Applicator LV 227 Manual P/N 405030_05 - English Edition 06/14

NORDSON BENELUX  MAASTRICHT  THE NETHERLANDS

Order number P/N = Order number for Nordson articles

Note This is a Nordson corporation publication which is protected by copyright. Copyright  1997. No part of this document may be photocopied, reproduced or translated to another language without the prior written consent of Nordson Corporation. The information contained in this publication is subject to change without notice. © 2014 All rights reserved. - Translation of Original Trademarks AccuJet, AeroCharge, Allegro, Apogee, AquaGuard, Artiste, Asymtek, Automove, Autotech, Baitgun, Blue Box, BM-32, BM-58, BM-63, Bowtie, Build‐A‐Part, CanWorks, Century, CF, CleanSleeve, CleanSpray, Color‐on‐Demand, ColorMax, Control Coat, Coolwave, Cross‐Cut, CrystallCut, cScan+, Dage, Dispensejet, DispenseMate, DuraBlue, DuraDrum, Durafiber, DuraPail, Dura‐Screen, Durasystem, Easy Coat, Easymelt, Easymove Plus, Ecodry, Econo‐Coat, e.dot, EFD, Eliminator, Emerald, Encore, Equatherm, ESP, e-stylized, ETI‐stylized, Excel 2000, Fibrijet, Fillmaster, FlexiCoat, Flexi‐Spray, Flex‐O‐Coat, Flow Sentry, Fluidmove, FoamMelt, FoamMelt - stylized, FoamMix, F.R. Gross, Freedom, Fulfill, GreenUV, HDLV, Heli‐flow, Helix, Horizon, Hot Shot, iControl, iDry, iFlow, Isocoil, Isocore, Iso‐Flo, iTRAX, JR, KB30, Kinetix, KISS, Lean Cell, Little Squirt, LogiComm, Magnastatic, March, Maverick, MEG, Meltex, MicroCoat, MicroMark, Micromedics, Micro‐Meter, MicroSet, Microshot, Millenium, MiniBlue, Mini Squirt, Moist‐Cure, Mountaingate, MultiScan, NexJet, No‐Drip, Nordson, Nordson - stylized, Nordson and Arc, nXheat, Optimum, Package of Values, Paragon, PatternView, PermaFlo, PICO, PicoDot, Plasmod, PluraFoam, Poly-Check, Porous Coat, PowderGrid, Powderware, Precisecoat, PRIMARC, Printplus, Prism, ProBlue, Prodigy, Pro‐Flo, Program‐A‐Bead, Program‐A‐Shot, Program‐A‐Stream, Program‐A‐Swirl, ProLink, Pro‐Meter, Pro‐Stream, Pulsar, Quantum, RBX, Rhino, Saturn, Saturn with rings, Scoreguard, SC5, S. design stylized, Seal Sentry, Sealant Equipment & Engineering, Inc., SEE and design, See‐Flow, Select Charge, Select Coat, Select Cure, Servo‐Flo, Shot‐A‐Matic, Signature, Signature - stylized, Slautterback, Smart‐Coat, Smart‐Gun, Solder Plus, Spectrum, Speed‐Coat, Spirex, Spraymelt, Spray Squirt, StediFlo, Stratablend, Super Squirt, SureBead, Sure Clean, Sure Coat, Sure‐Max, SureWrap, TAH, Tela‐Therm, Tip‐Seal, Tracking Plus, TRAK, Trends, Tribomatic, Trilogy, TrueBlue, TrueCoat, Tubesetter, Ultra, UniScan, UpTime, U‐TAH, Value Plastics, Vantage, Veritec, VersaBlue, Versa‐Coat, VersaDrum, VersaPail, Versa‐Screen, Versa‐Spray, VP Quick Fit, VP Quick-Fit stylized, VP stylized, Walcom, Watermark, When you expect more., X‐Plane, Xaloy, Xaloy - stylized, YesTech are registered trademarks of Nordson Corporation. Accubar, Active Nozzle, Advanced Plasma Systems, AeroDeck, AeroWash, AltaBlue, AltaSlot, Alta Spray, AquaCure, ATS, Auto‐Flo, AutoScan, Axiom, Best Choice, BetterBook, Blue Series, Bravura, CanNeck, CanPro, Celero, Chameleon, Champion, Check Mate, ClassicBlue, Classic IX, Clean Coat, Cobalt, Concert, ContourCoat, Controlled Fiberization, Control Weave, CPX, cSelect, Cyclo‐Kinetic, DispensLink, DropCure, Dry Cure, DuraBraid, DuraCoat, e.dot+, E‐Nordson, Easy Clean, EasyOn, EasyPW, Eclipse, Equalizer, Equi=Bead, Exchange Plus, FillEasy, Fill Sentry, FlexSeam, Flow Coat, Fluxplus, G‐Net, G‐Site, Genius, Get Green With Blue, Gluie, Ink‐Dot, IntelliJet, iON, Iso‐Flex, iTrend, KVLP, Lacquer Cure, Maxima, Mesa, MicroFin, MicroMax, Mikros, MiniEdge, Minimeter, MiniPUR, MonoCure, Multifil, MultiScan, Myritex, Nano, OmniScan, OptiMix, OptiStroke, Optix, Origin, Partnership+Plus, PatternJet, PatternPro, PCI, PharmaLok, Pinnacle, PluraMix, Powder Pilot, Powder Port, Powercure, Process Sentry, Pulse Spray, PURBlue, PURJet, PurTech, Quad Cure, Ready Coat, RediCoat, RollVIA, Royal Blue, Select Series, Sensomatic, Shaftshield, SheetAire, Smart, Smartfil, SolidBlue, Spectral, Spectronic, SpeedKing, Spray Works, StediTherm, Summit, Sure Brand, SureFoam, SureMix, SureSeal, Swirl Coat, Tempus, ThruWave, TinyCure, Trade Plus, Trio, FruFlow, Ultra FoamMix, UltraMax, Ultrasaver, Ultrasmart, Universal, ValueMate, Versa, VersaPUR, Viper, Vista, Web Cure, 2 Rings (design) are trademarks of Nordson Corporation.

Windows is a registered trademark of Microsoft Corporation.

P/N 405030_05

LV 227 Edition 06/14

2014 Nordson Corporation

Declaration of Conformity Guidelines: 2006/42/EG 2006/95/EG 97/23/EG Product group:  Pneumatic applicator for cold glue Model number:  LV227 Part number(s):       

372843 372844 372845 372846 372847 372848 7302265

     

372849 372850 372851 372852 372853 372854

     

373381 373382 373383 373384 373385 373386

     

377805 377806 377807 377808 377809 377810

International standards fulfilled:  NEN-EN-ISO 12100-1:2003  NEN-EN-ISO 12100-2:2003  EN 60204-1 I hereby take sole responsibility for the declaration that the above product to which this declaration refers fulfills all of the standards and guidelines stated above. Declared by:

- German -

Paul Spronck CEO Maastricht, March 21, 2011

NORDSON BENELUX B.V. Bergerstraat 10, 6226BD Maastricht, Netherlands

Declaration of Conformity Guidelines: 2006/42/EG 2006/95/EG 97/23/EG

Product group:  Pneumatic applicator for cold glue Model number:  LV227C Part number(s):  373915  7301726

 373916  7301729

 373917

 373918

International standards fulfilled:  NEN-EN-ISO 12100-1:2003  NEN-EN-ISO 12100-2:2003  EN 60204-1

I hereby take sole responsibility for the declaration that the above product to which this declaration refers fulfills all of the standards and guidelines stated above. Declared by:

Paul Spronck CEO

- English -

Maastricht, March 21, 2011

NORDSON BENELUX B.V. Bergerstraat 10, 6226BD Maastricht, Netherlands

Table of Contents

I

Table of Contents

 2014 Nordson Corporation

Nordson International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Distributors in Eastern & Southern Europe . . . . . . . . . . . . . . . . . Outside Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Africa / Middle East . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Asia / Australia / Latin America . . . . . . . . . . . . . . . . . . . . . . . . . . China . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

O‐1 O‐1 O‐1 O‐2 O‐2 O‐2 O‐2 O‐2 O‐2

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Alert Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Responsibilities of the Equipment Owner . . . . . . . . . . . . . . . . . . . . Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Instructions, Requirements, and Standards . . . . . . . . . . . . . . . . User Qualifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Applicable Industry Safety Practices . . . . . . . . . . . . . . . . . . . . . . . . Intended Use of the Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . Instructions and Safety Messages . . . . . . . . . . . . . . . . . . . . . . . Installation Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maintenance and Repair Practices . . . . . . . . . . . . . . . . . . . . . . . Equipment Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Equipment Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Relieving System Hydraulic Pressure . . . . . . . . . . . . . . . . . . De‐energizing the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disabling the Applicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Safety Warnings and Cautions . . . . . . . . . . . . . . . . . . . Other Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . First Aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1‐1 1‐1 1‐2 1‐2 1‐2 1‐3 1‐3 1‐3 1‐4 1‐4 1‐4 1‐5 1‐5 1‐6 1‐6 1‐6 1‐6 1‐7 1‐10 1‐10

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Updated Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Intermittent Adhesive Application . . . . . . . . . . . . . . . . . . . . . . . . . . .

