INSTRUCTION MANUAL

CS511 Dissolved Oxygen Probe Revision: 2/16

C o p y r i g h t © 2 0 0 1 - 2 0 1 6 C a m p b e l l S c i e n t i f i c , I n c .

Limited Warranty “Products manufactured by CSI are warranted by CSI to be free from defects in materials and workmanship under normal use and service for twelve months from the date of shipment unless otherwise specified in the corresponding product manual. (Product manuals are available for review online at www.campbellsci.com.) Products not manufactured by CSI, but that are resold by CSI, are warranted only to the limits extended by the original manufacturer. Batteries, fine-wire thermocouples, desiccant, and other consumables have no warranty. CSI’s obligation under this warranty is limited to repairing or replacing (at CSI’s option) defective Products, which shall be the sole and exclusive remedy under this warranty. The Customer assumes all costs of removing, reinstalling, and shipping defective Products to CSI. CSI will return such Products by surface carrier prepaid within the continental United States of America. To all other locations, CSI will return such Products best way CIP (port of entry) per Incoterms ® 2010. This warranty shall not apply to any Products which have been subjected to modification, misuse, neglect, improper service, accidents of nature, or shipping damage. This warranty is in lieu of all other warranties, expressed or implied. The warranty for installation services performed by CSI such as programming to customer specifications, electrical connections to Products manufactured by CSI, and Product specific training, is part of CSI's product warranty. CSI EXPRESSLY DISCLAIMS AND EXCLUDES ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. CSI hereby disclaims, to the fullest extent allowed by applicable law, any and all warranties and conditions with respect to the Products, whether express, implied or statutory, other than those expressly provided herein.”

Assistance Products may not be returned without prior authorization. The following contact information is for US and international customers residing in countries served by Campbell Scientific, Inc. directly. Affiliate companies handle repairs for customers within their territories. Please visit www.campbellsci.com to determine which Campbell Scientific company serves your country. To obtain a Returned Materials Authorization (RMA), contact CAMPBELL SCIENTIFIC, INC., phone (435) 227-9000. After an application engineer determines the nature of the problem, an RMA number will be issued. Please write this number clearly on the outside of the shipping container. Campbell Scientific’s shipping address is: CAMPBELL SCIENTIFIC, INC. RMA#_____ 815 West 1800 North Logan, Utah 84321-1784 For all returns, the customer must fill out a “Statement of Product Cleanliness and Decontamination” form and comply with the requirements specified in it. The form is available from our website at www.campbellsci.com/repair. A completed form must be either emailed to [email protected] or faxed to (435) 227-9106. Campbell Scientific is unable to process any returns until we receive this form. If the form is not received within three days of product receipt or is incomplete, the product will be returned to the customer at the customer’s expense. Campbell Scientific reserves the right to refuse service on products that were exposed to contaminants that may cause health or safety concerns for our employees.

Safety DANGER — MANY HAZARDS ARE ASSOCIATED WITH INSTALLING, USING, MAINTAINING, AND WORKING ON OR AROUND TRIPODS, TOWERS, AND ANY ATTACHMENTS TO TRIPODS AND TOWERS SUCH AS SENSORS, CROSSARMS, ENCLOSURES, ANTENNAS, ETC. FAILURE TO PROPERLY AND COMPLETELY ASSEMBLE, INSTALL, OPERATE, USE, AND MAINTAIN TRIPODS, TOWERS, AND ATTACHMENTS, AND FAILURE TO HEED WARNINGS, INCREASES THE RISK OF DEATH, ACCIDENT, SERIOUS INJURY, PROPERTY DAMAGE, AND PRODUCT FAILURE. TAKE ALL REASONABLE PRECAUTIONS TO AVOID THESE HAZARDS. CHECK WITH YOUR ORGANIZATION'S SAFETY COORDINATOR (OR POLICY) FOR PROCEDURES AND REQUIRED PROTECTIVE EQUIPMENT PRIOR TO PERFORMING ANY WORK.

