n 88001 –
1/4”, 1/2”, 5 9/16”
n 44062 CN,GU
1” hole saw
21, 22mm, 11/16” 21, 22mm, 11/16” 19mm
17, 19mm, NO DRILL 11/16”, 5/8” 17, 19mm, NO DRILL 11/16”, 5/8” 19mm, 3/4”, 7/8” NO DRILL
n 06954 Ø,GP
9/16”
6
19mm, 7/8”, 15/16” 13, 18, 19mm, 3/4”, 7/8” 18mm, 3/4”, 7/8” 13, 18, 19mm, 3/4”, 7/8”
74216
n 51074 Ø,GP
JEEP 84-90 Cherokee Downsize, All Models (Will Not Fit Grand Cherokee)
13, 18, 19mm, NO DRILL 7/8”
7/16", 1/2" 40
n 51074 Ø,GP
98-04 Rodeo w/Under Vehicle Spare & Except Models Equipped w/3.5L Rodeo Sport 2 Dr., w/Door Mounted Spare 01-03 92-02 Trooper All Models
1/2” 1/2”
15
Hombre w/Rear Fascia & No Step Bumper 96-97 Hombre w/Step Bumper
3/4”, 7/8” 3/4”, 7/8”
OEM REPLACE.
STANDARD WIRE 78058
FOOTNOTES
T-CONNECTOR 74682
WT. DISTRIB. INSTALL TIME
10 15 10 15
WT. CARRYING
6 6
l 44674 Ø, HM l 44674 Ø, HM
DRILL BITS
NO DRILL NO DRILL
08-10
WRENCHES
19mm 19mm
QX56
FOOTNOTES
only models 85219 w/ Tow Package
HITCH NUMBER
78058
19mm
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
74682
l 37091 Ø
DRILL BITS
10 15
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
6
04-07
n 33065 FP n 37087 FP n 37081 M
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
NO DRILL
QX56
Pickup, Full Size w/Deep Drop Bumper
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 18mm, 3/4”, 13/16”, 7/8”
1/4”, 1/2”, 5 9/16”
6
n 33002 –
3/4”, 13/16”, NO DRILL 7/8”
3.5 5.5 45
1/4”, 1/2”, 5 9/16”
6.5 35
n 44088 –
18mm, 7/8”, NO DRILL 13/16”, 3/4”
3.5 5
NO DRILL
HG
40
3.5 5 40 74672
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 18mm, 3/4”, 13/16”, 7/8”
1/4”, 1/2”, 5 9/16”
6
n 33002 –
3/4”, 13/16”, NO DRILL 7/8”
3.5 5.5 45
1/4”, 1/2”, 5 9/16”
6.5 35
n 44088 –
18mm, 7/8”, NO DRILL 13/16”, 3/4”
3.5 5
NO DRILL
74476
40
3.5 5 40 74476
HG
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
213
APPLICATIONS GUIDE
APPLICATIONS GUIDE
REESE TOWPOWER
INFINITI - JEEP
INFINITI - JEEP
212
REESE TOWPOWER
REESE TOWPOWER
n 37042 – n 51001 – n 88001 – 06-10 07-10 11-12 07-10 1993
n n n n n
06378 06428 06428 06428 06081
Ø
NO DRILL
Ø,GP
16mm, 15/ 16”
5/8”
Ø,GP
16mm, 15/ 16”
5/8”
Ø,EP,GP
16mm, 15/ 16”
5/8”
Ø
18, 19mm
1/2”
20 15 15 30 30
n 06081 Ø
94-98
6.5 35
n 44088 –
18mm, 7/8”, NO DRILL 13/16”, 3/4”
3.5 5
NO DRILL
3.5 15,17,18, 19,21, 1/4”, 1/2”, 5 6
5 7.5 20 3.5 15
16mm, 15/16” NO DRILL
22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 18, 19mm
30
9/16”
1/4”, 1/2”, 5 9/16” NO DRILL
6.5 35
33095 44555 44661 44555 33006
Ø,GP,TU
16,22mm
Ø,EP,GP
16mm, 15/16” NO DRILL
Ø
18, 19mm
NO DRILL
5 7.5 20 3.5 15 3.5 15 3.5 30 3.5 5 45
n 44093 Ø
18, 19mm
NO DRILL
3.5 5
n n n n n
Ø
3/4”
Ø,GP
16mm, 15/16” NO DRILL
NO DRILL NO DRILL
78044 74705 85764 74705 74667
HG
78013 78104 78104 78104 78104
n 51010 Ø
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 18, 19mm
– BN,CH GC
85253 – – – –
3.5 5 20
1/4”, 1/2”, 5 9/16”
6
n 33006 Ø
18, 19mm
NO DRILL
3.5 5
45
1/4”, 1/2”, 5 9/16”
6.5 35
n 44093 Ø
18, 19mm
NO DRILL
3.5 5
20
NO DRILL
BN,CG BN,CH
20
74667
30 n 37152 –
–
3.5 5 40
n 51085 Ø,EP,GP n 37152 –
NO DRILL
16mm, 15/16” NO DRILL
HG
OEM REPLACE.
78013
FOOTNOTES
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
74206
40
7/16", 1/2" 35 1/2”
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
1/4”, 1/2”, 5 9/16”
74668
GC
78104
GC,JM
–
3.5 5 20
7/16", 1/2" 35
74668
Grand Cherokee
1999
n 06966 Ø
15, 18, 21mm, 9/16", 11/16", 3/4", T50 18, 19mm
Grand Cherokee
00-04
n 06966 Ø
18, 19mm
NO DRILL
15 n 51059 Ø
18, 19mm
NO DRILL
3.5 5 15
n 44092 Ø n 33018 Ø,EP
Grand Cherokee All, Except SRT-8 & Models w/OEM Tow Hook Grand Cherokee Models w/OEM Tow Hook Grand Cherokee All, Except SRT-8 & Models w/OEM Tow Hook Grand Cherokee Models w/OEM Tow Hook Grand Cherokee All, Except Models w/OEM Tow Hook Grand Cherokee Models w/OEM Tow Hook Grand Wagoneer
05-06
n 06378 Ø
3/4”
NO DRILL
20 n 51149 Ø
3/4”
NO DRILL
5
7.5 20
05-06
n 06378 Ø,AI
3/4”
NO DRILL
90 n 51149 Ø,AI
3/4”
NO DRILL
5
07-10
n 06378 Ø
3/4”
NO DRILL
20 n 51149 Ø
3/4”
NO DRILL
07-10
n 06378 Ø,AI
3/4”
NO DRILL
90 n 51149 Ø,AI
3/4”
Liberty
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
3.5 5.5 45
3/4”
n 37042 –
n 88001 –
3/4”, 13/16”, NO DRILL 7/8”
n 51149 Ø n 51085 Ø,GP
n 51010 Ø
Grand Cherokee
n 33002 –
74206
n 37042 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50 18, 19mm
6
7/16", 1/2" 40
15, 18, 21mm, 9/16", 11/16", 3/4", T50 3/4”
n 88001 –
1/4”, 1/2”, 5 9/16”
NO DRILL
15 n 51059 Ø
18, 19mm
NO DRILL
3.5 5 15
n 33018 Ø,EP
18, 19mm, 9/16” 18, 19mm
GC,JM
NO DRILL
5
7.5 75
74889
78104
GC
–
NO DRILL
3.5 5 20 5 7.5 75
74889
78104
GC
85253
n 44092 Ø n 33095 Ø
18, 19mm, 9/16” 18, 19mm
NO DRILL NO DRILL
3/4”
NO DRILL
3.5 5 20 5 7.5 20
78031
78013
BN,CG
85253
7.5 90
n 33095 Ø,AI
3/4”
NO DRILL
5
7.5 90
78031
78013
BN,CG
85253
5
7.5 20
n 33095 Ø
3/4”
NO DRILL
5
7.5 20
74702
78104
BN
85253
NO DRILL
5
7.5 90
n 33095 Ø,AI
3/4”
NO DRILL
5
7.5 90
74702
78104
BN
85253
11-13
n 51195 Ø,GP
21mm
NO DRILL
5
7.5 20
n 44650 Ø,GP
21mm
NO DRILL
5
7.5 20
74702
78104
BN
85219
11-12
n 51195 Ø,AI,GP
21mm
NO DRILL
5
7.5 40
n 44650 Ø,AI,GP
21mm
NO DRILL
5
7.5 40
74702
78104
BN
85219
18, 19mm
NO DRILL
3.5 5 20
18, 19mm
NO DRILL
78013
GC
–
NO DRILL NO DRILL
85750
78104
CH
–
n 44082 Ø,GP
18, 19mm, 9/16” 18, 19mm
3.5 5 3.5 5 4 5
–
18, 19mm
7.5 20
n 33006 Ø n 44093 Ø n 37053 Ø,GP
NO DRILL
5
n 06081 Ø
1993
n 06971 Ø,GP
02-07
18, 19mm 18, 19mm
1/2” NO DRILL
30 n 51010 Ø 15 n 51054 Ø,GP n 37152 –
n 37042 –
n 88001 –
06996
15, 18, 21mm, 9/16", 11/16", 3/4", T50
7/16", 1/2" 35
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
5
18, 19mm
NO DRILL
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 35
45 20 20
7.5 20
85254
HG
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
Commander Compass Compass Compass Rallye Edition Grand Cherokee
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 18mm, 3/4”, 13/16”, 7/8”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
STANDARD WIRE
30 n 37152 –
WRENCHES
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
DRILL BITS
9/16”, 3/4”, 7/8”, NO DRILL various metric
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
T-CONNECTOR
n 06954 Ø,GP
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
97-01 Cherokee Downsize, All Models (Will Not Fit Grand Cherokee)
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
215
JEEP
JEEP
214
REESE TOWPOWER
n 06529 Ø,HM n 06529 Ø,HM
2008 09-12
19mm
NO DRILL
19mm
NO DRILL
2007
n 06428 Ø,GP
16mm, 15/ 16”
5/8”
15 n 51085 Ø,GP
Patriot
08-10
n 06428 Ø,GP
16mm, 15/ 16”
5/8”
15 n 51085 Ø,GP
16mm, 5/8” 15/16” 16mm, 15/16” 5/8”
15
n 44555 Ø,GP
3.5
15
n n n l l l l n
11-12 1997
5/8”
5/8”, 3/4”
NO DRILL
n 06428 Ø,GP 15 n 06021 Ø
16mm, 15/ 16”
n 77016 Ø,DA
5/8”, 3/4”
NO DRILL
15 15 l 51145 Ø,RT,HM
5/8”, 34”
NO DRILL
4
15
TJ Canada
98-06
n 77016 Ø,DA
5/8”, 3/4”
NO DRILL
15 n 06021 Ø
5/8”, 3/4”
NO DRILL
15 l 51145 Ø,RT,HM
5/8”, 34”
NO DRILL
4
15
n 06954 Ø,GP
84-90
9/16”, 3/4”, 7/8” NO DRILL
30 n 51001 –
18mm, 3/4”, NO DRILL 13/16”, 7/8”
3.5 5 40
44555 44661 44661 33036 44565 33036 44565 33002
18, 19mm
NO DRILL
18, 19mm
NO DRILL
5 5
7.5 20 7.5 20
3.5
15
Ø,GP
16mm, 15/16” NO DRILL
Ø,EP,GP,TU
16,22mm
3.5 3.5 3.5 4 4 4 4 3.5 5.5
15 15 15 15 15 15 15 45
3.5 5
40
Ø,EP,GP,TU
16,22mm
NO DRILL
Ø,HM,TD
5/8”, 3/4”
NO DRILL
Ø,HM
5/8”, 3/4”
NO DRILL
Ø,HM,TD
5/8”, 3/4”
NO DRILL
Ø,HM
5/8”, 3/4”
NO DRILL
–
3/4”, 13/16”, NO DRILL 7/8”
n 44088 –
18mm, 7/8”, NO DRILL 13/16”, 3/4”
OEM REPLACE.
FOOTNOTES
STANDARD WIRE
T-CONNECTOR
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. DISTRIB. INSTALL TIME
78017 78017 74682, 85262 74705
78104 78104 78058
–
85219 85219 –
78104
BN,CH
–
85775
78104
BO
–
85775 74489
78104 78058
CH BN
– –
74223
78058
BN
–
–
78013
–
–
BN,CH BN,CH
Wrangler
87-90
n 77003 –
10, 13, 17mm, 9/16”, 5/8”
3/8”
30
–
78058
–
–
Wrangler All, Except Renegade Wrangler All, Inc. Renegade
91-95 91-95
3/8”
30
78058 78058
BN
– –
Wrangler
1997
n 77016 Ø,DA
10, 13, 17mm, 9/16”, 5/8” 5/8”, 3/4”
74489 74489
BN
n 77003 –
NO DRILL
15 n 06021 Ø
74489
78058
BN
–
74223
78058
BN
–
78058 78058 78058 78058
BN
–
– – – –
BN
–
–
– – – – – – – – – – –
Wrangler All, Inc. Unlimited
98-06
n 77016 Ø,DA
5/8”, 3/4”
NO DRILL
15 n 06021 Ø
5/8”, 3/4” 5/8”, 3/4”
NO DRILL NO DRILL
15 l 51145 Ø,RT,HM
98-06 07-12 07-12 87-90
n 77003 –
YJ Canada
91-95
n 77003 –
KIA
Amanti Amanti Forte 4 Dr. Sedan, All Models Magentis Canada Only Magentis Canada Only Optima Optima New Body Style (App. starts with 2006-1/2) Optima Optima, All, Incl. LX & EX Rio All, Inc. Cinco Rio 4 Dr. Sedan Rio 4 Dr. Sedan EX Rio 4 Dr. Sedan LX Rio 4 Dr. Sedan SX Rio 5 Dr. Hatchback Only Rio 5 Dr. Hatchback Only Rondo Sedona Sedona 118.9 Long Wheelbase Only Sedona 113.8 Short Wheelbase Only Sorento Sorento Sorento, Base I4 Sorento, EX I4 Sorento, EX V6 w/ Factory Tow Package
04-06 07-09 10-13 01-04 06-10 01-06 06-08 09-10 11-13 02-05 06-11 2012 2012 2012 06-11 12-13 07-10 02-05 06-12 07-10 03-06 07-09 11-13 11-13 11-13
n 77154 Ø,HM,JR n n n n n n n n n n n
77154 77154 77225 77044 77136 77272 77272 77272 77167 77270 77169
17mm, 11/16” 17mm, 3/4”
5/8”, 34”
NO DRILL
4
3/4”
NO DRILL
3/4”
NO DRILL
3.5 4 20 3.5 4 20
l l l l
33036 44565 33036 44565
Ø,HM,TD
5/8”, 3/4”
NO DRILL
Ø,HM
5/8”, 3/4”
NO DRILL
Ø,HM,TD
5/8”, 3/4”
NO DRILL
Ø,HM
5/8”, 3/4”
NO DRILL
3/4”
NO DRILL
3/4”
NO DRILL
4 4 4 4
15 15 15 15
3.5 4 3.5 4
20 20
15
30
3/8”
30
74489
78058
– 78011 74692 – – – 78065 74710 78011 – –
78013 78013 78013 78013 78013 78013 78013 78013 78013 78013 78013
–
78013
NO DRILL
NO DRILL
3/4”
NO DRILL
NO DRILL
Ø,HM,JR
17mm, 3/4”
NO DRILL
Ø,HM,JR
17mm, 3/4”
NO DRILL
Ø,HM,JR,KH
10, 13mm, 11/16” NO DRILL
TA
3/4”
1/2”
Ø
19mm
NO DRILL
Ø,HM
11/16”
NO DRILL
Ø,HM
11/16”
NO DRILL
Ø,HM
11/16”
NO DRILL NO DRILL
Ø,JR,X
17, 19mm
Ø,GP,JR,SV
10mm, 11/16”, 3/4” NO DRILL
Ø,GP,JR
10, 12, 13, 14, 17mm NO DRILL
20 n 51077 Ø 20 n 51077 Ø
n 44557 Ø n 44557 Ø
40 20
20 20 20 20 30 20 20 15 15 15 25 30 30
BN BN
– CG – – – CG CG HG – –
– B,LD
n 06029 –
06996
15
3/8”
3/4”
n 06396 Ø,HM,JR,SC 10, 12, 13, 17mm NO DRILL n 06607 Ø,HM,JR 10, 12, 17mm, 11/16” NO DRILL n 77234 Ø,HM,JR
4
74223 74693 74693 –
l 06448 Ø l 06448 Ø 10, 13, 17mm, 9/16”, 5/8” 10, 13, 17mm, 9/16”, 5/8”
NO DRILL
15 l 51145 Ø,RT,HM
Wrangler Except Unlimited Wrangler Unlimited, 4 Dr. Wrangler YJ Canada
5/8”, 34”
17, 18mm, 7/8”
1/2”
20
l l 16mm NO DRILL 15 n n 06133 Ø,HM 16mm NO DRILL 15 n n 06133 Ø,HM 16mm NO DRILL 15 n n 06133 Ø,HM Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
51082 51082 51206 51206 51206
Ø,RT,HM
19mm
NO DRILL
Ø,RT,HM
19mm
NO DRILL
Ø, HM
16mm
NO DRILL
Ø, HM
16mm
NO DRILL
Ø, HM
16mm
NO DRILL
5 5 3.5 3.5 3.5
5 5 5 5 5
15 15 15 15 15
n n n l l n n n
33062 44537 44578 44558 44558 44639 44639 44639
–
17, 18mm, 7/8” 1/2”
Ø,JR
19mm
HM,JR
12, 17mm, 3/4” 3/8”
NO DRILL
Ø,HM
19mm
NO DRILL
Ø,HM
19mm
NO DRILL
Ø,HM
16mm
NO DRILL
Ø,HM
16mm
NO DRILL
Ø,HM
16mm
NO DRILL
5 3.5 3.5 5 5 3.5 3.5 3.5
5.5 4 4 5 5 5 5 5
30 20 25 15 15 15 15 15
74708 85266 78046 78046 85317 74706 85726 85726 85760
78013 78013 78104 78104 78013 78104 – – –
– HG BN,CH BN,CH BN,HG – CH CH BN,CH
– – – – – – – – – – –
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
217
APPLICATIONS GUIDE
16mm, 15/16” NO DRILL
NO DRILL
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
3.5
Patriot TJ Canada
Wagoneer Downsize, All Models (Will Not Fit Grand Wagoneer)
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
l 44585 Ø,HM l 44585 Ø,HM
15 15
Patriot
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
Liberty Liberty
APPLICATIONS GUIDE
REESE TOWPOWER
JEEP - KIA
JEEP - KIA
216
REESE TOWPOWER
LEXUS
NO DRILL NO DRILL
16mm
NO DRILL
16mm
NO DRILL
Ø, HM
16mm
NO DRILL
Ø, HM
16mm
NO DRILL
02-03
10mm, 19mm
NO DRILL
14, 17mm
NO DRILL
14, 17mm
NO DRILL
04-06
03-09
HS 250h Hybrid LX 450 LX 470 LX 470 LX 470 LX 470 RX 300 RX 300 RX 330 All, Inc. Models w/18 Spare Tire RX 350 RX 350
10-11 96-97 98-99 2000 01-02 03-07 99-00 01-03 04-06 07-09 10-13
06264 06264 06339 51180 06339 51180 06994 06132
HM
17mm, 3/4”
1/2”
HM
17mm, 3/4”
1/2”
Ø,GP.JR
13, 14, 17mm
NO DRILL
Ø,GP.JR
13, 14, 17mm
NO DRILL
Ø,GP.JR
13, 14, 17mm
NO DRILL
Ø,GP.JR
13, 14, 17mm
NO DRILL
Ø,GP, †
16mm
NO DRILL
Ø,GP.JR
16mm
NO DRILL
20 20 25 25 25 25 15 20
n 44666 O,GP,JR
16mm
3.5 5.2 20
85751
78104
B,E
–
n 33064 – n 33064 – n 44640 Ø,HM
3.5 3.5 4 4
– – –
78104 78104 78104
–
13, 17mm, 3/4” 1/2”
–
– – –
40 30 30 n n n n n n
– – – –
78104 78104 78104 78104
–
– – – –
06326 51178 06326 51178 06326 51178
HM
14, 17mm, 11/16” 1/2”
HM
14, 17mm, 11/16” 1/2”
HM
14, 17mm, 11/16” 1/2”
HM
14, 17mm, 11/16” 1/2”
–
78104
–
–
HM
14, 17mm, 11/16” 1/2”
HM
14, 17mm, 11/16” 1/2”
–
78104
–
–
85740 74682 –
– 85262 78104
– BO
– – –
85728 74208 74225 – – – – – 78106 78106 78106
– 78013 78013 78104 78104 78104 78104 78104 78104 78104 78104
–
– 85708
78104 78104
–
l 44548 Ø,LT,SI NO DRILL
14, 17mm
NO DRILL
14, 17mm
NO DRILL
15 l 51153 15 l 51153 l 51155 l 51155
Ø,HM
14, 17mm
NO DRILL
Ø,HM
14, 17mm
NO DRILL
Ø,RT
14, 17mm
NO DRILL
Ø,RT
14, 17mm
NO DRILL
l 51155 Ø,RT
06996
22mm, NO DRILL 11/16”, 5/8”
20 20 20
19mm
NO DRILL
5
5
15
10, 12, 13, NO DRILL 17mm, 3/4”, 1/2”
6
7.3 35
17, 18mm
5 5 5 5 5 3.5 3.5 3.5 3.5 4
6 6 6 6 6
5
30 20 20 20 20 15 15 20 20 30
4
5
30
3.5 4 5
20 30
25
n 06276 Ø n 06276 Ø
06-09 10-12
13, 17mm, 3/4” 1/2”
15 15 15 15 15 15 n 44644 Ø
n 77237 Ø,HM,JR,KH 10, 17, 19mm
NO DRILL
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
14, 17mm
NO DRILL
3.5 3.5 3.5 3.5
3.5
15 15 20 20
20
n n n n n l l l l n
33066 44546 44546 44546 44546 44076 44076 33075 33075 44633
Ø
NO DRILL
Ø
12, 19mm, 7/8” NO DRILL
Ø
12, 19mm, 7/8” NO DRILL
Ø
12, 19mm, 7/8” NO DRILL
Ø
12, 19mm, 7/8” NO DRILL
Ø,HM
14, 17mm
NO DRILL
Ø,HM
14, 17mm
NO DRILL
Ø
14, 17mm
NO DRILL
Ø
14, 17mm
NO DRILL
Ø,GP,JR,JV
10, 12, 14, 17, NO DRILL 19mm n 44627 Ø,†,GP,JR,JV 10, 12, 14, 17, NO DRILL 19mm 14, 17mm NO DRILL l 33075 Ø n 44633 Ø,GP,JR,JV 10, 12, 14, 17, NO DRILL 19mm
OEM REPLACE. –
FOOTNOTES BN,CG
WT. DISTRIB. INSTALL TIME
78013
NO DRILL NO DRILL
15 15 15 15
WT. CARRYING
78038
16mm 16mm
5 5 5 5
DRILL BITS
25
Ø,HM Ø,HM
3.5 3.5 3.5 3.5
WRENCHES
3.5
NO DRILL NO DRILL
FOOTNOTES
13, 14, 17mm NO DRILL
16mm 16mm
HITCH NUMBER
n 44582 Ø,GP.JR
Ø,HM Ø,HM
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE 25
DRILL BITS
3.5
44639 44639 44639 44639
15 15 15 15
10-12
GX 470
13, 14, 17mm NO DRILL
– – – – – 78013 78104 78104 –
n n n n
5 5 5 5
40 20 n n n n n n n n
l 77102 EP n 77004 Ø n 77004 Ø
n 44582 Ø,GP.JR
85726 85726 85726 85760 74708 – – 74895 –
3.5 3.5 3.5 3.5
WRENCHES
DRILL BITS
WRENCHES
FOOTNOTES Ø, HM Ø, HM
HITCH NUMBER
16mm 16mm
51206 51206 51206 51206
n n n n
STYLE
Ø,HM Ø,HM
15 15 15 15
WT. CARRYING WT. DISTRIB. INSTALL TIME
NO DRILL NO DRILL
HITCH NUMBER
16mm 16mm
INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
HITCH NUMBER
Ø,HM Ø,HM
02-03 04-05 08-12
ES 300 4 Dr.