2‐1 2‐1 2‐1 2‐1 2‐2 2‐2 2‐2

LV 227 Edition 06/14

P/N 405030_05

II

Table of Contents

P/N 405030_05

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing Applicator in Machines . . . . . . . . . . . . . . . . . . . . . . . . . . . Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting the Solenoid Valve . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting Control Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting the Material Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjusting the adhesive quantity / stem stroke . . . . . . . . . . . . . .

3‐1 3‐1 3‐2 3‐2 3‐2 3‐2 3‐2 3‐2

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Adhesive Processing Instructions . . . . . . . . . . . . . . . . . . . Compatibility of Different Types of Adhesive . . . . . . . . . . . . . . . . . Emergency Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Initial Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Daily Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Daily Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4‐1 4‐1 4‐1 4‐2 4‐2 4‐2 4‐2

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disassembling an Applicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disassembling in the Case of Solidified Adhesive . . . . . . . . . . . Disassembling in the Case of Soft Adhesive . . . . . . . . . . . . . . . Cleaning and Assembling Applicators . . . . . . . . . . . . . . . . . . . . . . .

5‐1 5‐2 5‐2 5‐2 5‐2

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6‐1

LV 227 Edition 06/14

 2014 Nordson Corporation

Table of Contents

 2014 Nordson Corporation

III

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How to Use Illustrated Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . Updated Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gun, LV 227 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gun, LV 227, 24VDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gun, LV 227, 110VAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gun, LV 227 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gun, LV 227, 240VAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gun, LV 227, 24 VDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gun, LV 227, 24VDC, Chemical resistant seals . . . . . . . . . . Gun, LV 227, 24VDC, Corrosion resistant . . . . . . . . . . . . . . . Gun body, complete, LV 227 . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gun body, complete, LV 227 . . . . . . . . . . . . . . . . . . . . . . . . . . Gun body, complete, LV 227, Chemical resistant seals . . . Gun body, complete, LV 227, Corrosion resistant . . . . . . . . Kit, Needle & Nozzle, LV 227 . . . . . . . . . . . . . . . . . . . . . . . . . . . . Kit, Needle & Nozzle, LV 227 . . . . . . . . . . . . . . . . . . . . . . . . . Gun Body, assy, LV 227 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gun body, assy, LV 227 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gun body, assy, LV 227, Chemical resistant seals . . . . . . . Seal adapter, LV 227 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seal adapter, LV 227, assy . . . . . . . . . . . . . . . . . . . . . . . . . . . Seal adapter, LV 227, Chemical resistant seals . . . . . . . . . . Seal kit, LV 227 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seal kit, LV 227 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seal kit, LV 227, Chemical resistant . . . . . . . . . . . . . . . . . . . . Gun, LV 227C, 24VDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gun, LV 227C, 24VDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gun, LV 227C, 24VDC, Wear resistant . . . . . . . . . . . . . . . . . Gun body, complete, LV 227C . . . . . . . . . . . . . . . . . . . . . . . . . . . Gun body, complete, LV 227C . . . . . . . . . . . . . . . . . . . . . . . . Kit, Needle & Nozzle, LV 227C . . . . . . . . . . . . . . . . . . . . . . . . . . Kit, Needle & Nozzle, LV 227C . . . . . . . . . . . . . . . . . . . . . . . . Kit, Needle & Nozzle, LV 227C, Wear resistant . . . . . . . . . . Gun body, assy, LV 227C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gun body, assy, LV 227C . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seal kit, LV 227C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seal kit, LV 227C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nozzle Covering LV 227 (complete) . . . . . . . . . . . . . . . . . . . . . . Nozzle Covering LV 227 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nozzle Covering Solenoid LV 227 . . . . . . . . . . . . . . . . . . . . . . . . Manifold Kit NC LV 227 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FC Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7‐1 7‐1 7‐1 7‐2 7‐2 7‐3 7‐3 7‐4 7‐5 7‐6 7‐7 7‐7 7‐8 7‐9 7‐9 7‐9 7‐10 7‐11 7‐12 7‐13 7‐13 7‐14 7‐15 7‐15 7‐16 7‐17 7‐17 7‐18 7‐19 7‐19 7‐20 7‐21 7‐22 7‐23 7‐23 7‐24 7‐25 7‐26 7‐27 7‐28 7‐30 7‐32 7‐34 7‐36 7‐37 7‐38

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Data LV 227 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8‐1 8‐1 8‐3

LV 227 Edition 06/14

P/N 405030_05

IV

Table of Contents

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Introduction

O‐1

Nordson International http://www.nordson.com/Directory Country

Phone

Fax

Austria

43‐1‐707 5521

43‐1‐707 5517

Belgium

31‐13‐511 8700

31‐13‐511 3995

Czech Republic

4205‐4159 2411

4205‐4124 4971

Denmark

Hot Melt

45‐43‐66 0123

45‐43‐64 1101

Finishing

45‐43‐200 300

45‐43‐430 359

Finland

358‐9‐530 8080

358‐9‐530 80850

France

33‐1‐6412 1400

33‐1‐6412 1401

Erkrath

49‐211‐92050

49‐211‐254 658

Lüneburg

49‐4131‐8940

49‐4131‐894 149

Nordson UV

49‐211‐9205528

49‐211‐9252148

EFD

49‐6238 920972

49‐6238 920973

Italy

39‐02‐216684‐400

39‐02‐26926699

Netherlands

31‐13‐511 8700

31‐13‐511 3995

47‐23 03 6160

47‐23 68 3636

Poland

48‐22‐836 4495

48‐22‐836 7042

Portugal

351‐22‐961 9400

351‐22‐961 9409

Russia

7‐812‐718 62 63

7‐812‐718 62 63

Slovak Republic

4205‐4159 2411

4205‐4124 4971

Spain

34‐96‐313 2090

34‐96‐313 2244

Sweden

46‐40-680 1700

46‐40‐932 882

Switzerland

41‐61‐411 3838

41‐61‐411 3818

Hot Melt

44‐1844‐26 4500

44‐1844‐21 5358

Industrial Coating Systems

44‐161‐498 1500

44‐161‐498 1501

49‐211‐92050

49‐211‐254 658

Europe

Germany

Norway

United Kingdom

Hot Melt

Distributors in Eastern & Southern Europe DED, Germany

2012 Nordson Corporation All rights reserved

NI_Q-1112-MX

O‐2

Introduction

Outside Europe For your nearest Nordson office outside Europe, contact the Nordson offices below for detailed information.

Contact Nordson

Phone

Fax

DED, Germany

49‐211‐92050

49‐211‐254 658

Pacific South Division, USA

1‐440‐685‐4797

-

China

86-21-3866 9166

86-21-3866 9199

Japan

81‐3‐5762 2700

81‐3‐5762 2701

Canada

1‐905‐475 6730

1‐905‐475 8821

Hot Melt

1‐770‐497 3400

1‐770‐497 3500

Finishing

1‐880‐433 9319

1‐888‐229 4580

Nordson UV

1‐440‐985 4592

1‐440‐985 4593

Africa / Middle East

Asia / Australia / Latin America

China

Japan

North America USA

NI_Q-1112-MX

2012Nordson Corporation All rights reserved

Safety

1‐1

Section 1 Safety Read this section before using the equipment. This section contains recommendations and practices applicable to the safe installation, operation, and maintenance (hereafter referred to as “use”) of the product described in this document (hereafter referred to as “equipment”). Additional safety information, in the form of task‐specific safety alert messages, appears as appropriate throughout this document. WARNING! Failure to follow the safety messages, recommendations, and hazard avoidance procedures provided in this document can result in personal injury, including death, or damage to equipment or property.

Safety Alert Symbols The following safety alert symbol and signal words are used throughout this document to alert the reader to personal safety hazards or to identify conditions that may result in damage to equipment or property. Comply with all safety information that follows the signal word. WARNING! Indicates a potentially hazardous situation that, if not avoided, can result in serious personal injury, including death.

CAUTION! Indicates a potentially hazardous situation that, if not avoided, can result in minor or moderate personal injury.

CAUTION! (Used without the safety alert symbol) Indicates a potentially hazardous situation that, if not avoided, can result in damage to equipment or property.