Use tripods, towers, and attachments to tripods and towers only for purposes for which they are designed. Do not exceed design limits. Be familiar and comply with all instructions provided in product manuals. Manuals are available at www.campbellsci.com or by telephoning (435) 227-9000 (USA). You are responsible for conformance with governing codes and regulations, including safety regulations, and the integrity and location of structures or land to which towers, tripods, and any attachments are attached. Installation sites should be evaluated and approved by a qualified engineer. If questions or concerns arise regarding installation, use, or maintenance of tripods, towers, attachments, or electrical connections, consult with a licensed and qualified engineer or electrician. General • Prior to performing site or installation work, obtain required approvals and permits. Comply with all governing structure-height regulations, such as those of the FAA in the USA. • Use only qualified personnel for installation, use, and maintenance of tripods and towers, and any attachments to tripods and towers. The use of licensed and qualified contractors is highly recommended. • Read all applicable instructions carefully and understand procedures thoroughly before beginning work. • Wear a hardhat and eye protection, and take other appropriate safety precautions while working on or around tripods and towers. • Do not climb tripods or towers at any time, and prohibit climbing by other persons. Take reasonable precautions to secure tripod and tower sites from trespassers. • Use only manufacturer recommended parts, materials, and tools. Utility and Electrical • You can be killed or sustain serious bodily injury if the tripod, tower, or attachments you are installing, constructing, using, or maintaining, or a tool, stake, or anchor, come in contact with overhead or underground utility lines. • Maintain a distance of at least one-and-one-half times structure height, 20 feet, or the distance required by applicable law, whichever is greater, between overhead utility lines and the structure (tripod, tower, attachments, or tools). • Prior to performing site or installation work, inform all utility companies and have all underground utilities marked. • Comply with all electrical codes. Electrical equipment and related grounding devices should be installed by a licensed and qualified electrician. Elevated Work and Weather • Exercise extreme caution when performing elevated work. • Use appropriate equipment and safety practices. • During installation and maintenance, keep tower and tripod sites clear of un-trained or nonessential personnel. Take precautions to prevent elevated tools and objects from dropping. • Do not perform any work in inclement weather, including wind, rain, snow, lightning, etc. Maintenance • Periodically (at least yearly) check for wear and damage, including corrosion, stress cracks, frayed cables, loose cable clamps, cable tightness, etc. and take necessary corrective actions. • Periodically (at least yearly) check electrical ground connections. WHILE EVERY ATTEMPT IS MADE TO EMBODY THE HIGHEST DEGREE OF SAFETY IN ALL CAMPBELL SCIENTIFIC PRODUCTS, THE CUSTOMER ASSUMES ALL RISK FROM ANY INJURY RESULTING FROM IMPROPER INSTALLATION, USE, OR MAINTENANCE OF TRIPODS, TOWERS, OR ATTACHMENTS TO TRIPODS AND TOWERS SUCH AS SENSORS, CROSSARMS, ENCLOSURES, ANTENNAS, ETC.

Table of Contents PDF viewers: These page numbers refer to the printed version of this document. Use the PDF reader bookmarks tab for links to specific sections.

1. Introduction ................................................................ 1 2. Precautions ................................................................ 2 3. Initial Inspection ......................................................... 2 3.1

Shipping Kit and Accessories .............................................................. 2 3.1.1 Shipping Kit .................................................................................. 2 3.1.2 Optional Probe Accessories .......................................................... 2

4. QuickStart ................................................................... 3 5. Overview ..................................................................... 5 6. Specifications............................................................. 6 7. Installation .................................................................. 8 7.1 7.2 7.3 7.4 7.5

Getting Probe Ready to Use ................................................................. 8 Mount Probe....................................................................................... 10 Wiring to the Datalogger.................................................................... 10 Programming...................................................................................... 11 Calibration.......................................................................................... 11

8. Maintenance ............................................................. 13 8.1

Cleaning Probe and Replacing the Membrane ................................... 13

Appendices A. Importing Short Cut Code Into CRBasic Editor ... A-1 B. Example Programs................................................. B-1 B.1 B.2

VoltDiff CR1000 Example .............................................................. B-1 VoltSE CR200(X) Program ............................................................. B-2

C. Dissolved Oxygen Tables ...................................... C-1 C.1 C.2

Dissolved Oxygen in Fresh Water ................................................... C-1 Dissolved Oxygen in Salt Water ...................................................... C-2

D. Sensorex’s Model DO6200/T ................................. D-1 D.1 D.2

DO6200/T Specifications ................................................................ D-1 Accessories for DO6200/T.............................................................. D-2

i

Table of Contents

E. PT4-L Agitator ........................................................ E-1 E.1 E.2 E.3

Description ....................................................................................... E-1 PT4-L Specifications ........................................................................ E-2 Agitator Control ............................................................................... E-2

1-1.

