5W AC-DC Power-Supply PAC5B ● ● ● ● ●

85 … 264 VAC / 100 … 400 VDC universal input Continuously short circuit and over current protected Isolation class II MTBF > 300000 hours Small outlines

Model guide Type PAC5B03S PAC5B05S PAC5B09S PAC5B12S PAC5B15S PAC5B24S

Output voltage Output current range Ripple & noise up to Efficiency typ.@ full 20 MHz load, Vin 230 VAC Accuracy min. max. [mVp-p] max. [%] typ. [VDC] [%] [mA] [mA] 3.3 ±3 100 1000 150 65 5.0 ±2 100 1000 150 70 9.0 ±2 56 560 150 72 12 ±2 42 420 150 74 15 ±2 34 340 150 75 24 ±2 21 210 150 75

Capacitive load [µF] max. 2200 1500 680 470 330 100

Specifications Input Voltage range Frequency Full load input current Inrush current Standby power Recommended fuse Hold up time Isolation Isolation voltage (input to output) Isolation resistance Leakage current Output Minimum load Line regulation Load regulation @ 10 to 100% load change Temperature coefficient

EMI

85..264 VAC or 100..400 VDC Power derating see diagram 47 .. 440 Hz 200 mA max @ 115 VAC 100 mA max @ 230 VAC 20 A @ 115 VAC 30 A @ 230 VAC 0.5 W, max. 1 A / 250 V slow blow 20 ms min. @ 115 VAC 80 ms min. @ 230 VAC 3000 VAC (1 minute, 300000 h ~100 kHz -40 °C to +85 °C (with derating, see diagram) see diagram -40 °C to +105 °C 100 °C, max. 85 %, max. Free air convection EN60950, UL60950 42 x 27 x 11 mm 10 g UL94V-0 On PCB Wave 265 °C max., 10 s max. Manual 370 °C max., 5 s max.

EN55022 (CISPR22), class A (External circuit refer to fig. 2) EN55022 (CISPR22), class B (External circuit refer to fig. 3) EN55022 (CISPR22), class B (External circuit refer to fig. 2 and 3) IEC, EN61000-4-2, contact ± 4 kV perf. criteria B IEC, EN61000-4-3, 10 V/m perf. criteria A (External circuit refer to fig. 3) IEC, EN61000-4-4, ± 2 kV, perf. criteria B (External circuit refer to fig. 2) IEC, EN61000-4-4, ± 4 kV, perf. criteria B (External circuit refer to fig. 3) IEC, EN61000-4-5, ± 1 kV perf. criteria B (External circuit refer to fig. 3) IEC, EN61000-4-5, ± 2 kV perf. criteria B (External circuit refer to fig. 3) IEC, EN61000-4-6, 3 Vrms perf. criteria A (External circuit refer to fig. 3) IEC, EN61000-4-8, 10 A/m perf. criteria A IEC, EN61000-4-11, 0…70 % perf. criteria B

1. External electrolytic capacitors are required to models. More details refer to typical applications. 2. Ripple and noise were measured refer to “ripple and noise measure configuration”. 3. All specifications were measured at Ta 25 °C, humidity