 2014 Nordson Corporation

Safe_PPA1011LUE_EN

1‐2

Safety

Responsibilities of the Equipment Owner Equipment owners are responsible for managing safety information, ensuring that all instructions and regulatory requirements for use of the equipment are met, and for qualifying all potential users.

Safety Information  Research and evaluate safety information from all applicable sources, including the owner‐specific safety policy, best industry practices, governing regulations, material manufacturer's product information, and this document.

 Make safety information available to equipment users in accordance with governing regulations. Contact the authority having jurisdiction for information.

 Maintain safety information, including the safety labels affixed to the equipment, in readable condition.

Instructions, Requirements, and Standards  Ensure that the equipment is used in accordance with the information provided in this document, governing codes and regulations, and best industry practices.

 If applicable, receive approval from your facility's engineering or safety department, or other similar function within your organization, before installing or operating the equipment for the first time.

 Provide appropriate emergency and first aid equipment.  Conduct safety inspections to ensure required practices are being followed.

 Re‐evaluate safety practices and procedures whenever changes are made to the process or equipment.

Safe_PPA1011LUE_EN

 2014 Nordson Corporation

Safety

1‐3

User Qualifications Equipment owners are responsible for ensuring that users:

 receive safety training appropriate to their job function as directed by governing regulations and best industry practices

 are familiar with the equipment owner's safety and accident prevention policies and procedures

 receive equipment‐ and task‐specific training from another qualified individual NOTE: Nordson can provide equipment‐specific installation, operation, and maintenance training. Contact your Nordson representative for information

 possess industry‐ and trade‐specific skills and a level of experience appropriate to their job function

 are physically capable of performing their job function and are not under the influence of any substance that degrades their mental capacity or physical capabilities

Applicable Industry Safety Practices The following safety practices apply to the use of the equipment in the manner described in this document. The information provided here is not meant to include all possible safety practices, but represents the best safety practices for equipment of similar hazard potential used in similar industries.

Intended Use of the Equipment  Use the equipment only for the purposes described and within the limits specified in this document.

 Do not modify the equipment.  Do not use incompatible materials or unapproved auxiliary devices. Contact your Nordson representative if you have any questions on material compatibility or the use of non‐standard auxiliary devices.

 2014 Nordson Corporation

Safe_PPA1011LUE_EN

1‐4

Safety

Instructions and Safety Messages  Read and follow the instructions provided in this document and other referenced documents.

 Familiarize yourself with the location and meaning of the safety warning labels and tags affixed to the equipment. Refer to Safety Labels and Tags at the end of this section.

 If you are unsure of how to use the equipment, contact your Nordson representative for assistance.

Installation Practices  Install the equipment in accordance with the instructions provided in this document and in the documentation provided with auxiliary devices.

 Ensure that the equipment is rated for the environment in which it will be used. This equipment has not been certified for compliance with the ATEX directive nor as nonincendive and should not be installed in potentially explosive environments.

 Ensure that the processing characteristics of the material will not create a hazardous environment. Refer to the Material Safety Data Sheet (MSDS) for the material.

 If the required installation configuration does not match the installation instructions, contact your Nordson representative for assistance.

 Position the equipment for safe operation. Observe the requirements for clearance between the equipment and other objects.

 Install lockable power disconnects to isolate the equipment and all independently powered auxiliary devices from their power sources.

 Properly ground all equipment. Contact your local building code enforcement agency for specific requirements.

 Ensure that fuses of the correct type and rating are installed in fused equipment.

 Contact the authority having jurisdiction to determine the requirement for installation permits or inspections.

Operating Practices  Familiarize yourself with the location and operation of all safety devices and indicators.

 Confirm that the equipment, including all safety devices (guards, interlocks, etc.), is in good working order and that the required environmental conditions exist.

 Use the personal protective equipment (PPE) specified for each task. Refer to Equipment Safety Information or the material manufacturer's instructions and MSDS for PPE requirements.

 Do not use equipment that is malfunctioning or shows signs of a potential malfunction.

Safe_PPA1011LUE_EN

 2014 Nordson Corporation

Safety

1‐5

Maintenance and Repair Practices  Allow only personnel with appropriate training and experience to operate or service the equipment.

 Perform scheduled maintenance activities at the intervals described in this document.

 Relieve system hydraulic and pneumatic pressure before servicing the equipment.

 De‐energize the equipment and all auxiliary devices before servicing the equipment.

 Use only new Nordson‐authorized refurbished or replacement parts.  Read and comply with the manufacturer's instructions and the MSDS supplied with equipment cleaning compounds. NOTE: MSDSs for cleaning compounds that are sold by Nordson are available at www.nordson.com or by calling your Nordson representative.

 Confirm the correct operation of all safety devices before placing the equipment back into operation.

 Dispose of waste cleaning compounds and residual process materials according to governing regulations. Refer to the applicable MSDS or contact the authority having jurisdiction for information.

 Keep equipment safety warning labels clean. Replace worn or damaged labels.

Equipment Safety Information This equipment safety information is applicable to the following types of Nordson equipment:

 hot melt and cold adhesive application equipment and all related accessories

 pattern controllers, timers, detection and verification systems, and all other optional process control devices

 2014 Nordson Corporation

Safe_PPA1011LUE_EN

1‐6

Safety

Equipment Shutdown To safely complete many of the procedures described in this document, the equipment must first be shut down. The level of shut down required varies by the type of equipment in use and the procedure being completed. If required, shut down instructions are specified at the start of the procedure. The levels of shut down are:

Relieving System Hydraulic Pressure Completely relieve system hydraulic pressure before breaking any hydraulic connection or seal. Refer to the melter‐specific product manual for instructions on relieving system hydraulic pressure.

De‐energizing the System Isolate the system (melter, hoses, applicators, and optional devices) from all power sources before accessing any unprotected high‐voltage wiring or connection point. 1. Turn off the equipment and all auxiliary devices connected to the equipment (system). 2. To prevent the equipment from being accidentally energized, lock and tag the disconnect switch(es) or circuit breaker(s) that provide input electrical power to the equipment and optional devices. NOTE: Government regulations and industry standards dictate specific requirements for the isolation of hazardous energy sources. Refer to the appropriate regulation or standard.

Disabling the Applicators NOTE: Adhesive dispensing applicators are referred to as “guns” in some previous publications. All electrical or mechanical devices that provide an activation signal to the applicators, applicator solenoid valve(s), or the melter pump must be disabled before work can be performed on or around an applicator that is connected to a pressurized system. 1. Turn off or disconnect the applicator triggering device (pattern controller, timer, PLC, etc.). 2. Disconnect the input signal wiring to the applicator solenoid valve(s). 3. Reduce the air pressure to the applicator solenoid valve(s) to zero; then relieve the residual air pressure between the regulator and the applicator.

Safe_PPA1011LUE_EN

 2014 Nordson Corporation

Safety

1‐7

General Safety Warnings and Cautions Table 1‐1 contains the general safety warnings and cautions that apply to Nordson hot melt and cold adhesive equipment. Review the table and carefully read all of the warnings or cautions that apply to the type of equipment described in this manual. Equipment types are designated in Table 1‐1 as follows: HM = Hot melt (melters, hoses, applicators, etc.) PC = Process control CA = Cold adhesive (dispensing pumps, pressurized container, and applicators) Table 1‐1 General Safety Warnings and Cautions Equipment Type

HM

HM

HM, CA

Warning or Caution

WARNING! Hazardous vapors! Before processing any polyurethane reactive (PUR) hot melt or solvent‐based material through a compatible Nordson melter, read and comply with the material's MSDS. Ensure that the material's processing temperature and flashpoints will not be exceeded and that all requirements for safe handling, ventilation, first aid, and personal protective equipment are met. Failure to comply with MSDS requirements can cause personal injury, including death.

WARNING! Reactive material! Never clean any aluminum component or flush Nordson equipment with halogenated hydrocarbon fluids. Nordson melters and applicators contain aluminum components that may react violently with halogenated hydrocarbons. The use of halogenated hydrocarbon compounds in Nordson equipment can cause personal injury, including death.

WARNING! System pressurized! Relieve system hydraulic pressure before breaking any hydraulic connection or seal. Failure to relieve the system hydraulic pressure can result in the uncontrolled release of hot melt or cold adhesive, causing personal injury. Continued...

 2014 Nordson Corporation

Safe_PPA1011LUE_EN

1‐8

Safety

General Safety Warnings and Cautions (contd.) Table 1‐1 General Safety Warnings and Cautions (contd) Equipment Type

HM

HM, PC

HM, CA, PC

HM, CA, PC

Warning or Caution

WARNING! Molten material! Wear eye or face protection, clothing that protects exposed skin, and heat‐protective gloves when servicing equipment that contains molten hot melt. Even when solidified, hot melt can still cause burns. Failure to wear appropriate personal protective equipment can result in personal injury.