RX 400h Hybrid RX 450h Hybrid
NO DRILL NO DRILL
11-13
90-91 90-91 92-96 97-01
GX 460
17mm 14, 17mm, 7/8”
05-10
250 250 FWD 300 4 Dr. 300 4 Dr.
ES 330 4 Dr.
n 77230 Ø,GP,JR n 77099 Ø,JR
06133 06133 06133 06133
STANDARD WIRE
ES ES ES ES
n n n n
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
–
– – – – – – – – –
CH CH CH BN,CH BN,CG – – HG
–
– – –
– CH BN,HG BN,HG – – – – – – –
–
– – – – – – – – – – –
– –
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
219
APPLICATIONS GUIDE
LAND ROVER
Freelander Freelander LR2
11-13 11-13 11-13 11-13 10-13 05-09 95-97 98-02 05-10
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
T-CONNECTOR
Sportage
YEAR
MODEL
Sorento, EX V6 w/o Factory Tow Package Sorento, LX I4 Sorento, LX V6 Sorento SX V6 Soul Spectra Except Spectra5 Sportage 2 & 4 Dr. Sportage 2 & 4 Dr. Sportage 4 Cyl. Models
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
FOOTNOTES
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
Sportage 6 Cyl. Models
APPLICATIONS GUIDE
REESE TOWPOWER
KIA - LEXUS
KIA - LEXUS
218
REESE TOWPOWER
REESE TOWPOWER
Continental
98-02
n 77017 Ø,JR n 77017 Ø,JR
10, 13, 15mm, 3/4” NO DRILL 10, 13, 15mm, 3/4” NO DRILL
20 n n 20 n n n n
06368 88002 06368 88002 06393 06393
10, 13, 15mm, 3/4” NO DRILL 3/4”
1/2”
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
–
3/4”
1/2”
–
11/16”
7/16”
FE
11/16”
7/16”
Mark VIII
93-98
25 n 06043 CA n 88002 – n 06004 Ø,JR
MKS
09-13
n 06663 Ø,JR
MKT All Models
10-13
MKX
07-10
MKX
11-13
MKZ MKZ Navigator
07-09 10-12 98-02
80-89 90-02
3/4”
1/2”
n 06525 Ø,GP,JR,KH
n 77152 GP,JR,TA n 77239 Ø
12, 13mm, 3/4”
1/2”
11/16”
NO DRILL
13mm, 3/4”
1/2”
3/4”
1/2”
13mm, 11/16”, NO DRILL 3/4”, 7/8” 10, 13, 18, 19mm, NO DRILL 11/16”, 3/4”
5.5, 8mm, 3/4”
NO DRILL
n 77002 CA,HA
3/4” 3/4”
1/2” 1/2”
5
8 8
–
–
85251 85251 74682
– – 78058
LS LS BO
– – 85219
–
–
–
85727 –
– 78058
CH, BO –
85219 –
–
78104
–
–
78095
78104
CH
–
30
85727
78104
CH
–
CH, BO
20
7/16”
5
10 30
21mm, 3/4”, NO DRILL 7/8”
6
13/16”, 7/8” NO DRILL
5 8 20 3.5 6 30
13mm, 3/4” 1/2”
10 20
l l l l n
33077 37090 44131 44655 44552
Ø,HM
3/4”
7/16”
Ø
3/4”
7/16”
Ø
3/4”
7/16”
HM
3/4”
7/16”
Ø,CP
21mm, 3/4”, NO DRILL 7/8”
n 33047 CA,GP
13mm, 3/4”
1/2”
6 6 5 6 6
8 10 10 8 10
3.5 6
30 30 30 30 20 n 41933 Ø,@,CP,HM, 3/4”, 7/8” † n 96933 Ø,@,CP,HM 3/4”, 7/8”
30
30
06043 88002 06043 88002 06043 06043 88002
CA
13mm, 3/4”
1/2”
45
85727 85774
– 78104
CH
85219 –
3.5 4
45
85746
78104
CH
–
85731 85766 74665 74665
78104 78104 78058 78058
CH
BN, BO
– – – 85219
n 51200 CP,GP,JR,KH 5.5, 8mm, 3/4” 1/2”
4
0
55
n 44658 Ø,GP,JR,KH 5.5mm or 7/32”, NO DRILL
–
3/4”
1/2”
CA,HA
13mm, 3/4”
1/2”
–
3/4”
1/2”
30 35 30 35 30 30 35
n 51103 AB,CA,GP
13mm, 3/4” 1/2”
12 20
3.5
n 44567 Ø, CP, GP, JR, KH
8mm, 3/4”
4
45 20
25 n n 25 n n n 25 n n 45
10
5.5, 8mm, 3/4” NO DRILL
55
3/4”, 7/8”
n 44032 Ø,HM
7/8”, 3/4”
3.5 6 30
n 44622 Ø,GP n 33047 AB,CA,GP
n 51103 AB,CA,EO,GP,HA 13mm, 3/4” 1/2”
3.5 6 30
n 51103 AB,CA,EO,GP,HA 13mm, 3/4” 1/2” n 51103 AB,CA,GP 13mm, 3/4” 1/2”
3.5 6 30 3.5 6 30
10 15
NO DRILL
4
0
5
12 20 –
18, 19mm, 6” NO DRILL ratchet
4
21mm, 3/4”, NO DRILL 7/8”
10
85219
models w/ Tow 85219 Package only BO 85219
l 44636 Ø,HM,JR 45 n 51200 CP,GP,JR,KH 5.5, 8mm, 3/4” 1/2”
n 51024 Ø,HM
NO DRILL
BO
OEM REPLACE.
78104
20
FOOTNOTES
–
WT. DISTRIB. INSTALL TIME
78104
WT. CARRYING
–
models w/ Tow 85219 Package only – –
DRILL BITS
78058 78058
WRENCHES
– 74682
FOOTNOTES
78058 78058
HITCH NUMBER
74665 74682
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
n 51096 Ø,CP,HM 30 n 51103 CA,GP 35 40
3/4”
n 33052 Ø,GP
n 77002 CA
15, 18mm, 7/8” NO DRILL
5
NO DRILL
5
8
20
CH BN
NO DRILL
5
10 20
7/8”, 3/4”
NO DRILL
13mm, 3/4”
1/2”
6 10 15 3.5 6 30
–
78104
–
–
n 33047 AB,CA,EO,GP,HA 13mm, 3/4” 1/2”
3.5 6
30
–
78104
–
–
n 33047 AB,CA,EO,GP,HA 13mm, 3/4” 1/2” n 33047 AB,CA,GP 13mm, 3/4” 1/2”
3.5 6 3.5 6
30 30
– –
78104 78104
– –
– –
–
78104
–
–
CH
Town Car Town Coupe
03-10 80-89
n 77002 CA,HA
3/4”
1/2”
Zephyr
2006
n 77152 GP,JR,TA
12, 13mm, 3/4”
1/2”
2 3 4 Dr. Sedan, Except Models with Grand Touring LED Taillights Package 3 5 Dr. Hatchback, Except Models with Grand Touring LED Taillights Package 3 4 Dr. Sedan, Models with Grand Touring LED Taillights Package 3 5 Dr. Hatchback, Models with Grand Touring LED Taillights Package 3 4 Dr. Sedan, Except Models with Grand Touring LED Taillights Package
11-13 04-09
77252 Ø,GP,JR n 77188 GP
10mm, 7/16"11/16" NO DRILL 11/16”
1/2”
30 35
85754 74697
78104 78013
CG
– –
04-09
n 77188 GP
11/16”
1/2”
35
74697
78013
CG
–
06-09
n 77188 GP
11/16”
1/2”
35
–
78013
–
–
06-09
n 77188 GP
11/16”
1/2”
35
–
78013
–
–
10-12
n 77244 Ø,GP
10mm, 11/16”, 9/16”
NO DRILL
20
74697
78013
CG
–
MAZDA
06996
CA,HA
13mm, 3/4”
1/2”
CA
13mm, 3/4”
1/2”
–
3/4”
1/2”
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
n 51075 Ø,CP
06-08
n 77002 CA
15, 18mm, 7/8” NO DRILL
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
20 40 20 40 20 30 l 51064 Ø,RT
80-83
Town Car
DRILL BITS
Ø,GP,JR –
Mark VI, All Styles
Town Car
WRENCHES
FOOTNOTES
HITCH NUMBER
l 33031 Ø,KL
2005
00-02 LS 03-06 LS Mark LT Built Before 8/2005 w/ Factory 7-Way 2006
Mark LT Built After 8/2005
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
l 33031 Ø,KL
03-04
88-97
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
STANDARD WIRE
Aviator
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
T-CONNECTOR
Aviator
YEAR
MODEL LINCOLN
Continental
APPLICATIONS GUIDE
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
221
LINCOLN - MAZDA
LINCOLN - MAZDA
220
REESE TOWPOWER
REESE TOWPOWER
CX-5 CX-7
2013 07-12
CX-9 Millenia MPV Van MPV Van MPV Van MPV Van Navajo
2 & 4 WD w/Ground Effects w/o Ground Effects All Models
Pickup B-Series All Models
OEM REPLACE.
FOOTNOTES
STANDARD WIRE
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
10mm, 11/16”, 9/16”
NO DRILL
20
–
78013
–
–
10-12
n 77245 Ø,GP
11/16”, 9/16”
NO DRILL
15
74697
78013
CG
–
10-12
n 77245 Ø,GP
11/16”, 9/16”
NO DRILL
15
–
78013
–
–
06-10 2012 03-08 04-07 04-08 09-13 98-02
n n n n n n n
85754 85754 85701 – 85701 78112 –
78104 78104 78104 78104 78104 78104 78013
CH
– – – – – – –
85701 78061 85754 – – – – – 74190
78104 78104 78104 78104 78104 78104 78104 78104 78058
BN
– 78061 – – – – – – –
–
78013
–
–
78013
BN,HG
–
77150 77246 77152 77159 77152 77205 77021
GP GP GP,JR,TA Ø,TA GP,JR,TA GP,JR JR
25 25 12, 13mm, 3/4” 1/2” 45 11/16” NO DRILL 25 12, 13mm, 3/4” 1/2” 45 11/16” 1-1/8” hole saw 30 3/4”, 7/8” 1/2”, 1” hole 30 11/16”, 3/4”
1/2”
11/16”, 3/4”
3/8”
saw
n 06401 Ø,GP,JR
11/16”
NO DRILL
n 44677 Ø,GP,JR l 44554 Ø,GP,JR
40
l 44572 Ø,HM
07-12 95-02 96-98 00-03 00-03 04-06 91-94
n 06134 AI
n 06068 Ø,JR n 06365 –
10mm, 11/16”
7/16”
17mm, 3/4”, 7/8” NO DRILL 13/16”, 7/8”, 15/16”
1/2”
n 44617 – n 44553 Ø,HM,JR
7/8”
n 51092 Ø,RT,HM,JR 17mm, 3/4”, 7/8” NO DRILL 3/4”, 13/16” 1/2” 15 l 37051 –
3.5 5 20 5 6 25
n 44553 Ø,HM,JR l 33051 –
17mm, 7/8”, 3/4” NO DRILL
n 37041 –
3/4”, 13/16” 1/2”
5
6
25
l 44067 –
n 51033 –
15, 18, 21mm, 3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
5
6 20
n 44100 –
NO DRILL
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 30
18,19mm, 3/4”, 7/8” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/2”
3.5 5 20
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 40
n 33058 EG,SD n 44101 EG
1/2”, 3/8”
17mm, 7/8”, 3/4” NO DRILL
3.5 5 3.5 5
50 20
3.5 5 5 6
20 20
13/16”, 7/8”, 1/2” 15/16” 13/16”, 1/2” 7/8”,15/16” 15, 18, 21mm, NO DRILL 3/4”, 15/16”
5
6
45
5
6
20
18, 19mm, 7/8” 18,19mm, 3/4”, 7/8”
1/2”
4
6
20
1/2”
3.5 5
20
n 37152 Ø
98-01
74424
74424 18,19mm, 3/4”, 7/8”
1/2”
3.5 5 20
n 33058 SD,V n 44101 V
n 37042 Ø
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 40
18, 19mm, 7/8” 18,19mm, 3/4”, 7/8”
1/2”
4
6
20
1/2”
3.5 5
20
7/16", 1/2" 35
CH – CH CH –
CH BO CH – – – – –
HG
74424
78013
BN,HG
74885
74424
78013
BN,HG
74885
74424 n 51032 V
18,19mm, 3/4”, 7/8”
1/2”
3.5 5 20
n 33058 SD,V n 44101 V
06996
15
–
74672
n 51032 V
99-01
4
7/16", 1/2" 35
1998
15, 18, 21mm, 9/16", 11/16", 3/4", T50
4
40 40
7/16", 1/2" 30
n 51032 EG
n 88001 –
3.5 3.5
15
94-97
15, 18, 21mm, 9/16", 11/16", 3/4", T50
NO DRILL
3.5 5 20
n 37152 –
n 88001 –
19mm
NO DRILL
n 51092 Ø,RT,HM,JR 17mm, 3/4”, 7/8” NO DRILL
90-93
15, 18, 21mm, 9/16", 11/16", 3/4", T50
11/16”, 3/4” NO DRILL 11/16”
60
n 37042 Ø
Pickup B-Series All Models
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
n 77244 Ø,GP
n 37152 Ø
Pickup B-Series All Models
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
10-12
n 88001 –
Pickup B-Series All Models
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
n 37042 –
Pickup B-Series All Models
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
18, 19mm, 7/8” 18,19mm, 3/4”, 7/8”
1/2”
4
6
20
1/2”
3.5 5
20
74424
HG
78013
BN,HG
74885
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
3 4 Dr. Sedan, Models with Grand Touring LED Taillights Package 3 5 Dr. Hatchback, Except Models with Grand Touring LED Taillights Package 3 5 Dr. Hatchback, Models with Grand Touring LED Taillights Package 5 5 6 4 Dr. Sedan 6 Sport Wagon 6 5 Dr. Hatchback 6 4 Dr. Sedan 626
STYLE
YEAR
MODEL
APPLICATIONS GUIDE
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
223
MAZDA
MAZDA
222
REESE TOWPOWER
REESE TOWPOWER
n 37152 Ø
n 37042 Ø
n 88001 – 95-98 99-03 02-03 01-02
n 77241 †,JR n 77080 Ø n 77119 Ø,JR
3/4” 7/8”
1/2”
3/4”, 7/8”, 11/16”
NO DRILL
14mm, 11/16”
NO DRILL
l 51142 Ø,RT,KH
15, 18, 21mm, 9/16", 11/16", 3/4", T50
l 51142 Ø,RT
n 37042 –
n 88001 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
6.5 40
3.5 5
20
n 37152 –
n 37042 –
n 88001 –
10, 18mm, 11/16” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
NO DRILL
3.5 5 35
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 60
l 33039 Ø,KH
10, 18mm, 11/16” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
NO DRILL
3.5 5 35
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 60
l 33039 Ø
10, 18mm, 11/16” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
NO DRILL
3.5 5 35
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 60
l 33039 Ø
1”, 3/8”
20
l 44647 Ø
n 06417 HM
7/8”
1”, 3/8”
20
l 44680 Ø.HM
n 51191 †,HM n 51194 HM
7/8”
1”, 3/8”
7/8”
1”, 3/8”
20 20 l 97207 Ø, † l 97232 Ø,HM
1”, 3/8”
10, 18mm, 5/8” NO DRILL 10, 18, 22mm, NO DRILL 5/8”
3.5 5 3.5 5
NO DRILL
3.5 5
40
10, 18mm, 11/16”
NO DRILL
3.5 5
40
10, 18mm, 11/16”
NO DRILL
3.5 5
40
7/8”
1”, 3/8”
7/8”
1”, 3/8”
7/8”
1”, 3/8”
– – – 74664
74664
–
BN,HG
OEM REPLACE.