The CS511 is currently Sensorex’s DO6400/T (left). The DO6200/T (right) was shipped prior to June 2008 (Appendix D). .. 1 Separate the lower body from the upper body ................................... 13 Remove membrane and O-ring ......................................................... 14 Using a toothbrush to clean probe ..................................................... 15 Proper O-ring placement ................................................................... 16 Installing membrane .......................................................................... 17 Check for leakage .............................................................................. 18 Sensorex’s model DO6200/T .......................................................... D-1 Preventing Bio-fouling of a DO Sensor ........................................... E-1 DO sensor with PT4 Agitator ........................................................... E-2 Agitator Wiring ................................................................................ E-3

Figures 8-1. 8-2. 8-3. 8-4. 8-5. 8-6. D-1. E-1. E-2. E-3.

Tables 7-1. 7-2. B-1. B-2.

Wire Color, Function, and Datalogger Connection for Differential Measurements............................................................. 10 Wire Color, Function, and Datalogger Connection for SingleEnded Measurements ..................................................................... 11 Wiring for CR1000 Example .......................................................... B-1 Wiring for CR200(X) Example ....................................................... B-2

CRBasic Examples B-1. B-2.

VoltDiff CR1000 Example .............................................................. B-1 VoltSE CR200(X) Program............................................................. B-2

ii

CS511 Dissolved Oxygen Probe 1.

Introduction The CS511 is a rugged, low-maintenance sensor that is manufactured by Sensorex. It consists of a self-polarizing galvanic cell that generates a millivolt signal proportional to the amount of oxygen present in the measured medium (typically water). NOTE

This manual provides information only for CRBasic dataloggers. It is also compatible with many of our retired Edlog dataloggers. For Edlog datalogger support, see an older manual at www.campbellsci.com\old-manuals or contact a Campbell Scientific application engineer for assistance.

NOTE

Currently, the CS511 is Sensorex’s Model DO6400/T. Prior to June 2008, the CS511 was Sensorex’s Model DO6200/T. Programming, wiring, and most specifications are the same for these two sensors. However, they use different accessories and look different (see FIGURE 1-1). Refer to Appendix D, Sensorex’s Model DO6200/T (p. D-1), if you have Sensorex’s Model DO6200/T.

DO6400/T

DO6200/T

FIGURE 1-1. The CS511 is currently Sensorex’s DO6400/T (left). The DO6200/T (right) was shipped prior to June 2008 (Appendix D).

1

CS511 Dissolved Oxygen Probe

2.

3.

Precautions •

READ AND UNDERSTAND the Safety section at the front of this manual.

•

The CS511 is a precision instrument. Please handle it with care.

•

Because the CS511 is shipped dry, electrolyte needs to be added before using the probe (Section 7.1, Getting Probe Ready to Use (p. 8)).

•

Letting the CS511 dry up shortens the life of the membrane and probe.

•

Drain the solution from the CS511 before storing it out of water.

•

Replace the membrane and recalibrate the probe before redeploying the CS511 after it has been stored out of water or dried up in the field.

Initial Inspection

3.1

•

Upon receipt of the CS511, inspect the packaging and contents for damage. File damage claims with the shipping company.

•

Immediately check package contents against the shipping documentation (see Section 3.1, Shipping Kit and Accessories (p. 2)). Contact Campbell Scientific about any discrepancies.

•

The model number and cable length are printed on a label at the connection end of the cable. Check this information against the shipping documents to ensure the expected product and cable length are received.

Shipping Kit and Accessories NOTE

Except for the agitator, these items are for Sensorex’s DO6400/T. Refer to Appendix D, Sensorex’s Model DO6200/T (p. D-1), if you have a DO6200/T.