WARNING! Equipment starts automatically! Remote triggering devices are used to control automatic hot melt applicators. Before working on or near an operating applicator, disable the applicator's triggering device and remove the air supply to the applicator's solenoid valve(s). Failure to disable the applicator's triggering device and remove the supply of air to the solenoid valve(s) can result in personal injury.

WARNING! Risk of electrocution! Even when switched off and electrically isolated at the disconnect switch or circuit breaker, the equipment may still be connected to energized auxiliary devices. De‐energize and electrically isolate all auxiliary devices before servicing the equipment. Failure to properly isolate electrical power to auxiliary equipment before servicing the equipment can result in personal injury, including death.

WARNING! Risk of fire or explosion! Nordson adhesive equipment is not rated for use in explosive environments and has not been cerfified for the ATEX directive or as nonincendive. In addition, this equipment should not be used with solvent‐based adhesives that can create an explosive atmosphere when processed. Refer to the MSDS for the adhesive to determine its processing characteristics and limitations. The use of incompatible solvent‐based adhesives or the improper processing of solvent‐based adhesives can result in personal injury, including death. Continued...

Safe_PPA1011LUE_EN

 2014 Nordson Corporation

Safety

1‐9

Table 1‐1 General Safety Warnings and Cautions (contd) Equipment Type

HM, CA, PC

HM

HM

HM, CA

HM

 2014 Nordson Corporation

Warning or Caution

WARNING! Allow only personnel with appropriate training and experience to operate or service the equipment. The use of untrained or inexperienced personnel to operate or service the equipment can result in injury, including death, to themselves and others and can damage to the equipment.

CAUTION! Hot surfaces! Avoid contact with the hot metal surfaces of applicators, hoses, and certain components of the melter. If contact can not be avoided, wear heat‐protective gloves and clothing when working around heated equipment. Failure to avoid contact with hot metal surfaces can result in personal injury.

CAUTION! Some Nordson melters are specifically designed to process polyurethane reactive (PUR) hot melt. Attempting to process PUR in equipment not specifically designed for this purpose can damage the equipment and cause premature reaction of the hot melt. If you are unsure of the equipment's ability to process PUR, contact your Nordson representative for assistance.

CAUTION! Before using any cleaning or flushing compound on or in the equipment, read and comply with the manufacturer's instructions and the MSDS supplied with the compound. Some cleaning compounds can react unpredictably with hot melt or cold adhesive, resulting in damage to the equipment.

CAUTION! Nordson hot melt equipment is factory tested with Nordson Type R fluid that contains polyester adipate plasticizer. Certain hot melt materials can react with Type R fluid and form a solid gum that can clog the equipment. Before using the equipment, confirm that the hot melt is compatible with Type R fluid.

Safe_PPA1011LUE_EN

1‐10 Safety

Other Safety Precautions  Do not use an open flame to heat hot melt system components.  Check high pressure hoses daily for signs of excessive wear, damage, or leaks.

 Never point a dispensing handgun at yourself or others.  Suspend dispensing handguns by their proper suspension point.

First Aid If molten hot melt comes in contact with your skin: 1. Do NOT attempt to remove the molten hot melt from your skin. 2. Immediately soak the affected area in clean, cold water until the hot melt has cooled. 3. Do NOT attempt to remove the solidified hot melt from your skin. 4. In case of severe burns, treat for shock. 5. Seek expert medical attention immediately. Give the MSDS for the hot melt to the medical personnel providing treatment.

Safe_PPA1011LUE_EN

 2014 Nordson Corporation

Introduction

2‐1

Section 2 Introduction Intended Use The LV 227 applicator - hereafter also referred to as Applicator - has been specially designed to process water-based cold glue - hereafter referred to as Adhesive. It is used for continuous or intermittent non-contact adhesive application. Any other use is considered to be unintended. The manufacturer is not liable for personal injury or property damage resulting from unintended use. Intended use includes observing the manufacturer’s prescribed operating, maintenance and service regulations. The product described here is only to be operated, serviced and maintained by persons who are familiar with the product and are aware of potential hazards. The applicable rules for the prevention of accidents as well as any other generally recognized safety regulations and occupational health regulations are to be observed. The manufacturer is by no means liable for any damage resulting from unauthorized modifications.

Safety Instructions Prior to installation and initial operation of the system, it is essential to read and follow the safety instructions. The general safety instructions are enclosed as an annex to the documentation folder or they are a section of this manual. The specific safety instructions are part of this manual.

Updated Parts List Please observe that your Nordson equipment may differ slightly from that described in the manual or certain information provided in it. Refer to the updated Parts List which is packed with your equipment.

 2014 Nordson Corporation

LV 227 Edition 06/14

P/N 405030_05

2‐2

Introduction

General Information The LV 227 applicator has been specially developed for the application of water‐based cold glue (adhesives). It is particularly suited to intermittent application of adhesive. A special seal allows the applicator to be used with adhesive pressure up to 42 bar. The knurled screw on the top section of the applicator is used to adjust the stem stroke during operation, enabling the adhesive quantity to be precisely adapted to the respective requirements. Air is applied to both sides of the working piston. A pressure spring causes a nozzle stem to close the nozzle even if the control air is switched off, e.g. during a system shutdown. The spring is equipped to operate with an adhesive pressure of up to approx. 42 bar. Control air is generally triggered by the flanged electrical solenoid valve with 24 VDC, 110 VAC or 240 VAC.

Functioning When the flanged electrical solenoid valve is opened by triggering it electrically, control air is applied via the solenoid valve to the air piston in the control module and the nozzle is opened by raising the nozzle stem. The electrical solenoid valve is closed with the aid of compressed air as well as with a closing spring.

Intermittent Adhesive Application Adhesive can be applied intermittently or continuously. The solenoid valve transmits the control pulses to the control module air piston. The control air pressure must be adapted to the applied switching frequency. Even five intermissions per second mean that this pressure must be 6 bar.

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Installation

3‐1

Section 3 Installation ATTENTION: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation.

Installing Applicator in Machines Due to possible self‐vibrations caused by intermittent operation, the applicator should be installed as firmly and sturdily as possible. The transmission of vibrations from machinery to the applicator should be avoided as much as possible.

 2014 Nordson Corporation

LV 227 Edition 06/14

P/N 405030_05

3‐2

Installation

Connections Connecting the Solenoid Valve Connection with the included plug, which must be screwed securely into place. The solenoid valves are standardly designed for 24 VDC, 110 VAC or 240 VAC. The voltage indicated on the solenoid valve ID plate is decisive.

Connecting Control Air Connect control air of max. 6 bar to the control air fitting (B).

Connecting the Material Line Remove the protective cap from the material connection and connect the material hose from the pressure tank or adhesive pump (A).

Operating Instructions Adjusting the adhesive quantity / stem stroke The required adhesive quantity or application pattern is set by

 Adjusting the output quantity (pressure container or adhesive pump) and  Adjusting the stem stroke. Optimal adhesive application is achieved by adjusting alternately. The stem stroke adjustment (C) affects the maximum nozzle stem stroke and thus the adhesive quantity flowing out of the nozzle. Turn to the left to increase the adhesive quantity. Turn to the right to decrease the adhesive quantity. NOTE: To prevent the adhesive from hardening in the nozzle tip during extended machine standstill, the nozzle should be sealed airtight (e.g. with grease or Vaseline).

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Installation

B

3‐3

C

A

Fig. 3‐1

Cross-section, LV 227

B

C

A

Fig. 3‐2

 2014 Nordson Corporation

Cross-section, LV 227C

LV 227 Edition 06/14

P/N 405030_05

3‐4

Installation

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Operation

4‐1

Section 4 Operation ATTENTION: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation.

General Adhesive Processing Instructions NOTE: The following information is particularly important for the processing of adhesives but is also applicable to other materials:

 Always pre‐test your Nordson product before applying it for its ultimate purpose.

 The surface to be bonded should be at room temperature and free of dust, grease and moisture.

 The suitable material, optimum working conditions and possible pre-treatment of the substrate must be determined by testing.

 Some substrates contain softeners and other components which may become volatile later. Occasionally, surfaces are covered with wax, isolating oil, etc. The bonding may fail immediately or later if pre-treatment/tests are not carried out. NOTE: Observe any comment sheets concerning the process to the material used.

Compatibility of Different Types of Adhesive NOTE: Not all types of adhesive are compatible. The material may become degraded if improperly used, resulting in function faults and possibly unit damage. Nordson is not be liable for danger or damage resulting from the materials. Materials may be processed only when the manufacturer's product descriptions and Safety Data Sheets are observed. They include information on correct processing, transport, storage and disposal. Information regarding reactivity and potentially hazardous decomposition products, toxic properties, flash points, etc. can also be found there.