FOOTNOTES
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
78013
–
HG
78013 78013 – 78013
– – – HG,RW
– – – –
HG,RW
78013
HG,RW
–
HG,RW
78013
–
20 20 20
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
10, 18mm, 5/8” NO DRILL 10, 18, NO DRILL 22mm, 5/8”
3.5 5 3.5 5
3.5 5
25
74703
78104
BN, CH
3.5 5.25 25
74702
–
BN,CH
74703 l 44647 Ø
20
l 97207 Ø, † l 97232 Ø,HM
10, 18mm, NO DRILL 5/8” 10, 18, 22mm, NO DRILL 5/8”
25 25
l 44680 Ø.HM n 06417 HM n 51191 †,HM n 51194 HM
74424
–
74672
n 06417 †,HM
7/8”
10, 18mm, 11/16”
7/16", 1/2" 60
15, 18, 21mm, 9/16", 11/16", 3/4", T50 7/8”
n 06417 †,HM
STANDARD WIRE
1/2”
T-CONNECTOR
20
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
6
74664 l 51142 Ø,RT
06996
WRENCHES
STYLE
FOOTNOTES
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
1/4”, 1/2”, 5 9/16”
4
7/16", 1/2" 60
2004
08-11
6
1/2”
74664
n 37152 –
Tribute All, Inc. Hybrid
n 44101 V
1/4”, 1/2”, 5 9/16”
18, 19mm, 7/8” 18,19mm, 3/4”, 7/8”
7/16", 1/2" 60
2003
05-06
n 33058 SD,V
40 20 15
n 88001 KH
Tribute
3.5 5 20
74424
n 37042 KH
Tribute
1/2”
7/16", 1/2" 35
n 37152 KH
Tribute
18,19mm, 3/4”, 7/8” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
25 25
10, 18mm, NO DRILL 5/8” 10, 18, 22mm, NO DRILL 5/8”
3.5 5
–
BN,CH
25
85774
78058
CH
78070
3.5 5.25 25
85774
–
CH
–
78070
78058
BO
–
85774 85774
–
CH
CH
–
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
Protege All Models Protege All Models Protege 5 Tribute
15, 18, 21mm, 9/16", 11/16", 3/4", T50
WRENCHES
FOOTNOTES
HITCH NUMBER
n 51032 V
02-09
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Pickup B-Series All Models
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
225
MAZDA
MAZDA
224
REESE TOWPOWER
10-13 98-02
l 44649 Ø,HM n 33027 Ø
ML320 CDI ML350
07-08 03-05
l 44534 MB,TA n 33027 Ø
ML350 ML350 Except Blue Tec ML350, All Styles ML430
06-09 10-11 12-13 99-01
l l n n
ML450 Hybrid, All Styles ML500
10-11 02-05
l 44534 MB,TA n 33027 Ø
ML500 ML550 R320 BlueTEC R320 BlueTEC w/Panoramic Roof Package R320 CDI R320 CDI w/Panoramic Roof Package R350 R350 w/Panoramic Roof Package R500 R500 w/Panoramic Roof Package Sprinter 144 & 170 Wheelbase Models Only, Except w/Factory Step Bumper
06-07 08-11 2009 2009
l l n n
44534 44534 44547 44547
07-08 07-08 06-12 06-12 06-07 06-07 10-12
n n n n n n n
44547 44547 44547 44547 44547 44547 44576
MERCURY
79-86
l 77060 X
Colony Park Wagon
83-91
n 77002 CA
9/16”, 5/8”, 11/16 In 3/4”
3/8”
20
1/2”
Cougar All Models
89-95
25 n 06043 CA n 88002 – n 06004 Ø
Cougar All Models
96-97
n 06004 Ø
Grand Marquis
83-91
Grand Marquis Grand Marquis Grand Marquis Wagon Marauder Mariner All, Inc. Hybrid
92-97 98-11 83-91 03-04 05-07
n 77002 CA n 77002 CA n 77002 CA n 77002 CA n 77002 CA
3/4” 3/4” 3/4” 3/4” 3/4”
1/2” 1/2” 1/2” 1/2” 1/2”
25 n n 25 n n 25 n n 25 n n 25 n n
06043 88002 06043 88002 06043 88002 06043 88002 06043 06417
06996
MB,TA
10mm, 16mm, 3/4” NO DRILL
Ø,GP,JR
10mm, 11/16”
Ø
10, 21mm, 3/4”, NO DRILL 11/16”, 9/16” 10mm, 16mm, 3/4” NO DRILL
NO DRILL
MB,TA
10, 21mm, 3/4”, NO DRILL 11/16”, 9/16” 10mm, 16mm, 3/4” NO DRILL
MB,TA
10mm, 16mm, 3/4” NO DRILL
Ø,SC
10, 15, 17mm NO DRILL
SC
10, 15, 17mm NO DRILL
Ø,SC
10, 15, 17mm NO DRILL
SC
10, 15, 17mm NO DRILL
Ø,SC
10, 15, 17mm NO DRILL
SC
10, 15, 17mm NO DRILL
Ø,SC
10, 15, 17mm NO DRILL
SC
10, 15, 17mm NO DRILL
Ø,HM
18, 19mm
NO DRILL
OEM REPLACE.
FOOTNOTES
STANDARD WIRE
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
MB,TA
10, 21mm, 3/4”, NO DRILL 11/16”, 9/16” 10mm, 16mm, 3/4” NO DRILL
4 5
5
20 30
– –
78113 78113
–
3.5 4 5 5
50 30
– –
78113 78113
–
3.5 3.5 3.5 5
4 4 4 5
50 50 30 30
– –
78113 78113
–
– –
–
78113
–
–
3.5 4 5 5
50 30
– –
78113 78113
– –
– –
3.5 4 3.5 4 3.5 3.5
50 50 25 50
– – – –
78113 78113 78113 78113
3.5 3.5 3.5 3.5 3.5 3.5 6 7.5
25 50 25 50 25 50 20
– – – – – –
78113 78113 78113 78113 78113 78113
–
– – – – – –
–
78104
–
–
–
–
–
– – – – – – – – –
– – – –
– – – –
78058
–
–
NO DRILL
–
78058
–
–
NO DRILL
40
–
78058
–
–
1/2”
CA
13mm, 11/16”, 3/4”, 7/8” 13mm, 11/16”, 3/4”, 7/8” 13mm, 3/4”
–
3/4”
1/2”
CA
13mm, 3/4”
1/2”
†,HM
7/8”
1”, 3/8”
30 35 30 35 30 35 30 35 30 20
n 06417 HM
7/8”
1”, 3/8”
20
n 51191 †,HM n 51194 HM
7/8”
1”, 3/8”
7/8”
1”, 3/8”
20 20
CA
13mm, 3/4”
1/2”
–
3/4”
1/2”
CA
13mm, 3/4”
1/2”
–
3/4”
1/2”
CA
13mm, 3/4”
1/2”
–
3/4”
1/2”
n 06417 †,HM n 51191 †,HM
NO DRILL
10, 21mm, 3/4”, NO DRILL 11/16”, 9/16” 10mm, 16mm, 3/4” NO DRILL
–
1/2” 1/2”
n 51103 CA,GP
13mm, 3/4” 1/2”
3.5 6 30
n 33047 CA,GP
13mm, 3/4”
1/2”
3.5 6
30
–
78058
–
–
n 51103 CA,GP
13mm, 3/4” 1/2”
3.5 6 30
n 33047 CA,GP
13mm, 3/4”
1/2”
3.5 6
30
74428
78104
–
–
n 51103 CA,GP
13mm, 3/4” 1/2”
3.5 6 30
n 33047 CA,GP
13mm, 3/4”
1/2”
3.5 6
30
–
78104
–
–
–
78058
–
–
– –
78104 78104
– CH
– –
85774
–
CH
–
n 51103 CA,GP
7/8”
1”, 3/8”
7/8”
1”, 3/8”
13mm, 3/4” 1/2”
3.5 6 30
n 33047 CA,GP l 44647 Ø l 44680 Ø.HM
l 97232 Ø,HM 08-09
7/8”, 3/4”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
30 35 40
13mm, 3/4” 3/4”
l 97207 Ø, †
Mariner All, Inc. Hybrid
44534 44534 44678 33027
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
GLK350 All Models ML320
Capri
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL MERCEDESBENZ
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
20 20
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
10, 18mm, NO DRILL 5/8” 10, 18, NO DRILL 22mm, 5/8”
13mm, 3/4”
1/2”
10, 18mm, NO DRILL 5/8” 10, 18, 22mm, NO DRILL 5/8”
3.5 6 3.5 5
30 25
3.5 5.25 25
3.5 5
25
85774
3.5 5
25
85774
–
85774 78070
78058 78058
CH CH
–
CH
78070
Factory Tow – Package models only
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
227
APPLICATIONS GUIDE
APPLICATIONS GUIDE
REESE TOWPOWER
MERCEDES-BENZ - MERCURY
MERCEDES-BENZ - MERCURY
226
REESE TOWPOWER
REESE TOWPOWER
l 44647 Ø
20
l 44680 Ø.HM n 51194 HM
7/8”
1”, 3/8”
n n n n
77002 77002 77152 77239
Monterey Sedan Monterey Van Mountaineer
79-82 04-07 97-01
n 77002 CA
CA
3/4”
1/2”
CA
3/4”
1/2”
GP,JR,TA
12, 13mm, 3/4”
1/2”
Ø,GP,JR
11/16”
NO DRILL
3/4”
1/2”
25 n 06043 CA 25 n 06043 CA 45 20 n 06301 Ø,GP,JR n 25 n n n
51179 06043 06989 06365
13mm, 3/4”
1/2”
13mm, 3/4”
1/2”
30 n 51103 CA,GP 30
10, 13, 15mm, 3/4” NO DRILL
30 30 30 n 51103 CA,GP 25 15 l 37051 Ø,JF
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
CA
13mm, 3/4”
1/2”
Ø,JR
7/8”
NO DRILL
Ø
13/16”, 7/8”, 15/16”
1/2”
n 37041 Ø,JF n 51033 Ø
10, 18mm, NO DRILL 5/8” 10, 18, NO DRILL 22mm, 5/8” 13mm, 3/4” 1/2”
13mm, 3/4” 1/2”
3.5 5
25
Sable Sedan, All Models Sable Sedan, All Models Sable Sedan, All Models
Sable Sedan, All Models Sable Sedan, All Models
Sable Wagon Sable Wagon Sable Wagon Sable Wagon
Sable Wagon
02-03 04-05 06-07 08-10 95-00 86-91 92-95 96-99 00-03
n 77009 – n 77017 Ø,JR,KH n 77017 Ø,JR n 77017 Ø,JR n 77017 Ø,JR
13mm, 3/4”
1/2”
10, 13, 15mm, 3/4” NO DRILL 10, 13, 15mm, 3/4” NO DRILL 10, 13, 15mm, 3/4” NO DRILL 10, 13, 15mm, 3/4” NO DRILL
04-05 08-09
86-91 92-95 96-99 00-03
n 77017 Ø,JR,KH n 77017 Ø,JR n 77017 Ø,JR n 77017 Ø,JR
10, 13, 15mm, 3/4” NO DRILL 10, 13, 15mm, 3/4” NO DRILL 10, 13, 15mm, 3/4” NO DRILL 10, 13, 15mm, 3/4” NO DRILL
30 20 n n 20 n n 20 n n 20 n n n n n n
06368 88002 06368 88002 06368 88002 06368 06991 51101 06991 51101 06991
n n n n n n n n n n n n n
06301 51179 06368 88002 06368 88002 06368 88002 06368 06991 51101 06991 51101
20 20 20 20
04-05
Tracer All Models
91-96
n 77018 –
Tracer Sedan
1997
n 77018 – 06996
9/16”, 11/16”, 13/16” 9/16”, 11/16”, 13/16”
Ø,GP,JR,KH
10, 13, 15mm, 3/4” NO DRILL
–
3/4”
1/2”
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
–
3/4”
1/2”
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
–
3/4”
1/2”
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Ø,GP,JR,KH
10, 13, 15mm, 3/4” NO DRILL
–
3/4”
1/2”
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
–
3/4”
1/2”
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
–
3/4”
1/2”
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
Ø,GP,JR
10, 13, 15mm, 3/4” NO DRILL
78070
78058
Factory Tow – Package models only CH
3.5 5
25
3.5 6 30
3.5 6 30
3/4”, 13/16” 1/2”
5
6
3/4”, 13/16” 1/2”
5 5
6 30 6 15
15, 18, NO DRILL 21mm, 3/4”
30
n 33047 CA,GP
n 44525 Ø,JR
10, 13, 15mm, NO DRILL 3/4”
3.5 4
30
– – 85731 85731 –
n 33047 CA,GP n 44129 GP,JR l 33051 Ø,JF
13mm, 3/4”
1/2”
3/4”
1/2”
3.5 6 3.5 5 5 6
30 30 20
– 78022 74724
78058 78104 78104
5 5
6 6
40 45
5
6
20
8 8 8
20 20 25
74665 – 74682
78058 78058 78058
8
25
74682 – –
78058 78058 78104
–
85219 – –
74670
78058
–
–
74657
78013
HG
–
85243
78058
–
–
–
78013
–
–
78069
78058
–
–
–
78104
–
–
–
78058
–
78013
–
–
–
78058
–
–
–
78058
–
–
n 37012 Ø l 44067 Ø,JF
20 35 20 35 20 40 20 40 40 40 40 40 30 30 20 35 20 35 20 40 20 40 40 40 40
13mm, 3/4”
1/2”
13/16”, 7/8”, 1/2” 15/16” 3/4”, 15/16” 1/2” 13/16”, 1/2” 7/8”,15/16” 15, 18, 21mm, NO DRILL 3/4”, 15/16” 15, 18mm, 7/8” NO DRILL
3.5 6
l 33031 Ø,KL l 33031 Ø,KL n 44542 Ø,KL
13mm, 3/4”
NO DRILL
5 5 5
n 44542 Ø,KL
13mm, 3/4”
NO DRILL
5
n 44525 Ø,JR
15, 18mm, 7/8” NO DRILL
10, 13, 15mm, NO DRILL 3/4”
3.5 4
30
30
78058 78058 78104 78104 78104
OEM REPLACE. –
FOOTNOTES CH
WT. DISTRIB. INSTALL TIME
–
WT. CARRYING
85774
DRILL BITS
3.5 5.25 25
WRENCHES
78070
FOOTNOTES
CH
HITCH NUMBER
78058
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
85774
85774
n 44100 Ø Mountaineer Mountaineer Mountaineer Models w/1-1/4 Receivers Only Mountaineer Models w/1-1/4 Receivers Only Mystique Sable Sedan, All Models
25
3.5 5
– – CH CH –
– CH BN,GC
BN – – – –
– – – – – – – 74885
85219 85219 85219
–
9/16”
35
–
78104
–
–
9/16”
35
74665
78058
–
–
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
l 97232 Ø,HM 79-82 79-82 06-09 10-11 05-07
10, 18mm, NO DRILL 5/8” 10, 18, 22mm, NO DRILL 5/8”
20 l 97207 Ø, †
Marquis Sedan Marquis Wagon Milan Milan Montego
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
DRILL BITS 1”, 3/8”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
STANDARD WIRE
7/8”
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
T-CONNECTOR
n 06417 HM
08-11
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Mariner All, Inc. Hybrid
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
229
MERCURY
MERCURY
228
REESE TOWPOWER
CLASS II
CLASS I
Tracer Wagon
1997
n 77018 –
Tracer Wagon
98-99
n 77078 †,GP,JR
Villager Mini Van Villager Mini Van Villager Mini Van
93-97 1998 99-02
n 77110 EP n 77110 EP n 77110 EP
00-05
n 77093 AE
Eclipse Endeavor
06-12 04-05
n 77130 TA
Endeavor Galant Lancer
06-08 07-12 02-03
n 77209 Ø,JR,KH n 77032 –
Lancer All, Except Evolution,Ralliart & Models w/Dual Exhaust
08-11
n 77192 Ø,GP
01-06 97-04 03-06 07-10 11-12 11-12
Raider
06-09
RVR, Canada Only
NISSAN
200-SX Altima Altima Altima Altima 4 Dr. Sedan Altima 2 Dr. Coupe Armada
Armada Cube Frontier Pickup All, Inc. Desert Runner
10mm, 12mm, 14mm, 11/16” 10mm, 11/16”
–
–
– –
78104 78104
– –
– –
85743 74697 –
78104 78104 78104
–
– – –
–
78104
–
–
85252 – 85315 85745 85745 85758
78013 78013 78104 78104 78104 78104
BN,HG
CH
– – – – – –
74187
78058
BN
85253
85253
–
85758
78104
w/ Factory – 7-Way CH –
– – 74218 – 78094 78094 74682
78013 78013 78013 78104 78104 78013 –
74682 85713 74219
– 78013 78013
1/2”
40
15/32”
30
n 77273 Ø,GP,JR
10-12
n 77273 Ø,GP,JR
9/16”, 3/4”
NO DRILL
10mm, 11/16”, 3/4” 10mm, 7/8”
1/2”
30 15
NO DRILL
30
12, 13mm, 3/4”, NO DRILL 15/16” 12, 13mm, 3/4”, NO DRILL 15/16”
25
HITCH NUMBER
Ø,JR
18mm
NO DRILL
Ø,JR
10mm, 19mm NO DRILL
12, 13mm, 3/4”, NO DRILL 15/16”
10, 13, 14, 17mm NO DRILL
l 06131 Ø,HM
14, 17mm, 3/4”, 7/8”
l 06131 Ø,HM
Ø,†,JR Ø,HM,JR
12, 14, 17mm, 3/4” NO DRILL
Ø,HM,JR
12, 14, 17mm, 3/4” NO DRILL
Ø,JR,TA
9/16”, 11/16”, 3/4” NO DRILL
AE,HM,TA
16mm, 11/16”, 5/8” 7/16”
Ø,HM
3/4”
NO DRILL
14, 17mm, 3/4”, 7/8”
22mm, 1-1/8”
NO DRILL
5
8 20
n 33092 Ø,HM
16, 17mm, 11/16” 1” hole saw
3.5
25
10, 17, 19mm NO DRILL 17mm
NO DRILL
17mm, 3/4”
NO DRILL
17mm, 3/4”
NO DRILL
5 5
5.5 25 5.5 20
4 4
4 4
25 25
22mm, 1-1/8” NO DRILL
5
8
20
35 20 20 30 45 30 19mm
NO DRILL
19mm
NO DRILL
18mm
NO DRILL
6 6 6
10 15 10 15 10 15
45 n 37152 –
n 37042 –
n 88001 –
06996
20
30
l 37091 Ø l 44674 Ø, HM l 44596 Ø n 77233 HM,JR
3.5 5
30 n 51138 Ø,HM
– 77112 77112 77162 77168 77172
20 20 20 15
40 n 44579 Ø,HM,JR n 44579 Ø,HM,JR
n n n n n n
5 5 5 5
CH CG
25 n 33028 Ø,KH n 33044 Ø,GP
n 77048 Ø,KH
12, 13mm NO DRILL (x2), 17mm 12mm, 17mm NO DRILL
3.5 3.5 3.5 3.5
25
11-12
08-12 09-12 98-03
NO DRILL NO DRILL
NO DRILL NO DRILL
n 44561 Ø,JR
2012
97-98 93-97 98-01 02-06 07-13 08-12 04-07
18mm 10mm, 19mm
18mm 18mm
OEM REPLACE.
