75cm 4m. It s pretty easy to work it out. All of our Bathroom Wall Cladding measures the same:

THERE ARE THREE MAIN FITTING METHODS... A THERE ARE THREE MA B IN FITTING METHODS ... Intro Your bathroom cladding is easy to cut and slot tog...
Author: Alyson Bryant
34 downloads 0 Views 701KB Size
THERE ARE THREE MAIN FITTING METHODS...

A

THERE ARE

THREE MA

B

IN FITTING

METHODS ...

Intro Your bathroom cladding is easy to cut and slot together. With the addition of some trims for joints and corners, you can easily create a stylish look. You will need the following tools: Tape measure a Fine tooh saw a Spirit level a Pencil a Adhesive or screws a DIY Knife a Clear Silicone if installing behind a shower a

HOW MANY PACKS DO YOU NEED? How many will I need?

2m 75cm 3m

4m

It’s pretty easy to work it out. All of our Bathroom Wall Cladding measures the same: Length: 2.6measy to work it out… It’s pretty Width: 25cm

All of our Bathroom Thickness: 8mm Wall Cladding measures the same: Length: 2.6m The length Width: 25cmof 2.6m will be sufficient to cover the height of most bathroom walls. Thickness: The width8mm of 25cm means that 4 panels equals 1m in width. So, if the area you’re looking to

decorate is 2m wide, you will need 8 panels.

The length of 2.6m will be sufficient to cover the height of most bathroom walls. The width of 25cm means that each pack of cladding equals 1m in with. So, if the area you’re looking to decorate is 2m wide, youofwill need The combined widths the walls2 packs. to be decorated above are 795cm. This is just under 8m.

Remember, each pack of cladding is 1m (4 x 25cm) in width, so you will need to purchase 32

The combined widths of the walls to be decorated above are 795cm. This is just under 8m. panels of cladding. height ofis the bathroom 2m, meaning 2.6m lengths will coverofthis. Remember, each packThe of cladding 1m (4 x 25cm) iniswidth, so you willour need to purchase 8 packs cladding. The height of the bathroom is 2m, meaning our 2.6m lengths will cover this.

THERE ARE THREE MAIN FITTING METHODS...

Installation methods A) SCREWS B) NAILS/STAPLES C) ADHESIVE

THERE ARE THREE MAIN FITTING METHODS...

A

B

C

Bathroom cladding can be glued directly to the wall or on timber battons. Look at each wall separately.

A) Screws

If the wall is relatively flat and in good condition you can glue directly to the wall. Nails or staples will also help.

B) Nails or Staples

If the wall is in poor condition and/or not flat, it may be better to fit timber battons to the wall first.

C) Decorating Glue

Battons should be screwed to the wall horizontally at 40cm intervals. Cladding can then be glued/ screwed/nailed or stapled where it meets the batton. Battons should always be installed perpendicular to the intended direction of the cladding panels.

THERE ARE THREE MAIN FITTING METHODS...

How does it fit together?

FITTING YOUR CLADDING... FITTING The panels slot YOUR together likeCLADDING... laminate flooring.

The

If installing behind a shower, it will be necessary to run a bead of clear silicone down the groove of each panel before you insert the tongue of the next panel. Be sure to clean off any excess panels slot together like laminate flooring... silicone as you install. This will ensure thatlaminate no shower water finds its way though the joints. Also be The panels slot together like flooring... sure to seal the bottom where it meets with the bath/shower cubicle/tiles.

run silicone bead down this groove if installing behind a shower

groove slots into next panel

THERE ARE THREE MAIN FITTING METHODS...

Decide where will be best to start For best results work from left to right installing panels with the groove to the left and the tongue to the right. Ensure that you will not be left with a thin cutting at the opposite end of the wall before you fix any panels (remember that each panel is 25cm wide). Install a corner strip of your choice if you are using corner trims (see corners without trims below for alternative). The cladding panel will slot into the corner trim (be sure to slot the groove side of the panel into the trim leaving the tongue side ready for the next panel). Straighten the panel with a spirit level and fix into place. Remember to apply adhesive to the back when you are ready to go. If using adhesive it is still advisable to pin or staple into place while the adhesive is setting. Pins/staples/screws should be fitted into the tongue of each panel before the next panel is slotted into place (See below).

THERE ARE THREE MAIN FITTING METHODS...

A

B

C

Continue to the end of the wall ensuring that you install another corner trim with the last panel. The last panel may need to be cut to size. Measure the size required and cut down the length of the panel. Remember that you can cut a little shorter as the corner strip will hide the edge.

A) Screws

For best results you should remove any bathroom fittings and fixtures before installation and re-fit after installation of your cladding. In some instances this may not be practical so you will need to cut panels accordingly as you progress with installation.

B) Nails or Staples

C) Decorating Glue

Corners without trims

It is possible to install panels without corner trims. However, this will require silicone adhesive and a higher level of DIY skill. When fitting the perpendicular panel you will need to cut off the groove edge. Using a DIY knife, cut the back skin of the panel 10mm shorter, remove any vertical fins if necessary. The edge of the panel into the corner should now be just the surface skin of the cladding which will curve into the corner when pressure is applied. Silicone should be applied to the back edge of the 10mm strip. Push into place an apply fixings in the usual way. Be sure to clean off any excess silicone as you go.

THERE ARE THREE MAIN FITTING METHODS...

Trim types A) COVING - takes all the effort out of those wall/ceiling junctures and looks stylish. B) INFILL STRIPS - comes in chrome and gold and can be used horizontally or vertically. Slots between panels to give a 5mm coloured stripe between panels. Works particularly well on ceilings to give a paneled effect.

A

B

THERE ARE THREE MAIN FITTING METHODS...

C) INTERNAL CORNER - takes all the effort out of 90 degree joints and can add decorative flair with a chrome effect.

C

THERE ARE THREE MAIN FITTING METHODS...

D) EXTERNAL CORNER - takes all the effort out of 90 degree joints and can add decorative flair with a chrome effect.

D

THERE ARE THREE MAIN FITTING METHODS...

E) END CAP TRIM - can be used to finish your cladding if only decorating part of a wall. It can also be used horizontally if you are only cladding part way up the wall (as a splashback behind a sink for example). Also used if your wall has a natural/flush edge (for example, a wall that ends at a doorway without a frame).

E

Maintenance Your bathroom cladding requires very little maintenance. Use a lint free cloth with warm water and a small amount of detergent to wipe down your cladding. No abrasives.

Got a question? We’ll be happy to answer any of your DIY cladding questions. Simply send us an email to [email protected] and we’ll get back to you within 24 hours (usually same day if before 3pm). Thank you for using Bathroom Cladding Direct.

THERE ARE THREE MAIN FITTING METHODS...