 2014 Nordson Corporation

LV 227 Edition 06/14

P/N 405030_05

4‐2

Operation

Emergency Shutdown Find out about proper behavior in emergency situations and know the location and activation of EMERGENCY OFF operating elements installed in the production area. ATTENTION: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation. 1. Trigger the nearest EMERGENCY OFF element (EMERGENCY STOP button, EMERGENCY OFF ripcord or main switch with EMERGENCY OFF function). 2. Determine and remedy the cause of EMERGENCY OFF before switching the system on again.

Initial Startup 1. Set the air pressure on the adhesive pump so that the hydraulic pressure does not exceed 42 bar (600 psi). NOTE: Do not exceed 42 bar (600 psi). A higher pressure may damage the applicator. 2. Place a container underneath the applicator and switch on the control unit. 3. Set the control unit such that the adhesive flows out of the applicator nozzle evenly and without any air bubbles. 4. Carry out test gluing and check the adhesive bead. If a thicker bead is required, the adhesive pressure can be increased but not over 42 bar (600 psi).

Daily Startup 1. Check whether there is sufficient adhesive in the reservoir. 2. Release the air pressure for the adhesive pump.

Daily Shutdown 1. Shut off the compressed air supply to the adhesive pump (reduce to 0 bar). 2. Close the nozzle orifices with silicone paste, Nordson P/N 311 642.

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Maintenance

5‐1

Section 5 Maintenance ATTENTION: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation. Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation. ATTENTION: Disconnect adhesive, power and air supply!

ATTENTION: When possible, always wear protective gloves when carrying out the work. Ensure that the material to be applied is clean and filtered. The control air should also be clean and, under certain circumstances, lightly oiled when fed to the equipment. Individual operating conditions and different application material require a corresponding minimum effort for maintenance. Do not use metallic, sharp‐edged tools to clean the outside of the equipment, e.g. nozzle tips, only use soft brushes. When carrying out repair or maintenance work, keep the working space as well as the gun to be repaired as clean as possible. Polluted adhesive guns should be thoroughly purged when possible. This applies particularly when a nozzle stem, sealing element or material nozzle needs to be replaced. The adhesive guns should not remain installed for any important maintenance work but be removed from the machine. Stop the pressure and material supply lines beforehand.

 2014 Nordson Corporation

LV 227 Edition 06/14

P/N 405030_05

5‐2

Maintenance

Disassembling an Applicator Disassembling in the Case of Solidified Adhesive Do not disassemble an applicator in which adhesive has solidified! This would most likely destroy sensitive components. We recommend immersing the adhesive gun, without the solenoid valve, in warm water for 1 - 2 days to soften the glue. Repeat the process several times, if necessary. If the applicator still cannot be disassembled, return it to us for repair.

Disassembling in the Case of Soft Adhesive NOTE: Interrupt the control air.

 Detach the solenoid valve and material nozzle  Purge the applicator through the material connection with warm water until the water flows out free of adhesive residue. NOTE: Disassemble the individual components with extreme caution!

 Extract the sealing screw by turning to the left with a screwdriver that fits properly. NOTE: The sealing screw and body can be easily damaged if an unsuitable tool is used or the screw is turned in the wrong direction.

 Check all parts for damage or wear after disassembling, particularly the sealing elements.

Cleaning and Assembling Applicators All of the parts must be carefully cleaned with water or a mild vinegar solution before assembling. NOTE: When a used material nozzle is reinstalled, it must first be thoroughly purged with cleaning agent to ensure that no material residue remains in the nozzle. The shaft of the nozzle stem must also be free of any residual particles. If the stems are not thoroughly cleaned, leakage will occur immediately. Do not use metallic or sharp tools or aids to install the O‐rings. Lubricate the O‐rings before installing. Use the lubricant supplied with the seal kit.

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Troubleshooting

6‐1

Section 6 Troubleshooting ATTENTION: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation.

Problem

Possible cause

No adhesive comes out of the applicator

No compressed air connected to the applicator.

Connect compressed air.

No voltage supplied.

When the applicator is activated, the LED in the electrical plug connector should be illuminated.

Hardened adhesive

Clean the nozzle tips. If that does not help, remove the nozzle and clean it.

Adhesive pressure too high

Reduce adhesive pressure.

Charred adhesive in the nozzle or on the stem.

Remove the nozzle and clean adhesive off of nozzle and stem.

Sealing rings are defective.

Replace the sealing rings.

Adhesive drips from the nozzle.

Adhesive drips from the detection hole in the seal adapter.

 2014 Nordson Corporation

Corrective action

LV 227 Edition 06/14

Refer to

Section 5

Section 5

P/N 405030_05

6‐2

Troubleshooting

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

7‐1

Section 7 Parts How to Use Illustrated Parts List The parts in this section are divided into the following columns: Item — Identifies the parts shown, available from Nordson. Part — Nordson spare part number for each available part shown in the illustration. A series of hyphens (‐ ‐ ‐ ‐ ‐) in the Parts column means that the part cannot be ordered separately. Description — This column contains the name of the part and, when appropriate, the dimensions and other properties. The dots in the Description column illustrate the relationship between assemblies, subassemblies and individual parts. Quantity— The quantity required per unit, assembly or subassembly. The abbreviation AR (as required) is used to designate that items are stated in drum sizes or that the quantity required per assembly is a factor of the product version or the model. NOTE: The texts are available only in English.

Updated Parts List Please observe that your unit may differ slightly from the description or from certain details in the manual. Use only the most recent Parts List which is packed with your equipment.

 2014 Nordson Corporation

LV 227 Edition 06/14

P/N 405030_05

7‐2

Parts

Spare Parts Gun, LV 227

1

3

1

2 Fig. 7‐1

Gun, LV 227

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

7‐3

Gun, LV 227, 24VDC Item ­ ­ ­ ­ ­ ­ 1 2

3

Part 372843 372844 372845 372846 372847 372848 378750 372573 372574 372575 372576 372577 372578 771307

Description Gun, LV 227, 0.3mm, 24VDC Gun, LV 227, 0.4mm, 24VDC Gun, LV 227, 0.6mm, 24VDC Gun, LV 227, 0.8mm, 24VDC Gun, LV 227, 1.2mm, 24VDC Gun, LV 227, 1.5mm, 24VDC Gun body, complete, LV 227 Nozzle, LV 227, 0.3mm Nozzle, LV 227, 0.4mm Nozzle, LV 227, 0.6mm Nozzle, LV 227, 0.8mm Nozzle, LV 227, 1.2mm Nozzle, LV 227, 1.5mm Solenoid valve, 24VDC

Qty ­ ­ ­ ­ ­ ­ 1 1 1 1 1 1 1 1

Remarks

See: ­ Gun body, complete, LV 227 ­ Kit, Needle & Nozzle, LV 227 ­ Seal kit, LV 227

Gun, LV 227, 110VAC Item ­ ­ ­ ­ ­ ­ 1 2

3

Part 372849 372850 372851 372852 372853 372854 378750 372573 372574 372575 372576 372577 372578 771139

 2014 Nordson Corporation

Description Gun, LV 227, 0.3mm, 110VAC Gun, LV 227, 0.4mm, 110VAC Gun, LV 227, 0.6mm, 110VAC Gun, LV 227, 0.8mm, 110VAC Gun, LV 227, 1.2mm, 110VAC Gun, LV 227, 1.5mm, 110VAC Gun body, complete, LV 227 Nozzle, LV 227, 0.3mm Nozzle, LV 227, 0.4mm Nozzle, LV 227, 0.6mm Nozzle, LV 227, 0.8mm Nozzle, LV 227, 1.2mm Nozzle, LV 227, 1.5mm Solenoid valve, 110VAC

LV 227 Edition 06/14

Qty ­ ­ ­ ­ ­ ­ 1 1 1 1 1 1 1 1

Remarks

See: ­ Gun body, complete, LV 227 ­ Kit, Needle & Nozzle, LV 227 ­ Seal kit, LV 227

P/N 405030_05

7‐4

Parts

Gun, LV 227

1

3

1

2 Fig. 7‐2

Gun, LV 227

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

7‐5

Gun, LV 227, 240VAC Item ­ ­ ­ ­ ­ ­ 1 2

3

Part 373381 373382 373383 373384 373385 373386 378750 372573 372574 372575 372576 372577 372578 771142