78013
1/2”
Ø,JR Ø,JR
FOOTNOTES
–
19mm, 11/16”
33001 33001 33001 33017
WT. DISTRIB. INSTALL TIME
–
– – –
n n n n
WT. CARRYING
– BN,HG
15 15 15 15
DRILL BITS
78013 – –
NO DRILL NO DRILL
WRENCHES
– 74219 –
18mm 18mm
FOOTNOTES
30 n 06961 Ø,JR 30 n 06961 Ø,JR 30 n 06961 Ø,JR n 06968 Ø,JR
1/2”
HITCH NUMBER
1/2”
19mm, 11/16”
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
–
DRILL BITS
–
WRENCHES
78013
FOOTNOTES
–
STYLE
20
WT. CARRYING WT. DISTRIB. INSTALL TIME
1/2”
DRILL BITS
–
WRENCHES
–
FOOTNOTES
78013
HITCH NUMBER
–
INSTALL TIME STYLE
35
DRILL BITS
9/16”
WRENCHES
–
FOOTNOTES
–
HITCH NUMBER
78058
IONSTALL TIME STYLE
74665
DRILL BITS
30
n 33080 Ø,JR
n 77273 Ø,GP,JR Lancer, 4 Dr. Sedan, Except Evolution, Ralliart & Models w/Dual Exhaust Lancer Sportback, 5 Dr. Hatchback, Except Ralliart & Models w/Dual Exhaust Montero, not Inc. Montero Sport Montero Sport Outlander Outlander Outlander, All, Except Outlander Sport Outlander Sport, All Styles
1/2”
3/4”, 11/16”, 13/16” 9/16”, 11/16”, 13/16” 10mm, 3/4”, 11/16”, 13/16” 19mm, 11/16”
15, 18, 21mm, 9/16", 11/16", 3/4", T50
7/16", 1/2" 45
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
n 33048 –
3/4”, 9/16”
1/2”
4
5
30
1/4”, 1/2”, 5 9/16”
6.5 35
n 44148 –
3/4”
1/2”
4
5
30
74219
– HG CH CH
– – HG – CG CG BO BO CG BN,HG
– – – – – – 85219 85219 – –
HG
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
231
APPLICATIONS GUIDE
Eclipse All, Inc. Spider
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
STANDARD WIRE
n 77022 –
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
T-CONNECTOR
98-99
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Tracer Sedan
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
Up to 200 lb TW Up to 2000 lb GTW
MITSUBISHI
APPLICATIONS GUIDE
REESE TOWPOWER
MERCURY - NISSAN
MERCURY - NISSAN
230
REESE TOWPOWER
REESE TOWPOWER
n 37042 –
n 88001 –
n n l l l n
77248 77280 77028 77028 77028 77162
Maxima All Models
09-12
n 77168 AE,HM,TA
Murano
03-07
TA
7/8”
1/2”
Ø,JR,TA
9/16”, 11/16”, 3/4” 16mm, 11/16”, 5/8”
NO DRILL
40 25 30 30 30 30
7/16”
45
Ø,HM,JR
17mm,18mm,19mm
NO DRILL
HM,JR
3/4”
1/2”
TA
7/8”
1/2”
TA
7/8”
1/2”
Murano NV1500 NV2500 HD NV3500 HD Pathfinder 2 & 4 Dr.
09-12 2012 2012 2012 87-95
n 06048 –
Pathfinder 2 & 4 Dr.
96-04
n 06061 Ø,HM
Pickup (App. starts with 86-1/2)
18,19mm, 3/4”, 7/8” 17mm
40
–
20 l 51046 Ø,HM n 37152 –
n 37042 –
Pickup
15, 18, 21mm, 9/16", 11/16", 3/4", T50
n 37152 –
Mini Van Mini Van Mini Van Mini Van Mini Van
93-97 1998 99-02 04-09 11-12
n 77110 EP n 77110 EP n 77110 EP
Rogue All, Except Krom Sentra All, Inc. SE-R & SE-R SPEC V
08-13 00-02
n 77126 Ø,TA
Sentra All, Inc. SE-R & SE-R SPEC V
03-06
n 77126 Ø,TA
Sentra
07-12
n 77166 TA
Titan Pickup Crew Cab 5.6 ft. Bed
04-12
19mm, 11/16”
1/2”
19mm, 11/16”
1/2”
19mm, 11/16”
1/2”
30 n 06961 Ø,JR 30 n 06961 Ø,JR 30 n 06968 Ø,JR
19mm
NO DRILL
18mm
NO DRILL
10mm, 19mm
NO DRILL
78013
5
8 30
n 44526 Ø,GP
17mm 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
NO DRILL
5
5.5 20
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 30
33069 44583 44600 44664 44664 44664 44152
19mm
NO DRILL
Ø,JR
12, 17, 19mm NO DRILL
Ø,JR
12, 17, 19mm NO DRILL
Ø,GP,JR
10, 16, 17, 19mm NO DRILL
Ø,HM
17mm
NO DRILL
Ø,HM
17mm
NO DRILL
Ø,HM
17mm
NO DRILL
HM,JR
13, 19mm, 3/4”, 7/8” 17mm
1/2” NO DRILL
17mm
NO DRILL
l 33050 Ø n 44132 Ø
5
8
30
3.5 3.5 4 7.5 7.5 7.5 3.5
30 30 35 10 20 10 20 10 20 5 40
5 5
5.5 20 5.5 20
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
n 33048 –
3/4”, 9/16”
1/2”
4
5
30
1/4”, 1/2”, 5 9/16”
6.5 30
n 44148 –
3/4”
1/2”
4
5
30
n n n n l
33001 33001 33017 33079 44663
NO DRILL
3.5 3.5 3.5 3.5 3.5
NO DRILL
3.5
Ø,JR
18mm
NO DRILL
Ø,JR
18mm
NO DRILL
Ø,JR
10mm, 19mm NO DRILL
Ø,JR
10, 12, 18mm NO DRILL
Ø,HM,JR
18, 19mm, 6” ratchet extension 18, 19mm
5 5 5 5
–
HG
85757 85763 85755 85755 – – – 78094
78013 78058 78104 78013 78013 78104 78104
CH
– – – –
78107
78104
CH
–
–
Dealer
–
–
78107 85775 85775 85775 74494
78104 78104 78104 78104 78013
CH
CH
– – – – –
74218
78013
HG
–
74494
78013
BN,HG
–
74494
BN BN, BO CH
– 85763 –
CH – – –
CH CH CH
HG
78013
74494
15 15 15
BN,HG
OEM REPLACE.
74219
FOOTNOTES
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
STANDARD WIRE
30
T-CONNECTOR
5
HITCH NUMBER
DRILL BITS
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE 4
7/16", 1/2" 45
15, 18, 21mm, 9/16", 11/16", 3/4", T50 18mm
BN,HG
–
HG
20 20 15 20 35
– 74219 – 78093 85770
78013 – – 78104 78104
BN,CH
20
– BN,HG – CH
– – – – –
NO DRILL
20
78108 –
78104 78013
–
– –
NO DRILL
20
–
78013
–
–
NO DRILL
30
78094
78104
CH
–
74682
78058
BO
85219
l 51106 Ø,RT 06996
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS NO DRILL
n 44592 Ø,GP 3/4”, 7/8”, 11/16” 3/4”, 7/8”, 11/16” 3/4”, 7/8”, 11/16”
1/2”
74494
n 37042 –
Quest Quest Quest Quest Quest
6.5 35
3/4”, 9/16”
7/16", 1/2" 30
88-97
n 88001 –
1/4”, 1/2”, 5 9/16”
n 33048 –
n n n n n n n
1/2”
86-87
n 88001 –
6
74219 n 51147 Ø,GP
11-12 11-12 95-99 00-02 2003 04-08
1/4”, 1/2”, 5 9/16”
7/16", 1/2" 45
05-12
JUKE, AWD Only JUKE, FWD Only Maxima Sedan Maxima Sedan Maxima Sedan Maxima All Models
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
19mm
NO DRILL
6
10 15
l 37092 Ø
19mm
NO DRILL
6
10 15
CH
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
Frontier Pickup
15, 18, 21mm, 9/16", 11/16", 3/4", T50
WRENCHES
FOOTNOTES
HITCH NUMBER
n 37152 –
2004
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Frontier Pickup All, Inc. Desert Runner
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
233
NISSAN
NISSAN
232
REESE TOWPOWER
Xterra
00-04
Xterra
05-12
X-Trail All Models (Canada Only)
05-06
88 88 88 88 98 98 98 98 98 98
1977 78-79 80-85 86-89 1977 78-84 86-89 1977 78-84 86-89
OLDSMOBILE RWD RWD RWD FWD
n 77170 HM n 77170 HM l 77275 HM,JR,KH
3/4”
1”
3/4”
1”
10mm, 11/16”, 3/4”
1/4”
10, 16, 17mm
NO DRILL
06003 06003 06003 06615 06003 06003 06003 06003 06003 06615 88002 06073 88002 06073 88002 06027 06299 06285
00-03
n 06976 HM,JR
Bravada
06996
OEM REPLACE.
FOOTNOTES
STANDARD WIRE
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
l 33019 Ø
7/8”
NO DRILL
3.5 5.5 15
74897
78058
n 44529 Ø
18, 19mm
NO DRILL
3.5 5.5 30
85757 85763
78058 78058
–
78013
– – – – – – – – – –
78058 78058 78104 78013 78058 78058 78058 78058 78058 78058
–
– – – – – – – – – –
–
–
–
–
BN, Fact. – 7-Way models only BN – BN, Fact. 85763 7-Way models only – –
–
1/2”
30
–
–
–
–
– –
– –
– –
– –
–
–
–
–
–
–
–
85219
–
–
3/4”
1/2”
3/4”, 9/16”
1/2”
–
3/4”
1/2”
–
3/4”, 9/16”
1/2”
–
3/4”
1/2” NO DRILL
Ø,JR,KH
7, 10, 13mm, 3/4”
–
13mm, 3/4”, 7/8” 1/2”
GP,JR
13, 15mm, 9/16”, 3/4”, 7/8” 15, 17mm, 9/16”, 3/4” 15, 17mm, 9/16”, 3/4” 3/4”
1/2”
30
1/2”
18mm, 7/8”
NO DRILL
30 15 n 51031 Ø, FP, HM, KK 18mm,
14mm, 9/16”, 11/16”
CH CH
1/2”
– –
18mm, 7/8”
BO CH
85219 85219 85219 – –
– – –
9/16", 5/8”, 11/16” 3/8”, 1/2” 7, 13, 15mm, 11/16” 1/2”
18mm, 7/8”
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
STYLE
3.5 5.5 15
BO BO
–
– †,AO
n 06409 –
77-90
NO DRILL
78058 78058 78058 78104 78104
–
9/16", 5/8”, 11/16” 3/8”, 1/2” 9/16", 5/8”, 11/16” 3/8”, 1/2”
n 33014 Ø l 33015 Ø,SD
18mm
NO DRILL
18mm, 7/8”
NO DRILL
6 30 6 30 6 15
n 33021 Ø n 44098 Ø,HM
NO DRILL
4
6 15
l 37051 FP,JT,KK 18mm, 3/4” 1/2” l 37041 FP,JT,KK 18mm, 3/4” 1/2” NO DRILL n 51031 Ø, FP, HM, KK 18mm,
5 5 4
6 30 6 30 6 15
NO DRILL
NO DRILL
4
6 15
l 37051 FP,JT,KK 18mm, 3/4” 1/2” l 37041 FP,JT,KK 18mm, 3/4” 1/2” NO DRILL n 51031 Ø, FP, HM, KK 18mm,
5 5 4
6 30 6 30 6 15
1-1/8” 3/4”
NO DRILL
4
6 15
1/2”
3/4”
1/2” NO DRILL
5 5 4
NO DRILL
18mm, 1-1/8” 15 n 51031 Ø, FP, HM, KK 18mm, 1-1/8”
1-1/8” 15 n 51031 Ø, FP, HM, KK 18mm, 1-1/8”
1-1/8”
Custom Cruiser Wagon Full Size
DRILL BITS
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
WRENCHES 7/8”
74682 74682 74682 85768 85768 85768
– – –
†,AO –
n 06955 Ø,FP,GP,KK
99-01
NO DRILL
10 15 10 15 10 15
– – –
9/16", 5/8”, 11/16” 3/8”, 1/2” 9/16", 5/8”, 11/16” 3/8”, 1/2”
n 06955 Ø,FP,GP,KK
1998
19mm
6 6 6
–
– –
l 37051 JT l 37041 JT n 51031 Ø,HM
Bravada
NO DRILL NO DRILL
–
9/16", 5/8”, 11/16” 3/8”, 1/2” 7, 13, 15mm, 11/16” 1/2”
n 88002 – n 06955 Ø,GP
91-94 96-97
19mm 19mm
–
– AO,GP
n 51173 HM,JR Bravada Bravada
NO DRILL
l 37092 Ø l 37092 Ø l 37092 Ø
10 15 10 15 10 15
–
9/16", 5/8”, 11/16” 3/8”, 1/2” 9/16", 5/8”, 11/16” 3/8”, 1/2”
Aurora
91-96
19mm
6 6 6
30 30 30 30 30 30 40 30 30 40 35 40 35 40 35 40 20 35
– –
92-98 99-04 95-99
98 Regency Includes Touring Sedan
1990
NO DRILL NO DRILL
45
Achieva Alero Aurora
98 Regency Includes Touring Sedan
DRILL BITS
l 51109 Ø,RT
n 77096 Ø,EP
19mm 19mm
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
25 25 30
n n n n n n n n n n n n n n n n n n
FWD Regency Regency Regency FWD
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
l 51106 Ø,RT l 51106 Ø,RT l 51106 Ø,RT
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW WT. CARRYING WT. DISTRIB. INSTALL TIME
04-12 04-12 04-12 07-12 07-11 2012
STYLE
YEAR
MODEL
Titan Pickup Crew Cab 7.25 ft. Bed Titan Pickup King Cab 6.5 ft. Bed Titan Pickup King Cab 8 ft. Bed Versa Hatchback Versa Sedan
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
7/16”
30
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
3.5 6 4 6
60 15
18mm, 1-1/8” NO DRILL
4 4
6 6
20 20
l 33015 Ø,FP,KK,SD 18mm, 7/8” NO DRILL
4
6
15
n 33021 Ø,FP,KK
18mm, 1-1/8” NO DRILL
4
6
20
n 44098 Ø, FP, HM, KK 18mm, 1-1/8” NO DRILL
4
6
20
l 33015 Ø,FP,KK,SD 18mm, 7/8” NO DRILL
4
6
15
n 33021 Ø,FP,KK
18mm, 1-1/8” NO DRILL
4
6
20
n 44098 Ø, FP, HM, KK 18mm, 1-1/8” NO DRILL
4
6
20
18mm, 1-1/8” NO DRILL
– – – – – – – – –
–
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
235
APPLICATIONS GUIDE
APPLICATIONS GUIDE
REESE TOWPOWER
NISSAN - OLDSMOBILE
NISSAN - OLDSMOBILE
234
REESE TOWPOWER
CLASS II
Cutlass RWD
78-80
n 88002 – n 06407 –
Cutlass 4 Dr., FWD Cutlass Ciera FWD
97-00 85-88
Cutlass Ciera FWD
89-96
n 06220 Ø,JR,X
Cutlass Ciera Cruiser Wagon RWD Cutlass Ciera Cruiser Wagon FWD
78-83
n 06407 –
84-96
n 06054 Ø,AI,FM
Cutlass Supreme 4 Dr. RWD Cutlass Supreme 2 Dr. RWD Cutlass Supreme 2 Dr. FWD
81-87 81-88 88-93
Cutlass Supreme 4 Dr. FWD
90-91
Cutlass Supreme 2 Dr. FWD w/ Aero Sport Pkg. Cutlass Supreme 4 Dr. FWD
92-93 92-97
Cutlass Supreme 2 Dr. FWD
94-97
Delta Delta Delta Delta
1977 78-79 80-85 86-89
88 88 88 88 FWD
Delta 88
Delta 88
n 77001 AI,JR,TA
13mm, 3/4”
NO DRILL
15 n 06249 – n 06220 Ø,JR,X
n n n 10, 15mm, 11/16” 1/8”, 7/16”, 40 n
92-95
96-99 98-02
LSS LSS LSS Regency Royale Royale Royale Silhouette Silhouette Silhouette All, Inc. AWD
90-91 92-95 96-99 97-98 90-91 92-95 96-99 90-92 93-96 97-04
88002 06407 06407 06411
10, 15mm, 11/16” 1/8”, 7/16”, 40 9/16”
n 77109 TA
n 77070 JR
n 77070 JR
n 77040 AL,GP,JR
10, 13, 15mm, 9/16” 1/2”
7/8”
1/2”
10, 13, 15mm, 9/16” 1/2”
10, 13, 15mm, 9/16” 1/2”
10, 15mm, 3/4”, 7/8”
1/2”
20
30
20
20
30
–
–
NO DRILL
40
–
–
–
–
35 30 9/16”, 11/16”, 7/8” 3/8” 30 10, 15mm, 11/16” 1/8”, 7/16”, 60
– – –
– – –
– – –
– – –
–
–
–
–
–
–
–
–
WRENCHES 13mm, 7/8”
9/16”, 11/16”, 7/8” 3/8”
– AI,JR,TA
OEM REPLACE.