3.1.1 Shipping Kit (1) Membrane replacement tool (1) Bottled DO electrolyte, 250 ml (2) Teflon membranes (2) Membrane O-rings (2) Membrane spaces

3.1.2 Optional Probe Accessories

2

•

PT4-L Agitator with Repeat Cycle Timer for stagnant conditions (see Appendix E, PT4-L Agitator (p. E-1))

•

22261 Maintenance Kit containing (5) Teflon membranes, (5) membrane O-rings, (5) tensioning washers, and a 250-ml bottle of electrolyte

•

22262 Maintenance Kit containing (25) Teflon membranes, (25) membrane O-rings, (25) tensioning washers, and a 500-ml bottle of electrolyte

CS511 Dissolved Oxygen Probe •

4.

22263 Spare Parts Kit containing (2) membrane locks, (2) tensioning washers, (2) body O-rings, and (1) membrane-replacement tool

QuickStart Short Cut is an easy way to program your datalogger to measure the sensor and assign datalogger wiring terminals. Short Cut is available as a download on www.campbellsci.com and the ResourceDVD. It is included in installations of LoggerNet, PC200W, PC400, or RTDAQ. The following procedure shows using Short Cut to program the CS511. 1.

Open Short Cut and. Click New Program.

3

CS511 Dissolved Oxygen Probe

2.

Select Datalogger Model and Scan Interval (default of 5 s is alright for most applications). Click Next.

3.

Under the Available Sensors and Devices list, select the Sensors | Water | Quality folder. Select CS511 Dissolved Oxygen Probe, and click to move the selection to the Selected device window. Variables default to DOmv for the millivolt measurements and DOppm for the ppm values. The default calibration value of 0.34 is based on an average. It is preferable to calibrate the probe using the procedure provided in Section 7.5, Calibration (p. 11).

4

CS511 Dissolved Oxygen Probe

5.

4.

After selecting the sensor and offset calculation, click Wiring Diagram to see how the sensor is to be wired to the datalogger. The wiring diagram can be printed now or after more sensors are added.

5.

Select any other sensors you have, then finish the remaining Short Cut steps to complete the program. The remaining steps are outlined in Short Cut Help, which is accessed by clicking on Help | Contents | Programming Steps.

6.

If LoggerNet, PC400, or PC200W is running on your PC, and the PC to datalogger connection is active, you can click Finish in Short Cut and you will be prompted to send the program just created to the datalogger.

7.

If the sensor is connected to the datalogger, as shown in the wiring diagram in step 4, check the output of the sensor in the datalogger support software data display to make sure it is making reasonable measurements.

Overview The CS511 is a galvanic probe which produces a millivolt signal proportional to the amount of oxygen present in the measured medium. Oxygen diffuses through the membrane onto the cathode, reacts chemically, and combines with the anode. An electrical current is produced by this chemical reaction which is converted from microamps to millivolts by an in-line resistor. An in-line thermistor also conditions the signal providing automatic temperature compensation. With these features, the probe produces a linear, millivolt output proportional to the oxygen present in the medium in which it is placed. The probe consists of two parts, an upper part with cathode, anode, and cable, and a lower part comprising of a screw-on membrane cap. The probe is shipped dry, but has a membrane installed in the cap. With the membrane in place, the cap must be filled with electrolyte solution before the cap is screwed onto the top component. The probe is self-polarizing and requires no external power source.

5

CS511 Dissolved Oxygen Probe

The probe’s robust construction and simple design make maintenance and servicing it straightforward. There is no need to send the probe back to the factory for servicing. It uses a strong, easy-to-clean, and easy-to-change membrane in a screw-on membrane cap. Regular servicing is not required. The probe can be fully overhauled in five minutes. The CS511 has a user-specified cable length. Its cable can terminate in:

6.

•

Pigtails that connect directly to a Campbell Scientific datalogger (option –PT).

•

Connector that attaches to a prewired enclosure (option –PW). Refer to www.campbellsci.com/prewired-enclosures for more information.

•

Connector that attaches to a CWS900 Wireless Sensor Interface (option –CWS). The CWS900 allows the probe to be used in a wireless sensor network. Refer to www.campbellsci.com/cws900 for more information.