 2014 Nordson Corporation

Description Gun, LV 227, 0.3mm, 240VAC Gun, LV 227, 0.4mm, 240VAC Gun, LV 227, 0.6mm, 240VAC Gun, LV 227, 0.8mm, 240VAC Gun, LV 227, 1.2mm, 240VAC Gun, LV 227, 1.5mm, 240VAC Gun body, complete, LV 227 Nozzle, LV 227, 0.3mm Nozzle, LV 227, 0.4mm Nozzle, LV 227, 0.6mm Nozzle, LV 227, 0.8mm Nozzle, LV 227, 1.2mm Nozzle, LV 227, 1.5mm Solenoid valve, 220VAC

LV 227 Edition 06/14

Qty ­ ­ ­ ­ ­ ­ 1 1 1 1 1 1 1 1

Remarks

See: ­ Gun body, complete, LV 227 ­ Kit, Needle & Nozzle, LV 227 ­ Seal kit, LV 227

P/N 405030_05

7‐6

Parts

Gun, LV 227, 24 VDC

1

3

1

2 Fig. 7‐1

Gun, LV 227, 24 VDC, Corrosion resistant

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

7‐7

Gun, LV 227, 24VDC, Chemical resistant seals Item ­

Part 377805

Description Gun, LV 227, 0.3mm, 24VDC. Chem. res. Seals

­

377806

Gun, LV 227, 0.4mm, 24VDC. Chem. res. Seals

­

­

377807

Gun, LV 227, 0.6mm, 24VDC. Chem. res. Seals

­

­

377808

Gun, LV 227, 0.8mm, 24VDC. Chem. res. Seals

­

­

377809

Gun, LV 227, 1.2mm, 24VDC. Chem. res. Seals

­

­

377810

Gun, LV 227, 1.5mm, 24VDC. Chem. res. Seals

­

1

377811

1

2

372573 372574 372575 372576 372577 372578 771307

Gun body, complete, LV 227. Chem. res. Seals Nozzle, LV 227, 0.3mm Nozzle, LV 227, 0.4mm Nozzle, LV 227, 0.6mm Nozzle, LV 227, 0.8mm Nozzle, LV 227, 1.2mm Nozzle, LV 227, 1.5mm Solenoid valve, 24VDC

3

Qty ­

1 1 1 1 1 1 1

Remarks

See: ­ Gun body, complete, LV 227, Chem. res. Seals ­ Kit, Needle & Nozzle, LV 227 ­ Seal kit, LV 227, Chemical resistant

Gun, LV 227, 24VDC, Corrosion resistant Item ­

Part 7302265

Description Gun, LV 227, 0.3mm, 24VDC, Corrosion resistant

1

7302283

2

372573

Gun body, complete, LV 227, Corrosion resistant Nozzle, LV 227, 0.3mm

3

771307

Solenoid valve, 24VDC

 2014 Nordson Corporation

Qty ­

Remarks

See: ­ Gun body, complete, LV 227, Corrosion resistant ­ Seal kit, LV 227 1

LV 227 Edition 06/14

P/N 405030_05

7‐8

Parts

Gun body, complete, LV 227

6

3

5

1

2 7

12345

4

Fig. 7‐2

Gun body, complete, LV 227

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

7‐9

Gun body, complete, LV 227 Item ­ 1 2

Part 378750 372861 372864

Description Gun body, complete, LV 227 Gun body, assy, LV 227 Needle, LV 227

Qty ­ 1 1

3 4 5 6 7

313920 372570 373029 ‐‐‐‐‐ 311551

Straight connector 6511­6­M5 Fitting, nipple, 1/8BSP­1/2­20 UNF, SS Manifold LV 227 Screw allenhead, M3x30, DIN912,SS,A2,70 Cap, plastic, 1/2"x20

1 1 1 2 1

Remarks See: Gun body, assy, LV 227 See: Kit, Needle & Nozzle, LV 227

See: Seal kit LV 227

Gun body, complete, LV 227, Chemical resistant seals Item ­

Part 377811

Description Gun body, complete, LV 227. Chem. res. Seals

Qty ­

Remarks

1

377812

Gun body, assy, LV 227, Chem. res. Seals

1

See: Gun body, assy, LV 227, Chem. res. Seals

2

372864

Needle, LV 227

1

See: Kit, Needle & Nozzle, LV 227

3 4 5

313920 372570 373029

Straight connector 6511­6­M5 Fitting, nipple, 1/8BSP­1/2­20 UNF, SS Manifold LV 227

1 1 1

6 7

‐‐‐‐‐ 311551

Screw allenhead, M3x30, DIN912,SS,A2,70 Cap, plastic, 1/2"x20

2 1

See: Seal kit, LV 227, Chemical resistant

Gun body, complete, LV 227, Corrosion resistant Item ­ 1

Part 7302283 372861

Description Gun body, complete, LV 227, Corrosion resistant Gun body, assy, LV 227

Qty ­ 1

2 3 4 5 6 7

7302226 313920 372570 373029 ‐‐‐‐‐ 311551

Needle, LV 227, Corr. Resist Straight connector 6511­6­M5 Fitting, nipple, 1/8BSP­1/2­20 UNF, SS Manifold LV 227 Screw allenhead, M3x30, DIN912,SS,A2,70 Cap, plastic, 1/2"x20

1 1 1 1 2 1

 2014 Nordson Corporation

LV 227 Edition 06/14

Remarks See: Gun body, assy, LV 227

See: Seal kit, LV 227

P/N 405030_05

7‐10 Parts

Kit, Needle & Nozzle, LV 227

2

1

Fig. 7‐3

Kit, Needle & Nozzle, LV 227

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

7‐11

Kit, Needle & Nozzle, LV 227 Item ­ ­ ­ ­ ­ ­ 1

2

Part 372855 372856 372857 372858 372859 372860 372573 372574 372575 372576 372577 372578 372864 313742

 2014 Nordson Corporation

Description Kit, Needle+Nozzle, LV 227, 0.3mm Kit, Needle+Nozzle, LV 227, 0.4mm Kit, Needle+Nozzle, LV 227, 0.6mm Kit, Needle+Nozzle, LV 227, 0.8mm Kit, Needle+Nozzle, LV 227, 1.2mm Kit, Needle+Nozzle, LV 227, 1.5mm Nozzle, LV 227, 0.3mm Nozzle, LV 227, 0.4mm Nozzle, LV 227, 0.6mm Nozzle, LV 227, 0.8mm Nozzle, LV 227, 1.2mm Nozzle, LV 227, 1.5mm Needle LV 227 O­ring 12x2

LV 227 Edition 06/14

Qty ­ ­ ­ ­ ­ ­ 1 1 1 1 1 1 1 1

Remarks

Included with Needle LV 227 See: Seal kit, LV 227

P/N 405030_05

7‐12 Parts

Gun Body, assy, LV 227

3

8

4

6 5 7

1

2

Fig. 7‐4

Gun Body, assy, LV 227

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

7‐13

Gun body, assy, LV 227 Item ­ 1 2 3 4 5

Part 372861 372562 313787 372579 256139 370468

Description Gun body, assy, LV 227 Gun, body LV 227 Cover, plastic protection Needle stroke adjustment LV 227 Compression spring 1x8x13 Seal adapter LV 227, assy

Qty ­ 1 1 1 1 1

6 7 8

‐‐‐‐‐ ‐‐‐‐‐ 311495

Screw Allenhead, M3x6, DIN912, A2 Washer, M3, DIN433 O­ring, 14x1.78, viton

1 1 1

Remarks

See: Seal kit, LV 227

See: Seal adapter, LV 227, assy

See: Seal kit LV 227

Gun body, assy, LV 227, Chemical resistant seals Item ­ 1 2

Part 377812 372562 313787

Description Gun body, assy, LV 227, Chem. res. Seals Gun, body LV 227 Cover, plastic protection

Qty ­ 1 1

3 4 5

372579 256139 377813

Needle stroke adjustment LV 227 Compression spring 1x8x13 Seal adapter LV 227, Chem. res. Seals

1 1 1

6 7 8

‐‐‐‐‐ ‐‐‐‐‐ 311495

Screw Allenhead, M3x6, DIN912, A2 Washer, M3, DIN433 O­ring, 14x1.78, viton

1 1 1

 2014 Nordson Corporation

LV 227 Edition 06/14

Remarks

See: Seal kit, LV 227, Chemical resistant

See: Seal adapter, LV 227, Chem. res. Seals

See: Seal kit, LV 227, Chemical resistant

P/N 405030_05

7‐14 Parts

Seal adapter, LV 227

3

2

5

1

4 Fig. 7‐5

Seal adapter, LV 227

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

7‐15

Seal adapter, LV 227, assy Item ­ 1 2 3 4 5

Part 370468 311483 313720 311478 313721 313934

Description Seal adapter LV 227, assy O­ring Seal adapter LV 227 O­ring Quadring O­ring