–
FOOTNOTES
–
WT. DISTRIB. INSTALL TIME
30
WT. CARRYING
3/8”
DRILL BITS
–
WRENCHES
–
FOOTNOTES
–
3.5 10 40
HITCH NUMBER
–
13/32”
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
40
13, 14mm, 3/4”
DRILL BITS
NO DRILL
n 33007 –
WRENCHES
– –
FOOTNOTES
–
HITCH NUMBER
– –
STYLE
– –
1/2”
WT. CARRYING WT. DISTRIB. INSTALL TIME
20 40
–
NO DRILL
13mm, 9/16”, 3/4”, 7/8” 13mm, 9/16”, 3/4”, 7/8” 9/16”, 11/16”, 7/8”
DRILL BITS
–
WRENCHES
–
1/2” 3/8”
FOOTNOTES
–
INSTALL TIME STYLE
–
DRILL BITS
30 30
3/4” 9/16”, 11/16”, 7/8” 13mm, 3/4”
3/4”
1/2”
9/16”
HB,JR,TA n 06305 AW,FE, HB,JR,TA
10, 15mm, 11/16” deep socket 10, 15mm, 11/16” deep socket
1/8”, 7/16”, 60 9/16” 1/8”, 7/16”, 60 9/16”
n 06411 AI,JR,TA
10, 15mm, 11/16” deep socket
1/8”, 7/16”, 60 9/16”
–
–
–
–
n 06305 AW,FE,
10, 15mm, 11/16” 1/8”, 7/16”, 60 deep socket 9/16” 9/16", 5/8”, 11/16” 3/8”, 1/2” 30
–
–
–
–
– – – –
– – – –
–
–
– – – –
–
–
–
–
–
–
–
–
– –
– –
– –
– –
– – – – – – – – 74492 74207
– – – – – – – – 78104 78013
n n n n n n n n n n n n n n n n n n n n n n
06003 06615 88002 06073 06615 88002 06367 06615 88002 06306 06384 51183 06073 06367 06306 06306 06073 06367 06306 06302 06302 06302
– AO,GP – – AO,GP – GP,JR AO,GP – GP,KH GP,JR GP,JR – GP,JR GP,KH GP,KH – GP,JR GP,KH AL,JR AL,JR AL,GP,JR
30 9/16", 5/8”, 11/16” 3/8”, 1/2” 30 7, 13, 15mm, 11/16” 1/2” 30 3/4” 1/2” 40 3/4”, 9/16” 1/2” 40 7, 13, 15mm, 11/16” 1/2” 30 3/4” 1/2” 40 10, 13, 15mm, 9/16” 1/2” 40 7, 13, 15mm, 11/16” 1/2” 30 3/4” 1/2” 40 10, 13, 15mm, 9/16” 1/2” 30 3/4”, 7/8” 1/2” 30 3/4”, 7/8” 1/2” 30 3/4”, 9/16” 1/2” 40 10, 13, 15mm, 9/16” 1/2” 40 10, 13, 15mm, 9/16” 1/2” 30 10, 13, 15mm, 9/16” 1/2” 30 3/4”, 9/16” 1/2” 40 10, 13, 15mm, 9/16” 1/2” 40 10, 13, 15mm, 9/16” 1/2” 30 10, 15mm, 3/4”, 7/8” 1/2” 40 10, 15mm, 3/4”, 7/8” 1/2” 40 10, 15mm, 3/4”, 7/8” 1/2” 40 9/16", 5/8”, 11/16” 3/8”, 1/2”
n 33068 †,AL n 33068 †,AL n 33094 AL,JR
1/2”
10, 15mm, 3/4”, 7/8”
1/2”
3.5 5
13mm, 9/16” 1/2”
–
– – – – – – – – – HG
– – – – – – – – – –
10, 15mm, 3/4”, 7/8” 1/2”
40 n 51079 AL,GP,JR
13mm, 9/16”, 3/8” 11/16” 13, 16, 17mm, 3/4”, 1/2” 9/16”, 11/16”
40
–
78104
–
40
–
78013
–
89-95
n 06097 –
Breeze
96-00
n 06977 JR
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
10, 15mm, 3/4”, 7/8”
1/2”
3.5 5 40
n 44574 AL,JR
10, 15mm, 3/4”, 7/8”
3.5 3.5 30 3.5 3.5 30 3.5 5 40
13mm, 9/16” 1/2”
–
n 51102 AL,GP,JR
Acclaim
06996
–
–
HB,JR,TA n 06003 – n 06003 –
n 77070 JR
–
30
–
n 06305 AW,FE,
n 77001 AI,JR,TA
78058
7/16”
14mm, 9/16”, 11/16”
deep socket
9/16”
90-91
Delta 88 Intrigue
PLYMOUTH
n 77076 Ø,GP
STANDARD WIRE
n 06409 –
WIRING
Up to 2500 lb TW Up to 18000 lb GTW T-CONNECTOR
91-92
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
74491
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Custom Cruiser Wagon Full Size
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
40
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
237
APPLICATIONS GUIDE
APPLICATIONS GUIDE
REESE TOWPOWER
OLDSMOBILE - PLYMOUTH
OLDSMOBILE - PLYMOUTH
236
REESE TOWPOWER
REESE TOWPOWER
n 06080 GW,GP
84-90
11/16”, 7/8”
15/32”
n 37042 JT n 88001 JT Grand Voyager Long Wheelbase, 2 WD Only
n 06080 GP
91-95
15, 18, 21mm, 9/16", 11/16", 3/4", T50 11/16”, 7/8”
96-00
n 77012 Ø,HM
18, 19mm
NO DRILL
30 n 06369 Ø,GP
15/32”
30 n 37152 –
Neon 2 & 4 Dr. Neon 2 & 4 Dr. Trailduster Trailduster w/Skid Shield Trailduster Trailduster w/Skid Shield Voyager
95-99 00-01 All, Except w/Skid Shield 74-85 w/Deep Drop Bumper, Except 74-85
n 77121 – n 77052 GP,JR
11/16”, 7/8”
7/16”
7/8”
1/2”
6.5 30
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 30
–
30 n 51062 HM
n 06080 GW,GP
11/16”, 7/8”
15/32”
15, 18, 21mm, 9/16", 11/16", 3/4", T50
n 06080 GW,GP 18, 19mm
NO DRILL
30 n 06369 Ø,GP
15, 18, 21mm, 9/16", 11/16", 3/4", T50 11/16”, 7/8” 18, 19mm
–
19mm, 3/4” 1/2” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
3.5 3.5 30
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 40
15, 18, 21mm, 9/16", 11/16", 3/4", T50
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 30
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 30
30 30 n 51062 HM
n 37042 –
n 88001 –
OEM REPLACE.
FOOTNOTES
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
STANDARD WIRE
–
1/2”
3.5 3.5 30
74187
78058
BN
–
n 33045 – n 44006 HM
15, 17, 18, 19mm, 7/8” 19mm, 3/4”
7/16”
3.5 5
30
1/2”
3.5 3.5 30
74658
78013
BN
–
HG
n 37081 M,TH
13, 18, 19mm, NO DRILL 7/8”
5
10 45
– – – –
n 37081 M,TH
13, 18, 19mm, NO DRILL 7/8”
5
10 45
74182 74182
78058 78058
–
– –
n 33046 †,JT
3/4”
3.5 3.5 30
74182
78058
–
–
78058
BN
–
78058 78058 78013
BN BN
– – –
1/2”
78058 78058 78058 78058
–
– – – –
– – –
n 33046 †,JT
3/4”
1/2”
3.5 3.5 30
74187
74187
n 37152 –
06996
3/4”
7/16", 1/2" 30 15/32”
78058
74051
n 37042 JT
n 77012 Ø,HM
n 33046 †
7/16", 1/2" 30
n 37152 JT
n 88001 JT
–
74658
30 n 37152 JT
91-95
91-95 91-95 96-00
3.5 3.5 30
30 20
n 88001 JT
Voyager Short Wheelbase, 2 & 4 WD Voyager Short Wheelbase, 2 WD Only Voyager All, Inc. 4 WD
1/2”
7/16", 1/2" 45
n 37042 JT
Voyager
3/4”
74187
All, Except w/Skid Shield 86-88 w/Deep Drop Bumper, Except 86-88 84-90
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
1/4”, 1/2”, 5 9/16”
n 33046 †,JT
7/16", 1/2" 30
n 37042 – 15, 18, 21mm, 9/16", 11/16", 3/4", T50
6
74051
n 37152 –
n 88001 –
1/4”, 1/2”, 5 9/16”
7/16", 1/2" 45
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
19mm, 3/4” 1/2” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
3.5 3.5 30
1/4”, 1/2”, 5 9/16”
6
1/4”, 1/2”, 5 9/16”
6.5 40
n 44618 – n 33046 – n 33045 – n 44006 HM
3/4”
1/2”
15, 17, 18, 19mm, 7/8” 19mm, 3/4”
7/16”
3.5 5 30 3.5 3.5 30 3.5 5 30
1/2”
3.5 3.5 30
7/8”, 11/16” 1/2”
74187 74187 74658
74658
HG
HG
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
Grand Voyager All, Inc. 4 WD
15, 18, 21mm, 9/16", 11/16", 3/4", T50 18, 19mm
15,17,18, 19,21, 22mm,T-50, 9/16”,3/4” 15,17,18, 19,21, 22mm,T-50, 9/16”,3/4”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
7/16", 1/2" 30
n 37042 – n 88001 –
WRENCHES
FOOTNOTES
HITCH NUMBER
30 n 37152 JT
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Grand Voyager
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
239
PLYMOUTH
PLYMOUTH
238
REESE TOWPOWER
REESE TOWPOWER
85-91
n 06220 Ø,JR,X
6000 Wagon Aztek All, Inc. AWD
84-91 01-05
n 06054 Ø,AI,FM n 06457 –
APPLICATIONS GUIDE
n 77070 JR
10, 13, 15mm, 9/16” 1/2”
96-99 00-05
n n n n 20 n n n n
06003 06003 06003 06407 06367 06615 06306 06976
– – – – GP,JR AO,GP GP,KH HM,JR
n 51173 HM,JR Bonneville Wagon Catalina Catalina Firebird Includes Formula Firebird Trans Am G3 5 Dr. G3 Wave 5 Dr. (Canada Only) G5 All, Except GT G5 GT G5 Pursuit 2 Dr. (Canada Only) G5 Pursuit 4 Dr. (Canada Only) G5 Pursuit GT 2 Dr. (Canada Only) G5 Pursuit GT 4 Dr. (Canada Only)
82-83 1977 78-81 93-02 93-02 2009 2009 07-09 07-09 05-07 05-07 05-07 05-07
n 06407 – n 06003 – n 06003 –
l l n n n n n n n n n
77097 77097 77122 77132 51164 77122 77122 77132 51164 77132 51164
HM,JR
3/4”
1/2”
HM,JR
3/4”
1/2”
30 30 40 25 25 40 40 25 25 25 25
10, 13, 15mm, 11/16”, 3/4”
NO DRILL
45
–
3/4”, 7/8”
1/2”
–
3/4”, 7/8”
1/2”
JR
3/4”
1/2”
HM,JR
3/4”
1/2”
HM,JR
3/4”
1/2”
JR
3/4”
1/2”
JR
3/4”
1/2”
HM,JR
3/4”
1/2”
HM,JR
3/4”
1/2”
G6 All Models G8 All Models
05-09 08-09
n 06463 GP
Grand Am All Models Grand Am w/Steel Bumper Reinforcement Grand Am All, Inc. GT Models
78-80 78-80 92-98
n 06407 – n 06407 – n 06027 Ø,JR,KH
Grand Am All, Inc. GT Models Grand Prix
99-05 78-87
n 06299 – n 06407 –
Grand Prix All, Except SE & Turbo
88-90
n 77001 AI,AY JR,TA
Grand Prix 2 & 4 Dr., Except Turbo
91-93
n 77001 AI,AY JR,TA
Grand Prix 4 Dr. STE
91-93
n 77193 Ø,JR,KH
10, 15mm, 11/16” 1/8”, 7/16”, 40 9/16” 10, 15mm, 11/16” 1/8”, 7/16”, 40 9/16”
n 06411 AI,JR,TA
OEM REPLACE.
FOOTNOTES –
– – – – – 85709 78043 78043 78043
78058 78058 78058 78104 78104 78058 78058 78058 78058
78043 78043 78043
78058 78058 78058
–
– – –
78043
78058
–
–
74716 –
78058 78013
– –
– –
30 30 40
– – –
78058 78058 78013
–
20
– –
78013 78058
–
– –
–
78104
–
–
– –
–
– – – – – – –
30
30
9/16”, 11/16”, 3/8” 30 7/8” 10, 15mm, 11/16” 1/8”, 7/16”, 60 deep socket 9/16”
– – – – – CG – – – – –
– –
–
– – – – – – – – –
– – –
n 06305 AW,FE,HB,
10, 15mm, 11/16” deep socket 10, 15mm, 11/16” deep socket
1/8”, 7/16”, 60 9/16” 1/8”, 7/16”, 60 9/16”
–
78104
–
–
–
78013
–
–
–
78013
–
–
– –
78058 78058
–
35
–
– –
3/8”
30 30
– –
78058 78013
–
– –
3/8”
30
–
78013
–
–
JR,TA n 06353 JR n 06262 JR
78-81
n 06407 – 06996
STANDARD WIRE 78104 78104
– –
–
Le Mans w/Steel Bumper Reinforcement
30 20
T-CONNECTOR – –
9/16”, 1/16”, 3/8” 3/4”
55 40
–
n 06003 – n 06407 –
1/2” NO DRILL
WT. DISTRIB. INSTALL TIME
–
40
3.5 – 3.5
78104
77-81 78-81
7/8” 9/16”, 11/16”, 7/8”
WT. CARRYING
78058 78058 78058 78058 78104
3.5
NO DRILL
–
n 06305 AW,FE,HB,
n 77109 TA l 77077 Ø,TA
DRILL BITS
– – – – –
9/16”, 11/16”, 3/8” 3/4”
15mm, 3/4”
10, 15mm, 11/16” 1/8”, 7/16”, 60 deep socket 9/16”
Grand Prix SE Sedan Grand Prix GT Coupe & Sedan Inc. GTP Package Grand Ville Le Mans All Models
97-03 97-08
WRENCHES
– –
n 33061 Ø n 44538 –
n 06411 AI,AY,JR,TA JR,TA n 06305 AW,FE,HB, JR,TA
Grand Prix 2 Dr. SE w/Sport Appearance 91-96 Package & GT Models 94-96 Grand Prix 2 & 4 Dr.
FOOTNOTES
– BN
30 30 9/16", 5/8”, 11/16” 3/8”, 1/2” 30
7mm, 10mm, NO DRILL 13mm, 3/4” 13mm, 3/4”, 7/8” 1/2”
HITCH NUMBER
78107 78058
9/16", 5/8”, 11/16” 3/8”, 1/2”
9/16”, 11/16”, 7/8” 3/8”
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
– 85261
30 30 9/16", 5/8”, 11/16” 3/8”, 1/2” 30 9/16”, 11/16”, 7/8” 3/8” 30 10, 13, 15mm, 9/16” 1/2” 40 7, 13, 15mm, 11/16” 1/2” 30 10, 13, 15mm, 9/16” 1/2” 30 15, 17mm, 1/2” 30
9/16”, 11/16”, 7/8” 3/8”
DRILL BITS
–
9/16", 5/8”, 11/16” 3/8”, 1/2”
10mm, 9/16”, 3/4” 1/2”
WRENCHES
–
9/16", 5/8”, 11/16” 3/8”, 1/2”
9/16”, 3/4” 15, 17mm, 1/2” 9/16”, 3/4” 9/16”, 11/16”, 7/8” 3/8”
FOOTNOTES
78104
10, 15mm, 11/16” 1/8”, 7/16”, 60 deep socket 9/16” 7/8”, 3/4” 1/2” 30 3/4”, 7/8”
1/2”
9/16", 5/8”, 11/16” 3/8”, 1/2” 9/16”, 11/16”, 7/8” 9/16”, 11/16”, 7/8”
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
–
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
Bonneville All, Except SLE, SSE & SSEi Bonneville All Models
1977 78-81 80-81 82-86 92-95
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
–
n 51151 HM Bonneville Bonneville Bonneville Bonneville Sedan Bonneville All, Except SSE & SSEi
STYLE
40 40
WT. CARRYING WT. DISTRIB. INSTALL TIME
NO DRILL
9/16”, 11/16”, 3/4” 3/8”
DRILL BITS
40
WRENCHES
NO DRILL
FOOTNOTES
13mm, 9/16”, 3/4”, 7/8” 13mm, 7/8”
HITCH NUMBER
INSTALL TIME STYLE
DRILL BITS
6000 All, Except AWD Models
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL PONTIAC
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
241
PONTIAC
PONTIAC
240
REESE TOWPOWER
REESE TOWPOWER
78-81
Montana All, Inc. AWD
99-05
n 06407 – n 77040 AL,GP,JR
10, 15mm, 3/4”, 7/8”
1/2”
30 n 06302 AL,GP,JR n 51102 AL,GP,JR
Montana SV6 All, Inc. AWD
n 06302 AL,GP,JR
05-06
n 51102 AL,GP,JR Montana SV6 All, Inc. AWD (Canada Only)
n 06302 AL,GP,JR
07-09
Parisienne
83-86
n 06003 –
Parisienne Wagon
83-86
n 06409 –
Safari Wagon Full Size
77-89
n 06409 –
Solstice Solstice GXP Solstice Solstice GXP Sunbird Sunbird GT Sunfire All, Except GT
06-08 07-08 2009 2009 88-94 88-89 95-99
n n n n n n n
77206 77206 77206 77206 77101 77101 77049
Sunfire GT Torrent
95-99 2006
Torrent
07-09
Trans Sport Van Trans Sport Van Trans Sport Van
n 77069 JR,KH
Vibe All, Except GT Models
03-08 09-10
Wave 5 Dr. (Canada Only)
04-08
Pickup, Ram, Full Size 1500 Only
09-13
Pickup, Ram, Full Size 1500 Only RAM, 3500 HD Chassis Cab, w/34 Wide Frames RAM, 4500 HD Chassis Cab, w/34 Wide Frames RAM, 5500 HD Chassis Cab, w/34 Wide Frames
10-13 11-12
RAM TRUCKS
n n n n l
77183 51169 77183 51169 77097
40 n 51079 AL,GP,JR
1/2”
40
1/2”
40 n 51079 AL,GP,JR
1/2”
40
1/2”
40 n 51079 AL,GP,JR
3/8”, 1/2”
85344
78058
HG
–
85344
78058
BN
–
30
–
78058
–
–
7/16”
30
–
–
–
–
7/16”
30
–
78058
–
–
– – – – – – –
78058 78058 78058 78058 78013 78013 78058
–
–
– – – – – – –
10, 15mm, 3/4”, 7/8”
1/2”
3.5 5 40
n 44574 AL,JR
10, 15mm, 3/4”, 7/8” 10, 15mm, 3/4”, 7/8” 10, 15mm, 3/4”, 7/8” 10, 15mm, 3/4”, 7/8”
1/2”
3.5 5
40
1/2”
3.5 5
40
1/2”
3.5 5
40
1/2”
3.5 5
40
1/2”
3.5 5
40
n 33094 AL,JR 10, 15mm, 3/4”, 7/8”
1/2”
3.5 5 40
n 44574 AL,JR n 33094 AL,JR
10, 15mm, 3/4”, 7/8”
1/2”
3.5 5 40
n 44574 AL,JR
10, 15mm, 3/4”, 7/8”
78058
–
–
7/16”
40
1/2”
40
– 78028
– 78013
– CG
– –
1/2”
Ø,HM
19mm
NO DRILL
19mm
NO DRILL
Ø,HM
19mm
NO DRILL
Ø,HM
19mm
NO DRILL
–
3/4”, 7/8”
1/2”
06391 51185 06391 51185
Ø,HM
18,19mm, 3/4”
NO DRILL
Ø,HM
18,19mm, 3/4”
NO DRILL
Ø,HM
18,19mm, 3/4”
NO DRILL
Ø,HM
18,19mm, 3/4”
NO DRILL
30 n 06302 AL,GP,JR
5, 10, 13mm, 7/8” #11 (.191 DIA.), 1/2” 10, 15mm, 1/2” 3/4”, 7/8” 10, 15mm, 3/4”, 7/8”
1/2”
25 n 51193 Ø,HM 25 25 n 51193 Ø,HM 25
18,19mm, 3/4” NO DRILL
3.5 4 30
18,19mm, 3/4” NO DRILL
3.5 4 30
40 40 n 51079 AL,GP,JR 40
10, 15mm, 3/4”, 7/8”
1/2”
3.5 5 40
n n n n n n n
44637 44630 44637 44630 33068 33068 33068
Ø,HM
18,19mm, 3/4” NO DRILL
Ø,†,HM
18,19mm, 3/4” NO DRILL
Ø,HM
18,19mm, 3/4” NO DRILL
Ø,†,HM
18,19mm, 3/4” NO DRILL
†,AL
13mm, 9/16” 1/2”
†,AL
13mm, 9/16” 1/2”
†,AL
13mm, 9/16” 1/2”
3.5 3.5 3.5 3.5 3.5 3.5 3.5
4 4 4 4 3.5 3.5 3.5
78013
CE
–
– 74492 74492
78058 78058 78058
– – –
– – –
74207
78013
–
–
78008
78013
CG
–
78010
78104
CH
–
–
–
–
–
78071
N/A
Fifth Wheel – models only – –
10, 15mm, 3/4”, 7/8”
1/2”
3.5 5
40
n 44574 AL,JR
10, 15mm, 3/4”, 7/8”
1/2”
3.5 5
40
21, 24mm, 11/16” 13/16”, 7/8”
15
– 16 35 –
11-12
n 96947 @
21, 24mm, 11/16” 13/16”, 7/8”
15
16 35 –
–
11-12
n 96947 @
21, 24mm, 11/16” 13/16”, 7/8”
15
16 35 –
–
06996
NO DRILL
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
3/4”, 1-1/8” NO DRILL
6
– –
74709
n 33094 AL,JR
n 44603 Ø,CP
– –
30 30 30 30 30 30 30
15 15 15 15 30
15
–
n 96947 @
19mm
OEM REPLACE.