Specifications Features: • • •

6

In-line thermistor provides automatic temperature compensation Agitator available that keeps the probe clean and moves water across membrane for more accurate readings Compatible with the following CRBasic dataloggers: CR200(X), CR6, CR800, CR850, CR1000, CR3000, CR5000, and CR9000(X)

Principle of Measurement:

Membrane-covered, galvanic oxygen probe

Output Signal:

33 mV ± 9 mV (100% saturation), < 2 mV (0% saturation)

Accuracy:

Better than ± 2% of reading ± 1 digit when calibration temperature equals measuring temperature ± 5 °C

Response Time:

5 min. from 100% to 0% oxygen

Materials of Construction Body: Anode: Cathode:

Noryl Zinc Silver

Diameter:

5.72 cm (2.25 in)

Height:

17.78 cm (7 in) from bottom of sensor to end of cable-strain relief

Shipping Weight

0.8 kg (1.75 lb)

Cable Jacket Material:

PVC

CS511 Dissolved Oxygen Probe

Operating Conditions Temperature: Pressure: Minimum Submersion Depth: Minimum Water Flow:

0 to 50 °C (32 to 122 °F) 0 to 100 psig 60 mm (2.5 in) 5 cm/s (2 inch/s) across membrane

Calibration:

In air or in air saturated water

Temperature Compensation:

Automatic from 4 to 40 °C (40 to 104 °F)

Range of Dissolved Oxygen:

0.5 to 50 ppm

Probe Electrolyte:

NaCl + glycerol (prevents freezing)

7

CS511 Dissolved Oxygen Probe

7.

Installation If you are programming your datalogger with Short Cut, skip Section 7.3, Wiring to the Datalogger (p. 10), and Section 7.4, Programming (p. 11). Short Cut does this work for you. See Section 4, QuickStart (p. 3), for a Short Cut tutorial.

7.1

8

Getting Probe Ready to Use 1.

Unscrew the lower body from the upper body.

2.

Inspect the membrane for wrinkles. Replace membrane if wrinkled (see Section 8.1, Cleaning Probe and Replacing the Membrane (p. 13)).

CS511 Dissolved Oxygen Probe

NOTE

3.

Pour clean water into the lower body and look for leakage around the membrane. Dispose of the water, and if there is leakage, replace membrane (see Section 8.1, Cleaning Probe and Replacing the Membrane (p. 13)).

4.

Pour fresh electrolyte in the bottom cap and fill to the top of the cap.

5.

Keep the probe upright with the cable pointed upwards (not sideways). Screw the bottom cap onto the upper body until hand tight.

Excess electrolyte will leak out at the joint between the probe’s cap and upper body.

9

CS511 Dissolved Oxygen Probe

7.2

Mount Probe Mount the CS511 in water at a slight angle, which prevents bubbles from becoming trapped on the membrane.

7.3

Wiring to the Datalogger The CS511 can use one differential channel (TABLE 7-1) or one single-ended channel (TABLE 7-2). Differential wiring is better at rejecting electrical noise and ground loop error. TABLE 7-1. Wire Color, Function, and Datalogger Connection for Differential Measurements Wire Color

Wire Function

Datalogger Connection Terminal

Signal High

U configured for differential input , DIFF H (differential high, analog-voltage input)

Black

Signal Reference

U configured for differential input1, DIFF L (differential low, analog-voltage input)

Clear

Shield

AG or ⏚ (analog ground)

1

White

1

U channels are automatically configured by the measurement instruction.

10

CS511 Dissolved Oxygen Probe

TABLE 7-2. Wire Color, Function, and Datalogger Connection for Single-Ended Measurements Wire Color

Wire Function

Datalogger Connection Terminal

White

Signal

U configured for single-ended analog 1 input , SE (single-ended, analog-voltage input)

Black

Signal Reference

AG or ⏚ (analog ground)

Clear

Shield

AG or ⏚ (analog ground)

1

U channels are automatically configured by the measurement instruction.