Qty ­ 1 1 1 1 1

Remarks See: Seal kit, LV 227 See: Seal kit, LV 227 See: Seal kit, LV 227 See: Seal kit, LV 227

Seal adapter, LV 227, Chemical resistant seals Item ­ 1

Part 377813 311483

Description Seal adapter LV 227, Chem. res. Seals, assy O­ring

Qty ­ 1

2 3

313720 311478

Seal adapter LV 227 O­ring

1 1

4

377348

Seal ring, chem. Resist

1

See: Seal kit, LV 227, Chemical resistant

5

313934

O­ring

1

See: Seal kit, LV 227, Chemical resistant

 2014 Nordson Corporation

LV 227 Edition 06/14

Remarks See: Seal kit, LV 227, Chemical resistant See: Seal kit, LV 227, Chemical resistant

P/N 405030_05

7‐16 Parts

Seal kit, LV 227

6

4

7

2

5

1

8

9 Fig. 7‐6

3

Seal kit, LV 227

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

7‐17

Seal kit, LV 227 Item ­ 1 2 3 4 5 6 7 8 9

Part 372873 313742 311478 313787 311483 311495 313721 313934 373029 313756

Description Seal kit, LV 227 O­ring, 12x2 O­ring, 2.9x1.78 Cover, plastic Protection O­ring, 6.07/N. NR.010 O­ring, 14x1.78 Quadring, Qrar, 2.9x1.78 O­ring, 8.5x2 Manifold, LV 227 Silicone grease, 10 gram

Qty ­ 1 1 1 1 1 1 1 1 1

Remarks

Qty ­ 1 1 1 1 1 1 1 1 1

Remarks

Seal kit, LV 227, Chemical resistant Item ­ 1 2 3 4 5 6 7 8 9

Part 372874 313742 311478 313787 311483 311495 377348 313934 373029 313756

 2014 Nordson Corporation

Description Seal kit, LV 227, Chemical resistant O­ring, 12x2 O­ring, 2.9x1.78 Cover, plastic Protection O­ring, 6.07/N. NR.010 O­ring, 14x1.78 O­ring 2.9x1.78, chem.resist. O­ring, 8.5x2 Manifold, LV 227 Silicone grease, 10 gram

LV 227 Edition 06/14

P/N 405030_05

7‐18 Parts

Gun, LV 227C, 24VDC 4

3

1

1

2

2 Fig. 7‐7

Gun, LV 227C, 24VDC

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

7‐19

Gun, LV 227C, 24VDC Item ­ ­ ­ ­ 1 2

3 4

Part 373915 373916 373917 373918 7303778 313410 313411 313412 313413 771113 370300

Description Gun, LV 227C, 0.4mm, 24VDC Gun, LV 227C, 0.6mm, 24VDC Gun, LV 227C, 0.8mm, 24VDC Gun, LV 227C, 1.2mm, 24VDC Gun body, complete, LV 227C Kit, needle+nozzle LV 227C, 0.4mm Kit, needle+nozzle LV 227C, 0.6mm Kit, needle+nozzle LV 227C, 0.8mm Kit, needle+nozzle LV 227C, 1.2mm Solenoid valve, 24VDC Connector with LED ind., 24V

Qty ­ ­ ­ ­ 1 1 1 1 1 1 1

Remarks

See: ­ Gun body, complete, LV 227C ­ Seal kit, LV 227C ­ Kit, Needle & Nozzle, LV 227C

Gun, LV 227C, 24VDC, Wear resistant Item ­

Part 7301726

­

7301729

1 2

7303778 7301728 7301731 771113 370300

3 4

 2014 Nordson Corporation

Description Gun, LV 227C, 0.6mm, 24VDC, Wear Resistant Gun, LV 227C, 1.2mm, 24VDC, Wear Resistant Gun body, complete, LV 227C Kit, needle+nozzle LV 227C, 0.6mm, W.R. Kit, needle+nozzle LV 227C, 1.2mm, W.R. Solenoid valve, 24VDC Connector with LED ind. 24V

LV 227 Edition 06/14

Qty ­

Remarks

­ 1 1 1 1 1

See: ­ Gun body, complete, LV 227C ­ Seal kit, LV 227C ­ Kit, Needle & Nozzle, LV 227C

P/N 405030_05

7‐20 Parts

Gun body, complete, LV 227C 2

4

5

1

3 Fig. 7‐8

Gun body, complete, LV 227C

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

7‐21

Gun body, complete, LV 227C Item ­ 1 2 3 4

Part 7303778 313831 313833 372570 ‐‐‐‐‐

Description Gun body, complete, LV 227C Gun body, assy, LV 227C Straight connector 6511­6­M5 Fitting, nipple, 1/8BSP­1/2­20 UNF, SS Screw allenhead, M3x30, DIN912,SS,A2,70

Qty ­ 1 1 1 2

5

311551

Cap, plastic, 1/2"x20

1

 2014 Nordson Corporation

LV 227 Edition 06/14

Remarks See: Gun body, assy, LV 227C

P/N 405030_05

7‐22 Parts

Kit, Needle & Nozzle, LV 227C

3

4

2

1 Fig. 7‐9

Kit, Needle & Nozzle, LV 227C

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

7‐23

Kit, Needle & Nozzle, LV 227C Item ­ ­ ­ ­ 3 4

Part 313410 313411 313412 313413 313741 313742

Description Kit, needle+nozzle LV 227C, 0.4mm Kit, needle+nozzle LV 227C, 0.6mm Kit, needle+nozzle LV 227C, 0.8mm Kit, needle+nozzle LV 227C, 1.2mm O­ring 6x2 O­ring 12x2

Qty ­ ­ ­ ­ 1 1

Remarks

See: Seal kit, LV 227C See: Seal kit, LV 227C

Kit, Needle & Nozzle, LV 227C, Wear resistant Item ­ ­ 1 2 3 4

Part 7301728 7301731 7301727 7301730 313405 313407 313741 313742

 2014 Nordson Corporation

Description Kit, needle+nozzle LV 227C, 0.6mm, W.R. Kit, needle+nozzle LV 227C, 1.2mm, W.R. Nozzle, LV 227C, 0.6mm Nozzle, LV 227C, 1.2mm Needle LV 227C, 0.6mm Needle LV 227C, 1.2mm O­ring 6x2 O­ring 12x2

LV 227 Edition 06/14

Qty ­ ­ 1 1 1 1 1 1

Remarks

See: Seal kit, LV 227C See: Seal kit, LV 227C

P/N 405030_05

7‐24 Parts

Gun body, assy, LV 227C

3

5 6

7

2

4 Fig. 7‐10

1

Gun body, assy, LV 227C

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

7‐25

Gun body, assy, LV 227C Item ­ 1 2 3 4 5 6 7

Part 313831 313787 ‐‐‐‐‐ 313828 313825 256139 ‐‐‐‐‐ 370468

 2014 Nordson Corporation

Description Gun body, assy, LV 227C Cover, plastic protection Screw, set, M3x4, DIN916, A2 Needle stroke adjustment Gun body LV 227C Compression spring Screw, set, M4x4, DIN916, A2 Seal adapter, LV 227, assy

LV 227 Edition 06/14

Qty ­ 1 1 1 1 1 1 1

Remarks See: Seal kit, LV 227C

See: Seal adapter, LV 227, assy

P/N 405030_05

7‐26 Parts

Seal kit, LV 227C

7

5

6

3

8

1

2

9

4 Fig. 7‐11

Seal kit, LV 227C

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

7‐27

Seal kit, LV 227C Item 1 2 3 4 5 6 7 8 9

Part 7303990 313741 313742 311478 313787 311483 313934 313721 313724 313756

 2014 Nordson Corporation

Description Seal kit LV 227C O­ring, 6x2 O­ring, 12x2 O­ring, 2.9x1.78 Cover, plastic protection O­ring O­ring Quadring, Qrar, 2.9x1.78 O­ring, 14x1 Silicone grease, 10 gram

LV 227 Edition 06/14

Qty 1 1 1 1 1 1 1 1 1

Remarks

P/N 405030_05

7‐28 Parts

Nozzle Covering LV 227 (complete)

2

1

Fig. 7‐12

Nozzle Covering LV 227 (complete)

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

Item

Part

Description

Qty

1

374 026

Nozzle Covering LV 227

1

2

374 027

Nozzle Covering Solenoid LV 227

1

 2014 Nordson Corporation

LV 227 Edition 06/14

7‐29

P/N 405030_05

7‐30 Parts

Nozzle Covering LV 227

14 13 11 3 10 12 6

1 9 8

7

2

4 5

15

Fig. 7‐13

Nozzle Covering LV 227

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

Item

Part

Description

Qty

1

373 569

Clamp, NC LV 227

1

2

373 570

Plate Cover NC LV 227

1

3

373 571

Cylinder, Bore 5/16” , stoke 1/2”

1

4

373 572

Swivel Block NC LV 227

1

5

373 573

Hinge Block NC LV 227

1

6

373 605

Hinge Pin M3x2.5, NC LV 227

2

7

373 604

Hinge Pin M3x6, NC LV 227

2

8

373 606

Shoulder Screw M3, NC LV 227

2

9

311 042

Screw allenhead M5x12 Stainl.