FOOTNOTES
STANDARD WIRE
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
DRILL BITS 1/2”
40
–
Ø,HM
n 51169 Ø,HM
–
3.5 5
40
n 51102 AL,GP,JR Vibe All, Inc. GT Models
HG
1/2”
7/16”
n 06091 AL,GP 10, 15mm, 3/4”, 7/8”
78013
10, 15mm, 3/4”, 7/8”
–
n n n n
n 77040 AL,GP,JR
74207
n 33094 AL,JR
–
90-92 1993 94-96
Trans Sport Van All, Inc. Montana 97-98
40
78058
13mm, 9/16”, 11/16” 13mm, 9/16”, 11/16” 13mm, 9/16”, 11/16” 13mm, 9/16”, 11/16” 13mm, 9/16”, 11/16” 13mm, 9/16”, 11/16”
n 51163 GP,JR
1/2”
–
GP,JR
n 77049 GP,JR
–
40
13mm, 11/16”, 3/4” 7/16” 13mm, 11/16”, 3/4” 7/16”
03-05
–
1/2”
†,TA †,TA
Sunfire All Models
78058
40
11/16”, 3/8”, 1/2” 7/16” 11/16”, 3/8”, 1/2” 7/16”
n 77069 JR,KH
–
7/16”
HM,JR HM,JR,X
00-02
10, 15mm, 3/4”, 7/8” 9/16", 5/8”, 11/16” 14mm, 9/16”, 11/16” 14mm, 9/16”, 11/16”
30
7/16”
11/16”, 3/8”, 1/2” 7/16” 11/16”, 3/8”, 1/2” 7/16”
Sunfire All Models
10, 15mm, 3/4”, 7/8” 10, 15mm, 3/4”, 7/8” 10, 15mm, 3/4”, 7/8” 10, 15mm, 3/4”, 7/8”
3/8”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
35 35 40 40 30 30 40
Ø,HM,JR Ø,HM,JR,X
n 51163 GP,JR
9/16”, 11/16”, 7/8” 10, 15mm, 3/4”, 7/8”
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
10 20
–
–
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
APPLICATIONS GUIDE
n 51102 AL,GP,JR
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Le Mans Wagon
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
243
PONTIAC - RAM TRUCKS
PONTIAC - RAM TRUCKS
242
REESE TOWPOWER
05-06 99-02 2003 99-05
n 77134 Ø,JR
Astra 3 Dr. Hatchback Astra 5 Dr. Hatchback Aura Ion All, Except Redline & Models w/2.4 Liter Engine Ion 3 w/2.4 Liter Engine
08-09 08-09 07-09 03-07
n 77180 Ø,GP,JR n 77180 Ø,GP,JR
11/16”, 3/4”, 7/8” NO DRILL
25 25
n 77050 JR
3/4”
1/2”
35 25 25 25 25 35 35
Ion Redline L Series All Models L Series Wagon Only Outlook Relay All, Inc. AWD
05-07 04-06 00-02 03-04 07-09 05-07
14, 16, 17mm, 5/8” NO DRILL
77132 51164 77132 51164 77113 77113
HM,JR
3/4”
1/2”
HM,JR
3/4”
1/2”
HM,JR
3/4”
1/2”
HM,JR
3/4”
1/2”
TA
3/4”
1/2”
TA
3/4”
1/2”
n 06302 AL,GP,JR n 51102 AL,GP,JR
1/2”
11/16”, 3/4”
1/2”
14, 17mm, 11/16” NO DRILL
11/16”, 3/4”
10, 15mm, 3/4”, 7/8” 10, 15mm, 3/4”, 7/8”
91-95
SC Series 2 Dr. Coupe
96-02
Sky
07-08
Sky Redline
07-08
Sky
2009
Sky Redline
2009
SL Series 4 Dr. Sedan
91-02
SW Series Wagon
91-01
Vue All, Except Redline
02-07
n 06391 Ø,HM
18,19mm, 3/4”
Vue All, Inc. Redline
08-09
n 51185 Ø,HM n 06528 Ø,GP
tC tC tC xB xB xB xD
05-06 07-10 11-13 04-07 08-10 11-12 08-10
STERLING
Pickup, Bullet Full Size 4500 HD Chassis Cab
deep socket n 77014 HM,JR,KH,TA 13mm, 11/16” deep socket 11/16”, 3/8”, n 77206 Ø,HM,JR 1/2” 11/16”, 3/8”, n 77206 Ø,HM,JR 1/2” 11/16”, 3/8”, n 77206 HM,JR 1/2” 11/16”, 3/8”, n 77206 HM,JR 1/2” n 77014 HM,JR,KH,TA 13mm, 11/16” deep socket n 77014 HM,JR,KH,TA 13mm, 11/16” deep socket
n n n n n n n
77199 77199 77187 28501 77187 77187 77200
1/2”, 3/8”
45
1/2”
l 51083 Ø,GP,JR,RT 40 n 51079 AL,GP,JR
1/2”
40
18mm, 3/4” NO DRILL 10, 15mm, 3/4”, 7/8”
1/2”
5 5 25 3.5 5 40
l 44569 Ø,GP,JR n 33094 AL,JR n 44574 AL,JR
18mm, 3/4”
NO DRILL
10, 15mm, 3/4”, 7/8” 10, 15mm, 3/4”, 7/8”
1/2”
5 5 3.5 5
25 40
1/2”
3.5 5
40
OEM REPLACE.
FOOTNOTES
STANDARD WIRE
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
30 30 30
– – – –
78104 – 78104 78013
– – 74700 –
78104 78104 78013 78013
–
– – – –
–
78013
–
–
–
78013
–
–
– – 74711 85344
78013 78013 78104 78058
–
–
– – 85219 –
–
78104
–
–
– – – –
– – –
– –
– – – –
1/8”, 3/16”, 40 7/16”, 9/16” 1/8”, 3/16”, 40 7/16”, 9/16” 7/16” 35
–
78013
–
–
–
78104
–
–
7/16”
35
–
78104
–
–
7/16”
40
–
78104
–
–
7/16”
40
–
78104
–
–
1/8”, 3/16”, 40 7/16”, 9/16” 1/8”, 3/16”, 40 7/16”, 9/16”
–
78013
–
–
–
78013
–
–
GP
17mm, 11/16”
3/8”
GP
17mm, 11/16”
3/8”
Ø,GP
17, 19mm
NO DRILL
Ø,AG,JR
10mm, 14, 17mm NO DRILL
Ø,GP
17, 19mm
NO DRILL
Ø,GP
17, 19mm
NO DRILL
Ø,GP,JR
12, 13mm, 9/16”, NO DRILL 11/16”, 3/4”
NO DRILL
25 n 51193 Ø,HM
18,19mm, 3/4”
NO DRILL
18mm
NO DRILL
25 15
18,19mm, 3/4”
NO DRILL
3.5 4 30
n 44637 Ø,HM
18,19mm, 3/4” NO DRILL
3.5 4
30
74695
78013
BN,CG
–
n 44630 Ø,†,HM n 44580 Ø,GP
18,19mm, 3/4” NO DRILL 18mm
3.5 4 4 4
30 15
74720
78104
CH
–
– 85702 – 74691 78100 78010 –
78013 78104 78104 78013 78104 – 78013
–
–
– – – – – – –
–
–
–
–
–
–
NO DRILL
30 30 15 25 15 15 20
08-09
n 41936 @, †
3/4”
17/32”
12
n 96936 @ n 41940 @, †
3/4”
17/32”
12 15
30 16 35
15
16 35 –
15
16 35 –
n 96940 @ n 96947 @ 06996
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
DRILL BITS
11/16”, 3/4”
SC Series 2 Dr. Coupe
SCION
n 77014 HM,JR,KH,TA 13mm, 11/16”
WRENCHES
FOOTNOTES
n 06658 GP,JR,RB
n n n n n n
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
30 n 06135 JR n 06135 JR n 06136 Ø,TA
11/16”, 3/4”, 7/8” NO DRILL
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
21mm, 9/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8” 21, 24mm, 11/16” 13/16”, 7/8”
30 –
CG CG CG CH CH
–
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
245
APPLICATIONS GUIDE
9-2X Aero & Linear 9 - 3 All Styles 9 - 3 Convertible Only 9-5
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL SAAB
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
SATURN
APPLICATIONS GUIDE
REESE TOWPOWER
SAAB - STERLING
SAAB - STERLING
244
REESE TOWPOWER
08-09
n 44535 Ø,GP,JR n 44665 Ø,GP
09-13 93-01
n 77178 HM,JR n 77091 Ø,JR
Impreza Inc. Outback Sport & WRX, Except WRX STi Impreza 4 Dr. Sedan, Inc. WRX Impreza 5 Dr. Wagon, Inc. Outback Sport & WRX, Except WRX Sti & Quad Exhaust
02-07
n 77091 Ø,JR
08-11 08-12
n 77178 HM,JR n 77222 HM,JR
2012 08-12
n 77274 HM,JR n 77276 HM,JR n 77222 HM,JR
3/4” (2)
NO DRILL
20 n 06975 Ø,GP,JR n 51174 Ø,GP,JR
12mm, 14, 17mm NO DRILL 12mm, 14, 17mm NO DRILL
n 44607 HM,JR
17/32”
12 15
30 16 35
15
16 35 –
15
16 35 –
OEM REPLACE.
FOOTNOTES
STANDARD WIRE –
–
–
–
78064 78064 – 78064
78104 78104 78104 78104
CH
78092 –
78104 78104
–
– –
CH CH –
– – – –
NO DRILL
30
–
78104
–
–
10mm, 3/4”
1/2”, 3/8” 1/2”, 3/8”
35 45
78098 –
78104 78104
CH
3/4”
–
– –
45 30 45
–
78104
–
–
– –
78104 78104
– –
– –
3/4”
1/2”, 3/8”
10MM, 3/4”
1/2”, 3/8”
3/4”
1/2”, 3/8”
Legacy Sedan, Except Outback
05-07
n 06377 Ø,JR
12mm, 11/16”, 3/4”, 7/8” 14, 17mm, 3/4”
Legacy Sedan
08-09
n 51177 Ø,JR n 06377 Ø,JR
NO DRILL
10-13
n 51177 Ø,JR n 06669 JR,KH
14, 17mm, 3/4”
Legacy Sedan
10mm, 11/16”
All, Inc. Outback All, Except Outback Outback All, Except Outback
90-95 96-99 96-99 00-04
n n n n
Legacy Wagon All, Except Outback
05-07
n 06377 Ø,JR
Outback Sedan, Except Sport
00-04
n 51177 Ø,JR n 06287 Ø
Outback Sedan, Except Sport
05-07
n 06377 Ø,JR
Outback Wagon All, Except Sport
00-04
n 51177 Ø,JR n 06287 Ø
Outback Wagon All, Except Sport
05-07
n 06377 Ø,JR
Outback Wagon All, Except Sport
08-09
n n n n
06996
–
NO DRILL
n 06020 KH n 06287 Ø
10-13
21mm, 9/16” 13/16”, 7/8” 21mm, 9/16” 13/16”, 7/8” 21, 24mm, 11/16” 13/16”, 7/8”
–
14, 16, 17mm, 5/8”, 11/16” 14, 16, 17mm, 5/8”, 11/16”
06020 06020 06020 06287
51177 06377 51177 06669
NO DRILL
35
T-CONNECTOR
3/4”
–
35 30
10mm, 3/4”
3.5
WT. DISTRIB. INSTALL TIME
n 96936 @ n 41940 @, †
30 –
1/2”, 3/8”
90-99 00-04
Outback Wagon All, Except Sport
30 30
WT. CARRYING 12
10mm, 3/4”
Impreza 4 Dr. Sedan Impreza 5 Dr. Wagon, Inc. Sport & WRX, Except WRX Sti & Models w/Quad Exhaust Legacy Coupe & Sedan, Inc. Outback & SUS Legacy Sedan, Except Outback
Legacy Wagon Legacy Wagon Legacy Wagon Legacy Wagon
3.5 4 35 3.5 5.25 30
DRILL BITS 17/32”
CH
NO DRILL
25 20
NO DRILL
25
n 44581 Ø,JR
14, 17mm, 3/4”
NO DRILL
4
25
–
78104
–
–
14, 17mm, 3/4”
NO DRILL
14, 17mm, 3/4”
NO DRILL
25 25
n 44581 Ø,JR
14, 17mm, 3/4”
NO DRILL
4
25
–
78104
–
–
n 44631 JR,KH
10mm, 11/16” NO DRILL
4
45
85734
78104
CH
–
– – 78064 –
78104 78104 78104 78104
–
–
– – – –
78064
78104
CH
–
–
–
–
–
–
78104
–
–
78064
78104
CH
–
12mm, 3/4”, 7/8” 1/2”
KH
1-1/8 hole saw 12mm, 3/4”, 7/8” 1/2”
KH
12mm, 3/4”, 7/8” 1/2”
25 45 n 51204 HM,JR,KH
NO DRILL
25 25 25 20
NO DRILL
25
14, 17mm, 3/4”
NO DRILL
12mm, 11/16”, 3/4”, 7/8” 14, 17mm, 3/4”
NO DRILL
25 20
NO DRILL
25
14, 17mm, 3/4”
NO DRILL
12mm, 11/16”, 3/4”, 7/8” 14, 17mm, 3/4”
NO DRILL
25 20
NO DRILL
25
KH
12mm, 3/4”, 7/8” 1/2”
Ø
12mm, 11/16”, 3/4”, 7/8” 14, 17mm, 3/4”
Ø,JR
14, 17mm, 3/4”
Ø,JR
14, 17mm, 3/4”
Ø,JR
14, 17mm, 3/4”
JR,KH
10mm, 11/16”
25 25 NO DRILL 25 1-1/8 hole 45 n 51204 HM,JR,KH
10mm, 11/16”
1-1/8 Hole 4 Saw
–
45
n 44581 Ø,JR
n 44581 Ø,JR
14, 17mm, 3/4”
14, 17mm, 3/4”
NO DRILL
NO DRILL
4
4
25
25
– CH
n 44581 Ø,JR
14, 17mm, 3/4”
NO DRILL
4
25
78064
78104
CH
–
n 44581 Ø,JR
14, 17mm, 3/4” NO DRILL
4
25
78064
78104
CH
–
n 44631 JR,KH
10mm, 11/16” NO DRILL
4
45
78092
78104
CH
–
NO DRILL
NO DRILL
saw
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
10mm, 11/16”
1-1/8 Hole 4 Saw
–
45
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
247
APPLICATIONS GUIDE
Forester Impreza All, Inc. Outback Sport
n 77051 Ø
11/16”, 3/4” NO DRILL 11/16”, 7/8” NO DRILL
WRENCHES 3/4”
n 96947 @
06-10 11-12 03-06 98-08
FOOTNOTES
HITCH NUMBER
n 41936 @, †
n 96940 @
B9 Tribeca All Models B9 Tribeca All Models Baja Forester All, Inc. XT
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
Pickup, Bullet Full Size 5500 HD Chassis Cab
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
SUBARU
APPLICATIONS GUIDE
REESE TOWPOWER
STERLING - SUBARU
STERLING - SUBARU
246
REESE TOWPOWER
REESE TOWPOWER
19mm
NO DRILL
APPLICATIONS GUIDE
06-12 89-95 96-98
n 77140 Ø,EP n 77015 Ø,HM n 77015 Ø,HM
14mm, 18, 19mm NO DRILL
04-09 07-10
l 77097 – n 77189 HM,JR
3/4”, 7/8”
1/2”
11/16”, 3/4”
SX4 Sport Sedan
08-09
n 77190 HM,JR
11/16”, 3/4”
Vitara
99-05
n 77023 Ø,HM
19mm
1” Hole Cut Saw 1” Hole Cut Saw NO DRILL
19mm
NO DRILL
14mm, 18, 19mm NO DRILL
n 77015 Ø,HM,HP n 77023 Ø,HM
14mm, 18, 19mm NO DRILL 19mm
NO DRILL
TOYOTA
4Runner
07-09
Avalon
95-99
Avalon Avalon Avalon Camry 4 Dr. Sedan Camry 2 & 4 Dr. Camry 4 Dr. Camry 4 Dr. Camry 4 Dr. Camry 4 Dr., Except Hybrid Camry 4 Dr., Hybrid Camry 4 Dr., Except Hybrid
00-04 05-10 11-12 87-91 92-96 97-01 02-04
n 33038 Ø,HM
Ø,HM,JR
10,13,14mm
NO DRILL
EP
10mm, 19mm
NO DRILL
Ø,HM,JR
14, 17mm
NO DRILL
n 77035 Ø,HM,JR n 77035 Ø,HM,JR
05-06 07-09 07-09 10-11
06996
NO DRILL
17mm 17mm
NO DRILL NO DRILL
15
78058 78058
74896
78013
HG
– 78018
78013 78013
CG
– –
40
78101
78013
CG
–
74896
78013
HG
–
n 51152 Ø,HM
15 15, 18, 21mm, 9/16", 11/16", 3/4", T50
NO DRILL
3.5
15
n 33038 Ø,HM
06326 51178 06326 51178 06326 51178 06326 51178 06397 51190 06397 51190 06397 51190
3.5
15
74896
n 51152 Ø,HM
40 40 40 30 n n 15 n n 15 n n n n n n n n n n
14mm, 18mm NO DRILL
7/16", 1/2" 35
20 15 15, 18, 21mm, 9/16", 11/16", 3/4", T50
14mm, 18mm
NO DRILL
20
–
BN,RD,RZ, 85763 Fact Tow Package models only HG –
30 40
19mm
3.5 4
BN
OEM REPLACE.