7.4

Programming Short Cut is the best source for up-to-date datalogger programming code. Programming code is needed when: • •

Creating a program for a new datalogger installation Adding sensors to an existing datalogger program

If your data acquisition requirements are simple, you can probably create and maintain a datalogger program exclusively with Short Cut. If your data acquisition needs are more complex, the files that Short Cut creates are a great source for programming code to start a new program or add to an existing custom program. NOTE

Short Cut cannot edit programs after they are imported and edited in CRBasic Editor. A Short Cut tutorial is available in Section 4, QuickStart (p. 3). If you wish to import Short Cut code into CRBasic Editor to create or add to a customized program, follow the procedure in Appendix A, Importing Short Cut Code Into CRBasic Editor (p. A-1). Programming basics for CRBasic dataloggers are provided below. Complete program examples for select dataloggers can be found in Appendix B, Example Programs (p. B-1). The VoltDiff() or VoltSE() can be used to measure the CS511. In the CR200(X)-series dataloggers, only the VoltSE() instruction can be used since these dataloggers do not support differential measurements.

7.5

Calibration The multiplier is used to calibrate the CS511 probe. To calculate the multiplier: 1.

Program the datalogger using a multiplier of one (see Section 4, QuickStart (p. 3), or Section 7.4, Programming (p. 11)).

2.

Wire the CS511 to the datalogger (see wiring diagram generated by Short Cut or Section 7.3, Wiring to the Datalogger (p. 10)).

3.

If the CS511 has been deployed in the field, gently wipe the membrane with a soft cloth.

11

CS511 Dissolved Oxygen Probe

4.

Place the CS511 in air away from direct sunlight with the membrane facing upward.

5.

Place a drop of clean water on the membrane.

6.

Wait for readings to stabilize. This may take 15 minutes or more.

7.

Determine the air temperature and barometric pressure.

8.

Using a calibration chart such as that provided in Appendix C, Dissolved Oxygen Tables (p. C-1), determine the oxygen concentration of the air.

9.

Use the following equation to calculate the multiplier: M = P/R where: M = Multiplier P = Concentration in PPM of the air (from the calibration chart) R = The signal output of the probe when using a multiplier of one

10. Change the multiplier in the datalogger program from one to the calculated number (see Section 4, QuickStart (p. 3)), or Section 7.4, Programming (p. 11)). Instead of step 10, the multiplier can be entered using a separate instruction in the program. This will allow a new multiplier to be added to the program without rewriting, compiling, and downloading the program to the datalogger. For this method, CRBasic dataloggers can use the following expression. The multiplier value is entered into the expression through the Public Table using the numeric display in PC200W, LoggerNet, PC400, PConnect, PConnectCE, or datalogger keyboard display. CRBasic Expression for Entering Multiplier: DOppm = DOMult * DOmV

12

CS511 Dissolved Oxygen Probe

8.

Maintenance The only maintenance required is regular cleaning and replacement of the membrane.

8.1

Cleaning Probe and Replacing the Membrane 1.

Unscrew the lower body from the upper body (FIGURE 8-1).

FIGURE 8-1. Separate the lower body from the upper body 2.

Safely dispose of the electrolyte. Make sure the cap’s O-ring does not fall out of the cap.

13

CS511 Dissolved Oxygen Probe

3.

Using the membrane tool, unscrew the membrane lock that is in the lower body (see FIGURE 8-2).

4.

Remove and dispose of the membrane and its O-ring as show in FIGURE 8-2.

Membrane Tool

Membrane Lock

Spacer Membrane Membrane O-ring Cap O-ring

FIGURE 8-2. Remove membrane and O-ring

14

CS511 Dissolved Oxygen Probe

5.

To clean, immerse the top part of the sensor in distilled white vinegar (3% acetic acid) for about 30 min. If vinegar is unavailable, use a soft toothbrush, automatic dishwasher detergent, and clean water to clean the cathode, anode, and plastic. Rinse all components thoroughly with clean water after cleaning (see FIGURE 8-3).

FIGURE 8-3. Using a toothbrush to clean probe

15

CS511 Dissolved Oxygen Probe

6.

Replace the membrane and its O-ring by first placing the new O-ring at the very bottom of the membrane cavity (see FIGURE 8-4). Remove the paper backing from a new membrane and place the new membrane on top of the O-ring, and then place the spacer on top of the membrane. Using the membrane tool, install the membrane lock on top of the spacer as shown in FIGURE 8-5. Make sure the cap is upright (not sideways) when securing the membrane lock to the spacer.