1

10

373 633

Gasket, NC LV 227 11761.4 nylon

5

11

373 634

Hose Fitting 10-32 to 1/16”

4

12

373 635

Adjustable fitting, 10-32

1

13

373 636

Hose Clip

4

14

373 906

Hose, Urethane 1/16x1/8, Clear

15

373 905

Sleeve, Silicone 18x1x14

 2014 Nordson Corporation

LV 227 Edition 06/14

7‐31

2 Mtr. 1

P/N 405030_05

7‐32 Parts

Nozzle Covering Solenoid LV 227

2

3

1

Fig. 7‐14

Nozzle Covering Solenoid LV 227

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

Item

Part

Description

Qty

1

373 637

Valve, Solenoid, NC LV 227

1

2

373 907

Cable, Connection for 373.637

1

3

373 908

Hose Fitting M5-6

1

 2014 Nordson Corporation

LV 227 Edition 06/14

7‐33

P/N 405030_05

7‐34 Parts

Manifold Kit NC LV 227

5 3 2 8 7

6 9 4 1

Fig. 7‐15

Manifold Kit NC LV 227

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

Item

Part

Description

7‐35

Qty

374 113

Manifold Kit NC LV 227 complete

1

1

374 114

Manifold NC LV 227 1-12

2

2

373 908

Hose Fitting M5-6

2

3

972141

Connector male, 6mm x 1/8RPT

2

4

377 116

Blind Plug M5

24

5

900586

Tubing, polthn, 6mm OD x 4mm

4 Mtr.

6

373 906

Hose, Urethane 1/16x1/8, Clear

12Mtr.

7

373 634

Hose Fitting 10-32 to 1/16”

24

8

373 633

Gasket, NC LV 227 11761.4 nylon

24

9

373 636

Hose Clip

24

 2014 Nordson Corporation

LV 227 Edition 06/14

P/N 405030_05

7‐36 Parts

FC Bracket

1

3

2

3

Fig. 7‐16

FC Bracket

Item

Part

Description

1

7303066

Bracket, FC, Drop Bar

2

7303067

Bracket, FC, Drop bar, w. Horz. Bar

3

7305351

Kit, Adapter, LV227, FC Bracket

NOTE: For using the brackets 7303066 or 7303067, adapter 7305351 is required.

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Parts

7‐37

Mounting Bracket

1

Fig. 7‐17

Mounting Bracket

Item 1

Part 377181

 2014 Nordson Corporation

Description Bracket, Mounting, LV227

LV 227 Edition 06/14

P/N 405030_05

7‐38 Parts

Cables Item ­ ­ ­ ­

Part 7302542 7302539 7302540 7302541

P/N 405030_05

Description Cable, PN. Gun to Lcomm, Hard wired, 10M Cable, Lcomm to sol. (16/16) PN. Gun 24V, 2.5M Cable, Lcomm to sol. (16/16) PN. Gun 24V, 5M Cable, Lcomm to sol. (16/16) PN. Gun 24V, 10M

LV 227 Edition 06/14

Qty ­ ­ ­ ­

Remarks

 2014 Nordson Corporation

Technical Data

8‐1

Section 8 Technical Data General Data LV 227 Applicator type

LV 227

Working air pressure

4 to 6 bar (57 - 87 psi)

Compressed air lubrication

Not necessary

Compressed air quality

Filtered, max. particle size 5 μm

Max. system pressure1

42 bar (600 psi)

Min. working material pressure2

1 bar (14.5 psi)

Max. working material pressure2

42 bar (600 psi)

Min. material viscosity

500 cps

Max. material

viscosity3

20000 cps

Recommended pH-value (material)

4 to 7

Compressed air connection (OD)

6 mm (5.994 mm.)

Material connection

½” 20-UNF

Solenoid valve connection

Connecting cable OD 6 - 8 mm

Solenoid valve voltage4

24 VDC / 5,4 W, 110 VAC or 240 VAC

IP class

IP 65

Minimal uptime5

5 ms

Minimum downtime5

8.5 ms

Permitted ambient temperature

10 to 50 °C (50 to 122 °F)

NOTE: 1 Max. system pressure. Safe maximum system pressure. NOTE: 2 Working material pressure. Minimum and maximum working material pressure at which proper operation is ensured (depends on the material viscosity). NOTE: 3 When the material viscosity is > 5000 cps, it is advisable to use an adhesive pump with continuous flow. ATTENTION: 4 Risk of damage! Do not use switching accelerators that shorten the solenoid valve switching times with a brief surge impulse. Trigger the solenoid valve only with voltage of 24 VDC, 110 VAC or 120 VAC. Higher voltage (e.g. voltage peaks) will damage the solenoid valves. NOTE: 5 The time is heavily dependent on the adhesive and only serves as a

guideline value. The minimum uptime is related to the bead length, the minimum downtime to the distance between two beads (the stitch).

 2014 Nordson Corporation

LV 227 Edition 06/14

P/N 405030_05

8‐2

Technical Data

NOTE: The data and descriptions contained in our product information are intended to provide a general overview of our products and services. Most of the data was obtained through testing in our internal testing environment, so it may not apply under other circumstances. Although we invest every effort to provide data and information that is accurate, we will assume no liability, guarantee or warranty whatsoever for the correctness, completeness or currency. 1 bar = 14.5 psi = 105Pa

0.4536 kg = 0.45 kg

9 x °C / 5 + 32 = °F

25.4 mm = 1 in.

1 cps = 1 cP = 1 mPa s = 1 mNs/m2

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Technical Data

8‐3

Dimensions

20 (0.79 in)

40 (1.57 in)

1/2 - 20UNF

51,2 (2.02 in)

113,7 (4.48 in)

105,2 (4.14 in)

94,5 (3.72 in)

10 (0.39 in) 24,5 (0.96 in) 30 (1.18 in)

 2014 Nordson Corporation

LV 227 Edition 06/14

P/N 405030_05

8‐4

Technical Data

Dimensions (contd.)

20 (0.79 in.)

39,8 (1.56 in.)

1/2 - 20UNF

51 (2.01 in.)

120 (4.72 in.)

92,6 (3.65 in.)

10 (0.39 in.) 24,5 (0.96 in.) 30 (1.18 in.)

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Technical Data

8‐5

Dimensions (contd.)

45 mm (1.77 in.)

33 mm (1.30 in) 52,7 mm (2.07 in)

115,7 mm (4.56 in)

121 mm (4.76 in)

35 mm (1.38 in.) 9 mm (0.35 in.) 46,5 mm (1.83 in.)

81,5 mm (3,3 .2 in.)

113,7 mm (4.48 in)

99 mm (3.9 in.)

26,5 mm (1.04 in.)

129 mm (5.08 in)

 2014 Nordson Corporation

LV 227 Edition 06/14

P/N 405030_05

Technical Data

110 mm (4.33 in)

81,5 mm (3,3 .2 in.)

99 mm (3.9 in.)

45 mm (1.77 in.)

35 mm (1.38 in.) 46,5 mm (1.83 in.)

8‐6

9 mm (0.35 in.) 62 mm (2.44 in)

122 mm (4.80 in)

119,1 mm (4.69 in)

33,9 mm (1.33 in)

26,5 mm (1.04 in.)

127,1 mm (5.00 in)

P/N 405030_05

LV 227 Edition 06/14

 2014 Nordson Corporation

Technical Data

8‐7

Dimensions (contd.) 353 mm (13.90 in) 295 mm (11.61 in)

488 mm (19.21 in)

20 - 30 mm

(4.92 - 20.07 in)

51 mm (2.00 in)

125 - 510 mm

(0.78 - 1.18 in)

25 mm (0.98 in) 60 - 320 mm (2.36 - 12.60 in)

 2014 Nordson Corporation

LV 227 Edition 06/14

P/N 405030_05

8‐8

Technical Data

85 mm (3.34 in)

30 - 75 mm (1.18 - 2.95 in)

P/N 405030_05

18 mm (0.70 in)

156 mm (6.14 in)

120 - 145 mm (4.72 - 5.70 in)

M8

25 mm (0.98 in)

45 mm (1.77 in) 57 mm (2.24 in)

LV 227 Edition 06/14

 2014 Nordson Corporation