85757 85763
FOOTNOTES
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
DRILL BITS
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE 3.5
30
HG
n 06326 HM n 51178 HM n 06025 – 10,13,14mm
8
78013 78013 78013
14, 18mm
NO DRILL
3.5
15
n 33038 Ø,HM
14mm, 18mm NO DRILL
3.5
15
7/16", 1/2" 35
18mm, 3/4”, 7/8” NO DRILL 18mm, 3/4”, 7/8” NO DRILL
30 30
n l l l
33023 33013 33013 44548
14, 17mm, 11/16” 1/2” 14, 17mm, 11/16” 1/2” 14,17mm, 11/16” 1/2”
HM
14, 17mm, 11/16” 1/2”
HM
14, 17mm, 11/16” 1/2”
HM
14, 17mm, 11/16” 1/2”
HM
14, 17mm, 11/16” 1/2”
HM
14, 17mm, 11/16” 1/2”
HM
14, 17mm, 11/16” 1/2”
HM
14, 17mm, 11/16” 1/2”
HM
14, 17mm, 11/16” 1/2”
GP,JR,TA
10, 12, 14, 17mm 1/2”
GP,JR,TA
10, 12, 14, 17mm 1/2”
GP,JR,TA
10, 12, 14, 17mm 1/2”
GP,JR,TA
10, 12, 14, 17mm 1/2”
GP,JR,TA
10, 12, 14, 17mm 1/2”
GP,JR,TA
10, 12, 14, 17mm 1/2”
15 15 20
15 15 15 15 15 15 15 15 45 45 45 45 45 45
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
18mm
CG HG
–
– – –
HG
– 74896 74896
78013 78013
– HG
– –
HG
NO DRILL
4
4
30
74709
78104
5 5 5 6
5 5.5 5.5 7.3
40 30 30 35
– 74663 74663 –
78104 78104 78104 78013
–
– – 85248 –
6
7.3 35
–
78013
–
–
–
78013
–
–
– – 78109 – –
78013 78013 78013 78104 78104
–
–
– – – – –
74205
78013
HG
–
85318
78013
HG
–
85318
78013
HG
–
85701
78104
CH
–
78109
78013
CH
–
78109
78013
CH
–
†
9/16”, 3/4”
1/2”
Ø
18mm, 3/4”
NO DRILL
Ø
18mm, 3/4”
NO DRILL
Ø,FE,LT,SI
10, 12, 13, NO DRILL 17mm, 3/4”, 1/2” 10, 12, 13, NO DRILL 17mm, 3/4”, 1/2”
l 44548 Ø,FE,LT,SI
Ø,HM,JR
14mm, 18mm NO DRILL
5
78018 – –
n 06098 – n 06098 –
77253 77253 77102 77004
NO DRILL
74896
n 44570 Ø,HM
n n l n
WRENCHES
FOOTNOTES
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
INSTALL TIME STYLE
STYLE
15
19mm
7/16", 1/2" 35
07-09
92-95 96-00 01-02 03-06
3.5
n 44543 Ø,EP
n 88001 –
4Runner 4Runner 4Runner 4Runner
NO DRILL
n 44526 Ø,GP
8 30
20 20 20
n 88001 – 96-98 01-06
15, 18, 21mm, 9/16", 11/16", 3/4", T50
14mm, 18mm
5
Factory Tow 74709 Package models only
– HG HG
– CH –
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
Grand Vitara Sidekick 2 & 4 Dr. Sidekick 2 & 4 Dr., Inc. JS 2WD, JX 4WD (Will Not Fit Sport Model) Swift+ 5 Dr. (Canada Only) SX4 Crossover
XL-7
DRILL BITS
n 51152 Ø,HM
15 n 88001 –
X-90 XL-7
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
n 77023 Ø,HM
NO DRILL
STANDARD WIRE
99-05
19mm
WIRING
Up to 2500 lb TW Up to 18000 lb GTW T-CONNECTOR
Grand Vitara
n 51147 Ø,GP
09-12
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW WT. CARRYING WT. DISTRIB. INSTALL TIME
Equator
YEAR
MODEL SUZUKI
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
249
SUZUKI - TOYOTA
SUZUKI - TOYOTA
248
REESE TOWPOWER
REESE TOWPOWER
Camry 4 Dr., Except Hybrid Camry Wagon, All Styles Celica All Models Corolla 2 & 4 Dr. Sedan Corolla 2 & 4 Dr. Sedan
2012 87-91 00-05 86-92 93-02
Corolla
2003
Corolla Corolla
Corolla Wagon 2 WD Corolla Wagon 4 WD Cressida Sedan Echo Echo All, Except Hatchback Echo All, Except Hatchback Echo Hatchback 2 & 4 Dr., Except Turbo (Canada Only) FJ Cruiser Highlander Highlander All, Inc. Hybrid Highlander All, Inc. Hybrid & models w/ Full Size 19” Spare Highlander All, Inc. Hybrid, except for w/ 19” spare Highlander All, Inc. Hybrid & models w/ Full Size 19” Spare Hilux LandCruiser LandCruiser LandCruiser
2008 09-13 88-92 88-93 86-92 00-02 00-02 03-05 04-05 07-12 01-03 04-07 08-11
n 77005 n n n n n n n n
77186 51171 77186 51171 77186 51171 77186 51171
10mm, 19mm
NO DRILL
14, 17mm
NO DRILL 1” hole saw
30
Ø,HM
NO DRILL
Ø,HM
17, 19mm
NO DRILL
20 20 20 20 20 20 20 20
Ø,HM
17, 19mm
NO DRILL
17, 19mm
NO DRILL
Ø,HM
17, 19mm
NO DRILL
Ø,HM
17, 19mm
NO DRILL
Ø,HM
17, 19mm
NO DRILL
Ø,HM
17, 19mm
NO DRILL
n 77086 Ø
17mm
n 77127 Ø,AD
14, 17mm
NO DRILL
NO DRILL
15
15 n 51087 Ø,GP 15 l 51153 Ø,HM l 51155 Ø,RT
44545 44076 33075 44670
78104 – 78013 78013 78013
78024
OEM REPLACE.
85701 – – – –
FOOTNOTES
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
78013
CH
–
CH
–
– – – – –
78013
CG
–
–
78013
–
–
–
78013
–
–
78020
78104
CH
–
– – – 78023 78023 – – 85701 74690 78062
78013 78013 78013 78013 78013 78013 78013 78013 78013 78013
–
CH
– – – – – – – – 85248 –
– – –
– – CG CG – –
Ø
14, 17mm
NO DRILL
Ø
14, 17mm
NO DRILL
Ø,HM,SV
10, 12, 14, 17mm
NO DRILL
n 44587 Ø,HM
10mm, 14, 17mm
NO DRILL
5
5
25
78067
78104
CH
–
12-13
l 44670 Ø,HM,SV
10, 12, 14, 17mm
NO DRILL
5
5
40
78067
78104
CH
–
08-12 91-95 96-97 98-99
17mm, 18mm NO DRILL
6 6 6
30 30 20
78013 78013 78013 78013
– – –
NO DRILL
5 5 5
85718 – 74208 74225
BN,HG
n 33066 Ø n 33066 Ø n 44546 Ø
BN,HG
LandCruiser
2000
n 44546 Ø
NO DRILL
5
6
20
–
78013
–
–
LandCruiser
01-02
n 44546 Ø
NO DRILL
5
6
20
85248
78013
–
85248
LandCruiser Matrix All Models
03-07 03-08
NO DRILL
5
6
20
– 78023
– 78013
– CG
– –
Matrix w/Ground Effects Matrix w/o Ground Effects Matrix All Models
03-08 03-08 09-12
78023 78023 78010
78013 78013 78104
CH
– – 74203
78013 78104
–
– –
85250 85250
78104
BN,HG
–
– 85725 85725
78013 78013 78013
MR2 Pickup All, Except T-100
Pickup All, Except T-100
Previa All, Inc. Supercharged Prius Prius Prius C
n 06276 Ø
14, 17mm
NO DRILL
n 51158 Ø,HM
08-12
NO DRILL NO DRILL
10mm, 14, 17mm
NO DRILL
5
5 25
Ø,GP
n 44546 Ø n 77183 Ø,HM,UD n 51169 Ø,HM,UD
n 77183 Ø,HM n 51169 Ø,HM
19mm
NO DRILL
19mm
NO DRILL
19mm
NO DRILL
19mm
NO DRILL
n 88001 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50
7/16", 1/2" 30
n 88001 –
15, 18, 21mm, 9/16", 11/16", 3/4", T50 14mm
7/16", 1/2" 30
n 06229 Ø,GP,JR
06996
10, 14, 17mm
NO DRILL
17, 19mm
NO DRILL
12, 13mm
NO DRILL
NO DRILL
17mm, 18mm NO DRILL 12, 19mm, 7/8” 12, 19mm, 7/8” 12, 19mm, 7/8” 12, 19mm, 7/8”
15 15
89-95
n 77179 Ø,HM,SC n 77236 Ø,HM,JR n 77277 Ø,GP
19mm, 3/4”
15 15
86-90 84-88
91-97 04-09 10-12 2012
14, 17mm 14, 17mm
n l l l
30 15 20 40
78109
5 6 3.5 3.5 5 5
19mm, 3/4” NO DRILL
5 6 30 3.5 15 3.5 20
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
45 45 40
40 15
10, 17, 18mm, 11/16” 17, 19mm
Ø,HM
INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
l 77102 EP n 77085 Ø
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
NO DRILL
n 51015 Ø,AA
3/4”, 7/8”
NO DRILL
3.5 4 20
n 33024 Ø,AA
3/4”, 9/16”
NO DRILL
5
5
60
n 51015 Ø,AA
3/4”, 7/8”
NO DRILL
3.5 4 20
n 33024 Ø,AA
3/4”, 9/16”
NO DRILL
5
5
60
30
30 25 20
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
CH BN,HG
CH BN,HG
CG CG
–
– – –
HG – CH CH
– – –
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
Corolla
04-07
n 06397 GP,JR,TA 10, 12, 14, 17mm 1/2” n 51190 GP,JR,TA 10, 12, 14, 17mm 1/2” n 06139 HM,JR,KH,SV 10, 12, 14, 17mm 1/2”, 1”
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
STANDARD WIRE
10-11
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
T-CONNECTOR
Camry 4 Dr., Hybrid
STYLE
YEAR
MODEL
APPLICATIONS GUIDE
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
251
TOYOTA
TOYOTA
250
REESE TOWPOWER
REESE TOWPOWER
03-07
Sequoia Sienna Van
08-12 98-00
n 06077 Ø
16mm, 7/8”
NO DRILL
15
n 44602 Ø,AI n 33008 –
Sienna Van
01-03
n 06077 Ø
16mm, 7/8”
NO DRILL
15
n 33008 –
Sienna Van All Models Sienna Van All Models
04-10 11-13
l 06141 Ø,HM,SV
10, 19mm, 6” NO DRILL Ratchet Extension
NO DRILL NO DRILL
15 15 n 06668 Ø,HM
17, 19mm
NO DRILL
20 n 51157 Ø,RT
l 51080 Ø,RT,JR 20 l 51080 Ø,RT,JR
l 06140 Ø,HM,SV Solara
99-03
Solara Solara T-100 Pickup All Models
04-06 07-09 93-98
Tacoma Pickup All, 2 & 4 WD (App. starts with 95-1/2)
95-04
n 77035 Ø,HM,JR
17mm
NO DRILL
15 n n n n
06326 51178 06387 06387
HM
10, 19mm, 6” NO DRILL Ratchet Extension 14, 17mm, 11/16” 1/2”
HM
14, 17mm, 11/16” 1/2”
Ø,JR
14, 17mm
NO DRILL
Ø,JR
14, 17mm
NO DRILL
3.5 4 20
Tercel 2 & 4 Dr. Sedan Tercel 2 & 4 Dr. Sedan Tundra
– –
19mm
NO DRILL
19mm
NO DRILL
3.5 5 30 3.5 5 30
l 33070 Ø,JR,TS l 33070 Ø,JR,TS
10, 19mm
NO DRILL
3.5 5 45
l 44648 Ø,HM,SV
3.5 5
30
–
78013
–
–
NO DRILL NO DRILL
3.5 5 3.5 5
30 30
78004 85720
78013 78104
–
19mm
CH
– –
10, 19mm, 6 ratchet
NO DRILL
3.5 5
45 85720
15 15 15 15
–
78013
–
–
78013 – 78013
– – BN,HG
– – –
n 33022 Ø,†,CN
CH
NO DRILL
5
7
45
– – 85718
NO DRILL
5
5.5 30
85250
78013
BN,HG
NO DRILL
5
5.5 40
05-08
n 51146 Ø,GP
10, 17, 19mm
NO DRILL
5
5.5 30
n 33090 Ø,GP
18mm, 9/16”, 7/32” Allen 18, 19mm, 9/16”, 3/4”, #45 Torx 18, 19mm, 9/16”, 3/4”, #45 Torx 10, 17, 19mm
NO DRILL
5
5.5 30
85718
78013
BN,HG
–
09-13
n 51146 Ø,GP
10, 17, 19mm
NO DRILL
5
5.5 30
n 33090 Ø,GP
10, 17, 19mm NO DRILL
5
5.5 30
85718
78013
BN,HG
–
74682 – – 74887
78058 78013 78013 78104
BO
85262 – – –
n 51108 Ø,GP
18,19mm, 3/4”, 7/8”
NO DRILL
5
5.5 40
n 33025 Ø
83-90 91-98 2000
77258
n 51047 Ø,GP
18mm, 7/8” NO DRILL
5
7.5 15
l 37069 –
9/16”, 3/4” 1/2”
5
7.5 35
33049 37034 37094 44054 33049 37034 37094 44054 33049 37034 37094 44054 44568
Ø
18mm, 3/4”
NO DRILL
07-09
n 51091 Ø,RT,CP,HM 17, 19, 22mm, NO DRILL
6
8 20
Ø,CP,HM
17, 19, 22mm, NO DRILL 3/4”, 7/8”
Tundra Models without Factory Installed Receiver
10-12
n 51091 Ø,RT,CP,HM 17, 19, 22mm, NO DRILL
6
8 20
n 44568 Ø,CP,HM
17, 19, 22mm, NO DRILL 3/4”, 7/8”
Yaris Liftback
HITCH NUMBER
1/2”
Tundra Models without Factory Installed Receiver
Venza, All Styles Yaris Sedan
–
–
20
n 51047 Ø,GP
01-02
l 37069 – Tundra
– – CH – w/ Fac- 85249 CG
CG
14, 17mm, 7/8” 14, 17mm, 7/8” 19mm
n l l n n l l n n l l n n
Tundra
OEM REPLACE.
–
20 20 20 25
FOOTNOTES
78113 78013
5
WT. DISTRIB. INSTALL TIME
– –
18mm, 7/8”, NO DRILL 3/4” 3/4” 1/2”
WT. CARRYING
6 10 40 3.5 5 30
n 44089 Ø
DRILL BITS
1/2”
17, 19mm
18mm, 7/8”, NO DRILL 3/4”
WRENCHES
78113
NO DRILL
Ø Ø
3.5 3.5 3.5 4 5 6.5
FOOTNOTES
–
NO DRILL NO DRILL
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE 6.5 25
tory Tow Package –
DRILL BITS
78013 78013 78104 78013
17, 19mm 17, 19mm
n 44051 Ø Tacoma Pickup All, Except X-Runner Tacoma Pickup All, Except X-Runner
78025 78026 78048 85249
Ø,RA Ø
n 51047 Ø,GP l 37069 –
03-06
09-13 07-11 07-11
18mm, 7/8” NO DRILL 9/16”, 3/4” 1/2” 18mm, 7/8” NO DRILL 9/16”, 3/4” 1/2”
3/4”, 7/8”
3/4”, 7/8”
l 06138 Ø n 77191 Ø,GP n 28502 Ø,†,AG,GP n 77191 Ø,GP 06996
12, 13mm
NO DRILL
12, 13mm
NO DRILL
12, 13mm
NO DRILL
17mm
NO DRILL
20
20 20 20
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
5 5 5 5
7.5 15 7.5 35 7.5 15 7.5 35
–
15/16", 3/4” 5/8”
–
15/16", 3/4” 5/8”
Ø
18mm, 7/8”
NO DRILL
Ø
18mm, 3/4”
NO DRILL
–
15/16", 3/4” 5/8”
–
15/16", 3/4” 5/8”
Ø
18mm, 7/8”
NO DRILL
Ø
18mm, 3/4”
NO DRILL
Ø
15/16", 3/4” 5/8”
–
15/16", 3/4” 5/8”
Ø
18mm, 7/8”
l 44604 Ø,HM,JR
17mm
NO DRILL
NO DRILL
5 7 7 5 5 7 7 5 5 7 7 5 6
7.5 12 12 7.5 7.5 12 12 7.5 7.5 12 12 7.5 8
20 30 30 20 20 30 30 20 20 30 30 20 20 n 41935 Ø,@,CP,HM, 17, 19mm, 21mm NO DRILL
6
8
3.5 4
74887 85247
– – BN,GC BN,GC
78104
85247
BN,GC
–
BN,GC
– –
78104 –
BO
– 85219
12
14 30 –
78058
–
–
n 96935 Ø,@,CP,HM 17, 19mm, 21mm NO DRILL 20 n 41935 Ø,@,CP,HM 17, 19, 21mm NO DRILL
12 12
14 30 14 30 –
78058
–
–
n 96935 Ø,@,CP,HM 17, 19, 21mm NO DRILL
12
14 30 BO
85219
†
20
–
74682 78071
78104 –
78108 85744
78104 78104
–
–
–
78013
–
–
5th-Wheel – Harness B –
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
l 51196 Ø,HM,SV
17mm,19mm NO DRILL
STANDARD WIRE
Sequoia
17, 19mm
WIRING
Up to 2500 lb TW Up to 18000 lb GTW T-CONNECTOR
96-00 01-05 06-12 01-02
WRENCHES
33060 33060 44540 44089
FOOTNOTES
HITCH NUMBER
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
n n n n
RAV4 RAV4 RAV4 Sequoia
17, 19mm
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
IONSTALL TIME STYLE
DRILL BITS
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
STYLE
n 77107 Ø n 77107 Ø
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL
APPLICATIONS GUIDE
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
253
TOYOTA
TOYOTA
252
REESE TOWPOWER
OEM REPLACE.