FIGURE 8-4. Proper O-ring placement

16

CS511 Dissolved Oxygen Probe

Membrane Tool

Membrane Lock

Spacer Membrane O-ring

FIGURE 8-5. Installing membrane 7.

Inspect the membrane for wrinkles; replace membrane if wrinkled.

17

CS511 Dissolved Oxygen Probe

8.

Pour some clean water into the lower body and look for leakage around the membrane (see FIGURE 8-6); replace membrane if there is leakage. If there is no leakage, dispose of the water.

FIGURE 8-6. Check for leakage 9.

Pour fresh electrolyte in the bottom cap and fill to the top of the cap.

10. Keep the sensor upright so that the cable is pointed upwards (not sideways). Screw the bottom cap onto the upper body until hand tight. NOTE

18

Excess electrolyte will leak out at the joint between the sensor’s cap and upper body.

Appendix A. Importing Short Cut Code Into CRBasic Editor This tutorial shows: •

How to import a Short Cut program into a program editor for additional refinement

•

How to import a wiring diagram from Short Cut into the comments of a custom program

Short Cut creates files, which can be imported into CRBasic Editor. Assuming defaults were used when Short Cut was installed, these files reside in the C:\campbellsci\SCWin folder: • • • • • • • •

.DEF (wiring and memory usage information) .CR6 (CR6 datalogger code) .CR2 (CR200(X) datalogger code) .CR1 (CR1000 datalogger code) .CR8 (CR800 or CR850 datalogger code) .CR3 (CR3000 datalogger code) .CR5 (CR5000 datalogger code) .CR9 (CR9000(X) datalogger code)

Use the following procedure to import Short Cut code and wiring diagram into CRBasic Editor.

NOTE

1.

Create the Short Cut program following the procedure in Section 4, QuickStart (p. 3). Finish the program and exit Short Cut. Make note of the file name used when saving the Short Cut program.

2.

Open CRBasic Editor.

3.

Click File | Open. Assuming the default paths were used when Short Cut was installed, navigate to C:\CampbellSci\SCWin folder. The file of interest has the .CR6, .CR2, .CR1, .CR8, .CR3, .CR5, or .CR9 extension. Select the file and click Open.

4.

Immediately save the file in a folder different from C:\Campbellsci\SCWin, or save the file with a different file name.

Once the file is edited with CRBasic Editor, Short Cut can no longer be used to edit the datalogger program. Change the name of the program file or move it, or Short Cut may overwrite it next time it is used. 5.

The program can now be edited, saved, and sent to the datalogger.

6.

Import wiring information to the program by opening the associated .DEF file. Copy and paste the section beginning with heading “-Wiring for CRXXX–” into the CRBasic program, usually at the head of the file. After pasting, edit the information such that an apostrophe (') begins each line. This character instructs the datalogger compiler to ignore the line when compiling.

A-1

Appendix A. Importing Short Cut Code Into CRBasic Editor

A-2

Appendix B. Example Programs B.1 VoltDiff CR1000 Example Programming for the CR800, CR850, CR3000, and CR5000 is similar to this CR1000 program. TABLE B-1 shows the wiring for the example. TABLE B-1. Wiring for CR1000 Example CR1000 Connection

Sensor Wire

1H

White

1L

Black

Ground

Clear

CRBasic Example B-1. VoltDiff CR1000 Example 'CR1000 'Declare Variables and Units Public Batt_Volt Public DOmV Public DOppm Units Batt_Volt=Volts Units DOmV=mV Units DOppm=ppm 'Define Data Tables DataTable(Table1,True,-1) DataInterval(0,60,Min,10) Sample(1,DOmV,FP2) Sample(1,DOppm,FP2) Sample(1,Batt_Volt,FP2) EndTable DataTable(Table2,True,-1) DataInterval(0,1440,Min,10) Minimum(1,Batt_Volt,FP2,False,False) EndTable 'Main Program BeginProg Scan(5,Sec,1,0) 'Default Datalogger Battery Voltage measurement Batt_Volt: Battery(Batt_Volt) 'CS511 Dissolved Oxygen Probe measurements DOmV and DOppm: VoltDiff(DOmV,1,mV250,1,True,0,_60Hz,1,0) DOppm=DOmV*0.34 'Call Data Tables and Store Data CallTable(Table1) CallTable(Table2) NextScan EndProg