FOOTNOTES
STANDARD WIRE
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
WT. CARRYING
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
2005
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
n 77106 TA
DRILL BITS
2005
WRENCHES
1/2”
FOOTNOTES
3/4”, 7/8” 3/4”, 7/8”
STYLE
TA TA
WT. CARRYING WT. DISTRIB. INSTALL TIME
77197 77197 77197 77235 77235 77065 77106 77106
DRILL BITS
n n n n n n n n
WRENCHES
2006 07-09 07-09 10-12 10-12 94-98 99-04 99-04
FOOTNOTES
GTI 2 Dr. Hatchback GTI 2 Dr. Hatchback GTI 4 Dr. Hatchback GTI 4 Dr. Hatchback GTI 2 Dr. Hatchback Jetta Jetta III, Inc. GT Jetta Sedan, Except Gas Turbo & Wagon Models Jetta Sedan, Except Wagon Models (App. starts w/ 99-1/2) Jetta Sedan, Except Gas Turbo & Wagon Models (Old Body Style) Jetta Sedan, Except Wagon Models (Old Body Style) Jetta 4 Dr. Sedan (New Body Style)
HITCH NUMBER
77026 77106 77196 77026 77026 77197 77197 77197 77197 77235 77235 77249
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW INSTALL TIME STYLE
l n n l l n n n n n n n
DRILL BITS
07-10 07-09 07-12 85-06 99-06 10-13 10-13 10-13 10-13 2010 2010 10-12
WRENCHES
City Golf Canada Only City Jetta Sedan (Canada Only) Eos All Models Golf Golf Except GTI V6 Golf 2 Dr. Hatchback, Inc. TDI Golf 3 Dr. Hatchback, Inc. TDI (Canada Only) Golf 4 Dr. Hatchback, Inc. TDI Golf 5 Dr. Hatchback, Inc. TDI (Canada Only) Golf GTI 2 Dr. Hatchback (Canada Only) Golf GTI 4 Dr. Hatchback (Canada Only) Golf Wagon Canada Only
FOOTNOTES
77026 77026 77264 77266 77221
HITCH NUMBER
l l n n n
IONSTALL TIME STYLE
98-01 02-10 2012 2012 09-13
DRILL BITS
HITCH NUMBER
WRENCHES
STYLE
FOOTNOTES
YEAR
Beetle Beetle All, except Turbo S Beetle All, except Turbo Beetle, Turbo Only CC All, Except 4 Motion
MODEL VOLKSWAGEN
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW
HITCH NUMBER
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
30 30 20 30 35
– – – – –
78104 78104 – – –
30 30 40 30 30 15 15 15 15 40 40 40
– – – – –
78013 78013 78113 78013 78013
1/2”
15 15 15 40 40 30 30 30
– – – – – – – –
78104 78113 78113 78113 78113 78013 78013 78013
–
– – – – – – – –
3/4”, 7/8”
1/2”
30
–
78013
–
–
n 77106 TA
3/4”, 7/8”
1/2”
30
–
78013
–
–
05-10
n 77249 Ø,HM,JR,TA
40
85782
78104
CH
–
Jetta 4 Dr. Sedan (New Body Style)
11-13
n 77249 Ø,HM,JR,TA
40
–
–
–
–
Jetta SportWagen
09-13
n 77249 Ø,JR,TA
T-25, 10, 13mm, NO DRILL 11/16”, 3/4” T-25, 10, 13mm, NO DRILL 11/16”, 3/4” T-25, 10, 13mm, NO DRILL 11/16”, 3/4”
40
–
–
–
–
Jetta Wagon Passat All, Except 4 Motion & W8 Engine Models Passat All, Except 4 Motion
03-06 99-05
TA n – n 77039 RB,TA
–
06-10
n 77221 HM,JR,X
TA
13mm, 7/8”
1/2”
TA
13mm, 7/8”
1/2”
Ø,HM,JR
12mm, 11/16”
NO DRILL
GP,JR
13mm, 3/4”
11/16”
HM,JR,X TA
T-20, T-25, 13mm, 1/2” 11/16” 13mm, 7/8” 1/2”
TA
3/4”, 7/8”
Ø,GP,JR
13mm, 3/4”
NO DRILL
TA
13mm, 7/8”
1/2”
TA
13mm, 7/8”
1/2”
Ø,HM
13, 19mm, 3/4”
NO DRILL
Ø,HM
13, 19mm, 3/4”
NO DRILL
Ø,HM
13, 19mm, 3/4”
NO DRILL
Ø,HM
13, 19mm, 3/4”
NO DRILL
Ø,JR,KH
13, 18mm, 3/4”
NO DRILL
Ø,JR,KH
13, 18mm, 3/4”
NO DRILL
Ø,JR,TA Ø,HM
T-25, 10, 13mm, NO DRILL 11/16”, 3/4” 13, 19mm, 3/4” NO DRILL
Ø,HM
13, 19mm, 3/4”
07-10
Ø,HM
13, 19mm, 3/4”
NO DRILL
13, 18mm, 3/4”
NO DRILL
Ø,JR,KH
13, 18mm, 3/4”
NO DRILL
–
3/4”, 7/8”
1/2”
n 77221 HM,JR,X n 77155 †,HM,JR,X
Passat Sedan
12-13
Rabbit All Models Rabbit All Models Routan
2006 07-09 09-12
NO DRILL
Ø,JR,KH
n 77155 †,HM,JR,X Passat Wagon All, Except 4 Motion
1/2”
n 77267 Ø,EP,GP,
JR,SV,TA n 77197 Ø,HM n 77197 Ø,HM
09-13 04-10
06996
– – – – – – – –
– – – – – – –
– – – – – – – – – – – – – – – – –
T-25, T-27, 10mm, 3/4”
1/2”
50 40
– –
– 78013
–
– –
T-20, T-25, 13mm, 11/16” T-20, 13mm, 11/16” T-20, T-25, 13mm, 11/16” T-20, 13mm, 11/16” T-15, T-25, 10mm, 13mm, 3/4” 13, 19mm, 3/4”
1/2”
35
–
78113
–
–
1/2”
35
1/2”
35
85781
78113
CH
–
1/2”
35
NO DRILL
30
NO DRILL NO DRILL
15 15
78104 78113
–
13, 19mm, 3/4”
–
– – –
n 06550 Ø,GP,JR n 51192 Ø,GP,JR
13,15,18mm
NO DRILL
13,15,18mm
NO DRILL
20 20
n 06625 Ø,EP
17mm
NO DRILL
20
n 51203 Ø,GP,JR Tiguan Touareg
– –
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
13, 15, 18mm NO DRILL
4
4
n 44586 Ø,GP,JR
13,15,18mm NO DRILL
4
5
20
– – –
l 44611 Ø,EP n 44530 AA,RB
17mm
NO DRILL
18mm,T-25, T-27,7/8”
1/2”
3.5 6 6
20 90
85777 – 85733
20
BN, CH
78104 78113
– CH
– –
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
255
APPLICATIONS GUIDE
APPLICATIONS GUIDE
REESE TOWPOWER
VOLKSWAGON
VOLKSWAGON
254
REESE TOWPOWER
REESE TOWPOWER
140 160 240 740 760 780 850
n n n n n n n
850 Series Wagon
94-97
n 06024 GP,JR
940 Series, All Styles 960 Series, All Styles C30
91-95 92-94 08-10
n 06223 Ø,FE,JR n 06223 Ø,FE,JR
C70 Coupe
98-02
n 06024 GP,JR
C70 Convertible
98-04
n 06024 GP,JR
00-04 S40 Sedan Old Body Style 04-10 S40 Sedan New Body Style (App. starts with 2004-1/2) 01-09 S60 Sedan
n 77182 HM,JR,KH
n 77084 TA n 77156 Ø,GP,JR
3/4”
06426 06426 06426 06223 06223 06223 06024
3/4”, 7/8”
1/2” NO DRILL
OEM REPLACE.
FOOTNOTES
STANDARD WIRE
T-CONNECTOR
WT. DISTRIB. INSTALL TIME
WT. CARRYING
20
–
78104
–
–
NO DRILL NO DRILL
40 40
– – –
78104 78104 78113
–
8, 17, 19mm
– –
– – –
12, 14mm, 3/4”, 7/8” 12, 14mm, 3/4”, 7/8”
98-00
n 06024 GP,JR
V70 Wagon All, Inc. AWD & XC
01-02
n n n n
– – – – – – –
78013 78013 78013 78104 78104 78104 78104
–
– – – – – – –
– – – – – –
1/2”
20
–
78113
–
–
1/2”
20
–
78113
–
–
– –
– –
– –
– –
–
78104
–
–
–
78104
–
–
– 78012 – –
78104 78113 78104 78104
–
–
– – – –
20 25 17mm
NO DRILL
17mm
NO DRILL
12, 14mm, 3/4”, 7/8” 8, 17, 19mm
1/2” NO DRILL NO DRILL
15 15 20 40 35
20 25
06420 51172 06420 51172
DRILL BITS
1/2”
V70 Wagon All, Inc. AWD & XC
1/2” NO DRILL
WRENCHES
1/2”
n 06394 Ø,X n 06608 Ø,HM,JR,KH 13mm, 11/16” 3/4”, 7/8”
FOOTNOTES
12, 14mm, 3/4”, 7/8” 12, 14mm, 3/4”, 7/8” 8, 17, 19mm
NO DRILL NO DRILL
99-06 07-12 00-04 05-10
M10, M12, M13, 3/4”
HITCH NUMBER
WT. CARRYING WT. DISTRIB INSTALL TIME STYLE
DRILL BITS
GP,JR
14, 17, 22mm 8, 17, 19mm
S80 Sedan S80 Sedan V40 Wagon V50 Wagon
CH –
1/2”
20
–
78113
–
–
Ø,HM,JR
12, 14mm, 3/4”, 7/8” 17mm
NO DRILL NO DRILL
– – –
78113 78113 78113
–
17mm
15 15 15 15
–
Ø,HM,JR
– –
–
Ø,HM,JR
17mm
NO DRILL
Ø,HM,JR
17mm
NO DRILL
V70 Wagon All, Inc. AWD
08-10
n 44597 Ø,DU,EP,
XC60
10-13
n 44629 Ø,GP,JR,
XC70 Wagon AWD
03-07
GP,SQ
KH,SR
n 06420 Ø,HM,JR n 51172 Ø,HM,JR
17mm
NO DRILL
17mm
NO DRILL
8, 10, 13, NO DRILL 17mm, T-20 Torx 13mm, 11/16” NO DRILL
4
70
78005
78113
CH
–
4
4.5 45
85749
78113
CH
–
–
78113
–
–
70
–
78113
–
–
25 25
– 78047
78113 78113
– CH
– –
15 15
XC70 Wagon AWD
08-13
n 44597 Ø,DU,EP,
XC90 XC90
03-04 05-13
n 33073 Ø,JR n 33073 Ø,JR
GP,SQ
06996
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
WT. CARRYING WT. DISTRIB. INSTALL TIME
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
NO DRILL NO DRILL
FE Ø,FE,JR
98-00
03-07
INSTALL TIME STYLE
8, 17, 19mm 8, 17, 19mm
NO DRILL NO DRILL
n 06420 Ø,HM,JR n 51172 Ø,HM,JR n 06024 GP,JR
n 77084 TA n 77156 Ø,GP,JR
DRILL BITS
Ø,FE,JR Ø,FE,JR
14, 17, 22mm 14, 17, 22mm
3/8”, 1” Hole 45 Saw
M10, M12, M13, 3/4”
WIRING
Up to 2500 lb TW Up to 18000 lb GTW
60 60 60 40 40 40 20
FE FE
S70 Sedan Inc. AWD
V70 Wagon All, Inc. AWD
WRENCHES
FOOTNOTES
HITCH NUMBER
74-82 74-82 74-93 84-92 84-90 88-90 93-97
CLASS V
Up to 800 lb TW Up to 8000 lb GTW
Up to 500 lb TW Up to 5000 lb GTW
Look For Our Exclusive UPRATED Hitch Designs With Increased Tongue Weight.
8, 10, 13, 17mm, T-20 Torx 17, 18mm
NO DRILL
4
NO DRILL
17, 18mm
NO DRILL
5 5
5 5
IMPORTANT: Observe all safety precautions when working beneath a vehicle and eye wear protection.
FOOTNOTE ABBREVIATIONS ø No drilling required - use existing holes. n Square Tube hitch design. l Round Tube hitch design. @ Ultra Frame ball mount must be used to achieve maximum weight carrying rating. † Available while supply lasts. A 2 wire system. No Converter required, but a ModuLite® can be used. AA Requires temporary removal of bumper during installation. AC Hitch rated at 1,000 lbs. GTW, 100 lbs. TW. AG Drawbar Kit & Accessory Adapter sold separately. AI Additional installation time required. AL Additional installation time required for vehicles equipped with load leveling compressor. AM Not recommended on Trofeó models prior to 1989. 1989 units require minor fascia trim and exhaust repositioning. AO Will not fit vehicles with twin tailpipes. AY Does fit SE models with Sport Appearance Package, GT model or 4 Dr. STE. B 3 wire system. Requires Converter, but a ModuLite® can be used. BC Hitch rated at 1,500 lbs. GTW, 100 lbs. TW BF Requires standard bumper. Will not fit with step bumper. BN Exterior mounted plug on some or all models. May require an aftermarket electrical mounting box or bracket. (Sold separately) CA Models with dual exhaust require exhaust modification. CG T-One incorporates circuit protected taillight converter. CH T-One is equipped with circuit protected ModuLite® module. CK Drawbar installs though fascia on SC models. Obtain customer approval. CM OEM Style Attachments/Requires Factory Bumper For Hitch Installation. CN Requires OEM factory bumper for hitch installation. CP Fits All Models without Factory Installed Receiver. CQ Will not fit with heavy duty suspension. CS Will fit with full-size spare tire stowed under vehicle. CT Will not fit long bed models after 1999. CV Will not fit short wheel base with dual exhaust. D See auto dealer for trailer tow wiring kit. EB Factory electrical bracket will NOT fit with this hitch. Must use aftermarket electrical box or bracket. EF Fits all models with standard bumpers. EG Relocation of spare tire bracket is not required. NOTE: 19mm open end style wrench must be purchased to allow removal of spare tire after hitch installation. EP Fascia trimming required. F ModuLite® recommended. FE Fascia trimming required. Allow additional installation time. FM On vehicles equipped with load leveling device, air pump mounting modification required. FP Spare tire repositioning and/or modification of spare tire carrier may be required. FS Includes 2 & 4 WD models with heavy duty suspension. FT Models with 16" spare tire must be relocated. GC T-One is equipped with ModuLite® Lite module. GP Hitch crosstube concealed behind bumper. GU Will not fit vehicles with factory or aftermarket lower Fascia/Rollpan or Tube Bumper. H 3 wire system with OEM standard 2 wire harness. HB Slight fascia deformation may occur on some models. HD Will not fit 6 ft. bed pickups except 6 ft. Super Cab. HG T-One incorporates taillight converter. HJ Per Dodge owner's manual: If trailer is equipped with more than standard lighting (1 taillight per side), use of ModuLite® or dealer supplied harness is required. HM Hitch crosstube is visible beneath bumper. HX Minor exhaust modification may be required. HY Ultra Frame ball mount DT #4283/HH #80125 cannot be used in rise position on vehicles with step bumpers. JF Will not fit with 16" spare tire. JL Installation requires OEM bumper and brackets. JR Exhaust must be temporarily lowered for installation. JT 2WD models only. KA Gasoline engine models only. KH Minor heat shield modification may be required. KK When installing on a vehicle originally equipped with an OEM hitch, OEM bumper brackets must be purchased and installed prior to new hitch installation. KL Hitch is designed to attach beneath the OEM hitch. LA Optional Wider 1200mm Length Cross Bar. LB Optional Wider 1300mm Length Cross Bar. LS T-One incorporates low-side switching taillight converter. Additional installation time required. LT Requires removal of factory hitch if equipped. MB Will not fit models equipped with air suspension package. N DO NOT cut or splice vehicle wiring. Only use approved T-One or see auto dealer for trailer tow wiring kit. PA Will not fit 124" wheelbase or E-350 models. RD For vehicles equipped with factory tow package, may require additional components or may be used as a replacement harness. RI Cutting of rollpan in license plate area required for receiver tube access. Obtain customer approval first. RL Short box models require relocation of spare tire. RN Aftermarket spare tire repositioner may be used on 8 ft. bed models to ease installation of larger spare tires. RO Will not fit Silverado SS. SA Requires drilling on 6 ft. bed models. SB Will not fit models with short bed. SC Minor trimming of plastic trunk pan required. SD Hitches made before 07/21/06 are rated at 350/3500 WC. SH Hitches made before 09/27/07 are rated at 1200/12,000 WC & 1400/14,000 WD. SI Hitches made before 07/31/07 are rated at 350/3500 WC & 500/5000 WD. SP Hitches made before 04/27/08 are rated at 1200/12,000 WC & 1400/14,000 WD. SS Hitches made before 03/31/08 are rated at 1000/10,000 WC & 1200/12,000 WD. SV Trimming or removal of under body appearance panel required. TA Trunk access required for hitch installation. TF For 3/4 and 1 ton vehicles only. TH Will not fit models with skid shield. VB Will not fit vehicles with vibration damper installed at rear of frame on drivers side.
APPLICATIONS GUIDE
Series Series Series Series, All Styles Series, All Styles Series 2 Dr. Coupe Series Sedan, Inc. T5
CLASS III/IV
CLASS III
Up to 300 lb TW Up to 3500 lb GTW IONSTALL TIME STYLE
DRILL BITS
WRENCHES
FOOTNOTES
HITCH NUMBER
STYLE
YEAR
MODEL VOLVO
APPLICATIONS GUIDE
CLASS II
CLASS I
Up to 200 lb TW Up to 2000 lb GTW
257
VOLVO
VOLVO
256