B-1

Appendix B. Example Programs

B.2 VoltSE CR200(X) Program The CR200(X)-series must use the VoltSE() instruction since these dataloggers do not make differential measurements. If the other CRBasic dataloggers use the VoltSE() instruction instead of the VoltDiff() instruction, their programming will be similar to this example. TABLE B-2 shows the wiring for the example. TABLE B-2. Wiring for CR200(X) Example CR200(X) Connection

Sensor Wire

SE1

White

Ground

Black

Ground

Clear

CRBasic Example B-2. VoltSE CR200(X) Program 'CR200(X) Series 'Declare Variables and Units Public Batt_Volt Public DOmV Public DOppm Units Batt_Volt=Volts Units DOmV=mV Units DOppm=ppm 'Define Data Tables DataTable(Table1,True,-1) DataInterval(0,60,Min) Sample(1,DOmV) EndTable DataTable(Table2,True,-1) DataInterval(0,1440,Min) Minimum(1,Batt_Volt,False,False) EndTable 'Main Program BeginProg Scan(10,Sec) 'Default Datalogger Battery Voltage measurement Batt_Volt: Battery(Batt_Volt) 'CS511 Dissolved Oxygen Probe measurements DOmV and DOppm: VoltSE(DOmV,1,1,1,0) DOppm=DOmV*0.34 'Call Data Tables and Store Data CallTable(Table1) CallTable(Table2) NextScan EndProg

B-2

Appendix C. Dissolved Oxygen Tables C.1 Dissolved Oxygen in Fresh Water

C-1

Appendix C. Dissolved Oxygen Tables

C.2 Dissolved Oxygen in Salt Water

C-2

Appendix D. Sensorex’s Model DO6200/T Prior to June 2008, Campbell Scientific’s CS511 was Sensorex’s model DO6200/T (see FIGURE D-1) instead of Sensorex’s model DO6400/T. Programming, wiring, and some specifications are the same for these two sensors. However, they look different and use different accessories.

FIGURE D-1. Sensorex’s model DO6200/T

D.1 DO6200/T Specifications Principle of Measurement:

Membrane covered, galvanic oxygen probe

Output Signal:

1.65 mV ±0.45 mV per mg/l

Accuracy:

Better than ± 2 % of reading ± 1 digit when calibration temperature equals measuring temperature ± 5 °C

Output Impedance:

10 kΩ nominal

Response Time:

After equilibration, 2 min. for 90% of final value

D-1

Appendix D. Sensorex’s Model DO6200/T

Materials of Construction Probe body: O-rings: Membrane:

Delrin Membrane O-ring = Buna N Body Seal O-ring = Viton 0.05 mm Teflon

Dimensions and Weight:

8.9 cm (3.5 in) height, 5.6 cm (2.2 in) diameter, 0.5 kg (1.1 lb)

Cable Length:

3 m (10 ft)

Cable Description:

5-wire, 22 AWG-shielded, PVC jacketed

Operating Conditions Temperature: Pressure: Minimum Submersion Depth: Minimum Water Flow:

0 to 50 °C (32 to 122 °F) Maximum 10 atmospheres (147 psig) 60 mm (2.5 in) 5 cm/s (2 in/sec) across membrane

Calibration:

In air or in air saturated water

Temperature Compensation:

Automatic from 4 to 40 °C (40 to 104 °F)

Range of Dissolved Oxygen:

0 to 20 mg/l, 0 to 200 % saturated

Electrode Materials:

Ag cathode/Zn anode

Probe Electrolyte:

NaCl

D.2 Accessories for DO6200/T 14054 Teflon Membrane for DO6200/T (Qty 5) 14053 Teflon Membrane for DO6200/T (Qty 25) 14056 Membrane Replacement Tool for DO6200/T 14055 DO Electrolyte for DO6200/T, 500 ml

D-2

Appendix E. PT4-L Agitator E.1 Description The PT4 agitator is a reliable, robust agitator for use in conjunction with probes subjected to bio-fouling in ponds and stagnant water conditions (flow